From: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
To: buildroot@busybox.net
Subject: [Buildroot] [EXT] Re: [PATCH 6/9] package/freescale-qoriq/cadence: new package
Date: Wed, 20 Nov 2019 10:36:25 +0100 [thread overview]
Message-ID: <20191120103625.5413f1cc@windsurf.home> (raw)
In-Reply-To: <VI1PR04MB51363A932B60CC5F422C9A4AFE4F0@VI1PR04MB5136.eurprd04.prod.outlook.com>
Hello,
On Wed, 20 Nov 2019 09:30:26 +0000
Jerry Huang <jerry.huang@nxp.com> wrote:
> > Also, "cadence" is not descriptive enough as a package name.
> > freescale-qoriq-cadence-dp-firmware perhaps? It's a bit long, but at least it's
> > descriptive.
> I think "cadence-dp-firmware" can be used for its name.
> Because it is under sub-directory " freescale-qoriq",
> we can remove the prefix " freescale-qoriq" from package name.
Being inside the freescale-qoriq doesn't improve things in any way: the
namespace of package names (and therefore variables) is global in
Buildroot.
> > Indentation is not correct, we also need a link to some upstream web site that
> > gives details about this firmware.
> Sure, I will adjust it.
>
> > Just curious: the DisplayPort really needs a firmware that runs on the main CPU,
> > at EL3 ? This is pretty scary :-/ How does it get loaded ?
> Yes, LS1028ARDB need this firmware for display port.
> We used the command "hdp load" in uboot before starting Linux kernel.
OK. Where is this firmware image stored? You just install it to
$(BINARIES_DIR). Should it be installed in the rootfs instead, so that
U-Boot can pick it up from there ?
Thanks,
Thomas
--
Thomas Petazzoni, CTO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
next prev parent reply other threads:[~2019-11-20 9:36 UTC|newest]
Thread overview: 39+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-11-20 4:07 [Buildroot] [PATCH 0/9] new board ls1028ardb introduced Changming Huang
2019-11-20 4:07 ` [Buildroot] [PATCH 1/9] package/rcw: upgrade the rcw version to LSDK-19.09 Changming Huang
2019-11-20 7:59 ` Thomas Petazzoni
2019-11-20 8:04 ` [Buildroot] [EXT] " Jerry Huang
2019-11-20 9:21 ` [Buildroot] " Michael Walle
2019-11-20 9:32 ` Thomas Petazzoni
2019-11-20 9:38 ` Matthew Weber
2019-11-20 9:45 ` Thomas Petazzoni
2019-11-20 9:51 ` [Buildroot] [External] " Matthew Weber
2019-11-20 9:57 ` [Buildroot] [EXT] " Jerry Huang
2019-11-20 10:00 ` [Buildroot] " Michael Walle
2019-11-20 10:23 ` Matthew Weber
2019-11-20 9:54 ` [Buildroot] [EXT] " Jerry Huang
2019-11-20 4:07 ` [Buildroot] [PATCH 2/9] package/rcw: add target rcw binary support Changming Huang
2019-11-20 9:30 ` Matthew Weber
2019-11-20 4:07 ` [Buildroot] [PATCH 3/9] boot/arm-trusted-firmware: Add u-boot-dtb.bin support Changming Huang
2019-11-20 7:37 ` Sergey Matyukevich
2019-11-20 8:13 ` [Buildroot] [EXT] " Jerry Huang
2019-11-20 9:07 ` [Buildroot] " Thomas Petazzoni
2019-11-20 4:07 ` [Buildroot] [PATCH 4/9] boot/arm-trusted-firmware: Add RCW support Changming Huang
2019-11-20 7:50 ` Sergey Matyukevich
2019-11-20 8:45 ` [Buildroot] [EXT] " Jerry Huang
2019-11-21 8:02 ` Sergey Matyukevich
2019-11-21 8:37 ` Jerry Huang
2019-11-21 8:39 ` Jerry Huang
2019-11-20 4:07 ` [Buildroot] [PATCH 5/9] package/freescale-qoriq: new package directory Changming Huang
2019-11-20 8:57 ` Thomas Petazzoni
2019-11-20 4:07 ` [Buildroot] [PATCH 6/9] package/freescale-qoriq/cadence: new package Changming Huang
2019-11-20 9:13 ` Thomas Petazzoni
2019-11-20 9:30 ` [Buildroot] [EXT] " Jerry Huang
2019-11-20 9:36 ` Thomas Petazzoni [this message]
2019-11-20 9:47 ` Jerry Huang
2019-11-20 4:07 ` [Buildroot] [PATCH 7/9] package/rcw: Enable IIC5_PMUX and CLK_OUT_PMUX for GPIO Changming Huang
2019-11-20 9:14 ` Thomas Petazzoni
2019-11-20 9:34 ` [Buildroot] [EXT] " Jerry Huang
2019-11-20 9:38 ` Thomas Petazzoni
2019-11-20 10:22 ` Jerry Huang
2019-11-20 4:07 ` [Buildroot] [PATCH 8/9] board/freescale/common/ls: Add standard post image script for Layerscape processors Changming Huang
2019-11-20 4:07 ` [Buildroot] [PATCH 9/9] configs/freescale_ls1028ardb*: new board Changming Huang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191120103625.5413f1cc@windsurf.home \
--to=thomas.petazzoni@bootlin.com \
--cc=buildroot@busybox.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox