* [Buildroot] [PATCH v2] board/olimex/stmp1_olinuxino: add STMP157-OLinuXino-LIME2 board support
@ 2021-12-11 8:09 Francois Perrad
2021-12-17 22:00 ` Thomas Petazzoni
0 siblings, 1 reply; 2+ messages in thread
From: Francois Perrad @ 2021-12-11 8:09 UTC (permalink / raw)
To: buildroot
kernel:
- the device tree is not yet mainline
- ITE IT66121 (HDMI) is mainline only since 5.14
u-boot:
- the device tree is not yet mainline
- this board uses AXP209 as PMIC instead of the STPMIC1,
this use case of AXP209 is not mainline
arm-trusted-firmware:
at this time, there is no patch for this board,
so u-boot-spl is used as FSBL (basic boot chain)
---
board/olimex/stmp1_olinuxino/genimage.cfg | 25 +
.../linux-dts/stm32mp1xx-olinuxino-lime.dts | 379 ++++++
board/olimex/stmp1_olinuxino/linux.config | 285 +++++
.../0001-add-driver-bridge-hdmi-it66121.patch | 1054 +++++++++++++++++
.../linux/0002-more-display-olimex.patch | 175 +++
.../uboot/0001-AXP-not-only-with-sunxi.patch | 168 +++
.../uboot/0002-uses-AXP209-as-PMIC.patch | 205 ++++
.../0003-add-ethaddr-in-u-boot-env.patch | 25 +
board/olimex/stmp1_olinuxino/readme.txt | 53 +
.../boot/extlinux/extlinux.conf | 4 +
.../stm32mp1-olinuxino-lime-u-boot.dtsi | 198 ++++
.../uboot-dts/stm32mp1-olinuxino-lime.dts | 368 ++++++
board/olimex/stmp1_olinuxino/uboot.fragment | 16 +
.../olimex_stmp157_olinuxino_lime_defconfig | 51 +
14 files changed, 3006 insertions(+)
create mode 100644 board/olimex/stmp1_olinuxino/genimage.cfg
create mode 100644 board/olimex/stmp1_olinuxino/linux-dts/stm32mp1xx-olinuxino-lime.dts
create mode 100644 board/olimex/stmp1_olinuxino/linux.config
create mode 100644 board/olimex/stmp1_olinuxino/patches/linux/0001-add-driver-bridge-hdmi-it66121.patch
create mode 100644 board/olimex/stmp1_olinuxino/patches/linux/0002-more-display-olimex.patch
create mode 100644 board/olimex/stmp1_olinuxino/patches/uboot/0001-AXP-not-only-with-sunxi.patch
create mode 100644 board/olimex/stmp1_olinuxino/patches/uboot/0002-uses-AXP209-as-PMIC.patch
create mode 100644 board/olimex/stmp1_olinuxino/patches/uboot/0003-add-ethaddr-in-u-boot-env.patch
create mode 100644 board/olimex/stmp1_olinuxino/readme.txt
create mode 100644 board/olimex/stmp1_olinuxino/rootfs_overlay/boot/extlinux/extlinux.conf
create mode 100644 board/olimex/stmp1_olinuxino/uboot-dts/stm32mp1-olinuxino-lime-u-boot.dtsi
create mode 100644 board/olimex/stmp1_olinuxino/uboot-dts/stm32mp1-olinuxino-lime.dts
create mode 100644 board/olimex/stmp1_olinuxino/uboot.fragment
create mode 100644 configs/olimex_stmp157_olinuxino_lime_defconfig
diff --git a/board/olimex/stmp1_olinuxino/genimage.cfg b/board/olimex/stmp1_olinuxino/genimage.cfg
new file mode 100644
index 000000000..2f00ee979
--- /dev/null
+++ b/board/olimex/stmp1_olinuxino/genimage.cfg
@@ -0,0 +1,25 @@
+image sdcard.img {
+ hdimage {
+ gpt = "true"
+ }
+
+ partition fsbl1 {
+ image = "u-boot-spl.stm32"
+ size = 256K
+ }
+
+ partition fsbl2 {
+ image = "u-boot-spl.stm32"
+ size = 256K
+ }
+
+ partition ssbl {
+ image = "u-boot.img"
+ size = 2M
+ }
+
+ partition rootfs {
+ image = "rootfs.ext4"
+ bootable = "yes"
+ }
+}
diff --git a/board/olimex/stmp1_olinuxino/linux-dts/stm32mp1xx-olinuxino-lime.dts b/board/olimex/stmp1_olinuxino/linux-dts/stm32mp1xx-olinuxino-lime.dts
new file mode 100644
index 000000000..aa6029272
--- /dev/null
+++ b/board/olimex/stmp1_olinuxino/linux-dts/stm32mp1xx-olinuxino-lime.dts
@@ -0,0 +1,379 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
+ */
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+ model = "STM32MP1XX OLinuXino";
+ compatible = "olimex,stm32mp1xx-olinuxino-lime" , "st,stm32mp153";
+ aliases {
+ ethernet0 = ðernet0;
+ serial0 = &uart4;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@c0000000 {
+ device_type = "memory";
+ reg = <0xC0000000 0x40000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mcuram2: mcuram2@10000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10000000 0x40000>;
+ no-map;
+ };
+
+ vdev0vring0: vdev0vring0@10040000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10040000 0x1000>;
+ no-map;
+ };
+
+ vdev0vring1: vdev0vring1@10041000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10041000 0x1000>;
+ no-map;
+ };
+
+ vdev0buffer: vdev0buffer@10042000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10042000 0x4000>;
+ no-map;
+ };
+
+ mcuram: mcuram@30000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x30000000 0x40000>;
+ no-map;
+ };
+
+ retram: retram@38000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x38000000 0x10000>;
+ no-map;
+ };
+
+ gpu_reserved: gpu@e8000000 {
+ reg = <0xe8000000 0x8000000>;
+ no-map;
+ };
+ };
+
+ vdd_sd3v3: regulator_vdd {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ //regulator-over-current-protection;
+ };
+
+ hdmi_3v3: regulator_hdmi {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-hdmi";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ //regulator-over-current-protection;
+ };
+
+ hdmi_1v8: regulator_hdmi1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-hdmi1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ //regulator-over-current-protection;
+ };
+
+ hdmi_1v2: regulator_hdmi1v2 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-hdmi1v2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ //regulator-over-current-protection;
+ };
+
+ vbus_otg: regulator_otg {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-otg";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
+ enable-active-high;
+ regulator-initial-mode = <0>;
+ //regulator-over-current-protection;
+ };
+
+ vdd: vdd {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ //regulator-over-current-protection;
+ };
+
+ vdd_usb: vdd-usb {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ //regulator-over-current-protection;
+ };
+
+ panel {
+ compatible = "olimex,lcd-olinuxino-10";
+ status = "disabled";
+
+ enable-gpios = <&gpiof 13 GPIO_ACTIVE_HIGH>;
+ //backlight = <&backlight>;
+
+ port {
+ panel_in_tcon0: endpoint {
+ remote-endpoint = <<dc_ep0_out>;
+ };
+ };
+ };
+};
+
+&dts {
+ status = "okay";
+};
+
+<dc {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <<dc_pins_b>;
+ pinctrl-1 = <<dc_sleep_pins_b>;
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ltdc_ep0_out: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&it66121_in>;
+ };
+ };
+};
+
+ðernet0 {
+ status = "okay";
+ pinctrl-0 = <ðernet0_rgmii_pins_a>;
+ pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rgmii-id";
+ phy-handle = <ðphy>;
+
+ mdio0 {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ethphy: ethernet-phy@1 {
+ reg = <1>;
+ reset-gpios = <&gpiod 10 GPIO_ACTIVE_LOW>; /* ETH_RST# */
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ micrel,force-master;
+ };
+ };
+};
+
+&gpu {
+ contiguous-area = <&gpu_reserved>;
+ status = "okay";
+};
+
+&m_can1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&m_can1_pins_a>;
+ pinctrl-1 = <&m_can1_sleep_pins_a>;
+ status = "okay";
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins_a>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ it66121hdmitx: it66121hdmitx@4d {
+ compatible = "ite,it66121";
+ interrupts = <8 2>;
+ interrupt-parent = <&gpioi>;
+ vcn33-supply = <&hdmi_3v3>;
+ vcn18-supply = <&hdmi_1v8>;
+ vrf12-supply = <&hdmi_1v2>;
+ reset-gpios = <&gpiof 3 GPIO_ACTIVE_LOW >;
+ reg = <0x4d>;
+ pclk-dual-edge;
+
+ port {
+ it66121_in: endpoint {
+ remote-endpoint = <<dc_ep0_out>;
+ };
+ };
+ };
+};
+
+&ipcc {
+ status = "okay";
+};
+
+&iwdg2 {
+ timeout-sec = <32>;
+ status = "okay";
+};
+
+&m4_rproc {
+ memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+ <&vdev0vring1>, <&vdev0buffer>;
+ mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+ mbox-names = "vq0", "vq1", "shutdown";
+ interrupt-parent = <&exti>;
+ interrupts = <68 1>;
+ status = "disabled";
+};
+
+&pwr_regulators {
+ vdd-supply = <&vdd>;
+ vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&rng1 {
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
+ broken-cd;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&vdd_sd3v3>;
+ vqmmc-supply = <&vdd_sd3v3>;
+ status = "okay";
+};
+
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+ non-removable;
+ st,neg-edge;
+ bus-width = <8>;
+ vmmc-supply = <&vdd_sd3v3>;
+ vqmmc-supply = <&vdd_sd3v3>;
+ status = "okay";
+};
+
+&qspi {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
+ pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>;
+ reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ flash0: w25q128@0 {
+ compatible = "jedec,spi-nor", "winbond,w25q128";
+ reg = <0>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
+&timers6 {
+ status = "okay";
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ timer@5 {
+ status = "okay";
+ };
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_a>;
+ status = "okay";
+};
+
+&usbphyc {
+ status = "okay";
+};
+
+&usbphyc_port0 {
+ phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+ phy-supply = <&vdd_usb>;
+};
+
+&usbh_ehci {
+ phys = <&usbphyc_port0>, <&usbphyc_port1 1>;
+ phy-names = "usb", "usb";
+ status = "okay";
+};
+
+&usbh_ohci {
+ phys = <&usbphyc_port0>, <&usbphyc_port1 1>;
+ phy-names = "usb", "usb";
+ status = "okay";
+};
+
+&usbotg_hs {
+ compatible = "st,stm32mp15-fsotg", "snps,dwc2"; /* Use full-speed integrated PHY */
+ pinctrl-names = "default";
+ pinctrl-0 = <&usbotg_hs_pins_a &usbotg_fs_dp_dm_pins_a>; /* configure OTG ID and full-speed data pins */
+ vbus-supply = <&vbus_otg>; /* voltage regulator to supply Vbus */
+ status = "okay";
+};
diff --git a/board/olimex/stmp1_olinuxino/linux.config b/board/olimex/stmp1_olinuxino/linux.config
new file mode 100644
index 000000000..96c316b2c
--- /dev/null
+++ b/board/olimex/stmp1_olinuxino/linux.config
@@ -0,0 +1,285 @@
+
+#
+# General setup
+#
+CONFIG_SYSVIPC=y
+CONFIG_PREEMPT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_NAMESPACES=y
+CONFIG_EMBEDDED=y
+
+#
+# System Type
+#
+CONFIG_ARCH_STM32=y
+CONFIG_ARM_THUMBEE=y
+
+#
+# Kernel Features
+#
+CONFIG_SMP=y
+CONFIG_HIGHMEM=y
+
+#
+# Floating point emulation
+#
+CONFIG_VFP=y
+CONFIG_NEON=y
+CONFIG_KERNEL_MODE_NEON=y
+
+#
+# Cryptographic API
+#
+CONFIG_ARM_CRYPTO=y
+
+#
+# General architecture-dependent options
+#
+CONFIG_MODULES=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+
+#
+# Networking options
+#
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+
+#
+# CAN Device Drivers
+#
+CONFIG_CAN=m
+CONFIG_CAN_M_CAN=m
+CONFIG_CAN_M_CAN_PLATFORM=m
+
+# CONFIG_WIRELESS is not set
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER=y
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+
+#
+# Device Tree and Open Firmware support
+#
+CONFIG_OF_OVERLAY=y
+
+#
+# Block devices
+#
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=4
+
+#
+# Network device support
+#
+CONFIG_NETDEVICES=y
+CONFIG_STMMAC_ETH=y
+CONFIG_MICREL_PHY=y
+
+# CONFIG_WLAN is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT_MOUSEDEV=m
+CONFIG_INPUT_EVDEV=m
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_AXP20X_PEK=m
+
+#
+# Character devices
+#
+CONFIG_SERIAL_STM32=y
+CONFIG_SERIAL_STM32_CONSOLE=y
+CONFIG_NULL_TTY=m
+CONFIG_SERIAL_DEV_BUS=m
+CONFIG_HW_RANDOM=y
+
+#
+# I2C support
+#
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_STM32F7=y
+
+#
+# SPI support
+#
+CONFIG_SPI=y
+CONFIG_SPI_MEM=y
+CONFIG_SPI_STM32=m
+CONFIG_SPI_STM32_QSPI=m
+
+#
+# Pin controllers
+#
+CONFIG_PINCTRL_AXP209=m
+
+#
+# Board level reset or power off
+#
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_GPIO=y
+CONFIG_POWER_RESET_GPIO_RESTART=y
+
+#
+# Thermal drivers
+#
+CONFIG_THERMAL_DEFAULT_GOV_FAIR_SHARE=y
+CONFIG_CPU_THERMAL=y
+
+#
+# Watchdog Timer Support
+#
+CONFIG_WATCHDOG=y
+
+#
+# Multifunction device drivers
+#
+CONFIG_MFD_AXP20X_I2C=y
+CONFIG_MFD_STM32_LPTIMER=y
+
+#
+# Voltage and Current Regulator Support
+#
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_AXP20X=y
+CONFIG_REGULATOR_STM32_VREFBUF=y
+CONFIG_REGULATOR_STM32_PWR=y
+
+#
+# Graphics support
+#
+CONFIG_DRM=y
+CONFIG_DRM_STM=m
+CONFIG_DRM_STM_DSI=m
+CONFIG_DRM_PANEL_LVDS=m
+CONFIG_DRM_PANEL_SIMPLE=m
+CONFIG_DRM_PANEL_OLIMEX_LCD_OLINUXINO=m
+CONFIG_DRM_ITE_IT66121=m
+CONFIG_DRM_ETNAVIV=m
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_BACKLIGHT_PWM=m
+CONFIG_BACKLIGHT_GPIO=m
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+
+#
+# USB support
+#
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+
+#
+# MMC/SD/SDIO card support
+#
+CONFIG_MMC=y
+CONFIG_MMC_ARMMMCI=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+
+#
+# LED drivers
+#
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+
+#
+# Real Time Clock
+#
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_STM32=y
+
+#
+# DMA Devices
+#
+CONFIG_DMADEVICES=y
+CONFIG_STM32_DMA=y
+CONFIG_STM32_DMAMUX=y
+CONFIG_STM32_MDMA=y
+
+#
+# Userspace I/O drivers
+#
+CONFIG_UIO=m
+CONFIG_UIO_PDRV_GENIRQ=m
+CONFIG_UIO_DMEM_GENIRQ=m
+
+#
+# Hardware Spinlock drivers
+#
+CONFIG_HWSPINLOCK=y
+CONFIG_HWSPINLOCK_STM32=y
+
+#
+# Clock Source driver
+#
+CONFIG_CLKSRC_STM32_LP=y
+
+#
+# Mailbox Hardware Support
+#
+CONFIG_STM32_IPCC=y
+
+#
+# Remoteproc drivers
+#
+CONFIG_REMOTEPROC=y
+CONFIG_STM32_RPROC=y
+
+#
+# Industrial I/O support
+#
+CONFIG_IIO=y
+CONFIG_IIO_SW_TRIGGER=y
+CONFIG_SD_ADC_MODULATOR=y
+CONFIG_STM32_ADC_CORE=y
+CONFIG_STM32_ADC=y
+CONFIG_STM32_DFSDM_ADC=y
+CONFIG_STM32_DAC=y
+CONFIG_IIO_HRTIMER_TRIGGER=y
+CONFIG_IIO_STM32_LPTIMER_TRIGGER=y
+
+#
+# PWM Support
+#
+CONFIG_PWM=y
+CONFIG_PWM_STM32=m
+CONFIG_PWM_STM32_LP=m
+
+#
+# PHY Subsystem
+#
+CONFIG_PHY_STM32_USBPHYC=y
+
+#
+# NVMEM Support
+#
+CONFIG_NVMEM_STM32_ROMEM=y
+
+#
+# File systems
+#
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_VFAT_FS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+
+#
+# Kernel hacking
+#
+CONFIG_PRINTK_TIME=y
diff --git a/board/olimex/stmp1_olinuxino/patches/linux/0001-add-driver-bridge-hdmi-it66121.patch b/board/olimex/stmp1_olinuxino/patches/linux/0001-add-driver-bridge-hdmi-it66121.patch
new file mode 100644
index 000000000..c2540f40e
--- /dev/null
+++ b/board/olimex/stmp1_olinuxino/patches/linux/0001-add-driver-bridge-hdmi-it66121.patch
@@ -0,0 +1,1054 @@
+From 6ed027bda27b01ea2b53f4a8eb0c14d2223b7f13 Mon Sep 17 00:00:00 2001
+From: Francois Perrad <francois.perrad@gadz.org>
+Date: Thu, 28 Oct 2021 20:32:11 +0200
+Subject: [PATCH] add driver bridge hdmi it66121
+
+fetched from https://github.com/OLIMEX/linux-olimex
+
+Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
+---
+ drivers/gpu/drm/bridge/Kconfig | 8 +
+ drivers/gpu/drm/bridge/Makefile | 1 +
+ drivers/gpu/drm/bridge/ite-it66121.c | 999 +++++++++++++++++++++++++++
+ 3 files changed, 1008 insertions(+)
+ create mode 100644 drivers/gpu/drm/bridge/ite-it66121.c
+
+diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
+index 4e82647a6..2e332e303 100644
+--- a/drivers/gpu/drm/bridge/Kconfig
++++ b/drivers/gpu/drm/bridge/Kconfig
+@@ -71,6 +71,14 @@ config DRM_LVDS_CODEC
+ Support for transparent LVDS encoders and decoders that don't
+ require any configuration.
+
++config DRM_ITE_IT66121
++ tristate "ITE IT66121 HDMI bridge"
++ depends on OF
++ select DRM_KMS_HELPER
++ select REGMAP_I2C
++ help
++ Support for ITE IT66121 HDMI bridge.
++
+ config DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW
+ tristate "MegaChips stdp4028-ge-b850v3-fw and stdp2690-ge-b850v3-fw"
+ depends on OF
+diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
+index 2b3aff104..98dff3d2d 100644
+--- a/drivers/gpu/drm/bridge/Makefile
++++ b/drivers/gpu/drm/bridge/Makefile
+@@ -3,6 +3,7 @@ obj-$(CONFIG_DRM_CDNS_DSI) += cdns-dsi.o
+ obj-$(CONFIG_DRM_CHRONTEL_CH7033) += chrontel-ch7033.o
+ obj-$(CONFIG_DRM_DISPLAY_CONNECTOR) += display-connector.o
+ obj-$(CONFIG_DRM_LONTIUM_LT9611) += lontium-lt9611.o
++obj-$(CONFIG_DRM_ITE_IT66121) += ite-it66121.o
+ obj-$(CONFIG_DRM_LVDS_CODEC) += lvds-codec.o
+ obj-$(CONFIG_DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW) += megachips-stdpxxxx-ge-b850v3-fw.o
+ obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
+diff --git a/drivers/gpu/drm/bridge/ite-it66121.c b/drivers/gpu/drm/bridge/ite-it66121.c
+new file mode 100644
+index 000000000..863c95240
+--- /dev/null
++++ b/drivers/gpu/drm/bridge/ite-it66121.c
+@@ -0,0 +1,999 @@
++// SPDX-License-Identifier: GPL-2.0-only
++/*
++ * Copyright (C) 2020 Dimitar Gamishev <hehopmajieh@debian.bg>
++ * Copyright (C) 2020 BayLibre, SAS
++ * Author: Phong LE <ple@baylibre.com>
++ * Copyright (C) 2018-2019, Artem Mygaiev
++ * Copyright (C) 2017, Fresco Logic, Incorporated.
++ *
++ */
++
++#include <linux/device.h>
++#include <linux/i2c.h>
++#include <linux/interrupt.h>
++#include <linux/module.h>
++#include <linux/of.h>
++#include <linux/of_device.h>
++#include <linux/of_gpio.h>
++#include <linux/pinctrl/consumer.h>
++#include <linux/regmap.h>
++#include <linux/regulator/consumer.h>
++
++#include <drm/drm_atomic_helper.h>
++#include <drm/drm_bridge.h>
++#include <drm/drm_crtc_helper.h>
++#include <drm/drm_edid.h>
++#include <drm/drm_modes.h>
++#include <drm/drm_print.h>
++#include <drm/drm_probe_helper.h>
++
++#define IT66121_MASTER_SEL_REG 0x10
++#define IT66121_MASTER_SEL_HOST BIT(0)
++
++#define IT66121_AFE_DRV_REG 0x61
++#define IT66121_AFE_DRV_RST BIT(4)
++#define IT66121_AFE_DRV_PWD BIT(5)
++
++#define IT66121_INPUT_MODE_REG 0x70
++#define IT66121_INPUT_MODE_RGB (0 << 6)
++#define IT66121_INPUT_MODE_YUV422 BIT(6)
++#define IT66121_INPUT_MODE_YUV444 (2 << 6)
++#define IT66121_INPUT_MODE_CCIR656 BIT(4)
++#define IT66121_INPUT_MODE_SYNCEMB BIT(3)
++#define IT66121_INPUT_MODE_DDR BIT(2)
++
++#define IT66121_INPUT_CSC_REG 0x72
++#define IT66121_INPUT_CSC_ENDITHER BIT(7)
++#define IT66121_INPUT_CSC_ENUDFILTER BIT(6)
++#define IT66121_INPUT_CSC_DNFREE_GO BIT(5)
++#define IT66121_INPUT_CSC_RGB_TO_YUV 0x02
++#define IT66121_INPUT_CSC_YUV_TO_RGB 0x03
++#define IT66121_INPUT_CSC_NO_CONV 0x00
++
++#define IT66121_AFE_XP_REG 0x62
++#define IT66121_AFE_XP_GAINBIT BIT(7)
++#define IT66121_AFE_XP_PWDPLL BIT(6)
++#define IT66121_AFE_XP_ENI BIT(5)
++#define IT66121_AFE_XP_ENO BIT(4)
++#define IT66121_AFE_XP_RESETB BIT(3)
++#define IT66121_AFE_XP_PWDI BIT(2)
++
++#define IT66121_AFE_IP_REG 0x64
++#define IT66121_AFE_IP_GAINBIT BIT(7)
++#define IT66121_AFE_IP_PWDPLL BIT(6)
++#define IT66121_AFE_IP_CKSEL_05 (0 << 4)
++#define IT66121_AFE_IP_CKSEL_1 BIT(4)
++#define IT66121_AFE_IP_CKSEL_2 (2 << 4)
++#define IT66121_AFE_IP_CKSEL_2OR4 (3 << 4)
++#define IT66121_AFE_IP_ER0 BIT(3)
++#define IT66121_AFE_IP_RESETB BIT(2)
++#define IT66121_AFE_IP_ENC BIT(1)
++#define IT66121_AFE_IP_EC1 BIT(0)
++
++#define IT66121_AFE_XP_EC1_REG 0x68
++#define IT66121_AFE_XP_EC1_LOWCLK BIT(4)
++
++#define IT66121_SW_RST_REG 0x04
++#define IT66121_SW_RST_REF BIT(5)
++#define IT66121_SW_RST_AREF BIT(4)
++#define IT66121_SW_RST_VID BIT(3)
++#define IT66121_SW_RST_AUD BIT(2)
++#define IT66121_SW_RST_HDCP BIT(0)
++
++#define IT66121_DDC_COMMAND_REG 0x15
++#define IT66121_DDC_COMMAND_BURST_READ 0x0
++#define IT66121_DDC_COMMAND_EDID_READ 0x3
++#define IT66121_DDC_COMMAND_FIFO_CLR 0x9
++#define IT66121_DDC_COMMAND_SCL_PULSE 0xA
++#define IT66121_DDC_COMMAND_ABORT 0xF
++
++#define IT66121_HDCP_REG 0x20
++#define IT66121_HDCP_CPDESIRED BIT(0)
++#define IT66121_HDCP_EN1P1FEAT BIT(1)
++
++#define IT66121_INT_STATUS1_REG 0x06
++#define IT66121_INT_STATUS1_AUD_OVF BIT(7)
++#define IT66121_INT_STATUS1_DDC_NOACK BIT(5)
++#define IT66121_INT_STATUS1_DDC_FIFOERR BIT(4)
++#define IT66121_INT_STATUS1_DDC_BUSHANG BIT(2)
++#define IT66121_INT_STATUS1_RX_SENS_STATUS BIT(1)
++#define IT66121_INT_STATUS1_HPD_STATUS BIT(0)
++
++#define IT66121_DDC_HEADER_REG 0x11
++#define IT66121_DDC_HEADER_HDCP 0x74
++#define IT66121_DDC_HEADER_EDID 0xA0
++
++#define IT66121_DDC_OFFSET_REG 0x12
++#define IT66121_DDC_BYTE_REG 0x13
++#define IT66121_DDC_SEGMENT_REG 0x14
++#define IT66121_DDC_RD_FIFO_REG 0x17
++
++#define IT66121_CLK_BANK_REG 0x0F
++#define IT66121_CLK_BANK_PWROFF_RCLK BIT(6)
++#define IT66121_CLK_BANK_PWROFF_ACLK BIT(5)
++#define IT66121_CLK_BANK_PWROFF_TXCLK BIT(4)
++#define IT66121_CLK_BANK_PWROFF_CRCLK BIT(3)
++#define IT66121_CLK_BANK_0 0
++#define IT66121_CLK_BANK_1 1
++
++#define IT66121_INT_REG 0x05
++#define IT66121_INT_ACTIVE_HIGH BIT(7)
++#define IT66121_INT_OPEN_DRAIN BIT(6)
++#define IT66121_INT_TX_CLK_OFF BIT(0)
++
++#define IT66121_INT_MASK1_REG 0x09
++#define IT66121_INT_MASK1_AUD_OVF BIT(7)
++#define IT66121_INT_MASK1_DDC_NOACK BIT(5)
++#define IT66121_INT_MASK1_DDC_FIFOERR BIT(4)
++#define IT66121_INT_MASK1_DDC_BUSHANG BIT(2)
++#define IT66121_INT_MASK1_RX_SENS BIT(1)
++#define IT66121_INT_MASK1_HPD BIT(0)
++
++#define IT66121_INT_CLR1_REG 0x0C
++#define IT66121_INT_CLR1_PKTACP BIT(7)
++#define IT66121_INT_CLR1_PKTNULL BIT(6)
++#define IT66121_INT_CLR1_PKTGEN BIT(5)
++#define IT66121_INT_CLR1_KSVLISTCHK BIT(4)
++#define IT66121_INT_CLR1_AUTHDONE BIT(3)
++#define IT66121_INT_CLR1_AUTHFAIL BIT(2)
++#define IT66121_INT_CLR1_RX_SENS BIT(1)
++#define IT66121_INT_CLR1_HPD BIT(0)
++
++#define IT66121_AV_MUTE_REG 0xC1
++#define IT66121_AV_MUTE_ON BIT(0)
++#define IT66121_AV_MUTE_BLUESCR BIT(1)
++
++#define IT66121_PKT_GEN_CTRL_REG 0xC6
++#define IT66121_PKT_GEN_CTRL_ON BIT(0)
++#define IT66121_PKT_GEN_CTRL_RPT BIT(1)
++
++#define IT66121_AVIINFO_DB1_REG 0x158
++#define IT66121_AVIINFO_DB2_REG 0x159
++#define IT66121_AVIINFO_DB3_REG 0x15A
++#define IT66121_AVIINFO_DB4_REG 0x15B
++#define IT66121_AVIINFO_DB5_REG 0x15C
++#define IT66121_AVIINFO_CSUM_REG 0x15D
++#define IT66121_AVIINFO_DB6_REG 0x15E
++#define IT66121_AVIINFO_DB7_REG 0x15F
++#define IT66121_AVIINFO_DB8_REG 0x160
++#define IT66121_AVIINFO_DB9_REG 0x161
++#define IT66121_AVIINFO_DB10_REG 0x162
++#define IT66121_AVIINFO_DB11_REG 0x163
++#define IT66121_AVIINFO_DB12_REG 0x164
++#define IT66121_AVIINFO_DB13_REG 0x165
++
++#define IT66121_AVI_INFO_PKT_REG 0xCD
++#define IT66121_AVI_INFO_PKT_ON BIT(0)
++#define IT66121_AVI_INFO_PKT_RPT BIT(1)
++
++#define IT66121_HDMI_MODE_REG 0xC0
++#define IT66121_HDMI_MODE_HDMI BIT(0)
++
++#define IT66121_SYS_STATUS_REG 0x0E
++#define IT66121_SYS_STATUS_ACTIVE_IRQ BIT(7)
++#define IT66121_SYS_STATUS_HPDETECT BIT(6)
++#define IT66121_SYS_STATUS_SENDECTECT BIT(5)
++#define IT66121_SYS_STATUS_VID_STABLE BIT(4)
++#define IT66121_SYS_STATUS_AUD_CTS_CLR BIT(1)
++#define IT66121_SYS_STATUS_CLEAR_IRQ BIT(0)
++
++#define IT66121_DDC_STATUS_REG 0x16
++#define IT66121_DDC_STATUS_TX_DONE BIT(7)
++#define IT66121_DDC_STATUS_ACTIVE BIT(6)
++#define IT66121_DDC_STATUS_NOACK BIT(5)
++#define IT66121_DDC_STATUS_WAIT_BUS BIT(4)
++#define IT66121_DDC_STATUS_ARBI_LOSE BIT(3)
++#define IT66121_DDC_STATUS_FIFO_FULL BIT(2)
++#define IT66121_DDC_STATUS_FIFO_EMPTY BIT(1)
++#define IT66121_DDC_STATUS_FIFO_VALID BIT(0)
++
++#define IT66121_VENDOR_ID0 0x54
++#define IT66121_VENDOR_ID1 0x49
++#define IT66121_DEVICE_ID0 0x12
++#define IT66121_DEVICE_ID1 0x06
++#define IT66121_DEVICE_MASK 0x0F
++#define IT66121_EDID_SLEEP 20000
++#define IT66121_EDID_TIMEOUT 200000
++#define IT66121_EDID_FIFO_SIZE 32
++#define IT66121_AFE_CLK_HIGH 80000
++
++struct it66121_conf {
++ unsigned int input_mode_reg;
++ unsigned int input_conversion_reg;
++};
++
++struct it66121_ctx {
++ struct regmap *regmap;
++ struct drm_bridge bridge;
++ struct drm_connector connector;
++ struct device *dev;
++ struct gpio_desc *gpio_reset;
++ struct i2c_client *client;
++ struct regulator_bulk_data supplies[3];
++ bool dual_edge;
++ const struct it66121_conf *conf;
++ struct mutex lock; /* Protects fields below and device registers */
++ struct edid *edid;
++ struct hdmi_avi_infoframe hdmi_avi_infoframe;
++};
++
++static const struct regmap_range_cfg it66121_regmap_banks[] = {
++ {
++ .name = "it66121",
++ .range_min = 0x00,
++ .range_max = 0x1FF,
++ .selector_reg = IT66121_CLK_BANK_REG,
++ .selector_mask = 0x1,
++ .selector_shift = 0,
++ .window_start = 0x00,
++ .window_len = 0x130,
++ },
++};
++
++static const struct regmap_config it66121_regmap_config = {
++ .val_bits = 8,
++ .reg_bits = 8,
++ .max_register = 0x1FF,
++ .ranges = it66121_regmap_banks,
++ .num_ranges = ARRAY_SIZE(it66121_regmap_banks),
++};
++
++static const struct it66121_conf it66121_conf_simple = {
++// .input_mode_reg = IT66121_INPUT_MODE_RGB | IT66121_INPUT_MODE_DDR,
++ .input_mode_reg = IT66121_INPUT_MODE_RGB,
++ .input_conversion_reg = IT66121_INPUT_CSC_NO_CONV,
++};
++
++static void it66121_hw_reset(struct it66121_ctx *ctx)
++{
++ gpiod_set_value(ctx->gpio_reset, 1);
++ msleep(20);
++ gpiod_set_value(ctx->gpio_reset, 0);
++}
++
++static int ite66121_power_on(struct it66121_ctx *ctx)
++{
++ return regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
++}
++
++static int ite66121_power_off(struct it66121_ctx *ctx)
++{
++ return regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
++}
++
++static int it66121_preamble_ddc(struct it66121_ctx *ctx)
++{
++ return regmap_write(ctx->regmap, IT66121_MASTER_SEL_REG,
++ IT66121_MASTER_SEL_HOST);
++}
++
++static int it66121_fire_afe(struct it66121_ctx *ctx)
++{
++ return regmap_write(ctx->regmap, IT66121_AFE_DRV_REG, 0);
++}
++
++static int it66121_configure_input(struct it66121_ctx *ctx)
++{
++ int ret;
++
++ ret = regmap_write(ctx->regmap, IT66121_INPUT_MODE_REG,
++ ctx->conf->input_mode_reg);
++ if (ret)
++ return ret;
++
++ return regmap_write(ctx->regmap, IT66121_INPUT_CSC_REG,
++ ctx->conf->input_conversion_reg);
++}
++
++/**
++ * it66121_configure_afe() - Configure the analog front end
++ * @ctx: it66121_ctx object
++ *
++ * RETURNS:
++ * zero if success, a negative error code otherwise.
++ */
++static int it66121_configure_afe(struct it66121_ctx *ctx,
++ const struct drm_display_mode *mode)
++{
++ int ret;
++
++ ret = regmap_write(ctx->regmap, IT66121_AFE_DRV_REG,
++ IT66121_AFE_DRV_RST);
++ if (ret)
++ return ret;
++
++ if (mode->clock > IT66121_AFE_CLK_HIGH) {
++ ret = regmap_write_bits(ctx->regmap, IT66121_AFE_XP_REG,
++ IT66121_AFE_XP_GAINBIT |
++ IT66121_AFE_XP_ENO,
++ IT66121_AFE_XP_GAINBIT);
++ if (ret)
++ return ret;
++
++ ret = regmap_write_bits(ctx->regmap, IT66121_AFE_IP_REG,
++ IT66121_AFE_IP_GAINBIT |
++ IT66121_AFE_IP_ER0 |
++ IT66121_AFE_IP_EC1,
++ IT66121_AFE_IP_GAINBIT);
++ if (ret)
++ return ret;
++
++ ret = regmap_write_bits(ctx->regmap, IT66121_AFE_XP_EC1_REG,
++ IT66121_AFE_XP_EC1_LOWCLK, 0x80);
++ if (ret)
++ return ret;
++ } else {
++ ret = regmap_write_bits(ctx->regmap, IT66121_AFE_XP_REG,
++ IT66121_AFE_XP_GAINBIT |
++ IT66121_AFE_XP_ENO,
++ IT66121_AFE_XP_ENO);
++ if (ret)
++ return ret;
++
++ ret = regmap_write_bits(ctx->regmap, IT66121_AFE_IP_REG,
++ IT66121_AFE_IP_GAINBIT |
++ IT66121_AFE_IP_ER0 |
++ IT66121_AFE_IP_EC1, IT66121_AFE_IP_ER0 |
++ IT66121_AFE_IP_EC1);
++ if (ret)
++ return ret;
++
++ ret = regmap_write_bits(ctx->regmap, IT66121_AFE_XP_EC1_REG,
++ IT66121_AFE_XP_EC1_LOWCLK,
++ IT66121_AFE_XP_EC1_LOWCLK);
++ if (ret)
++ return ret;
++ }
++
++ /* Clear reset flags */
++ ret = regmap_write_bits(ctx->regmap, IT66121_SW_RST_REG,
++ IT66121_SW_RST_REF | IT66121_SW_RST_VID,
++ ~(IT66121_SW_RST_REF | IT66121_SW_RST_VID) &
++ 0xFF);
++ if (ret)
++ return ret;
++
++ return it66121_fire_afe(ctx);
++}
++
++static inline int it66121_wait_ddc_ready(struct it66121_ctx *ctx)
++{
++ int ret, val;
++
++ ret = regmap_read_poll_timeout(ctx->regmap, IT66121_DDC_STATUS_REG,
++ val, true,
++ IT66121_EDID_SLEEP,
++ IT66121_EDID_TIMEOUT);
++ if (ret)
++ return ret;
++
++ if (val & (IT66121_DDC_STATUS_NOACK | IT66121_DDC_STATUS_WAIT_BUS |
++ IT66121_DDC_STATUS_ARBI_LOSE))
++ return -EAGAIN;
++
++ return 0;
++}
++
++static int it66121_clear_ddc_fifo(struct it66121_ctx *ctx)
++{
++ int ret;
++
++ ret = it66121_preamble_ddc(ctx);
++ if (ret)
++ return ret;
++
++ return regmap_write(ctx->regmap, IT66121_DDC_COMMAND_REG,
++ IT66121_DDC_COMMAND_FIFO_CLR);
++}
++
++static int it66121_abort_ddc_ops(struct it66121_ctx *ctx)
++{
++ int ret;
++ unsigned int swreset, cpdesire;
++
++ ret = regmap_read(ctx->regmap, IT66121_SW_RST_REG, &swreset);
++ if (ret)
++ return ret;
++
++ ret = regmap_read(ctx->regmap, IT66121_HDCP_REG, &cpdesire);
++ if (ret)
++ return ret;
++
++ ret = regmap_write(ctx->regmap, IT66121_HDCP_REG,
++ cpdesire & (~IT66121_HDCP_CPDESIRED & 0xFF));
++ if (ret)
++ return ret;
++
++ ret = regmap_write(ctx->regmap, IT66121_SW_RST_REG,
++ swreset | IT66121_SW_RST_HDCP);
++ if (ret)
++ return ret;
++
++ ret = it66121_preamble_ddc(ctx);
++ if (ret)
++ return ret;
++
++ ret = regmap_write(ctx->regmap, IT66121_DDC_COMMAND_REG,
++ IT66121_DDC_COMMAND_ABORT);
++ if (ret)
++ return ret;
++
++ return it66121_wait_ddc_ready(ctx);
++}
++
++static int it66121_get_edid_block(void *context, u8 *buf,
++ unsigned int block, size_t len)
++{
++ struct it66121_ctx *ctx = context;
++ unsigned int val;
++ int remain = len;
++ int offset = 0;
++ int ret, cnt;
++
++ offset = (block % 2) * len;
++ block = block / 2;
++
++ ret = regmap_read(ctx->regmap, IT66121_INT_STATUS1_REG, &val);
++ if (ret)
++ return ret;
++
++ if (val & IT66121_INT_STATUS1_DDC_BUSHANG) {
++ ret = it66121_abort_ddc_ops(ctx);
++ if (ret)
++ return ret;
++ }
++
++ ret = it66121_clear_ddc_fifo(ctx);
++ if (ret)
++ return ret;
++
++ while (remain > 0) {
++ cnt = (remain > IT66121_EDID_FIFO_SIZE) ?
++ IT66121_EDID_FIFO_SIZE : remain;
++ ret = it66121_preamble_ddc(ctx);
++ if (ret)
++ return ret;
++
++ ret = regmap_write(ctx->regmap, IT66121_DDC_COMMAND_REG,
++ IT66121_DDC_COMMAND_FIFO_CLR);
++ if (ret)
++ return ret;
++
++ ret = it66121_wait_ddc_ready(ctx);
++ if (ret)
++ return ret;
++
++ ret = regmap_read(ctx->regmap, IT66121_INT_STATUS1_REG, &val);
++ if (ret)
++ return ret;
++
++ if (val & IT66121_INT_STATUS1_DDC_BUSHANG) {
++ ret = it66121_abort_ddc_ops(ctx);
++ if (ret)
++ return ret;
++ }
++
++ ret = it66121_preamble_ddc(ctx);
++ if (ret)
++ return ret;
++
++ ret = regmap_write(ctx->regmap, IT66121_DDC_HEADER_REG,
++ IT66121_DDC_HEADER_EDID);
++ if (ret)
++ return ret;
++
++ ret = regmap_write(ctx->regmap, IT66121_DDC_OFFSET_REG, offset);
++ if (ret)
++ return ret;
++
++ ret = regmap_write(ctx->regmap, IT66121_DDC_BYTE_REG, cnt);
++ if (ret)
++ return ret;
++
++ ret = regmap_write(ctx->regmap, IT66121_DDC_SEGMENT_REG, block);
++ if (ret)
++ return ret;
++
++ ret = regmap_write(ctx->regmap, IT66121_DDC_COMMAND_REG,
++ IT66121_DDC_COMMAND_EDID_READ);
++ if (ret)
++ return ret;
++
++ offset += cnt;
++ remain -= cnt;
++ msleep(20);
++
++ ret = it66121_wait_ddc_ready(ctx);
++ if (ret)
++ return ret;
++
++ do {
++ ret = regmap_read(ctx->regmap,
++ IT66121_DDC_RD_FIFO_REG, &val);
++ if (ret)
++ return ret;
++ *(buf++) = val;
++ cnt--;
++ } while (cnt > 0);
++ }
++
++ return 0;
++}
++
++static int it66121_connector_get_modes(struct drm_connector *connector)
++{
++ int ret, num_modes = 0;
++ struct it66121_ctx *ctx = container_of(connector, struct it66121_ctx,
++ connector);
++
++ if (ctx->edid)
++ return drm_add_edid_modes(connector, ctx->edid);
++
++ mutex_lock(&ctx->lock);
++
++ ctx->edid = drm_do_get_edid(connector, it66121_get_edid_block, ctx);
++ if (!ctx->edid) {
++ DRM_ERROR("Failed to read EDID\n");
++ goto unlock;
++ }
++
++ ret = drm_connector_update_edid_property(connector,
++ ctx->edid);
++ if (ret) {
++ DRM_ERROR("Failed to update EDID property: %d\n", ret);
++ goto unlock;
++ }
++
++ num_modes = drm_add_edid_modes(connector, ctx->edid);
++
++unlock:
++ mutex_unlock(&ctx->lock);
++
++ return num_modes;
++}
++
++static bool it66121_is_hpd_detect(struct it66121_ctx *ctx)
++{
++ int val;
++
++ if (regmap_read(ctx->regmap, IT66121_SYS_STATUS_REG, &val))
++ return false;
++
++ return (val & IT66121_SYS_STATUS_HPDETECT);
++}
++
++static int it66121_connector_detect_ctx(struct drm_connector *connector,
++ struct drm_modeset_acquire_ctx *c,
++ bool force)
++{
++ struct it66121_ctx *ctx = container_of(connector, struct it66121_ctx,
++ connector);
++
++ return (it66121_is_hpd_detect(ctx)) ?
++ connector_status_connected : connector_status_disconnected;
++}
++
++static enum drm_mode_status
++it66121_connector_mode_valid(struct drm_connector *connector,
++ struct drm_display_mode *mode)
++{
++ unsigned long max_clock;
++ struct it66121_ctx *ctx = container_of(connector, struct it66121_ctx,
++ connector);
++
++ max_clock = ctx->dual_edge ? 74250 : 148500;
++
++ if (mode->clock > max_clock)
++ return MODE_CLOCK_HIGH;
++
++ if (mode->clock < 25000)
++ return MODE_CLOCK_LOW;
++
++ return MODE_OK;
++}
++
++static struct drm_connector_helper_funcs it66121_connector_helper_funcs = {
++ .get_modes = it66121_connector_get_modes,
++ .detect_ctx = it66121_connector_detect_ctx,
++ .mode_valid = it66121_connector_mode_valid,
++};
++
++static const struct drm_connector_funcs it66121_connector_funcs = {
++ .reset = drm_atomic_helper_connector_reset,
++ .fill_modes = drm_helper_probe_single_connector_modes,
++ .destroy = drm_connector_cleanup,
++ .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
++ .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
++};
++
++static int it66121_bridge_attach(struct drm_bridge *bridge,
++ enum drm_bridge_attach_flags flags)
++{
++ int ret;
++ struct it66121_ctx *ctx = container_of(bridge, struct it66121_ctx,
++ bridge);
++#if 0
++ if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) {
++ DRM_ERROR("Fix bridge driver to make connector optional!");
++ return -EINVAL;
++ }
++#endif
++ if (!bridge->encoder) {
++ DRM_ERROR("Parent encoder object not found");
++ return -ENODEV;
++ }
++
++ ret = regmap_write_bits(ctx->regmap, IT66121_CLK_BANK_REG,
++ IT66121_CLK_BANK_PWROFF_RCLK, 0);
++ if (ret)
++ return ret;
++
++ ret = regmap_write_bits(ctx->regmap, IT66121_INT_REG,
++ IT66121_INT_TX_CLK_OFF, 0);
++ if (ret)
++ return ret;
++
++ ret = regmap_write_bits(ctx->regmap, IT66121_AFE_DRV_REG,
++ IT66121_AFE_DRV_PWD, 0);
++ if (ret)
++ return ret;
++
++ ret = regmap_write_bits(ctx->regmap, IT66121_AFE_XP_REG,
++ IT66121_AFE_XP_PWDI | IT66121_AFE_XP_PWDPLL, 0);
++ if (ret)
++ return ret;
++
++ ret = regmap_write_bits(ctx->regmap, IT66121_AFE_IP_REG,
++ IT66121_AFE_IP_PWDPLL, 0);
++ if (ret)
++ return ret;
++
++ ret = regmap_write_bits(ctx->regmap, IT66121_AFE_DRV_REG,
++ IT66121_AFE_DRV_RST, 0);
++ if (ret)
++ return ret;
++
++ ret = regmap_write_bits(ctx->regmap, IT66121_AFE_XP_REG,
++ IT66121_AFE_XP_RESETB, IT66121_AFE_XP_RESETB);
++ if (ret)
++ return ret;
++
++ ret = regmap_write_bits(ctx->regmap, IT66121_AFE_IP_REG,
++ IT66121_AFE_IP_RESETB, IT66121_AFE_IP_RESETB);
++ if (ret)
++ return ret;
++
++ ret = regmap_write_bits(ctx->regmap, IT66121_SW_RST_REG,
++ IT66121_SW_RST_REF,
++ IT66121_SW_RST_REF);
++ if (ret)
++ return ret;
++
++ msleep(50);
++
++ ret = drm_connector_init(bridge->dev, &ctx->connector,
++ &it66121_connector_funcs,
++ DRM_MODE_CONNECTOR_HDMIA);
++ if (ret)
++ return ret;
++
++ ctx->connector.polled = DRM_CONNECTOR_POLL_HPD;
++ drm_connector_helper_add(&ctx->connector,
++ &it66121_connector_helper_funcs);
++
++ ret = drm_connector_attach_encoder(&ctx->connector, bridge->encoder);
++ if (ret)
++ return ret;
++
++ ret = drm_connector_register(&ctx->connector);
++ if (ret)
++ return ret;
++
++ /* Start interrupts */
++ return regmap_write_bits(ctx->regmap, IT66121_INT_MASK1_REG,
++ IT66121_INT_MASK1_DDC_NOACK |
++ IT66121_INT_MASK1_HPD |
++ IT66121_INT_MASK1_DDC_FIFOERR |
++ IT66121_INT_MASK1_DDC_BUSHANG,
++ ~(IT66121_INT_MASK1_DDC_NOACK |
++ IT66121_INT_MASK1_HPD |
++ IT66121_INT_MASK1_DDC_FIFOERR |
++ IT66121_INT_MASK1_DDC_BUSHANG) & 0xFF);
++}
++
++static int it66121_set_mute(struct it66121_ctx *ctx, bool mute)
++{
++ int ret;
++ unsigned int val;
++
++ val = mute ? IT66121_AV_MUTE_ON : (~IT66121_AV_MUTE_ON & 0xFF);
++ ret = regmap_write_bits(ctx->regmap, IT66121_AV_MUTE_REG,
++ IT66121_AV_MUTE_ON, val);
++ if (ret)
++ return ret;
++
++ return regmap_write(ctx->regmap, IT66121_PKT_GEN_CTRL_REG,
++ IT66121_PKT_GEN_CTRL_ON |
++ IT66121_PKT_GEN_CTRL_RPT);
++}
++
++static void it66121_bridge_enable(struct drm_bridge *bridge)
++{
++ struct it66121_ctx *ctx = container_of(bridge, struct it66121_ctx,
++ bridge);
++
++ it66121_set_mute(ctx, false);
++}
++
++static void it66121_bridge_disable(struct drm_bridge *bridge)
++{
++ struct it66121_ctx *ctx = container_of(bridge, struct it66121_ctx,
++ bridge);
++
++ it66121_set_mute(ctx, true);
++}
++
++static
++void it66121_bridge_mode_set(struct drm_bridge *bridge,
++ const struct drm_display_mode *mode,
++ const struct drm_display_mode *adjusted_mode)
++{
++ int ret, i;
++ u8 buf[HDMI_INFOFRAME_SIZE(AVI)];
++ struct it66121_ctx *ctx = container_of(bridge, struct it66121_ctx,
++ bridge);
++ const u16 aviinfo_reg[HDMI_AVI_INFOFRAME_SIZE] = {
++ IT66121_AVIINFO_DB1_REG,
++ IT66121_AVIINFO_DB2_REG,
++ IT66121_AVIINFO_DB3_REG,
++ IT66121_AVIINFO_DB4_REG,
++ IT66121_AVIINFO_DB5_REG,
++ IT66121_AVIINFO_DB6_REG,
++ IT66121_AVIINFO_DB7_REG,
++ IT66121_AVIINFO_DB8_REG,
++ IT66121_AVIINFO_DB9_REG,
++ IT66121_AVIINFO_DB10_REG,
++ IT66121_AVIINFO_DB11_REG,
++ IT66121_AVIINFO_DB12_REG,
++ IT66121_AVIINFO_DB13_REG
++ };
++
++ mutex_lock(&ctx->lock);
++
++ hdmi_avi_infoframe_init(&ctx->hdmi_avi_infoframe);
++
++ ret = drm_hdmi_avi_infoframe_from_display_mode(&ctx->hdmi_avi_infoframe,
++ &ctx->connector,
++ adjusted_mode);
++ if (ret) {
++ DRM_ERROR("Failed to setup AVI infoframe: %d\n", ret);
++ goto unlock;
++ }
++
++ ret = hdmi_avi_infoframe_pack(&ctx->hdmi_avi_infoframe, buf,
++ sizeof(buf));
++ if (ret < 0) {
++ DRM_ERROR("Failed to pack infoframe: %d\n", ret);
++ goto unlock;
++ }
++
++ /* Write new AVI infoframe packet */
++ for (i = 0; i < HDMI_AVI_INFOFRAME_SIZE; i++) {
++ if (regmap_write(ctx->regmap, aviinfo_reg[i],
++ buf[i + HDMI_INFOFRAME_HEADER_SIZE]))
++ goto unlock;
++ }
++ if (regmap_write(ctx->regmap, IT66121_AVIINFO_CSUM_REG, buf[3]))
++ goto unlock;
++
++ /* Enable AVI infoframe */
++ if (regmap_write(ctx->regmap, IT66121_AVI_INFO_PKT_REG,
++ IT66121_AVI_INFO_PKT_ON |
++ IT66121_AVI_INFO_PKT_RPT))
++ goto unlock;
++
++ /* Set TX mode to HDMI */
++ if (regmap_write(ctx->regmap, IT66121_HDMI_MODE_REG,
++ IT66121_HDMI_MODE_HDMI))
++ goto unlock;
++
++ if (regmap_write_bits(ctx->regmap, IT66121_CLK_BANK_REG,
++ IT66121_CLK_BANK_PWROFF_TXCLK,
++ IT66121_CLK_BANK_PWROFF_TXCLK))
++ goto unlock;
++
++ if (it66121_configure_input(ctx))
++ goto unlock;
++
++ if (it66121_configure_afe(ctx, adjusted_mode))
++ goto unlock;
++
++ regmap_write_bits(ctx->regmap, IT66121_CLK_BANK_REG,
++ IT66121_CLK_BANK_PWROFF_TXCLK,
++ ~IT66121_CLK_BANK_PWROFF_TXCLK & 0xFF);
++
++unlock:
++ mutex_unlock(&ctx->lock);
++}
++
++static const struct drm_bridge_funcs it66121_bridge_funcs = {
++ .attach = it66121_bridge_attach,
++ .enable = it66121_bridge_enable,
++ .disable = it66121_bridge_disable,
++ .mode_set = it66121_bridge_mode_set,
++};
++
++static irqreturn_t it66121_irq_threaded_handler(int irq, void *dev_id)
++{
++ int ret;
++ unsigned int val;
++ struct it66121_ctx *ctx = dev_id;
++ struct device *dev = ctx->dev;
++ bool event = false;
++
++ mutex_lock(&ctx->lock);
++
++ ret = regmap_read(ctx->regmap, IT66121_SYS_STATUS_REG, &val);
++ if (ret)
++ goto unlock;
++
++ if (val & IT66121_SYS_STATUS_ACTIVE_IRQ) {
++ ret = regmap_read(ctx->regmap, IT66121_INT_STATUS1_REG, &val);
++ if (ret) {
++ dev_err(dev, "Cannot read STATUS1_REG %d\n", ret);
++ } else {
++ if (val & IT66121_INT_STATUS1_DDC_FIFOERR)
++ it66121_clear_ddc_fifo(ctx);
++ if (val & (IT66121_INT_STATUS1_DDC_BUSHANG |
++ IT66121_INT_STATUS1_DDC_NOACK))
++ it66121_abort_ddc_ops(ctx);
++ if (val & IT66121_INT_STATUS1_HPD_STATUS) {
++ regmap_write_bits(ctx->regmap,
++ IT66121_INT_CLR1_REG,
++ IT66121_INT_CLR1_HPD,
++ IT66121_INT_CLR1_HPD);
++
++ if (!it66121_is_hpd_detect(ctx)) {
++ kfree(ctx->edid);
++ ctx->edid = NULL;
++ }
++ event = true;
++ }
++ }
++
++ regmap_write_bits(ctx->regmap, IT66121_SYS_STATUS_REG,
++ IT66121_SYS_STATUS_CLEAR_IRQ,
++ IT66121_SYS_STATUS_CLEAR_IRQ);
++ }
++
++unlock:
++ mutex_unlock(&ctx->lock);
++
++ if (event)
++ drm_helper_hpd_irq_event(ctx->bridge.dev);
++
++ return IRQ_HANDLED;
++}
++
++static int it66121_probe(struct i2c_client *client,
++ const struct i2c_device_id *id)
++{
++ u8 ids[4];
++ int i, ret;
++ struct it66121_ctx *ctx;
++ struct device *dev = &client->dev;
++
++ if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
++ dev_err(dev, "I2C check functionality failed.\n");
++ return -ENXIO;
++ }
++
++ ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
++ if (!ctx)
++ return -ENOMEM;
++
++ ctx->dev = dev;
++ ctx->client = client;
++ i2c_set_clientdata(client, ctx);
++ mutex_init(&ctx->lock);
++ ctx->conf = (struct it66121_conf *)of_device_get_match_data(dev);
++ if (!ctx->conf)
++ return -ENODEV;
++
++ ctx->supplies[0].supply = "vcn33";
++ ctx->supplies[1].supply = "vcn18";
++ ctx->supplies[2].supply = "vrf12";
++ ret = devm_regulator_bulk_get(ctx->dev, 3, ctx->supplies);
++ if (ret) {
++ dev_err(ctx->dev, "regulator_bulk failed\n");
++ return ret;
++ }
++
++ ctx->dual_edge = of_property_read_bool(dev->of_node, "pclk-dual-edge");
++
++ ret = ite66121_power_on(ctx);
++ if (ret)
++ return ret;
++
++ it66121_hw_reset(ctx);
++
++ ctx->regmap = devm_regmap_init_i2c(client, &it66121_regmap_config);
++ if (IS_ERR(ctx->regmap)) {
++ ite66121_power_off(ctx);
++ return PTR_ERR(ctx);
++ }
++
++ for (i = 0; i < 4; i++) {
++ regmap_read(ctx->regmap, i, &ret);
++ ids[i] = ret;
++ }
++
++ if (ids[0] != IT66121_VENDOR_ID0 ||
++ ids[1] != IT66121_VENDOR_ID1 ||
++ ids[2] != IT66121_DEVICE_ID0 ||
++ ((ids[3] & IT66121_DEVICE_MASK) != IT66121_DEVICE_ID1)) {
++ ite66121_power_off(ctx);
++ return -ENODEV;
++ }
++
++ ctx->bridge.funcs = &it66121_bridge_funcs;
++ ctx->bridge.of_node = dev->of_node;
++
++ ret = devm_request_threaded_irq(dev, client->irq, NULL,
++ it66121_irq_threaded_handler,
++ IRQF_SHARED | IRQF_TRIGGER_LOW |
++ IRQF_ONESHOT,
++ dev_name(dev),
++ ctx);
++ if (ret < 0) {
++ dev_err(dev, "Failed to request irq %d:%d\n", client->irq, ret);
++ ite66121_power_off(ctx);
++ return ret;
++ }
++
++ drm_bridge_add(&ctx->bridge);
++
++ return 0;
++}
++
++static int it66121_remove(struct i2c_client *client)
++{
++ struct it66121_ctx *ctx = i2c_get_clientdata(client);
++
++ ite66121_power_off(ctx);
++ drm_bridge_remove(&ctx->bridge);
++ kfree(ctx->edid);
++ mutex_destroy(&ctx->lock);
++
++ return 0;
++}
++
++static const struct of_device_id it66121_dt_match[] = {
++ { .compatible = "ite,it66121",
++ .data = &it66121_conf_simple,
++ },
++ { },
++};
++MODULE_DEVICE_TABLE(of, it66121_dt_match);
++
++static const struct i2c_device_id it66121_id[] = {
++ { "it66121", 0 },
++ { },
++};
++MODULE_DEVICE_TABLE(i2c, it66121_id);
++
++static struct i2c_driver it66121_driver = {
++ .driver = {
++ .name = "it66121",
++ .of_match_table = it66121_dt_match,
++ },
++ .probe = it66121_probe,
++ .remove = it66121_remove,
++ .id_table = it66121_id,
++};
++
++module_i2c_driver(it66121_driver);
++
++MODULE_AUTHOR("Phong LE");
++MODULE_DESCRIPTION("IT66121 HDMI transmitter driver");
++MODULE_LICENSE("GPL v2");
+--
+2.25.1
+
diff --git a/board/olimex/stmp1_olinuxino/patches/linux/0002-more-display-olimex.patch b/board/olimex/stmp1_olinuxino/patches/linux/0002-more-display-olimex.patch
new file mode 100644
index 000000000..6353451e2
--- /dev/null
+++ b/board/olimex/stmp1_olinuxino/patches/linux/0002-more-display-olimex.patch
@@ -0,0 +1,175 @@
+From 54b934145102dc89c49d88761450e36cc9a1399d Mon Sep 17 00:00:00 2001
+From: Francois Perrad <francois.perrad@gadz.org>
+Date: Thu, 28 Oct 2021 20:32:51 +0200
+Subject: [PATCH] more display olimex
+
+fetched from https://github.com/OLIMEX/linux-olimex
+
+Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
+---
+ drivers/gpu/drm/panel/panel-simple.c | 131 ++++++++++++++++++++++++---
+ 1 file changed, 118 insertions(+), 13 deletions(-)
+
+diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
+index 204674fcc..2bec63ad0 100644
+--- a/drivers/gpu/drm/panel/panel-simple.c
++++ b/drivers/gpu/drm/panel/panel-simple.c
+@@ -2983,20 +2983,45 @@ static const struct panel_desc okaya_rs800480t_7x0gp = {
+ .bus_format = MEDIA_BUS_FMT_RGB666_1X18,
+ };
+
+-static const struct drm_display_mode olimex_lcd_olinuxino_43ts_mode = {
+- .clock = 9000,
++static const struct drm_display_mode olimex_vga_olinuxino_800_mode = {
++ .clock = 40000,
++ .hdisplay = 800,
++ .hsync_start = 800 + 40,
++ .hsync_end = 800 + 40 + 128,
++ .htotal = 800 + 40 + 128 + 88,
++ .vdisplay = 600,
++ .vsync_start = 600 + 5,
++ .vsync_end = 600 + 5 + 4,
++ .vtotal = 600 + 5 + 4 + 19,
++};
++
++static const struct drm_display_mode olimex_vga_olinuxino_1024_mode = {
++ .clock = 45000,
++ .hdisplay = 1024,
++ .hsync_start = 1024 + 16,
++ .hsync_end = 1024 + 16 + 10,
++ .htotal = 1024 + 16 + 10 + 150,
++ .vdisplay = 600,
++ .vsync_start = 600 + 2,
++ .vsync_end = 600 + 2 + 21,
++ .vtotal = 600 + 2 + 21 + 2,
++};
++
++
++static const struct drm_display_mode olimex_lcd_olinuxino_43_mode = {
++ .clock = 9530,
+ .hdisplay = 480,
+- .hsync_start = 480 + 5,
+- .hsync_end = 480 + 5 + 30,
+- .htotal = 480 + 5 + 30 + 10,
++ .hsync_start = 480 + 8,
++ .hsync_end = 480 + 8 + 20,
++ .htotal = 480 + 8 + 20 + 23,
+ .vdisplay = 272,
+- .vsync_start = 272 + 8,
+- .vsync_end = 272 + 8 + 5,
+- .vtotal = 272 + 8 + 5 + 3,
++ .vsync_start = 272 + 4,
++ .vsync_end = 272 + 4 + 10,
++ .vtotal = 272 + 4 + 10 + 13,
+ };
+
+-static const struct panel_desc olimex_lcd_olinuxino_43ts = {
+- .modes = &olimex_lcd_olinuxino_43ts_mode,
++static const struct panel_desc olimex_lcd_olinuxino_43 = {
++ .modes = &olimex_lcd_olinuxino_43_mode,
+ .num_modes = 1,
+ .size = {
+ .width = 95,
+@@ -3005,6 +3030,71 @@ static const struct panel_desc olimex_lcd_olinuxino_43ts = {
+ .bus_format = MEDIA_BUS_FMT_RGB888_1X24,
+ };
+
++static const struct drm_display_mode olimex_lcd_olinuxino_5_mode = {
++ .clock = 33300,
++ .hdisplay = 800,
++ .hsync_start = 800 + 210,
++ .hsync_end = 800 + 210 + 20,
++ .htotal = 800 + 210 + 20 + 26,
++ .vdisplay = 480,
++ .vsync_start = 480 + 22,
++ .vsync_end = 480 + 22 + 10,
++ .vtotal = 480 + 22 + 10 + 13,
++};
++
++static const struct panel_desc olimex_lcd_olinuxino_5 = {
++ .modes = &olimex_lcd_olinuxino_5_mode,
++ .num_modes = 1,
++ .size = {
++ .width = 154,
++ .height = 86,
++ },
++ .bus_format = MEDIA_BUS_FMT_RGB888_1X24,
++};
++static const struct drm_display_mode olimex_lcd_olinuxino_7_mode = {
++ .clock = 33300,
++ .hdisplay = 800,
++ .hsync_start = 800 + 210,
++ .hsync_end = 800 + 210 + 20,
++ .htotal = 800 + 210 + 20 + 26,
++ .vdisplay = 480,
++ .vsync_start = 480 + 22,
++ .vsync_end = 480 + 22 + 10,
++ .vtotal = 480 + 22 + 10 + 13,
++};
++
++static const struct panel_desc olimex_lcd_olinuxino_7 = {
++ .modes = &olimex_lcd_olinuxino_7_mode,
++ .num_modes = 1,
++ .size = {
++ .width = 154,
++ .height = 86,
++ },
++ .bus_format = MEDIA_BUS_FMT_RGB888_1X24,
++};
++
++static const struct drm_display_mode olimex_lcd_olinuxino_10_mode = {
++ .clock = 45000,
++ .hdisplay = 1024,
++ .hsync_start = 1024 + 16,
++ .hsync_end = 1024 + 16 + 1,
++ .htotal = 1024 + 10 + 6 + 160,
++ .vdisplay = 600,
++ .vsync_start = 600 + 1,
++ .vsync_end = 600 + 1 + 1,
++ .vtotal = 600 + 1 + 1 + 22,
++};
++
++static const struct panel_desc olimex_lcd_olinuxino_10 = {
++ .modes = &olimex_lcd_olinuxino_10_mode,
++ .num_modes = 1,
++ .size = {
++ .width = 222,
++ .height = 143,
++ },
++ .bus_format = MEDIA_BUS_FMT_RGB888_1X24,
++};
++
+ /*
+ * 800x480 CVT. The panel appears to be quite accepting, at least as far as
+ * pixel clocks, but this is the timing that was being used in the Adafruit
+@@ -4177,9 +4267,24 @@ static const struct of_device_id platform_of_match[] = {
+ }, {
+ .compatible = "okaya,rs800480t-7x0gp",
+ .data = &okaya_rs800480t_7x0gp,
+- }, {
+- .compatible = "olimex,lcd-olinuxino-43-ts",
+- .data = &olimex_lcd_olinuxino_43ts,
++ },{
++ .compatible = "olimex,olinuxino-vga-800x600",
++ .data = &olimex_vga_olinuxino_800_mode,
++ },{
++ .compatible = "olimex,olinuxino-vga-1024x768",
++ .data = &olimex_vga_olinuxino_1024_mode,
++ },{
++ .compatible = "olimex,lcd-olinuxino-4.3",
++ .data = &olimex_lcd_olinuxino_43,
++ }, {
++ .compatible = "olimex,lcd-olinuxino-5",
++ .data = &olimex_lcd_olinuxino_5,
++ }, {
++ .compatible = "olimex,lcd-olinuxino-7",
++ .data = &olimex_lcd_olinuxino_7,
++ }, {
++ .compatible = "olimex,lcd-olinuxino-10",
++ .data = &olimex_lcd_olinuxino_10,
+ }, {
+ .compatible = "ontat,yx700wv03",
+ .data = &ontat_yx700wv03,
+--
+2.25.1
+
diff --git a/board/olimex/stmp1_olinuxino/patches/uboot/0001-AXP-not-only-with-sunxi.patch b/board/olimex/stmp1_olinuxino/patches/uboot/0001-AXP-not-only-with-sunxi.patch
new file mode 100644
index 000000000..49251215a
--- /dev/null
+++ b/board/olimex/stmp1_olinuxino/patches/uboot/0001-AXP-not-only-with-sunxi.patch
@@ -0,0 +1,168 @@
+From 240af8affb9037b25f41749542d7cf6598760934 Mon Sep 17 00:00:00 2001
+From: Francois Perrad <francois.perrad@gadz.org>
+Date: Sun, 10 Oct 2021 16:32:39 +0200
+Subject: [PATCH 1/2] AXP not only with sunxi
+
+just move declarations from specific arch/mach sunxi to power
+
+Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
+---
+ arch/arm/mach-sunxi/Kconfig | 6 ------
+ arch/arm/mach-sunxi/pmic_bus.c | 2 +-
+ drivers/gpio/axp_gpio.c | 2 +-
+ drivers/power/Kconfig | 6 ++++++
+ drivers/power/axp152.c | 2 +-
+ drivers/power/axp209.c | 2 +-
+ drivers/power/axp221.c | 2 +-
+ drivers/power/axp305.c | 2 +-
+ drivers/power/axp809.c | 2 +-
+ drivers/power/axp818.c | 2 +-
+ .../arm/include/asm/arch-sunxi => include/power}/pmic_bus.h | 0
+ 11 files changed, 14 insertions(+), 14 deletions(-)
+ rename {arch/arm/include/asm/arch-sunxi => include/power}/pmic_bus.h (100%)
+
+diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
+index 49f94f095c..a4f71469f8 100644
+--- a/arch/arm/mach-sunxi/Kconfig
++++ b/arch/arm/mach-sunxi/Kconfig
+@@ -105,12 +105,6 @@ config SUN6I_PRCM
+ Support for the PRCM (Power/Reset/Clock Management) unit available
+ in A31 SoC.
+
+-config AXP_PMIC_BUS
+- bool "Sunxi AXP PMIC bus access helpers"
+- help
+- Select this PMIC bus access helpers for Sunxi platform PRCM or other
+- AXP family PMIC devices.
+-
+ config SUN8I_RSB
+ bool "Allwinner sunXi Reduced Serial Bus Driver"
+ help
+diff --git a/arch/arm/mach-sunxi/pmic_bus.c b/arch/arm/mach-sunxi/pmic_bus.c
+index 0394ce8564..c8ebbf5ee8 100644
+--- a/arch/arm/mach-sunxi/pmic_bus.c
++++ b/arch/arm/mach-sunxi/pmic_bus.c
+@@ -12,7 +12,7 @@
+ #include <asm/arch/p2wi.h>
+ #include <asm/arch/rsb.h>
+ #include <i2c.h>
+-#include <asm/arch/pmic_bus.h>
++#include <power/pmic_bus.h>
+
+ #define AXP152_I2C_ADDR 0x30
+
+diff --git a/drivers/gpio/axp_gpio.c b/drivers/gpio/axp_gpio.c
+index 73058cf40b..90bf4b84ff 100644
+--- a/drivers/gpio/axp_gpio.c
++++ b/drivers/gpio/axp_gpio.c
+@@ -7,7 +7,7 @@
+
+ #include <common.h>
+ #include <asm/arch/gpio.h>
+-#include <asm/arch/pmic_bus.h>
++#include <power/pmic_bus.h>
+ #include <asm/gpio.h>
+ #include <axp_pmic.h>
+ #include <dm.h>
+diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
+index c5fbf1f832..431e522771 100644
+--- a/drivers/power/Kconfig
++++ b/drivers/power/Kconfig
+@@ -8,6 +8,12 @@ source "drivers/power/pmic/Kconfig"
+
+ source "drivers/power/regulator/Kconfig"
+
++config AXP_PMIC_BUS
++ bool "Sunxi AXP PMIC bus access helpers"
++ help
++ Select this PMIC bus access helpers for Sunxi platform PRCM or other
++ AXP family PMIC devices.
++
+ choice
+ prompt "Select Sunxi PMIC Variant"
+ depends on ARCH_SUNXI
+diff --git a/drivers/power/axp152.c b/drivers/power/axp152.c
+index d6e36125c1..3eb60ce4ec 100644
+--- a/drivers/power/axp152.c
++++ b/drivers/power/axp152.c
+@@ -5,7 +5,7 @@
+ */
+ #include <common.h>
+ #include <command.h>
+-#include <asm/arch/pmic_bus.h>
++#include <power/pmic_bus.h>
+ #include <axp_pmic.h>
+
+ static u8 axp152_mvolt_to_target(int mvolt, int min, int max, int div)
+diff --git a/drivers/power/axp209.c b/drivers/power/axp209.c
+index ade531940b..6ab7aa5bf8 100644
+--- a/drivers/power/axp209.c
++++ b/drivers/power/axp209.c
+@@ -6,7 +6,7 @@
+
+ #include <common.h>
+ #include <command.h>
+-#include <asm/arch/pmic_bus.h>
++#include <power/pmic_bus.h>
+ #include <axp_pmic.h>
+ #include <linux/delay.h>
+
+diff --git a/drivers/power/axp221.c b/drivers/power/axp221.c
+index 3446fe7365..e35a876578 100644
+--- a/drivers/power/axp221.c
++++ b/drivers/power/axp221.c
+@@ -12,7 +12,7 @@
+ #include <common.h>
+ #include <command.h>
+ #include <errno.h>
+-#include <asm/arch/pmic_bus.h>
++#include <power/pmic_bus.h>
+ #include <axp_pmic.h>
+
+ static u8 axp221_mvolt_to_cfg(int mvolt, int min, int max, int div)
+diff --git a/drivers/power/axp305.c b/drivers/power/axp305.c
+index 0191e4d427..bfadea6e00 100644
+--- a/drivers/power/axp305.c
++++ b/drivers/power/axp305.c
+@@ -12,7 +12,7 @@
+ #include <common.h>
+ #include <command.h>
+ #include <errno.h>
+-#include <asm/arch/pmic_bus.h>
++#include <power/pmic_bus.h>
+ #include <axp_pmic.h>
+
+ #define AXP305_DCDC4_1600MV_OFFSET 46
+diff --git a/drivers/power/axp809.c b/drivers/power/axp809.c
+index 6323492b66..e438a13509 100644
+--- a/drivers/power/axp809.c
++++ b/drivers/power/axp809.c
+@@ -14,7 +14,7 @@
+ #include <command.h>
+ #include <errno.h>
+ #include <asm/arch/gpio.h>
+-#include <asm/arch/pmic_bus.h>
++#include <power/pmic_bus.h>
+ #include <axp_pmic.h>
+
+ static u8 axp809_mvolt_to_cfg(int mvolt, int min, int max, int div)
+diff --git a/drivers/power/axp818.c b/drivers/power/axp818.c
+index 0531707c8a..df69927c84 100644
+--- a/drivers/power/axp818.c
++++ b/drivers/power/axp818.c
+@@ -14,7 +14,7 @@
+ #include <command.h>
+ #include <errno.h>
+ #include <asm/arch/gpio.h>
+-#include <asm/arch/pmic_bus.h>
++#include <power/pmic_bus.h>
+ #include <axp_pmic.h>
+
+ static u8 axp818_mvolt_to_cfg(int mvolt, int min, int max, int div)
+diff --git a/arch/arm/include/asm/arch-sunxi/pmic_bus.h b/include/power/pmic_bus.h
+similarity index 100%
+rename from arch/arm/include/asm/arch-sunxi/pmic_bus.h
+rename to include/power/pmic_bus.h
+--
+2.30.2
+
diff --git a/board/olimex/stmp1_olinuxino/patches/uboot/0002-uses-AXP209-as-PMIC.patch b/board/olimex/stmp1_olinuxino/patches/uboot/0002-uses-AXP209-as-PMIC.patch
new file mode 100644
index 000000000..ca0dbc6b2
--- /dev/null
+++ b/board/olimex/stmp1_olinuxino/patches/uboot/0002-uses-AXP209-as-PMIC.patch
@@ -0,0 +1,205 @@
+From 76ea4a75aaea0640cf916d97df981d12b85772e5 Mon Sep 17 00:00:00 2001
+From: Francois Perrad <francois.perrad@gadz.org>
+Date: Tue, 12 Oct 2021 21:07:55 +0200
+Subject: [PATCH 2/2] uses AXP209 as PMIC
+
+Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
+---
+ arch/arm/mach-stm32mp/Makefile | 1 +
+ arch/arm/mach-stm32mp/pmic_bus.c | 83 +++++++++++++++++++++++++++
+ arch/arm/mach-stm32mp/pwr_regulator.c | 3 +-
+ board/st/stm32mp1/spl.c | 7 +++
+ drivers/phy/phy-stm32-usbphyc.c | 2 +
+ drivers/power/Kconfig | 4 +-
+ 6 files changed, 97 insertions(+), 3 deletions(-)
+ create mode 100644 arch/arm/mach-stm32mp/pmic_bus.c
+
+diff --git a/arch/arm/mach-stm32mp/Makefile b/arch/arm/mach-stm32mp/Makefile
+index 391b47cf13..c582591b7c 100644
+--- a/arch/arm/mach-stm32mp/Makefile
++++ b/arch/arm/mach-stm32mp/Makefile
+@@ -21,3 +21,4 @@ endif
+
+ obj-$(CONFIG_$(SPL_)DM_REGULATOR) += pwr_regulator.o
+ obj-$(CONFIG_OF_SYSTEM_SETUP) += fdt.o
++obj-$(CONFIG_AXP_PMIC_BUS) += pmic_bus.o
+diff --git a/arch/arm/mach-stm32mp/pmic_bus.c b/arch/arm/mach-stm32mp/pmic_bus.c
+new file mode 100644
+index 0000000000..f52d619af3
+--- /dev/null
++++ b/arch/arm/mach-stm32mp/pmic_bus.c
+@@ -0,0 +1,83 @@
++// SPDX-License-Identifier: GPL-2.0+
++/*
++ * (C) Copyright 2015 Hans de Goede <hdegoede@redhat.com>
++ *
++ * Sunxi PMIC bus access helpers
++ *
++ * The axp152 & axp209 use an i2c bus, the axp221 uses the p2wi bus and the
++ * axp223 uses the rsb bus, these functions abstract this.
++ */
++
++#include <common.h>
++#include <command.h>
++#include <i2c.h>
++#include <dm.h>
++#include <power/pmic_bus.h>
++
++#define AXP209_I2C_ADDR 0x34
++
++ struct udevice *dev;
++
++int pmic_bus_init(void)
++{
++ /* This cannot be 0 because it is used in SPL before BSS is ready */
++ static int needs_init = 1;
++ __maybe_unused int ret;
++ struct udevice *bus;
++
++ if (!needs_init)
++ return 0;
++
++ ret = uclass_get_device_by_seq(UCLASS_I2C, 0, &bus);
++ if (ret)
++ return ret;
++
++ ret = dm_i2c_probe(bus, AXP209_I2C_ADDR, 0, &dev);
++ if (ret)
++ return ret;
++
++ needs_init = 0;
++ return 0;
++}
++
++int pmic_bus_read(u8 reg, u8 *data)
++{
++ return dm_i2c_read(dev, reg, data, 1);
++}
++
++int pmic_bus_write(u8 reg, u8 data)
++{
++ return dm_i2c_write(dev,reg, &data,1);
++}
++
++int pmic_bus_setbits(u8 reg, u8 bits)
++{
++ int ret;
++ u8 val;
++
++ ret = pmic_bus_read(reg, &val);
++ if (ret)
++ return ret;
++
++ if ((val & bits) == bits)
++ return 0;
++
++ val |= bits;
++ return pmic_bus_write(reg, val);
++}
++
++int pmic_bus_clrbits(u8 reg, u8 bits)
++{
++ int ret;
++ u8 val;
++
++ ret = pmic_bus_read(reg, &val);
++ if (ret)
++ return ret;
++
++ if (!(val & bits))
++ return 0;
++
++ val &= ~bits;
++ return pmic_bus_write(reg, val);
++}
+diff --git a/arch/arm/mach-stm32mp/pwr_regulator.c b/arch/arm/mach-stm32mp/pwr_regulator.c
+index 846637ab16..71b2776a92 100644
+--- a/arch/arm/mach-stm32mp/pwr_regulator.c
++++ b/arch/arm/mach-stm32mp/pwr_regulator.c
+@@ -81,12 +81,13 @@ static const struct pmic_child_info pwr_children_info[] = {
+
+ static int stm32mp_pwr_bind(struct udevice *dev)
+ {
++#if defined(CONFIG_PMIC_STPMIC1)
+ int children;
+
+ children = pmic_bind_children(dev, dev_ofnode(dev), pwr_children_info);
+ if (!children)
+ dev_dbg(dev, "no child found\n");
+-
++#endif
+ return 0;
+ }
+
+diff --git a/board/st/stm32mp1/spl.c b/board/st/stm32mp1/spl.c
+index 8e4549a1b3..5fe09bf048 100644
+--- a/board/st/stm32mp1/spl.c
++++ b/board/st/stm32mp1/spl.c
+@@ -10,6 +10,7 @@
+ #include <asm/arch/sys_proto.h>
+ #include <linux/bitops.h>
+ #include <linux/delay.h>
++#include <axp_pmic.h>
+ #include "../common/stpmic1.h"
+
+ /* board early initialisation in board_f: need to use global variable */
+@@ -23,8 +24,14 @@ void board_vddcore_init(u32 voltage_mv)
+
+ int board_early_init_f(void)
+ {
++#if defined(CONFIG_AXP209_POWER)
++ axp_init();
++ axp_set_aldo3(1200);
++ axp_set_aldo2(3300);
++#else
+ if (IS_ENABLED(CONFIG_PMIC_STPMIC1) && CONFIG_IS_ENABLED(POWER))
+ stpmic1_init(opp_voltage_mv);
++#endif
+
+ return 0;
+ }
+diff --git a/drivers/phy/phy-stm32-usbphyc.c b/drivers/phy/phy-stm32-usbphyc.c
+index 02d859a039..15e6e1dd2b 100644
+--- a/drivers/phy/phy-stm32-usbphyc.c
++++ b/drivers/phy/phy-stm32-usbphyc.c
+@@ -364,6 +364,7 @@ static int stm32_usbphyc_probe(struct udevice *dev)
+ }
+
+ /* get usbphyc regulator */
++#if defined(CONFIG_PMIC_STPMIC1)
+ ret = device_get_supply_regulator(dev, "vdda1v1-supply",
+ &usbphyc->vdda1v1);
+ if (ret) {
+@@ -377,6 +378,7 @@ static int stm32_usbphyc_probe(struct udevice *dev)
+ dev_err(dev, "Can't get vdda1v8-supply regulator\n");
+ return ret;
+ }
++#endif
+
+ /*
+ * parse all PHY subnodes in order to populate regulator associated
+diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
+index 431e522771..85f5bdb7aa 100644
+--- a/drivers/power/Kconfig
++++ b/drivers/power/Kconfig
+@@ -16,7 +16,7 @@ config AXP_PMIC_BUS
+
+ choice
+ prompt "Select Sunxi PMIC Variant"
+- depends on ARCH_SUNXI
++ depends on ARCH_SUNXI || ARCH_STM32MP
+ default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
+ default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40
+ default AXP305_POWER if MACH_SUN50I_H616
+@@ -39,7 +39,7 @@ config AXP152_POWER
+
+ config AXP209_POWER
+ bool "axp209 pmic support"
+- depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I_V3S
++ depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I_V3S || TARGET_ST_STM32MP15x
+ select AXP_PMIC_BUS
+ select CMD_POWEROFF
+ ---help---
+--
+2.30.2
+
diff --git a/board/olimex/stmp1_olinuxino/patches/uboot/0003-add-ethaddr-in-u-boot-env.patch b/board/olimex/stmp1_olinuxino/patches/uboot/0003-add-ethaddr-in-u-boot-env.patch
new file mode 100644
index 000000000..a7bdc8644
--- /dev/null
+++ b/board/olimex/stmp1_olinuxino/patches/uboot/0003-add-ethaddr-in-u-boot-env.patch
@@ -0,0 +1,25 @@
+From f48ca38e84dc18dd3427c6cf10ec13adcbd25a9d Mon Sep 17 00:00:00 2001
+From: Francois Perrad <francois.perrad@gadz.org>
+Date: Wed, 13 Oct 2021 17:00:33 +0200
+Subject: [PATCH] add ethaddr in u-boot-env
+
+Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
+---
+ include/configs/stm32mp1.h | 1 +
+ 1 file changed, 1 insertion(+)
+
+diff --git a/include/configs/stm32mp1.h b/include/configs/stm32mp1.h
+index b372838be8..fc6d39dec2 100644
+--- a/include/configs/stm32mp1.h
++++ b/include/configs/stm32mp1.h
+@@ -159,6 +159,7 @@
+ * and the ramdisk at the end.
+ */
+ #define CONFIG_EXTRA_ENV_SETTINGS \
++ "ethaddr=00:12:34:56:00:00\0" \
+ "kernel_addr_r=0xc2000000\0" \
+ "fdt_addr_r=0xc4000000\0" \
+ "scriptaddr=0xc4100000\0" \
+--
+2.30.2
+
diff --git a/board/olimex/stmp1_olinuxino/readme.txt b/board/olimex/stmp1_olinuxino/readme.txt
new file mode 100644
index 000000000..8c641c6c8
--- /dev/null
+++ b/board/olimex/stmp1_olinuxino/readme.txt
@@ -0,0 +1,53 @@
+STMP157-OLinuXino-LIME2
+
+Intro
+=====
+
+These are open hardware boards, all based on the STmicro STMP157 SoC.
+
+for more details about the board see the following pages:
+ - https://www.olimex.com/Products/OLinuXino/open-source-hardware
+ - https://www.olimex.com/Products/OLinuXino/STMP1/STMP157-OLinuXino-LIME2/
+
+The following defconfigs are available:
+ - olimex_stmp157_olinuxino_lime_defconfig
+
+How to build it
+===============
+
+Configure Buildroot:
+
+ $ make <board>_defconfig
+
+Compile everything and build the rootfs image:
+
+ $ make
+
+Result of the build
+-------------------
+
+After building, you should get a tree like this:
+
+ output/images/
+ +-- rootfs.ext2
+ +-- rootfs.ext4 -> rootfs.ext2
+ +-- sdcard.img
+ +-- stm32mp1xx-olinuxino-lime.dtb
+ +-- u-boot-spl.stm32
+ +-- u-boot.img
+ `-- zImage
+
+
+How to write the SD card
+========================
+
+The sdcard.img file is a complete bootable image ready to be written
+on the boot medium. To install it, simply copy the image to a uSD
+card:
+
+ # dd if=output/images/sdcard.img of=/dev/sdX
+
+Where 'sdX' is the device node of the uSD.
+
+Eject the SD card, insert it in the STMP1-OLinuXino board, and power it up.
+
diff --git a/board/olimex/stmp1_olinuxino/rootfs_overlay/boot/extlinux/extlinux.conf b/board/olimex/stmp1_olinuxino/rootfs_overlay/boot/extlinux/extlinux.conf
new file mode 100644
index 000000000..edb601c7c
--- /dev/null
+++ b/board/olimex/stmp1_olinuxino/rootfs_overlay/boot/extlinux/extlinux.conf
@@ -0,0 +1,4 @@
+label stmp1-olinuxino-buildroot
+ kernel /boot/zImage
+ devicetree /boot/stm32mp1xx-olinuxino-lime.dtb
+ append root=/dev/mmcblk0p4 rootwait
diff --git a/board/olimex/stmp1_olinuxino/uboot-dts/stm32mp1-olinuxino-lime-u-boot.dtsi b/board/olimex/stmp1_olinuxino/uboot-dts/stm32mp1-olinuxino-lime-u-boot.dtsi
new file mode 100644
index 000000000..909530774
--- /dev/null
+++ b/board/olimex/stmp1_olinuxino/uboot-dts/stm32mp1-olinuxino-lime-u-boot.dtsi
@@ -0,0 +1,198 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright : STMicroelectronics 2018
+ */
+
+#include <dt-bindings/clock/stm32mp1-clksrc.h>
+#include "stm32mp15-u-boot.dtsi"
+#include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
+
+/ {
+ aliases {
+ mmc0 = &sdmmc1;
+ usb0 = &usbotg_hs;
+ };
+ config {
+ };
+};
+
+&clk_hse {
+ st,digbypass;
+};
+
+&i2c4 {
+ u-boot,dm-pre-reloc;
+};
+
+&i2c4_pins_a {
+ u-boot,dm-pre-reloc;
+ pins {
+ u-boot,dm-pre-reloc;
+ };
+};
+
+/*
+&pmic {
+ u-boot,dm-pre-reloc;
+};
+*/
+
+&rcc {
+ st,clksrc = <
+ CLK_MPU_PLL1P
+ CLK_AXI_PLL2P
+ CLK_MCU_PLL3P
+ CLK_PLL12_HSE
+ CLK_PLL3_HSE
+ CLK_PLL4_HSE
+ CLK_RTC_LSE
+ CLK_MCO1_DISABLED
+ CLK_MCO2_DISABLED
+ >;
+
+ st,clkdiv = <
+ 1 /*MPU*/
+ 0 /*AXI*/
+ 0 /*MCU*/
+ 1 /*APB1*/
+ 1 /*APB2*/
+ 1 /*APB3*/
+ 1 /*APB4*/
+ 2 /*APB5*/
+ 23 /*RTC*/
+ 0 /*MCO1*/
+ 0 /*MCO2*/
+ >;
+
+ st,pkcs = <
+ CLK_CKPER_HSE
+ CLK_FMC_ACLK
+ CLK_QSPI_ACLK
+ CLK_ETH_PLL4P
+ CLK_SDMMC12_PLL4P
+ CLK_DSI_DSIPLL
+ CLK_STGEN_HSE
+ CLK_USBPHY_HSE
+ CLK_SPI2S1_PLL3Q
+ CLK_SPI2S23_PLL3Q
+ CLK_SPI45_HSI
+ CLK_SPI6_HSI
+ CLK_I2C46_HSI
+ CLK_SDMMC3_PLL4P
+ CLK_USBO_USBPHY
+ CLK_ADC_CKPER
+ CLK_CEC_LSE
+ CLK_I2C12_HSI
+ CLK_I2C35_HSI
+ CLK_UART1_HSI
+ CLK_UART24_HSI
+ CLK_UART35_HSI
+ CLK_UART6_HSI
+ CLK_UART78_HSI
+ CLK_SPDIF_PLL4P
+ CLK_FDCAN_PLL4R
+ CLK_SAI1_PLL3Q
+ CLK_SAI2_PLL3Q
+ CLK_SAI3_PLL3Q
+ CLK_SAI4_PLL3Q
+ CLK_RNG1_LSI
+ CLK_RNG2_LSI
+ CLK_LPTIM1_PCLK1
+ CLK_LPTIM23_PCLK3
+ CLK_LPTIM45_LSE
+ >;
+
+ /* VCO = 1300.0 MHz => P = 650 (CPU) */
+ pll1: st,pll@0 {
+ compatible = "st,stm32mp1-pll";
+ reg = <0>;
+ cfg = < 2 80 0 0 0 PQR(1,0,0) >;
+ frac = < 0x800 >;
+ u-boot,dm-pre-reloc;
+ };
+
+ /* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
+ pll2: st,pll@1 {
+ compatible = "st,stm32mp1-pll";
+ reg = <1>;
+ cfg = < 2 65 1 0 0 PQR(1,1,1) >;
+ frac = < 0x1400 >;
+ u-boot,dm-pre-reloc;
+ };
+
+ /* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
+ pll3: st,pll@2 {
+ compatible = "st,stm32mp1-pll";
+ reg = <2>;
+ cfg = < 1 33 1 16 36 PQR(1,1,1) >;
+ frac = < 0x1a04 >;
+ u-boot,dm-pre-reloc;
+ };
+
+ /* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
+ pll4: st,pll@3 {
+ compatible = "st,stm32mp1-pll";
+ reg = <3>;
+ cfg = < 3 98 5 7 7 PQR(1,1,1) >;
+ u-boot,dm-pre-reloc;
+ };
+};
+
+&sdmmc1 {
+ u-boot,dm-spl;
+};
+
+&sdmmc1_b4_pins_a {
+ u-boot,dm-spl;
+ pins1 {
+ u-boot,dm-spl;
+ };
+ pins2 {
+ u-boot,dm-spl;
+ };
+};
+
+&sdmmc1_dir_pins_a {
+ u-boot,dm-spl;
+ pins1 {
+ u-boot,dm-spl;
+ };
+ pins2 {
+ u-boot,dm-spl;
+ };
+};
+
+&sdmmc2 {
+ u-boot,dm-spl;
+};
+
+&sdmmc2_b4_pins_a {
+ u-boot,dm-spl;
+ pins1 {
+ u-boot,dm-spl;
+ };
+ pins2 {
+ u-boot,dm-spl;
+ };
+};
+
+&sdmmc2_d47_pins_a {
+ u-boot,dm-spl;
+ pins {
+ u-boot,dm-spl;
+ };
+};
+
+&uart4 {
+ u-boot,dm-pre-reloc;
+};
+
+&uart4_pins_a {
+ u-boot,dm-pre-reloc;
+ pins1 {
+ u-boot,dm-pre-reloc;
+ };
+ pins2 {
+ u-boot,dm-pre-reloc;
+ };
+};
diff --git a/board/olimex/stmp1_olinuxino/uboot-dts/stm32mp1-olinuxino-lime.dts b/board/olimex/stmp1_olinuxino/uboot-dts/stm32mp1-olinuxino-lime.dts
new file mode 100644
index 000000000..fbac5d94f
--- /dev/null
+++ b/board/olimex/stmp1_olinuxino/uboot-dts/stm32mp1-olinuxino-lime.dts
@@ -0,0 +1,368 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
+ */
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+ model = "STM32MP1 OLinuXino-LIME";
+ compatible = "olimex,stm32mp1xx-olinuxino-lime", "st,stm32mp157";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@c0000000 {
+ device_type = "memory";
+ reg = <0xC0000000 0x40000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mcuram2: mcuram2@10000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10000000 0x40000>;
+ no-map;
+ };
+
+ vdev0vring0: vdev0vring0@10040000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10040000 0x1000>;
+ no-map;
+ };
+
+ vdev0vring1: vdev0vring1@10041000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10041000 0x1000>;
+ no-map;
+ };
+
+ vdev0buffer: vdev0buffer@10042000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10042000 0x4000>;
+ no-map;
+ };
+
+ mcuram: mcuram@30000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x30000000 0x40000>;
+ no-map;
+ };
+
+ retram: retram@38000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x38000000 0x10000>;
+ no-map;
+ };
+
+ gpu_reserved: gpu@e8000000 {
+ reg = <0xe8000000 0x8000000>;
+ no-map;
+ };
+ };
+
+ aliases {
+ serial0 = &uart4;
+ ethernet0 = ðernet0;
+ };
+
+ vdd_sd3v3: regulator_vdd {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ //regulator-over-current-protection;
+ };
+ vbus_otg: regulator_otg {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-otg";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ //regulator-over-current-protection;
+ };
+ vdd: vdd {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ //regulator-over-current-protection;
+ };
+ vdd_usb: vdd-usb {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ //regulator-over-current-protection;
+ };
+ vdd11: vdd11 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd11";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ //regulator-over-current-protection;
+ };
+ vdd18: vdd18 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ //regulator-over-current-protection;
+ };
+ reg_usb0_vbus: usb0-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb0-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ gpio = <&gpioc 6 GPIO_ACTIVE_HIGH>;
+ status = "disabled";
+ };
+ reg_usb1_vbus: usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ gpio = <&gpiof 15 GPIO_ACTIVE_HIGH>;
+ status = "disabled";
+ };
+};
+
+&dac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&dac_ch1_pins_a &dac_ch2_pins_a>;
+ status = "disabled";
+};
+
+&dts {
+ status = "okay";
+};
+
+&gpu {
+ contiguous-area = <&gpu_reserved>;
+ status = "okay";
+};
+
+®_usb0_vbus {
+ status="okay";
+};
+
+®_usb1_vbus {
+ status="okay";
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins_a>;
+// i2c-scl-rising-time-ns = <185>;
+// i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ pmic: stpmic@33 {
+ compatible = "st,stpmic1";
+ reg = <0x33>;
+ interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ status = "disabled";
+ };
+};
+
+&ipcc {
+ status = "okay";
+};
+
+&iwdg2 {
+ timeout-sec = <32>;
+ status = "okay";
+};
+
+&m4_rproc {
+ memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+ <&vdev0vring1>, <&vdev0buffer>;
+ mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+ mbox-names = "vq0", "vq1", "shutdown";
+ interrupt-parent = <&exti>;
+ interrupts = <68 1>;
+ status = "okay";
+};
+
+&pwr_regulators {
+ vdd-supply = <&vdd>;
+ vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&rng1 {
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
+ broken-cd;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&vdd_sd3v3>;
+ /*vqmmc-supply = <&sd_switch>;*/
+ status = "okay";
+};
+
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ st,neg-edge;
+ bus-width = <8>;
+ vmmc-supply = <&vdd_sd3v3>;
+ vqmmc-supply = <&vdd_sd3v3>;
+ mmc-ddr-3_3v;
+ status = "okay";
+};
+
+&timers6 {
+ status = "okay";
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ timer@5 {
+ status = "okay";
+ };
+};
+
+ðernet0 {
+ status = "okay";
+ pinctrl-0 = <ðernet0_rgmii_pins_a>;
+ pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rgmii-id";
+ phy-handle = <&phy1>;
+ st,eth_ref_clk_sel;
+ phy-reset-gpios = <&gpiod 10 GPIO_ACTIVE_LOW>;
+
+ mdio0 {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+ };
+};
+
+&m_can1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&m_can1_pins_a>;
+ pinctrl-1 = <&m_can1_sleep_pins_a>;
+ status = "okay";
+};
+
+&qspi {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
+ pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>;
+ reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ flash0: mx66l51235l@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins_a>;
+ status = "disabled";
+};
+
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_a>;
+ status = "okay";
+};
+
+
+&usbh_ehci {
+ phys = <&usbphyc_port0>;
+ phy-names = "usb";
+ status = "okay";
+};
+
+
+&usbotg_hs {
+ dr_mode = "peripheral";
+ phys = <&usbphyc_port1 0>;
+ phy-names = "usb2-phy";
+ vbus-supply = <&vbus_otg>;
+ status = "okay";
+};
+
+&usbphyc {
+ status = "okay";
+};
+
+&usbphyc_port0 {
+ phy-supply = <&vdd_usb>;
+ vdda1v1-supply = <&vdd11>;
+ vdda1v8-supply = <&vdd18>;
+
+};
+
+&usbphyc_port1 {
+ phy-supply = <&vdd_usb>;
+ vdda1v1-supply = <&vdd11>;
+ vdda1v8-supply = <&vdd18>;
+
+};
diff --git a/board/olimex/stmp1_olinuxino/uboot.fragment b/board/olimex/stmp1_olinuxino/uboot.fragment
new file mode 100644
index 000000000..2a97e6d9b
--- /dev/null
+++ b/board/olimex/stmp1_olinuxino/uboot.fragment
@@ -0,0 +1,16 @@
+
+# CONFIG_PMIC_STPMIC1 is not set
+# CONFIG_DM_REGULATOR_STPMIC1 is not set
+# CONFIG_SYSRESET_CMD_POWEROFF is not set
+CONFIG_AXP_PMIC_BUS=y
+CONFIG_AXP209_POWER=y
+
+# CONFIG_TYPEC_STUSB160X is not set
+
+# CONFIG_PHY_REALTEK is not set
+CONFIG_DM_MDIO=y
+CONFIG_PHY_MICREL=y
+CONFIG_PHY_MICREL_KSZ90X1=y
+
+# CONFIG_VIDEO_LCD_ORISETECH_OTM8009A is not set
+# CONFIG_VIDEO_LCD_RAYDIUM_RM68200 is not set
diff --git a/configs/olimex_stmp157_olinuxino_lime_defconfig b/configs/olimex_stmp157_olinuxino_lime_defconfig
new file mode 100644
index 000000000..3f1a3249e
--- /dev/null
+++ b/configs/olimex_stmp157_olinuxino_lime_defconfig
@@ -0,0 +1,51 @@
+# Architecture
+BR2_arm=y
+BR2_cortex_a7=y
+
+# Build options
+BR2_GLOBAL_PATCH_DIR="board/olimex/stmp1_olinuxino/patches"
+
+# Linux headers same as kernel, a 5.10 series
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_10=y
+
+# System configuration
+BR2_TARGET_GENERIC_HOSTNAME="stmp1-olinuxino"
+BR2_TARGET_GENERIC_ISSUE="Welcome to OLinuXino!"
+BR2_ROOTFS_OVERLAY="board/olimex/stmp1_olinuxino/rootfs_overlay"
+BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh"
+BR2_ROOTFS_POST_SCRIPT_ARGS="-c board/olimex/stmp1_olinuxino/genimage.cfg"
+
+# Kernel
+BR2_LINUX_KERNEL=y
+BR2_LINUX_KERNEL_CUSTOM_VERSION=y
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.10.70"
+BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
+BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/olimex/stmp1_olinuxino/linux.config"
+BR2_LINUX_KERNEL_DTS_SUPPORT=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="stm32mp1xx-olinuxino-lime"
+BR2_LINUX_KERNEL_CUSTOM_DTS_PATH="board/olimex/stmp1_olinuxino/linux-dts/*"
+BR2_LINUX_KERNEL_INSTALL_TARGET=y
+
+# Filesystem
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+# BR2_TARGET_ROOTFS_TAR is not set
+
+# Bootloaders
+BR2_TARGET_UBOOT=y
+BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
+BR2_TARGET_UBOOT_CUSTOM_VERSION=y
+BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2021.10"
+BR2_TARGET_UBOOT_BOARD_DEFCONFIG="stm32mp15_basic"
+BR2_TARGET_UBOOT_CONFIG_FRAGMENT_FILES="board/olimex/stmp1_olinuxino/uboot.fragment"
+BR2_TARGET_UBOOT_NEEDS_OPENSSL=y
+# BR2_TARGET_UBOOT_FORMAT_BIN is not set
+BR2_TARGET_UBOOT_FORMAT_IMG=y
+BR2_TARGET_UBOOT_FORMAT_STM32=y
+BR2_TARGET_UBOOT_SPL=y
+BR2_TARGET_UBOOT_SPL_NAME="spl/u-boot-spl.stm32"
+BR2_TARGET_UBOOT_CUSTOM_DTS_PATH="board/olimex/stmp1_olinuxino/uboot-dts/*"
+BR2_TARGET_UBOOT_CUSTOM_MAKEOPTS="dtb-y=stm32mp1-olinuxino-lime.dtb DEVICE_TREE=stm32mp1-olinuxino-lime"
+
+# Additional tools
+BR2_PACKAGE_HOST_GENIMAGE=y
--
2.32.0
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply related [flat|nested] 2+ messages in thread* Re: [Buildroot] [PATCH v2] board/olimex/stmp1_olinuxino: add STMP157-OLinuXino-LIME2 board support
2021-12-11 8:09 [Buildroot] [PATCH v2] board/olimex/stmp1_olinuxino: add STMP157-OLinuXino-LIME2 board support Francois Perrad
@ 2021-12-17 22:00 ` Thomas Petazzoni
0 siblings, 0 replies; 2+ messages in thread
From: Thomas Petazzoni @ 2021-12-17 22:00 UTC (permalink / raw)
To: Francois Perrad; +Cc: buildroot
Hello François,
On Sat, 11 Dec 2021 09:09:49 +0100
Francois Perrad <fperrad@gmail.com> wrote:
> kernel:
> - the device tree is not yet mainline
> - ITE IT66121 (HDMI) is mainline only since 5.14
>
> u-boot:
> - the device tree is not yet mainline
> - this board uses AXP209 as PMIC instead of the STPMIC1,
> this use case of AXP209 is not mainline
>
> arm-trusted-firmware:
> at this time, there is no patch for this board,
> so u-boot-spl is used as FSBL (basic boot chain)
Could we use the code from the Olimex Github repos instead? Your commit
really adds two many large board-specific patches. We try hard to avoid
this kind of stuff in Buildroot.
Also, I think the kernel config file shouldn't have comments. We pretty
much never do that with kernel configuration files as it's too annoying
to maintain.
Finally, your SoB line is missing.
Could you rework this?
Best regards,
Thomas
--
Thomas Petazzoni, co-owner and CEO, Bootlin
Embedded Linux and Kernel engineering and training
https://bootlin.com
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2021-12-17 22:00 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2021-12-11 8:09 [Buildroot] [PATCH v2] board/olimex/stmp1_olinuxino: add STMP157-OLinuXino-LIME2 board support Francois Perrad
2021-12-17 22:00 ` Thomas Petazzoni
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox