* [Buildroot] Buildroot How-To for QEMU/ARM
@ 2010-01-27 15:28 Jim Thomas
2010-01-27 16:10 ` Grant Edwards
0 siblings, 1 reply; 4+ messages in thread
From: Jim Thomas @ 2010-01-27 15:28 UTC (permalink / raw)
To: buildroot
Hello,
?
I can build qemu-0.12.2 under Ubuntu 9.10 and boot Linux in QEMU using the pre-built kernel and RFS in arm-test-0.2, also from the QEMU project.
?
Now I want to use QEMU to boot a Linux kernel and RFS that I built myself for ARM using buildroot-2009.11.
?
I have not had much luck. Based on web searching, I have tried twisting knobs in 'make menuconfig' and rebuilt perhaps a couple of dozen times.
?
Rather than do a core dump here of the details, I thought I would ask:
?
Has anyone used buildroot-2009.11 to build a kernel and RFS for ARM that boot successfully under qemu-0.12.2?
?
Do step-by-step notes exist for how to do this for ARM that were written for these latest versions of Buildroot and QEMU, or that have been verified as still complete and correct?
?
Ultimately, I might like to get Buildroot/QEMU working for a particular ARM processor, but for now, a working configuration for any virtualized ARM target is good enough.
?
A general purpose Buildroot/QEMU howto for ARM might serve as both a worthwhile regression test, and primary support document visible at the Buildroot web site.
?
Thanks.
?
Jim
^ permalink raw reply [flat|nested] 4+ messages in thread* [Buildroot] Buildroot How-To for QEMU/ARM
2010-01-27 15:28 [Buildroot] Buildroot How-To for QEMU/ARM Jim Thomas
@ 2010-01-27 16:10 ` Grant Edwards
2010-01-30 16:58 ` Jim Thomas
0 siblings, 1 reply; 4+ messages in thread
From: Grant Edwards @ 2010-01-27 16:10 UTC (permalink / raw)
To: buildroot
On 2010-01-27, Jim Thomas <jimthomasembedded@yahoo.com> wrote:
> Hello,
>
> I can build qemu-0.12.2 under Ubuntu 9.10 and boot Linux in
> QEMU using the pre-built kernel and RFS in arm-test-0.2, also
> from the QEMU project.
>
> Now I want to use QEMU to boot a Linux kernel and RFS that I
> built myself for ARM using buildroot-2009.11.
>
> I have not had much luck. Based on web searching, I have tried
> twisting knobs in 'make menuconfig' and rebuilt perhaps a
> couple of dozen times.
>
> Rather than do a core dump here of the details, I thought I
> would ask:
>
> Has anyone used buildroot-2009.11 to build a kernel and RFS
> for ARM that boot successfully under qemu-0.12.2?
I built for arm-integrator using HEAD back in
November/December, and it ran fine on qemu-0.9.1. I didn't do
much with it other than boot it up, log in, and test the
virtual serial ports.
> Do step-by-step notes exist for how to do this for ARM that
> were written for these latest versions of Buildroot and QEMU,
> or that have been verified as still complete and correct?
Not that I've found. There were some articles written a couple
years ago that have step-by-step instructions, but they're
missing a step or two and are also now out of date in a few
spots.
Here's the .config file I last used -- AFAIR it was working at
that point:
# Automatically generated make config: don't edit
# Wed Dec 16 09:10:07 2009
#
BR2_HAVE_DOT_CONFIG=y
BR2_VERSION="2009.11-git"
# BR2_alpha is not set
BR2_arm=y
# BR2_armeb is not set
# BR2_avr32 is not set
# BR2_cris is not set
# BR2_ia64 is not set
# BR2_i386 is not set
# BR2_m68k is not set
# BR2_mips is not set
# BR2_mipsel is not set
# BR2_nios2 is not set
# BR2_powerpc is not set
# BR2_sh is not set
# BR2_sh64 is not set
# BR2_sparc is not set
# BR2_sparc64 is not set
# BR2_x86_64 is not set
# BR2_xtensa is not set
# BR2_generic_arm is not set
# BR2_arm7tdmi is not set
# BR2_arm610 is not set
# BR2_arm710 is not set
# BR2_arm720t is not set
# BR2_arm920t is not set
# BR2_arm922t is not set
BR2_arm926t=y
# BR2_arm10t is not set
# BR2_arm1136jf_s is not set
# BR2_arm1176jz_s is not set
# BR2_arm1176jzf_s is not set
#
# cortex-A8 needs gcc >= 4.4.x
#
# BR2_cortex_a8 is not set
# BR2_sa110 is not set
# BR2_sa1100 is not set
# BR2_xscale is not set
# BR2_iwmmxt is not set
BR2_ARM_TYPE="ARM926T"
BR2_ARM_EABI=y
# BR2_ARM_OABI is not set
BR2_ARCH="arm"
BR2_ENDIAN="LITTLE"
BR2_GCC_TARGET_TUNE="arm9tdmi"
BR2_GCC_TARGET_ARCH="armv5te"
BR2_GCC_TARGET_ABI="aapcs-linux"
#
# Target options
#
#
# Preset Devices
#
BR2_TARGET_ARMLTD=y
#
# ARM Ltd. based Device Support
#
BR2_TARGET_ARM_INTEGRATOR_926=y
# BR2_TARGET_ARM_INTEGRATOR_926_HUGE is not set
BR2_BOARD_NAME="integrator926"
BR2_BOARD_PATH="target/device/ARMLTD/$(BR2_BOARD_NAME)"
# BR2_TARGET_ATMEL is not set
# BR2_TARGET_KWIKBYTE is not set
#
# Generic System Support
#
# BR2_TARGET_GENERIC_ACCESS_POINT is not set
# BR2_TARGET_GENERIC_FIREWALL is not set
#
# Generic development system requires a toolchain with WCHAR and PROGRAM_INVOCATION support
#
BR2_TARGET_GENERIC_HOSTNAME="buildroot"
BR2_TARGET_GENERIC_ISSUE="Welcome to Buildroot"
# BR2_TARGET_GENERIC_GETTY is not set
#
# Build options
#
BR2_WGET="wget --passive-ftp -nd"
BR2_SVN_CO="svn co"
BR2_SVN_UP="svn up"
BR2_BZR_CO="bzr co"
BR2_BZR_UP="bzr up"
BR2_GIT="git clone"
BR2_ZCAT="gzip -d -c"
BR2_BZCAT="bzcat"
BR2_TAR_OPTIONS=""
BR2_DL_DIR="$(TOPDIR)/dl"
BR2_COPYTO=""
#
# Mirrors and Download locations
#
BR2_PRIMARY_SITE=""
BR2_BACKUP_SITE="http://buildroot.net/downloads/sources/"
BR2_SOURCEFORGE_MIRROR="switch"
BR2_KERNEL_MIRROR="http://www.kernel.org/pub/"
BR2_GNU_MIRROR="http://ftp.gnu.org/pub/gnu"
BR2_DEBIAN_MIRROR="http://ftp.debian.org"
BR2_STAGING_DIR="$(BUILD_DIR)/staging_dir"
BR2_GNU_BUILD_SUFFIX="pc-linux-gnu"
BR2_GNU_TARGET_SUFFIX="linux-uclibcgnueabi"
BR2_JLEVEL=1
# BR2_PREFER_IMA is not set
# BR2_DEPRECATED is not set
BR2_RECENT=y
# BR2_CONFIG_CACHE is not set
# BR2_ENABLE_DEBUG is not set
BR2_STRIP_strip=y
# BR2_STRIP_sstrip is not set
# BR2_STRIP_none is not set
# BR2_OPTIMIZE_0 is not set
# BR2_OPTIMIZE_1 is not set
# BR2_OPTIMIZE_2 is not set
# BR2_OPTIMIZE_3 is not set
BR2_OPTIMIZE_S=y
# BR2_PREFER_STATIC_LIB is not set
# BR2_HAVE_MANPAGES is not set
# BR2_HAVE_INFOPAGES is not set
# BR2_HAVE_DOCUMENTATION is not set
# BR2_HAVE_DEVFILES is not set
BR2_UPDATE_CONFIG=y
#
# Toolchain
#
BR2_TOOLCHAIN_BUILDROOT=y
# BR2_TOOLCHAIN_EXTERNAL is not set
# BR2_TOOLCHAIN_EXTERNAL_SOURCE is not set
BR2_TOOLCHAIN_SOURCE=y
BR2_EXT_GCC_VERSION_4_1_2=y
BR2_EXT_GCC_VERSION_4_2_1=y
BR2_EXT_GCC_VERSION_4_2_2=y
BR2_EXT_GCC_VERSION_4_2_3=y
BR2_EXT_BINUTILS_VERSION_2_17=y
BR2_EXT_BINUTILS_VERSION_2_18=y
BR2_EXT_UCLIBC_VERSION_0_9_28_3=y
BR2_EXT_UCLIBC_VERSION_0_9_29=y
BR2_EXT_UCLIBC_VERSION_0_9_30=y
BR2_EXT_UCLIBC_VERSION_0_9_30_1=y
#
# Kernel Header Options
#
# BR2_KERNEL_HEADERS_2_6_26 is not set
# BR2_KERNEL_HEADERS_2_6_27 is not set
# BR2_KERNEL_HEADERS_2_6_28 is not set
# BR2_KERNEL_HEADERS_2_6_29 is not set
# BR2_KERNEL_HEADERS_2_6_30 is not set
BR2_KERNEL_HEADERS_2_6_31=y
# BR2_KERNEL_HEADERS_VERSION is not set
# BR2_KERNEL_HEADERS_SNAP is not set
BR2_DEFAULT_KERNEL_HEADERS="2.6.31.6"
#
# uClibc Options
#
# BR2_UCLIBC_VERSION_0_9_28_3 is not set
# BR2_UCLIBC_VERSION_0_9_29 is not set
BR2_UCLIBC_VERSION_0_9_30=y
# BR2_UCLIBC_VERSION_0_9_30_1 is not set
# BR2_UCLIBC_VERSION_SNAPSHOT is not set
BR2_UCLIBC_VERSION_STRING="0.9.30"
BR2_UCLIBC_CONFIG="target/device/ARMLTD/uClibc.integrator926.config"
# BR2_PTHREAD_DEBUG is not set
# BR2_UCLIBC_INSTALL_TEST_SUITE is not set
#
# Binutils Options
#
# BR2_BINUTILS_VERSION_2_17 is not set
# BR2_BINUTILS_VERSION_2_17_50_0_17 is not set
# BR2_BINUTILS_VERSION_2_18 is not set
# BR2_BINUTILS_VERSION_2_18_50_0_1 is not set
# BR2_BINUTILS_VERSION_2_18_50_0_3 is not set
# BR2_BINUTILS_VERSION_2_18_50_0_6 is not set
# BR2_BINUTILS_VERSION_2_18_50_0_8 is not set
# BR2_BINUTILS_VERSION_2_18_50_0_9 is not set
BR2_BINUTILS_VERSION_2_19=y
# BR2_BINUTILS_VERSION_2_19_1 is not set
BR2_BINUTILS_VERSION="2.19"
BR2_EXTRA_BINUTILS_CONFIG_OPTIONS=""
#
# GCC Options
#
# BR2_GCC_VERSION_4_1_2 is not set
# BR2_GCC_VERSION_4_2_1 is not set
# BR2_GCC_VERSION_4_2_2 is not set
# BR2_GCC_VERSION_4_2_3 is not set
# BR2_GCC_VERSION_4_2_4 is not set
# BR2_GCC_VERSION_4_3_2 is not set
# BR2_GCC_VERSION_4_3_3 is not set
BR2_GCC_VERSION_4_3_4=y
# BR2_GCC_VERSION_4_4_X is not set
BR2_GCC_SUPPORTS_SYSROOT=y
BR2_GCC_SUPPORTS_FINEGRAINEDMTUNE=y
BR2_GCC_VERSION="4.3.4"
BR2_TOOLCHAIN_SYSROOT=y
# BR2_GCC_USE_SJLJ_EXCEPTIONS is not set
BR2_EXTRA_GCC_CONFIG_OPTIONS=""
# BR2_GCC_CROSS_FORTRAN is not set
# BR2_INSTALL_OBJC is not set
# BR2_INSTALL_FORTRAN is not set
BR2_GCC_SHARED_LIBGCC=y
BR2_GCC_ENABLE_TLS=y
#
# Ccache Options
#
# BR2_CCACHE is not set
#
# Gdb Options
#
# BR2_PACKAGE_GDB is not set
# BR2_PACKAGE_GDB_SERVER is not set
# BR2_PACKAGE_GDB_HOST is not set
#
# Common Toolchain Options
#
# BR2_LARGEFILE is not set
# BR2_INET_IPV6 is not set
# BR2_INET_RPC is not set
# BR2_ENABLE_LOCALE is not set
# BR2_ENABLE_LOCALE_PURGE is not set
# BR2_USE_WCHAR is not set
BR2_PREFER_SOFT_FLOAT=y
BR2_SOFT_FLOAT=y
# BR2_USE_SSP is not set
# BR2_PTHREADS_NONE is not set
# BR2_PTHREADS is not set
BR2_PTHREADS_OLD=y
# BR2_PTHREADS_NATIVE is not set
# BR2_PROGRAM_INVOCATION is not set
# BR2_INSTALL_LIBSTDCPP is not set
BR2_TARGET_OPTIMIZATION="-Os -pipe -fwrapv"
# BR2_ELF2FLT is not set
# BR2_MKLIBS is not set
# BR2_PACKAGE_SSTRIP_TARGET is not set
# BR2_PACKAGE_SSTRIP_HOST is not set
# BR2_ENABLE_MULTILIB is not set
BR2_CROSS_TOOLCHAIN_TARGET_UTILS=y
#
# Package Selection for the target
#
BR2_PACKAGE_BUSYBOX=y
# BR2_BUSYBOX_VERSION_1_12_X is not set
BR2_BUSYBOX_VERSION_1_13_X=y
# BR2_BUSYBOX_VERSION_1_14_X is not set
# BR2_BUSYBOX_VERSION_1_15_X is not set
# BR2_PACKAGE_BUSYBOX_SNAPSHOT is not set
BR2_BUSYBOX_VERSION="1.13.4"
BR2_PACKAGE_BUSYBOX_FULLINSTALL=y
BR2_PACKAGE_BUSYBOX_CONFIG="package/busybox/busybox-1.13.x.config"
# BR2_PACKAGE_BUSYBOX_SHOW_OTHERS is not set
BR2_PACKAGE_BUSYBOX_SKELETON=y
#
# The minimum needed to build a uClibc development system
#
# BR2_PACKAGE_FLEX is not set
# BR2_PACKAGE_GCC_TARGET is not set
# BR2_PACKAGE_MAKE is not set
#
# Other development stuff
#
# BR2_PACKAGE_AUTOCONF is not set
# BR2_PACKAGE_AUTOMAKE is not set
# BR2_PACKAGE_BISON is not set
# BR2_PACKAGE_CCACHE_TARGET is not set
# BR2_PACKAGE_DISTCC is not set
# BR2_PACKAGE_DMALLOC is not set
# BR2_PACKAGE_FAKEROOT is not set
BR2_HOST_FAKEROOT=y
# BR2_PACKAGE_GETTEXT is not set
# BR2_PACKAGE_LIBINTL is not set
# BR2_PACKAGE_LIBGMP is not set
# BR2_PACKAGE_GPERF is not set
# BR2_PACKAGE_LIBMPFR is not set
# BR2_PACKAGE_LIBTOOL is not set
# BR2_PACKAGE_M4 is not set
#
# oprofile requires a toolchain with C++ support enabled
#
# BR2_PACKAGE_PKG_CONFIG is not set
# BR2_PACKAGE_READLINE is not set
# BR2_PACKAGE_PCRE is not set
#
# Other stuff
#
# BR2_PACKAGE_AT is not set
# BR2_PACKAGE_BEECRYPT is not set
# BR2_PACKAGE_BERKELEYDB is not set
# BR2_PACKAGE_BSDIFF is not set
# BR2_PACKAGE_CUPS is not set
# BR2_PACKAGE_CUSTOMIZE is not set
# BR2_PACKAGE_FILE is not set
# BR2_PACKAGE_GAMIN is not set
#
# icu requires a toolchain with C++ support and WCHAR enabled
#
# BR2_PACKAGE_KEXEC is not set
# BR2_PACKAGE_LIBCONFIG is not set
# BR2_PACKAGE_LIBCONFUSE is not set
# BR2_PACKAGE_LIBDAEMON is not set
# BR2_PACKAGE_LIBELF is not set
# BR2_PACKAGE_LIBEVENT is not set
# BR2_PACKAGE_LIBGCRYPT is not set
# BR2_PACKAGE_LIBGPG_ERROR is not set
# BR2_PACKAGE_LIBICONV is not set
# BR2_PACKAGE_LIBIDN is not set
# BR2_PACKAGE_LIBLOCKFILE is not set
# BR2_PACKAGE_LIBOIL is not set
# BR2_PACKAGE_LIBSYSFS is not set
# BR2_PACKAGE_LOCKFILE_PROGS is not set
#
# logrotate - disabled (requires wchar support)
#
# BR2_PACKAGE_LSOF is not set
# BR2_PACKAGE_LTP-TESTSUITE is not set
# BR2_PACKAGE_LTRACE is not set
# BR2_PACKAGE_MEMSTAT is not set
# BR2_PACKAGE_NG_SPICE_REWORK is not set
# BR2_PACKAGE_POPT is not set
# BR2_PACKAGE_SCREEN is not set
# BR2_PACKAGE_SHARED_MIME_INFO is not set
# BR2_PACKAGE_STARTUP_NOTIFICATION is not set
# BR2_PACKAGE_STRACE is not set
# BR2_PACKAGE_SUDO is not set
#
# Database
#
#
# Mysql client requires a toolchain with C++ support enabled
#
# BR2_PACKAGE_SQLITE is not set
#
# Text editors
#
# BR2_PACKAGE_ED is not set
# BR2_PACKAGE_NANO is not set
# BR2_PACKAGE_UEMACS is not set
#
# Networking
#
#
# Networking applications
#
# BR2_PACKAGE_ARGUS is not set
# BR2_PACKAGE_AVAHI is not set
# BR2_PACKAGE_AXEL is not set
#
# bind requires a toolchain with LARGEFILE support
#
# BR2_PACKAGE_BMON is not set
# BR2_PACKAGE_BRIDGE is not set
#
# ctorrent requires a toolchain with C++ support enabled
#
# BR2_PACKAGE_DNSMASQ is not set
# BR2_PACKAGE_DROPBEAR is not set
# BR2_PACKAGE_ETHTOOL is not set
# BR2_PACKAGE_HASERL is not set
# BR2_PACKAGE_IFPLUGD is not set
#
# iperf requires a toolchain with C++ support enabled
#
#
# iproute2 requires a toolchain with IPv6 support
#
# BR2_PACKAGE_IPSEC_TOOLS is not set
#
# iptables requires a toolchain with LARGEFILE support
#
# BR2_PACKAGE_IW is not set
#
# Kismet requires a toolchain with C++ support enabled
#
# BR2_PACKAGE_L2TP is not set
# BR2_PACKAGE_LIBCGI is not set
#
# libcgicc requires a toolchain with C++ support enabled
#
# BR2_PACKAGE_LIBCURL is not set
# BR2_PACKAGE_LIBDNET is not set
# BR2_PACKAGE_LIBEXOSIP2 is not set
# BR2_PACKAGE_LIBMICROHTTPD is not set
# BR2_PACKAGE_LIBNL is not set
# BR2_PACKAGE_LIBOSIP2 is not set
BR2_PACKAGE_LIBPCAP=y
# BR2_PACKAGE_LIBSOUP is not set
#
# libupnp requires a toolchain with LARGEFILE support
#
# BR2_PACKAGE_LINKS is not set
# BR2_PACKAGE_LRZSZ is not set
# BR2_PACKAGE_MIIDIAG is not set
# BR2_PACKAGE_MROUTED is not set
# BR2_PACKAGE_MUTT is not set
# BR2_PACKAGE_NBD is not set
#
# ncftp requires a toolchain with LARGEFILE support
#
# BR2_PACKAGE_NEON is not set
# BR2_PACKAGE_NETPLUG is not set
# BR2_PACKAGE_NETSNMP is not set
# BR2_PACKAGE_NETSTAT_NAT is not set
#
# nfs-utils requires a toolchain with 'Enable RPC' selected
#
# BR2_PACKAGE_NTP is not set
# BR2_PACKAGE_OLSR is not set
# BR2_PACKAGE_OPENNTPD is not set
BR2_PACKAGE_OPENSSH=y
BR2_PACKAGE_OPENSSL=y
# BR2_PACKAGE_OPENSSL_BIN is not set
# BR2_PACKAGE_OPENSSL_ENGINES is not set
# BR2_PACKAGE_OPENVPN is not set
#
# portmap requires a toolchain with 'Enable RPC' selected
#
# BR2_PACKAGE_PPPD is not set
# BR2_PACKAGE_RP_PPPOE is not set
# BR2_PACKAGE_PPTP_LINUX is not set
# BR2_PACKAGE_PROFTPD is not set
# BR2_PACKAGE_QUAGGA is not set
# BR2_PACKAGE_RSYNC is not set
# BR2_PACKAGE_SAMBA is not set
# BR2_PACKAGE_SOCAT is not set
# BR2_PACKAGE_SPAWN_FCGI is not set
# BR2_PACKAGE_STUNNEL is not set
BR2_PACKAGE_TCPDUMP=y
# BR2_PACKAGE_TCPDUMP_SMB is not set
# BR2_PACKAGE_DHCPDUMP is not set
# BR2_PACKAGE_TN5250 is not set
# BR2_PACKAGE_TTCP is not set
# BR2_PACKAGE_UDPCAST is not set
# BR2_PACKAGE_VPNC is not set
# BR2_PACKAGE_VSFTPD is not set
# BR2_PACKAGE_VTUN is not set
# BR2_PACKAGE_WEBIF is not set
# BR2_PACKAGE_WIRELESS_TOOLS is not set
# BR2_PACKAGE_WPA_SUPPLICANT is not set
#
# Hardware handling / blockdevices and filesystem maintenance
#
#
# dbus not available (need expat or libxml2)
#
#
# dmraid requires a toolchain with LARGEFILE support
#
# BR2_PACKAGE_DOSFSTOOLS is not set
#
# e2fsprogs requires a toolchain with LARGEFILE support
#
# BR2_PACKAGE_EEPROG is not set
# BR2_PACKAGE_FCONFIG is not set
# BR2_PACKAGE_FIS is not set
#
# libfuse requires a toolchain with LARGEFILE support
#
# BR2_PACKAGE_GADGETFS_TEST is not set
#
# gvfs requires a toolchain with LARGEFILE support
#
# BR2_PACKAGE_HAL is not set
# BR2_PACKAGE_HWDATA is not set
# BR2_PACKAGE_I2C_TOOLS is not set
# BR2_PACKAGE_INPUT_TOOLS is not set
# BR2_PACKAGE_IOSTAT is not set
# BR2_PACKAGE_LIBAIO is not set
# BR2_PACKAGE_LIBRAW1394 is not set
# BR2_PACKAGE_LIBUSB is not set
# BR2_PACKAGE_LM_SENSORS is not set
#
# lvm2 requires a toolchain with LARGEFILE support
#
# BR2_PACKAGE_MDADM is not set
# BR2_PACKAGE_MEMTESTER is not set
# BR2_PACKAGE_MTD is not set
#
# ntfs-3g requires a toolchain with LARGEFILE and WCHAR support
#
#
# ntfsprogs requires a toolchain with WCHAR support
#
BR2_PACKAGE_PCIUTILS=y
# BR2_PACKAGE_PCMCIA is not set
# BR2_PACKAGE_SETSERIAL is not set
# BR2_PACKAGE_SMARTMONTOOLS is not set
# BR2_PACKAGE_SYSSTAT is not set
# BR2_PACKAGE_USB_MODESWITCH is not set
# BR2_PACKAGE_USBMOUNT is not set
# BR2_PACKAGE_USBUTILS is not set
# BR2_PACKAGE_WIPE is not set
# BR2_PACKAGE_XFSPROGS is not set
#
# Audio and video libraries and applications
#
# BR2_PACKAGE_ALSA_LIB is not set
#
# alsa-utils requires a toolchain with LARGEFILE support
#
#
# asterisk - disabled (required openssl and mpg123)
#
# BR2_PACKAGE_AUMIX is not set
# BR2_PACKAGE_FLAC is not set
# BR2_PACKAGE_GSTREAMER is not set
# BR2_PACKAGE_LIBID3TAG is not set
# BR2_PACKAGE_LIBMAD is not set
# BR2_PACKAGE_LIBMMS is not set
# BR2_PACKAGE_LIBMPD is not set
# BR2_PACKAGE_LIBOGG is not set
# BR2_PACKAGE_LIBSNDFILE is not set
# BR2_PACKAGE_LIBTHEORA is not set
# BR2_PACKAGE_LIBVORBIS is not set
# BR2_PACKAGE_MADPLAY is not set
# BR2_PACKAGE_MPG123 is not set
# BR2_PACKAGE_MPLAYER is not set
# BR2_PACKAGE_SPEEX is not set
# BR2_PACKAGE_SWFDEC is not set
#
# festival requires a toolchain with C++ support enabled
#
#
# taglib requires a toolchain with C++ support enabled
#
# BR2_PACKAGE_VLC is not set
#
# Graphic libraries and applications (graphic/text)
#
#
# text rendering libraries
#
# BR2_PACKAGE_NCURSES is not set
# BR2_PACKAGE_NEWT is not set
# BR2_PACKAGE_SLANG is not set
#
# text rendering applications
#
# BR2_PACKAGE_DIALOG is not set
#
# graphic libraries
#
# BR2_PACKAGE_DIRECTFB is not set
# BR2_PACKAGE_FBDUMP is not set
# BR2_PACKAGE_IMAGEMAGICK is not set
# BR2_PACKAGE_JPEG is not set
# BR2_PACKAGE_LIBART is not set
# BR2_PACKAGE_LIBPNG is not set
# BR2_PACKAGE_LIBUNGIF is not set
# BR2_PACKAGE_LINUX_FUSION is not set
# BR2_PACKAGE_PIXMAN is not set
# BR2_PACKAGE_SDL is not set
# BR2_PACKAGE_TIFF is not set
#
# busybox graphic applications
#
#
# --> May be broken in busybox
#
# BR2_PACKAGE_FBV is not set
# BR2_PACKAGE_FBSET is not set
#
# other GUIs
#
#
# qt requires a toolchain with C++ support enabled
#
#
# X.org requires a toolchain with WCHAR support
#
#
# X libraries and helper libraries
#
# BR2_PACKAGE_ATK is not set
# BR2_PACKAGE_CAIRO is not set
# BR2_PACKAGE_PANGO is not set
# BR2_PACKAGE_LIBDRM is not set
# BR2_PACKAGE_LIBERATION is not set
# BR2_PACKAGE_LIBGLIB12 is not set
# BR2_PACKAGE_LIBGLIB2 is not set
# BR2_PACKAGE_OPENMOTIF is not set
# BR2_PACKAGE_FONTCONFIG is not set
# BR2_PACKAGE_FREETYPE is not set
# BR2_PACKAGE_TSLIB is not set
#
# webkit requires a toolchain with C++ support and WCHAR enabled
#
#
# X Window managers
#
# BR2_PACKAGE_MATCHBOX is not set
#
# X applications
#
# BR2_PACKAGE_ALSAMIXERGUI is not set
# BR2_PACKAGE_GQVIEW is not set
# BR2_PACKAGE_GOB2 is not set
# BR2_PACKAGE_LEAFPAD is not set
# BR2_PACKAGE_PCMANFM is not set
# BR2_PACKAGE_SYLPHEED is not set
# BR2_PACKAGE_TORSMO is not set
# BR2_PACKAGE_X11VNC is not set
# BR2_PACKAGE_XPDF is not set
# BR2_PACKAGE_XSTROKE is not set
#
# Compressors / decompressors
#
#
# libarchive requires a toolchain with WCHAR support
#
# BR2_PACKAGE_LZO is not set
# BR2_PACKAGE_LZOP is not set
#
# lzma requires a toolchain with C++ support
#
BR2_PACKAGE_ZLIB=y
#
# Package managers
#
# BR2_PACKAGE_IPKG is not set
# BR2_PACKAGE_PORTAGE is not set
#
# Interpreter languages / Scripting
#
# BR2_PACKAGE_LUA is not set
# BR2_PACKAGE_MICROPERL is not set
# BR2_PACKAGE_PYTHON is not set
#
# ruby requires a toolchain with WCHAR support
#
# BR2_PACKAGE_TCL is not set
# BR2_PACKAGE_PHP is not set
#
# XML handling
#
# BR2_PACKAGE_EXPAT is not set
# BR2_PACKAGE_EZXML is not set
# BR2_PACKAGE_LIBXML2 is not set
# BR2_PACKAGE_LIBXSLT is not set
#
# xerces-c++ requires a toolchain with C++ support enabled
#
#
# Java
#
# BR2_PACKAGE_CLASSPATH is not set
#
# Games
#
# BR2_PACKAGE_GNUCHESS is not set
# BR2_PACKAGE_MAGICCUBE4D is not set
# BR2_PACKAGE_PRBOOM is not set
# BR2_PACKAGE_RUBIX is not set
# BR2_PACKAGE_VICE is not set
# BR2_PACKAGE_XBOARD is not set
#
# Target filesystem options
#
BR2_ROOTFS_PREFIX="rootfs"
BR2_ROOTFS_SUFFIX=""
BR2_ROOTFS_POST_BUILD_SCRIPT=""
#
# filesystem for target device
#
# BR2_TARGET_ROOTFS_CRAMFS is not set
# BR2_TARGET_ROOTFS_CLOOP is not set
BR2_TARGET_ROOTFS_EXT2=y
BR2_TARGET_ROOTFS_EXT2_BLOCKS=0
BR2_TARGET_ROOTFS_EXT2_INODES=0
BR2_TARGET_ROOTFS_EXT2_RESBLKS=0
BR2_TARGET_ROOTFS_EXT2_SQUASH=y
BR2_TARGET_ROOTFS_EXT2_OUTPUT="$(IMAGE).ext2"
BR2_TARGET_ROOTFS_EXT2_NONE=y
# BR2_TARGET_ROOTFS_EXT2_GZIP is not set
# BR2_TARGET_ROOTFS_EXT2_BZIP2 is not set
# BR2_TARGET_ROOTFS_EXT2_LZMA is not set
BR2_TARGET_ROOTFS_EXT2_COPYTO=""
# BR2_TARGET_ROOTFS_JFFS2 is not set
# BR2_TARGET_ROOTFS_SQUASHFS is not set
BR2_TARGET_ROOTFS_TAR=y
BR2_TARGET_ROOTFS_TAR_NONE=y
# BR2_TARGET_ROOTFS_TAR_GZIP is not set
# BR2_TARGET_ROOTFS_TAR_BZIP2 is not set
# BR2_TARGET_ROOTFS_TAR_LZMA is not set
BR2_TARGET_ROOTFS_TAR_OPTIONS=""
BR2_TARGET_ROOTFS_TAR_COPYTO=""
# BR2_TARGET_ROOTFS_CPIO is not set
# BR2_TARGET_ROOTFS_INITRAMFS is not set
# BR2_TARGET_ROOTFS_ROMFS is not set
#
# bootloader for target device
#
BR2_TARGET_UBOOT=y
BR2_TARGET_UBOOT_BOARDNAME="$(BOARD_NAME)"
BR2_TARGET_UBOOT_2009_08=y
# BR2_TARGET_UBOOT_2009_06 is not set
# BR2_TARGET_UBOOT_2009_03 is not set
# BR2_TARGET_UBOOT_2009_01 is not set
# BR2_TARGET_UBOOT_2008_10 is not set
# BR2_TARGET_UBOOT_1_2_0_ATMEL is not set
BR2_UBOOT_VERSION="2009.08"
BR2_U_BOOT_SITE="ftp://ftp.denx.de/pub/u-boot"
# BR2_TARGET_U_BOOT_ARCH_PATCH is not set
BR2_TARGET_UBOOT_CUSTOM_PATCH=""
# BR2_TARGET_UBOOT_SILENT is not set
# BR2_TARGET_UBOOT_TOOL_MKIMAGE is not set
# BR2_TARGET_UBOOT_TOOL_ENV is not set
# BR2_TARGET_UBOOT_DEFAULT_ENV is not set
#
# Kernel
#
# BR2_KERNEL_none is not set
BR2_KERNEL_LINUX_ADVANCED=y
# BR2_KERNEL_LINUX is not set
BR2_PACKAGE_LINUX=y
BR2_PACKAGE_LINUX_KCONFIG="target/device/ARMLTD/$(BR2_BOARD_NAME)/$(BR2_BOARD_NAME)-linux26-$(BR2_LINUX26_VERSION).config"
BR2_PACKAGE_LINUX_FORMAT="uImage"
BR2_KERNEL_CURRENT_VERSION="2.6.30.2"
BR2_KERNEL_LATEST_2_6_30="2"
BR2_KERNEL_LATEST_2_6_29="6"
BR2_KERNEL_LATEST_2_6_28="10"
BR2_KERNEL_LATEST_2_6_27="27"
BR2_KERNEL_LATEST_2_6_26="8"
BR2_KERNEL_LATEST_2_6_25="19"
BR2_KERNEL_LATEST_2_6_24="7"
BR2_KERNEL_SITE="http://ftp.kernel.org/pub/linux/kernel/v2.6"
BR2_MM_PATCH_SITE="http://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6"
BR2_RC_MM_PATCH_DIR="$(BR2_KERNEL_NEXT_VERSION)-rc$(BR2_KERNEL_RC_LEVEL)/2.6.$(BR2_KERNEL_NEXT_VERSION)-rc$(BR2_KERNEL_RC_LEVEL)-mm$(BR2_KERNEL_MM_LEVEL)"
BR2_LINUX_2_6_STABLE=y
# BR2_LINUX_2_6_30 is not set
# BR2_LINUX_2_6_29 is not set
# BR2_LINUX_2_6_28 is not set
# BR2_LINUX_2_6_27 is not set
# BR2_LINUX_2_6_26 is not set
# BR2_LINUX_2_6_25 is not set
# BR2_LINUX_2_6_24 is not set
# BR2_LINUX_2_6_31 is not set
# BR2_LINUX26_CUSTOM is not set
#
# Patches
#
# BR2_KERNEL_ARCH_PATCH_ENABLED is not set
BR2_LINUX_BSP_PATCH=""
BR2_DOWNLOAD_LINUX26_VERSION="$(BR2_KERNEL_CURRENT_VERSION)"
BR2_LINUX26_VERSION="$(BR2_KERNEL_CURRENT_VERSION)"
#
# Linux Kernel Configuration
#
BR2_PACKAGE_LINUX_USE_KCONFIG=y
# BR2_PACKAGE_LINUX_USE_DEFCONFIG is not set
# BR2_PACKAGE_LINUX_USE_XCONFIG is not set
# BR2_LINUX_BIN_BZIMAGE is not set
BR2_LINUX_BIN_UIMAGE=y
# BR2_LINUX_BIN_VMLINUX is not set
# BR2_LINUX_BIN_ZIMAGE is not set
# BR2_LINUX_BIN_CUSTOM is not set
#
# Destinations for linux kernel binaries
#
# BR2_LINUX_COPYTO_ROOTFS is not set
# BR2_LINUX_COPYTO_TFTPBOOT is not set
BR2_LINUX_COPYTO=""
# BR2_LINUX_COPY_CONFIGURATION is not set
--
Grant Edwards grante Yow! I'm having fun
at HITCHHIKING to CINCINNATI
visi.com or FAR ROCKAWAY!!
^ permalink raw reply [flat|nested] 4+ messages in thread* [Buildroot] Buildroot How-To for QEMU/ARM
2010-01-27 16:10 ` Grant Edwards
@ 2010-01-30 16:58 ` Jim Thomas
2010-01-30 19:38 ` Grant Edwards
0 siblings, 1 reply; 4+ messages in thread
From: Jim Thomas @ 2010-01-30 16:58 UTC (permalink / raw)
To: buildroot
Hi Grant,
> Here's the .config file I last used -- AFAIR it was working at
> that point:
I tried your .config file and was still unsuccessful with QEMU.
I diffed your .config file against that produced by 'make integrator926_defconfig', and there were no signficant differences.
Perhaps I am not having a Buildroot issue, but a QEMU invocation issue.
Do you recall the qemu-system-arm invocation that worked for you with the Linux kernel and RFS created by buildroot-2009.11?
Thanks.
Jim
----- Original Message ----
From: Grant Edwards <grant.b.edwards@gmail.com>
To: buildroot at uclibc.org
Sent: Wed, January 27, 2010 10:10:35 AM
Subject: Re: [Buildroot] Buildroot How-To for QEMU/ARM
On 2010-01-27, Jim Thomas <jimthomasembedded@yahoo.com> wrote:
> Hello,
>
> I can build qemu-0.12.2 under Ubuntu 9.10 and boot Linux in
> QEMU using the pre-built kernel and RFS in arm-test-0.2, also
> from the QEMU project.
>
> Now I want to use QEMU to boot a Linux kernel and RFS that I
> built myself for ARM using buildroot-2009.11.
>
> I have not had much luck. Based on web searching, I have tried
> twisting knobs in 'make menuconfig' and rebuilt perhaps a
> couple of dozen times.
>
> Rather than do a core dump here of the details, I thought I
> would ask:
>
> Has anyone used buildroot-2009.11 to build a kernel and RFS
> for ARM that boot successfully under qemu-0.12.2?
I built for arm-integrator using HEAD back in
November/December, and it ran fine on qemu-0.9.1. I didn't do
much with it other than boot it up, log in, and test the
virtual serial ports.
> Do step-by-step notes exist for how to do this for ARM that
> were written for these latest versions of Buildroot and QEMU,
> or that have been verified as still complete and correct?
Not that I've found. There were some articles written a couple
years ago that have step-by-step instructions, but they're
missing a step or two and are also now out of date in a few
spots.
Here's the .config file I last used -- AFAIR it was working at
that point:
# Automatically generated make config: don't edit
# Wed Dec 16 09:10:07 2009
#
<snip>
--
Grant Edwards grante Yow! I'm having fun
at HITCHHIKING to CINCINNATI
visi.com or FAR ROCKAWAY!!
_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 4+ messages in thread* [Buildroot] Buildroot How-To for QEMU/ARM
2010-01-30 16:58 ` Jim Thomas
@ 2010-01-30 19:38 ` Grant Edwards
0 siblings, 0 replies; 4+ messages in thread
From: Grant Edwards @ 2010-01-30 19:38 UTC (permalink / raw)
To: buildroot
On 2010-01-30, Jim Thomas <jimthomasembedded@yahoo.com> wrote:
> Hi Grant,
>
> > Here's the .config file I last used -- AFAIR it was working at
> > that point:
>
> I tried your .config file and was still unsuccessful with QEMU.
>
> I diffed your .config file against that produced by 'make
> integrator926_defconfig', and there were no signficant
> differences.
>
> Perhaps I am not having a Buildroot issue, but a QEMU
> invocation issue.
>
> Do you recall the qemu-system-arm invocation that worked for
> you with the Linux kernel and RFS created by buildroot-2009.11?
I was using GIT HEAD and not buildroot-2009.11, but the
invokation was pretty much the same as shown on the web pages:
$ qemu-system-arm -kernel <filename> -initrd <filename>
I also played around with a couple Qemu options to enable more
serial ports that you connected to via telnet, and that all
worked the way it says it in the Qemu docs.
--
Grant Edwards grante Yow! I want to kill
at everyone here with a cute
visi.com colorful Hydrogen Bomb!!
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2010-01-30 19:38 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-01-27 15:28 [Buildroot] Buildroot How-To for QEMU/ARM Jim Thomas
2010-01-27 16:10 ` Grant Edwards
2010-01-30 16:58 ` Jim Thomas
2010-01-30 19:38 ` Grant Edwards
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox