From: Marek Vasut <marex@denx.de>
To: dri-devel@lists.freedesktop.org
Cc: Marek Vasut <marex@denx.de>, Robert Foss <robert.foss@linaro.org>,
Jagan Teki <jagan@amarulasolutions.com>,
Thomas Zimmermann <tzimmermann@suse.de>,
Sam Ravnborg <sam@ravnborg.org>,
Maxime Ripard <maxime@cerno.tech>
Subject: [PATCH V2 02/12] drm: bridge: icn6211: Fix HFP_HSW_HBP_HI and HFP_MIN handling
Date: Thu, 17 Feb 2022 01:25:20 +0100 [thread overview]
Message-ID: <20220217002530.396563-3-marex@denx.de> (raw)
In-Reply-To: <20220217002530.396563-1-marex@denx.de>
The HFP_HSW_HBP_HI register must be programmed with 2 LSbits of each
Horizontal Front Porch/Sync/Back Porch. Currently the driver programs
this register to 0, which breaks displays with either value above 255.
The HFP_MIN register must be set to the same value as HFP_LI, otherwise
there is visible image distortion, usually in the form of missing lines
at the bottom of the panel.
Fix this by correctly programming the HFP_HSW_HBP_HI and HFP_MIN registers.
Fixes: ce517f18944e3 ("drm: bridge: Add Chipone ICN6211 MIPI-DSI to RGB bridge")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
---
V2: Rebase on next-20220214
---
drivers/gpu/drm/bridge/chipone-icn6211.c | 23 ++++++++++++++++-------
1 file changed, 16 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/bridge/chipone-icn6211.c b/drivers/gpu/drm/bridge/chipone-icn6211.c
index 4b8d1a5a50302..e29e6a84c39a6 100644
--- a/drivers/gpu/drm/bridge/chipone-icn6211.c
+++ b/drivers/gpu/drm/bridge/chipone-icn6211.c
@@ -35,6 +35,9 @@
#define HSYNC_LI 0x24
#define HBP_LI 0x25
#define HFP_HSW_HBP_HI 0x26
+#define HFP_HSW_HBP_HI_HFP(n) (((n) & 0x300) >> 4)
+#define HFP_HSW_HBP_HI_HS(n) (((n) & 0x300) >> 6)
+#define HFP_HSW_HBP_HI_HBP(n) (((n) & 0x300) >> 8)
#define VFP 0x27
#define VSYNC 0x28
#define VBP 0x29
@@ -163,6 +166,7 @@ static void chipone_atomic_enable(struct drm_bridge *bridge,
{
struct chipone *icn = bridge_to_chipone(bridge);
struct drm_display_mode *mode = &icn->mode;
+ u16 hfp, hbp, hsync;
ICN6211_DSI(icn, MIPI_CFG_PW, MIPI_CFG_PW_CONFIG_DSI);
@@ -178,13 +182,18 @@ static void chipone_atomic_enable(struct drm_bridge *bridge,
((mode->hdisplay >> 8) & 0xf) |
(((mode->vdisplay >> 8) & 0xf) << 4));
- ICN6211_DSI(icn, HFP_LI, mode->hsync_start - mode->hdisplay);
+ hfp = mode->hsync_start - mode->hdisplay;
+ hsync = mode->hsync_end - mode->hsync_start;
+ hbp = mode->htotal - mode->hsync_end;
- ICN6211_DSI(icn, HSYNC_LI, mode->hsync_end - mode->hsync_start);
-
- ICN6211_DSI(icn, HBP_LI, mode->htotal - mode->hsync_end);
-
- ICN6211_DSI(icn, HFP_HSW_HBP_HI, 0x00);
+ ICN6211_DSI(icn, HFP_LI, hfp & 0xff);
+ ICN6211_DSI(icn, HSYNC_LI, hsync & 0xff);
+ ICN6211_DSI(icn, HBP_LI, hbp & 0xff);
+ /* Top two bits of Horizontal Front porch/Sync/Back porch */
+ ICN6211_DSI(icn, HFP_HSW_HBP_HI,
+ HFP_HSW_HBP_HI_HFP(hfp) |
+ HFP_HSW_HBP_HI_HS(hsync) |
+ HFP_HSW_HBP_HI_HBP(hbp));
ICN6211_DSI(icn, VFP, mode->vsync_start - mode->vdisplay);
@@ -194,7 +203,7 @@ static void chipone_atomic_enable(struct drm_bridge *bridge,
/* dsi specific sequence */
ICN6211_DSI(icn, SYNC_EVENT_DLY, 0x80);
- ICN6211_DSI(icn, HFP_MIN, 0x28);
+ ICN6211_DSI(icn, HFP_MIN, hfp & 0xff);
ICN6211_DSI(icn, MIPI_PD_CK_LANE, 0xa0);
ICN6211_DSI(icn, PLL_CTRL(12), 0xff);
ICN6211_DSI(icn, BIST_POL, BIST_POL_DE_POL);
--
2.34.1
next prev parent reply other threads:[~2022-02-17 0:26 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-02-17 0:25 [PATCH V2 00/12] drm: bridge: icn6211: Fix hard-coded panel settings and add I2C support Marek Vasut
2022-02-17 0:25 ` [PATCH V2 01/12] drm: bridge: icn6211: Fix register layout Marek Vasut
2022-03-02 9:55 ` Maxime Ripard
2022-02-17 0:25 ` Marek Vasut [this message]
2022-03-02 9:56 ` [PATCH V2 02/12] drm: bridge: icn6211: Fix HFP_HSW_HBP_HI and HFP_MIN handling Maxime Ripard
2022-02-17 0:25 ` [PATCH V2 03/12] drm: bridge: icn6211: Add HS/VS/DE polarity handling Marek Vasut
2022-03-02 9:59 ` Maxime Ripard
2022-03-02 14:45 ` Marek Vasut
2022-02-17 0:25 ` [PATCH V2 04/12] drm: bridge: icn6211: Add DSI lane count DT property parsing Marek Vasut
2022-03-02 10:01 ` Maxime Ripard
2022-03-02 15:17 ` Marek Vasut
2022-03-03 12:54 ` Maxime Ripard
2022-03-04 0:26 ` Marek Vasut
2022-02-17 0:25 ` [PATCH V2 05/12] drm: bridge: icn6211: Add generic DSI-to-DPI PLL configuration Marek Vasut
2022-03-02 10:02 ` Maxime Ripard
2022-02-17 0:25 ` [PATCH V2 06/12] drm: bridge: icn6211: Use DSI burst mode without EoT and with LP command mode Marek Vasut
2022-03-02 10:03 ` Maxime Ripard
2022-02-17 0:25 ` [PATCH V2 07/12] drm: bridge: icn6211: Disable DPI color swap Marek Vasut
2022-03-02 10:04 ` Maxime Ripard
2022-02-17 0:25 ` [PATCH V2 08/12] drm: bridge: icn6211: Set SYS_CTRL_1 to value used in examples Marek Vasut
2022-03-02 10:04 ` Maxime Ripard
2022-02-17 0:25 ` [PATCH V2 09/12] drm: bridge: icn6211: Implement atomic_get_input_bus_fmts Marek Vasut
2022-03-02 10:05 ` Maxime Ripard
2022-02-17 0:25 ` [PATCH V2 10/12] drm: bridge: icn6211: Add I2C configuration support Marek Vasut
2022-03-02 10:07 ` Maxime Ripard
2022-02-17 0:25 ` [PATCH V2 11/12] drm: bridge: icn6211: Rework ICN6211_DSI to chipone_writeb() Marek Vasut
2022-03-02 10:08 ` Maxime Ripard
2022-02-17 0:25 ` [PATCH V2 12/12] drm: bridge: icn6211: Read and validate chip IDs before configuration Marek Vasut
2022-03-02 10:08 ` Maxime Ripard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220217002530.396563-3-marex@denx.de \
--to=marex@denx.de \
--cc=dri-devel@lists.freedesktop.org \
--cc=jagan@amarulasolutions.com \
--cc=maxime@cerno.tech \
--cc=robert.foss@linaro.org \
--cc=sam@ravnborg.org \
--cc=tzimmermann@suse.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox