dri-devel.lists.freedesktop.org archive mirror
 help / color / mirror / Atom feed
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: Adam Ford <aford173@gmail.com>
Cc: "Neil Armstrong" <neil.armstrong@linaro.org>,
	"Robert Foss" <rfoss@kernel.org>,
	"Andrzej Hajda" <andrzej.hajda@intel.com>,
	"Geert Uytterhoeven" <geert+renesas@glider.be>,
	"Jonas Karlman" <jonas@kwiboo.se>,
	dri-devel@lists.freedesktop.org,
	"Abhinav Kumar" <quic_abhinavk@quicinc.com>,
	"Jernej Skrabec" <jernej.skrabec@gmail.com>,
	"Javier Martinez Canillas" <javierm@redhat.com>,
	linux-renesas-soc@vger.kernel.org,
	"Andy Shevchenko" <andy.shevchenko@gmail.com>,
	"Bogdan Togorean" <bogdan.togorean@analog.com>,
	"Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>,
	"Biju Das" <biju.das.jz@bp.renesas.com>,
	"Ahmad Fatoum" <a.fatoum@pengutronix.de>
Subject: Re: [PATCH 7/7] drm: adv7511: Add hpd_override_enable feature bit to struct adv7511_chip_info
Date: Tue, 29 Aug 2023 10:36:56 +0300	[thread overview]
Message-ID: <20230829073656.GC2302@pendragon.ideasonboard.com> (raw)
In-Reply-To: <CAHCN7xKo4Gnt+3rBgNyHq5tAAWU+nUpfJjzgb4RSPrgOgRsuyw@mail.gmail.com>

On Fri, Aug 18, 2023 at 07:41:45AM -0500, Adam Ford wrote:
> On Sun, Aug 13, 2023 at 1:06 PM Biju Das <biju.das.jz@bp.renesas.com> wrote:
> >
> > As per spec, it is allowed to pulse the HPD signal to indicate that the
> > EDID information has changed. Some monitors do this when they wake up
> > from standby or are enabled. When the HPD goes low the adv7511 is
> > reset and the outputs are disabled which might cause the monitor to
> > go to standby again. To avoid this we ignore the HPD pin for the
> > first few seconds after enabling the output. On the other hand,
> > adv7535 require to enable HPD Override bit for proper HPD.
> >
> > Add hpd_override_enable feature bit to struct adv7511_chip_info to handle
> > this scenario.
> >
> > While at it, drop the enum adv7511_type as it is unused.
> 
> It seems like dropping adv7511_type is unrelated to the rest of the
> patch, and I think it should be split from this into its own patch

Dropping the enum with its last user makes sense, but I think the series
may go a bit too far by adding to the info structure bits that don't
really describe logical features, but are half made up for the sole
purpose of dropping the enum. I would prefer keeping the enum for the
handful of places where a type check makes more sense (in my opinion).

> > Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
> > ---
> >  drivers/gpu/drm/bridge/adv7511/adv7511.h     |  8 +-------
> >  drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 12 +++++-------
> >  2 files changed, 6 insertions(+), 14 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511.h b/drivers/gpu/drm/bridge/adv7511/adv7511.h
> > index 627531f48f84..c523ac4c9bc8 100644
> > --- a/drivers/gpu/drm/bridge/adv7511/adv7511.h
> > +++ b/drivers/gpu/drm/bridge/adv7511/adv7511.h
> > @@ -325,22 +325,16 @@ struct adv7511_video_config {
> >         struct hdmi_avi_infoframe avi_infoframe;
> >  };
> >
> > -enum adv7511_type {
> > -       ADV7511,
> > -       ADV7533,
> > -       ADV7535,
> > -};
> > -
> >  #define ADV7511_MAX_ADDRS 3
> >
> >  struct adv7511_chip_info {
> > -       enum adv7511_type type;
> >         unsigned long max_mode_clock;
> >         unsigned long max_lane_freq;
> >         const char * const *supply_names;
> >         unsigned int num_supplies;
> >         unsigned has_dsi:1;
> >         unsigned link_config:1;
> > +       unsigned hpd_override_enable:1;
> >  };
> >
> >  struct adv7511 {
> > diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> > index 6974c267b1d5..7b06a0a21685 100644
> > --- a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> > +++ b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> > @@ -354,7 +354,7 @@ static void __adv7511_power_on(struct adv7511 *adv7511)
> >          * first few seconds after enabling the output. On the other hand
> >          * adv7535 require to enable HPD Override bit for proper HPD.
> >          */
> > -       if (adv7511->info->type == ADV7535)
> > +       if (adv7511->info->hpd_override_enable)
> >                 regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
> >                                    ADV7535_REG_POWER2_HPD_OVERRIDE,
> >                                    ADV7535_REG_POWER2_HPD_OVERRIDE);
> > @@ -381,7 +381,7 @@ static void adv7511_power_on(struct adv7511 *adv7511)
> >  static void __adv7511_power_off(struct adv7511 *adv7511)
> >  {
> >         /* TODO: setup additional power down modes */
> > -       if (adv7511->info->type == ADV7535)
> > +       if (adv7511->info->hpd_override_enable)
> >                 regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
> >                                    ADV7535_REG_POWER2_HPD_OVERRIDE, 0);
> >
> > @@ -682,7 +682,7 @@ adv7511_detect(struct adv7511 *adv7511, struct drm_connector *connector)
> >                         status = connector_status_disconnected;
> >         } else {
> >                 /* Renable HPD sensing */
> > -               if (adv7511->info->type == ADV7535)
> > +               if (adv7511->info->hpd_override_enable)
> >                         regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
> >                                            ADV7535_REG_POWER2_HPD_OVERRIDE,
> >                                            ADV7535_REG_POWER2_HPD_OVERRIDE);
> > @@ -1360,14 +1360,12 @@ static void adv7511_remove(struct i2c_client *i2c)
> >  }
> >
> >  static const struct adv7511_chip_info adv7511_chip_info = {
> > -       .type = ADV7511,
> >         .supply_names = adv7511_supply_names,
> >         .num_supplies = ARRAY_SIZE(adv7511_supply_names),
> >         .link_config = 1
> >  };
> >
> >  static const struct adv7511_chip_info adv7533_chip_info = {
> > -       .type = ADV7533,
> >         .max_mode_clock = 80000,
> >         .max_lane_freq = 800000,
> >         .supply_names = adv7533_supply_names,
> > @@ -1376,12 +1374,12 @@ static const struct adv7511_chip_info adv7533_chip_info = {
> >  };
> >
> >  static const struct adv7511_chip_info adv7535_chip_info = {
> > -       .type = ADV7535,
> >         .max_mode_clock = 148500,
> >         .max_lane_freq = 891000,
> >         .supply_names = adv7533_supply_names,
> >         .num_supplies = ARRAY_SIZE(adv7533_supply_names),
> > -       .has_dsi = 1
> > +       .has_dsi = 1,
> > +       .hpd_override_enable = 1
> >  };
> >
> >  static const struct i2c_device_id adv7511_i2c_ids[] = {

-- 
Regards,

Laurent Pinchart

  parent reply	other threads:[~2023-08-29  7:36 UTC|newest]

Thread overview: 32+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-08-13 18:05 [PATCH 0/7] ADV7511 driver enhancements Biju Das
2023-08-13 18:05 ` [PATCH 1/7] drm: adv7511: Add struct adv7511_chip_info and use i2c_get_match_data() Biju Das
2023-08-18 14:49   ` Adam Ford
2023-08-29  7:22   ` Laurent Pinchart
2023-08-29 14:00     ` Biju Das
2023-08-13 18:05 ` [PATCH 2/7] drm: adv7511: Add max_mode_clock variable to struct adv7511_chip_info Biju Das
2023-08-28 22:36   ` Adam Ford
2023-08-29  7:23   ` Laurent Pinchart
2023-08-29 14:01     ` Biju Das
2023-08-13 18:05 ` [PATCH 3/7] drm: adv7511: Add max_lane_freq " Biju Das
2023-08-29  7:25   ` Laurent Pinchart
2023-08-29 14:05     ` Biju Das
2023-08-13 18:05 ` [PATCH 4/7] drm: adv7511: Add supply_names and num_supplies variables " Biju Das
2023-08-29  7:26   ` Laurent Pinchart
2023-08-29 14:06     ` Biju Das
2023-08-13 18:05 ` [PATCH 5/7] drm: adv7511: Add has_dsi feature bit " Biju Das
2023-08-29  7:30   ` Laurent Pinchart
2023-08-29 14:19     ` Biju Das
2023-08-29 15:35       ` Laurent Pinchart
2023-08-29 15:42         ` Biju Das
2023-08-30  8:22           ` Laurent Pinchart
2023-08-13 18:05 ` [PATCH 6/7] drm: adv7511: Add link_config " Biju Das
2023-08-29  7:34   ` Laurent Pinchart
2023-08-29 14:20     ` Biju Das
2023-08-13 18:05 ` [PATCH 7/7] drm: adv7511: Add hpd_override_enable " Biju Das
2023-08-18 12:41   ` Adam Ford
2023-08-18 13:34     ` Biju Das
2023-08-18 13:37       ` Adam Ford
2023-08-18 13:44         ` Biju Das
2023-08-29  7:36     ` Laurent Pinchart [this message]
2023-08-29 14:22       ` Biju Das
2023-08-18 13:56 ` [PATCH 0/7] ADV7511 driver enhancements Fabio Estevam

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230829073656.GC2302@pendragon.ideasonboard.com \
    --to=laurent.pinchart@ideasonboard.com \
    --cc=a.fatoum@pengutronix.de \
    --cc=aford173@gmail.com \
    --cc=andrzej.hajda@intel.com \
    --cc=andy.shevchenko@gmail.com \
    --cc=biju.das.jz@bp.renesas.com \
    --cc=bogdan.togorean@analog.com \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=geert+renesas@glider.be \
    --cc=javierm@redhat.com \
    --cc=jernej.skrabec@gmail.com \
    --cc=jonas@kwiboo.se \
    --cc=linux-renesas-soc@vger.kernel.org \
    --cc=neil.armstrong@linaro.org \
    --cc=quic_abhinavk@quicinc.com \
    --cc=rfoss@kernel.org \
    --cc=u.kleine-koenig@pengutronix.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).