Re: [PATCH 00/17] drm/mgag200: Convert to atomic modesetting

[John Donnelly <John.P.Donnelly@Oracle.com>]

On 4/30/20 3:29 AM, Thomas Zimmermann wrote:
> Hi John
> 
> Am 30.04.20 um 02:11 schrieb John Donnelly:
>> On 4/29/20 9:32 AM, Thomas Zimmermann wrote:
>>> This patchset converts mgag200 to atomic modesetting. It uses simple
>>> KMS helpers and SHMEM.
>>>
>>> Patches 1 to 4 simplifies the driver before the conversion. For example,
>>> the HW cursor is not usable with the way universal planes work. A few
>>> data structures can be cleaned up.
>>>
>>> Patches 5 to 15 untangle the existing modesetting code into smaller
>>> functions. Specifically, mode setting and plane updates are being
>>> separated from each other.
>>>
>>> Patch 16 converts mgag200 to simple KMS helpers and enables atomic
>>> mode setting.
>>>
>>> As some HW seems to require a framebuffer offset of 0 within the video
>>> memory, it does not work with atomic modesetting. Atomically switching
>>> plane framebuffers, requires either source or target buffer to be located
>>> at a non-0 offet. To resolve this problem, patch 17 converts mgag200 from
>>> VRAM helpers to SHMEM helpers. During plane updates, the content of the
>>> SHMEM BO is memcpy'd to VRAM. From my subjective obersation, performance
>>> is not nuch different from the original code.
>>>
>>> The patchset has been tested on MGA G200EH hardware.
>>>
>>> Thomas Zimmermann (17):
>>>     drm/mgag200: Remove HW cursor
>>>     drm/mgag200: Remove unused fields from struct mga_device
>>>     drm/mgag200: Embed connector instance in struct mga_device
>>>     drm/mgag200: Use managed mode-config initialization
>>>     drm/mgag200: Clean up mga_set_start_address()
>>>     drm/mgag200: Clean up mga_crtc_do_set_base()
>>>     drm/mgag200: Move mode-setting code into separate helper function
>>>     drm/mgag200: Split MISC register update into PLL selection, SYNC and
>>>       I/O
>>>     drm/mgag200: Update mode registers after plane registers
>>>     drm/mgag200: Set pitch in a separate helper function
>>>     drm/mgag200: Set primary plane's format in separate helper function
>>>     drm/mgag200: Move TAGFIFO reset into separate function
>>>     drm/mgag200: Move hiprilvl setting into separate functions
>>>     drm/mgag200: Move register initialization into separate function
>>>     drm/mgag200: Remove waiting from DPMS code
>>>     drm/mgag200: Convert to simple KMS helper
>>>     drm/mgag200: Replace VRAM helpers with SHMEM helpers
>>>
>>>    drivers/gpu/drm/mgag200/Kconfig          |   4 +-
>>>    drivers/gpu/drm/mgag200/Makefile         |   2 +-
>>>    drivers/gpu/drm/mgag200/mgag200_cursor.c | 319 --------
>>>    drivers/gpu/drm/mgag200/mgag200_drv.c    |  51 +-
>>>    drivers/gpu/drm/mgag200/mgag200_drv.h    |  43 +-
>>>    drivers/gpu/drm/mgag200/mgag200_main.c   |  28 -
>>>    drivers/gpu/drm/mgag200/mgag200_mode.c   | 948 ++++++++++++-----------
>>>    drivers/gpu/drm/mgag200/mgag200_reg.h    |   5 +-
>>>    drivers/gpu/drm/mgag200/mgag200_ttm.c    |  35 +-
>>>    9 files changed, 563 insertions(+), 872 deletions(-)
>>>    delete mode 100644 drivers/gpu/drm/mgag200/mgag200_cursor.c
>>>
>>> -- 
>>> 2.26.0
>>>
>>
>>
>>   Hi Thomas ,
>>
>>   I would like to test this on hardware that uses this device integrated
>> into as BMC  ( iLo ) that I have ran into problems before. Can you post
>> your staging URL so I can clone it ?
> 
> Sure, I'll set something up for you. But it could take until next week.
> I promise not to merge the patches before you had a chance to test them.
> 
> Best regards
> Thomas
> 
  Hi

    I may try to apply these patches locally .. It won't be until next 
week though .


>>
>>
>> ( Thank you for CC'ing me. I removed my email from on dlist recently) .
>>
>>
>>
>>
> 


-- 
Thank You,
John
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel