dri-devel Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: sashiko-bot@kernel.org
To: "Yongxing Mou" <yongxing.mou@oss.qualcomm.com>
Cc: dri-devel@lists.freedesktop.org
Subject: Re: [PATCH v9 15/29] drm/msm/dpu: use stream_id to select MST interfaces
Date: Thu, 19 Nov 2026 08:35:34 +0000	[thread overview]
Message-ID: <sashiko-outbox-222682@kernel.org> (raw)
In-Reply-To: <20261119-msm-dp-mst-v9-15-ca61be4edfc3@oss.qualcomm.com>

Thank you for your contribution! Sashiko AI review found 1 potential
issue to consider:
- [Low] drm/msm/dpu: missing colon on @stream_id kernel-doc tag in
  msm_display_info
--

commit 1ac8db8a30bd58946d55f189ddce5112daaa02b5
Author: Yongxing Mou <yongxing.mou@oss.qualcomm.com>

drm/msm/dpu: use stream_id to select MST interfaces

This commit adds a stream_id field to struct msm_display_info and uses it in
dpu_encoder_get_intf() to select the matching DPU interface for MST streams.

[Severity: Low]
In drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.h (lines 31 and 39), the new
@stream_id kernel-doc tag on struct msm_display_info is missing a trailing
colon (@stream_id:). Without the colon, scripts/kernel-doc folds the line
into the preceding section and warns that struct member stream_id is not
described in msm_display_info.

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20261119-msm-dp-mst-v9-0-ca61be4edfc3@oss.qualcomm.com?part=15

  reply	other threads:[~2026-11-19  8:35 UTC|newest]

Thread overview: 46+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-11-19  8:24 [PATCH v9 00/29] drm/msm/dp: Add MST support for MSM chipsets Yongxing Mou
2026-11-19  8:24 ` [PATCH v9 01/29] drm/msm/dp: skip sink requests while the mainlink clocks are off Yongxing Mou
2026-11-19  8:24 ` [PATCH v9 02/29] drm/msm/dp: add support to send ACT packets for MST Yongxing Mou
2026-11-19  8:24 ` [PATCH v9 03/29] drm/msm/dp: add support to enable MST in mainlink control Yongxing Mou
2026-11-19  8:24 ` [PATCH v9 04/29] drm/msm/dp: no need to update tu calculation for mst Yongxing Mou
2026-11-19  8:24 ` [PATCH v9 05/29] drm/msm/dp: always program MST_FIFO_CONSTANT_FILL for MST use cases Yongxing Mou
2026-11-19  8:24 ` [PATCH v9 06/29] drm/msm/dp: add support for sending VCPF packets in DP controller Yongxing Mou
2026-11-19  8:24 ` [PATCH v9 07/29] drm/msm/dp: add support for MST channel slot allocation Yongxing Mou
2026-11-19  8:24 ` [PATCH v9 08/29] drm/msm/dp: replace power_on with active_stream_mask Yongxing Mou
2026-11-19  8:24 ` [PATCH v9 09/29] drm/msm/dp: factor out _helper variants of bridge ops accepting a panel Yongxing Mou
2026-11-19  8:24 ` [PATCH v9 10/29] drm/msm/dp: add link_ready to manage link-level operations Yongxing Mou
2026-11-19  8:24 ` [PATCH v9 11/29] drm/msm/dp: add msm_dp_display_get_panel() to initialize DP panel Yongxing Mou
2026-11-19  8:36   ` sashiko-bot
2026-11-19  8:24 ` [PATCH v9 12/29] drm/msm/dp: introduce dp_mst_drm module Yongxing Mou
2026-11-19  8:24 ` [PATCH v9 13/29] drm/msm/dp: add MST connector creation and topology callbacks Yongxing Mou
2026-11-19  8:49   ` sashiko-bot
2026-11-19  8:24 ` [PATCH v9 14/29] drm/msm/dpu: pass msm_display_info to dpu_encoder_get_intf() Yongxing Mou
2026-11-19  8:24 ` [PATCH v9 15/29] drm/msm/dpu: use stream_id to select MST interfaces Yongxing Mou
2026-11-19  8:35   ` sashiko-bot [this message]
2026-11-19  8:24 ` [PATCH v9 16/29] drm/msm/dpu: add per-stream MST encoders Yongxing Mou
2026-11-19  8:51   ` sashiko-bot
2026-11-19  8:24 ` [PATCH v9 17/29] drm/msm/dp: move link capabilities to dp_link Yongxing Mou
2026-11-19  8:41   ` sashiko-bot
2026-11-19  8:24 ` [PATCH v9 18/29] drm/msm/dp: add atomic stream handling for MST Yongxing Mou
2026-11-19  9:01   ` sashiko-bot
2026-11-19  8:24 ` [PATCH v9 19/29] drm/bridge_connector: suppress hotplug for IRQ_HPD without status changes Yongxing Mou
2026-11-19  9:01   ` sashiko-bot
2026-11-19  8:24 ` [PATCH v9 20/29] drm/bridge_connector: avoid detect-based HPD notifications for DisplayPort Yongxing Mou
2026-11-19  8:45   ` sashiko-bot
2026-11-19  8:24 ` [PATCH v9 21/29] drm/msm/dp: add HPD callback for dp MST Yongxing Mou
2026-11-19  8:50   ` sashiko-bot
2026-11-19  8:24 ` [PATCH v9 22/29] drm/msm/dp: wire MST helpers into atomic check and commit paths Yongxing Mou
2026-11-19  8:46   ` sashiko-bot
2026-11-19  8:24 ` [PATCH v9 23/29] drm/msm/dp: mark the SST bridge disconnected when mst is active Yongxing Mou
2026-11-19  8:46   ` sashiko-bot
2026-11-19  8:24 ` [PATCH v9 24/29] drm/msm/dp: enable MST on capable sinks Yongxing Mou
2026-11-19  9:05   ` sashiko-bot
2026-11-19  8:24 ` [PATCH v9 25/29] drm/msm/dp: mark the SST bridge disconnected when an MST-capable sink is present Yongxing Mou
2026-11-19  8:51   ` sashiko-bot
2026-11-19  8:24 ` [PATCH v9 26/29] drm/msm/dp: wake threaded handler for HPD IRQs Yongxing Mou
2026-11-19  8:49   ` sashiko-bot
2026-11-19  8:24 ` [PATCH v9 27/29] drm/msm/dp: ignore IRQ HPD latched together with an unplug Yongxing Mou
2026-11-19  8:24 ` [PATCH v9 28/29] drm/msm/dp: select MST stream bpp during atomic check Yongxing Mou
2026-11-19  8:50   ` sashiko-bot
2026-11-19  8:24 ` [PATCH v9 29/29] soc: qcom: pmic-glink-altmode: skip retimer reset on DP IRQ Yongxing Mou
2026-11-19 11:54 ` [PATCH v9 00/29] drm/msm/dp: Add MST support for MSM chipsets Joonhoe Kim

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=sashiko-outbox-222682@kernel.org \
    --to=sashiko-bot@kernel.org \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=sashiko-reviews@lists.linux.dev \
    --cc=yongxing.mou@oss.qualcomm.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox