Intel-GFX Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
To: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Intel Graphics Development <intel-gfx@lists.freedesktop.org>
Subject: Re: [PATCH 13/15] drm/i915: move fdi lane configuration checks ahead
Date: Mon, 22 Apr 2013 13:32:37 +0300	[thread overview]
Message-ID: <20130422103237.GY4469@intel.com> (raw)
In-Reply-To: <1366363487-15926-14-git-send-email-daniel.vetter@ffwll.ch>

On Fri, Apr 19, 2013 at 11:24:45AM +0200, Daniel Vetter wrote:
> This nicely allows us to drop some hacks which have only been used
> to work around modeset failures due to lack of fdi lanes.
> 
> v2: Implement proper checking for Haswell platforms - the fdi link to
> the LPT PCH has only 2 lanes. Note that we already filter out
> impossible modes in intel_crt_mode_valid. Unfortunately LPT does not
> support 6bpc on the fdi rx, so we can't pull clever tricks to squeeze
> in a few more modes.
> 
> v2: Rebased on top of Ben Widawsky's num_pipes reorg.
> 
> v3: Rebase on top of Ville's pipe debug output ocd rampage.
> 
> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
> ---
>  drivers/gpu/drm/i915/intel_display.c | 129 ++++++++++++++++++-----------------
>  1 file changed, 65 insertions(+), 64 deletions(-)
> 
> diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
> index c9a2f0b..6bcb196 100644
> --- a/drivers/gpu/drm/i915/intel_display.c
> +++ b/drivers/gpu/drm/i915/intel_display.c
> @@ -3955,9 +3955,68 @@ bool intel_connector_get_hw_state(struct intel_connector *connector)
>  	return encoder->get_hw_state(encoder, &pipe);
>  }
>  
> -static void ironlake_fdi_compute_config(struct drm_device *dev,
> +static bool ironlake_check_fdi_lanes(struct drm_device *dev, enum pipe pipe,
> +				     struct intel_crtc_config *pipe_config)
> +{
> +	struct drm_i915_private *dev_priv = dev->dev_private;
> +	struct intel_crtc *pipe_B_crtc =
> +		to_intel_crtc(dev_priv->pipe_to_crtc_mapping[PIPE_B]);
> +
> +	DRM_DEBUG_KMS("checking fdi config on pipe %i, lanes %i\n",
                                                   ^^

%c

More of the same below.

> +		      pipe_name(pipe), pipe_config->fdi_lanes);
> +	if (pipe_config->fdi_lanes > 4) {
> +		DRM_DEBUG_KMS("invalid fdi lane config on pipe %i: %i lanes\n",
> +			      pipe_name(pipe), pipe_config->fdi_lanes);
> +		return false;
> +	}
> +
> +	if (IS_HASWELL(dev)) {
> +		if (pipe_config->fdi_lanes > 2) {
> +			DRM_DEBUG_KMS("only 2 lanes on haswell, required: %i lanes\n",
> +				      pipe_config->fdi_lanes);
> +			return false;
> +		} else {
> +			return true;
> +		}
> +	}
> +
> +	if (INTEL_INFO(dev)->num_pipes)
> +		return true;
> +
> +	/* Ivybridge 3 pipe is really complicated */
> +	switch (pipe) {
> +	case PIPE_A:
> +		return true;
> +	case PIPE_B:
> +		if (dev_priv->pipe_to_crtc_mapping[PIPE_C]->enabled &&
> +		    pipe_config->fdi_lanes > 2) {
> +			DRM_DEBUG_KMS("invalid shared fdi lane config on pipe %i: %i lanes\n",
> +				      pipe_name(pipe), pipe_config->fdi_lanes);
> +			return false;
> +		}
> +		return true;
> +	case PIPE_C:
> +		if (!pipe_B_crtc->base.enabled ||
> +		    pipe_B_crtc->config.fdi_lanes <= 2) {
> +			if (pipe_config->fdi_lanes > 2) {
> +				DRM_DEBUG_KMS("invalid shared fdi lane config on pipe %i: %i lanes\n",
> +					      pipe_name(pipe), pipe_config->fdi_lanes);
> +				return false;
> +			}
> +		} else {
> +			DRM_DEBUG_KMS("fdi link B uses too many lanes to enable link C\n");
> +			return false;
> +		}
> +		return true;
> +	default:
> +		BUG();
> +	}
> +}
> +
> +static bool ironlake_fdi_compute_config(struct intel_crtc *intel_crtc,
>  					struct intel_crtc_config *pipe_config)
>  {
> +	struct drm_device *dev = intel_crtc->base.dev;
>  	struct drm_display_mode *adjusted_mode = &pipe_config->adjusted_mode;
>  	int target_clock, lane, link_bw;
>  
> @@ -3984,6 +4043,9 @@ static void ironlake_fdi_compute_config(struct drm_device *dev,
>  		link_bw *= pipe_config->pixel_multiplier;
>  	intel_link_compute_m_n(pipe_config->pipe_bpp, lane, target_clock,
>  			       link_bw, &pipe_config->fdi_m_n);
> +
> +	return ironlake_check_fdi_lanes(intel_crtc->base.dev,
> +					intel_crtc->pipe, pipe_config);
>  }
>  
>  static bool intel_crtc_compute_config(struct drm_crtc *crtc,
> @@ -4021,7 +4083,7 @@ static bool intel_crtc_compute_config(struct drm_crtc *crtc,
>  	}
>  
>  	if (pipe_config->has_pch_encoder)
> -		ironlake_fdi_compute_config(dev, pipe_config);
> +		return ironlake_fdi_compute_config(to_intel_crtc(crtc), pipe_config);
>  
>  	return true;
>  }
> @@ -5405,63 +5467,6 @@ static void cpt_enable_fdi_bc_bifurcation(struct drm_device *dev)
>  	POSTING_READ(SOUTH_CHICKEN1);
>  }
>  
> -static bool ironlake_check_fdi_lanes(struct intel_crtc *intel_crtc)
> -{
> -	struct drm_device *dev = intel_crtc->base.dev;
> -	struct drm_i915_private *dev_priv = dev->dev_private;
> -	struct intel_crtc *pipe_B_crtc =
> -		to_intel_crtc(dev_priv->pipe_to_crtc_mapping[PIPE_B]);
> -
> -	DRM_DEBUG_KMS("checking fdi config on pipe %c, lanes %i\n",
> -		      pipe_name(intel_crtc->pipe), intel_crtc->config.fdi_lanes);
> -	if (intel_crtc->config.fdi_lanes > 4) {
> -		DRM_DEBUG_KMS("invalid fdi lane config on pipe %c: %i lanes\n",
> -			      pipe_name(intel_crtc->pipe), intel_crtc->config.fdi_lanes);
> -		/* Clamp lanes to avoid programming the hw with bogus values. */
> -		intel_crtc->config.fdi_lanes = 4;
> -
> -		return false;
> -	}
> -
> -	if (INTEL_INFO(dev)->num_pipes == 2)
> -		return true;
> -
> -	switch (intel_crtc->pipe) {
> -	case PIPE_A:
> -		return true;
> -	case PIPE_B:
> -		if (dev_priv->pipe_to_crtc_mapping[PIPE_C]->enabled &&
> -		    intel_crtc->config.fdi_lanes > 2) {
> -			DRM_DEBUG_KMS("invalid shared fdi lane config on pipe %c: %i lanes\n",
> -				      pipe_name(intel_crtc->pipe), intel_crtc->config.fdi_lanes);
> -			/* Clamp lanes to avoid programming the hw with bogus values. */
> -			intel_crtc->config.fdi_lanes = 2;
> -
> -			return false;
> -		}
> -
> -		return true;
> -	case PIPE_C:
> -		if (!pipe_B_crtc->base.enabled || pipe_B_crtc->config.fdi_lanes <= 2) {
> -			if (intel_crtc->config.fdi_lanes > 2) {
> -				DRM_DEBUG_KMS("invalid shared fdi lane config on pipe %c: %i lanes\n",
> -					      pipe_name(intel_crtc->pipe), intel_crtc->config.fdi_lanes);
> -				/* Clamp lanes to avoid programming the hw with bogus values. */
> -				intel_crtc->config.fdi_lanes = 2;
> -
> -				return false;
> -			}
> -		} else {
> -			DRM_DEBUG_KMS("fdi link B uses too many lanes to enable link C\n");
> -			return false;
> -		}
> -
> -		return true;
> -	default:
> -		BUG();
> -	}
> -}
> -
>  static void ivybridge_update_fdi_bc_bifurcation(struct intel_crtc *intel_crtc)
>  {
>  	struct drm_device *dev = intel_crtc->base.dev;
> @@ -5653,7 +5658,6 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
>  	bool is_lvds = false;
>  	struct intel_encoder *encoder;
>  	int ret;
> -	bool fdi_config_ok;
>  
>  	for_each_encoder_on_crtc(dev, crtc, encoder) {
>  		switch (encoder->type) {
> @@ -5747,14 +5751,11 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
>  
>  	intel_set_pipe_timings(intel_crtc, mode, adjusted_mode);
>  
> -	/* Note, this also computes intel_crtc->fdi_lanes which is used below in
> -	 * ironlake_check_fdi_lanes. */
>  	if (intel_crtc->config.has_pch_encoder) {
>  		intel_cpu_transcoder_set_m_n(intel_crtc,
>  					     &intel_crtc->config.fdi_m_n);
>  	}
>  
> -	fdi_config_ok = ironlake_check_fdi_lanes(intel_crtc);
>  	if (IS_IVYBRIDGE(dev))
>  		ivybridge_update_fdi_bc_bifurcation(intel_crtc);
>  
> @@ -5770,7 +5771,7 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
>  
>  	intel_update_linetime_watermarks(dev, pipe, adjusted_mode);
>  
> -	return fdi_config_ok ? ret : -EINVAL;
> +	return ret;
>  }
>  
>  static bool ironlake_get_pipe_config(struct intel_crtc *crtc,
> -- 
> 1.7.11.7
> 
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx@lists.freedesktop.org
> http://lists.freedesktop.org/mailman/listinfo/intel-gfx

-- 
Ville Syrjälä
Intel OTC

  reply	other threads:[~2013-04-22 10:32 UTC|newest]

Thread overview: 59+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2013-04-19  9:24 [PATCH 00/15] high-bpp fixes and fdi auto dithering Daniel Vetter
2013-04-19  9:24 ` [PATCH 01/15] drm/i915: fixup 12bpc hdmi dotclock handling Daniel Vetter
2013-04-23 15:02   ` Ville Syrjälä
2013-04-23 15:37     ` Daniel Vetter
2013-04-19  9:24 ` [PATCH 02/15] drm/i915: Disable high-bpc on pre-1.4 EDID screens Daniel Vetter
2013-04-23 15:07   ` Ville Syrjälä
2013-04-24 10:54     ` Daniel Vetter
2013-04-19  9:24 ` [PATCH 03/15] drm/i915: force bpp for eDP panels Daniel Vetter
2013-04-19 20:31   ` [PATCH] " Daniel Vetter
2013-04-19  9:24 ` [PATCH 04/15] drm/i915: drop adjusted_mode from *_set_pipeconf functions Daniel Vetter
2013-04-23 15:12   ` Ville Syrjälä
2013-04-19  9:24 ` [PATCH 05/15] drm/i915: implement high-bpc + pipeconf-dither support for g4x/vlv Daniel Vetter
2013-04-19 16:39   ` Jesse Barnes
2013-04-19 18:17     ` [PATCH] " Daniel Vetter
2013-04-19 18:39       ` Jesse Barnes
2013-04-19 19:29         ` Daniel Vetter
2013-04-23 15:27       ` Ville Syrjälä
2013-04-23 20:39         ` Daniel Vetter
2013-04-23 22:27           ` Daniel Vetter
2013-04-24 11:07             ` Ville Syrjälä
2013-04-23 22:30         ` Daniel Vetter
2013-04-24 11:11           ` Ville Syrjälä
2013-04-24 12:57             ` Daniel Vetter
2013-04-24 13:07               ` Ville Syrjälä
2013-04-19  9:24 ` [PATCH 06/15] drm/i915: allow high-bpc modes on DP Daniel Vetter
2013-04-29 10:16   ` Imre Deak
2013-04-19  9:24 ` [PATCH 07/15] drm/i915: Fixup non-24bpp support for VGA screens on Haswell Daniel Vetter
2013-04-24 11:12   ` Ville Syrjälä
2013-04-24 12:50     ` Daniel Vetter
2013-04-19  9:24 ` [PATCH 08/15] drm/i915: move intel_crtc->fdi_lanes to pipe_config Daniel Vetter
2013-04-29 10:17   ` Imre Deak
2013-04-19  9:24 ` [PATCH 09/15] drm/i915: hw state readout support for pipe_config->fdi_lanes Daniel Vetter
2013-04-24 11:23   ` Ville Syrjälä
2013-04-24 12:49     ` Daniel Vetter
2013-04-24 13:30     ` [PATCH] " Daniel Vetter
2013-04-29 10:22       ` Imre Deak
2013-04-29 17:33         ` [PATCH] drm/i915: put the right cpu_transcoder into pipe_config for hw state readout Daniel Vetter
2013-04-29 17:33         ` [PATCH] drm/i915: hw state readout support for pipe_config->fdi_lanes Daniel Vetter
2013-04-19  9:24 ` [PATCH 10/15] drm/i915: split up fdi_set_m_n into computation and hw setup Daniel Vetter
2013-04-24 11:26   ` Ville Syrjälä
2013-04-19  9:24 ` [PATCH 11/15] drm/i915: compute fdi lane config earlier Daniel Vetter
2013-04-29 12:13   ` Imre Deak
2013-04-19  9:24 ` [PATCH 12/15] drm/i915: Split up ironlake_check_fdi_lanes Daniel Vetter
2013-04-29 12:19   ` Imre Deak
2013-04-19  9:24 ` [PATCH 13/15] drm/i915: move fdi lane configuration checks ahead Daniel Vetter
2013-04-22 10:32   ` Ville Syrjälä [this message]
2013-04-22 15:13     ` [PATCH] " Daniel Vetter
2013-04-29 12:31       ` Imre Deak
2013-04-29 17:34         ` Daniel Vetter
2013-04-19  9:24 ` [PATCH 14/15] drm/i915: don't count cpu ports for fdi B/C lane sharing Daniel Vetter
2013-04-29 13:00   ` Imre Deak
2013-04-19  9:24 ` [PATCH 15/15] drm/i915: implement fdi auto-dithering Daniel Vetter
2013-04-29 14:02   ` Imre Deak
2013-04-29 14:43     ` Daniel Vetter
2013-04-29 14:59       ` Imre Deak
2013-04-29 19:35         ` Daniel Vetter
2013-04-19 15:05 ` [PATCH 00/15] high-bpp fixes and fdi auto dithering Chris Wilson
2013-04-25 10:28 ` Jani Nikula
2013-04-29 19:51   ` Daniel Vetter

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20130422103237.GY4469@intel.com \
    --to=ville.syrjala@linux.intel.com \
    --cc=daniel.vetter@ffwll.ch \
    --cc=intel-gfx@lists.freedesktop.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox