Intel-GFX Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Ramalingam C <ramalingam.c@intel.com>
To: Matt Roper <matthew.d.roper@intel.com>
Cc: intel-gfx <intel-gfx@lists.freedesktop.org>,
	Lucas De Marchi <lucas.demarchi@intel.com>,
	dri-devel <dri-devel@lists.freedesktop.org>
Subject: Re: [Intel-gfx] [PATCH 1/3] drm/i915/dg2: Enable 5th display
Date: Thu, 17 Feb 2022 23:16:54 +0530	[thread overview]
Message-ID: <20220217174654.GB11187@intel.com> (raw)
In-Reply-To: <Yg552yKPy9nhDWIH@mdroper-desk1.amr.corp.intel.com>

On 2022-02-17 at 08:37:47 -0800, Matt Roper wrote:
> Since it apparently caused some confusion on various websites, maybe we
> should change the title of the patch to "Enable 5th port" to make it
> more clear that this is only a port, not a pipe.
Ok sure.

> 
> Also, I believe one last line that we need to add to this patch is an
> intel_ddi_init() call for TC1 in the intel_setup_outputs() function.  I
> think I previously had that in a separate patch, but it went missing
> when we reorganized and refactored some of these patches

like 

diff --git a/drivers/gpu/drm/i915/display/intel_display.c b/drivers/gpu/drm/i915/display/intel_display.c
index 59961621fe4a..18531ffd4789 100644
--- a/drivers/gpu/drm/i915/display/intel_display.c
+++ b/drivers/gpu/drm/i915/display/intel_display.c
@@ -8760,6 +8760,7 @@ static void intel_setup_outputs(struct drm_i915_private *dev_priv)
                intel_ddi_init(dev_priv, PORT_B);
                intel_ddi_init(dev_priv, PORT_C);
                intel_ddi_init(dev_priv, PORT_D_XELPD);
+               intel_ddi_init(dev_priv, PORT_TC1);
        } else if (IS_ALDERLAKE_P(dev_priv)) {
                intel_ddi_init(dev_priv, PORT_A);
                intel_ddi_init(dev_priv, PORT_B);

Ram
> 
> 
> Matt
> 
> On Tue, Feb 15, 2022 at 11:21:52AM +0530, Ramalingam C wrote:
> > From: Matt Roper <matthew.d.roper@intel.com>
> > 
> > DG2 supports a 5th display output which the hardware refers to as "TC1,"
> > even though it isn't a Type-C output.  This behaves similarly to the TC1
> > on past platforms with just a couple minor differences:
> > 
> >  * DG2's TC1 bit in SDEISR is at bit 25 rather than 24 as it is on
> >    ICP/TGP/ADP.
> >  * DG2 doesn't need the hpd inversion setting that we had to use on DG1
> > 
> > Cc: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
> > Cc: Lucas De Marchi <lucas.demarchi@intel.com>
> > Cc: José Roberto de Souza <jose.souza@intel.com>
> > Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
> > Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
> > ---
> >  drivers/gpu/drm/i915/display/intel_gmbus.c | 16 ++++++++++++++--
> >  drivers/gpu/drm/i915/i915_irq.c            |  5 ++++-
> >  drivers/gpu/drm/i915/i915_reg.h            |  1 +
> >  3 files changed, 19 insertions(+), 3 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/i915/display/intel_gmbus.c b/drivers/gpu/drm/i915/display/intel_gmbus.c
> > index 6ce8c10fe975..2fad03250661 100644
> > --- a/drivers/gpu/drm/i915/display/intel_gmbus.c
> > +++ b/drivers/gpu/drm/i915/display/intel_gmbus.c
> > @@ -98,11 +98,21 @@ static const struct gmbus_pin gmbus_pins_dg1[] = {
> >  	[GMBUS_PIN_4_CNP] = { "dpd", GPIOE },
> >  };
> >  
> > +static const struct gmbus_pin gmbus_pins_dg2[] = {
> > +	[GMBUS_PIN_1_BXT] = { "dpa", GPIOB },
> > +	[GMBUS_PIN_2_BXT] = { "dpb", GPIOC },
> > +	[GMBUS_PIN_3_BXT] = { "dpc", GPIOD },
> > +	[GMBUS_PIN_4_CNP] = { "dpd", GPIOE },
> > +	[GMBUS_PIN_9_TC1_ICP] = { "tc1", GPIOJ },
> > +};
> > +
> >  /* pin is expected to be valid */
> >  static const struct gmbus_pin *get_gmbus_pin(struct drm_i915_private *dev_priv,
> >  					     unsigned int pin)
> >  {
> > -	if (INTEL_PCH_TYPE(dev_priv) >= PCH_DG1)
> > +	if (INTEL_PCH_TYPE(dev_priv) >= PCH_DG2)
> > +		return &gmbus_pins_dg2[pin];
> > +	else if (INTEL_PCH_TYPE(dev_priv) >= PCH_DG1)
> >  		return &gmbus_pins_dg1[pin];
> >  	else if (INTEL_PCH_TYPE(dev_priv) >= PCH_ICP)
> >  		return &gmbus_pins_icp[pin];
> > @@ -123,7 +133,9 @@ bool intel_gmbus_is_valid_pin(struct drm_i915_private *dev_priv,
> >  {
> >  	unsigned int size;
> >  
> > -	if (INTEL_PCH_TYPE(dev_priv) >= PCH_DG1)
> > +	if (INTEL_PCH_TYPE(dev_priv) >= PCH_DG2)
> > +		size = ARRAY_SIZE(gmbus_pins_dg2);
> > +	else if (INTEL_PCH_TYPE(dev_priv) >= PCH_DG1)
> >  		size = ARRAY_SIZE(gmbus_pins_dg1);
> >  	else if (INTEL_PCH_TYPE(dev_priv) >= PCH_ICP)
> >  		size = ARRAY_SIZE(gmbus_pins_icp);
> > diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
> > index fdd568ba4a16..4d81063b128c 100644
> > --- a/drivers/gpu/drm/i915/i915_irq.c
> > +++ b/drivers/gpu/drm/i915/i915_irq.c
> > @@ -179,6 +179,7 @@ static const u32 hpd_sde_dg1[HPD_NUM_PINS] = {
> >  	[HPD_PORT_B] = SDE_DDI_HOTPLUG_ICP(HPD_PORT_B),
> >  	[HPD_PORT_C] = SDE_DDI_HOTPLUG_ICP(HPD_PORT_C),
> >  	[HPD_PORT_D] = SDE_DDI_HOTPLUG_ICP(HPD_PORT_D),
> > +	[HPD_PORT_TC1] = SDE_TC_HOTPLUG_DG2(HPD_PORT_TC1),
> >  };
> >  
> >  static void intel_hpd_init_pins(struct drm_i915_private *dev_priv)
> > @@ -4424,7 +4425,9 @@ void intel_irq_init(struct drm_i915_private *dev_priv)
> >  		if (I915_HAS_HOTPLUG(dev_priv))
> >  			dev_priv->hotplug_funcs = &i915_hpd_funcs;
> >  	} else {
> > -		if (HAS_PCH_DG1(dev_priv))
> > +		if (HAS_PCH_DG2(dev_priv))
> > +			dev_priv->hotplug_funcs = &icp_hpd_funcs;
> > +		else if (HAS_PCH_DG1(dev_priv))
> >  			dev_priv->hotplug_funcs = &dg1_hpd_funcs;
> >  		else if (DISPLAY_VER(dev_priv) >= 11)
> >  			dev_priv->hotplug_funcs = &gen11_hpd_funcs;
> > diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
> > index 4ea1713e6b60..4d12abb2d7ff 100644
> > --- a/drivers/gpu/drm/i915/i915_reg.h
> > +++ b/drivers/gpu/drm/i915/i915_reg.h
> > @@ -6182,6 +6182,7 @@
> >  /* south display engine interrupt: ICP/TGP */
> >  #define SDE_GMBUS_ICP			(1 << 23)
> >  #define SDE_TC_HOTPLUG_ICP(hpd_pin)	REG_BIT(24 + _HPD_PIN_TC(hpd_pin))
> > +#define SDE_TC_HOTPLUG_DG2(hpd_pin)	REG_BIT(25 + _HPD_PIN_TC(hpd_pin)) /* sigh */
> >  #define SDE_DDI_HOTPLUG_ICP(hpd_pin)	REG_BIT(16 + _HPD_PIN_DDI(hpd_pin))
> >  #define SDE_DDI_HOTPLUG_MASK_ICP	(SDE_DDI_HOTPLUG_ICP(HPD_PORT_D) | \
> >  					 SDE_DDI_HOTPLUG_ICP(HPD_PORT_C) | \
> > -- 
> > 2.20.1
> > 
> 
> -- 
> Matt Roper
> Graphics Software Engineer
> VTT-OSGC Platform Enablement
> Intel Corporation
> (916) 356-2795

  reply	other threads:[~2022-02-17 17:47 UTC|newest]

Thread overview: 28+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-02-15  5:51 [Intel-gfx] [PATCH 0/3] drm/i915/dg2: 5th Display output Ramalingam C
2022-02-15  5:51 ` [Intel-gfx] [PATCH 1/3] drm/i915/dg2: Enable 5th display Ramalingam C
2022-02-16  8:02   ` Shankar, Uma
2022-02-17 16:33     ` Matt Roper
2022-02-17 16:37   ` Matt Roper
2022-02-17 17:46     ` Ramalingam C [this message]
2022-02-17 18:42   ` [Intel-gfx] [PATCH v2 1/3] drm/i915/dg2: Enable 5th port Ramalingam C
2022-02-17 21:15     ` Lucas De Marchi
2022-02-15  5:51 ` [Intel-gfx] [PATCH 2/3] drm/i915/dg2: Drop 38.4 MHz MPLLB tables Ramalingam C
2022-02-16  8:06   ` Shankar, Uma
2022-02-17 19:35   ` Lucas De Marchi
2022-02-15  5:51 ` [Intel-gfx] [PATCH 3/3] drm/i915: Fix for PHY_MISC_TC1 offset Ramalingam C
2022-02-16  8:16   ` Shankar, Uma
2022-02-16  8:50   ` Ville Syrjälä
2022-02-16  9:36     ` Hogander, Jouni
2022-02-16 10:07       ` Ville Syrjälä
2022-02-16 14:11         ` Hogander, Jouni
2022-02-16 15:01           ` Ville Syrjälä
2022-02-17 12:56             ` Ville Syrjälä
2022-02-17 20:46       ` Lucas De Marchi
2022-02-17 19:38   ` Lucas De Marchi
2022-02-16  5:01 ` [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for drm/i915/dg2: 5th Display output Patchwork
2022-02-16  5:02 ` [Intel-gfx] ✗ Fi.CI.SPARSE: " Patchwork
2022-02-16  5:36 ` [Intel-gfx] ✗ Fi.CI.BAT: failure " Patchwork
2022-02-18  2:33 ` [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for drm/i915/dg2: 5th Display output (rev3) Patchwork
2022-02-18  2:34 ` [Intel-gfx] ✗ Fi.CI.SPARSE: " Patchwork
2022-02-18  3:02 ` [Intel-gfx] ✓ Fi.CI.BAT: success " Patchwork
2022-02-18 13:49 ` [Intel-gfx] ✓ Fi.CI.IGT: " Patchwork

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220217174654.GB11187@intel.com \
    --to=ramalingam.c@intel.com \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=intel-gfx@lists.freedesktop.org \
    --cc=lucas.demarchi@intel.com \
    --cc=matthew.d.roper@intel.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox