From: Jani Nikula <jani.nikula@linux.intel.com>
To: Ville Syrjala <ville.syrjala@linux.intel.com>,
intel-gfx@lists.freedesktop.org
Subject: Re: [Intel-gfx] [PATCH v2 3/8] drm/i915: Clean up bxt/glk PLL registers
Date: Wed, 09 Mar 2022 11:22:54 +0200 [thread overview]
Message-ID: <877d931nv5.fsf@intel.com> (raw)
In-Reply-To: <20220307233940.4161-4-ville.syrjala@linux.intel.com>
On Tue, 08 Mar 2022, Ville Syrjala <ville.syrjala@linux.intel.com> wrote:
> From: Ville Syrjälä <ville.syrjala@linux.intel.com>
>
> Use REG_BIT() & co. for bxt/glk PLL registers.
>
> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
> ---
> drivers/gpu/drm/i915/display/intel_dpll_mgr.c | 32 +++++-----
> drivers/gpu/drm/i915/gvt/handlers.c | 15 +++--
> drivers/gpu/drm/i915/i915_reg.h | 61 ++++++++++---------
> 3 files changed, 57 insertions(+), 51 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/display/intel_dpll_mgr.c b/drivers/gpu/drm/i915/display/intel_dpll_mgr.c
> index 4595795d694f..2a88c6fa1f34 100644
> --- a/drivers/gpu/drm/i915/display/intel_dpll_mgr.c
> +++ b/drivers/gpu/drm/i915/display/intel_dpll_mgr.c
> @@ -1898,7 +1898,7 @@ static void bxt_ddi_pll_enable(struct drm_i915_private *dev_priv,
>
> /* Write M2 integer */
> temp = intel_de_read(dev_priv, BXT_PORT_PLL(phy, ch, 0));
> - temp &= ~PORT_PLL_M2_MASK;
> + temp &= ~PORT_PLL_M2_INT_MASK;
> temp |= pll->state.hw_state.pll0;
> intel_de_write(dev_priv, BXT_PORT_PLL(phy, ch, 0), temp);
>
> @@ -2034,7 +2034,7 @@ static bool bxt_ddi_pll_get_hw_state(struct drm_i915_private *dev_priv,
> hw_state->ebb4 &= PORT_PLL_10BIT_CLK_ENABLE;
>
> hw_state->pll0 = intel_de_read(dev_priv, BXT_PORT_PLL(phy, ch, 0));
> - hw_state->pll0 &= PORT_PLL_M2_MASK;
> + hw_state->pll0 &= PORT_PLL_M2_INT_MASK;
>
> hw_state->pll1 = intel_de_read(dev_priv, BXT_PORT_PLL(phy, ch, 1));
> hw_state->pll1 &= PORT_PLL_N_MASK;
> @@ -2200,23 +2200,23 @@ static bool bxt_ddi_set_dpll_hw_state(struct intel_crtc_state *crtc_state,
> lanestagger = 0x02;
>
> dpll_hw_state->ebb0 = PORT_PLL_P1(clk_div->p1) | PORT_PLL_P2(clk_div->p2);
> - dpll_hw_state->pll0 = clk_div->m2_int;
> + dpll_hw_state->pll0 = PORT_PLL_M2_INT(clk_div->m2_int);
> dpll_hw_state->pll1 = PORT_PLL_N(clk_div->n);
> - dpll_hw_state->pll2 = clk_div->m2_frac;
> + dpll_hw_state->pll2 = PORT_PLL_M2_FRAC(clk_div->m2_frac);
>
> if (clk_div->m2_frac)
> dpll_hw_state->pll3 = PORT_PLL_M2_FRAC_ENABLE;
>
> - dpll_hw_state->pll6 = prop_coef | PORT_PLL_INT_COEFF(int_coef);
> - dpll_hw_state->pll6 |= PORT_PLL_GAIN_CTL(gain_ctl);
> + dpll_hw_state->pll6 = PORT_PLL_PROP_COEFF(prop_coef) |
> + PORT_PLL_INT_COEFF(int_coef) |
> + PORT_PLL_GAIN_CTL(gain_ctl);
>
> - dpll_hw_state->pll8 = targ_cnt;
> + dpll_hw_state->pll8 = PORT_PLL_TARGET_CNT(targ_cnt);
>
> - dpll_hw_state->pll9 = 5 << PORT_PLL_LOCK_THRESHOLD_SHIFT;
> + dpll_hw_state->pll9 = PORT_PLL_LOCK_THRESHOLD(5);
>
> - dpll_hw_state->pll10 =
> - PORT_PLL_DCO_AMP(PORT_PLL_DCO_AMP_DEFAULT)
> - | PORT_PLL_DCO_AMP_OVR_EN_H;
> + dpll_hw_state->pll10 = PORT_PLL_DCO_AMP(15) |
> + PORT_PLL_DCO_AMP_OVR_EN_H;
>
> dpll_hw_state->ebb4 = PORT_PLL_10BIT_CLK_ENABLE;
>
> @@ -2252,12 +2252,12 @@ static int bxt_ddi_pll_get_freq(struct drm_i915_private *i915,
> struct dpll clock;
>
> clock.m1 = 2;
> - clock.m2 = (pll_state->pll0 & PORT_PLL_M2_MASK) << 22;
> + clock.m2 = REG_FIELD_GET(PORT_PLL_M2_INT_MASK, pll_state->pll0) << 22;
> if (pll_state->pll3 & PORT_PLL_M2_FRAC_ENABLE)
> - clock.m2 |= pll_state->pll2 & PORT_PLL_M2_FRAC_MASK;
> - clock.n = (pll_state->pll1 & PORT_PLL_N_MASK) >> PORT_PLL_N_SHIFT;
> - clock.p1 = (pll_state->ebb0 & PORT_PLL_P1_MASK) >> PORT_PLL_P1_SHIFT;
> - clock.p2 = (pll_state->ebb0 & PORT_PLL_P2_MASK) >> PORT_PLL_P2_SHIFT;
> + clock.m2 |= REG_FIELD_GET(PORT_PLL_M2_FRAC_MASK, pll_state->pll2);
> + clock.n = REG_FIELD_GET(PORT_PLL_N_MASK, pll_state->pll1);
> + clock.p1 = REG_FIELD_GET(PORT_PLL_P1_MASK, pll_state->ebb0);
> + clock.p2 = REG_FIELD_GET(PORT_PLL_P2_MASK, pll_state->ebb0);
>
> return chv_calc_dpll_params(i915->dpll.ref_clks.nssc, &clock);
> }
> diff --git a/drivers/gpu/drm/i915/gvt/handlers.c b/drivers/gpu/drm/i915/gvt/handlers.c
> index efdd2f3f9d73..0ee3ecc83234 100644
> --- a/drivers/gpu/drm/i915/gvt/handlers.c
> +++ b/drivers/gpu/drm/i915/gvt/handlers.c
> @@ -576,12 +576,17 @@ static u32 bxt_vgpu_get_dp_bitrate(struct intel_vgpu *vgpu, enum port port)
> }
>
> clock.m1 = 2;
> - clock.m2 = (vgpu_vreg_t(vgpu, BXT_PORT_PLL(phy, ch, 0)) & PORT_PLL_M2_MASK) << 22;
> + clock.m2 = REG_FIELD_GET(PORT_PLL_M2_INT_MASK,
> + vgpu_vreg_t(vgpu, BXT_PORT_PLL(phy, ch, 0))) << 22;
> if (vgpu_vreg_t(vgpu, BXT_PORT_PLL(phy, ch, 3)) & PORT_PLL_M2_FRAC_ENABLE)
> - clock.m2 |= vgpu_vreg_t(vgpu, BXT_PORT_PLL(phy, ch, 2)) & PORT_PLL_M2_FRAC_MASK;
> - clock.n = (vgpu_vreg_t(vgpu, BXT_PORT_PLL(phy, ch, 1)) & PORT_PLL_N_MASK) >> PORT_PLL_N_SHIFT;
> - clock.p1 = (vgpu_vreg_t(vgpu, BXT_PORT_PLL_EBB_0(phy, ch)) & PORT_PLL_P1_MASK) >> PORT_PLL_P1_SHIFT;
> - clock.p2 = (vgpu_vreg_t(vgpu, BXT_PORT_PLL_EBB_0(phy, ch)) & PORT_PLL_P2_MASK) >> PORT_PLL_P2_SHIFT;
> + clock.m2 |= REG_FIELD_GET(PORT_PLL_M2_FRAC_MASK,
> + vgpu_vreg_t(vgpu, BXT_PORT_PLL(phy, ch, 2)));
> + clock.n = REG_FIELD_GET(PORT_PLL_N_MASK,
> + vgpu_vreg_t(vgpu, BXT_PORT_PLL(phy, ch, 1)));
> + clock.p1 = REG_FIELD_GET(PORT_PLL_P1_MASK,
> + vgpu_vreg_t(vgpu, BXT_PORT_PLL_EBB_0(phy, ch)));
> + clock.p2 = REG_FIELD_GET(PORT_PLL_P2_MASK,
> + vgpu_vreg_t(vgpu, BXT_PORT_PLL_EBB_0(phy, ch)));
> clock.m = clock.m1 * clock.m2;
> clock.p = clock.p1 * clock.p2 * 5;
>
> diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
> index 70484f6f2b8b..80be197cd6eb 100644
> --- a/drivers/gpu/drm/i915/i915_reg.h
> +++ b/drivers/gpu/drm/i915/i915_reg.h
> @@ -644,22 +644,20 @@
> #define _PORT_PLL_A 0x46074
> #define _PORT_PLL_B 0x46078
> #define _PORT_PLL_C 0x4607c
> -#define PORT_PLL_ENABLE (1 << 31)
> -#define PORT_PLL_LOCK (1 << 30)
> -#define PORT_PLL_REF_SEL (1 << 27)
> -#define PORT_PLL_POWER_ENABLE (1 << 26)
> -#define PORT_PLL_POWER_STATE (1 << 25)
> +#define PORT_PLL_ENABLE REG_BIT(31)
> +#define PORT_PLL_LOCK REG_BIT(30)
> +#define PORT_PLL_REF_SEL REG_BIT(27)
> +#define PORT_PLL_POWER_ENABLE REG_BIT(26)
> +#define PORT_PLL_POWER_STATE REG_BIT(25)
> #define BXT_PORT_PLL_ENABLE(port) _MMIO_PORT(port, _PORT_PLL_A, _PORT_PLL_B)
>
> #define _PORT_PLL_EBB_0_A 0x162034
> #define _PORT_PLL_EBB_0_B 0x6C034
> #define _PORT_PLL_EBB_0_C 0x6C340
> -#define PORT_PLL_P1_SHIFT 13
> -#define PORT_PLL_P1_MASK (0x07 << PORT_PLL_P1_SHIFT)
> -#define PORT_PLL_P1(x) ((x) << PORT_PLL_P1_SHIFT)
> -#define PORT_PLL_P2_SHIFT 8
> -#define PORT_PLL_P2_MASK (0x1f << PORT_PLL_P2_SHIFT)
> -#define PORT_PLL_P2(x) ((x) << PORT_PLL_P2_SHIFT)
> +#define PORT_PLL_P1_MASK REG_GENMASK(15, 13)
> +#define PORT_PLL_P1(p1) REG_FIELD_PREP(PORT_PLL_P1_MASK, (p1))
> +#define PORT_PLL_P2_MASK REG_GENMASK(12, 8)
> +#define PORT_PLL_P2(p2) REG_FIELD_PREP(PORT_PLL_P2_MASK, (p2))
> #define BXT_PORT_PLL_EBB_0(phy, ch) _MMIO_BXT_PHY_CH(phy, ch, \
> _PORT_PLL_EBB_0_B, \
> _PORT_PLL_EBB_0_C)
> @@ -667,8 +665,8 @@
> #define _PORT_PLL_EBB_4_A 0x162038
> #define _PORT_PLL_EBB_4_B 0x6C038
> #define _PORT_PLL_EBB_4_C 0x6C344
> -#define PORT_PLL_10BIT_CLK_ENABLE (1 << 13)
> -#define PORT_PLL_RECALIBRATE (1 << 14)
> +#define PORT_PLL_RECALIBRATE REG_BIT(14)
> +#define PORT_PLL_10BIT_CLK_ENABLE REG_BIT(13)
> #define BXT_PORT_PLL_EBB_4(phy, ch) _MMIO_BXT_PHY_CH(phy, ch, \
> _PORT_PLL_EBB_4_B, \
> _PORT_PLL_EBB_4_C)
> @@ -677,31 +675,34 @@
> #define _PORT_PLL_0_B 0x6C100
> #define _PORT_PLL_0_C 0x6C380
> /* PORT_PLL_0_A */
> -#define PORT_PLL_M2_MASK 0xFF
> +#define PORT_PLL_M2_INT_MASK REG_GENMASK(7, 0)
> +#define PORT_PLL_M2_INT(m2_int) REG_FIELD_PREP(PORT_PLL_M2_INT_MASK, (m2_int))
> /* PORT_PLL_1_A */
> -#define PORT_PLL_N_SHIFT 8
> -#define PORT_PLL_N_MASK (0x0F << PORT_PLL_N_SHIFT)
> -#define PORT_PLL_N(x) ((x) << PORT_PLL_N_SHIFT)
> +#define PORT_PLL_N_MASK REG_GENMASK(11, 8)
> +#define PORT_PLL_N(n) REG_FIELD_PREP(PORT_PLL_N_MASK, (n))
> /* PORT_PLL_2_A */
> -#define PORT_PLL_M2_FRAC_MASK 0x3FFFFF
> +#define PORT_PLL_M2_FRAC_MASK REG_GENMASK(21, 0)
> +#define PORT_PLL_M2_FRAC(m2_frac) REG_FIELD_PREP(PORT_PLL_M2_FRAC_MASK, (m2_frac))
> /* PORT_PLL_3_A */
> -#define PORT_PLL_M2_FRAC_ENABLE (1 << 16)
> +#define PORT_PLL_M2_FRAC_ENABLE REG_BIT(16)
> /* PORT_PLL_6_A */
> -#define PORT_PLL_PROP_COEFF_MASK 0xF
> -#define PORT_PLL_INT_COEFF_MASK (0x1F << 8)
> -#define PORT_PLL_INT_COEFF(x) ((x) << 8)
> -#define PORT_PLL_GAIN_CTL_MASK (0x07 << 16)
> -#define PORT_PLL_GAIN_CTL(x) ((x) << 16)
> +#define PORT_PLL_PROP_COEFF_MASK REG_GENMASK(3, 0)
> +#define PORT_PLL_PROP_COEFF(x) REG_FIELD_PREP(PORT_PLL_PROP_COEFF_MASK, (x))
> +#define PORT_PLL_INT_COEFF_MASK REG_GENMASK(12, 8)
> +#define PORT_PLL_INT_COEFF(x) REG_FIELD_PREP(PORT_PLL_INT_COEFF_MASK, (x))
> +#define PORT_PLL_GAIN_CTL_MASK REG_GENMASK(18, 16)
> +#define PORT_PLL_GAIN_CTL(x) REG_FIELD_PREP(PORT_PLL_GAIN_CTL_MASK, (x))
> /* PORT_PLL_8_A */
> -#define PORT_PLL_TARGET_CNT_MASK 0x3FF
> +#define PORT_PLL_TARGET_CNT_MASK REG_GENMASK(9, 0)
> +#define PORT_PLL_TARGET_CNT(x) REG_FIELD_PREP(PORT_PLL_TARGET_CNT_MASK, (x))
> /* PORT_PLL_9_A */
> -#define PORT_PLL_LOCK_THRESHOLD_SHIFT 1
> -#define PORT_PLL_LOCK_THRESHOLD_MASK (0x7 << PORT_PLL_LOCK_THRESHOLD_SHIFT)
> +#define PORT_PLL_LOCK_THRESHOLD_MASK REG_GENMASK(3, 1)
> +#define PORT_PLL_LOCK_THRESHOLD(x) REG_FIELD_PREP(PORT_PLL_LOCK_THRESHOLD_MASK, (x))
> /* PORT_PLL_10_A */
> -#define PORT_PLL_DCO_AMP_OVR_EN_H (1 << 27)
> +#define PORT_PLL_DCO_AMP_OVR_EN_H REG_BIT(27)
> #define PORT_PLL_DCO_AMP_DEFAULT 15
> -#define PORT_PLL_DCO_AMP_MASK 0x3c00
> -#define PORT_PLL_DCO_AMP(x) ((x) << 10)
> +#define PORT_PLL_DCO_AMP_MASK REG_GENMASK(13, 10)
> +#define PORT_PLL_DCO_AMP(x) REG_FIELD_PREP(PORT_PLL_DCO_AMP_MASK, (x))
> #define _PORT_PLL_BASE(phy, ch) _BXT_PHY_CH(phy, ch, \
> _PORT_PLL_0_B, \
> _PORT_PLL_0_C)
--
Jani Nikula, Intel Open Source Graphics Center
next prev parent reply other threads:[~2022-03-09 9:23 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-03-07 23:39 [Intel-gfx] [PATCH v2 0/8] drm/i915: Clean up some dpll stuff Ville Syrjala
2022-03-07 23:39 ` [Intel-gfx] [PATCH v2 1/8] drm/i915: Store the /5 target clock in struct dpll on vlv/chv Ville Syrjala
2022-03-09 9:53 ` Jani Nikula
2022-03-09 21:43 ` [Intel-gfx] [PATCH v3 " Ville Syrjala
2022-03-07 23:39 ` [Intel-gfx] [PATCH v2 2/8] drm/i915: Remove redundant/wrong comments Ville Syrjala
2022-03-09 9:50 ` Jani Nikula
2022-03-07 23:39 ` [Intel-gfx] [PATCH v2 3/8] drm/i915: Clean up bxt/glk PLL registers Ville Syrjala
2022-03-09 9:22 ` Jani Nikula [this message]
2022-03-07 23:39 ` [Intel-gfx] [PATCH v2 4/8] drm/i915: Store the m2 divider as a whole in bxt_clk_div Ville Syrjala
2022-03-09 9:27 ` Jani Nikula
2022-03-07 23:39 ` [Intel-gfx] [PATCH v2 5/8] drm/i915: Replace bxt_clk_div with struct dpll Ville Syrjala
2022-03-07 23:39 ` [Intel-gfx] [PATCH v2 6/8] drm/i915: Replace hand rolled bxt vco calculation with chv_calc_dpll_params() Ville Syrjala
2022-03-09 9:46 ` Jani Nikula
2022-03-07 23:39 ` [Intel-gfx] [PATCH v2 7/8] drm/i915: Populate bxt/glk DPLL clock limits a bit more Ville Syrjala
2022-03-09 9:30 ` Jani Nikula
2022-03-07 23:39 ` [Intel-gfx] [PATCH v2 8/8] drm/i915: Remove struct dp_link_dpll Ville Syrjala
2022-03-09 9:34 ` Jani Nikula
2022-03-07 23:50 ` [Intel-gfx] ✗ Fi.CI.SPARSE: warning for drm/i915: Clean up some dpll stuff (rev3) Patchwork
2022-03-08 13:31 ` [Intel-gfx] ✗ Fi.CI.BAT: failure " Patchwork
2022-03-09 2:48 ` [Intel-gfx] ✗ Fi.CI.SPARSE: warning for drm/i915: Clean up some dpll stuff (rev4) Patchwork
2022-03-09 3:22 ` [Intel-gfx] ✗ Fi.CI.BAT: failure " Patchwork
2022-03-09 18:23 ` [Intel-gfx] ✗ Fi.CI.SPARSE: warning for drm/i915: Clean up some dpll stuff (rev5) Patchwork
2022-03-09 18:59 ` [Intel-gfx] ✗ Fi.CI.BAT: failure " Patchwork
2022-03-09 22:02 ` [Intel-gfx] ✗ Fi.CI.SPARSE: warning for drm/i915: Clean up some dpll stuff (rev6) Patchwork
2022-03-09 22:35 ` [Intel-gfx] ✓ Fi.CI.BAT: success " Patchwork
2022-03-10 7:29 ` [Intel-gfx] ✗ Fi.CI.IGT: failure " Patchwork
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=877d931nv5.fsf@intel.com \
--to=jani.nikula@linux.intel.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=ville.syrjala@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox