* [Intel-wired-lan] [PATCH S32 02/15] ice: Add NDO callback to set the maximum per-queue bitrate
2019-10-25 14:34 [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and ice_dis_vsi in DCB configuration flow Tony Nguyen
@ 2019-10-25 14:34 ` Tony Nguyen
2019-11-01 16:41 ` Bowers, AndrewX
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 03/15] ice: Implement DCBNL support Tony Nguyen
` (13 subsequent siblings)
14 siblings, 1 reply; 30+ messages in thread
From: Tony Nguyen @ 2019-10-25 14:34 UTC (permalink / raw)
To: intel-wired-lan
From: Usha Ketineni <usha.k.ketineni@intel.com>
Allow for rate limiting Tx queues. Bitrate is set in
Mbps(megabits per second).
Mbps max-rate is set for the queue via sysfs:
/sys/class/net/<iface>/queues/tx-<queue>/tx_maxrate
ex: echo 100 >/sys/class/net/ens7/queues/tx-0/tx_maxrate
echo 200 >/sys/class/net/ens7/queues/tx-1/tx_maxrate
Note: A value of zero for tx_maxrate means disabled,
default is disabled.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
---
.../net/ethernet/intel/ice/ice_adminq_cmd.h | 46 +
drivers/net/ethernet/intel/ice/ice_common.c | 10 +-
drivers/net/ethernet/intel/ice/ice_common.h | 2 +
drivers/net/ethernet/intel/ice/ice_dcb_lib.c | 10 +
drivers/net/ethernet/intel/ice/ice_dcb_lib.h | 8 +
drivers/net/ethernet/intel/ice/ice_main.c | 43 +
drivers/net/ethernet/intel/ice/ice_sched.c | 1264 ++++++++++++++++-
drivers/net/ethernet/intel/ice/ice_sched.h | 39 +
drivers/net/ethernet/intel/ice/ice_switch.h | 5 -
drivers/net/ethernet/intel/ice/ice_type.h | 63 +-
10 files changed, 1480 insertions(+), 10 deletions(-)
diff --git a/drivers/net/ethernet/intel/ice/ice_adminq_cmd.h b/drivers/net/ethernet/intel/ice/ice_adminq_cmd.h
index f6b4d300543d..5422a2f2c8e0 100644
--- a/drivers/net/ethernet/intel/ice/ice_adminq_cmd.h
+++ b/drivers/net/ethernet/intel/ice/ice_adminq_cmd.h
@@ -742,6 +742,10 @@ struct ice_aqc_add_elem {
struct ice_aqc_txsched_elem_data generic[1];
};
+struct ice_aqc_conf_elem {
+ struct ice_aqc_txsched_elem_data generic[1];
+};
+
struct ice_aqc_get_elem {
struct ice_aqc_txsched_elem_data generic[1];
};
@@ -783,6 +787,44 @@ struct ice_aqc_port_ets_elem {
__le32 tc_node_teid[8]; /* Used for response, reserved in command */
};
+/* Rate limiting profile for
+ * Add RL profile (indirect 0x0410)
+ * Query RL profile (indirect 0x0411)
+ * Remove RL profile (indirect 0x0415)
+ * These indirect commands acts on single or multiple
+ * RL profiles with specified data.
+ */
+struct ice_aqc_rl_profile {
+ __le16 num_profiles;
+ __le16 num_processed; /* Only for response. Reserved in Command. */
+ u8 reserved[4];
+ __le32 addr_high;
+ __le32 addr_low;
+};
+
+struct ice_aqc_rl_profile_elem {
+ u8 level;
+ u8 flags;
+#define ICE_AQC_RL_PROFILE_TYPE_S 0x0
+#define ICE_AQC_RL_PROFILE_TYPE_M (0x3 << ICE_AQC_RL_PROFILE_TYPE_S)
+#define ICE_AQC_RL_PROFILE_TYPE_CIR 0
+#define ICE_AQC_RL_PROFILE_TYPE_EIR 1
+#define ICE_AQC_RL_PROFILE_TYPE_SRL 2
+/* The following flag is used for Query RL Profile Data */
+#define ICE_AQC_RL_PROFILE_INVAL_S 0x7
+#define ICE_AQC_RL_PROFILE_INVAL_M (0x1 << ICE_AQC_RL_PROFILE_INVAL_S)
+
+ __le16 profile_id;
+ __le16 max_burst_size;
+ __le16 rl_multiply;
+ __le16 wake_up_calc;
+ __le16 rl_encode;
+};
+
+struct ice_aqc_rl_profile_generic_elem {
+ struct ice_aqc_rl_profile_elem generic[1];
+};
+
/* Query Scheduler Resource Allocation (indirect 0x0412)
* This indirect command retrieves the scheduler resources allocated by
* EMP Firmware to the given PF.
@@ -1659,6 +1701,7 @@ struct ice_aq_desc {
struct ice_aqc_sched_elem_cmd sched_elem_cmd;
struct ice_aqc_query_txsched_res query_sched_res;
struct ice_aqc_query_port_ets port_ets;
+ struct ice_aqc_rl_profile rl_profile;
struct ice_aqc_nvm nvm;
struct ice_aqc_nvm_checksum nvm_checksum;
struct ice_aqc_pf_vf_msg virt;
@@ -1761,12 +1804,15 @@ enum ice_adminq_opc {
/* transmit scheduler commands */
ice_aqc_opc_get_dflt_topo = 0x0400,
ice_aqc_opc_add_sched_elems = 0x0401,
+ ice_aqc_opc_cfg_sched_elems = 0x0403,
ice_aqc_opc_get_sched_elems = 0x0404,
ice_aqc_opc_suspend_sched_elems = 0x0409,
ice_aqc_opc_resume_sched_elems = 0x040A,
ice_aqc_opc_query_port_ets = 0x040E,
ice_aqc_opc_delete_sched_elems = 0x040F,
+ ice_aqc_opc_add_rl_profiles = 0x0410,
ice_aqc_opc_query_sched_res = 0x0412,
+ ice_aqc_opc_remove_rl_profiles = 0x0415,
/* PHY commands */
ice_aqc_opc_get_phy_caps = 0x0600,
diff --git a/drivers/net/ethernet/intel/ice/ice_common.c b/drivers/net/ethernet/intel/ice/ice_common.c
index 3bc794b3376e..eb01c218c596 100644
--- a/drivers/net/ethernet/intel/ice/ice_common.c
+++ b/drivers/net/ethernet/intel/ice/ice_common.c
@@ -877,6 +877,9 @@ enum ice_status ice_init_hw(struct ice_hw *hw)
goto err_unroll_sched;
}
INIT_LIST_HEAD(&hw->agg_list);
+ /* Initialize max burst size */
+ if (!hw->max_burst_size)
+ ice_cfg_rl_burst_size(hw, ICE_SCHED_DFLT_BURST_SIZE);
status = ice_init_fltr_mgmt_struct(hw);
if (status)
@@ -3282,7 +3285,7 @@ ice_set_ctx(u8 *src_ctx, u8 *dest_ctx, const struct ice_ctx_ele *ce_info)
* @tc: TC number
* @q_handle: software queue handle
*/
-static struct ice_q_ctx *
+struct ice_q_ctx *
ice_get_lan_q_ctx(struct ice_hw *hw, u16 vsi_handle, u8 tc, u16 q_handle)
{
struct ice_vsi_ctx *vsi;
@@ -3379,9 +3382,12 @@ ice_ena_vsi_txq(struct ice_port_info *pi, u16 vsi_handle, u8 tc, u16 q_handle,
node.node_teid = buf->txqs[0].q_teid;
node.data.elem_type = ICE_AQC_ELEM_TYPE_LEAF;
q_ctx->q_handle = q_handle;
+ q_ctx->q_teid = le32_to_cpu(node.node_teid);
- /* add a leaf node into schduler tree queue layer */
+ /* add a leaf node into scheduler tree queue layer */
status = ice_sched_add_node(pi, hw->num_tx_sched_layers - 1, &node);
+ if (!status)
+ status = ice_sched_replay_q_bw(pi, q_ctx);
ena_txq_exit:
mutex_unlock(&pi->sched_lock);
diff --git a/drivers/net/ethernet/intel/ice/ice_common.h b/drivers/net/ethernet/intel/ice/ice_common.h
index d2491c947629..c17c5724d33b 100644
--- a/drivers/net/ethernet/intel/ice/ice_common.h
+++ b/drivers/net/ethernet/intel/ice/ice_common.h
@@ -145,6 +145,8 @@ ice_ena_vsi_txq(struct ice_port_info *pi, u16 vsi_handle, u8 tc, u16 q_handle,
enum ice_status ice_replay_vsi(struct ice_hw *hw, u16 vsi_handle);
void ice_replay_post(struct ice_hw *hw);
void ice_output_fw_log(struct ice_hw *hw, struct ice_aq_desc *desc, void *buf);
+struct ice_q_ctx *
+ice_get_lan_q_ctx(struct ice_hw *hw, u16 vsi_handle, u8 tc, u16 q_handle);
void
ice_stat_update40(struct ice_hw *hw, u32 reg, bool prev_stat_loaded,
u64 *prev_stat, u64 *cur_stat);
diff --git a/drivers/net/ethernet/intel/ice/ice_dcb_lib.c b/drivers/net/ethernet/intel/ice/ice_dcb_lib.c
index afe02e0aecc0..6e42e4b4c225 100644
--- a/drivers/net/ethernet/intel/ice/ice_dcb_lib.c
+++ b/drivers/net/ethernet/intel/ice/ice_dcb_lib.c
@@ -101,6 +101,16 @@ u8 ice_dcb_get_num_tc(struct ice_dcbx_cfg *dcbcfg)
return ret;
}
+/**
+ * ice_dcb_get_tc - Get the TC associated with the queue
+ * @vsi: ptr to the VSI
+ * @queue_index: queue number associated with VSI
+ */
+u8 ice_dcb_get_tc(struct ice_vsi *vsi, int queue_index)
+{
+ return vsi->tx_rings[queue_index]->dcb_tc;
+}
+
/**
* ice_vsi_cfg_dcb_rings - Update rings to reflect DCB TC
* @vsi: VSI owner of rings being updated
diff --git a/drivers/net/ethernet/intel/ice/ice_dcb_lib.h b/drivers/net/ethernet/intel/ice/ice_dcb_lib.h
index d11a0aab01ac..59e40cf2dd73 100644
--- a/drivers/net/ethernet/intel/ice/ice_dcb_lib.h
+++ b/drivers/net/ethernet/intel/ice/ice_dcb_lib.h
@@ -14,6 +14,7 @@
void ice_dcb_rebuild(struct ice_pf *pf);
u8 ice_dcb_get_ena_tc(struct ice_dcbx_cfg *dcbcfg);
u8 ice_dcb_get_num_tc(struct ice_dcbx_cfg *dcbcfg);
+u8 ice_dcb_get_tc(struct ice_vsi *vsi, int queue_index);
void ice_vsi_cfg_dcb_rings(struct ice_vsi *vsi);
int ice_init_pf_dcb(struct ice_pf *pf, bool locked);
void ice_update_dcb_stats(struct ice_pf *pf);
@@ -42,6 +43,13 @@ static inline u8 ice_dcb_get_num_tc(struct ice_dcbx_cfg __always_unused *dcbcfg)
return 1;
}
+static inline u8
+ice_dcb_get_tc(struct ice_vsi __always_unused *vsi,
+ int __always_unused queue_index)
+{
+ return 0;
+}
+
static inline int
ice_init_pf_dcb(struct ice_pf *pf, bool __always_unused locked)
{
diff --git a/drivers/net/ethernet/intel/ice/ice_main.c b/drivers/net/ethernet/intel/ice/ice_main.c
index dd05505ccbe1..fec58433bafb 100644
--- a/drivers/net/ethernet/intel/ice/ice_main.c
+++ b/drivers/net/ethernet/intel/ice/ice_main.c
@@ -3796,6 +3796,48 @@ static void ice_set_rx_mode(struct net_device *netdev)
ice_service_task_schedule(vsi->back);
}
+/**
+ * ice_set_tx_maxrate - NDO callback to set the maximum per-queue bitrate
+ * @netdev: network interface device structure
+ * @queue_index: Queue ID
+ * @maxrate: maximum bandwidth in Mbps
+ */
+static int
+ice_set_tx_maxrate(struct net_device *netdev, int queue_index, u32 maxrate)
+{
+ struct ice_netdev_priv *np = netdev_priv(netdev);
+ struct ice_vsi *vsi = np->vsi;
+ enum ice_status status;
+ u16 q_handle;
+ u8 tc;
+
+ /* Validate maxrate requested is within permitted range */
+ if (maxrate && (maxrate > (ICE_SCHED_MAX_BW / 1000))) {
+ netdev_err(netdev,
+ "Invalid max rate %d specified for the queue %d\n",
+ maxrate, queue_index);
+ return -EINVAL;
+ }
+
+ q_handle = vsi->tx_rings[queue_index]->q_handle;
+ tc = ice_dcb_get_tc(vsi, queue_index);
+
+ /* Set BW back to default, when user set maxrate to 0 */
+ if (!maxrate)
+ status = ice_cfg_q_bw_dflt_lmt(vsi->port_info, vsi->idx, tc,
+ q_handle, ICE_MAX_BW);
+ else
+ status = ice_cfg_q_bw_lmt(vsi->port_info, vsi->idx, tc,
+ q_handle, ICE_MAX_BW, maxrate * 1000);
+ if (status) {
+ netdev_err(netdev,
+ "Unable to set Tx max rate, error %d\n", status);
+ return -EIO;
+ }
+
+ return 0;
+}
+
/**
* ice_fdb_add - add an entry to the hardware database
* @ndm: the input from the stack
@@ -5307,6 +5349,7 @@ static const struct net_device_ops ice_netdev_ops = {
.ndo_validate_addr = eth_validate_addr,
.ndo_change_mtu = ice_change_mtu,
.ndo_get_stats64 = ice_get_stats64,
+ .ndo_set_tx_maxrate = ice_set_tx_maxrate,
.ndo_set_vf_spoofchk = ice_set_vf_spoofchk,
.ndo_set_vf_mac = ice_set_vf_mac,
.ndo_get_vf_config = ice_get_vf_cfg,
diff --git a/drivers/net/ethernet/intel/ice/ice_sched.c b/drivers/net/ethernet/intel/ice/ice_sched.c
index fc624b73d05d..dac5a6712610 100644
--- a/drivers/net/ethernet/intel/ice/ice_sched.c
+++ b/drivers/net/ethernet/intel/ice/ice_sched.c
@@ -410,6 +410,27 @@ ice_aq_add_sched_elems(struct ice_hw *hw, u16 grps_req,
grps_added, cd);
}
+/**
+ * ice_aq_cfg_sched_elems - configures scheduler elements
+ * @hw: pointer to the HW struct
+ * @elems_req: number of elements to configure
+ * @buf: pointer to buffer
+ * @buf_size: buffer size in bytes
+ * @elems_cfgd: returns total number of elements configured
+ * @cd: pointer to command details structure or NULL
+ *
+ * Configure scheduling elements (0x0403)
+ */
+static enum ice_status
+ice_aq_cfg_sched_elems(struct ice_hw *hw, u16 elems_req,
+ struct ice_aqc_conf_elem *buf, u16 buf_size,
+ u16 *elems_cfgd, struct ice_sq_cd *cd)
+{
+ return ice_aqc_send_sched_elem_cmd(hw, ice_aqc_opc_cfg_sched_elems,
+ elems_req, (void *)buf, buf_size,
+ elems_cfgd, cd);
+}
+
/**
* ice_aq_suspend_sched_elems - suspend scheduler elements
* @hw: pointer to the HW struct
@@ -556,6 +577,149 @@ ice_alloc_lan_q_ctx(struct ice_hw *hw, u16 vsi_handle, u8 tc, u16 new_numqs)
return 0;
}
+/**
+ * ice_aq_rl_profile - performs a rate limiting task
+ * @hw: pointer to the HW struct
+ * @opcode:opcode for add, query, or remove profile(s)
+ * @num_profiles: the number of profiles
+ * @buf: pointer to buffer
+ * @buf_size: buffer size in bytes
+ * @num_processed: number of processed add or remove profile(s) to return
+ * @cd: pointer to command details structure
+ *
+ * RL profile function to add, query, or remove profile(s)
+ */
+static enum ice_status
+ice_aq_rl_profile(struct ice_hw *hw, enum ice_adminq_opc opcode,
+ u16 num_profiles, struct ice_aqc_rl_profile_generic_elem *buf,
+ u16 buf_size, u16 *num_processed, struct ice_sq_cd *cd)
+{
+ struct ice_aqc_rl_profile *cmd;
+ struct ice_aq_desc desc;
+ enum ice_status status;
+
+ cmd = &desc.params.rl_profile;
+
+ ice_fill_dflt_direct_cmd_desc(&desc, opcode);
+ desc.flags |= cpu_to_le16(ICE_AQ_FLAG_RD);
+ cmd->num_profiles = cpu_to_le16(num_profiles);
+ status = ice_aq_send_cmd(hw, &desc, buf, buf_size, cd);
+ if (!status && num_processed)
+ *num_processed = le16_to_cpu(cmd->num_processed);
+ return status;
+}
+
+/**
+ * ice_aq_add_rl_profile - adds rate limiting profile(s)
+ * @hw: pointer to the HW struct
+ * @num_profiles: the number of profile(s) to be add
+ * @buf: pointer to buffer
+ * @buf_size: buffer size in bytes
+ * @num_profiles_added: total number of profiles added to return
+ * @cd: pointer to command details structure
+ *
+ * Add RL profile (0x0410)
+ */
+static enum ice_status
+ice_aq_add_rl_profile(struct ice_hw *hw, u16 num_profiles,
+ struct ice_aqc_rl_profile_generic_elem *buf,
+ u16 buf_size, u16 *num_profiles_added,
+ struct ice_sq_cd *cd)
+{
+ return ice_aq_rl_profile(hw, ice_aqc_opc_add_rl_profiles,
+ num_profiles, buf,
+ buf_size, num_profiles_added, cd);
+}
+
+/**
+ * ice_aq_remove_rl_profile - removes RL profile(s)
+ * @hw: pointer to the HW struct
+ * @num_profiles: the number of profile(s) to remove
+ * @buf: pointer to buffer
+ * @buf_size: buffer size in bytes
+ * @num_profiles_removed: total number of profiles removed to return
+ * @cd: pointer to command details structure or NULL
+ *
+ * Remove RL profile (0x0415)
+ */
+static enum ice_status
+ice_aq_remove_rl_profile(struct ice_hw *hw, u16 num_profiles,
+ struct ice_aqc_rl_profile_generic_elem *buf,
+ u16 buf_size, u16 *num_profiles_removed,
+ struct ice_sq_cd *cd)
+{
+ return ice_aq_rl_profile(hw, ice_aqc_opc_remove_rl_profiles,
+ num_profiles, buf,
+ buf_size, num_profiles_removed, cd);
+}
+
+/**
+ * ice_sched_del_rl_profile - remove RL profile
+ * @hw: pointer to the HW struct
+ * @rl_info: rate limit profile information
+ *
+ * If the profile ID is not referenced anymore, it removes profile ID with
+ * its associated parameters from HW DB,and locally. The caller needs to
+ * hold scheduler lock.
+ */
+static enum ice_status
+ice_sched_del_rl_profile(struct ice_hw *hw,
+ struct ice_aqc_rl_profile_info *rl_info)
+{
+ struct ice_aqc_rl_profile_generic_elem *buf;
+ u16 num_profiles_removed;
+ enum ice_status status;
+ u16 num_profiles = 1;
+
+ if (rl_info->prof_id_ref != 0)
+ return ICE_ERR_IN_USE;
+
+ /* Safe to remove profile ID */
+ buf = (struct ice_aqc_rl_profile_generic_elem *)
+ &rl_info->profile;
+ status = ice_aq_remove_rl_profile(hw, num_profiles, buf, sizeof(*buf),
+ &num_profiles_removed, NULL);
+ if (status || num_profiles_removed != num_profiles)
+ return ICE_ERR_CFG;
+
+ /* Delete stale entry now */
+ list_del(&rl_info->list_entry);
+ devm_kfree(ice_hw_to_dev(hw), rl_info);
+ return status;
+}
+
+/**
+ * ice_sched_clear_rl_prof - clears RL prof entries
+ * @pi: port information structure
+ *
+ * This function removes all RL profile from HW as well as from SW DB.
+ */
+static void ice_sched_clear_rl_prof(struct ice_port_info *pi)
+{
+ u16 ln;
+
+ for (ln = 0; ln < pi->hw->num_tx_sched_layers; ln++) {
+ struct ice_aqc_rl_profile_info *rl_prof_elem;
+ struct ice_aqc_rl_profile_info *rl_prof_tmp;
+
+ list_for_each_entry_safe(rl_prof_elem, rl_prof_tmp,
+ &pi->rl_prof_list[ln], list_entry) {
+ struct ice_hw *hw = pi->hw;
+ enum ice_status status;
+
+ rl_prof_elem->prof_id_ref = 0;
+ status = ice_sched_del_rl_profile(hw, rl_prof_elem);
+ if (status) {
+ ice_debug(hw, ICE_DBG_SCHED,
+ "Remove rl profile failed\n");
+ /* On error, free mem required */
+ list_del(&rl_prof_elem->list_entry);
+ devm_kfree(ice_hw_to_dev(hw), rl_prof_elem);
+ }
+ }
+ }
+}
+
/**
* ice_sched_clear_agg - clears the aggregator related information
* @hw: pointer to the hardware structure
@@ -592,6 +756,8 @@ static void ice_sched_clear_tx_topo(struct ice_port_info *pi)
{
if (!pi)
return;
+ /* remove RL profiles related lists */
+ ice_sched_clear_rl_prof(pi);
if (pi->root) {
ice_free_sched_node(pi, pi->root);
pi->root = NULL;
@@ -1014,6 +1180,8 @@ enum ice_status ice_sched_init_port(struct ice_port_info *pi)
/* initialize the port for handling the scheduler tree */
pi->port_state = ICE_SCHED_PORT_STATE_READY;
mutex_init(&pi->sched_lock);
+ for (i = 0; i < ICE_AQC_TOPO_MAX_LEVEL_NUM; i++)
+ INIT_LIST_HEAD(&pi->rl_prof_list[i]);
err_init_port:
if (status && pi->root) {
@@ -1062,8 +1230,8 @@ enum ice_status ice_sched_query_res_alloc(struct ice_hw *hw)
* and so on. This array will be populated from root (index 0) to
* qgroup layer 7. Leaf node has no children.
*/
- for (i = 0; i < hw->num_tx_sched_layers; i++) {
- max_sibl = buf->layer_props[i].max_sibl_grp_sz;
+ for (i = 0; i < hw->num_tx_sched_layers - 1; i++) {
+ max_sibl = buf->layer_props[i + 1].max_sibl_grp_sz;
hw->max_children[i] = le16_to_cpu(max_sibl);
}
@@ -1670,3 +1838,1095 @@ enum ice_status ice_rm_vsi_lan_cfg(struct ice_port_info *pi, u16 vsi_handle)
{
return ice_sched_rm_vsi_cfg(pi, vsi_handle, ICE_SCHED_NODE_OWNER_LAN);
}
+
+/**
+ * ice_sched_rm_unused_rl_prof - remove unused RL profile
+ * @pi: port information structure
+ *
+ * This function removes unused rate limit profiles from the HW and
+ * SW DB. The caller needs to hold scheduler lock.
+ */
+static void ice_sched_rm_unused_rl_prof(struct ice_port_info *pi)
+{
+ u16 ln;
+
+ for (ln = 0; ln < pi->hw->num_tx_sched_layers; ln++) {
+ struct ice_aqc_rl_profile_info *rl_prof_elem;
+ struct ice_aqc_rl_profile_info *rl_prof_tmp;
+
+ list_for_each_entry_safe(rl_prof_elem, rl_prof_tmp,
+ &pi->rl_prof_list[ln], list_entry) {
+ if (!ice_sched_del_rl_profile(pi->hw, rl_prof_elem))
+ ice_debug(pi->hw, ICE_DBG_SCHED,
+ "Removed rl profile\n");
+ }
+ }
+}
+
+/**
+ * ice_sched_update_elem - update element
+ * @hw: pointer to the HW struct
+ * @node: pointer to node
+ * @info: node info to update
+ *
+ * It updates the HW DB, and local SW DB of node. It updates the scheduling
+ * parameters of node from argument info data buffer (Info->data buf) and
+ * returns success or error on config sched element failure. The caller
+ * needs to hold scheduler lock.
+ */
+static enum ice_status
+ice_sched_update_elem(struct ice_hw *hw, struct ice_sched_node *node,
+ struct ice_aqc_txsched_elem_data *info)
+{
+ struct ice_aqc_conf_elem buf;
+ enum ice_status status;
+ u16 elem_cfgd = 0;
+ u16 num_elems = 1;
+
+ buf.generic[0] = *info;
+ /* Parent TEID is reserved field in this aq call */
+ buf.generic[0].parent_teid = 0;
+ /* Element type is reserved field in this aq call */
+ buf.generic[0].data.elem_type = 0;
+ /* Flags is reserved field in this aq call */
+ buf.generic[0].data.flags = 0;
+
+ /* Update HW DB */
+ /* Configure element node */
+ status = ice_aq_cfg_sched_elems(hw, num_elems, &buf, sizeof(buf),
+ &elem_cfgd, NULL);
+ if (status || elem_cfgd != num_elems) {
+ ice_debug(hw, ICE_DBG_SCHED, "Config sched elem error\n");
+ return ICE_ERR_CFG;
+ }
+
+ /* Config success case */
+ /* Now update local SW DB */
+ /* Only copy the data portion of info buffer */
+ node->info.data = info->data;
+ return status;
+}
+
+/**
+ * ice_sched_cfg_node_bw_alloc - configure node BW weight/alloc params
+ * @hw: pointer to the HW struct
+ * @node: sched node to configure
+ * @rl_type: rate limit type CIR, EIR, or shared
+ * @bw_alloc: BW weight/allocation
+ *
+ * This function configures node element's BW allocation.
+ */
+static enum ice_status
+ice_sched_cfg_node_bw_alloc(struct ice_hw *hw, struct ice_sched_node *node,
+ enum ice_rl_type rl_type, u8 bw_alloc)
+{
+ struct ice_aqc_txsched_elem_data buf;
+ struct ice_aqc_txsched_elem *data;
+ enum ice_status status;
+
+ buf = node->info;
+ data = &buf.data;
+ if (rl_type == ICE_MIN_BW) {
+ data->valid_sections |= ICE_AQC_ELEM_VALID_CIR;
+ data->cir_bw.bw_alloc = cpu_to_le16(bw_alloc);
+ } else if (rl_type == ICE_MAX_BW) {
+ data->valid_sections |= ICE_AQC_ELEM_VALID_EIR;
+ data->eir_bw.bw_alloc = cpu_to_le16(bw_alloc);
+ } else {
+ return ICE_ERR_PARAM;
+ }
+
+ /* Configure element */
+ status = ice_sched_update_elem(hw, node, &buf);
+ return status;
+}
+
+/**
+ * ice_set_clear_cir_bw - set or clear CIR BW
+ * @bw_t_info: bandwidth type information structure
+ * @bw: bandwidth in Kbps - Kilo bits per sec
+ *
+ * Save or clear CIR bandwidth (BW) in the passed param bw_t_info.
+ */
+static void
+ice_set_clear_cir_bw(struct ice_bw_type_info *bw_t_info, u32 bw)
+{
+ if (bw == ICE_SCHED_DFLT_BW) {
+ clear_bit(ICE_BW_TYPE_CIR, bw_t_info->bw_t_bitmap);
+ bw_t_info->cir_bw.bw = 0;
+ } else {
+ /* Save type of BW information */
+ set_bit(ICE_BW_TYPE_CIR, bw_t_info->bw_t_bitmap);
+ bw_t_info->cir_bw.bw = bw;
+ }
+}
+
+/**
+ * ice_set_clear_eir_bw - set or clear EIR BW
+ * @bw_t_info: bandwidth type information structure
+ * @bw: bandwidth in Kbps - Kilo bits per sec
+ *
+ * Save or clear EIR bandwidth (BW) in the passed param bw_t_info.
+ */
+static void
+ice_set_clear_eir_bw(struct ice_bw_type_info *bw_t_info, u32 bw)
+{
+ if (bw == ICE_SCHED_DFLT_BW) {
+ clear_bit(ICE_BW_TYPE_EIR, bw_t_info->bw_t_bitmap);
+ bw_t_info->eir_bw.bw = 0;
+ } else {
+ /* EIR BW and Shared BW profiles are mutually exclusive and
+ * hence only one of them may be set for any given element.
+ * First clear earlier saved shared BW information.
+ */
+ clear_bit(ICE_BW_TYPE_SHARED, bw_t_info->bw_t_bitmap);
+ bw_t_info->shared_bw = 0;
+ /* save EIR BW information */
+ set_bit(ICE_BW_TYPE_EIR, bw_t_info->bw_t_bitmap);
+ bw_t_info->eir_bw.bw = bw;
+ }
+}
+
+/**
+ * ice_set_clear_shared_bw - set or clear shared BW
+ * @bw_t_info: bandwidth type information structure
+ * @bw: bandwidth in Kbps - Kilo bits per sec
+ *
+ * Save or clear shared bandwidth (BW) in the passed param bw_t_info.
+ */
+static void
+ice_set_clear_shared_bw(struct ice_bw_type_info *bw_t_info, u32 bw)
+{
+ if (bw == ICE_SCHED_DFLT_BW) {
+ clear_bit(ICE_BW_TYPE_SHARED, bw_t_info->bw_t_bitmap);
+ bw_t_info->shared_bw = 0;
+ } else {
+ /* EIR BW and Shared BW profiles are mutually exclusive and
+ * hence only one of them may be set for any given element.
+ * First clear earlier saved EIR BW information.
+ */
+ clear_bit(ICE_BW_TYPE_EIR, bw_t_info->bw_t_bitmap);
+ bw_t_info->eir_bw.bw = 0;
+ /* save shared BW information */
+ set_bit(ICE_BW_TYPE_SHARED, bw_t_info->bw_t_bitmap);
+ bw_t_info->shared_bw = bw;
+ }
+}
+
+/**
+ * ice_sched_calc_wakeup - calculate RL profile wakeup parameter
+ * @bw: bandwidth in Kbps
+ *
+ * This function calculates the wakeup parameter of RL profile.
+ */
+static u16 ice_sched_calc_wakeup(s32 bw)
+{
+ s64 bytes_per_sec, wakeup_int, wakeup_a, wakeup_b, wakeup_f;
+ s32 wakeup_f_int;
+ u16 wakeup = 0;
+
+ /* Get the wakeup integer value */
+ bytes_per_sec = div64_long(((s64)bw * 1000), BITS_PER_BYTE);
+ wakeup_int = div64_long(ICE_RL_PROF_FREQUENCY, bytes_per_sec);
+ if (wakeup_int > 63) {
+ wakeup = (u16)((1 << 15) | wakeup_int);
+ } else {
+ /* Calculate fraction value up to 4 decimals
+ * Convert Integer value to a constant multiplier
+ */
+ wakeup_b = (s64)ICE_RL_PROF_MULTIPLIER * wakeup_int;
+ wakeup_a = div64_long((s64)ICE_RL_PROF_MULTIPLIER *
+ ICE_RL_PROF_FREQUENCY,
+ bytes_per_sec);
+
+ /* Get Fraction value */
+ wakeup_f = wakeup_a - wakeup_b;
+
+ /* Round up the Fractional value via Ceil(Fractional value) */
+ if (wakeup_f > div64_long(ICE_RL_PROF_MULTIPLIER, 2))
+ wakeup_f += 1;
+
+ wakeup_f_int = (s32)div64_long(wakeup_f * ICE_RL_PROF_FRACTION,
+ ICE_RL_PROF_MULTIPLIER);
+ wakeup |= (u16)(wakeup_int << 9);
+ wakeup |= (u16)(0x1ff & wakeup_f_int);
+ }
+
+ return wakeup;
+}
+
+/**
+ * ice_sched_bw_to_rl_profile - convert BW to profile parameters
+ * @bw: bandwidth in Kbps
+ * @profile: profile parameters to return
+ *
+ * This function converts the BW to profile structure format.
+ */
+static enum ice_status
+ice_sched_bw_to_rl_profile(u32 bw, struct ice_aqc_rl_profile_elem *profile)
+{
+ enum ice_status status = ICE_ERR_PARAM;
+ s64 bytes_per_sec, ts_rate, mv_tmp;
+ bool found = false;
+ s32 encode = 0;
+ s64 mv = 0;
+ s32 i;
+
+ /* Bw settings range is from 0.5Mb/sec to 100Gb/sec */
+ if (bw < ICE_SCHED_MIN_BW || bw > ICE_SCHED_MAX_BW)
+ return status;
+
+ /* Bytes per second from Kbps */
+ bytes_per_sec = div64_long(((s64)bw * 1000), BITS_PER_BYTE);
+
+ /* encode is 6 bits but really useful are 5 bits */
+ for (i = 0; i < 64; i++) {
+ u64 pow_result = BIT_ULL(i);
+
+ ts_rate = div64_long((s64)ICE_RL_PROF_FREQUENCY,
+ pow_result * ICE_RL_PROF_TS_MULTIPLIER);
+ if (ts_rate <= 0)
+ continue;
+
+ /* Multiplier value */
+ mv_tmp = div64_long(bytes_per_sec * ICE_RL_PROF_MULTIPLIER,
+ ts_rate);
+
+ /* Round to the nearest ICE_RL_PROF_MULTIPLIER */
+ mv = round_up_64bit(mv_tmp, ICE_RL_PROF_MULTIPLIER);
+
+ /* First multiplier value greater than the given
+ * accuracy bytes
+ */
+ if (mv > ICE_RL_PROF_ACCURACY_BYTES) {
+ encode = i;
+ found = true;
+ break;
+ }
+ }
+ if (found) {
+ u16 wm;
+
+ wm = ice_sched_calc_wakeup(bw);
+ profile->rl_multiply = cpu_to_le16(mv);
+ profile->wake_up_calc = cpu_to_le16(wm);
+ profile->rl_encode = cpu_to_le16(encode);
+ status = 0;
+ } else {
+ status = ICE_ERR_DOES_NOT_EXIST;
+ }
+
+ return status;
+}
+
+/**
+ * ice_sched_add_rl_profile - add RL profile
+ * @pi: port information structure
+ * @rl_type: type of rate limit BW - min, max, or shared
+ * @bw: bandwidth in Kbps - Kilo bits per sec
+ * @layer_num: specifies in which layer to create profile
+ *
+ * This function first checks the existing list for corresponding BW
+ * parameter. If it exists, it returns the associated profile otherwise
+ * it creates a new rate limit profile for requested BW, and adds it to
+ * the HW DB and local list. It returns the new profile or null on error.
+ * The caller needs to hold the scheduler lock.
+ */
+static struct ice_aqc_rl_profile_info *
+ice_sched_add_rl_profile(struct ice_port_info *pi,
+ enum ice_rl_type rl_type, u32 bw, u8 layer_num)
+{
+ struct ice_aqc_rl_profile_generic_elem *buf;
+ struct ice_aqc_rl_profile_info *rl_prof_elem;
+ u16 profiles_added = 0, num_profiles = 1;
+ enum ice_status status;
+ struct ice_hw *hw;
+ u8 profile_type;
+
+ if (layer_num >= ICE_AQC_TOPO_MAX_LEVEL_NUM)
+ return NULL;
+ switch (rl_type) {
+ case ICE_MIN_BW:
+ profile_type = ICE_AQC_RL_PROFILE_TYPE_CIR;
+ break;
+ case ICE_MAX_BW:
+ profile_type = ICE_AQC_RL_PROFILE_TYPE_EIR;
+ break;
+ case ICE_SHARED_BW:
+ profile_type = ICE_AQC_RL_PROFILE_TYPE_SRL;
+ break;
+ default:
+ return NULL;
+ }
+
+ if (!pi)
+ return NULL;
+ hw = pi->hw;
+ list_for_each_entry(rl_prof_elem, &pi->rl_prof_list[layer_num],
+ list_entry)
+ if (rl_prof_elem->profile.flags == profile_type &&
+ rl_prof_elem->bw == bw)
+ /* Return existing profile ID info */
+ return rl_prof_elem;
+
+ /* Create new profile ID */
+ rl_prof_elem = devm_kzalloc(ice_hw_to_dev(hw), sizeof(*rl_prof_elem),
+ GFP_KERNEL);
+
+ if (!rl_prof_elem)
+ return NULL;
+
+ status = ice_sched_bw_to_rl_profile(bw, &rl_prof_elem->profile);
+ if (status)
+ goto exit_add_rl_prof;
+
+ rl_prof_elem->bw = bw;
+ /* layer_num is zero relative, and fw expects level from 1 to 9 */
+ rl_prof_elem->profile.level = layer_num + 1;
+ rl_prof_elem->profile.flags = profile_type;
+ rl_prof_elem->profile.max_burst_size = cpu_to_le16(hw->max_burst_size);
+
+ /* Create new entry in HW DB */
+ buf = (struct ice_aqc_rl_profile_generic_elem *)
+ &rl_prof_elem->profile;
+ status = ice_aq_add_rl_profile(hw, num_profiles, buf, sizeof(*buf),
+ &profiles_added, NULL);
+ if (status || profiles_added != num_profiles)
+ goto exit_add_rl_prof;
+
+ /* Good entry - add in the list */
+ rl_prof_elem->prof_id_ref = 0;
+ list_add(&rl_prof_elem->list_entry, &pi->rl_prof_list[layer_num]);
+ return rl_prof_elem;
+
+exit_add_rl_prof:
+ devm_kfree(ice_hw_to_dev(hw), rl_prof_elem);
+ return NULL;
+}
+
+/**
+ * ice_sched_cfg_node_bw_lmt - configure node sched params
+ * @hw: pointer to the HW struct
+ * @node: sched node to configure
+ * @rl_type: rate limit type CIR, EIR, or shared
+ * @rl_prof_id: rate limit profile ID
+ *
+ * This function configures node element's BW limit.
+ */
+static enum ice_status
+ice_sched_cfg_node_bw_lmt(struct ice_hw *hw, struct ice_sched_node *node,
+ enum ice_rl_type rl_type, u16 rl_prof_id)
+{
+ struct ice_aqc_txsched_elem_data buf;
+ struct ice_aqc_txsched_elem *data;
+
+ buf = node->info;
+ data = &buf.data;
+ switch (rl_type) {
+ case ICE_MIN_BW:
+ data->valid_sections |= ICE_AQC_ELEM_VALID_CIR;
+ data->cir_bw.bw_profile_idx = cpu_to_le16(rl_prof_id);
+ break;
+ case ICE_MAX_BW:
+ /* EIR BW and Shared BW profiles are mutually exclusive and
+ * hence only one of them may be set for any given element
+ */
+ if (data->valid_sections & ICE_AQC_ELEM_VALID_SHARED)
+ return ICE_ERR_CFG;
+ data->valid_sections |= ICE_AQC_ELEM_VALID_EIR;
+ data->eir_bw.bw_profile_idx = cpu_to_le16(rl_prof_id);
+ break;
+ case ICE_SHARED_BW:
+ /* Check for removing shared BW */
+ if (rl_prof_id == ICE_SCHED_NO_SHARED_RL_PROF_ID) {
+ /* remove shared profile */
+ data->valid_sections &= ~ICE_AQC_ELEM_VALID_SHARED;
+ data->srl_id = 0; /* clear SRL field */
+
+ /* enable back EIR to default profile */
+ data->valid_sections |= ICE_AQC_ELEM_VALID_EIR;
+ data->eir_bw.bw_profile_idx =
+ cpu_to_le16(ICE_SCHED_DFLT_RL_PROF_ID);
+ break;
+ }
+ /* EIR BW and Shared BW profiles are mutually exclusive and
+ * hence only one of them may be set for any given element
+ */
+ if ((data->valid_sections & ICE_AQC_ELEM_VALID_EIR) &&
+ (le16_to_cpu(data->eir_bw.bw_profile_idx) !=
+ ICE_SCHED_DFLT_RL_PROF_ID))
+ return ICE_ERR_CFG;
+ /* EIR BW is set to default, disable it */
+ data->valid_sections &= ~ICE_AQC_ELEM_VALID_EIR;
+ /* Okay to enable shared BW now */
+ data->valid_sections |= ICE_AQC_ELEM_VALID_SHARED;
+ data->srl_id = cpu_to_le16(rl_prof_id);
+ break;
+ default:
+ /* Unknown rate limit type */
+ return ICE_ERR_PARAM;
+ }
+
+ /* Configure element */
+ return ice_sched_update_elem(hw, node, &buf);
+}
+
+/**
+ * ice_sched_get_node_rl_prof_id - get node's rate limit profile ID
+ * @node: sched node
+ * @rl_type: rate limit type
+ *
+ * If existing profile matches, it returns the corresponding rate
+ * limit profile ID, otherwise it returns an invalid ID as error.
+ */
+static u16
+ice_sched_get_node_rl_prof_id(struct ice_sched_node *node,
+ enum ice_rl_type rl_type)
+{
+ u16 rl_prof_id = ICE_SCHED_INVAL_PROF_ID;
+ struct ice_aqc_txsched_elem *data;
+
+ data = &node->info.data;
+ switch (rl_type) {
+ case ICE_MIN_BW:
+ if (data->valid_sections & ICE_AQC_ELEM_VALID_CIR)
+ rl_prof_id = le16_to_cpu(data->cir_bw.bw_profile_idx);
+ break;
+ case ICE_MAX_BW:
+ if (data->valid_sections & ICE_AQC_ELEM_VALID_EIR)
+ rl_prof_id = le16_to_cpu(data->eir_bw.bw_profile_idx);
+ break;
+ case ICE_SHARED_BW:
+ if (data->valid_sections & ICE_AQC_ELEM_VALID_SHARED)
+ rl_prof_id = le16_to_cpu(data->srl_id);
+ break;
+ default:
+ break;
+ }
+
+ return rl_prof_id;
+}
+
+/**
+ * ice_sched_get_rl_prof_layer - selects rate limit profile creation layer
+ * @pi: port information structure
+ * @rl_type: type of rate limit BW - min, max, or shared
+ * @layer_index: layer index
+ *
+ * This function returns requested profile creation layer.
+ */
+static u8
+ice_sched_get_rl_prof_layer(struct ice_port_info *pi, enum ice_rl_type rl_type,
+ u8 layer_index)
+{
+ struct ice_hw *hw = pi->hw;
+
+ if (layer_index >= hw->num_tx_sched_layers)
+ return ICE_SCHED_INVAL_LAYER_NUM;
+ switch (rl_type) {
+ case ICE_MIN_BW:
+ if (hw->layer_info[layer_index].max_cir_rl_profiles)
+ return layer_index;
+ break;
+ case ICE_MAX_BW:
+ if (hw->layer_info[layer_index].max_eir_rl_profiles)
+ return layer_index;
+ break;
+ case ICE_SHARED_BW:
+ /* if current layer doesn't support SRL profile creation
+ * then try a layer up or down.
+ */
+ if (hw->layer_info[layer_index].max_srl_profiles)
+ return layer_index;
+ else if (layer_index < hw->num_tx_sched_layers - 1 &&
+ hw->layer_info[layer_index + 1].max_srl_profiles)
+ return layer_index + 1;
+ else if (layer_index > 0 &&
+ hw->layer_info[layer_index - 1].max_srl_profiles)
+ return layer_index - 1;
+ break;
+ default:
+ break;
+ }
+ return ICE_SCHED_INVAL_LAYER_NUM;
+}
+
+/**
+ * ice_sched_get_srl_node - get shared rate limit node
+ * @node: tree node
+ * @srl_layer: shared rate limit layer
+ *
+ * This function returns SRL node to be used for shared rate limit purpose.
+ * The caller needs to hold scheduler lock.
+ */
+static struct ice_sched_node *
+ice_sched_get_srl_node(struct ice_sched_node *node, u8 srl_layer)
+{
+ if (srl_layer > node->tx_sched_layer)
+ return node->children[0];
+ else if (srl_layer < node->tx_sched_layer)
+ /* Node can't be created without a parent. It will always
+ * have a valid parent except root node.
+ */
+ return node->parent;
+ else
+ return node;
+}
+
+/**
+ * ice_sched_rm_rl_profile - remove RL profile ID
+ * @pi: port information structure
+ * @layer_num: layer number where profiles are saved
+ * @profile_type: profile type like EIR, CIR, or SRL
+ * @profile_id: profile ID to remove
+ *
+ * This function removes rate limit profile from layer 'layer_num' of type
+ * 'profile_type' and profile ID as 'profile_id'. The caller needs to hold
+ * scheduler lock.
+ */
+static enum ice_status
+ice_sched_rm_rl_profile(struct ice_port_info *pi, u8 layer_num, u8 profile_type,
+ u16 profile_id)
+{
+ struct ice_aqc_rl_profile_info *rl_prof_elem;
+ enum ice_status status = 0;
+
+ if (layer_num >= ICE_AQC_TOPO_MAX_LEVEL_NUM)
+ return ICE_ERR_PARAM;
+ /* Check the existing list for RL profile */
+ list_for_each_entry(rl_prof_elem, &pi->rl_prof_list[layer_num],
+ list_entry)
+ if (rl_prof_elem->profile.flags == profile_type &&
+ le16_to_cpu(rl_prof_elem->profile.profile_id) ==
+ profile_id) {
+ if (rl_prof_elem->prof_id_ref)
+ rl_prof_elem->prof_id_ref--;
+
+ /* Remove old profile ID from database */
+ status = ice_sched_del_rl_profile(pi->hw, rl_prof_elem);
+ if (status && status != ICE_ERR_IN_USE)
+ ice_debug(pi->hw, ICE_DBG_SCHED,
+ "Remove rl profile failed\n");
+ break;
+ }
+ if (status == ICE_ERR_IN_USE)
+ status = 0;
+ return status;
+}
+
+/**
+ * ice_sched_set_node_bw_dflt - set node's bandwidth limit to default
+ * @pi: port information structure
+ * @node: pointer to node structure
+ * @rl_type: rate limit type min, max, or shared
+ * @layer_num: layer number where RL profiles are saved
+ *
+ * This function configures node element's BW rate limit profile ID of
+ * type CIR, EIR, or SRL to default. This function needs to be called
+ * with the scheduler lock held.
+ */
+static enum ice_status
+ice_sched_set_node_bw_dflt(struct ice_port_info *pi,
+ struct ice_sched_node *node,
+ enum ice_rl_type rl_type, u8 layer_num)
+{
+ enum ice_status status;
+ struct ice_hw *hw;
+ u8 profile_type;
+ u16 rl_prof_id;
+ u16 old_id;
+
+ hw = pi->hw;
+ switch (rl_type) {
+ case ICE_MIN_BW:
+ profile_type = ICE_AQC_RL_PROFILE_TYPE_CIR;
+ rl_prof_id = ICE_SCHED_DFLT_RL_PROF_ID;
+ break;
+ case ICE_MAX_BW:
+ profile_type = ICE_AQC_RL_PROFILE_TYPE_EIR;
+ rl_prof_id = ICE_SCHED_DFLT_RL_PROF_ID;
+ break;
+ case ICE_SHARED_BW:
+ profile_type = ICE_AQC_RL_PROFILE_TYPE_SRL;
+ /* No SRL is configured for default case */
+ rl_prof_id = ICE_SCHED_NO_SHARED_RL_PROF_ID;
+ break;
+ default:
+ return ICE_ERR_PARAM;
+ }
+ /* Save existing RL prof ID for later clean up */
+ old_id = ice_sched_get_node_rl_prof_id(node, rl_type);
+ /* Configure BW scheduling parameters */
+ status = ice_sched_cfg_node_bw_lmt(hw, node, rl_type, rl_prof_id);
+ if (status)
+ return status;
+
+ /* Remove stale RL profile ID */
+ if (old_id == ICE_SCHED_DFLT_RL_PROF_ID ||
+ old_id == ICE_SCHED_INVAL_PROF_ID)
+ return 0;
+
+ return ice_sched_rm_rl_profile(pi, layer_num, profile_type, old_id);
+}
+
+/**
+ * ice_sched_set_eir_srl_excl - set EIR/SRL exclusiveness
+ * @pi: port information structure
+ * @node: pointer to node structure
+ * @layer_num: layer number where rate limit profiles are saved
+ * @rl_type: rate limit type min, max, or shared
+ * @bw: bandwidth value
+ *
+ * This function prepares node element's bandwidth to SRL or EIR exclusively.
+ * EIR BW and Shared BW profiles are mutually exclusive and hence only one of
+ * them may be set for any given element. This function needs to be called
+ * with the scheduler lock held.
+ */
+static enum ice_status
+ice_sched_set_eir_srl_excl(struct ice_port_info *pi,
+ struct ice_sched_node *node,
+ u8 layer_num, enum ice_rl_type rl_type, u32 bw)
+{
+ if (rl_type == ICE_SHARED_BW) {
+ /* SRL node passed in this case, it may be different node */
+ if (bw == ICE_SCHED_DFLT_BW)
+ /* SRL being removed, ice_sched_cfg_node_bw_lmt()
+ * enables EIR to default. EIR is not set in this
+ * case, so no additional action is required.
+ */
+ return 0;
+
+ /* SRL being configured, set EIR to default here.
+ * ice_sched_cfg_node_bw_lmt() disables EIR when it
+ * configures SRL
+ */
+ return ice_sched_set_node_bw_dflt(pi, node, ICE_MAX_BW,
+ layer_num);
+ } else if (rl_type == ICE_MAX_BW &&
+ node->info.data.valid_sections & ICE_AQC_ELEM_VALID_SHARED) {
+ /* Remove Shared profile. Set default shared BW call
+ * removes shared profile for a node.
+ */
+ return ice_sched_set_node_bw_dflt(pi, node,
+ ICE_SHARED_BW,
+ layer_num);
+ }
+ return 0;
+}
+
+/**
+ * ice_sched_set_node_bw - set node's bandwidth
+ * @pi: port information structure
+ * @node: tree node
+ * @rl_type: rate limit type min, max, or shared
+ * @bw: bandwidth in Kbps - Kilo bits per sec
+ * @layer_num: layer number
+ *
+ * This function adds new profile corresponding to requested BW, configures
+ * node's RL profile ID of type CIR, EIR, or SRL, and removes old profile
+ * ID from local database. The caller needs to hold scheduler lock.
+ */
+static enum ice_status
+ice_sched_set_node_bw(struct ice_port_info *pi, struct ice_sched_node *node,
+ enum ice_rl_type rl_type, u32 bw, u8 layer_num)
+{
+ struct ice_aqc_rl_profile_info *rl_prof_info;
+ enum ice_status status = ICE_ERR_PARAM;
+ struct ice_hw *hw = pi->hw;
+ u16 old_id, rl_prof_id;
+
+ rl_prof_info = ice_sched_add_rl_profile(pi, rl_type, bw, layer_num);
+ if (!rl_prof_info)
+ return status;
+
+ rl_prof_id = le16_to_cpu(rl_prof_info->profile.profile_id);
+
+ /* Save existing RL prof ID for later clean up */
+ old_id = ice_sched_get_node_rl_prof_id(node, rl_type);
+ /* Configure BW scheduling parameters */
+ status = ice_sched_cfg_node_bw_lmt(hw, node, rl_type, rl_prof_id);
+ if (status)
+ return status;
+
+ /* New changes has been applied */
+ /* Increment the profile ID reference count */
+ rl_prof_info->prof_id_ref++;
+
+ /* Check for old ID removal */
+ if ((old_id == ICE_SCHED_DFLT_RL_PROF_ID && rl_type != ICE_SHARED_BW) ||
+ old_id == ICE_SCHED_INVAL_PROF_ID || old_id == rl_prof_id)
+ return 0;
+
+ return ice_sched_rm_rl_profile(pi, layer_num,
+ rl_prof_info->profile.flags,
+ old_id);
+}
+
+/**
+ * ice_sched_set_node_bw_lmt - set node's BW limit
+ * @pi: port information structure
+ * @node: tree node
+ * @rl_type: rate limit type min, max, or shared
+ * @bw: bandwidth in Kbps - Kilo bits per sec
+ *
+ * It updates node's BW limit parameters like BW RL profile ID of type CIR,
+ * EIR, or SRL. The caller needs to hold scheduler lock.
+ */
+static enum ice_status
+ice_sched_set_node_bw_lmt(struct ice_port_info *pi, struct ice_sched_node *node,
+ enum ice_rl_type rl_type, u32 bw)
+{
+ struct ice_sched_node *cfg_node = node;
+ enum ice_status status;
+
+ struct ice_hw *hw;
+ u8 layer_num;
+
+ if (!pi)
+ return ICE_ERR_PARAM;
+ hw = pi->hw;
+ /* Remove unused RL profile IDs from HW and SW DB */
+ ice_sched_rm_unused_rl_prof(pi);
+ layer_num = ice_sched_get_rl_prof_layer(pi, rl_type,
+ node->tx_sched_layer);
+ if (layer_num >= hw->num_tx_sched_layers)
+ return ICE_ERR_PARAM;
+
+ if (rl_type == ICE_SHARED_BW) {
+ /* SRL node may be different */
+ cfg_node = ice_sched_get_srl_node(node, layer_num);
+ if (!cfg_node)
+ return ICE_ERR_CFG;
+ }
+ /* EIR BW and Shared BW profiles are mutually exclusive and
+ * hence only one of them may be set for any given element
+ */
+ status = ice_sched_set_eir_srl_excl(pi, cfg_node, layer_num, rl_type,
+ bw);
+ if (status)
+ return status;
+ if (bw == ICE_SCHED_DFLT_BW)
+ return ice_sched_set_node_bw_dflt(pi, cfg_node, rl_type,
+ layer_num);
+ return ice_sched_set_node_bw(pi, cfg_node, rl_type, bw, layer_num);
+}
+
+/**
+ * ice_sched_set_node_bw_dflt_lmt - set node's BW limit to default
+ * @pi: port information structure
+ * @node: pointer to node structure
+ * @rl_type: rate limit type min, max, or shared
+ *
+ * This function configures node element's BW rate limit profile ID of
+ * type CIR, EIR, or SRL to default. This function needs to be called
+ * with the scheduler lock held.
+ */
+static enum ice_status
+ice_sched_set_node_bw_dflt_lmt(struct ice_port_info *pi,
+ struct ice_sched_node *node,
+ enum ice_rl_type rl_type)
+{
+ return ice_sched_set_node_bw_lmt(pi, node, rl_type,
+ ICE_SCHED_DFLT_BW);
+}
+
+/**
+ * ice_sched_validate_srl_node - Check node for SRL applicability
+ * @node: sched node to configure
+ * @sel_layer: selected SRL layer
+ *
+ * This function checks if the SRL can be applied to a selceted layer node on
+ * behalf of the requested node (first argument). This function needs to be
+ * called with scheduler lock held.
+ */
+static enum ice_status
+ice_sched_validate_srl_node(struct ice_sched_node *node, u8 sel_layer)
+{
+ /* SRL profiles are not available on all layers. Check if the
+ * SRL profile can be applied to a node above or below the
+ * requested node. SRL configuration is possible only if the
+ * selected layer's node has single child.
+ */
+ if (sel_layer == node->tx_sched_layer ||
+ ((sel_layer == node->tx_sched_layer + 1) &&
+ node->num_children == 1) ||
+ ((sel_layer == node->tx_sched_layer - 1) &&
+ (node->parent && node->parent->num_children == 1)))
+ return 0;
+
+ return ICE_ERR_CFG;
+}
+
+/**
+ * ice_sched_save_q_bw - save queue node's BW information
+ * @q_ctx: queue context structure
+ * @rl_type: rate limit type min, max, or shared
+ * @bw: bandwidth in Kbps - Kilo bits per sec
+ *
+ * Save BW information of queue type node for post replay use.
+ */
+static enum ice_status
+ice_sched_save_q_bw(struct ice_q_ctx *q_ctx, enum ice_rl_type rl_type, u32 bw)
+{
+ switch (rl_type) {
+ case ICE_MIN_BW:
+ ice_set_clear_cir_bw(&q_ctx->bw_t_info, bw);
+ break;
+ case ICE_MAX_BW:
+ ice_set_clear_eir_bw(&q_ctx->bw_t_info, bw);
+ break;
+ case ICE_SHARED_BW:
+ ice_set_clear_shared_bw(&q_ctx->bw_t_info, bw);
+ break;
+ default:
+ return ICE_ERR_PARAM;
+ }
+ return 0;
+}
+
+/**
+ * ice_sched_set_q_bw_lmt - sets queue BW limit
+ * @pi: port information structure
+ * @vsi_handle: sw VSI handle
+ * @tc: traffic class
+ * @q_handle: software queue handle
+ * @rl_type: min, max, or shared
+ * @bw: bandwidth in Kbps
+ *
+ * This function sets BW limit of queue scheduling node.
+ */
+static enum ice_status
+ice_sched_set_q_bw_lmt(struct ice_port_info *pi, u16 vsi_handle, u8 tc,
+ u16 q_handle, enum ice_rl_type rl_type, u32 bw)
+{
+ enum ice_status status = ICE_ERR_PARAM;
+ struct ice_sched_node *node;
+ struct ice_q_ctx *q_ctx;
+
+ if (!ice_is_vsi_valid(pi->hw, vsi_handle))
+ return ICE_ERR_PARAM;
+ mutex_lock(&pi->sched_lock);
+ q_ctx = ice_get_lan_q_ctx(pi->hw, vsi_handle, tc, q_handle);
+ if (!q_ctx)
+ goto exit_q_bw_lmt;
+ node = ice_sched_find_node_by_teid(pi->root, q_ctx->q_teid);
+ if (!node) {
+ ice_debug(pi->hw, ICE_DBG_SCHED, "Wrong q_teid\n");
+ goto exit_q_bw_lmt;
+ }
+
+ /* Return error if it is not a leaf node */
+ if (node->info.data.elem_type != ICE_AQC_ELEM_TYPE_LEAF)
+ goto exit_q_bw_lmt;
+
+ /* SRL bandwidth layer selection */
+ if (rl_type == ICE_SHARED_BW) {
+ u8 sel_layer; /* selected layer */
+
+ sel_layer = ice_sched_get_rl_prof_layer(pi, rl_type,
+ node->tx_sched_layer);
+ if (sel_layer >= pi->hw->num_tx_sched_layers) {
+ status = ICE_ERR_PARAM;
+ goto exit_q_bw_lmt;
+ }
+ status = ice_sched_validate_srl_node(node, sel_layer);
+ if (status)
+ goto exit_q_bw_lmt;
+ }
+
+ if (bw == ICE_SCHED_DFLT_BW)
+ status = ice_sched_set_node_bw_dflt_lmt(pi, node, rl_type);
+ else
+ status = ice_sched_set_node_bw_lmt(pi, node, rl_type, bw);
+
+ if (!status)
+ status = ice_sched_save_q_bw(q_ctx, rl_type, bw);
+
+exit_q_bw_lmt:
+ mutex_unlock(&pi->sched_lock);
+ return status;
+}
+
+/**
+ * ice_cfg_q_bw_lmt - configure queue BW limit
+ * @pi: port information structure
+ * @vsi_handle: sw VSI handle
+ * @tc: traffic class
+ * @q_handle: software queue handle
+ * @rl_type: min, max, or shared
+ * @bw: bandwidth in Kbps
+ *
+ * This function configures BW limit of queue scheduling node.
+ */
+enum ice_status
+ice_cfg_q_bw_lmt(struct ice_port_info *pi, u16 vsi_handle, u8 tc,
+ u16 q_handle, enum ice_rl_type rl_type, u32 bw)
+{
+ return ice_sched_set_q_bw_lmt(pi, vsi_handle, tc, q_handle, rl_type,
+ bw);
+}
+
+/**
+ * ice_cfg_q_bw_dflt_lmt - configure queue BW default limit
+ * @pi: port information structure
+ * @vsi_handle: sw VSI handle
+ * @tc: traffic class
+ * @q_handle: software queue handle
+ * @rl_type: min, max, or shared
+ *
+ * This function configures BW default limit of queue scheduling node.
+ */
+enum ice_status
+ice_cfg_q_bw_dflt_lmt(struct ice_port_info *pi, u16 vsi_handle, u8 tc,
+ u16 q_handle, enum ice_rl_type rl_type)
+{
+ return ice_sched_set_q_bw_lmt(pi, vsi_handle, tc, q_handle, rl_type,
+ ICE_SCHED_DFLT_BW);
+}
+
+/**
+ * ice_cfg_rl_burst_size - Set burst size value
+ * @hw: pointer to the HW struct
+ * @bytes: burst size in bytes
+ *
+ * This function configures/set the burst size to requested new value. The new
+ * burst size value is used for future rate limit calls. It doesn't change the
+ * existing or previously created RL profiles.
+ */
+enum ice_status ice_cfg_rl_burst_size(struct ice_hw *hw, u32 bytes)
+{
+ u16 burst_size_to_prog;
+
+ if (bytes < ICE_MIN_BURST_SIZE_ALLOWED ||
+ bytes > ICE_MAX_BURST_SIZE_ALLOWED)
+ return ICE_ERR_PARAM;
+ if (ice_round_to_num(bytes, 64) <=
+ ICE_MAX_BURST_SIZE_64_BYTE_GRANULARITY) {
+ /* 64 byte granularity case */
+ /* Disable MSB granularity bit */
+ burst_size_to_prog = ICE_64_BYTE_GRANULARITY;
+ /* round number to nearest 64 byte granularity */
+ bytes = ice_round_to_num(bytes, 64);
+ /* The value is in 64 byte chunks */
+ burst_size_to_prog |= (u16)(bytes / 64);
+ } else {
+ /* k bytes granularity case */
+ /* Enable MSB granularity bit */
+ burst_size_to_prog = ICE_KBYTE_GRANULARITY;
+ /* round number to nearest 1024 granularity */
+ bytes = ice_round_to_num(bytes, 1024);
+ /* check rounding doesn't go beyond allowed */
+ if (bytes > ICE_MAX_BURST_SIZE_KBYTE_GRANULARITY)
+ bytes = ICE_MAX_BURST_SIZE_KBYTE_GRANULARITY;
+ /* The value is in k bytes */
+ burst_size_to_prog |= (u16)(bytes / 1024);
+ }
+ hw->max_burst_size = burst_size_to_prog;
+ return 0;
+}
+
+/**
+ * ice_sched_replay_node_prio - re-configure node priority
+ * @hw: pointer to the HW struct
+ * @node: sched node to configure
+ * @priority: priority value
+ *
+ * This function configures node element's priority value. It
+ * needs to be called with scheduler lock held.
+ */
+static enum ice_status
+ice_sched_replay_node_prio(struct ice_hw *hw, struct ice_sched_node *node,
+ u8 priority)
+{
+ struct ice_aqc_txsched_elem_data buf;
+ struct ice_aqc_txsched_elem *data;
+ enum ice_status status;
+
+ buf = node->info;
+ data = &buf.data;
+ data->valid_sections |= ICE_AQC_ELEM_VALID_GENERIC;
+ data->generic = priority;
+
+ /* Configure element */
+ status = ice_sched_update_elem(hw, node, &buf);
+ return status;
+}
+
+/**
+ * ice_sched_replay_node_bw - replay node(s) BW
+ * @hw: pointer to the HW struct
+ * @node: sched node to configure
+ * @bw_t_info: BW type information
+ *
+ * This function restores node's BW from bw_t_info. The caller needs
+ * to hold the scheduler lock.
+ */
+static enum ice_status
+ice_sched_replay_node_bw(struct ice_hw *hw, struct ice_sched_node *node,
+ struct ice_bw_type_info *bw_t_info)
+{
+ struct ice_port_info *pi = hw->port_info;
+ enum ice_status status = ICE_ERR_PARAM;
+ u16 bw_alloc;
+
+ if (!node)
+ return status;
+ if (bitmap_empty(bw_t_info->bw_t_bitmap, ICE_BW_TYPE_CNT))
+ return 0;
+ if (test_bit(ICE_BW_TYPE_PRIO, bw_t_info->bw_t_bitmap)) {
+ status = ice_sched_replay_node_prio(hw, node,
+ bw_t_info->generic);
+ if (status)
+ return status;
+ }
+ if (test_bit(ICE_BW_TYPE_CIR, bw_t_info->bw_t_bitmap)) {
+ status = ice_sched_set_node_bw_lmt(pi, node, ICE_MIN_BW,
+ bw_t_info->cir_bw.bw);
+ if (status)
+ return status;
+ }
+ if (test_bit(ICE_BW_TYPE_CIR_WT, bw_t_info->bw_t_bitmap)) {
+ bw_alloc = bw_t_info->cir_bw.bw_alloc;
+ status = ice_sched_cfg_node_bw_alloc(hw, node, ICE_MIN_BW,
+ bw_alloc);
+ if (status)
+ return status;
+ }
+ if (test_bit(ICE_BW_TYPE_EIR, bw_t_info->bw_t_bitmap)) {
+ status = ice_sched_set_node_bw_lmt(pi, node, ICE_MAX_BW,
+ bw_t_info->eir_bw.bw);
+ if (status)
+ return status;
+ }
+ if (test_bit(ICE_BW_TYPE_EIR_WT, bw_t_info->bw_t_bitmap)) {
+ bw_alloc = bw_t_info->eir_bw.bw_alloc;
+ status = ice_sched_cfg_node_bw_alloc(hw, node, ICE_MAX_BW,
+ bw_alloc);
+ if (status)
+ return status;
+ }
+ if (test_bit(ICE_BW_TYPE_SHARED, bw_t_info->bw_t_bitmap))
+ status = ice_sched_set_node_bw_lmt(pi, node, ICE_SHARED_BW,
+ bw_t_info->shared_bw);
+ return status;
+}
+
+/**
+ * ice_sched_replay_q_bw - replay queue type node BW
+ * @pi: port information structure
+ * @q_ctx: queue context structure
+ *
+ * This function replays queue type node bandwidth. This function needs to be
+ * called with scheduler lock held.
+ */
+enum ice_status
+ice_sched_replay_q_bw(struct ice_port_info *pi, struct ice_q_ctx *q_ctx)
+{
+ struct ice_sched_node *q_node;
+
+ /* Following also checks the presence of node in tree */
+ q_node = ice_sched_find_node_by_teid(pi->root, q_ctx->q_teid);
+ if (!q_node)
+ return ICE_ERR_PARAM;
+ return ice_sched_replay_node_bw(pi->hw, q_node, &q_ctx->bw_t_info);
+}
diff --git a/drivers/net/ethernet/intel/ice/ice_sched.h b/drivers/net/ethernet/intel/ice/ice_sched.h
index 3902a8ad3025..f0593cfb6521 100644
--- a/drivers/net/ethernet/intel/ice/ice_sched.h
+++ b/drivers/net/ethernet/intel/ice/ice_sched.h
@@ -8,6 +8,36 @@
#define ICE_QGRP_LAYER_OFFSET 2
#define ICE_VSI_LAYER_OFFSET 4
+#define ICE_SCHED_INVAL_LAYER_NUM 0xFF
+/* Burst size is a 12 bits register that is configured while creating the RL
+ * profile(s). MSB is a granularity bit and tells the granularity type
+ * 0 - LSB bits are in 64 bytes granularity
+ * 1 - LSB bits are in 1K bytes granularity
+ */
+#define ICE_64_BYTE_GRANULARITY 0
+#define ICE_KBYTE_GRANULARITY BIT(11)
+#define ICE_MIN_BURST_SIZE_ALLOWED 64 /* In Bytes */
+#define ICE_MAX_BURST_SIZE_ALLOWED \
+ ((BIT(11) - 1) * 1024) /* In Bytes */
+#define ICE_MAX_BURST_SIZE_64_BYTE_GRANULARITY \
+ ((BIT(11) - 1) * 64) /* In Bytes */
+#define ICE_MAX_BURST_SIZE_KBYTE_GRANULARITY ICE_MAX_BURST_SIZE_ALLOWED
+
+#define ICE_RL_PROF_FREQUENCY 446000000
+#define ICE_RL_PROF_ACCURACY_BYTES 128
+#define ICE_RL_PROF_MULTIPLIER 10000
+#define ICE_RL_PROF_TS_MULTIPLIER 32
+#define ICE_RL_PROF_FRACTION 512
+
+/* BW rate limit profile parameters list entry along
+ * with bandwidth maintained per layer in port info
+ */
+struct ice_aqc_rl_profile_info {
+ struct ice_aqc_rl_profile_elem profile;
+ struct list_head list_entry;
+ u32 bw; /* requested */
+ u16 prof_id_ref; /* profile ID to node association ref count */
+};
struct ice_sched_agg_vsi_info {
struct list_head list_entry;
@@ -48,4 +78,13 @@ enum ice_status
ice_sched_cfg_vsi(struct ice_port_info *pi, u16 vsi_handle, u8 tc, u16 maxqs,
u8 owner, bool enable);
enum ice_status ice_rm_vsi_lan_cfg(struct ice_port_info *pi, u16 vsi_handle);
+enum ice_status
+ice_cfg_q_bw_lmt(struct ice_port_info *pi, u16 vsi_handle, u8 tc,
+ u16 q_handle, enum ice_rl_type rl_type, u32 bw);
+enum ice_status
+ice_cfg_q_bw_dflt_lmt(struct ice_port_info *pi, u16 vsi_handle, u8 tc,
+ u16 q_handle, enum ice_rl_type rl_type);
+enum ice_status ice_cfg_rl_burst_size(struct ice_hw *hw, u32 bytes);
+enum ice_status
+ice_sched_replay_q_bw(struct ice_port_info *pi, struct ice_q_ctx *q_ctx);
#endif /* _ICE_SCHED_H_ */
diff --git a/drivers/net/ethernet/intel/ice/ice_switch.h b/drivers/net/ethernet/intel/ice/ice_switch.h
index cb123fbe30be..fa14b9545dab 100644
--- a/drivers/net/ethernet/intel/ice/ice_switch.h
+++ b/drivers/net/ethernet/intel/ice/ice_switch.h
@@ -14,11 +14,6 @@
#define ICE_VSI_INVAL_ID 0xffff
#define ICE_INVAL_Q_HANDLE 0xFFFF
-/* VSI queue context structure */
-struct ice_q_ctx {
- u16 q_handle;
-};
-
/* VSI context structure for add/get/update/free operations */
struct ice_vsi_ctx {
u16 vsi_num;
diff --git a/drivers/net/ethernet/intel/ice/ice_type.h b/drivers/net/ethernet/intel/ice/ice_type.h
index 08fe3e5e72d4..d3d7049c97f0 100644
--- a/drivers/net/ethernet/intel/ice/ice_type.h
+++ b/drivers/net/ethernet/intel/ice/ice_type.h
@@ -19,6 +19,17 @@ static inline bool ice_is_tc_ena(unsigned long bitmap, u8 tc)
return test_bit(tc, &bitmap);
}
+static inline u64 round_up_64bit(u64 a, u32 b)
+{
+ return div64_long(((a) + (b) / 2), (b));
+}
+
+static inline u32 ice_round_to_num(u32 N, u32 R)
+{
+ return ((((N) % (R)) < ((R) / 2)) ? (((N) / (R)) * (R)) :
+ ((((N) + (R) - 1) / (R)) * (R)));
+}
+
/* Driver always calls main vsi_handle first */
#define ICE_MAIN_VSI_HANDLE 0
@@ -272,10 +283,56 @@ enum ice_agg_type {
ICE_AGG_TYPE_QG
};
+/* Rate limit types */
+enum ice_rl_type {
+ ICE_UNKNOWN_BW = 0,
+ ICE_MIN_BW, /* for CIR profile */
+ ICE_MAX_BW, /* for EIR profile */
+ ICE_SHARED_BW /* for shared profile */
+};
+
+#define ICE_SCHED_MIN_BW 500 /* in Kbps */
+#define ICE_SCHED_MAX_BW 100000000 /* in Kbps */
+#define ICE_SCHED_DFLT_BW 0xFFFFFFFF /* unlimited */
#define ICE_SCHED_DFLT_RL_PROF_ID 0
+#define ICE_SCHED_NO_SHARED_RL_PROF_ID 0xFFFF
#define ICE_SCHED_DFLT_BW_WT 1
+#define ICE_SCHED_INVAL_PROF_ID 0xFFFF
+#define ICE_SCHED_DFLT_BURST_SIZE (15 * 1024) /* in bytes (15k) */
-/* VSI type list entry to locate corresponding VSI/ag nodes */
+ /* Data structure for saving BW information */
+enum ice_bw_type {
+ ICE_BW_TYPE_PRIO,
+ ICE_BW_TYPE_CIR,
+ ICE_BW_TYPE_CIR_WT,
+ ICE_BW_TYPE_EIR,
+ ICE_BW_TYPE_EIR_WT,
+ ICE_BW_TYPE_SHARED,
+ ICE_BW_TYPE_CNT /* This must be last */
+};
+
+struct ice_bw {
+ u32 bw;
+ u16 bw_alloc;
+};
+
+struct ice_bw_type_info {
+ DECLARE_BITMAP(bw_t_bitmap, ICE_BW_TYPE_CNT);
+ u8 generic;
+ struct ice_bw cir_bw;
+ struct ice_bw eir_bw;
+ u32 shared_bw;
+};
+
+/* VSI queue context structure for given TC */
+struct ice_q_ctx {
+ u16 q_handle;
+ u32 q_teid;
+ /* bw_t_info saves queue BW information */
+ struct ice_bw_type_info bw_t_info;
+};
+
+/* VSI type list entry to locate corresponding VSI/aggregator nodes */
struct ice_sched_vsi_info {
struct ice_sched_node *vsi_node[ICE_MAX_TRAFFIC_CLASS];
struct ice_sched_node *ag_node[ICE_MAX_TRAFFIC_CLASS];
@@ -364,6 +421,8 @@ struct ice_port_info {
struct mutex sched_lock; /* protect access to TXSched tree */
struct ice_sched_node *
sib_head[ICE_MAX_TRAFFIC_CLASS][ICE_AQC_TOPO_MAX_LEVEL_NUM];
+ /* List contain profile ID(s) and other params per layer */
+ struct list_head rl_prof_list[ICE_AQC_TOPO_MAX_LEVEL_NUM];
struct ice_dcbx_cfg local_dcbx_cfg; /* Oper/Local Cfg */
/* DCBX info */
struct ice_dcbx_cfg remote_dcbx_cfg; /* Peer Cfg */
@@ -415,6 +474,8 @@ struct ice_hw {
u8 pf_id; /* device profile info */
+ u16 max_burst_size; /* driver sets this value */
+
/* Tx Scheduler values */
u16 num_tx_sched_layers;
u16 num_tx_sched_phys_layers;
--
2.20.1
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Intel-wired-lan] [PATCH S32 02/15] ice: Add NDO callback to set the maximum per-queue bitrate
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 02/15] ice: Add NDO callback to set the maximum per-queue bitrate Tony Nguyen
@ 2019-11-01 16:41 ` Bowers, AndrewX
0 siblings, 0 replies; 30+ messages in thread
From: Bowers, AndrewX @ 2019-11-01 16:41 UTC (permalink / raw)
To: intel-wired-lan
> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On
> Behalf Of Tony Nguyen
> Sent: Friday, October 25, 2019 7:34 AM
> To: intel-wired-lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [PATCH S32 02/15] ice: Add NDO callback to set the
> maximum per-queue bitrate
>
> From: Usha Ketineni <usha.k.ketineni@intel.com>
>
> Allow for rate limiting Tx queues. Bitrate is set in
> Mbps(megabits per second).
>
> Mbps max-rate is set for the queue via sysfs:
> /sys/class/net/<iface>/queues/tx-<queue>/tx_maxrate
> ex: echo 100 >/sys/class/net/ens7/queues/tx-0/tx_maxrate
> echo 200 >/sys/class/net/ens7/queues/tx-1/tx_maxrate
> Note: A value of zero for tx_maxrate means disabled,
> default is disabled.
>
> Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
> Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
> Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
> ---
> .../net/ethernet/intel/ice/ice_adminq_cmd.h | 46 +
> drivers/net/ethernet/intel/ice/ice_common.c | 10 +-
> drivers/net/ethernet/intel/ice/ice_common.h | 2 +
> drivers/net/ethernet/intel/ice/ice_dcb_lib.c | 10 +
> drivers/net/ethernet/intel/ice/ice_dcb_lib.h | 8 +
> drivers/net/ethernet/intel/ice/ice_main.c | 43 +
> drivers/net/ethernet/intel/ice/ice_sched.c | 1264 ++++++++++++++++-
> drivers/net/ethernet/intel/ice/ice_sched.h | 39 +
> drivers/net/ethernet/intel/ice/ice_switch.h | 5 -
> drivers/net/ethernet/intel/ice/ice_type.h | 63 +-
> 10 files changed, 1480 insertions(+), 10 deletions(-)
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
^ permalink raw reply [flat|nested] 30+ messages in thread
* [Intel-wired-lan] [PATCH S32 03/15] ice: Implement DCBNL support
2019-10-25 14:34 [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and ice_dis_vsi in DCB configuration flow Tony Nguyen
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 02/15] ice: Add NDO callback to set the maximum per-queue bitrate Tony Nguyen
@ 2019-10-25 14:34 ` Tony Nguyen
2019-11-01 16:41 ` Bowers, AndrewX
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 04/15] ice: avoid setting features during reset Tony Nguyen
` (12 subsequent siblings)
14 siblings, 1 reply; 30+ messages in thread
From: Tony Nguyen @ 2019-10-25 14:34 UTC (permalink / raw)
To: intel-wired-lan
From: Dave Ertman <david.m.ertman@intel.com>
Implement interface layer for the DCBNL subsystem. These are the functions
to support the callbacks defined in the dcbnl_rtnl_ops struct. These
callbacks are going to be used to interface with the DCB settings of the
device. Implementation of dcb_nl set functions and supporting SW DCB
functions.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
---
drivers/net/ethernet/intel/ice/Makefile | 2 +-
drivers/net/ethernet/intel/ice/ice.h | 2 +
drivers/net/ethernet/intel/ice/ice_dcb_lib.c | 15 +-
drivers/net/ethernet/intel/ice/ice_dcb_lib.h | 15 +-
drivers/net/ethernet/intel/ice/ice_dcb_nl.c | 933 ++++++++++++++++++
drivers/net/ethernet/intel/ice/ice_dcb_nl.h | 19 +
.../net/ethernet/intel/ice/ice_hw_autogen.h | 3 +
drivers/net/ethernet/intel/ice/ice_lib.c | 1 +
drivers/net/ethernet/intel/ice/ice_main.c | 6 +
9 files changed, 991 insertions(+), 5 deletions(-)
create mode 100644 drivers/net/ethernet/intel/ice/ice_dcb_nl.c
create mode 100644 drivers/net/ethernet/intel/ice/ice_dcb_nl.h
diff --git a/drivers/net/ethernet/intel/ice/Makefile b/drivers/net/ethernet/intel/ice/Makefile
index df5a9699276a..7cb829132d28 100644
--- a/drivers/net/ethernet/intel/ice/Makefile
+++ b/drivers/net/ethernet/intel/ice/Makefile
@@ -20,5 +20,5 @@ ice-y := ice_main.o \
ice_flex_pipe.o \
ice_ethtool.o
ice-$(CONFIG_PCI_IOV) += ice_virtchnl_pf.o ice_sriov.o
-ice-$(CONFIG_DCB) += ice_dcb.o ice_dcb_lib.o
+ice-$(CONFIG_DCB) += ice_dcb.o ice_dcb_nl.o ice_dcb_lib.o
ice-$(CONFIG_XDP_SOCKETS) += ice_xsk.o
diff --git a/drivers/net/ethernet/intel/ice/ice.h b/drivers/net/ethernet/intel/ice/ice.h
index 53a4870dd271..44466d4da057 100644
--- a/drivers/net/ethernet/intel/ice/ice.h
+++ b/drivers/net/ethernet/intel/ice/ice.h
@@ -180,6 +180,7 @@ enum ice_state {
__ICE_NEEDS_RESTART,
__ICE_PREPARED_FOR_RESET, /* set by driver when prepared */
__ICE_RESET_OICR_RECV, /* set by driver after rcv reset OICR */
+ __ICE_DCBNL_DEVRESET, /* set by dcbnl devreset */
__ICE_PFR_REQ, /* set by driver and peers */
__ICE_CORER_REQ, /* set by driver and peers */
__ICE_GLOBR_REQ, /* set by driver and peers */
@@ -367,6 +368,7 @@ struct ice_pf {
struct work_struct serv_task;
struct mutex avail_q_mutex; /* protects access to avail_[rx|tx]qs */
struct mutex sw_mutex; /* lock for protecting VSI alloc flow */
+ struct mutex tc_mutex; /* lock to protect TC changes */
u32 msg_enable;
u32 hw_csum_rx_error;
u32 oicr_idx; /* Other interrupt cause MSIX vector index */
diff --git a/drivers/net/ethernet/intel/ice/ice_dcb_lib.c b/drivers/net/ethernet/intel/ice/ice_dcb_lib.c
index 6e42e4b4c225..737c85349503 100644
--- a/drivers/net/ethernet/intel/ice/ice_dcb_lib.c
+++ b/drivers/net/ethernet/intel/ice/ice_dcb_lib.c
@@ -2,6 +2,7 @@
/* Copyright (c) 2019, Intel Corporation. */
#include "ice_dcb_lib.h"
+#include "ice_dcb_nl.h"
static void ice_pf_dcb_recfg(struct ice_pf *pf);
@@ -155,16 +156,19 @@ void ice_vsi_cfg_dcb_rings(struct ice_vsi *vsi)
* @new_cfg: DCBX config to apply
* @locked: is the RTNL held
*/
-static
int ice_pf_dcb_cfg(struct ice_pf *pf, struct ice_dcbx_cfg *new_cfg, bool locked)
{
- struct ice_dcbx_cfg *old_cfg, *curr_cfg;
struct ice_aqc_port_ets_elem buf = { 0 };
+ struct ice_dcbx_cfg *old_cfg, *curr_cfg;
+ int ret = ICE_DCB_NO_HW_CHG;
struct ice_vsi *pf_vsi;
- int ret = 0;
curr_cfg = &pf->hw.port_info->local_dcbx_cfg;
+ /* FW does not care if change happened */
+ if (!pf->hw.port_info->is_sw_lldp)
+ ret = ICE_DCB_HW_CHG_RST;
+
/* Enable DCB tagging only when more than one TC */
if (ice_dcb_get_num_tc(new_cfg) > 1) {
dev_dbg(&pf->pdev->dev, "DCB tagging enabled (num TC > 1)\n");
@@ -179,6 +183,7 @@ int ice_pf_dcb_cfg(struct ice_pf *pf, struct ice_dcbx_cfg *new_cfg, bool locked)
return ret;
}
+ dev_info(&pf->pdev->dev, "Commit DCB Configuration to the hardware\n");
/* Store old config in case FW config fails */
old_cfg = kzalloc(sizeof(*old_cfg), GFP_KERNEL);
memcpy(old_cfg, curr_cfg, sizeof(*old_cfg));
@@ -199,6 +204,7 @@ int ice_pf_dcb_cfg(struct ice_pf *pf, struct ice_dcbx_cfg *new_cfg, bool locked)
memcpy(curr_cfg, new_cfg, sizeof(*curr_cfg));
memcpy(&curr_cfg->etsrec, &curr_cfg->etscfg, sizeof(curr_cfg->etsrec));
+ memcpy(&new_cfg->etsrec, &curr_cfg->etscfg, sizeof(curr_cfg->etsrec));
/* Only send new config to HW if we are in SW LLDP mode. Otherwise,
* the new config came from the HW in the first place.
@@ -558,6 +564,8 @@ static void ice_pf_dcb_recfg(struct ice_pf *pf)
}
ice_vsi_map_rings_to_vectors(pf->vsi[v]);
+ if (pf->vsi[v]->type == ICE_VSI_PF)
+ ice_dcbnl_set_all(pf->vsi[v]);
}
}
@@ -769,6 +777,7 @@ ice_dcb_process_lldp_set_mib_change(struct ice_pf *pf,
need_reconfig = ice_dcb_need_recfg(pf, &tmp_dcbx_cfg,
&pi->local_dcbx_cfg);
+ ice_dcbnl_flush_apps(pf, &tmp_dcbx_cfg, &pi->local_dcbx_cfg);
if (!need_reconfig)
return;
diff --git a/drivers/net/ethernet/intel/ice/ice_dcb_lib.h b/drivers/net/ethernet/intel/ice/ice_dcb_lib.h
index 59e40cf2dd73..e90e25b7da77 100644
--- a/drivers/net/ethernet/intel/ice/ice_dcb_lib.h
+++ b/drivers/net/ethernet/intel/ice/ice_dcb_lib.h
@@ -9,12 +9,17 @@
#include "ice_lib.h"
#ifdef CONFIG_DCB
-#define ICE_TC_MAX_BW 100 /* Default Max BW percentage */
+#define ICE_TC_MAX_BW 100 /* Default Max BW percentage */
+#define ICE_DCB_HW_CHG_RST 0 /* DCB configuration changed with reset */
+#define ICE_DCB_NO_HW_CHG 1 /* DCB configuration did not change */
+#define ICE_DCB_HW_CHG 2 /* DCB configuration changed, no reset */
void ice_dcb_rebuild(struct ice_pf *pf);
u8 ice_dcb_get_ena_tc(struct ice_dcbx_cfg *dcbcfg);
u8 ice_dcb_get_num_tc(struct ice_dcbx_cfg *dcbcfg);
u8 ice_dcb_get_tc(struct ice_vsi *vsi, int queue_index);
+int
+ice_pf_dcb_cfg(struct ice_pf *pf, struct ice_dcbx_cfg *new_cfg, bool locked);
void ice_vsi_cfg_dcb_rings(struct ice_vsi *vsi);
int ice_init_pf_dcb(struct ice_pf *pf, bool locked);
void ice_update_dcb_stats(struct ice_pf *pf);
@@ -57,6 +62,14 @@ ice_init_pf_dcb(struct ice_pf *pf, bool __always_unused locked)
return -EOPNOTSUPP;
}
+static inline int
+ice_pf_dcb_cfg(struct ice_pf __always_unused *pf,
+ struct ice_dcbx_cfg __always_unused *new_cfg,
+ bool __always_unused locked)
+{
+ return -EOPNOTSUPP;
+}
+
static inline int
ice_tx_prepare_vlan_flags_dcb(struct ice_ring __always_unused *tx_ring,
struct ice_tx_buf __always_unused *first)
diff --git a/drivers/net/ethernet/intel/ice/ice_dcb_nl.c b/drivers/net/ethernet/intel/ice/ice_dcb_nl.c
new file mode 100644
index 000000000000..717efbb7c4d1
--- /dev/null
+++ b/drivers/net/ethernet/intel/ice/ice_dcb_nl.c
@@ -0,0 +1,933 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (c) 2019, Intel Corporation. */
+
+#include "ice.h"
+#include "ice_dcb.h"
+#include "ice_dcb_lib.h"
+#include "ice_dcb_nl.h"
+#include <net/dcbnl.h>
+
+#define ICE_APP_PROT_ID_ROCE 0x8915
+
+/**
+ * ice_dcbnl_devreset - perform enough of a ifdown/ifup to sync DCBNL info
+ * @netdev: device associated with interface that needs reset
+ */
+static void ice_dcbnl_devreset(struct net_device *netdev)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+
+ while (ice_is_reset_in_progress(pf->state))
+ usleep_range(1000, 2000);
+
+ set_bit(__ICE_DCBNL_DEVRESET, pf->state);
+ dev_close(netdev);
+ netdev_state_change(netdev);
+ dev_open(netdev, NULL);
+ netdev_state_change(netdev);
+ clear_bit(__ICE_DCBNL_DEVRESET, pf->state);
+}
+
+/**
+ * ice_dcbnl_getets - retrieve local ETS configuration
+ * @netdev: the relevant netdev
+ * @ets: struct to hold ETS configuration
+ */
+static int ice_dcbnl_getets(struct net_device *netdev, struct ieee_ets *ets)
+{
+ struct ice_dcbx_cfg *dcbxcfg;
+ struct ice_port_info *pi;
+ struct ice_pf *pf;
+
+ pf = ice_netdev_to_pf(netdev);
+ pi = pf->hw.port_info;
+ dcbxcfg = &pi->local_dcbx_cfg;
+
+ ets->willing = dcbxcfg->etscfg.willing;
+ ets->ets_cap = dcbxcfg->etscfg.maxtcs;
+ ets->cbs = dcbxcfg->etscfg.cbs;
+ memcpy(ets->tc_tx_bw, dcbxcfg->etscfg.tcbwtable, sizeof(ets->tc_tx_bw));
+ memcpy(ets->tc_rx_bw, dcbxcfg->etscfg.tcbwtable, sizeof(ets->tc_rx_bw));
+ memcpy(ets->tc_tsa, dcbxcfg->etscfg.tsatable, sizeof(ets->tc_tsa));
+ memcpy(ets->prio_tc, dcbxcfg->etscfg.prio_table, sizeof(ets->prio_tc));
+ memcpy(ets->tc_reco_bw, dcbxcfg->etsrec.tcbwtable,
+ sizeof(ets->tc_reco_bw));
+ memcpy(ets->tc_reco_tsa, dcbxcfg->etsrec.tsatable,
+ sizeof(ets->tc_reco_tsa));
+ memcpy(ets->reco_prio_tc, dcbxcfg->etscfg.prio_table,
+ sizeof(ets->reco_prio_tc));
+
+ return 0;
+}
+
+/**
+ * ice_dcbnl_setets - set IEEE ETS configuration
+ * @netdev: pointer to relevant netdev
+ * @ets: struct to hold ETS configuration
+ */
+static int ice_dcbnl_setets(struct net_device *netdev, struct ieee_ets *ets)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+ struct ice_dcbx_cfg *new_cfg;
+ int bwcfg = 0, bwrec = 0;
+ int err, i, max_tc = 0;
+
+ if ((pf->dcbx_cap & DCB_CAP_DCBX_LLD_MANAGED) ||
+ !(pf->dcbx_cap & DCB_CAP_DCBX_VER_IEEE))
+ return -EINVAL;
+
+ new_cfg = &pf->hw.port_info->desired_dcbx_cfg;
+
+ mutex_lock(&pf->tc_mutex);
+
+ new_cfg->etscfg.willing = ets->willing;
+ new_cfg->etscfg.cbs = ets->cbs;
+ ice_for_each_traffic_class(i) {
+ new_cfg->etscfg.tcbwtable[i] = ets->tc_tx_bw[i];
+ bwcfg += ets->tc_tx_bw[i];
+ new_cfg->etscfg.tsatable[i] = ets->tc_tsa[i];
+ new_cfg->etscfg.prio_table[i] = ets->prio_tc[i];
+ if (ets->prio_tc[i] > max_tc)
+ max_tc = ets->prio_tc[i];
+ new_cfg->etsrec.tcbwtable[i] = ets->tc_reco_bw[i];
+ bwrec += ets->tc_reco_bw[i];
+ new_cfg->etsrec.tsatable[i] = ets->tc_reco_tsa[i];
+ new_cfg->etsrec.prio_table[i] = ets->reco_prio_tc[i];
+ }
+
+ /* max_tc is a 1-8 value count of number of TC's, not a 0-7 value
+ * for the TC's index number. Add one to value if not zero, and
+ * for zero set it to the FW's default value
+ */
+ if (max_tc)
+ max_tc++;
+ else
+ max_tc = IEEE_8021QAZ_MAX_TCS;
+
+ new_cfg->etscfg.maxtcs = max_tc;
+
+ if (!bwcfg)
+ new_cfg->etscfg.tcbwtable[0] = 100;
+
+ if (!bwrec)
+ new_cfg->etsrec.tcbwtable[0] = 100;
+
+ err = ice_pf_dcb_cfg(pf, new_cfg, true);
+ /* return of zero indicates new cfg applied */
+ if (err == ICE_DCB_HW_CHG_RST)
+ ice_dcbnl_devreset(netdev);
+ if (err == ICE_DCB_NO_HW_CHG)
+ err = ICE_DCB_HW_CHG_RST;
+
+ mutex_unlock(&pf->tc_mutex);
+ return err;
+}
+
+/**
+ * ice_dcbnl_getnumtcs - Get max number of traffic classes supported
+ * @dev: pointer to netdev struct
+ * @tcid: TC ID
+ * @num: total number of TCs supported by the adapter
+ *
+ * Return the total number of TCs supported
+ */
+static int
+ice_dcbnl_getnumtcs(struct net_device *dev, int __always_unused tcid, u8 *num)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(dev);
+
+ if (!test_bit(ICE_FLAG_DCB_CAPABLE, pf->flags))
+ return -EINVAL;
+
+ *num = IEEE_8021QAZ_MAX_TCS;
+ return 0;
+}
+
+/**
+ * ice_dcbnl_getdcbx - retrieve current DCBX capability
+ * @netdev: pointer to the netdev struct
+ */
+static u8 ice_dcbnl_getdcbx(struct net_device *netdev)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+
+ return pf->dcbx_cap;
+}
+
+/**
+ * ice_dcbnl_setdcbx - set required DCBX capability
+ * @netdev: the corresponding netdev
+ * @mode: required mode
+ */
+static u8 ice_dcbnl_setdcbx(struct net_device *netdev, u8 mode)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+
+ /* No support for LLD_MANAGED modes or CEE+IEEE */
+ if ((mode & DCB_CAP_DCBX_LLD_MANAGED) ||
+ ((mode & DCB_CAP_DCBX_VER_IEEE) && (mode & DCB_CAP_DCBX_VER_CEE)) ||
+ !(mode & DCB_CAP_DCBX_HOST))
+ return ICE_DCB_NO_HW_CHG;
+
+ /* Already set to the given mode no change */
+ if (mode == pf->dcbx_cap)
+ return ICE_DCB_NO_HW_CHG;
+
+ pf->dcbx_cap = mode;
+ if (mode & DCB_CAP_DCBX_VER_CEE)
+ pf->hw.port_info->local_dcbx_cfg.dcbx_mode = ICE_DCBX_MODE_CEE;
+ else
+ pf->hw.port_info->local_dcbx_cfg.dcbx_mode = ICE_DCBX_MODE_IEEE;
+
+ dev_info(&pf->pdev->dev, "DCBx mode = 0x%x\n", mode);
+ return ICE_DCB_HW_CHG_RST;
+}
+
+/**
+ * ice_dcbnl_get_perm_hw_addr - MAC address used by DCBX
+ * @netdev: pointer to netdev struct
+ * @perm_addr: buffer to return permanent MAC address
+ */
+static void ice_dcbnl_get_perm_hw_addr(struct net_device *netdev, u8 *perm_addr)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+ struct ice_port_info *pi = pf->hw.port_info;
+ int i, j;
+
+ memset(perm_addr, 0xff, MAX_ADDR_LEN);
+
+ for (i = 0; i < netdev->addr_len; i++)
+ perm_addr[i] = pi->mac.perm_addr[i];
+
+ for (j = 0; j < netdev->addr_len; j++, i++)
+ perm_addr[i] = pi->mac.perm_addr[j];
+}
+
+/**
+ * ice_get_pfc_delay - Retrieve PFC Link Delay
+ * @hw: pointer to HW struct
+ * @delay: holds the PFC Link Delay value
+ */
+static void ice_get_pfc_delay(struct ice_hw *hw, u16 *delay)
+{
+ u32 val;
+
+ val = rd32(hw, PRTDCB_GENC);
+ *delay = (u16)((val & PRTDCB_GENC_PFCLDA_M) >> PRTDCB_GENC_PFCLDA_S);
+}
+
+/**
+ * ice_dcbnl_getpfc - retrieve local IEEE PFC config
+ * @netdev: pointer to netdev struct
+ * @pfc: struct to hold PFC info
+ */
+static int ice_dcbnl_getpfc(struct net_device *netdev, struct ieee_pfc *pfc)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+ struct ice_dcbx_cfg *dcbxcfg;
+ struct ice_port_info *pi = pf->hw.port_info;
+ int i;
+
+ dcbxcfg = &pi->local_dcbx_cfg;
+ pfc->pfc_cap = dcbxcfg->pfc.pfccap;
+ pfc->pfc_en = dcbxcfg->pfc.pfcena;
+ pfc->mbc = dcbxcfg->pfc.mbc;
+ ice_get_pfc_delay(&pf->hw, &pfc->delay);
+
+ ice_for_each_traffic_class(i) {
+ pfc->requests[i] = pf->stats.priority_xoff_tx[i];
+ pfc->indications[i] = pf->stats.priority_xoff_rx[i];
+ }
+
+ return 0;
+}
+
+/**
+ * ice_dcbnl_setpfc - set local IEEE PFC config
+ * @netdev: pointer to relevant netdev
+ * @pfc: pointer to struct holding PFC config
+ */
+static int ice_dcbnl_setpfc(struct net_device *netdev, struct ieee_pfc *pfc)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+ struct ice_dcbx_cfg *new_cfg;
+ int err;
+
+ if ((pf->dcbx_cap & DCB_CAP_DCBX_LLD_MANAGED) ||
+ !(pf->dcbx_cap & DCB_CAP_DCBX_VER_IEEE))
+ return -EINVAL;
+
+ mutex_lock(&pf->tc_mutex);
+
+ new_cfg = &pf->hw.port_info->desired_dcbx_cfg;
+
+ if (pfc->pfc_cap)
+ new_cfg->pfc.pfccap = pfc->pfc_cap;
+ else
+ new_cfg->pfc.pfccap = pf->hw.func_caps.common_cap.maxtc;
+
+ new_cfg->pfc.pfcena = pfc->pfc_en;
+
+ err = ice_pf_dcb_cfg(pf, new_cfg, true);
+ if (err == ICE_DCB_HW_CHG_RST)
+ ice_dcbnl_devreset(netdev);
+ if (err == ICE_DCB_NO_HW_CHG)
+ err = ICE_DCB_HW_CHG_RST;
+ mutex_unlock(&pf->tc_mutex);
+ return err;
+}
+
+/**
+ * ice_dcbnl_get_pfc_cfg - Get CEE PFC config
+ * @netdev: pointer to netdev struct
+ * @prio: corresponding user priority
+ * @setting: the PFC setting for given priority
+ */
+static void
+ice_dcbnl_get_pfc_cfg(struct net_device *netdev, int prio, u8 *setting)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+ struct ice_port_info *pi = pf->hw.port_info;
+
+ if ((pf->dcbx_cap & DCB_CAP_DCBX_LLD_MANAGED) ||
+ !(pf->dcbx_cap & DCB_CAP_DCBX_VER_CEE))
+ return;
+
+ if (prio >= ICE_MAX_USER_PRIORITY)
+ return;
+
+ *setting = (pi->local_dcbx_cfg.pfc.pfcena >> prio) & 0x1;
+ dev_dbg(&pf->pdev->dev,
+ "Get PFC Config up=%d, setting=%d, pfcenable=0x%x\n",
+ prio, *setting, pi->local_dcbx_cfg.pfc.pfcena);
+}
+
+/**
+ * ice_dcbnl_set_pfc_cfg - Set CEE PFC config
+ * @netdev: the corresponding netdev
+ * @prio: User Priority
+ * @set: PFC setting to apply
+ */
+static void ice_dcbnl_set_pfc_cfg(struct net_device *netdev, int prio, u8 set)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+ struct ice_dcbx_cfg *new_cfg;
+
+ if ((pf->dcbx_cap & DCB_CAP_DCBX_LLD_MANAGED) ||
+ !(pf->dcbx_cap & DCB_CAP_DCBX_VER_CEE))
+ return;
+
+ if (prio >= ICE_MAX_USER_PRIORITY)
+ return;
+
+ new_cfg = &pf->hw.port_info->desired_dcbx_cfg;
+
+ new_cfg->pfc.pfccap = pf->hw.func_caps.common_cap.maxtc;
+ if (set)
+ new_cfg->pfc.pfcena |= BIT(prio);
+ else
+ new_cfg->pfc.pfcena &= ~BIT(prio);
+
+ dev_dbg(&pf->pdev->dev, "Set PFC config UP:%d set:%d pfcena:0x%x\n",
+ prio, set, new_cfg->pfc.pfcena);
+}
+
+/**
+ * ice_dcbnl_getpfcstate - get CEE PFC mode
+ * @netdev: pointer to netdev struct
+ */
+static u8 ice_dcbnl_getpfcstate(struct net_device *netdev)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+ struct ice_port_info *pi = pf->hw.port_info;
+
+ /* Return enabled if any UP enabled for PFC */
+ if (pi->local_dcbx_cfg.pfc.pfcena)
+ return 1;
+
+ return 0;
+}
+
+/**
+ * ice_dcbnl_getstate - get DCB enabled state
+ * @netdev: pointer to netdev struct
+ */
+static u8 ice_dcbnl_getstate(struct net_device *netdev)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+ u8 state = 0;
+
+ state = test_bit(ICE_FLAG_DCB_CAPABLE, pf->flags);
+
+ dev_dbg(&pf->pdev->dev, "DCB enabled state = %d\n", state);
+ return state;
+}
+
+/**
+ * ice_dcbnl_setstate - Set CEE DCB state
+ * @netdev: pointer to relevant netdev
+ * @state: state value to set
+ */
+static u8 ice_dcbnl_setstate(struct net_device *netdev, u8 state)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+
+ if ((pf->dcbx_cap & DCB_CAP_DCBX_LLD_MANAGED) ||
+ !(pf->dcbx_cap & DCB_CAP_DCBX_VER_CEE))
+ return ICE_DCB_NO_HW_CHG;
+
+ /* Nothing to do */
+ if (!!state == test_bit(ICE_FLAG_DCB_ENA, pf->flags))
+ return ICE_DCB_NO_HW_CHG;
+
+ if (state) {
+ set_bit(ICE_FLAG_DCB_ENA, pf->flags);
+ memcpy(&pf->hw.port_info->desired_dcbx_cfg,
+ &pf->hw.port_info->local_dcbx_cfg,
+ sizeof(struct ice_dcbx_cfg));
+ } else {
+ clear_bit(ICE_FLAG_DCB_ENA, pf->flags);
+ }
+
+ return ICE_DCB_HW_CHG;
+}
+
+/**
+ * ice_dcbnl_get_pg_tc_cfg_tx - get CEE PG Tx config
+ * @netdev: pointer to netdev struct
+ * @prio: the corresponding user priority
+ * @prio_type: traffic priority type
+ * @pgid: the BW group ID the traffic class belongs to
+ * @bw_pct: BW percentage for the corresponding BWG
+ * @up_map: prio mapped to corresponding TC
+ */
+static void
+ice_dcbnl_get_pg_tc_cfg_tx(struct net_device *netdev, int prio,
+ u8 __always_unused *prio_type, u8 *pgid,
+ u8 __always_unused *bw_pct,
+ u8 __always_unused *up_map)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+ struct ice_port_info *pi = pf->hw.port_info;
+
+ if ((pf->dcbx_cap & DCB_CAP_DCBX_LLD_MANAGED) ||
+ !(pf->dcbx_cap & DCB_CAP_DCBX_VER_CEE))
+ return;
+
+ if (prio >= ICE_MAX_USER_PRIORITY)
+ return;
+
+ *pgid = pi->local_dcbx_cfg.etscfg.prio_table[prio];
+ dev_dbg(&pf->pdev->dev,
+ "Get PG config prio=%d tc=%d\n", prio, *pgid);
+}
+
+/**
+ * ice_dcbnl_set_pg_tc_cfg_tx - set CEE PG Tx config
+ * @netdev: pointer to relevant netdev
+ * @tc: the corresponding traffic class
+ * @prio_type: the traffic priority type
+ * @bwg_id: the BW group ID the TC belongs to
+ * @bw_pct: the BW perventage for the BWG
+ * @up_map: prio mapped to corresponding TC
+ */
+static void
+ice_dcbnl_set_pg_tc_cfg_tx(struct net_device *netdev, int tc,
+ u8 __always_unused prio_type,
+ u8 __always_unused bwg_id,
+ u8 __always_unused bw_pct, u8 up_map)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+ struct ice_dcbx_cfg *new_cfg;
+ int i;
+
+ if ((pf->dcbx_cap & DCB_CAP_DCBX_LLD_MANAGED) ||
+ !(pf->dcbx_cap & DCB_CAP_DCBX_VER_CEE))
+ return;
+
+ if (tc >= ICE_MAX_TRAFFIC_CLASS)
+ return;
+
+ new_cfg = &pf->hw.port_info->desired_dcbx_cfg;
+
+ /* prio_type, bwg_id and bw_pct per UP are not supported */
+
+ ice_for_each_traffic_class(i) {
+ if (up_map & BIT(i))
+ new_cfg->etscfg.prio_table[i] = tc;
+ }
+ new_cfg->etscfg.tsatable[tc] = ICE_IEEE_TSA_ETS;
+}
+
+/**
+ * ice_dcbnl_get_pg_bwg_cfg_tx - Get CEE PGBW config
+ * @netdev: pointer to the netdev struct
+ * @pgid: corresponding traffic class
+ * @bw_pct: the BW percentage for the corresponding TC
+ */
+static void
+ice_dcbnl_get_pg_bwg_cfg_tx(struct net_device *netdev, int pgid, u8 *bw_pct)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+ struct ice_port_info *pi = pf->hw.port_info;
+
+ if ((pf->dcbx_cap & DCB_CAP_DCBX_LLD_MANAGED) ||
+ !(pf->dcbx_cap & DCB_CAP_DCBX_VER_CEE))
+ return;
+
+ if (pgid >= ICE_MAX_TRAFFIC_CLASS)
+ return;
+
+ *bw_pct = pi->local_dcbx_cfg.etscfg.tcbwtable[pgid];
+ dev_dbg(&pf->pdev->dev, "Get PG BW config tc=%d bw_pct=%d\n",
+ pgid, *bw_pct);
+}
+
+/**
+ * ice_dcbnl_set_pg_bwg_cfg_tx - set CEE PG Tx BW config
+ * @netdev: the corresponding netdev
+ * @pgid: Correspongind traffic class
+ * @bw_pct: the BW percentage for the specified TC
+ */
+static void
+ice_dcbnl_set_pg_bwg_cfg_tx(struct net_device *netdev, int pgid, u8 bw_pct)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+ struct ice_dcbx_cfg *new_cfg;
+
+ if ((pf->dcbx_cap & DCB_CAP_DCBX_LLD_MANAGED) ||
+ !(pf->dcbx_cap & DCB_CAP_DCBX_VER_CEE))
+ return;
+
+ if (pgid >= ICE_MAX_TRAFFIC_CLASS)
+ return;
+
+ new_cfg = &pf->hw.port_info->desired_dcbx_cfg;
+
+ new_cfg->etscfg.tcbwtable[pgid] = bw_pct;
+}
+
+/**
+ * ice_dcbnl_get_pg_tc_cfg_rx - Get CEE PG Rx config
+ * @netdev: pointer to netdev struct
+ * @prio: the corresponding user priority
+ * @prio_type: the traffic priority type
+ * @pgid: the PG ID
+ * @bw_pct: the BW percentage for the corresponding BWG
+ * @up_map: prio mapped to corresponding TC
+ */
+static void
+ice_dcbnl_get_pg_tc_cfg_rx(struct net_device *netdev, int prio,
+ u8 __always_unused *prio_type, u8 *pgid,
+ u8 __always_unused *bw_pct,
+ u8 __always_unused *up_map)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+ struct ice_port_info *pi = pf->hw.port_info;
+
+ if ((pf->dcbx_cap & DCB_CAP_DCBX_LLD_MANAGED) ||
+ !(pf->dcbx_cap & DCB_CAP_DCBX_VER_CEE))
+ return;
+
+ if (prio >= ICE_MAX_USER_PRIORITY)
+ return;
+
+ *pgid = pi->local_dcbx_cfg.etscfg.prio_table[prio];
+}
+
+/**
+ * ice_dcbnl_get_pg_bwg_cfg_rx - Get CEE PG BW Rx config
+ * @netdev: pointer to netdev struct
+ * @pgid: the corresponding traffic class
+ * @bw_pct: the BW percentage for the corresponding TC
+ */
+static void
+ice_dcbnl_get_pg_bwg_cfg_rx(struct net_device *netdev, int __always_unused pgid,
+ u8 *bw_pct)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+
+ if ((pf->dcbx_cap & DCB_CAP_DCBX_LLD_MANAGED) ||
+ !(pf->dcbx_cap & DCB_CAP_DCBX_VER_CEE))
+ return;
+
+ *bw_pct = 0;
+}
+
+/**
+ * ice_dcbnl_get_cap - Get DCBX capabilities of adapter
+ * @netdev: pointer to netdev struct
+ * @capid: the capability type
+ * @cap: the capability value
+ */
+static u8 ice_dcbnl_get_cap(struct net_device *netdev, int capid, u8 *cap)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+
+ if (!(test_bit(ICE_FLAG_DCB_CAPABLE, pf->flags)))
+ return ICE_DCB_NO_HW_CHG;
+
+ switch (capid) {
+ case DCB_CAP_ATTR_PG:
+ *cap = true;
+ break;
+ case DCB_CAP_ATTR_PFC:
+ *cap = true;
+ break;
+ case DCB_CAP_ATTR_UP2TC:
+ *cap = false;
+ break;
+ case DCB_CAP_ATTR_PG_TCS:
+ *cap = 0x80;
+ break;
+ case DCB_CAP_ATTR_PFC_TCS:
+ *cap = 0x80;
+ break;
+ case DCB_CAP_ATTR_GSP:
+ *cap = false;
+ break;
+ case DCB_CAP_ATTR_BCN:
+ *cap = false;
+ break;
+ case DCB_CAP_ATTR_DCBX:
+ *cap = pf->dcbx_cap;
+ break;
+ default:
+ *cap = false;
+ break;
+ }
+
+ dev_dbg(&pf->pdev->dev, "DCBX Get Capability cap=%d capval=0x%x\n",
+ capid, *cap);
+ return 0;
+}
+
+/**
+ * ice_dcbnl_getapp - get CEE APP
+ * @netdev: pointer to netdev struct
+ * @idtype: the App selector
+ * @id: the App ethtype or port number
+ */
+static int ice_dcbnl_getapp(struct net_device *netdev, u8 idtype, u16 id)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+ struct dcb_app app = {
+ .selector = idtype,
+ .protocol = id,
+ };
+
+ if ((pf->dcbx_cap & DCB_CAP_DCBX_LLD_MANAGED) ||
+ !(pf->dcbx_cap & DCB_CAP_DCBX_VER_CEE))
+ return -EINVAL;
+
+ return dcb_getapp(netdev, &app);
+}
+
+/**
+ * ice_dcbnl_find_app - Search for APP in given DCB config
+ * @cfg: struct to hold DCBX config
+ * @app: struct to hold app data to look for
+ */
+static bool
+ice_dcbnl_find_app(struct ice_dcbx_cfg *cfg,
+ struct ice_dcb_app_priority_table *app)
+{
+ int i;
+
+ for (i = 0; i < cfg->numapps; i++) {
+ if (app->selector == cfg->app[i].selector &&
+ app->prot_id == cfg->app[i].prot_id &&
+ app->priority == cfg->app[i].priority)
+ return true;
+ }
+
+ return false;
+}
+
+/**
+ * ice_dcbnl_setapp - set local IEEE App config
+ * @netdev: relevant netdev struct
+ * @app: struct to hold app config info
+ */
+static int ice_dcbnl_setapp(struct net_device *netdev, struct dcb_app *app)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+ struct ice_dcb_app_priority_table new_app;
+ struct ice_dcbx_cfg *old_cfg, *new_cfg;
+ int ret;
+
+ if ((pf->dcbx_cap & DCB_CAP_DCBX_LLD_MANAGED) ||
+ !(pf->dcbx_cap & DCB_CAP_DCBX_VER_IEEE))
+ return -EINVAL;
+
+ mutex_lock(&pf->tc_mutex);
+
+ new_cfg = &pf->hw.port_info->desired_dcbx_cfg;
+
+ old_cfg = &pf->hw.port_info->local_dcbx_cfg;
+
+ if (old_cfg->numapps == ICE_DCBX_MAX_APPS) {
+ ret = -EINVAL;
+ goto setapp_out;
+ }
+
+ ret = dcb_ieee_setapp(netdev, app);
+ if (ret)
+ goto setapp_out;
+
+ new_app.selector = app->selector;
+ new_app.prot_id = app->protocol;
+ new_app.priority = app->priority;
+ if (ice_dcbnl_find_app(old_cfg, &new_app)) {
+ ret = 0;
+ goto setapp_out;
+ }
+
+ new_cfg->app[new_cfg->numapps++] = new_app;
+ ret = ice_pf_dcb_cfg(pf, new_cfg, true);
+ /* return of zero indicates new cfg applied */
+ if (ret == ICE_DCB_HW_CHG_RST)
+ ice_dcbnl_devreset(netdev);
+ if (ret == ICE_DCB_NO_HW_CHG)
+ ret = ICE_DCB_HW_CHG_RST;
+
+setapp_out:
+ mutex_unlock(&pf->tc_mutex);
+ return ret;
+}
+
+/**
+ * ice_dcbnl_delapp - Delete local IEEE App config
+ * @netdev: relevant netdev
+ * @app: struct to hold app too delete
+ *
+ * Will not delete first application required by the FW
+ */
+static int ice_dcbnl_delapp(struct net_device *netdev, struct dcb_app *app)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+ struct ice_dcbx_cfg *old_cfg, *new_cfg;
+ int i, j, ret = 0;
+
+ if (pf->dcbx_cap & DCB_CAP_DCBX_LLD_MANAGED)
+ return -EINVAL;
+
+ mutex_lock(&pf->tc_mutex);
+ ret = dcb_ieee_delapp(netdev, app);
+ if (ret)
+ goto delapp_out;
+
+ old_cfg = &pf->hw.port_info->local_dcbx_cfg;
+
+ if (old_cfg->numapps == 1)
+ goto delapp_out;
+
+ new_cfg = &pf->hw.port_info->desired_dcbx_cfg;
+
+ for (i = 1; i < new_cfg->numapps; i++) {
+ if (app->selector == new_cfg->app[i].selector &&
+ app->protocol == new_cfg->app[i].prot_id &&
+ app->priority == new_cfg->app[i].priority) {
+ new_cfg->app[i].selector = 0;
+ new_cfg->app[i].prot_id = 0;
+ new_cfg->app[i].priority = 0;
+ break;
+ }
+ }
+
+ /* Did not find DCB App */
+ if (i == new_cfg->numapps) {
+ ret = -EINVAL;
+ goto delapp_out;
+ }
+
+ new_cfg->numapps--;
+
+ for (j = i; j < new_cfg->numapps; j++) {
+ new_cfg->app[i].selector = old_cfg->app[j + 1].selector;
+ new_cfg->app[i].prot_id = old_cfg->app[j + 1].prot_id;
+ new_cfg->app[i].priority = old_cfg->app[j + 1].priority;
+ }
+
+ ret = ice_pf_dcb_cfg(pf, new_cfg, true);
+ /* return of zero indicates new cfg applied */
+ if (ret == ICE_DCB_HW_CHG_RST)
+ ice_dcbnl_devreset(netdev);
+ if (ret == ICE_DCB_NO_HW_CHG)
+ ret = ICE_DCB_HW_CHG_RST;
+
+delapp_out:
+ mutex_unlock(&pf->tc_mutex);
+ return ret;
+}
+
+/**
+ * ice_dcbnl_cee_set_all - Commit CEE DCB settings to HW
+ * @netdev: the corresponding netdev
+ */
+static u8 ice_dcbnl_cee_set_all(struct net_device *netdev)
+{
+ struct ice_pf *pf = ice_netdev_to_pf(netdev);
+ struct ice_dcbx_cfg *new_cfg;
+ int err;
+
+ if ((pf->dcbx_cap & DCB_CAP_DCBX_LLD_MANAGED) ||
+ !(pf->dcbx_cap & DCB_CAP_DCBX_VER_CEE))
+ return ICE_DCB_NO_HW_CHG;
+
+ new_cfg = &pf->hw.port_info->desired_dcbx_cfg;
+
+ mutex_lock(&pf->tc_mutex);
+
+ err = ice_pf_dcb_cfg(pf, new_cfg, true);
+
+ mutex_unlock(&pf->tc_mutex);
+ return (err != ICE_DCB_HW_CHG_RST) ? ICE_DCB_NO_HW_CHG : err;
+}
+
+static const struct dcbnl_rtnl_ops dcbnl_ops = {
+ /* IEEE 802.1Qaz std */
+ .ieee_getets = ice_dcbnl_getets,
+ .ieee_setets = ice_dcbnl_setets,
+ .ieee_getpfc = ice_dcbnl_getpfc,
+ .ieee_setpfc = ice_dcbnl_setpfc,
+ .ieee_setapp = ice_dcbnl_setapp,
+ .ieee_delapp = ice_dcbnl_delapp,
+
+ /* CEE std */
+ .getstate = ice_dcbnl_getstate,
+ .setstate = ice_dcbnl_setstate,
+ .getpermhwaddr = ice_dcbnl_get_perm_hw_addr,
+ .setpgtccfgtx = ice_dcbnl_set_pg_tc_cfg_tx,
+ .setpgbwgcfgtx = ice_dcbnl_set_pg_bwg_cfg_tx,
+ .getpgtccfgtx = ice_dcbnl_get_pg_tc_cfg_tx,
+ .getpgbwgcfgtx = ice_dcbnl_get_pg_bwg_cfg_tx,
+ .getpgtccfgrx = ice_dcbnl_get_pg_tc_cfg_rx,
+ .getpgbwgcfgrx = ice_dcbnl_get_pg_bwg_cfg_rx,
+ .setpfccfg = ice_dcbnl_set_pfc_cfg,
+ .getpfccfg = ice_dcbnl_get_pfc_cfg,
+ .setall = ice_dcbnl_cee_set_all,
+ .getcap = ice_dcbnl_get_cap,
+ .getnumtcs = ice_dcbnl_getnumtcs,
+ .getpfcstate = ice_dcbnl_getpfcstate,
+ .getapp = ice_dcbnl_getapp,
+
+ /* DCBX configuration */
+ .getdcbx = ice_dcbnl_getdcbx,
+ .setdcbx = ice_dcbnl_setdcbx,
+};
+
+/**
+ * ice_dcbnl_set_all - set all the apps and ieee data from DCBX config
+ * @vsi: pointer to VSI struct
+ */
+void ice_dcbnl_set_all(struct ice_vsi *vsi)
+{
+ struct net_device *netdev = vsi->netdev;
+ struct ice_dcbx_cfg *dcbxcfg;
+ struct ice_port_info *pi;
+ struct dcb_app sapp;
+ struct ice_pf *pf;
+ int i;
+
+ if (!netdev)
+ return;
+
+ pf = ice_netdev_to_pf(netdev);
+ pi = pf->hw.port_info;
+
+ /* SW DCB taken care of by SW Default Config */
+ if (pf->dcbx_cap & DCB_CAP_DCBX_HOST)
+ return;
+
+ /* DCB not enabled */
+ if (!test_bit(ICE_FLAG_DCB_ENA, pf->flags))
+ return;
+
+ dcbxcfg = &pi->local_dcbx_cfg;
+
+ for (i = 0; i < dcbxcfg->numapps; i++) {
+ u8 prio, tc_map;
+
+ prio = dcbxcfg->app[i].priority;
+ tc_map = BIT(dcbxcfg->etscfg.prio_table[prio]);
+
+ /* Add APP only if the TC is enabled for this VSI */
+ if (tc_map & vsi->tc_cfg.ena_tc) {
+ sapp.selector = dcbxcfg->app[i].selector;
+ sapp.protocol = dcbxcfg->app[i].prot_id;
+ sapp.priority = prio;
+ dcb_ieee_setapp(netdev, &sapp);
+ }
+ }
+ /* Notify user-space of the changes */
+ dcbnl_ieee_notify(netdev, RTM_SETDCB, DCB_CMD_IEEE_SET, 0, 0);
+}
+
+/**
+ * ice_dcbnl_vsi_del_app - Delete APP on all VSIs
+ * @vsi: pointer to the main VSI
+ * @app: APP to delete
+ *
+ * Delete given APP from all the VSIs for given PF
+ */
+static void
+ice_dcbnl_vsi_del_app(struct ice_vsi *vsi,
+ struct ice_dcb_app_priority_table *app)
+{
+ struct dcb_app sapp;
+ int err;
+
+ sapp.selector = app->selector;
+ sapp.protocol = app->prot_id;
+ sapp.priority = app->priority;
+ err = ice_dcbnl_delapp(vsi->netdev, &sapp);
+ dev_dbg(&vsi->back->pdev->dev,
+ "Deleting app for VSI idx=%d err=%d sel=%d proto=0x%x, prio=%d\n",
+ vsi->idx, err, app->selector, app->prot_id, app->priority);
+}
+
+/**
+ * ice_dcbnl_flush_apps - Delete all removed APPs
+ * @pf: the corresponding PF
+ * @old_cfg: old DCBX configuration data
+ * @new_cfg: new DCBX configuration data
+ *
+ * Find and delete all APPS that are not present in the passed
+ * DCB configuration
+ */
+void
+ice_dcbnl_flush_apps(struct ice_pf *pf, struct ice_dcbx_cfg *old_cfg,
+ struct ice_dcbx_cfg *new_cfg)
+{
+ struct ice_vsi *main_vsi = ice_get_main_vsi(pf);
+ int i;
+
+ if (!main_vsi)
+ return;
+
+ for (i = 0; i < old_cfg->numapps; i++) {
+ struct ice_dcb_app_priority_table app = old_cfg->app[i];
+
+ /* The APP is not available anymore delete it */
+ if (!ice_dcbnl_find_app(new_cfg, &app))
+ ice_dcbnl_vsi_del_app(main_vsi, &app);
+ }
+}
+
+/**
+ * ice_dcbnl_setup - setup DCBNL
+ * @vsi: VSI to get associated netdev from
+ */
+void ice_dcbnl_setup(struct ice_vsi *vsi)
+{
+ struct net_device *netdev = vsi->netdev;
+ struct ice_pf *pf;
+
+ pf = ice_netdev_to_pf(netdev);
+ if (!test_bit(ICE_FLAG_DCB_CAPABLE, pf->flags))
+ return;
+
+ netdev->dcbnl_ops = &dcbnl_ops;
+ ice_dcbnl_set_all(vsi);
+}
diff --git a/drivers/net/ethernet/intel/ice/ice_dcb_nl.h b/drivers/net/ethernet/intel/ice/ice_dcb_nl.h
new file mode 100644
index 000000000000..6c630a362293
--- /dev/null
+++ b/drivers/net/ethernet/intel/ice/ice_dcb_nl.h
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (c) 2019, Intel Corporation. */
+
+#ifndef _ICE_DCB_NL_H_
+#define _ICE_DCB_NL_H_
+
+#ifdef CONFIG_DCB
+void ice_dcbnl_setup(struct ice_vsi *vsi);
+void ice_dcbnl_set_all(struct ice_vsi *vsi);
+void
+ice_dcbnl_flush_apps(struct ice_pf *pf, struct ice_dcbx_cfg *old_cfg,
+ struct ice_dcbx_cfg *new_cfg);
+#else
+#define ice_dcbnl_setup(vsi) do {} while (0)
+#define ice_dcbnl_set_all(vsi) do {} while (0)
+#define ice_dcbnl_flush_apps(pf, old_cfg, new_cfg) do {} while (0)
+#endif /* CONFIG_DCB */
+
+#endif /* _ICE_DCB_NL_H_ */
diff --git a/drivers/net/ethernet/intel/ice/ice_hw_autogen.h b/drivers/net/ethernet/intel/ice/ice_hw_autogen.h
index 8abfec62a777..1aa8e850bc67 100644
--- a/drivers/net/ethernet/intel/ice/ice_hw_autogen.h
+++ b/drivers/net/ethernet/intel/ice/ice_hw_autogen.h
@@ -52,6 +52,9 @@
#define PF_MBX_ATQLEN_ATQLEN_M ICE_M(0x3FF, 0)
#define PF_MBX_ATQLEN_ATQENABLE_M BIT(31)
#define PF_MBX_ATQT 0x0022E300
+#define PRTDCB_GENC 0x00083000
+#define PRTDCB_GENC_PFCLDA_S 16
+#define PRTDCB_GENC_PFCLDA_M ICE_M(0xFFFF, 16)
#define PRTDCB_GENS 0x00083020
#define PRTDCB_GENS_DCBX_STATUS_S 0
#define PRTDCB_GENS_DCBX_STATUS_M ICE_M(0x7, 0)
diff --git a/drivers/net/ethernet/intel/ice/ice_lib.c b/drivers/net/ethernet/intel/ice/ice_lib.c
index 8dd7f3848c59..d4e3df6544f5 100644
--- a/drivers/net/ethernet/intel/ice/ice_lib.c
+++ b/drivers/net/ethernet/intel/ice/ice_lib.c
@@ -2488,6 +2488,7 @@ int ice_vsi_rebuild(struct ice_vsi *vsi)
bool ice_is_reset_in_progress(unsigned long *state)
{
return test_bit(__ICE_RESET_OICR_RECV, state) ||
+ test_bit(__ICE_DCBNL_DEVRESET, state) ||
test_bit(__ICE_PFR_REQ, state) ||
test_bit(__ICE_CORER_REQ, state) ||
test_bit(__ICE_GLOBR_REQ, state);
diff --git a/drivers/net/ethernet/intel/ice/ice_main.c b/drivers/net/ethernet/intel/ice/ice_main.c
index fec58433bafb..a0a04114d991 100644
--- a/drivers/net/ethernet/intel/ice/ice_main.c
+++ b/drivers/net/ethernet/intel/ice/ice_main.c
@@ -9,6 +9,7 @@
#include "ice_base.h"
#include "ice_lib.h"
#include "ice_dcb_lib.h"
+#include "ice_dcb_nl.h"
#define DRV_VERSION_MAJOR 0
#define DRV_VERSION_MINOR 8
@@ -2641,6 +2642,9 @@ static int ice_setup_pf_sw(struct ice_pf *pf)
/* netdev has to be configured before setting frame size */
ice_vsi_cfg_frame_size(vsi);
+ /* Setup DCB netlink interface */
+ ice_dcbnl_setup(vsi);
+
/* registering the NAPI handler requires both the queues and
* netdev to be created, which are done in ice_pf_vsi_setup()
* and ice_cfg_netdev() respectively
@@ -2721,6 +2725,7 @@ static void ice_deinit_pf(struct ice_pf *pf)
{
ice_service_task_stop(pf);
mutex_destroy(&pf->sw_mutex);
+ mutex_destroy(&pf->tc_mutex);
mutex_destroy(&pf->avail_q_mutex);
if (pf->avail_txqs) {
@@ -2770,6 +2775,7 @@ static int ice_init_pf(struct ice_pf *pf)
ice_set_pf_caps(pf);
mutex_init(&pf->sw_mutex);
+ mutex_init(&pf->tc_mutex);
/* setup service timer and periodic service task */
timer_setup(&pf->serv_tmr, ice_service_timer, 0);
--
2.20.1
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Intel-wired-lan] [PATCH S32 03/15] ice: Implement DCBNL support
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 03/15] ice: Implement DCBNL support Tony Nguyen
@ 2019-11-01 16:41 ` Bowers, AndrewX
0 siblings, 0 replies; 30+ messages in thread
From: Bowers, AndrewX @ 2019-11-01 16:41 UTC (permalink / raw)
To: intel-wired-lan
> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On
> Behalf Of Tony Nguyen
> Sent: Friday, October 25, 2019 7:34 AM
> To: intel-wired-lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [PATCH S32 03/15] ice: Implement DCBNL support
>
> From: Dave Ertman <david.m.ertman@intel.com>
>
> Implement interface layer for the DCBNL subsystem. These are the functions
> to support the callbacks defined in the dcbnl_rtnl_ops struct. These callbacks
> are going to be used to interface with the DCB settings of the device.
> Implementation of dcb_nl set functions and supporting SW DCB functions.
>
> Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
> ---
> drivers/net/ethernet/intel/ice/Makefile | 2 +-
> drivers/net/ethernet/intel/ice/ice.h | 2 +
> drivers/net/ethernet/intel/ice/ice_dcb_lib.c | 15 +-
> drivers/net/ethernet/intel/ice/ice_dcb_lib.h | 15 +-
> drivers/net/ethernet/intel/ice/ice_dcb_nl.c | 933 ++++++++++++++++++
> drivers/net/ethernet/intel/ice/ice_dcb_nl.h | 19 +
> .../net/ethernet/intel/ice/ice_hw_autogen.h | 3 +
> drivers/net/ethernet/intel/ice/ice_lib.c | 1 +
> drivers/net/ethernet/intel/ice/ice_main.c | 6 +
> 9 files changed, 991 insertions(+), 5 deletions(-) create mode 100644
> drivers/net/ethernet/intel/ice/ice_dcb_nl.c
> create mode 100644 drivers/net/ethernet/intel/ice/ice_dcb_nl.h
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
^ permalink raw reply [flat|nested] 30+ messages in thread
* [Intel-wired-lan] [PATCH S32 04/15] ice: avoid setting features during reset
2019-10-25 14:34 [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and ice_dis_vsi in DCB configuration flow Tony Nguyen
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 02/15] ice: Add NDO callback to set the maximum per-queue bitrate Tony Nguyen
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 03/15] ice: Implement DCBNL support Tony Nguyen
@ 2019-10-25 14:34 ` Tony Nguyen
2019-11-01 16:42 ` Bowers, AndrewX
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 05/15] ice: Fix to change Rx/Tx ring descriptor size via ethtool with DCBx Tony Nguyen
` (11 subsequent siblings)
14 siblings, 1 reply; 30+ messages in thread
From: Tony Nguyen @ 2019-10-25 14:34 UTC (permalink / raw)
To: intel-wired-lan
From: Henry Tieman <henry.w.tieman@intel.com>
Certain subsystems behave very badly when called during reset (core
dump). This patch returns -EBUSY when reconfiguring some subsystems
during reset. With this patch some ethtool functions will not core
dump during reset.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
---
drivers/net/ethernet/intel/ice/ice_main.c | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/drivers/net/ethernet/intel/ice/ice_main.c b/drivers/net/ethernet/intel/ice/ice_main.c
index a0a04114d991..94354b307a4e 100644
--- a/drivers/net/ethernet/intel/ice/ice_main.c
+++ b/drivers/net/ethernet/intel/ice/ice_main.c
@@ -3924,6 +3924,7 @@ ice_set_features(struct net_device *netdev, netdev_features_t features)
{
struct ice_netdev_priv *np = netdev_priv(netdev);
struct ice_vsi *vsi = np->vsi;
+ struct ice_pf *pf = vsi->back;
int ret = 0;
/* Don't set any netdev advanced features with device in Safe Mode */
@@ -3933,6 +3934,13 @@ ice_set_features(struct net_device *netdev, netdev_features_t features)
return ret;
}
+ /* Do not change setting during reset */
+ if (ice_is_reset_in_progress(pf->state)) {
+ dev_err(&vsi->back->pdev->dev,
+ "Device is resetting, changing advanced netdev features temporarily unavailable.\n");
+ return -EBUSY;
+ }
+
/* Multiple features can be changed in one call so keep features in
* separate if/else statements to guarantee each feature is checked
*/
--
2.20.1
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Intel-wired-lan] [PATCH S32 04/15] ice: avoid setting features during reset
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 04/15] ice: avoid setting features during reset Tony Nguyen
@ 2019-11-01 16:42 ` Bowers, AndrewX
0 siblings, 0 replies; 30+ messages in thread
From: Bowers, AndrewX @ 2019-11-01 16:42 UTC (permalink / raw)
To: intel-wired-lan
> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On
> Behalf Of Tony Nguyen
> Sent: Friday, October 25, 2019 7:35 AM
> To: intel-wired-lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [PATCH S32 04/15] ice: avoid setting features
> during reset
>
> From: Henry Tieman <henry.w.tieman@intel.com>
>
> Certain subsystems behave very badly when called during reset (core dump).
> This patch returns -EBUSY when reconfiguring some subsystems during
> reset. With this patch some ethtool functions will not core dump during
> reset.
>
> Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
> ---
> drivers/net/ethernet/intel/ice/ice_main.c | 8 ++++++++
> 1 file changed, 8 insertions(+)
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
^ permalink raw reply [flat|nested] 30+ messages in thread
* [Intel-wired-lan] [PATCH S32 05/15] ice: Fix to change Rx/Tx ring descriptor size via ethtool with DCBx
2019-10-25 14:34 [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and ice_dis_vsi in DCB configuration flow Tony Nguyen
` (2 preceding siblings ...)
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 04/15] ice: avoid setting features during reset Tony Nguyen
@ 2019-10-25 14:34 ` Tony Nguyen
2019-11-01 16:42 ` Bowers, AndrewX
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 06/15] ice: configure software LLDP in ice_init_pf_dcb Tony Nguyen
` (10 subsequent siblings)
14 siblings, 1 reply; 30+ messages in thread
From: Tony Nguyen @ 2019-10-25 14:34 UTC (permalink / raw)
To: intel-wired-lan
From: Usha Ketineni <usha.k.ketineni@intel.com>
This patch fixes the call trace caused by the kernel when the Rx/Tx
descriptor size change request is initiated via ethtool when DCB is
configured. ice_set_ringparam() should use vsi->num_txq instead of
vsi->alloc_txq as it represents the queues that are enabled in the
driver when DCB is enabled/disabled. Otherwise, queue index being
used can go out of range.
For example, when vsi->alloc_txq has 104 queues and with 3 TCS enabled
via DCB, each TC gets 34 queues, vsi->num_txq will be 102 and only 102
queues will be enabled.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
---
drivers/net/ethernet/intel/ice/ice_ethtool.c | 14 +++++++-------
1 file changed, 7 insertions(+), 7 deletions(-)
diff --git a/drivers/net/ethernet/intel/ice/ice_ethtool.c b/drivers/net/ethernet/intel/ice/ice_ethtool.c
index 67d884e27ea4..3b9d33ad23d8 100644
--- a/drivers/net/ethernet/intel/ice/ice_ethtool.c
+++ b/drivers/net/ethernet/intel/ice/ice_ethtool.c
@@ -2743,14 +2743,14 @@ ice_set_ringparam(struct net_device *netdev, struct ethtool_ringparam *ring)
netdev_info(netdev, "Changing Tx descriptor count from %d to %d\n",
vsi->tx_rings[0]->count, new_tx_cnt);
- tx_rings = devm_kcalloc(&pf->pdev->dev, vsi->alloc_txq,
+ tx_rings = devm_kcalloc(&pf->pdev->dev, vsi->num_txq,
sizeof(*tx_rings), GFP_KERNEL);
if (!tx_rings) {
err = -ENOMEM;
goto done;
}
- for (i = 0; i < vsi->alloc_txq; i++) {
+ ice_for_each_txq(vsi, i) {
/* clone ring and setup updated count */
tx_rings[i] = *vsi->tx_rings[i];
tx_rings[i].count = new_tx_cnt;
@@ -2803,14 +2803,14 @@ ice_set_ringparam(struct net_device *netdev, struct ethtool_ringparam *ring)
netdev_info(netdev, "Changing Rx descriptor count from %d to %d\n",
vsi->rx_rings[0]->count, new_rx_cnt);
- rx_rings = devm_kcalloc(&pf->pdev->dev, vsi->alloc_rxq,
+ rx_rings = devm_kcalloc(&pf->pdev->dev, vsi->num_rxq,
sizeof(*rx_rings), GFP_KERNEL);
if (!rx_rings) {
err = -ENOMEM;
goto done;
}
- for (i = 0; i < vsi->alloc_rxq; i++) {
+ ice_for_each_rxq(vsi, i) {
/* clone ring and setup updated count */
rx_rings[i] = *vsi->rx_rings[i];
rx_rings[i].count = new_rx_cnt;
@@ -2848,7 +2848,7 @@ ice_set_ringparam(struct net_device *netdev, struct ethtool_ringparam *ring)
ice_down(vsi);
if (tx_rings) {
- for (i = 0; i < vsi->alloc_txq; i++) {
+ ice_for_each_txq(vsi, i) {
ice_free_tx_ring(vsi->tx_rings[i]);
*vsi->tx_rings[i] = tx_rings[i];
}
@@ -2856,7 +2856,7 @@ ice_set_ringparam(struct net_device *netdev, struct ethtool_ringparam *ring)
}
if (rx_rings) {
- for (i = 0; i < vsi->alloc_rxq; i++) {
+ ice_for_each_rxq(vsi, i) {
ice_free_rx_ring(vsi->rx_rings[i]);
/* copy the real tail offset */
rx_rings[i].tail = vsi->rx_rings[i]->tail;
@@ -2890,7 +2890,7 @@ ice_set_ringparam(struct net_device *netdev, struct ethtool_ringparam *ring)
free_tx:
/* error cleanup if the Rx allocations failed after getting Tx */
if (tx_rings) {
- for (i = 0; i < vsi->alloc_txq; i++)
+ ice_for_each_txq(vsi, i)
ice_free_tx_ring(&tx_rings[i]);
devm_kfree(&pf->pdev->dev, tx_rings);
}
--
2.20.1
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Intel-wired-lan] [PATCH S32 05/15] ice: Fix to change Rx/Tx ring descriptor size via ethtool with DCBx
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 05/15] ice: Fix to change Rx/Tx ring descriptor size via ethtool with DCBx Tony Nguyen
@ 2019-11-01 16:42 ` Bowers, AndrewX
0 siblings, 0 replies; 30+ messages in thread
From: Bowers, AndrewX @ 2019-11-01 16:42 UTC (permalink / raw)
To: intel-wired-lan
> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On
> Behalf Of Tony Nguyen
> Sent: Friday, October 25, 2019 7:35 AM
> To: intel-wired-lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [PATCH S32 05/15] ice: Fix to change Rx/Tx ring
> descriptor size via ethtool with DCBx
>
> From: Usha Ketineni <usha.k.ketineni@intel.com>
>
> This patch fixes the call trace caused by the kernel when the Rx/Tx descriptor
> size change request is initiated via ethtool when DCB is configured.
> ice_set_ringparam() should use vsi->num_txq instead of
> vsi->alloc_txq as it represents the queues that are enabled in the
> driver when DCB is enabled/disabled. Otherwise, queue index being used
> can go out of range.
>
> For example, when vsi->alloc_txq has 104 queues and with 3 TCS enabled via
> DCB, each TC gets 34 queues, vsi->num_txq will be 102 and only 102 queues
> will be enabled.
>
> Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
> ---
> drivers/net/ethernet/intel/ice/ice_ethtool.c | 14 +++++++-------
> 1 file changed, 7 insertions(+), 7 deletions(-)
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
^ permalink raw reply [flat|nested] 30+ messages in thread
* [Intel-wired-lan] [PATCH S32 06/15] ice: configure software LLDP in ice_init_pf_dcb
2019-10-25 14:34 [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and ice_dis_vsi in DCB configuration flow Tony Nguyen
` (3 preceding siblings ...)
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 05/15] ice: Fix to change Rx/Tx ring descriptor size via ethtool with DCBx Tony Nguyen
@ 2019-10-25 14:34 ` Tony Nguyen
2019-11-01 16:42 ` Bowers, AndrewX
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 07/15] ice: Check if VF is disabled for Opcode and other operations Tony Nguyen
` (9 subsequent siblings)
14 siblings, 1 reply; 30+ messages in thread
From: Tony Nguyen @ 2019-10-25 14:34 UTC (permalink / raw)
To: intel-wired-lan
From: Paul Greenwalt <paul.greenwalt@intel.com>
Move software LLDP configuration when FW DCBX is disabled to
ice_init_pf_dcb, since that is where the FW DCBX state is determined.
Remove this software LLDP configuration from ice_vsi_setup and
ice_set_priv_flags. Software configuration includes redirecting Rx LLDP
packets up the stack, when FW DCBX is not running.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
---
drivers/net/ethernet/intel/ice/ice_dcb_lib.c | 15 +++++++++++++++
drivers/net/ethernet/intel/ice/ice_ethtool.c | 5 -----
drivers/net/ethernet/intel/ice/ice_lib.c | 14 ++++----------
3 files changed, 19 insertions(+), 15 deletions(-)
diff --git a/drivers/net/ethernet/intel/ice/ice_dcb_lib.c b/drivers/net/ethernet/intel/ice/ice_dcb_lib.c
index 737c85349503..70640874701f 100644
--- a/drivers/net/ethernet/intel/ice/ice_dcb_lib.c
+++ b/drivers/net/ethernet/intel/ice/ice_dcb_lib.c
@@ -593,6 +593,8 @@ int ice_init_pf_dcb(struct ice_pf *pf, bool locked)
"DCB is enabled in the hardware, max number of TCs supported on this port are %d\n",
pf->hw.func_caps.common_cap.maxtc);
if (err) {
+ struct ice_vsi *pf_vsi;
+
/* FW LLDP is disabled, activate SW DCBX/LLDP mode */
dev_info(&pf->pdev->dev,
"FW LLDP is disabled, DCBx/LLDP in SW mode.\n");
@@ -605,6 +607,19 @@ int ice_init_pf_dcb(struct ice_pf *pf, bool locked)
goto dcb_init_err;
}
+ /* If the FW DCBX engine is not running then Rx LLDP packets
+ * need to be redirected up the stack.
+ */
+ pf_vsi = ice_get_main_vsi(pf);
+ if (!pf_vsi) {
+ dev_err(&pf->pdev->dev,
+ "Failed to set local DCB config\n");
+ err = -EIO;
+ goto dcb_init_err;
+ }
+
+ ice_cfg_sw_lldp(pf_vsi, false, true);
+
pf->dcbx_cap = DCB_CAP_DCBX_HOST | DCB_CAP_DCBX_VER_IEEE;
return 0;
}
diff --git a/drivers/net/ethernet/intel/ice/ice_ethtool.c b/drivers/net/ethernet/intel/ice/ice_ethtool.c
index 3b9d33ad23d8..9c2045056d59 100644
--- a/drivers/net/ethernet/intel/ice/ice_ethtool.c
+++ b/drivers/net/ethernet/intel/ice/ice_ethtool.c
@@ -1295,11 +1295,6 @@ static int ice_set_priv_flags(struct net_device *netdev, u32 flags)
status = ice_init_pf_dcb(pf, true);
if (status)
dev_warn(&pf->pdev->dev, "Fail to init DCB\n");
-
- /* Forward LLDP packets to default VSI so that they
- * are passed up the stack
- */
- ice_cfg_sw_lldp(vsi, false, true);
} else {
enum ice_status status;
bool dcbx_agent_status;
diff --git a/drivers/net/ethernet/intel/ice/ice_lib.c b/drivers/net/ethernet/intel/ice/ice_lib.c
index d4e3df6544f5..c9e0b533da47 100644
--- a/drivers/net/ethernet/intel/ice/ice_lib.c
+++ b/drivers/net/ethernet/intel/ice/ice_lib.c
@@ -1881,23 +1881,17 @@ ice_vsi_setup(struct ice_pf *pf, struct ice_port_info *pi,
* out PAUSE or PFC frames. If enabled, FW can still send FC frames.
* The rule is added once for PF VSI in order to create appropriate
* recipe, since VSI/VSI list is ignored with drop action...
- * Also add rules to handle LLDP Tx and Rx packets. Tx LLDP packets
- * need to be dropped so that VFs cannot send LLDP packets to reconfig
- * DCB settings in the HW. Also, if the FW DCBX engine is not running
- * then Rx LLDP packets need to be redirected up the stack.
+ * Also add rules to handle LLDP Tx packets. Tx LLDP packets need to
+ * be dropped so that VFs cannot send LLDP packets to reconfig DCB
+ * settings in the HW.
*/
- if (!ice_is_safe_mode(pf)) {
+ if (!ice_is_safe_mode(pf))
if (vsi->type == ICE_VSI_PF) {
ice_vsi_add_rem_eth_mac(vsi, true);
/* Tx LLDP packets */
ice_cfg_sw_lldp(vsi, true, true);
-
- /* Rx LLDP packets */
- if (!test_bit(ICE_FLAG_FW_LLDP_AGENT, pf->flags))
- ice_cfg_sw_lldp(vsi, false, true);
}
- }
return vsi;
--
2.20.1
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Intel-wired-lan] [PATCH S32 06/15] ice: configure software LLDP in ice_init_pf_dcb
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 06/15] ice: configure software LLDP in ice_init_pf_dcb Tony Nguyen
@ 2019-11-01 16:42 ` Bowers, AndrewX
0 siblings, 0 replies; 30+ messages in thread
From: Bowers, AndrewX @ 2019-11-01 16:42 UTC (permalink / raw)
To: intel-wired-lan
> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On
> Behalf Of Tony Nguyen
> Sent: Friday, October 25, 2019 7:35 AM
> To: intel-wired-lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [PATCH S32 06/15] ice: configure software LLDP in
> ice_init_pf_dcb
>
> From: Paul Greenwalt <paul.greenwalt@intel.com>
>
> Move software LLDP configuration when FW DCBX is disabled to
> ice_init_pf_dcb, since that is where the FW DCBX state is determined.
> Remove this software LLDP configuration from ice_vsi_setup and
> ice_set_priv_flags. Software configuration includes redirecting Rx LLDP
> packets up the stack, when FW DCBX is not running.
>
> Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
> ---
> drivers/net/ethernet/intel/ice/ice_dcb_lib.c | 15 +++++++++++++++
> drivers/net/ethernet/intel/ice/ice_ethtool.c | 5 -----
> drivers/net/ethernet/intel/ice/ice_lib.c | 14 ++++----------
> 3 files changed, 19 insertions(+), 15 deletions(-)
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
^ permalink raw reply [flat|nested] 30+ messages in thread
* [Intel-wired-lan] [PATCH S32 07/15] ice: Check if VF is disabled for Opcode and other operations
2019-10-25 14:34 [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and ice_dis_vsi in DCB configuration flow Tony Nguyen
` (4 preceding siblings ...)
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 06/15] ice: configure software LLDP in ice_init_pf_dcb Tony Nguyen
@ 2019-10-25 14:34 ` Tony Nguyen
2019-11-01 16:43 ` Bowers, AndrewX
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 08/15] ice: Change max MSI-x vector_id check in cfg_irq_map Tony Nguyen
` (8 subsequent siblings)
14 siblings, 1 reply; 30+ messages in thread
From: Tony Nguyen @ 2019-10-25 14:34 UTC (permalink / raw)
To: intel-wired-lan
From: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
This patch adds code to check if PF or VF is disabled before honoring
mailbox message to configure VF - If it is disabled, and opcode is for
resetting VF, the PF driver simply tell VF that all is set. In addition,
if reset is ongoing, and Admin intend to configure VF on the host, we can
poll the VF enabling bit to make sure it is ready before continue - If
after ~250 milliseconds, VF is not in active state, we can bail out with
invalid error.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
---
.../net/ethernet/intel/ice/ice_virtchnl_pf.c | 74 ++++++++++++++++---
.../net/ethernet/intel/ice/ice_virtchnl_pf.h | 1 +
2 files changed, 63 insertions(+), 12 deletions(-)
diff --git a/drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c b/drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c
index 4a1cb51b50c7..537377448bef 100644
--- a/drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c
+++ b/drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c
@@ -1151,6 +1151,25 @@ bool ice_reset_all_vfs(struct ice_pf *pf, bool is_vflr)
return true;
}
+/**
+ * ice_is_vf_disabled
+ * @vf: pointer to the VF info
+ *
+ * Returns true if the PF or VF is disabled, false otherwise.
+ */
+static bool ice_is_vf_disabled(struct ice_vf *vf)
+{
+ struct ice_pf *pf = vf->pf;
+
+ /* If the PF has been disabled, there is no need resetting VF until
+ * PF is active again. Similarly, if the VF has been disabled, this
+ * means something else is resetting the VF, so we shouldn't continue.
+ * Otherwise, set disable VF state bit for actual reset, and continue.
+ */
+ return (test_bit(__ICE_VF_DIS, pf->state) ||
+ test_bit(ICE_VF_STATE_DIS, vf->vf_states));
+}
+
/**
* ice_reset_vf - Reset a particular VF
* @vf: pointer to the VF structure
@@ -1168,19 +1187,15 @@ static bool ice_reset_vf(struct ice_vf *vf, bool is_vflr)
u32 reg;
int i;
- /* If the PF has been disabled, there is no need resetting VF until
- * PF is active again.
- */
- if (test_bit(__ICE_VF_DIS, pf->state))
- return false;
-
- /* If the VF has been disabled, this means something else is
- * resetting the VF, so we shouldn't continue. Otherwise, set
- * disable VF state bit for actual reset, and continue.
- */
- if (test_and_set_bit(ICE_VF_STATE_DIS, vf->vf_states))
- return false;
+ if (ice_is_vf_disabled(vf)) {
+ dev_dbg(&pf->pdev->dev,
+ "VF is already disabled, there is no need for resetting it, telling VM, all is fine %d\n",
+ vf->vf_id);
+ return true;
+ }
+ /* Set VF disable bit state here, before triggering reset */
+ set_bit(ICE_VF_STATE_DIS, vf->vf_states);
ice_trigger_vf_reset(vf, is_vflr, false);
vsi = pf->vsi[vf->lan_vsi_idx];
@@ -3128,6 +3143,23 @@ int ice_set_vf_spoofchk(struct net_device *netdev, int vf_id, bool ena)
return ret;
}
+/**
+ * ice_wait_on_vf_reset
+ * @vf: The VF being resseting
+ *
+ * Poll to make sure a given VF is ready after reset
+ */
+static void ice_wait_on_vf_reset(struct ice_vf *vf)
+{
+ int i;
+
+ for (i = 0; i < ICE_MAX_VF_RESET_WAIT; i++) {
+ if (test_bit(ICE_VF_STATE_INIT, vf->vf_states))
+ break;
+ msleep(20);
+ }
+}
+
/**
* ice_set_vf_mac
* @netdev: network interface device structure
@@ -3151,6 +3183,15 @@ int ice_set_vf_mac(struct net_device *netdev, int vf_id, u8 *mac)
}
vf = &pf->vf[vf_id];
+ /* Don't set MAC on disabled VF */
+ if (ice_is_vf_disabled(vf))
+ return -EINVAL;
+
+ /* In case VF is in reset mode, wait until it is completed. Depending
+ * on factors like queue disabling routine, this could take ~250ms
+ */
+ ice_wait_on_vf_reset(vf);
+
if (!test_bit(ICE_VF_STATE_INIT, vf->vf_states)) {
netdev_err(netdev, "VF %d in reset. Try again.\n", vf_id);
return -EBUSY;
@@ -3198,6 +3239,15 @@ int ice_set_vf_trust(struct net_device *netdev, int vf_id, bool trusted)
}
vf = &pf->vf[vf_id];
+ /* Don't set Trusted Mode on disabled VF */
+ if (ice_is_vf_disabled(vf))
+ return -EINVAL;
+
+ /* In case VF is in reset mode, wait until it is completed. Depending
+ * on factors like queue disabling routine, this could take ~250ms
+ */
+ ice_wait_on_vf_reset(vf);
+
if (!test_bit(ICE_VF_STATE_INIT, vf->vf_states)) {
dev_err(&pf->pdev->dev, "VF %d in reset. Try again.\n", vf_id);
return -EBUSY;
diff --git a/drivers/net/ethernet/intel/ice/ice_virtchnl_pf.h b/drivers/net/ethernet/intel/ice/ice_virtchnl_pf.h
index 0d9880c8bba3..2e867ad2e81d 100644
--- a/drivers/net/ethernet/intel/ice/ice_virtchnl_pf.h
+++ b/drivers/net/ethernet/intel/ice/ice_virtchnl_pf.h
@@ -38,6 +38,7 @@
#define ICE_MAX_POLICY_INTR_PER_VF 33
#define ICE_MIN_INTR_PER_VF (ICE_MIN_QS_PER_VF + 1)
#define ICE_DFLT_INTR_PER_VF (ICE_DFLT_QS_PER_VF + 1)
+#define ICE_MAX_VF_RESET_WAIT 15
/* Specific VF states */
enum ice_vf_states {
--
2.20.1
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Intel-wired-lan] [PATCH S32 07/15] ice: Check if VF is disabled for Opcode and other operations
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 07/15] ice: Check if VF is disabled for Opcode and other operations Tony Nguyen
@ 2019-11-01 16:43 ` Bowers, AndrewX
0 siblings, 0 replies; 30+ messages in thread
From: Bowers, AndrewX @ 2019-11-01 16:43 UTC (permalink / raw)
To: intel-wired-lan
> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On
> Behalf Of Tony Nguyen
> Sent: Friday, October 25, 2019 7:35 AM
> To: intel-wired-lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [PATCH S32 07/15] ice: Check if VF is disabled for
> Opcode and other operations
>
> From: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
>
> This patch adds code to check if PF or VF is disabled before honoring mailbox
> message to configure VF - If it is disabled, and opcode is for resetting VF, the
> PF driver simply tell VF that all is set. In addition, if reset is ongoing, and
> Admin intend to configure VF on the host, we can poll the VF enabling bit to
> make sure it is ready before continue - If after ~250 milliseconds, VF is not in
> active state, we can bail out with invalid error.
>
> Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
> ---
> .../net/ethernet/intel/ice/ice_virtchnl_pf.c | 74 ++++++++++++++++---
> .../net/ethernet/intel/ice/ice_virtchnl_pf.h | 1 +
> 2 files changed, 63 insertions(+), 12 deletions(-)
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
^ permalink raw reply [flat|nested] 30+ messages in thread
* [Intel-wired-lan] [PATCH S32 08/15] ice: Change max MSI-x vector_id check in cfg_irq_map
2019-10-25 14:34 [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and ice_dis_vsi in DCB configuration flow Tony Nguyen
` (5 preceding siblings ...)
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 07/15] ice: Check if VF is disabled for Opcode and other operations Tony Nguyen
@ 2019-10-25 14:34 ` Tony Nguyen
2019-11-01 16:43 ` Bowers, AndrewX
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 09/15] ice: use pkg_dwnld_status instead of sq_last_status Tony Nguyen
` (7 subsequent siblings)
14 siblings, 1 reply; 30+ messages in thread
From: Tony Nguyen @ 2019-10-25 14:34 UTC (permalink / raw)
To: intel-wired-lan
From: Brett Creeley <brett.creeley@intel.com>
Currently we check to make sure the vector_id passed down from iavf
is less than or equal to pf->hw.func_caps.common_caps.num_msix_vectors.
This is incorrect because the vector_id is always 0-based and never
greater than or equal to the ICE_MAX_INTR_PER_VF. Fix this by checking
to make sure the vector_id is less than the max allowed interrupts per
VF (ICE_MAX_INTR_PER_VF).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
---
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c | 8 +++++---
1 file changed, 5 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c b/drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c
index 537377448bef..eb526144a237 100644
--- a/drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c
+++ b/drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c
@@ -2179,9 +2179,11 @@ static int ice_vc_cfg_irq_map_msg(struct ice_vf *vf, u8 *msg)
vector_id = map->vector_id;
vsi_id = map->vsi_id;
- /* validate msg params */
- if (!(vector_id < pf->hw.func_caps.common_cap
- .num_msix_vectors) || !ice_vc_isvalid_vsi_id(vf, vsi_id) ||
+ /* vector_id is always 0-based for each VF, and can never be
+ * larger than or equal to the max allowed interrupts per VF
+ */
+ if (!(vector_id < ICE_MAX_INTR_PER_VF) ||
+ !ice_vc_isvalid_vsi_id(vf, vsi_id) ||
(!vector_id && (map->rxq_map || map->txq_map))) {
v_ret = VIRTCHNL_STATUS_ERR_PARAM;
goto error_param;
--
2.20.1
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Intel-wired-lan] [PATCH S32 08/15] ice: Change max MSI-x vector_id check in cfg_irq_map
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 08/15] ice: Change max MSI-x vector_id check in cfg_irq_map Tony Nguyen
@ 2019-11-01 16:43 ` Bowers, AndrewX
0 siblings, 0 replies; 30+ messages in thread
From: Bowers, AndrewX @ 2019-11-01 16:43 UTC (permalink / raw)
To: intel-wired-lan
> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On
> Behalf Of Tony Nguyen
> Sent: Friday, October 25, 2019 7:35 AM
> To: intel-wired-lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [PATCH S32 08/15] ice: Change max MSI-x
> vector_id check in cfg_irq_map
>
> From: Brett Creeley <brett.creeley@intel.com>
>
> Currently we check to make sure the vector_id passed down from iavf is less
> than or equal to pf->hw.func_caps.common_caps.num_msix_vectors.
> This is incorrect because the vector_id is always 0-based and never greater
> than or equal to the ICE_MAX_INTR_PER_VF. Fix this by checking to make
> sure the vector_id is less than the max allowed interrupts per VF
> (ICE_MAX_INTR_PER_VF).
>
> Signed-off-by: Brett Creeley <brett.creeley@intel.com>
> ---
> drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c | 8 +++++---
> 1 file changed, 5 insertions(+), 3 deletions(-)
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
^ permalink raw reply [flat|nested] 30+ messages in thread
* [Intel-wired-lan] [PATCH S32 09/15] ice: use pkg_dwnld_status instead of sq_last_status
2019-10-25 14:34 [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and ice_dis_vsi in DCB configuration flow Tony Nguyen
` (6 preceding siblings ...)
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 08/15] ice: Change max MSI-x vector_id check in cfg_irq_map Tony Nguyen
@ 2019-10-25 14:34 ` Tony Nguyen
2019-11-01 16:43 ` Bowers, AndrewX
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 10/15] ice: delay less Tony Nguyen
` (6 subsequent siblings)
14 siblings, 1 reply; 30+ messages in thread
From: Tony Nguyen @ 2019-10-25 14:34 UTC (permalink / raw)
To: intel-wired-lan
From: Bruce Allan <bruce.w.allan@intel.com>
Since the return value from the Download Package AQ command is stored in
hw->pkg_dwnld_status, use that instead of sq_last_status since that may
have the return value from some other AQ command leading to unexpected
results.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
---
drivers/net/ethernet/intel/ice/ice_main.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/intel/ice/ice_main.c b/drivers/net/ethernet/intel/ice/ice_main.c
index 94354b307a4e..aaa398759548 100644
--- a/drivers/net/ethernet/intel/ice/ice_main.c
+++ b/drivers/net/ethernet/intel/ice/ice_main.c
@@ -3025,7 +3025,7 @@ ice_log_pkg_init(struct ice_hw *hw, enum ice_status *status)
ICE_PKG_SUPP_VER_MAJ, ICE_PKG_SUPP_VER_MNR);
break;
case ICE_ERR_AQ_ERROR:
- switch (hw->adminq.sq_last_status) {
+ switch (hw->pkg_dwnld_status) {
case ICE_AQ_RC_ENOSEC:
case ICE_AQ_RC_EBADSIG:
dev_err(dev,
--
2.20.1
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Intel-wired-lan] [PATCH S32 09/15] ice: use pkg_dwnld_status instead of sq_last_status
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 09/15] ice: use pkg_dwnld_status instead of sq_last_status Tony Nguyen
@ 2019-11-01 16:43 ` Bowers, AndrewX
0 siblings, 0 replies; 30+ messages in thread
From: Bowers, AndrewX @ 2019-11-01 16:43 UTC (permalink / raw)
To: intel-wired-lan
> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On
> Behalf Of Tony Nguyen
> Sent: Friday, October 25, 2019 7:35 AM
> To: intel-wired-lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [PATCH S32 09/15] ice: use pkg_dwnld_status
> instead of sq_last_status
>
> From: Bruce Allan <bruce.w.allan@intel.com>
>
> Since the return value from the Download Package AQ command is stored in
> hw->pkg_dwnld_status, use that instead of sq_last_status since that may
> have the return value from some other AQ command leading to unexpected
> results.
>
> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
> ---
> drivers/net/ethernet/intel/ice/ice_main.c | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
^ permalink raw reply [flat|nested] 30+ messages in thread
* [Intel-wired-lan] [PATCH S32 10/15] ice: delay less
2019-10-25 14:34 [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and ice_dis_vsi in DCB configuration flow Tony Nguyen
` (7 preceding siblings ...)
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 09/15] ice: use pkg_dwnld_status instead of sq_last_status Tony Nguyen
@ 2019-10-25 14:34 ` Tony Nguyen
2019-11-01 16:44 ` Bowers, AndrewX
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 11/15] ice: Update enum ice_flg64_bits to current specification Tony Nguyen
` (5 subsequent siblings)
14 siblings, 1 reply; 30+ messages in thread
From: Tony Nguyen @ 2019-10-25 14:34 UTC (permalink / raw)
To: intel-wired-lan
From: Mitch Williams <mitch.a.williams@intel.com>
Shorten the delay for SQ responses, but increase the number of loops.
Max delay time is unchanged, but some operations complete much more
quickly.
In the process, add a new define to make the delay count and delay time
more explicit. Add comments to make things more explicit.
This fixes a problem with VF resets failing on with many VFs.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
---
drivers/net/ethernet/intel/ice/ice_controlq.c | 2 +-
drivers/net/ethernet/intel/ice/ice_controlq.h | 5 +++--
2 files changed, 4 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/intel/ice/ice_controlq.c b/drivers/net/ethernet/intel/ice/ice_controlq.c
index 2353166c654e..c68709c7ef81 100644
--- a/drivers/net/ethernet/intel/ice/ice_controlq.c
+++ b/drivers/net/ethernet/intel/ice/ice_controlq.c
@@ -948,7 +948,7 @@ ice_sq_send_cmd(struct ice_hw *hw, struct ice_ctl_q_info *cq,
if (ice_sq_done(hw, cq))
break;
- mdelay(1);
+ udelay(ICE_CTL_Q_SQ_CMD_USEC);
total_delay++;
} while (total_delay < cq->sq_cmd_timeout);
diff --git a/drivers/net/ethernet/intel/ice/ice_controlq.h b/drivers/net/ethernet/intel/ice/ice_controlq.h
index 44945c2165d8..4df9da359135 100644
--- a/drivers/net/ethernet/intel/ice/ice_controlq.h
+++ b/drivers/net/ethernet/intel/ice/ice_controlq.h
@@ -31,8 +31,9 @@ enum ice_ctl_q {
ICE_CTL_Q_MAILBOX,
};
-/* Control Queue default settings */
-#define ICE_CTL_Q_SQ_CMD_TIMEOUT 250 /* msecs */
+/* Control Queue timeout settings - max delay 250ms */
+#define ICE_CTL_Q_SQ_CMD_TIMEOUT 2500 /* Count 2500 times */
+#define ICE_CTL_Q_SQ_CMD_USEC 100 /* Check every 100usec */
struct ice_ctl_q_ring {
void *dma_head; /* Virtual address to DMA head */
--
2.20.1
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Intel-wired-lan] [PATCH S32 10/15] ice: delay less
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 10/15] ice: delay less Tony Nguyen
@ 2019-11-01 16:44 ` Bowers, AndrewX
0 siblings, 0 replies; 30+ messages in thread
From: Bowers, AndrewX @ 2019-11-01 16:44 UTC (permalink / raw)
To: intel-wired-lan
> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On
> Behalf Of Tony Nguyen
> Sent: Friday, October 25, 2019 7:35 AM
> To: intel-wired-lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [PATCH S32 10/15] ice: delay less
>
> From: Mitch Williams <mitch.a.williams@intel.com>
>
> Shorten the delay for SQ responses, but increase the number of loops.
> Max delay time is unchanged, but some operations complete much more
> quickly.
>
> In the process, add a new define to make the delay count and delay time
> more explicit. Add comments to make things more explicit.
>
> This fixes a problem with VF resets failing on with many VFs.
>
> Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
> ---
> drivers/net/ethernet/intel/ice/ice_controlq.c | 2 +-
> drivers/net/ethernet/intel/ice/ice_controlq.h | 5 +++--
> 2 files changed, 4 insertions(+), 3 deletions(-)
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
^ permalink raw reply [flat|nested] 30+ messages in thread
* [Intel-wired-lan] [PATCH S32 11/15] ice: Update enum ice_flg64_bits to current specification
2019-10-25 14:34 [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and ice_dis_vsi in DCB configuration flow Tony Nguyen
` (8 preceding siblings ...)
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 10/15] ice: delay less Tony Nguyen
@ 2019-10-25 14:34 ` Tony Nguyen
2019-11-01 16:44 ` Bowers, AndrewX
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 12/15] ice: remove unnecessary conditional check Tony Nguyen
` (4 subsequent siblings)
14 siblings, 1 reply; 30+ messages in thread
From: Tony Nguyen @ 2019-10-25 14:34 UTC (permalink / raw)
To: intel-wired-lan
From: Brett Creeley <brett.creeley@intel.com>
Currently the VLAN ice_flg64_bits are off by 1. Fix this by
setting the ICE_FLG_EVLAN_x8100 flag to 14, which also updates
ICE_FLG_EVLAN_x9100 to 15 and ICE_FLG_VLAN_x8100 to 16.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
---
drivers/net/ethernet/intel/ice/ice_lan_tx_rx.h | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/intel/ice/ice_lan_tx_rx.h b/drivers/net/ethernet/intel/ice/ice_lan_tx_rx.h
index 2aac8f13daeb..ad34f22d44ef 100644
--- a/drivers/net/ethernet/intel/ice/ice_lan_tx_rx.h
+++ b/drivers/net/ethernet/intel/ice/ice_lan_tx_rx.h
@@ -211,7 +211,7 @@ enum ice_flex_rx_mdid {
/* Rx/Tx Flag64 packet flag bits */
enum ice_flg64_bits {
ICE_FLG_PKT_DSI = 0,
- ICE_FLG_EVLAN_x8100 = 15,
+ ICE_FLG_EVLAN_x8100 = 14,
ICE_FLG_EVLAN_x9100,
ICE_FLG_VLAN_x8100,
ICE_FLG_TNL_MAC = 22,
--
2.20.1
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Intel-wired-lan] [PATCH S32 11/15] ice: Update enum ice_flg64_bits to current specification
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 11/15] ice: Update enum ice_flg64_bits to current specification Tony Nguyen
@ 2019-11-01 16:44 ` Bowers, AndrewX
0 siblings, 0 replies; 30+ messages in thread
From: Bowers, AndrewX @ 2019-11-01 16:44 UTC (permalink / raw)
To: intel-wired-lan
> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On
> Behalf Of Tony Nguyen
> Sent: Friday, October 25, 2019 7:35 AM
> To: intel-wired-lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [PATCH S32 11/15] ice: Update enum ice_flg64_bits
> to current specification
>
> From: Brett Creeley <brett.creeley@intel.com>
>
> Currently the VLAN ice_flg64_bits are off by 1. Fix this by setting the
> ICE_FLG_EVLAN_x8100 flag to 14, which also updates
> ICE_FLG_EVLAN_x9100 to 15 and ICE_FLG_VLAN_x8100 to 16.
>
> Signed-off-by: Brett Creeley <brett.creeley@intel.com>
> ---
> drivers/net/ethernet/intel/ice/ice_lan_tx_rx.h | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
^ permalink raw reply [flat|nested] 30+ messages in thread
* [Intel-wired-lan] [PATCH S32 12/15] ice: remove unnecessary conditional check
2019-10-25 14:34 [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and ice_dis_vsi in DCB configuration flow Tony Nguyen
` (9 preceding siblings ...)
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 11/15] ice: Update enum ice_flg64_bits to current specification Tony Nguyen
@ 2019-10-25 14:34 ` Tony Nguyen
2019-11-01 16:44 ` Bowers, AndrewX
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 13/15] ice: Introduce and use ice_vsi_type_str Tony Nguyen
` (3 subsequent siblings)
14 siblings, 1 reply; 30+ messages in thread
From: Tony Nguyen @ 2019-10-25 14:34 UTC (permalink / raw)
To: intel-wired-lan
From: Bruce Allan <bruce.w.allan@intel.com>
There is no reason to do this conditional check before the assignment so
simply remove it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
---
drivers/net/ethernet/intel/ice/ice_switch.c | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/intel/ice/ice_switch.c b/drivers/net/ethernet/intel/ice/ice_switch.c
index 1acdd43a2edd..77d211ea3aae 100644
--- a/drivers/net/ethernet/intel/ice/ice_switch.c
+++ b/drivers/net/ethernet/intel/ice/ice_switch.c
@@ -416,8 +416,7 @@ ice_add_vsi(struct ice_hw *hw, u16 vsi_handle, struct ice_vsi_ctx *vsi_ctx,
ice_save_vsi_ctx(hw, vsi_handle, tmp_vsi_ctx);
} else {
/* update with new HW VSI num */
- if (tmp_vsi_ctx->vsi_num != vsi_ctx->vsi_num)
- tmp_vsi_ctx->vsi_num = vsi_ctx->vsi_num;
+ tmp_vsi_ctx->vsi_num = vsi_ctx->vsi_num;
}
return 0;
--
2.20.1
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Intel-wired-lan] [PATCH S32 12/15] ice: remove unnecessary conditional check
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 12/15] ice: remove unnecessary conditional check Tony Nguyen
@ 2019-11-01 16:44 ` Bowers, AndrewX
0 siblings, 0 replies; 30+ messages in thread
From: Bowers, AndrewX @ 2019-11-01 16:44 UTC (permalink / raw)
To: intel-wired-lan
> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On
> Behalf Of Tony Nguyen
> Sent: Friday, October 25, 2019 7:35 AM
> To: intel-wired-lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [PATCH S32 12/15] ice: remove unnecessary
> conditional check
>
> From: Bruce Allan <bruce.w.allan@intel.com>
>
> There is no reason to do this conditional check before the assignment so
> simply remove it.
>
> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
> ---
> drivers/net/ethernet/intel/ice/ice_switch.c | 3 +--
> 1 file changed, 1 insertion(+), 2 deletions(-)
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
^ permalink raw reply [flat|nested] 30+ messages in thread
* [Intel-wired-lan] [PATCH S32 13/15] ice: Introduce and use ice_vsi_type_str
2019-10-25 14:34 [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and ice_dis_vsi in DCB configuration flow Tony Nguyen
` (10 preceding siblings ...)
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 12/15] ice: remove unnecessary conditional check Tony Nguyen
@ 2019-10-25 14:34 ` Tony Nguyen
2019-11-01 16:45 ` Bowers, AndrewX
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 14/15] ice: use more accurate ICE_DBG mask types Tony Nguyen
` (2 subsequent siblings)
14 siblings, 1 reply; 30+ messages in thread
From: Tony Nguyen @ 2019-10-25 14:34 UTC (permalink / raw)
To: intel-wired-lan
From: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
ice_vsi_type_str converts an ice_vsi_type enum value to its string
equivalent. This is expected to help easily identify VSI types from
module print statements.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
---
drivers/net/ethernet/intel/ice/ice_lib.c | 21 ++++++++++++++++++++-
drivers/net/ethernet/intel/ice/ice_lib.h | 2 ++
drivers/net/ethernet/intel/ice/ice_main.c | 16 ++++++++--------
3 files changed, 30 insertions(+), 9 deletions(-)
diff --git a/drivers/net/ethernet/intel/ice/ice_lib.c b/drivers/net/ethernet/intel/ice/ice_lib.c
index c9e0b533da47..af7574b0624b 100644
--- a/drivers/net/ethernet/intel/ice/ice_lib.c
+++ b/drivers/net/ethernet/intel/ice/ice_lib.c
@@ -6,6 +6,24 @@
#include "ice_lib.h"
#include "ice_dcb_lib.h"
+/**
+ * ice_vsi_type_str - maps VSI type enum to string equivalents
+ * @type: VSI type enum
+ */
+const char *ice_vsi_type_str(enum ice_vsi_type type)
+{
+ switch (type) {
+ case ICE_VSI_PF:
+ return "ICE_VSI_PF";
+ case ICE_VSI_VF:
+ return "ICE_VSI_VF";
+ case ICE_VSI_LB:
+ return "ICE_VSI_LB";
+ default:
+ return "unknown";
+ }
+}
+
/**
* ice_vsi_ctrl_rx_rings - Start or stop a VSI's Rx rings
* @vsi: the VSI being configured
@@ -700,7 +718,8 @@ static void ice_set_rss_vsi_ctx(struct ice_vsi_ctx *ctxt, struct ice_vsi *vsi)
hash_type = ICE_AQ_VSI_Q_OPT_RSS_TPLZ;
break;
case ICE_VSI_LB:
- dev_dbg(&pf->pdev->dev, "Unsupported VSI type %d\n", vsi->type);
+ dev_dbg(&pf->pdev->dev, "Unsupported VSI type %s\n",
+ ice_vsi_type_str(vsi->type));
return;
default:
dev_warn(&pf->pdev->dev, "Unknown VSI type %d\n", vsi->type);
diff --git a/drivers/net/ethernet/intel/ice/ice_lib.h b/drivers/net/ethernet/intel/ice/ice_lib.h
index 1ec2ad98ac46..364588dfc646 100644
--- a/drivers/net/ethernet/intel/ice/ice_lib.h
+++ b/drivers/net/ethernet/intel/ice/ice_lib.h
@@ -6,6 +6,8 @@
#include "ice.h"
+const char *ice_vsi_type_str(enum ice_vsi_type type);
+
int
ice_add_mac_to_list(struct ice_vsi *vsi, struct list_head *add_list,
const u8 *macaddr);
diff --git a/drivers/net/ethernet/intel/ice/ice_main.c b/drivers/net/ethernet/intel/ice/ice_main.c
index aaa398759548..ba9a0b74ef0d 100644
--- a/drivers/net/ethernet/intel/ice/ice_main.c
+++ b/drivers/net/ethernet/intel/ice/ice_main.c
@@ -4635,8 +4635,8 @@ static int ice_vsi_rebuild_by_type(struct ice_pf *pf, enum ice_vsi_type type)
err = ice_vsi_rebuild(vsi);
if (err) {
dev_err(&pf->pdev->dev,
- "rebuild VSI failed, err %d, VSI index %d, type %d\n",
- err, vsi->idx, type);
+ "rebuild VSI failed, err %d, VSI index %d, type %s\n",
+ err, vsi->idx, ice_vsi_type_str(type));
return err;
}
@@ -4644,8 +4644,8 @@ static int ice_vsi_rebuild_by_type(struct ice_pf *pf, enum ice_vsi_type type)
status = ice_replay_vsi(&pf->hw, vsi->idx);
if (status) {
dev_err(&pf->pdev->dev,
- "replay VSI failed, status %d, VSI index %d, type %d\n",
- status, vsi->idx, type);
+ "replay VSI failed, status %d, VSI index %d, type %s\n",
+ status, vsi->idx, ice_vsi_type_str(type));
return -EIO;
}
@@ -4658,13 +4658,13 @@ static int ice_vsi_rebuild_by_type(struct ice_pf *pf, enum ice_vsi_type type)
err = ice_ena_vsi(vsi, false);
if (err) {
dev_err(&pf->pdev->dev,
- "enable VSI failed, err %d, VSI index %d, type %d\n",
- err, vsi->idx, type);
+ "enable VSI failed, err %d, VSI index %d, type %s\n",
+ err, vsi->idx, ice_vsi_type_str(type));
return err;
}
- dev_info(&pf->pdev->dev, "VSI rebuilt. VSI index %d, type %d\n",
- vsi->idx, type);
+ dev_info(&pf->pdev->dev, "VSI rebuilt. VSI index %d, type %s\n",
+ vsi->idx, ice_vsi_type_str(type));
}
return 0;
--
2.20.1
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Intel-wired-lan] [PATCH S32 13/15] ice: Introduce and use ice_vsi_type_str
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 13/15] ice: Introduce and use ice_vsi_type_str Tony Nguyen
@ 2019-11-01 16:45 ` Bowers, AndrewX
0 siblings, 0 replies; 30+ messages in thread
From: Bowers, AndrewX @ 2019-11-01 16:45 UTC (permalink / raw)
To: intel-wired-lan
> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On
> Behalf Of Tony Nguyen
> Sent: Friday, October 25, 2019 7:35 AM
> To: intel-wired-lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [PATCH S32 13/15] ice: Introduce and use
> ice_vsi_type_str
>
> From: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
>
> ice_vsi_type_str converts an ice_vsi_type enum value to its string
> equivalent. This is expected to help easily identify VSI types from module
> print statements.
>
> Signed-off-by: Anirudh Venkataramanan
> <anirudh.venkataramanan@intel.com>
> ---
> drivers/net/ethernet/intel/ice/ice_lib.c | 21 ++++++++++++++++++++-
> drivers/net/ethernet/intel/ice/ice_lib.h | 2 ++
> drivers/net/ethernet/intel/ice/ice_main.c | 16 ++++++++--------
> 3 files changed, 30 insertions(+), 9 deletions(-)
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
^ permalink raw reply [flat|nested] 30+ messages in thread
* [Intel-wired-lan] [PATCH S32 14/15] ice: use more accurate ICE_DBG mask types
2019-10-25 14:34 [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and ice_dis_vsi in DCB configuration flow Tony Nguyen
` (11 preceding siblings ...)
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 13/15] ice: Introduce and use ice_vsi_type_str Tony Nguyen
@ 2019-10-25 14:34 ` Tony Nguyen
2019-11-01 16:45 ` Bowers, AndrewX
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 15/15] ice: print opcode when printing controlq errors Tony Nguyen
2019-11-01 16:41 ` [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and ice_dis_vsi in DCB configuration flow Bowers, AndrewX
14 siblings, 1 reply; 30+ messages in thread
From: Tony Nguyen @ 2019-10-25 14:34 UTC (permalink / raw)
To: intel-wired-lan
From: Jacob Keller <jacob.e.keller@intel.com>
ice_debug_cq is passed a mask which is always ICE_DBG_AQ_CMD. Modify this
function, removing the mask parameter entirely, and directly use the more
appropriate ICE_DBG_AQ_DESC and ICE_DBG_AQ_DESC_BUF.
The function is only called from ice_controlq.c, and has no
other callers outside of that file. Move it and mark it static to avoid
namespace pollution.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
---
drivers/net/ethernet/intel/ice/ice_common.c | 50 ----------------
drivers/net/ethernet/intel/ice/ice_common.h | 2 -
drivers/net/ethernet/intel/ice/ice_controlq.c | 57 +++++++++++++++++--
drivers/net/ethernet/intel/ice/ice_type.h | 2 +
4 files changed, 53 insertions(+), 58 deletions(-)
diff --git a/drivers/net/ethernet/intel/ice/ice_common.c b/drivers/net/ethernet/intel/ice/ice_common.c
index eb01c218c596..2c0dd2e2c232 100644
--- a/drivers/net/ethernet/intel/ice/ice_common.c
+++ b/drivers/net/ethernet/intel/ice/ice_common.c
@@ -1273,56 +1273,6 @@ const struct ice_ctx_ele ice_tlan_ctx_info[] = {
{ 0 }
};
-/**
- * ice_debug_cq
- * @hw: pointer to the hardware structure
- * @mask: debug mask
- * @desc: pointer to control queue descriptor
- * @buf: pointer to command buffer
- * @buf_len: max length of buf
- *
- * Dumps debug log about control command with descriptor contents.
- */
-void
-ice_debug_cq(struct ice_hw *hw, u32 __maybe_unused mask, void *desc, void *buf,
- u16 buf_len)
-{
- struct ice_aq_desc *cq_desc = (struct ice_aq_desc *)desc;
- u16 len;
-
-#ifndef CONFIG_DYNAMIC_DEBUG
- if (!(mask & hw->debug_mask))
- return;
-#endif
-
- if (!desc)
- return;
-
- len = le16_to_cpu(cq_desc->datalen);
-
- ice_debug(hw, mask,
- "CQ CMD: opcode 0x%04X, flags 0x%04X, datalen 0x%04X, retval 0x%04X\n",
- le16_to_cpu(cq_desc->opcode),
- le16_to_cpu(cq_desc->flags),
- le16_to_cpu(cq_desc->datalen), le16_to_cpu(cq_desc->retval));
- ice_debug(hw, mask, "\tcookie (h,l) 0x%08X 0x%08X\n",
- le32_to_cpu(cq_desc->cookie_high),
- le32_to_cpu(cq_desc->cookie_low));
- ice_debug(hw, mask, "\tparam (0,1) 0x%08X 0x%08X\n",
- le32_to_cpu(cq_desc->params.generic.param0),
- le32_to_cpu(cq_desc->params.generic.param1));
- ice_debug(hw, mask, "\taddr (h,l) 0x%08X 0x%08X\n",
- le32_to_cpu(cq_desc->params.generic.addr_high),
- le32_to_cpu(cq_desc->params.generic.addr_low));
- if (buf && cq_desc->datalen != 0) {
- ice_debug(hw, mask, "Buffer:\n");
- if (buf_len < len)
- len = buf_len;
-
- ice_debug_array(hw, mask, 16, 1, (u8 *)buf, len);
- }
-}
-
/* FW Admin Queue command wrappers */
/* Software lock/mutex that is meant to be held while the Global Config Lock
diff --git a/drivers/net/ethernet/intel/ice/ice_common.h b/drivers/net/ethernet/intel/ice/ice_common.h
index c17c5724d33b..63d7963221a0 100644
--- a/drivers/net/ethernet/intel/ice/ice_common.h
+++ b/drivers/net/ethernet/intel/ice/ice_common.h
@@ -20,8 +20,6 @@ enum ice_fw_modes {
enum ice_status ice_nvm_validate_checksum(struct ice_hw *hw);
-void
-ice_debug_cq(struct ice_hw *hw, u32 mask, void *desc, void *buf, u16 buf_len);
enum ice_status ice_init_hw(struct ice_hw *hw);
void ice_deinit_hw(struct ice_hw *hw);
enum ice_status
diff --git a/drivers/net/ethernet/intel/ice/ice_controlq.c b/drivers/net/ethernet/intel/ice/ice_controlq.c
index c68709c7ef81..947728aada46 100644
--- a/drivers/net/ethernet/intel/ice/ice_controlq.c
+++ b/drivers/net/ethernet/intel/ice/ice_controlq.c
@@ -809,6 +809,52 @@ static u16 ice_clean_sq(struct ice_hw *hw, struct ice_ctl_q_info *cq)
return ICE_CTL_Q_DESC_UNUSED(sq);
}
+/**
+ * ice_debug_cq
+ * @hw: pointer to the hardware structure
+ * @desc: pointer to control queue descriptor
+ * @buf: pointer to command buffer
+ * @buf_len: max length of buf
+ *
+ * Dumps debug log about control command with descriptor contents.
+ */
+static void ice_debug_cq(struct ice_hw *hw, void *desc, void *buf, u16 buf_len)
+{
+ struct ice_aq_desc *cq_desc = (struct ice_aq_desc *)desc;
+ u16 len;
+
+ if (!IS_ENABLED(CONFIG_DYNAMIC_DEBUG) &&
+ !((ICE_DBG_AQ_DESC | ICE_DBG_AQ_DESC_BUF) & hw->debug_mask))
+ return;
+
+ if (!desc)
+ return;
+
+ len = le16_to_cpu(cq_desc->datalen);
+
+ ice_debug(hw, ICE_DBG_AQ_DESC,
+ "CQ CMD: opcode 0x%04X, flags 0x%04X, datalen 0x%04X, retval 0x%04X\n",
+ le16_to_cpu(cq_desc->opcode),
+ le16_to_cpu(cq_desc->flags),
+ le16_to_cpu(cq_desc->datalen), le16_to_cpu(cq_desc->retval));
+ ice_debug(hw, ICE_DBG_AQ_DESC, "\tcookie (h,l) 0x%08X 0x%08X\n",
+ le32_to_cpu(cq_desc->cookie_high),
+ le32_to_cpu(cq_desc->cookie_low));
+ ice_debug(hw, ICE_DBG_AQ_DESC, "\tparam (0,1) 0x%08X 0x%08X\n",
+ le32_to_cpu(cq_desc->params.generic.param0),
+ le32_to_cpu(cq_desc->params.generic.param1));
+ ice_debug(hw, ICE_DBG_AQ_DESC, "\taddr (h,l) 0x%08X 0x%08X\n",
+ le32_to_cpu(cq_desc->params.generic.addr_high),
+ le32_to_cpu(cq_desc->params.generic.addr_low));
+ if (buf && cq_desc->datalen != 0) {
+ ice_debug(hw, ICE_DBG_AQ_DESC_BUF, "Buffer:\n");
+ if (buf_len < len)
+ len = buf_len;
+
+ ice_debug_array(hw, ICE_DBG_AQ_DESC_BUF, 16, 1, (u8 *)buf, len);
+ }
+}
+
/**
* ice_sq_done - check if FW has processed the Admin Send Queue (ATQ)
* @hw: pointer to the HW struct
@@ -934,10 +980,10 @@ ice_sq_send_cmd(struct ice_hw *hw, struct ice_ctl_q_info *cq,
}
/* Debug desc and buffer */
- ice_debug(hw, ICE_DBG_AQ_MSG,
+ ice_debug(hw, ICE_DBG_AQ_DESC,
"ATQ: Control Send queue desc and buffer:\n");
- ice_debug_cq(hw, ICE_DBG_AQ_CMD, (void *)desc_on_ring, buf, buf_size);
+ ice_debug_cq(hw, (void *)desc_on_ring, buf, buf_size);
(cq->sq.next_to_use)++;
if (cq->sq.next_to_use == cq->sq.count)
@@ -986,7 +1032,7 @@ ice_sq_send_cmd(struct ice_hw *hw, struct ice_ctl_q_info *cq,
ice_debug(hw, ICE_DBG_AQ_MSG,
"ATQ: desc and buffer writeback:\n");
- ice_debug_cq(hw, ICE_DBG_AQ_CMD, (void *)desc, buf, buf_size);
+ ice_debug_cq(hw, (void *)desc, buf, buf_size);
/* save writeback AQ if requested */
if (details->wb_desc)
@@ -1084,10 +1130,9 @@ ice_clean_rq_elem(struct ice_hw *hw, struct ice_ctl_q_info *cq,
if (e->msg_buf && e->msg_len)
memcpy(e->msg_buf, cq->rq.r.rq_bi[desc_idx].va, e->msg_len);
- ice_debug(hw, ICE_DBG_AQ_MSG, "ARQ: desc and buffer:\n");
+ ice_debug(hw, ICE_DBG_AQ_DESC, "ARQ: desc and buffer:\n");
- ice_debug_cq(hw, ICE_DBG_AQ_CMD, (void *)desc, e->msg_buf,
- cq->rq_buf_size);
+ ice_debug_cq(hw, (void *)desc, e->msg_buf, cq->rq_buf_size);
/* Restore the original datalen and buffer address in the desc,
* FW updates datalen to indicate the event message size
diff --git a/drivers/net/ethernet/intel/ice/ice_type.h b/drivers/net/ethernet/intel/ice/ice_type.h
index d3d7049c97f0..eba8b04b8cbd 100644
--- a/drivers/net/ethernet/intel/ice/ice_type.h
+++ b/drivers/net/ethernet/intel/ice/ice_type.h
@@ -46,6 +46,8 @@ static inline u32 ice_round_to_num(u32 N, u32 R)
#define ICE_DBG_PKG BIT_ULL(16)
#define ICE_DBG_RES BIT_ULL(17)
#define ICE_DBG_AQ_MSG BIT_ULL(24)
+#define ICE_DBG_AQ_DESC BIT_ULL(25)
+#define ICE_DBG_AQ_DESC_BUF BIT_ULL(26)
#define ICE_DBG_AQ_CMD BIT_ULL(27)
#define ICE_DBG_USER BIT_ULL(31)
--
2.20.1
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Intel-wired-lan] [PATCH S32 14/15] ice: use more accurate ICE_DBG mask types
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 14/15] ice: use more accurate ICE_DBG mask types Tony Nguyen
@ 2019-11-01 16:45 ` Bowers, AndrewX
0 siblings, 0 replies; 30+ messages in thread
From: Bowers, AndrewX @ 2019-11-01 16:45 UTC (permalink / raw)
To: intel-wired-lan
> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On
> Behalf Of Tony Nguyen
> Sent: Friday, October 25, 2019 7:35 AM
> To: intel-wired-lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [PATCH S32 14/15] ice: use more accurate ICE_DBG
> mask types
>
> From: Jacob Keller <jacob.e.keller@intel.com>
>
> ice_debug_cq is passed a mask which is always ICE_DBG_AQ_CMD. Modify
> this function, removing the mask parameter entirely, and directly use the
> more appropriate ICE_DBG_AQ_DESC and ICE_DBG_AQ_DESC_BUF.
>
> The function is only called from ice_controlq.c, and has no other callers
> outside of that file. Move it and mark it static to avoid namespace pollution.
>
> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
> ---
> drivers/net/ethernet/intel/ice/ice_common.c | 50 ----------------
> drivers/net/ethernet/intel/ice/ice_common.h | 2 -
> drivers/net/ethernet/intel/ice/ice_controlq.c | 57 +++++++++++++++++--
> drivers/net/ethernet/intel/ice/ice_type.h | 2 +
> 4 files changed, 53 insertions(+), 58 deletions(-)
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
^ permalink raw reply [flat|nested] 30+ messages in thread
* [Intel-wired-lan] [PATCH S32 15/15] ice: print opcode when printing controlq errors
2019-10-25 14:34 [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and ice_dis_vsi in DCB configuration flow Tony Nguyen
` (12 preceding siblings ...)
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 14/15] ice: use more accurate ICE_DBG mask types Tony Nguyen
@ 2019-10-25 14:34 ` Tony Nguyen
2019-11-01 16:45 ` Bowers, AndrewX
2019-11-01 16:41 ` [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and ice_dis_vsi in DCB configuration flow Bowers, AndrewX
14 siblings, 1 reply; 30+ messages in thread
From: Tony Nguyen @ 2019-10-25 14:34 UTC (permalink / raw)
To: intel-wired-lan
From: Jacob Keller <jacob.e.keller@intel.com>
To help aid in debugging, display the command opcode in debug messages
that print an error code. This makes it easier to see what command
failed if only ICE_DBG_AQ_MSG is enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
---
drivers/net/ethernet/intel/ice/ice_controlq.c | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/intel/ice/ice_controlq.c b/drivers/net/ethernet/intel/ice/ice_controlq.c
index 947728aada46..dd946866d7b8 100644
--- a/drivers/net/ethernet/intel/ice/ice_controlq.c
+++ b/drivers/net/ethernet/intel/ice/ice_controlq.c
@@ -1017,7 +1017,8 @@ ice_sq_send_cmd(struct ice_hw *hw, struct ice_ctl_q_info *cq,
retval = le16_to_cpu(desc->retval);
if (retval) {
ice_debug(hw, ICE_DBG_AQ_MSG,
- "Control Send Queue command completed with error 0x%x\n",
+ "Control Send Queue command 0x%04X completed with error 0x%X\n",
+ le16_to_cpu(desc->opcode),
retval);
/* strip off FW internal code */
@@ -1121,7 +1122,8 @@ ice_clean_rq_elem(struct ice_hw *hw, struct ice_ctl_q_info *cq,
if (flags & ICE_AQ_FLAG_ERR) {
ret_code = ICE_ERR_AQ_ERROR;
ice_debug(hw, ICE_DBG_AQ_MSG,
- "Control Receive Queue Event received with error 0x%x\n",
+ "Control Receive Queue Event 0x%04X received with error 0x%X\n",
+ le16_to_cpu(desc->opcode),
cq->rq_last_status);
}
memcpy(&e->desc, desc, sizeof(e->desc));
--
2.20.1
^ permalink raw reply related [flat|nested] 30+ messages in thread* [Intel-wired-lan] [PATCH S32 15/15] ice: print opcode when printing controlq errors
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 15/15] ice: print opcode when printing controlq errors Tony Nguyen
@ 2019-11-01 16:45 ` Bowers, AndrewX
0 siblings, 0 replies; 30+ messages in thread
From: Bowers, AndrewX @ 2019-11-01 16:45 UTC (permalink / raw)
To: intel-wired-lan
> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On
> Behalf Of Tony Nguyen
> Sent: Friday, October 25, 2019 7:35 AM
> To: intel-wired-lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [PATCH S32 15/15] ice: print opcode when printing
> controlq errors
>
> From: Jacob Keller <jacob.e.keller@intel.com>
>
> To help aid in debugging, display the command opcode in debug messages
> that print an error code. This makes it easier to see what command failed if
> only ICE_DBG_AQ_MSG is enabled.
>
> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
> ---
> drivers/net/ethernet/intel/ice/ice_controlq.c | 6 ++++--
> 1 file changed, 4 insertions(+), 2 deletions(-)
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
^ permalink raw reply [flat|nested] 30+ messages in thread
* [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and ice_dis_vsi in DCB configuration flow
2019-10-25 14:34 [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and ice_dis_vsi in DCB configuration flow Tony Nguyen
` (13 preceding siblings ...)
2019-10-25 14:34 ` [Intel-wired-lan] [PATCH S32 15/15] ice: print opcode when printing controlq errors Tony Nguyen
@ 2019-11-01 16:41 ` Bowers, AndrewX
14 siblings, 0 replies; 30+ messages in thread
From: Bowers, AndrewX @ 2019-11-01 16:41 UTC (permalink / raw)
To: intel-wired-lan
> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On
> Behalf Of Tony Nguyen
> Sent: Friday, October 25, 2019 7:34 AM
> To: intel-wired-lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [PATCH S32 01/15] ice: Use ice_ena_vsi and
> ice_dis_vsi in DCB configuration flow
>
> From: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
>
> DCB configuration flow needs to disable and enable only the PF (main) VSI,
> so use ice_ena_vsi and ice_dis_vsi. To avoid the use of ifdef to control the
> staticness of these functions, move them to ice_lib.c.
>
> Also change devm* to kzalloc/kfree in ice_pf_dcb_cfg()
>
> Signed-off-by: Anirudh Venkataramanan
> <anirudh.venkataramanan@intel.com>
> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
> ---
> drivers/net/ethernet/intel/ice/ice.h | 4 -
> drivers/net/ethernet/intel/ice/ice_dcb_lib.c | 28 +++++--
> drivers/net/ethernet/intel/ice/ice_lib.c | 56 ++++++++++++++
> drivers/net/ethernet/intel/ice/ice_lib.h | 4 +
> drivers/net/ethernet/intel/ice/ice_main.c | 79 --------------------
> 5 files changed, 82 insertions(+), 89 deletions(-)
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
^ permalink raw reply [flat|nested] 30+ messages in thread