From: Sasha Levin <sashal@kernel.org>
To: patches@lists.linux.dev, stable@vger.kernel.org
Cc: Mihai Sain <mihai.sain@microchip.com>,
Claudiu Beznea <claudiu.beznea@tuxon.dev>,
Sasha Levin <sashal@kernel.org>,
nicolas.ferre@microchip.com, alexandre.belloni@bootlin.com,
robh@kernel.org, krzk+dt@kernel.org, conor+dt@kernel.org,
varshini.rajendran@microchip.com,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [PATCH AUTOSEL 6.18] ARM: dts: microchip: sam9x7: fix gpio-lines count for pioB
Date: Mon, 20 Apr 2026 09:18:11 -0400 [thread overview]
Message-ID: <20260420132314.1023554-97-sashal@kernel.org> (raw)
In-Reply-To: <20260420132314.1023554-1-sashal@kernel.org>
From: Mihai Sain <mihai.sain@microchip.com>
[ Upstream commit 907150bbe566e23714a25d7bcb910f236c3c44c0 ]
The pioB controller on the SAM9X7 SoC actually supports 27 GPIO lines.
The previous value of 26 was incorrect, leading to the last pin being
unavailable for use by the GPIO subsystem.
Update the #gpio-lines property to reflect
the correct hardware specification.
Fixes: 41af45af8bc3 ("ARM: dts: at91: sam9x7: add device tree for SoC")
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Link: https://lore.kernel.org/r/20260209090735.2016-1-mihai.sain@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
LLM Generated explanations, may be completely bogus:
Error: Failed to generate final synthesis
arch/arm/boot/dts/microchip/sam9x7.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/microchip/sam9x7.dtsi b/arch/arm/boot/dts/microchip/sam9x7.dtsi
index 46dacbbd201dd..d242d7a934d0f 100644
--- a/arch/arm/boot/dts/microchip/sam9x7.dtsi
+++ b/arch/arm/boot/dts/microchip/sam9x7.dtsi
@@ -1226,7 +1226,7 @@ pioB: gpio@fffff600 {
interrupt-controller;
#gpio-cells = <2>;
gpio-controller;
- #gpio-lines = <26>;
+ #gpio-lines = <27>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 3>;
};
--
2.53.0
next prev parent reply other threads:[~2026-04-20 13:26 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20260420132314.1023554-1-sashal@kernel.org>
2026-04-20 13:17 ` [PATCH AUTOSEL 7.0-5.10] clk: spear: fix resource leak in clk_register_vco_pll() Sasha Levin
2026-04-20 13:17 ` [PATCH AUTOSEL 7.0-5.10] ARM: xen: validate hypervisor compatible before parsing its version Sasha Levin
2026-04-20 13:17 ` [PATCH AUTOSEL 7.0-6.19] wifi: mt76: avoid to set ACK for MCU command if wait_resp is not set Sasha Levin
2026-04-20 13:17 ` [PATCH AUTOSEL 7.0-6.18] phy: phy-mtk-tphy: Update names and format of kernel-doc comments Sasha Levin
2026-04-20 13:18 ` Sasha Levin [this message]
2026-04-20 13:18 ` [PATCH AUTOSEL 7.0-6.18] drm/imx: parallel-display: add DRM_DISPLAY_HELPER for DRM_IMX_PARALLEL_DISPLAY Sasha Levin
2026-04-20 13:18 ` [PATCH AUTOSEL 7.0-6.1] ASoC: mxs-sgtl5000: disable MCLK on error paths of mxs_sgtl5000_probe() Sasha Levin
2026-04-20 13:18 ` [PATCH AUTOSEL 7.0-6.12] Bluetooth: btmtk: add MT7902 MCU support Sasha Levin
2026-04-20 13:18 ` [PATCH AUTOSEL 7.0-6.18] wifi: mt76: flush pending TX before channel switch Sasha Levin
2026-04-20 13:18 ` [PATCH AUTOSEL 7.0-6.6] wifi: mt76: fix list corruption in mt76_wcid_cleanup Sasha Levin
2026-04-20 13:18 ` [PATCH AUTOSEL 7.0-6.12] wifi: mt76: add missing lock protection in mt76_sta_state for sta_event callback Sasha Levin
2026-04-20 13:18 ` [PATCH AUTOSEL 7.0-6.1] Bluetooth: btmtk: improve mt79xx firmware setup retry flow Sasha Levin
2026-04-20 13:19 ` [PATCH AUTOSEL 7.0-6.18] wifi: mt76: mt7996: Disable Rx hdr_trans in monitor mode Sasha Levin
2026-04-20 13:19 ` [PATCH AUTOSEL 7.0-6.12] drivers/virt: pkvm: Add Kconfig dependency on DMA_RESTRICTED_POOL Sasha Levin
2026-04-20 13:19 ` [PATCH AUTOSEL 7.0-6.12] wifi: mt76: mt7925: Skip scan process during suspend Sasha Levin
2026-04-20 13:19 ` [PATCH AUTOSEL 7.0-5.10] wifi: mt76: mt76x02: wake queues after reconfig Sasha Levin
2026-04-20 13:19 ` [PATCH AUTOSEL 7.0-6.12] wifi: mt76: mt7925: resolve link after acquiring mt76 mutex Sasha Levin
2026-04-20 13:19 ` [PATCH AUTOSEL 7.0-6.18] wifi: mt76: mt7996: fix queue pause after scan due to wrong channel switch reason Sasha Levin
2026-04-20 13:19 ` [PATCH AUTOSEL 6.18] ASoC: stm32_sai: fix incorrect BCLK polarity for DSP_A/B, LEFT_J Sasha Levin
2026-04-20 13:20 ` [PATCH AUTOSEL 7.0-6.12] net: ethernet: mtk_eth_soc: avoid writing to ESW registers on MT7628 Sasha Levin
2026-04-20 13:20 ` [PATCH AUTOSEL 6.18] media: rkvdec: reduce stack usage in rkvdec_init_v4l2_vp9_count_tbl() Sasha Levin
2026-04-20 13:20 ` [PATCH AUTOSEL 6.18] soc: aspeed: socinfo: Mask table entries for accurate SoC ID matching Sasha Levin
2026-04-20 13:20 ` [PATCH AUTOSEL 6.18] arm64: dts: imx93-9x9-qsb: change usdhc tuning step for eMMC and SD Sasha Levin
2026-04-20 13:20 ` [PATCH AUTOSEL 7.0-6.6] wifi: mt76: mt7996: reset device after MCU message timeout Sasha Levin
2026-04-20 13:20 ` [PATCH AUTOSEL 7.0] spi: stm32: fix rx DMA request error handling Sasha Levin
2026-04-20 13:21 ` [PATCH AUTOSEL 7.0-5.10] drm/mediatek: mtk_dsi: enable hs clock during pre-enable Sasha Levin
2026-04-20 13:21 ` [PATCH AUTOSEL 7.0-6.18] wifi: mt76: mt7996: fix frequency separation for station STR mode Sasha Levin
2026-04-20 13:21 ` [PATCH AUTOSEL 6.18] arm64: dts: imx8mq: Set the correct gpu_ahb clock frequency Sasha Levin
2026-04-20 13:22 ` [PATCH AUTOSEL 6.18] net: airoha: Fix memory leak in airoha_qdma_rx_process() Sasha Levin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260420132314.1023554-97-sashal@kernel.org \
--to=sashal@kernel.org \
--cc=alexandre.belloni@bootlin.com \
--cc=claudiu.beznea@tuxon.dev \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mihai.sain@microchip.com \
--cc=nicolas.ferre@microchip.com \
--cc=patches@lists.linux.dev \
--cc=robh@kernel.org \
--cc=stable@vger.kernel.org \
--cc=varshini.rajendran@microchip.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox