From: Joey Lu <a0987203069@gmail.com>
To: zhengxingda@iscas.ac.cn, maarten.lankhorst@linux.intel.com,
mripard@kernel.org, tzimmermann@suse.de, airlied@gmail.com,
simona@ffwll.ch, robh@kernel.org, krzk+dt@kernel.org,
conor+dt@kernel.org
Cc: ychuang3@nuvoton.com, schung@nuvoton.com, yclu4@nuvoton.com,
dri-devel@lists.freedesktop.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, Joey Lu <a0987203069@gmail.com>
Subject: [PATCH v4 4/6] drm/verisilicon: add DC8000 (DCUltraLite) display controller support
Date: Mon, 15 Jun 2026 14:50:01 +0800 [thread overview]
Message-ID: <20260615065003.76661-5-a0987203069@gmail.com> (raw)
In-Reply-To: <20260615065003.76661-1-a0987203069@gmail.com>
The Nuvoton MA35D1 SoC integrates a Verisilicon DCUltraLite display
controller whose register layout differs from the DC8200 in several
important ways:
1. No CONFIG_EX commit path: framebuffer updates use the enable (bit 0)
and reset (bit 4) bits in FB_CONFIG instead of the DC8200 staging
registers (FB_CONFIG_EX, FB_TOP_LEFT, FB_BOTTOM_RIGHT,
FB_BLEND_CONFIG, PANEL_CONFIG_EX).
2. No PANEL_START register: panel output starts when
PANEL_CONFIG.RUNNING is set; there is no multi-display sync start
register.
3. Different IRQ registers: DCUltraLite uses DISP_IRQ_STA (0x147C) /
DISP_IRQ_EN (0x1480) versus DC8200's TOP_IRQ_ACK (0x0010) /
TOP_IRQ_EN (0x0014).
4. Per-frame commit cycle: DCUltraLite requires the VALID bit in
FB_CONFIG to be set at the start of each atomic commit (crtc_begin)
and cleared after (crtc_flush).
5. Simpler clock topology: only 'core' (bus gate) and 'pix0' (pixel
divider) clocks; no axi or ahb clocks required. Make axi_clk and
ahb_clk optional (devm_clk_get_optional_enabled) so DC8000 nodes
without those clocks are handled gracefully.
Add vs_dc8000.c implementing the vs_dc_funcs vtable for the above
differences. The probe now selects vs_dc8000_funcs when the identified
generation is VSDC_GEN_DC8000 (DCUltraLite reads model 0x0,
revision 0x5560, customer_id 0x305).
Signed-off-by: Joey Lu <a0987203069@gmail.com>
---
drivers/gpu/drm/verisilicon/Makefile | 2 +-
drivers/gpu/drm/verisilicon/vs_dc.c | 9 ++-
drivers/gpu/drm/verisilicon/vs_dc.h | 1 +
drivers/gpu/drm/verisilicon/vs_dc8000.c | 78 +++++++++++++++++++++++++
4 files changed, 86 insertions(+), 4 deletions(-)
create mode 100644 drivers/gpu/drm/verisilicon/vs_dc8000.c
diff --git a/drivers/gpu/drm/verisilicon/Makefile b/drivers/gpu/drm/verisilicon/Makefile
index 9d4cd16452fa..d2fd8e4dff24 100644
--- a/drivers/gpu/drm/verisilicon/Makefile
+++ b/drivers/gpu/drm/verisilicon/Makefile
@@ -1,6 +1,6 @@
# SPDX-License-Identifier: GPL-2.0-only
-verisilicon-dc-objs := vs_bridge.o vs_crtc.o vs_dc.o vs_dc8200.o vs_drm.o vs_hwdb.o \
+verisilicon-dc-objs := vs_bridge.o vs_crtc.o vs_dc.o vs_dc8200.o vs_dc8000.o vs_drm.o vs_hwdb.o \
vs_plane.o vs_primary_plane.o vs_cursor_plane.o
obj-$(CONFIG_DRM_VERISILICON_DC) += verisilicon-dc.o
diff --git a/drivers/gpu/drm/verisilicon/vs_dc.c b/drivers/gpu/drm/verisilicon/vs_dc.c
index 9729b693d360..9499fffbca58 100644
--- a/drivers/gpu/drm/verisilicon/vs_dc.c
+++ b/drivers/gpu/drm/verisilicon/vs_dc.c
@@ -90,13 +90,13 @@ static int vs_dc_probe(struct platform_device *pdev)
return PTR_ERR(dc->core_clk);
}
- dc->axi_clk = devm_clk_get_enabled(dev, "axi");
+ dc->axi_clk = devm_clk_get_optional_enabled(dev, "axi");
if (IS_ERR(dc->axi_clk)) {
dev_err(dev, "can't get axi clock\n");
return PTR_ERR(dc->axi_clk);
}
- dc->ahb_clk = devm_clk_get_enabled(dev, "ahb");
+ dc->ahb_clk = devm_clk_get_optional_enabled(dev, "ahb");
if (IS_ERR(dc->ahb_clk)) {
dev_err(dev, "can't get ahb clock\n");
return PTR_ERR(dc->ahb_clk);
@@ -134,7 +134,10 @@ static int vs_dc_probe(struct platform_device *pdev)
dev_info(dev, "Found DC%x rev %x customer %x\n", dc->identity.model,
dc->identity.revision, dc->identity.customer_id);
- dc->funcs = &vs_dc8200_funcs;
+ if (dc->identity.generation == VSDC_GEN_DC8200)
+ dc->funcs = &vs_dc8200_funcs;
+ else
+ dc->funcs = &vs_dc8000_funcs;
if (port_count > dc->identity.display_count) {
dev_err(dev, "too many downstream ports than HW capability\n");
diff --git a/drivers/gpu/drm/verisilicon/vs_dc.h b/drivers/gpu/drm/verisilicon/vs_dc.h
index 544e1a37065b..5218e8cf63e2 100644
--- a/drivers/gpu/drm/verisilicon/vs_dc.h
+++ b/drivers/gpu/drm/verisilicon/vs_dc.h
@@ -66,5 +66,6 @@ struct vs_dc {
};
extern const struct vs_dc_funcs vs_dc8200_funcs;
+extern const struct vs_dc_funcs vs_dc8000_funcs;
#endif /* _VS_DC_H_ */
diff --git a/drivers/gpu/drm/verisilicon/vs_dc8000.c b/drivers/gpu/drm/verisilicon/vs_dc8000.c
new file mode 100644
index 000000000000..be0c0d7baf52
--- /dev/null
+++ b/drivers/gpu/drm/verisilicon/vs_dc8000.c
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2026 Joey Lu <yclu4@nuvoton.com>
+ */
+
+#include <linux/regmap.h>
+
+#include "vs_crtc_regs.h"
+#include "vs_dc.h"
+#include "vs_primary_plane_regs.h"
+
+static void vs_dc8000_panel_enable_ex(struct vs_dc *dc, unsigned int output)
+{
+ regmap_set_bits(dc->regs, VSDC_FB_CONFIG(output),
+ VSDC_FB_CONFIG_RESET);
+}
+
+static void vs_dc8000_panel_disable_ex(struct vs_dc *dc, unsigned int output)
+{
+ regmap_clear_bits(dc->regs, VSDC_FB_CONFIG(output),
+ VSDC_FB_CONFIG_RESET);
+}
+
+static void vs_dc8000_crtc_begin(struct vs_dc *dc, unsigned int output)
+{
+ regmap_set_bits(dc->regs, VSDC_FB_CONFIG(output),
+ VSDC_FB_CONFIG_VALID);
+}
+
+static void vs_dc8000_crtc_flush(struct vs_dc *dc, unsigned int output)
+{
+ regmap_clear_bits(dc->regs, VSDC_FB_CONFIG(output),
+ VSDC_FB_CONFIG_VALID);
+}
+
+static void vs_dc8000_crtc_enable(struct vs_dc *dc, unsigned int output)
+{
+ regmap_set_bits(dc->regs, VSDC_FB_CONFIG(output),
+ VSDC_FB_CONFIG_ENABLE);
+}
+
+static void vs_dc8000_crtc_disable(struct vs_dc *dc, unsigned int output)
+{
+ regmap_clear_bits(dc->regs, VSDC_FB_CONFIG(output),
+ VSDC_FB_CONFIG_ENABLE);
+}
+
+static void vs_dc8000_enable_vblank(struct vs_dc *dc, unsigned int output)
+{
+ regmap_set_bits(dc->regs, VSDC_DISP_IRQ_EN,
+ VSDC_DISP_IRQ_VSYNC(output));
+}
+
+static void vs_dc8000_disable_vblank(struct vs_dc *dc, unsigned int output)
+{
+ regmap_clear_bits(dc->regs, VSDC_DISP_IRQ_EN,
+ VSDC_DISP_IRQ_VSYNC(output));
+}
+
+static u32 vs_dc8000_irq_ack(struct vs_dc *dc)
+{
+ u32 irqs;
+
+ regmap_read(dc->regs, VSDC_DISP_IRQ_STA, &irqs);
+ return irqs;
+}
+
+const struct vs_dc_funcs vs_dc8000_funcs = {
+ .panel_enable_ex = vs_dc8000_panel_enable_ex,
+ .panel_disable_ex = vs_dc8000_panel_disable_ex,
+ .crtc_begin = vs_dc8000_crtc_begin,
+ .crtc_flush = vs_dc8000_crtc_flush,
+ .crtc_enable = vs_dc8000_crtc_enable,
+ .crtc_disable = vs_dc8000_crtc_disable,
+ .enable_vblank = vs_dc8000_enable_vblank,
+ .disable_vblank = vs_dc8000_disable_vblank,
+ .irq_ack = vs_dc8000_irq_ack,
+};
--
2.43.0
next prev parent reply other threads:[~2026-06-15 6:50 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-06-15 6:49 [PATCH v4 0/6] drm/verisilicon: add Nuvoton MA35D1 DCU Lite support Joey Lu
2026-06-15 6:49 ` [PATCH v4 1/6] dt-bindings: display: verisilicon,dc: generalize for single-output variants Joey Lu
2026-06-15 8:19 ` [PATCH v4 1/6] dt-bindings: display: verisilicon, dc: " Icenowy Zheng
2026-06-15 6:49 ` [PATCH v4 2/6] drm/verisilicon: add register-level macros for DC8000 Joey Lu
2026-06-15 8:24 ` Icenowy Zheng
2026-06-15 6:50 ` [PATCH v4 3/6] drm/verisilicon: introduce per-variant hardware ops table Joey Lu
2026-06-15 8:37 ` Icenowy Zheng
2026-06-15 6:50 ` Joey Lu [this message]
2026-06-15 8:51 ` [PATCH v4 4/6] drm/verisilicon: add DC8000 (DCUltraLite) display controller support Icenowy Zheng
2026-06-15 6:50 ` [PATCH v4 5/6] drm/verisilicon: add DCUltraLite chip identity to HWDB Joey Lu
2026-06-15 8:57 ` Icenowy Zheng
2026-06-15 6:50 ` [PATCH v4 6/6] drm/verisilicon: extend Kconfig to support ARCH_MA35 platforms Joey Lu
2026-06-15 8:58 ` Icenowy Zheng
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260615065003.76661-5-a0987203069@gmail.com \
--to=a0987203069@gmail.com \
--cc=airlied@gmail.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=maarten.lankhorst@linux.intel.com \
--cc=mripard@kernel.org \
--cc=robh@kernel.org \
--cc=schung@nuvoton.com \
--cc=simona@ffwll.ch \
--cc=tzimmermann@suse.de \
--cc=ychuang3@nuvoton.com \
--cc=yclu4@nuvoton.com \
--cc=zhengxingda@iscas.ac.cn \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox