[PATCH v3 0/7] mmc: sdhci-esdhc-imx: fix SDIO suspend/resume issues

[PATCH v3 0/7] mmc: sdhci-esdhc-imx: fix SDIO suspend/resume issues

[ziniu.wang_1]

From: Luke Wang <ziniu.wang_1@nxp.com>

This series fixes several suspend/resume issues in the sdhci-esdhc-imx
driver, primarily affecting SDIO devices (e.g., WiFi).

Issues fixed:
- Tuning delay values not saved/restored for out-of-band wakeup devices
- DLL override lost after resume for DDR modes
- Pinctrl not restored before DDR_EN is set, causing CRC errors
- Unhandled interrupt during resume causing "nobody cared" warning
- Various error handling issues in suspend/resume paths

Changes since v2:
- Patch 3: Updated commit message to explain the SoC IP integration
  detail about internal loopback path change when switching pinctrl
  from GPIO to USDHC function (per Bough Chen suggestion)
- Patch 5 (v2): Split into three separate patches (5/6/7) so each
  patch fixes one problem (per Frank Li suggestion)

Luke Wang (7):
  mmc: sdhci-esdhc-imx: remove unnecessary mmc_card_wake_sdio_irq check
    for tuning save/restore
  mmc: sdhci-esdhc-imx: restore DLL override for DDR modes on resume
  mmc: sdhci-esdhc-imx: restore pinctrl before restoring ios timing on
    resume
  mmc: sdhci-esdhc-imx: disable irq during suspend to fix unhandled
    interrupt
  mmc: sdhci-esdhc-imx: use pm_runtime_resume_and_get() in suspend
  mmc: sdhci-esdhc-imx: make non-fatal errors non-blocking in suspend
  mmc: sdhci-esdhc-imx: fix resume error handling

 drivers/mmc/host/sdhci-esdhc-imx.c | 75 ++++++++++++++++++++----------
 1 file changed, 51 insertions(+), 24 deletions(-)

-- 
2.34.1

[PATCH v3 1/7] mmc: sdhci-esdhc-imx: remove unnecessary mmc_card_wake_sdio_irq check for tuning save/restore

[ziniu.wang_1]

From: Luke Wang <ziniu.wang_1@nxp.com>

The tuning save/restore during system PM is conditioned on
mmc_card_wake_sdio_irq(), but this check is unrelated to whether
tuning values need to be preserved. The actual requirement is that
the card keeps power during suspend and the controller is a uSDHC.

SDIO devices using out-of-band GPIO wakeup maintain power during
suspend but do not set the SDIO IRQ wake flag. In this case the
tuning delay values are not saved/restored.

Remove the unnecessary mmc_card_wake_sdio_irq() condition from both
the suspend save and resume restore paths.

Fixes: c63d25cdc59a ("mmc: sdhci-esdhc-imx: Save tuning value when card stays powered in suspend")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
---
 drivers/mmc/host/sdhci-esdhc-imx.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index 18ecddd6df6f..6526d65538de 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -2064,8 +2064,7 @@ static int sdhci_esdhc_suspend(struct device *dev)
 	 * to save the tuning delay value just in case the usdhc
 	 * lost power during system PM.
 	 */
-	if (mmc_card_keep_power(host->mmc) && mmc_card_wake_sdio_irq(host->mmc) &&
-	    esdhc_is_usdhc(imx_data))
+	if (mmc_card_keep_power(host->mmc) && esdhc_is_usdhc(imx_data))
 		sdhc_esdhc_tuning_save(host);
 
 	if (device_may_wakeup(dev)) {
@@ -2124,8 +2123,7 @@ static int sdhci_esdhc_resume(struct device *dev)
 	 * restore the saved tuning delay value for the device which keep
 	 * power during system PM.
 	 */
-	if (mmc_card_keep_power(host->mmc) && mmc_card_wake_sdio_irq(host->mmc) &&
-	    esdhc_is_usdhc(imx_data))
+	if (mmc_card_keep_power(host->mmc) && esdhc_is_usdhc(imx_data))
 		sdhc_esdhc_tuning_restore(host);
 
 	pm_runtime_put_autosuspend(dev);
-- 
2.34.1

[PATCH v3 2/7] mmc: sdhci-esdhc-imx: restore DLL override for DDR modes on resume

[ziniu.wang_1]

From: Luke Wang <ziniu.wang_1@nxp.com>

sdhci_esdhc_imx_hwinit() unconditionally clears ESDHC_DLL_CTRL by
writing zero. For SDIO devices that keep power during system suspend
and operate in DDR mode, the card remains in DDR timing while the host
DLL override configuration is lost.

Extract the DLL override setup from esdhc_set_uhs_signaling() into
a helper esdhc_set_dll_override(), and call it on the resume path
when the card kept power and is using a DDR timing mode.

Fixes: 676a83855614 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
---
 drivers/mmc/host/sdhci-esdhc-imx.c | 38 ++++++++++++++++++++++--------
 1 file changed, 28 insertions(+), 10 deletions(-)

diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index 6526d65538de..a944351dbcdf 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -1349,6 +1349,23 @@ static int esdhc_change_pinstate(struct sdhci_host *host,
 	return pinctrl_select_state(imx_data->pinctrl, pinctrl);
 }
 
+static void esdhc_set_dll_override(struct sdhci_host *host)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
+	struct esdhc_platform_data *boarddata = &imx_data->boarddata;
+	u32 v;
+
+	if (!boarddata->delay_line)
+		return;
+
+	v = boarddata->delay_line << ESDHC_DLL_OVERRIDE_VAL_SHIFT |
+	    (1 << ESDHC_DLL_OVERRIDE_EN_SHIFT);
+	if (is_imx53_esdhc(imx_data))
+		v <<= 1;
+	writel(v, host->ioaddr + ESDHC_DLL_CTRL);
+}
+
 /*
  * For HS400 eMMC, there is a data_strobe line. This signal is generated
  * by the device and used for data output and CRC status response output
@@ -1425,15 +1442,7 @@ static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
 		m |= ESDHC_MIX_CTRL_DDREN;
 		writel(m, host->ioaddr + ESDHC_MIX_CTRL);
 		imx_data->is_ddr = 1;
-		if (boarddata->delay_line) {
-			u32 v;
-			v = boarddata->delay_line <<
-				ESDHC_DLL_OVERRIDE_VAL_SHIFT |
-				(1 << ESDHC_DLL_OVERRIDE_EN_SHIFT);
-			if (is_imx53_esdhc(imx_data))
-				v <<= 1;
-			writel(v, host->ioaddr + ESDHC_DLL_CTRL);
-		}
+		esdhc_set_dll_override(host);
 		break;
 	case MMC_TIMING_MMC_HS400:
 		m |= ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN;
@@ -2123,9 +2132,18 @@ static int sdhci_esdhc_resume(struct device *dev)
 	 * restore the saved tuning delay value for the device which keep
 	 * power during system PM.
 	 */
-	if (mmc_card_keep_power(host->mmc) && esdhc_is_usdhc(imx_data))
+	if (mmc_card_keep_power(host->mmc) && esdhc_is_usdhc(imx_data)) {
 		sdhc_esdhc_tuning_restore(host);
 
+		/*
+		 * Restore DLL override for DDR modes. hwinit unconditionally
+		 * clears ESDHC_DLL_CTRL, but the card is still in DDR mode.
+		 */
+		if (host->timing == MMC_TIMING_UHS_DDR50 ||
+		    host->timing == MMC_TIMING_MMC_DDR52)
+			esdhc_set_dll_override(host);
+	}
+
 	pm_runtime_put_autosuspend(dev);
 
 	return ret;
-- 
2.34.1

[PATCH v3 3/7] mmc: sdhci-esdhc-imx: restore pinctrl before restoring ios timing on resume

[ziniu.wang_1]

From: Luke Wang <ziniu.wang_1@nxp.com>

SDIO devices such as WiFi may keep power during suspend, so the MMC
core skips full card re-initialization on resume and directly restores
the host controller's ios timing to match the card. For DDR mode,
pm_runtime_force_resume() sets DDR_EN before the pin configuration is
restored from sleep state.

This is related to the SoC IP integration: switching pinctrl setting
(changing alt from GPIO to USDHC) impacts the internal loopback path.
If pinctrl configures the pad to GPIO function, once DDR_EN is set, the
DLL delay will be fixed based on the GPIO function loopback path. When
the pinctrl is later changed to USDHC function, the internal loopback
path changes, making the original fixed sample point no longer suitable
for the current loopback path. This causes persistent read CRC errors on
subsequent data transfers.

SD/eMMC running in DDR mode are unaffected as they are fully
re-initialized from legacy timing after resume.

Fix this by restoring the pinctrl state based on current timing mode
using esdhc_change_pinstate() before pm_runtime_force_resume(). This
ensures the correct pin configuration (e.g., 100/200MHz for UHS modes)
is applied before DDR_EN is set. Only restore for non-wakeup devices
since wakeup devices kept their active pin state during suspend.

Fixes: 676a83855614 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
---
 drivers/mmc/host/sdhci-esdhc-imx.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index a944351dbcdf..7fcaecdd4ec6 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -2114,6 +2114,12 @@ static int sdhci_esdhc_resume(struct device *dev)
 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
 	int ret;
 
+	if (!device_may_wakeup(dev)) {
+		ret = esdhc_change_pinstate(host, host->timing);
+		if (ret)
+			dev_warn(dev, "Failed to restore pinctrl state\n");
+	}
+
 	pm_runtime_force_resume(dev);
 
 	ret = mmc_gpio_set_cd_wake(host->mmc, false);
-- 
2.34.1

[PATCH v3 4/7] mmc: sdhci-esdhc-imx: disable irq during suspend to fix unhandled interrupt

[ziniu.wang_1]

From: Luke Wang <ziniu.wang_1@nxp.com>

When using WIFI out-of-band wakeup, an "irq xxx: nobody cared" warning
occurs. This happens because the usdhc interrupt is not disabled during
system suspend when device_may_wakeup() returns false.

The sequence of events leading to this issue:
1. System enters suspend without disabling usdhc interrupt
(because device_may_wakeup() returns false for usdhc device)
2. WIFI out-of-band wakeup triggers system resume via GPIO interrupt
3. WIFI sends a Card interrupt before usdhc has fully resumed
4. usdhc is still in runtime suspend state and cannot handle the
interrupt properly
5. The unhandled interrupt triggers "nobody cared" warning

Fix this by unconditionally disabling the usdhc interrupt during suspend
and re-enabling it during resume, regardless of the wakeup capability.
This ensures no interrupts are processed during the suspend/resume
transition.

Fixes: 676a83855614 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
---
 drivers/mmc/host/sdhci-esdhc-imx.c | 11 ++++++-----
 1 file changed, 6 insertions(+), 5 deletions(-)

diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index 7fcaecdd4ec6..c4a22e42628e 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -2076,9 +2076,10 @@ static int sdhci_esdhc_suspend(struct device *dev)
 	if (mmc_card_keep_power(host->mmc) && esdhc_is_usdhc(imx_data))
 		sdhc_esdhc_tuning_save(host);
 
+	/* The irqs of imx are not shared. It is safe to disable */
+	disable_irq(host->irq);
+
 	if (device_may_wakeup(dev)) {
-		/* The irqs of imx are not shared. It is safe to disable */
-		disable_irq(host->irq);
 		ret = sdhci_enable_irq_wakeups(host);
 		if (!ret)
 			dev_warn(dev, "Failed to enable irq wakeup\n");
@@ -2129,10 +2130,10 @@ static int sdhci_esdhc_resume(struct device *dev)
 	/* re-initialize hw state in case it's lost in low power mode */
 	sdhci_esdhc_imx_hwinit(host);
 
-	if (host->irq_wake_enabled) {
+	if (host->irq_wake_enabled)
 		sdhci_disable_irq_wakeups(host);
-		enable_irq(host->irq);
-	}
+
+	enable_irq(host->irq);
 
 	/*
 	 * restore the saved tuning delay value for the device which keep
-- 
2.34.1

[PATCH v3 5/7] mmc: sdhci-esdhc-imx: use pm_runtime_resume_and_get() in suspend

[ziniu.wang_1]

From: Luke Wang <ziniu.wang_1@nxp.com>

Replace pm_runtime_get_sync() with pm_runtime_resume_and_get() to
simplify error handling. pm_runtime_resume_and_get() automatically
drops the usage counter on failure, avoiding the need for a separate
pm_runtime_put_noidle() call. If it fails, the device is unclocked and
accessing hardware registers would cause a kernel panic, so return the
error immediately.

Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
---
 drivers/mmc/host/sdhci-esdhc-imx.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index c4a22e42628e..97ee3f933bda 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -2060,7 +2060,9 @@ static int sdhci_esdhc_suspend(struct device *dev)
 	 * 2, make sure the pm_runtime_force_resume() in sdhci_esdhc_resume() really
 	 *    invoke its ->runtime_resume callback (needs_force_resume = 1).
 	 */
-	pm_runtime_get_sync(dev);
+	ret = pm_runtime_resume_and_get(dev);
+	if (ret)
+		return ret;
 
 	if ((imx_data->socdata->flags & ESDHC_FLAG_STATE_LOST_IN_LPMODE) &&
 		(host->tuning_mode != SDHCI_TUNING_MODE_1)) {
-- 
2.34.1

[PATCH v3 6/7] mmc: sdhci-esdhc-imx: make non-fatal errors non-blocking in suspend

[ziniu.wang_1]

From: Luke Wang <ziniu.wang_1@nxp.com>

Make pinctrl_pm_select_sleep_state() and mmc_gpio_set_cd_wake() failures
non-fatal in the suspend path. These failures only mean slightly higher
power consumption or missing CD wakeup capability, but should not block
system suspend.

Also change the function to always return 0 on the success path instead
of propagating non-fatal warning return values.

Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
---
 drivers/mmc/host/sdhci-esdhc-imx.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index 97ee3f933bda..abee3d7a07a3 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -2096,10 +2096,12 @@ static int sdhci_esdhc_suspend(struct device *dev)
 		 */
 		ret = pinctrl_pm_select_sleep_state(dev);
 		if (ret)
-			return ret;
+			dev_warn(dev, "Failed to select sleep pinctrl state\n");
 	}
 
 	ret = mmc_gpio_set_cd_wake(host->mmc, true);
+	if (ret)
+		dev_warn(dev, "Failed to enable cd wake\n");
 
 	/*
 	 * Make sure invoke runtime_suspend to gate off clock.
@@ -2107,7 +2109,7 @@ static int sdhci_esdhc_suspend(struct device *dev)
 	 */
 	pm_runtime_force_suspend(dev);
 
-	return ret;
+	return 0;
 }
 
 static int sdhci_esdhc_resume(struct device *dev)
-- 
2.34.1

[PATCH v3 7/7] mmc: sdhci-esdhc-imx: fix resume error handling

[ziniu.wang_1]

From: Luke Wang <ziniu.wang_1@nxp.com>

Check pm_runtime_force_resume() return value in resume. If it fails
(clock enable failure), return immediately since accessing hardware
registers on an unclocked device would cause a kernel panic.

Remove the return value check for mmc_gpio_set_cd_wake(host->mmc, false)
since disable_irq_wake() called internally always returns 0.

Also return 0 explicitly on the success path instead of propagating
stale return values.

Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
---
 drivers/mmc/host/sdhci-esdhc-imx.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index abee3d7a07a3..4d6818c95809 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -2125,12 +2125,12 @@ static int sdhci_esdhc_resume(struct device *dev)
 			dev_warn(dev, "Failed to restore pinctrl state\n");
 	}
 
-	pm_runtime_force_resume(dev);
-
-	ret = mmc_gpio_set_cd_wake(host->mmc, false);
+	ret = pm_runtime_force_resume(dev);
 	if (ret)
 		return ret;
 
+	mmc_gpio_set_cd_wake(host->mmc, false);
+
 	/* re-initialize hw state in case it's lost in low power mode */
 	sdhci_esdhc_imx_hwinit(host);
 
@@ -2157,7 +2157,7 @@ static int sdhci_esdhc_resume(struct device *dev)
 
 	pm_runtime_put_autosuspend(dev);
 
-	return ret;
+	return 0;
 }
 
 static int sdhci_esdhc_runtime_suspend(struct device *dev)
-- 
2.34.1

Re: [PATCH v3 1/7] mmc: sdhci-esdhc-imx: remove unnecessary mmc_card_wake_sdio_irq check for tuning save/restore

[Bough Chen]

On Mon, Jun 29, 2026 at 05:19:48PM +0800, ziniu.wang_1@oss.nxp.com wrote:
> From: Luke Wang <ziniu.wang_1@nxp.com>
> 
> The tuning save/restore during system PM is conditioned on
> mmc_card_wake_sdio_irq(), but this check is unrelated to whether
> tuning values need to be preserved. The actual requirement is that
> the card keeps power during suspend and the controller is a uSDHC.
> 
> SDIO devices using out-of-band GPIO wakeup maintain power during
> suspend but do not set the SDIO IRQ wake flag. In this case the
> tuning delay values are not saved/restored.
> 
> Remove the unnecessary mmc_card_wake_sdio_irq() condition from both
> the suspend save and resume restore paths.
> 
> Fixes: c63d25cdc59a ("mmc: sdhci-esdhc-imx: Save tuning value when card stays powered in suspend")
> Reviewed-by: Frank Li <Frank.Li@nxp.com>
> Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>

Reviewed-by: Haibo Chen <haibo.chen@nxp.com>

Regards
Haibo Chen
> ---
>  drivers/mmc/host/sdhci-esdhc-imx.c | 6 ++----
>  1 file changed, 2 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
> index 18ecddd6df6f..6526d65538de 100644
> --- a/drivers/mmc/host/sdhci-esdhc-imx.c
> +++ b/drivers/mmc/host/sdhci-esdhc-imx.c
> @@ -2064,8 +2064,7 @@ static int sdhci_esdhc_suspend(struct device *dev)
>  	 * to save the tuning delay value just in case the usdhc
>  	 * lost power during system PM.
>  	 */
> -	if (mmc_card_keep_power(host->mmc) && mmc_card_wake_sdio_irq(host->mmc) &&
> -	    esdhc_is_usdhc(imx_data))
> +	if (mmc_card_keep_power(host->mmc) && esdhc_is_usdhc(imx_data))
>  		sdhc_esdhc_tuning_save(host);
>  
>  	if (device_may_wakeup(dev)) {
> @@ -2124,8 +2123,7 @@ static int sdhci_esdhc_resume(struct device *dev)
>  	 * restore the saved tuning delay value for the device which keep
>  	 * power during system PM.
>  	 */
> -	if (mmc_card_keep_power(host->mmc) && mmc_card_wake_sdio_irq(host->mmc) &&
> -	    esdhc_is_usdhc(imx_data))
> +	if (mmc_card_keep_power(host->mmc) && esdhc_is_usdhc(imx_data))
>  		sdhc_esdhc_tuning_restore(host);
>  
>  	pm_runtime_put_autosuspend(dev);
> -- 
> 2.34.1
> 

Re: [PATCH v3 2/7] mmc: sdhci-esdhc-imx: restore DLL override for DDR modes on resume

[Bough Chen]

On Mon, Jun 29, 2026 at 05:19:49PM +0800, ziniu.wang_1@oss.nxp.com wrote:
> From: Luke Wang <ziniu.wang_1@nxp.com>
> 
> sdhci_esdhc_imx_hwinit() unconditionally clears ESDHC_DLL_CTRL by
> writing zero. For SDIO devices that keep power during system suspend
> and operate in DDR mode, the card remains in DDR timing while the host
> DLL override configuration is lost.
> 
> Extract the DLL override setup from esdhc_set_uhs_signaling() into
> a helper esdhc_set_dll_override(), and call it on the resume path
> when the card kept power and is using a DDR timing mode.
> 
> Fixes: 676a83855614 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
> Reviewed-by: Frank Li <Frank.Li@nxp.com>
> Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>

Reviewed-by: Haibo Chen <haibo.chen@nxp.com>

Regards
Haibo Chen
> ---
>  drivers/mmc/host/sdhci-esdhc-imx.c | 38 ++++++++++++++++++++++--------
>  1 file changed, 28 insertions(+), 10 deletions(-)
> 
> diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
> index 6526d65538de..a944351dbcdf 100644
> --- a/drivers/mmc/host/sdhci-esdhc-imx.c
> +++ b/drivers/mmc/host/sdhci-esdhc-imx.c
> @@ -1349,6 +1349,23 @@ static int esdhc_change_pinstate(struct sdhci_host *host,
>  	return pinctrl_select_state(imx_data->pinctrl, pinctrl);
>  }
>  
> +static void esdhc_set_dll_override(struct sdhci_host *host)
> +{
> +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> +	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
> +	struct esdhc_platform_data *boarddata = &imx_data->boarddata;
> +	u32 v;
> +
> +	if (!boarddata->delay_line)
> +		return;
> +
> +	v = boarddata->delay_line << ESDHC_DLL_OVERRIDE_VAL_SHIFT |
> +	    (1 << ESDHC_DLL_OVERRIDE_EN_SHIFT);
> +	if (is_imx53_esdhc(imx_data))
> +		v <<= 1;
> +	writel(v, host->ioaddr + ESDHC_DLL_CTRL);
> +}
> +
>  /*
>   * For HS400 eMMC, there is a data_strobe line. This signal is generated
>   * by the device and used for data output and CRC status response output
> @@ -1425,15 +1442,7 @@ static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
>  		m |= ESDHC_MIX_CTRL_DDREN;
>  		writel(m, host->ioaddr + ESDHC_MIX_CTRL);
>  		imx_data->is_ddr = 1;
> -		if (boarddata->delay_line) {
> -			u32 v;
> -			v = boarddata->delay_line <<
> -				ESDHC_DLL_OVERRIDE_VAL_SHIFT |
> -				(1 << ESDHC_DLL_OVERRIDE_EN_SHIFT);
> -			if (is_imx53_esdhc(imx_data))
> -				v <<= 1;
> -			writel(v, host->ioaddr + ESDHC_DLL_CTRL);
> -		}
> +		esdhc_set_dll_override(host);
>  		break;
>  	case MMC_TIMING_MMC_HS400:
>  		m |= ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN;
> @@ -2123,9 +2132,18 @@ static int sdhci_esdhc_resume(struct device *dev)
>  	 * restore the saved tuning delay value for the device which keep
>  	 * power during system PM.
>  	 */
> -	if (mmc_card_keep_power(host->mmc) && esdhc_is_usdhc(imx_data))
> +	if (mmc_card_keep_power(host->mmc) && esdhc_is_usdhc(imx_data)) {
>  		sdhc_esdhc_tuning_restore(host);
>  
> +		/*
> +		 * Restore DLL override for DDR modes. hwinit unconditionally
> +		 * clears ESDHC_DLL_CTRL, but the card is still in DDR mode.
> +		 */
> +		if (host->timing == MMC_TIMING_UHS_DDR50 ||
> +		    host->timing == MMC_TIMING_MMC_DDR52)
> +			esdhc_set_dll_override(host);
> +	}
> +
>  	pm_runtime_put_autosuspend(dev);
>  
>  	return ret;
> -- 
> 2.34.1
> 

Re: [PATCH v3 3/7] mmc: sdhci-esdhc-imx: restore pinctrl before restoring ios timing on resume

[Bough Chen]

On Mon, Jun 29, 2026 at 05:19:50PM +0800, ziniu.wang_1@oss.nxp.com wrote:
> From: Luke Wang <ziniu.wang_1@nxp.com>
> 
> SDIO devices such as WiFi may keep power during suspend, so the MMC
> core skips full card re-initialization on resume and directly restores
> the host controller's ios timing to match the card. For DDR mode,
> pm_runtime_force_resume() sets DDR_EN before the pin configuration is
> restored from sleep state.
> 
> This is related to the SoC IP integration: switching pinctrl setting
> (changing alt from GPIO to USDHC) impacts the internal loopback path.
> If pinctrl configures the pad to GPIO function, once DDR_EN is set, the
> DLL delay will be fixed based on the GPIO function loopback path. When
> the pinctrl is later changed to USDHC function, the internal loopback
> path changes, making the original fixed sample point no longer suitable
> for the current loopback path. This causes persistent read CRC errors on
> subsequent data transfers.
> 
> SD/eMMC running in DDR mode are unaffected as they are fully
> re-initialized from legacy timing after resume.
> 
> Fix this by restoring the pinctrl state based on current timing mode
> using esdhc_change_pinstate() before pm_runtime_force_resume(). This
> ensures the correct pin configuration (e.g., 100/200MHz for UHS modes)
> is applied before DDR_EN is set. Only restore for non-wakeup devices
> since wakeup devices kept their active pin state during suspend.
> 
> Fixes: 676a83855614 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
> Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>

Reviewed-by: Haibo Chen <haibo.chen@nxp.com>

Regards
Haibo Chen
> ---
>  drivers/mmc/host/sdhci-esdhc-imx.c | 6 ++++++
>  1 file changed, 6 insertions(+)
> 
> diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
> index a944351dbcdf..7fcaecdd4ec6 100644
> --- a/drivers/mmc/host/sdhci-esdhc-imx.c
> +++ b/drivers/mmc/host/sdhci-esdhc-imx.c
> @@ -2114,6 +2114,12 @@ static int sdhci_esdhc_resume(struct device *dev)
>  	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
>  	int ret;
>  
> +	if (!device_may_wakeup(dev)) {
> +		ret = esdhc_change_pinstate(host, host->timing);
> +		if (ret)
> +			dev_warn(dev, "Failed to restore pinctrl state\n");
> +	}
> +
>  	pm_runtime_force_resume(dev);
>  
>  	ret = mmc_gpio_set_cd_wake(host->mmc, false);
> -- 
> 2.34.1
> 

Re: [PATCH v3 4/7] mmc: sdhci-esdhc-imx: disable irq during suspend to fix unhandled interrupt

[Bough Chen]

On Mon, Jun 29, 2026 at 05:19:51PM +0800, ziniu.wang_1@oss.nxp.com wrote:
> From: Luke Wang <ziniu.wang_1@nxp.com>
> 
> When using WIFI out-of-band wakeup, an "irq xxx: nobody cared" warning
> occurs. This happens because the usdhc interrupt is not disabled during
> system suspend when device_may_wakeup() returns false.
> 
> The sequence of events leading to this issue:
> 1. System enters suspend without disabling usdhc interrupt
> (because device_may_wakeup() returns false for usdhc device)
> 2. WIFI out-of-band wakeup triggers system resume via GPIO interrupt
> 3. WIFI sends a Card interrupt before usdhc has fully resumed
> 4. usdhc is still in runtime suspend state and cannot handle the
> interrupt properly
> 5. The unhandled interrupt triggers "nobody cared" warning
> 
> Fix this by unconditionally disabling the usdhc interrupt during suspend
> and re-enabling it during resume, regardless of the wakeup capability.
> This ensures no interrupts are processed during the suspend/resume
> transition.
> 
> Fixes: 676a83855614 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
> Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>

Reviewed-by: Haibo Chen <haibo.chen@nxp.com>

Regards
Haibo Chen
> ---
>  drivers/mmc/host/sdhci-esdhc-imx.c | 11 ++++++-----
>  1 file changed, 6 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
> index 7fcaecdd4ec6..c4a22e42628e 100644
> --- a/drivers/mmc/host/sdhci-esdhc-imx.c
> +++ b/drivers/mmc/host/sdhci-esdhc-imx.c
> @@ -2076,9 +2076,10 @@ static int sdhci_esdhc_suspend(struct device *dev)
>  	if (mmc_card_keep_power(host->mmc) && esdhc_is_usdhc(imx_data))
>  		sdhc_esdhc_tuning_save(host);
>  
> +	/* The irqs of imx are not shared. It is safe to disable */
> +	disable_irq(host->irq);
> +
>  	if (device_may_wakeup(dev)) {
> -		/* The irqs of imx are not shared. It is safe to disable */
> -		disable_irq(host->irq);
>  		ret = sdhci_enable_irq_wakeups(host);
>  		if (!ret)
>  			dev_warn(dev, "Failed to enable irq wakeup\n");
> @@ -2129,10 +2130,10 @@ static int sdhci_esdhc_resume(struct device *dev)
>  	/* re-initialize hw state in case it's lost in low power mode */
>  	sdhci_esdhc_imx_hwinit(host);
>  
> -	if (host->irq_wake_enabled) {
> +	if (host->irq_wake_enabled)
>  		sdhci_disable_irq_wakeups(host);
> -		enable_irq(host->irq);
> -	}
> +
> +	enable_irq(host->irq);
>  
>  	/*
>  	 * restore the saved tuning delay value for the device which keep
> -- 
> 2.34.1
>