[PATCH net-next 0/2] net: dsa: mt7530: add EcoNet EN7528 built-in switch support

[PATCH net-next 0/2] net: dsa: mt7530: add EcoNet EN7528 built-in switch support

[Ahmed Naseef]

The EcoNet EN7528 is a MIPS SoC whose platform support is already
upstream. It integrates an MT7530 switch, memory-mapped like the built-in
switches of the MediaTek MT7988 and Airoha EN7581/AN7583 SoCs, but with a
true MT7530 core, four Gigabit PHYs on ports 1-4 and a CPU port at a fixed
1000 Mbps full duplex link.

Patch 1 documents the compatible, patch 2 adds the driver support.

Ahmed Naseef (2):
  dt-bindings: net: dsa: mediatek,mt7530: add econet,en7528-switch
  net: dsa: mt7530: add EN7528 support

 .../bindings/net/dsa/mediatek,mt7530.yaml     |  5 ++
 drivers/net/dsa/mt7530-mmio.c                 |  1 +
 drivers/net/dsa/mt7530.c                      | 56 ++++++++++++++++++-
 drivers/net/dsa/mt7530.h                      |  1 +
 4 files changed, 62 insertions(+), 1 deletion(-)


base-commit: fe3e786ef4eb6e47d2901f568a27bd920477bbe9
-- 
2.34.1

[PATCH net-next 1/2] dt-bindings: net: dsa: mediatek,mt7530: add econet,en7528-switch

[Ahmed Naseef]

The EcoNet EN7528 MIPS SoC integrates an MT7530 Gigabit switch,
memory-mapped in the SoC register space like the built-in switches of
the MediaTek MT7988 and Airoha EN7581/AN7583 SoCs. Its four user ports
are connected to integrated Gigabit PHYs and its CPU port is connected
internally to the SoC Ethernet MAC.

Add the econet,en7528-switch compatible, with the same constraints as
the other built-in switches.

Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
---
 .../devicetree/bindings/net/dsa/mediatek,mt7530.yaml         | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml b/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml
index 815a90808901..90b3582b7619 100644
--- a/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml
+++ b/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml
@@ -100,6 +100,10 @@ properties:
           Built-in switch of the Airoha AN7583 SoC
         const: airoha,an7583-switch
 
+      - description:
+          Built-in switch of the EcoNet EN7528 SoC
+        const: econet,en7528-switch
+
   reg:
     maxItems: 1
 
@@ -318,6 +322,7 @@ allOf:
             - mediatek,mt7988-switch
             - airoha,en7581-switch
             - airoha,an7583-switch
+            - econet,en7528-switch
     then:
       $ref: "#/$defs/builtin-dsa-port"
       properties:
-- 
2.34.1

Re: [PATCH net-next 1/2] dt-bindings: net: dsa: mediatek,mt7530: add econet,en7528-switch

[Conor Dooley]

[-- Attachment #1: Type: text/plain, Size: 1856 bytes --]

On Fri, Jul 10, 2026 at 02:54:23PM +0400, Ahmed Naseef wrote:
> The EcoNet EN7528 MIPS SoC integrates an MT7530 Gigabit switch,
> memory-mapped in the SoC register space like the built-in switches of
> the MediaTek MT7988 and Airoha EN7581/AN7583 SoCs. Its four user ports
> are connected to integrated Gigabit PHYs and its CPU port is connected
> internally to the SoC Ethernet MAC.

Please note what actually makes this different from the other devices
such that it cannot use a fallback. It's not clear from this description
if the described features are shared with other devices or unique.
pw-bot: changes-requested

Thanks,
Conor.

> 
> Add the econet,en7528-switch compatible, with the same constraints as
> the other built-in switches.
> 
> Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
> ---
>  .../devicetree/bindings/net/dsa/mediatek,mt7530.yaml         | 5 +++++
>  1 file changed, 5 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml b/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml
> index 815a90808901..90b3582b7619 100644
> --- a/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml
> +++ b/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml
> @@ -100,6 +100,10 @@ properties:
>            Built-in switch of the Airoha AN7583 SoC
>          const: airoha,an7583-switch
>  
> +      - description:
> +          Built-in switch of the EcoNet EN7528 SoC
> +        const: econet,en7528-switch
> +
>    reg:
>      maxItems: 1
>  
> @@ -318,6 +322,7 @@ allOf:
>              - mediatek,mt7988-switch
>              - airoha,en7581-switch
>              - airoha,an7583-switch
> +            - econet,en7528-switch
>      then:
>        $ref: "#/$defs/builtin-dsa-port"
>        properties:
> -- 
> 2.34.1
> 

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[PATCH net-next 2/2] net: dsa: mt7530: add EN7528 support

[Ahmed Naseef]

The EcoNet EN7528 SoC integrates an MT7530 switch (the chip revision
register reads 0x7530), memory-mapped in the SoC register space and
reached through the same MMIO glue used for the built-in switches of the
MediaTek MT7988 and Airoha EN7581/AN7583 SoCs. Its reset sequence and its
PHY indirect access registers are the same as on those switches, so add
an ID_EN7528 variant bound with the "econet,en7528-switch" compatible,
reusing mt7988_setup() and the indirect PHY accessors.

The switch core, however, is an MT7530 and not an MT7531 derivative: it
has no MT7531 CFC register, and the CPU port to trap frames to is set
through the MT7530-style CPU_EN / CPU_PORT fields of the MFC register, so
add it to the MT7530 handling in mt753x_conduit_state_change(). For the
same reason the MT7530 mirror and force-mode register layouts already
apply to it as the default of the MT753X_*() macros.

The four user ports (1-4) are connected to integrated Gigabit PHYs at
MDIO addresses 9-12 of the switch internal MDIO bus. The CPU port (port
6) is connected to the SoC Ethernet MAC at a fixed 1000 Mbps full duplex
link, so the port capabilities cannot be shared with the MT7988 and
EN7581 switches, whose CPU ports run at 10 Gbps.

The LAN GPHYs advertise EEE by default, but negotiating EEE with some
link partners results in an unstable link with dropped frames. Disable
EEE advertisement on them at setup time, like mt7531_setup() does for the
MT7531 switch PHYs.

Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
---
 drivers/net/dsa/mt7530-mmio.c |  1 +
 drivers/net/dsa/mt7530.c      | 56 ++++++++++++++++++++++++++++++++++-
 drivers/net/dsa/mt7530.h      |  1 +
 3 files changed, 57 insertions(+), 1 deletion(-)

diff --git a/drivers/net/dsa/mt7530-mmio.c b/drivers/net/dsa/mt7530-mmio.c
index 1dc8b93fb51a..1065671bcdd1 100644
--- a/drivers/net/dsa/mt7530-mmio.c
+++ b/drivers/net/dsa/mt7530-mmio.c
@@ -13,6 +13,7 @@
 static const struct of_device_id mt7988_of_match[] = {
 	{ .compatible = "airoha,an7583-switch", .data = &mt753x_table[ID_AN7583], },
 	{ .compatible = "airoha,en7581-switch", .data = &mt753x_table[ID_EN7581], },
+	{ .compatible = "econet,en7528-switch", .data = &mt753x_table[ID_EN7528], },
 	{ .compatible = "mediatek,mt7988-switch", .data = &mt753x_table[ID_MT7988], },
 	{ /* sentinel */ },
 };
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 3c2a3029b10c..2aecad77af9a 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -2912,6 +2912,30 @@ static void en7581_mac_port_get_caps(struct dsa_switch *ds, int port,
 	}
 }
 
+static void en7528_mac_port_get_caps(struct dsa_switch *ds, int port,
+				     struct phylink_config *config)
+{
+	switch (port) {
+	/* Ports which are connected to switch PHYs. There is no MII pinout. */
+	case 1 ... 4:
+		__set_bit(PHY_INTERFACE_MODE_INTERNAL,
+			  config->supported_interfaces);
+
+		config->mac_capabilities |= MAC_10 | MAC_100 | MAC_1000FD;
+		break;
+
+	/* Port 6 is connected to SoC's GMAC at 1000 Mbps full duplex. There
+	 * is no MII pinout.
+	 */
+	case 6:
+		__set_bit(PHY_INTERFACE_MODE_INTERNAL,
+			  config->supported_interfaces);
+
+		config->mac_capabilities |= MAC_1000FD;
+		break;
+	}
+}
+
 static void
 mt7530_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
 		  phy_interface_t interface)
@@ -3254,7 +3278,8 @@ mt753x_conduit_state_change(struct dsa_switch *ds,
 	 * forwarded to the numerically smallest CPU port whose conduit
 	 * interface is up.
 	 */
-	if (priv->id != ID_MT7530 && priv->id != ID_MT7621)
+	if (priv->id != ID_MT7530 && priv->id != ID_MT7621 &&
+	    priv->id != ID_EN7528)
 		return;
 
 	mask = BIT(cpu_dp->index);
@@ -3319,9 +3344,17 @@ static int mt753x_setup_tc(struct dsa_switch *ds, int port,
 	}
 }
 
+/* The EN7528 LAN ports are integrated GPHYs at MDIO addresses 9..12 (switch
+ * ports 1..4) on the switch internal MDIO bus, reachable only through the PHY
+ * indirect access registers. There is no mdiodev to derive the addresses from.
+ */
+#define EN7528_GPHY_BASE		9
+#define EN7528_NUM_GPHYS		4
+
 static int mt7988_setup(struct dsa_switch *ds)
 {
 	struct mt7530_priv *priv = ds->priv;
+	int i;
 
 	/* Reset the switch */
 	reset_control_assert(priv->rstc);
@@ -3342,6 +3375,17 @@ static int mt7988_setup(struct dsa_switch *ds)
 	/* Reset the switch PHYs */
 	mt7530_write(priv, MT7530_SYS_CTRL, SYS_CTRL_PHY_RST);
 
+	/* The EN7528 LAN GPHYs advertise EEE by default, but negotiating EEE
+	 * with common link partners (e.g. Realtek GbE NICs) results in an
+	 * unstable link with dropped frames. Disable EEE advertisement on
+	 * them.
+	 */
+	if (priv->id == ID_EN7528)
+		for (i = EN7528_GPHY_BASE;
+		     i < EN7528_GPHY_BASE + EN7528_NUM_GPHYS; i++)
+			mt7531_ind_c45_phy_write(priv, i, MDIO_MMD_AN,
+						 MDIO_AN_EEE_ADV, 0);
+
 	return mt7531_setup_common(ds);
 }
 
@@ -3459,6 +3503,16 @@ const struct mt753x_info mt753x_table[] = {
 		.phy_write_c45 = mt7531_ind_c45_phy_write,
 		.mac_port_get_caps = en7581_mac_port_get_caps,
 	},
+	[ID_EN7528] = {
+		.id = ID_EN7528,
+		.pcs_ops = &mt7530_pcs_ops,
+		.sw_setup = mt7988_setup,
+		.phy_read_c22 = mt7531_ind_c22_phy_read,
+		.phy_write_c22 = mt7531_ind_c22_phy_write,
+		.phy_read_c45 = mt7531_ind_c45_phy_read,
+		.phy_write_c45 = mt7531_ind_c45_phy_write,
+		.mac_port_get_caps = en7528_mac_port_get_caps,
+	},
 };
 EXPORT_SYMBOL_GPL(mt753x_table);
 
diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
index dd33b0df3419..5f1e841f42c0 100644
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -21,6 +21,7 @@ enum mt753x_id {
 	ID_MT7988 = 3,
 	ID_EN7581 = 4,
 	ID_AN7583 = 5,
+	ID_EN7528 = 6,
 };
 
 #define	NUM_TRGMII_CTRL			5
-- 
2.34.1

Re: [PATCH net-next 2/2] net: dsa: mt7530: add EN7528 support

[Andrew Lunn]

> +	/* The EN7528 LAN GPHYs advertise EEE by default, but negotiating EEE
> +	 * with common link partners (e.g. Realtek GbE NICs) results in an
> +	 * unstable link with dropped frames. Disable EEE advertisement on
> +	 * them.
> +	 */
> +	if (priv->id == ID_EN7528)
> +		for (i = EN7528_GPHY_BASE;
> +		     i < EN7528_GPHY_BASE + EN7528_NUM_GPHYS; i++)
> +			mt7531_ind_c45_phy_write(priv, i, MDIO_MMD_AN,
> +						 MDIO_AN_EEE_ADV, 0);
> +

The problem with this is, you can still use ethtool to enable EEE.

Please look at phylink_bringup_phy(), where it calls
phy_disable_eee().

    Andrew

---
pw-bot: cr

Re: [PATCH net-next 2/2] net: dsa: mt7530: add EN7528 support

[Ahmed Naseef]

On Fri, Jul 10, 2026 at 03:32:32PM +0200, Andrew Lunn wrote:
> > +	/* The EN7528 LAN GPHYs advertise EEE by default, but negotiating EEE
> > +	 * with common link partners (e.g. Realtek GbE NICs) results in an
> > +	 * unstable link with dropped frames. Disable EEE advertisement on
> > +	 * them.
> > +	 */
> > +	if (priv->id == ID_EN7528)
> > +		for (i = EN7528_GPHY_BASE;
> > +		     i < EN7528_GPHY_BASE + EN7528_NUM_GPHYS; i++)
> > +			mt7531_ind_c45_phy_write(priv, i, MDIO_MMD_AN,
> > +						 MDIO_AN_EEE_ADV, 0);
> > +
> 
> The problem with this is, you can still use ethtool to enable EEE.
> 
> Please look at phylink_bringup_phy(), where it calls
> phy_disable_eee().

Thanks, you are right , the register write is the wrong approach.

While looking at phylink_bringup_phy(), I noticed that the mt7530
driver sets config->lpi_capabilities but never config->lpi_interfaces.
Since

        mac_supports_eee = mac_supports_eee_ops && lpi_capabilities &&
                           !phy_interface_empty(lpi_interfaces);

that leaves mac_supports_eee false on all mt753x ports, so phylink
already takes the phy_disable_eee() path for every port and
phylink_ethtool_set_eee() returns -EOPNOTSUPP. On the EN7528 I
confirmed "ethtool --set-eee lan1 eee on" reports "Not supported", so
EEE cannot currently be enabled from userspace on this driver at all.
That looks like it unintentionally undid the "EEE can now be enabled
using ethtool" behaviour from commit 06dfcd4098cf ("net: dsa: mt7530:
fix enabling EEE on MT7531 switch on all boards"), starting with commit
9cf21773f535 ("net: dsa: mt7530: convert to phylink managed EEE"). That
is pre-existing and outside the scope of this series, just flagging it.

For the EN7528 the GPHYs report EEE capability, but the link stops
passing traffic once LPI is entered, so EEE must stay off regardless.
The register loop cannot express that to phylib, as you noted.

My plan for v2 is to not advertise lpi_capabilities for the EN7528, so
mac_supports_eee stays false by design and phylink disables EEE on
these PHYs via phy_disable_eee() and refuses to enable it from
userspace. Does that sound like the right approach to you, or would
you prefer it handled differently?

Thanks,
Ahmed


> 
>     Andrew
> 
> ---
> pw-bot: cr

Re: [PATCH net-next 2/2] net: dsa: mt7530: add EN7528 support

[Andrew Lunn]

> My plan for v2 is to not advertise lpi_capabilities for the EN7528, so
> mac_supports_eee stays false by design and phylink disables EEE on
> these PHYs via phy_disable_eee() and refuses to enable it from
> userspace. Does that sound like the right approach to you, or would
> you prefer it handled differently?

That sounds like the correct thing to do.

     Andrew