[PATCH V2 0/9] ARM: stm32: add initial STM32MPU support

[PATCH V2 0/9] ARM: stm32: add initial STM32MPU support

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

change V2:
-Add stm32 documentation in this serie to avoid merge conflict
thread: "https://patchwork.kernel.org/patch/10102573/"
-Split bindings (stm32.txt) to separate patches.
-Remove ARCH_STM32_MCU/MPU flags
-Adopt rst format for Documentation/arm/stm32 files
-s/STMicrolectronics/STMicroelectronics/g

Ludovic Barre (9):
  devicetree: bindings: Document supported STM32 SoC family
  Documentation: arm: stm32: move to rst format
  ARM: stm32: prepare stm32 family to welcome armv7 architecture
  devicetree: bindings: stm32: add support of STM32MP157
  ARM: stm32: add initial support for STM32MP157
  pinctrl: stm32: Add STM32MP157 MPU support
  ARM: configs: multi_v7: add stm32 support
  ARM: dts: stm32: add stm32mp157c initial support
  ARM: dts: stm32: add initial support of stm32mp157c eval board

 Documentation/arm/stm32/overview.rst               |   34 +
 Documentation/arm/stm32/overview.txt               |   33 -
 Documentation/arm/stm32/stm32f429-overview.rst     |   26 +
 Documentation/arm/stm32/stm32f429-overview.txt     |   22 -
 Documentation/arm/stm32/stm32f746-overview.rst     |   33 +
 Documentation/arm/stm32/stm32f746-overview.txt     |   34 -
 Documentation/arm/stm32/stm32h743-overview.rst     |   34 +
 Documentation/arm/stm32/stm32h743-overview.txt     |   30 -
 Documentation/arm/stm32/stm32mp157-overview.rst    |   19 +
 Documentation/devicetree/bindings/arm/stm32.txt    |   10 +
 .../bindings/pinctrl/st,stm32-pinctrl.txt          |    2 +
 arch/arm/boot/dts/Makefile                         |    6 +-
 arch/arm/boot/dts/stm32mp157-pinctrl.dtsi          |  185 ++
 arch/arm/boot/dts/stm32mp157c-ed1.dts              |   29 +
 arch/arm/boot/dts/stm32mp157c-ev1.dts              |   19 +
 arch/arm/boot/dts/stm32mp157c.dtsi                 |  139 ++
 arch/arm/configs/multi_v7_defconfig                |    3 +
 arch/arm/mach-stm32/Kconfig                        |   35 +-
 arch/arm/mach-stm32/Makefile                       |    3 +-
 arch/arm/mach-stm32/{board-dt.c => board-mcu-dt.c} |    0
 arch/arm/mach-stm32/board-mpu-dt.c                 |   16 +
 drivers/pinctrl/stm32/Kconfig                      |    6 +
 drivers/pinctrl/stm32/Makefile                     |    1 +
 drivers/pinctrl/stm32/pinctrl-stm32mp157.c         | 2188 ++++++++++++++++++++
 24 files changed, 2773 insertions(+), 134 deletions(-)
 create mode 100644 Documentation/arm/stm32/overview.rst
 delete mode 100644 Documentation/arm/stm32/overview.txt
 create mode 100644 Documentation/arm/stm32/stm32f429-overview.rst
 delete mode 100644 Documentation/arm/stm32/stm32f429-overview.txt
 create mode 100644 Documentation/arm/stm32/stm32f746-overview.rst
 delete mode 100644 Documentation/arm/stm32/stm32f746-overview.txt
 create mode 100644 Documentation/arm/stm32/stm32h743-overview.rst
 delete mode 100644 Documentation/arm/stm32/stm32h743-overview.txt
 create mode 100644 Documentation/arm/stm32/stm32mp157-overview.rst
 create mode 100644 Documentation/devicetree/bindings/arm/stm32.txt
 create mode 100644 arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
 create mode 100644 arch/arm/boot/dts/stm32mp157c-ed1.dts
 create mode 100644 arch/arm/boot/dts/stm32mp157c-ev1.dts
 create mode 100644 arch/arm/boot/dts/stm32mp157c.dtsi
 rename arch/arm/mach-stm32/{board-dt.c => board-mcu-dt.c} (100%)
 create mode 100644 arch/arm/mach-stm32/board-mpu-dt.c
 create mode 100644 drivers/pinctrl/stm32/pinctrl-stm32mp157.c

-- 
2.7.4

[PATCH V2 1/9] devicetree: bindings: Document supported STM32 SoC family

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This adds a list of supported STM32 SoC bindings.

Signed-off-by: Gwenael Treuveur <gwenael.treuveur@st.com>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/arm/stm32.txt | 9 +++++++++
 1 file changed, 9 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/stm32.txt

diff --git a/Documentation/devicetree/bindings/arm/stm32.txt b/Documentation/devicetree/bindings/arm/stm32.txt
new file mode 100644
index 0000000..05762b0
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/stm32.txt
@@ -0,0 +1,9 @@
+STMicroelectronics STM32 Platforms Device Tree Bindings
+
+Each device tree must specify which STM32 SoC it uses,
+using one of the following compatible strings:
+
+  st,stm32f429
+  st,stm32f469
+  st,stm32f746
+  st,stm32h743
-- 
2.7.4

[PATCH V2 1/9] devicetree: bindings: Document supported STM32 SoC family

[Linus Walleij]

On Mon, Dec 18, 2017 at 4:17 PM, Ludovic Barre <ludovic.Barre@st.com> wrote:

> From: Ludovic Barre <ludovic.barre@st.com>
>
> This adds a list of supported STM32 SoC bindings.
>
> Signed-off-by: Gwenael Treuveur <gwenael.treuveur@st.com>
> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
> Reviewed-by: Rob Herring <robh@kernel.org>

Patch applied.

Yours,
Linus Walleij

[PATCH V2 2/9] Documentation: arm: stm32: move to rst format

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch rewrites stm32 documentation to rst
(ReStructuredText) format.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 Documentation/arm/stm32/overview.rst           | 31 +++++++++++++++++++++++
 Documentation/arm/stm32/overview.txt           | 33 -------------------------
 Documentation/arm/stm32/stm32f429-overview.rst | 26 ++++++++++++++++++++
 Documentation/arm/stm32/stm32f429-overview.txt | 22 -----------------
 Documentation/arm/stm32/stm32f746-overview.rst | 33 +++++++++++++++++++++++++
 Documentation/arm/stm32/stm32f746-overview.txt | 34 --------------------------
 Documentation/arm/stm32/stm32h743-overview.rst | 34 ++++++++++++++++++++++++++
 Documentation/arm/stm32/stm32h743-overview.txt | 30 -----------------------
 8 files changed, 124 insertions(+), 119 deletions(-)
 create mode 100644 Documentation/arm/stm32/overview.rst
 delete mode 100644 Documentation/arm/stm32/overview.txt
 create mode 100644 Documentation/arm/stm32/stm32f429-overview.rst
 delete mode 100644 Documentation/arm/stm32/stm32f429-overview.txt
 create mode 100644 Documentation/arm/stm32/stm32f746-overview.rst
 delete mode 100644 Documentation/arm/stm32/stm32f746-overview.txt
 create mode 100644 Documentation/arm/stm32/stm32h743-overview.rst
 delete mode 100644 Documentation/arm/stm32/stm32h743-overview.txt

diff --git a/Documentation/arm/stm32/overview.rst b/Documentation/arm/stm32/overview.rst
new file mode 100644
index 0000000..6be6059
--- /dev/null
+++ b/Documentation/arm/stm32/overview.rst
@@ -0,0 +1,31 @@
+========================
+STM32 ARM Linux Overview
+========================
+
+Introduction
+------------
+
+The STMicroelectronics family of Cortex-M based MCUs are supported by the
+'STM32' platform of ARM Linux. Currently only the STM32F429 (Cortex-M4)
+and STM32F746 (Cortex-M7) are supported.
+
+Configuration
+-------------
+
+A generic configuration is provided for STM32 family, and can be used as the
+default by
+        make stm32_defconfig
+
+Layout
+------
+
+All the files for multiple machine families are located in the platform code
+contained in arch/arm/mach-stm32
+
+There is a generic board board-dt.c in the mach folder which support
+Flattened Device Tree, which means, it works with any compatible board with
+Device Trees.
+
+:Authors:
+
+Maxime Coquelin <mcoquelin.stm32@gmail.com>
diff --git a/Documentation/arm/stm32/overview.txt b/Documentation/arm/stm32/overview.txt
deleted file mode 100644
index a03b035..0000000
--- a/Documentation/arm/stm32/overview.txt
+++ /dev/null
@@ -1,33 +0,0 @@
-			STM32 ARM Linux Overview
-			========================
-
-Introduction
-------------
-
-  The STMicroelectronics family of Cortex-M based MCUs are supported by the
-  'STM32' platform of ARM Linux. Currently only the STM32F429 (Cortex-M4)
-  and STM32F746 (Cortex-M7) are supported.
-
-
-Configuration
--------------
-
-  A generic configuration is provided for STM32 family, and can be used as the
-  default by
-	make stm32_defconfig
-
-Layout
-------
-
-  All the files for multiple machine families are located in the platform code
-  contained in arch/arm/mach-stm32
-
-  There is a generic board board-dt.c in the mach folder which support
-  Flattened Device Tree, which means, it works with any compatible board with
-  Device Trees.
-
-
-Document Author
----------------
-
-  Maxime Coquelin <mcoquelin.stm32@gmail.com>
diff --git a/Documentation/arm/stm32/stm32f429-overview.rst b/Documentation/arm/stm32/stm32f429-overview.rst
new file mode 100644
index 0000000..18feda9
--- /dev/null
+++ b/Documentation/arm/stm32/stm32f429-overview.rst
@@ -0,0 +1,26 @@
+STM32F429 Overview
+==================
+
+Introduction
+------------
+
+The STM32F429 is a Cortex-M4 MCU aimed at various applications.
+It features:
+
+- ARM Cortex-M4 up to 180MHz with FPU
+- 2MB internal Flash Memory
+- External memory support through FMC controller (PSRAM, SDRAM, NOR, NAND)
+- I2C, SPI, SAI, CAN, USB OTG, Ethernet controllers
+- LCD controller & Camera interface
+- Cryptographic processor
+
+Resources
+---------
+
+Datasheet and reference manual are publicly available on ST website (STM32F429_).
+
+.. _STM32F429: http://www.st.com/web/en/catalog/mmc/FM141/SC1169/SS1577/LN1806?ecmp=stm32f429-439_pron_pr-ces2014_nov2013
+
+:Authors:
+
+Maxime Coquelin <mcoquelin.stm32@gmail.com>
diff --git a/Documentation/arm/stm32/stm32f429-overview.txt b/Documentation/arm/stm32/stm32f429-overview.txt
deleted file mode 100644
index 5206822..0000000
--- a/Documentation/arm/stm32/stm32f429-overview.txt
+++ /dev/null
@@ -1,22 +0,0 @@
-			STM32F429 Overview
-			==================
-
-  Introduction
-  ------------
-	The STM32F429 is a Cortex-M4 MCU aimed at various applications.
-	It features:
-	- ARM Cortex-M4 up to 180MHz with FPU
-	- 2MB internal Flash Memory
-	- External memory support through FMC controller (PSRAM, SDRAM, NOR, NAND)
-	- I2C, SPI, SAI, CAN, USB OTG, Ethernet controllers
-	- LCD controller & Camera interface
-	- Cryptographic processor
-
-  Resources
-  ---------
-	Datasheet and reference manual are publicly available on ST website:
-	- http://www.st.com/web/en/catalog/mmc/FM141/SC1169/SS1577/LN1806?ecmp=stm32f429-439_pron_pr-ces2014_nov2013
-
-  Document Author
-  ---------------
-	Maxime Coquelin <mcoquelin.stm32@gmail.com>
diff --git a/Documentation/arm/stm32/stm32f746-overview.rst b/Documentation/arm/stm32/stm32f746-overview.rst
new file mode 100644
index 0000000..b5f4b6c
--- /dev/null
+++ b/Documentation/arm/stm32/stm32f746-overview.rst
@@ -0,0 +1,33 @@
+STM32F746 Overview
+==================
+
+Introduction
+------------
+
+The STM32F746 is a Cortex-M7 MCU aimed at various applications.
+It features:
+
+- Cortex-M7 core running up to @216MHz
+- 1MB internal flash, 320KBytes internal RAM (+4KB of backup SRAM)
+- FMC controller to connect SDRAM, NOR and NAND memories
+- Dual mode QSPI
+- SD/MMC/SDIO support
+- Ethernet controller
+- USB OTFG FS & HS controllers
+- I2C, SPI, CAN busses support
+- Several 16 & 32 bits general purpose timers
+- Serial Audio interface
+- LCD controller
+- HDMI-CEC
+- SPDIFRX
+
+Resources
+---------
+
+Datasheet and reference manual are publicly available on ST website (STM32F746_).
+
+.. _STM32F746: http://www.st.com/content/st_com/en/products/microcontrollers/stm32-32-bit-arm-cortex-mcus/stm32f7-series/stm32f7x6/stm32f746ng.html
+
+:Authors:
+
+Alexandre Torgue <alexandre.torgue@st.com>
diff --git a/Documentation/arm/stm32/stm32f746-overview.txt b/Documentation/arm/stm32/stm32f746-overview.txt
deleted file mode 100644
index cffd2b1c..0000000
--- a/Documentation/arm/stm32/stm32f746-overview.txt
+++ /dev/null
@@ -1,34 +0,0 @@
-			STM32F746 Overview
-			==================
-
-  Introduction
-  ------------
-	The STM32F746 is a Cortex-M7 MCU aimed at various applications.
-	It features:
-	- Cortex-M7 core running up to @216MHz
-	- 1MB internal flash, 320KBytes internal RAM (+4KB of backup SRAM)
-	- FMC controller to connect SDRAM, NOR and NAND memories
-	- Dual mode QSPI
-	- SD/MMC/SDIO support
-	- Ethernet controller
-	- USB OTFG FS & HS controllers
-	- I2C, SPI, CAN busses support
-	- Several 16 & 32 bits general purpose timers
-	- Serial Audio interface
-	- LCD controller
-	- HDMI-CEC
-	- SPDIFRX
-
-  Resources
-  ---------
-	Datasheet and reference manual are publicly available on ST website:
-	- http://www.st.com/content/st_com/en/products/microcontrollers/stm32-32-bit-arm-cortex-mcus/stm32f7-series/stm32f7x6/stm32f746ng.html
-
-  Document Author
-  ---------------
-	Alexandre Torgue <alexandre.torgue@st.com>
-
-
-
-
-
diff --git a/Documentation/arm/stm32/stm32h743-overview.rst b/Documentation/arm/stm32/stm32h743-overview.rst
new file mode 100644
index 0000000..3458dc0
--- /dev/null
+++ b/Documentation/arm/stm32/stm32h743-overview.rst
@@ -0,0 +1,34 @@
+STM32H743 Overview
+==================
+
+Introduction
+------------
+
+The STM32H743 is a Cortex-M7 MCU aimed at various applications.
+It features:
+
+- Cortex-M7 core running up to @400MHz
+- 2MB internal flash, 1MBytes internal RAM
+- FMC controller to connect SDRAM, NOR and NAND memories
+- Dual mode QSPI
+- SD/MMC/SDIO support
+- Ethernet controller
+- USB OTFG FS & HS controllers
+- I2C, SPI, CAN busses support
+- Several 16 & 32 bits general purpose timers
+- Serial Audio interface
+- LCD controller
+- HDMI-CEC
+- SPDIFRX
+- DFSDM
+
+Resources
+---------
+
+Datasheet and reference manual are publicly available on ST website (STM32H743_).
+
+.. _STM32H743: http://www.st.com/en/microcontrollers/stm32h7x3.html?querycriteria=productId=LN2033
+
+:Authors:
+
+Alexandre Torgue <alexandre.torgue@st.com>
diff --git a/Documentation/arm/stm32/stm32h743-overview.txt b/Documentation/arm/stm32/stm32h743-overview.txt
deleted file mode 100644
index 3031cba..0000000
--- a/Documentation/arm/stm32/stm32h743-overview.txt
+++ /dev/null
@@ -1,30 +0,0 @@
-			STM32H743 Overview
-			==================
-
-  Introduction
-  ------------
-	The STM32H743 is a Cortex-M7 MCU aimed at various applications.
-	It features:
-	- Cortex-M7 core running up to @400MHz
-	- 2MB internal flash, 1MBytes internal RAM
-	- FMC controller to connect SDRAM, NOR and NAND memories
-	- Dual mode QSPI
-	- SD/MMC/SDIO support
-	- Ethernet controller
-	- USB OTFG FS & HS controllers
-	- I2C, SPI, CAN busses support
-	- Several 16 & 32 bits general purpose timers
-	- Serial Audio interface
-	- LCD controller
-	- HDMI-CEC
-	- SPDIFRX
-	- DFSDM
-
-  Resources
-  ---------
-	Datasheet and reference manual are publicly available on ST website:
-	- http://www.st.com/en/microcontrollers/stm32h7x3.html?querycriteria=productId=LN2033
-
-  Document Author
-  ---------------
-	Alexandre Torgue <alexandre.torgue@st.com>
-- 
2.7.4

[PATCH V2 3/9] ARM: stm32: prepare stm32 family to welcome armv7 architecture

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch prepares the STM32 machine for the integration of Cortex-A
based microprocessor (MPU), on top of the existing Cortex-M
microcontroller family (MCU). Since both MCUs and MPUs are sharing
common hardware blocks we can keep using ARCH_STM32 flag for most of
them. If a hardware block is specific to one family we can use either
ARM_SINGLE_ARMV7M or ARCH_MULTI_V7 flag.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 Documentation/arm/stm32/overview.rst               | 21 +++++++++--------
 arch/arm/mach-stm32/Kconfig                        | 27 ++++++++++++----------
 arch/arm/mach-stm32/Makefile                       |  2 +-
 arch/arm/mach-stm32/{board-dt.c => board-mcu-dt.c} |  0
 4 files changed, 28 insertions(+), 22 deletions(-)
 rename arch/arm/mach-stm32/{board-dt.c => board-mcu-dt.c} (100%)

diff --git a/Documentation/arm/stm32/overview.rst b/Documentation/arm/stm32/overview.rst
index 6be6059..3da6a8e 100644
--- a/Documentation/arm/stm32/overview.rst
+++ b/Documentation/arm/stm32/overview.rst
@@ -5,16 +5,17 @@ STM32 ARM Linux Overview
 Introduction
 ------------
 
-The STMicroelectronics family of Cortex-M based MCUs are supported by the
-'STM32' platform of ARM Linux. Currently only the STM32F429 (Cortex-M4)
-and STM32F746 (Cortex-M7) are supported.
+The STMicroelectronics STM32 family of Cortex-A microprocessors (MPUs) and
+Cortex-M microcontrollers (MCUs) are supported by the 'STM32' platform of
+ARM Linux.
 
 Configuration
 -------------
 
-A generic configuration is provided for STM32 family, and can be used as the
-default by
+For MCUs, use the provided default configuration:
         make stm32_defconfig
+For MPUs, use multi_v7 configuration:
+        make multi_v7_defconfig
 
 Layout
 ------
@@ -22,10 +23,12 @@ Layout
 All the files for multiple machine families are located in the platform code
 contained in arch/arm/mach-stm32
 
-There is a generic board board-dt.c in the mach folder which support
-Flattened Device Tree, which means, it works with any compatible board with
-Device Trees.
+There are generic boards board-mcu-dt.c and board-mpu-dt.c files in the mach
+folder which support Flattened Device Tree, which means, they work with any
+compatible board with Device Trees.
 
 :Authors:
 
-Maxime Coquelin <mcoquelin.stm32@gmail.com>
+- Maxime Coquelin <mcoquelin.stm32@gmail.com>
+- Ludovic Barre <ludovic.barre@st.com>
+- Gerald Baeza <gerald.baeza@st.com>
diff --git a/arch/arm/mach-stm32/Kconfig b/arch/arm/mach-stm32/Kconfig
index 0d1889b..e0f744b 100644
--- a/arch/arm/mach-stm32/Kconfig
+++ b/arch/arm/mach-stm32/Kconfig
@@ -1,8 +1,7 @@
-config ARCH_STM32
-	bool "STMicrolectronics STM32"
-	depends on ARM_SINGLE_ARMV7M
+menuconfig ARCH_STM32
+	bool "STMicroelectronics STM32 family" if ARM_SINGLE_ARMV7M || ARCH_MULTI_V7
+	select ARMV7M_SYSTICK if ARM_SINGLE_ARMV7M
 	select ARCH_HAS_RESET_CONTROLLER
-	select ARMV7M_SYSTICK
 	select CLKSRC_STM32
 	select PINCTRL
 	select RESET_CONTROLLER
@@ -10,22 +9,26 @@ config ARCH_STM32
 	help
 	  Support for STMicroelectronics STM32 processors.
 
+if ARCH_STM32
+
 config MACH_STM32F429
-	bool "STMicrolectronics STM32F429"
-	depends on ARCH_STM32
+	bool "STMicroelectronics STM32F429"
+	depends on ARM_SINGLE_ARMV7M
 	default y
 
 config MACH_STM32F469
-	bool "STMicrolectronics STM32F469"
-	depends on ARCH_STM32
+	bool "STMicroelectronics STM32F469"
+	depends on ARM_SINGLE_ARMV7M
 	default y
 
 config MACH_STM32F746
-	bool "STMicrolectronics STM32F746"
-	depends on ARCH_STM32
+	bool "STMicroelectronics STM32F746"
+	depends on ARM_SINGLE_ARMV7M
 	default y
 
 config MACH_STM32H743
-	bool "STMicrolectronics STM32H743"
-	depends on ARCH_STM32
+	bool "STMicroelectronics STM32H743"
+	depends on ARM_SINGLE_ARMV7M
 	default y
+
+endif
diff --git a/arch/arm/mach-stm32/Makefile b/arch/arm/mach-stm32/Makefile
index bd0b7b5..5940af1 100644
--- a/arch/arm/mach-stm32/Makefile
+++ b/arch/arm/mach-stm32/Makefile
@@ -1 +1 @@
-obj-y += board-dt.o
+obj-$(CONFIG_ARM_SINGLE_ARMV7M) += board-mcu-dt.o
diff --git a/arch/arm/mach-stm32/board-dt.c b/arch/arm/mach-stm32/board-mcu-dt.c
similarity index 100%
rename from arch/arm/mach-stm32/board-dt.c
rename to arch/arm/mach-stm32/board-mcu-dt.c
-- 
2.7.4

[PATCH V2 3/9] ARM: stm32: prepare stm32 family to welcome armv7 architecture

[Arnd Bergmann]

On Mon, Dec 18, 2017 at 4:17 PM, Ludovic Barre <ludovic.Barre@st.com> wrote:
> From: Ludovic Barre <ludovic.barre@st.com>
>
> This patch prepares the STM32 machine for the integration of Cortex-A
> based microprocessor (MPU), on top of the existing Cortex-M
> microcontroller family (MCU). Since both MCUs and MPUs are sharing
> common hardware blocks we can keep using ARCH_STM32 flag for most of
> them. If a hardware block is specific to one family we can use either
> ARM_SINGLE_ARMV7M or ARCH_MULTI_V7 flag.
>
> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>

Looks good overall. Two more small comments:


>
> +if ARCH_STM32
> +
>  config MACH_STM32F429
> -       bool "STMicrolectronics STM32F429"
> -       depends on ARCH_STM32
> +       bool "STMicroelectronics STM32F429"
> +       depends on ARM_SINGLE_ARMV7M
>         default y

Instead of the explicit dependency for each board, I'd leave the surrounding
'if ARM_SINGLE_ARMV7M'. I think you had in v1.

> diff --git a/arch/arm/mach-stm32/Makefile b/arch/arm/mach-stm32/Makefile
> index bd0b7b5..5940af1 100644
> --- a/arch/arm/mach-stm32/Makefile
> +++ b/arch/arm/mach-stm32/Makefile
> @@ -1 +1 @@
> -obj-y += board-dt.o
> +obj-$(CONFIG_ARM_SINGLE_ARMV7M) += board-mcu-dt.o
> diff --git a/arch/arm/mach-stm32/board-dt.c b/arch/arm/mach-stm32/board-mcu-dt.c
> similarity index 100%
> rename from arch/arm/mach-stm32/board-dt.c
> rename to arch/arm/mach-stm32/board-mcu-dt.c

Why the rename? I don't expect the new machines to have any notable
contents in a board file, if any at all, so just use one file for both.
I see the board-dt.c file refers to armv7m_restart, we can either put
that in an #ifdef, or find a way to make it the default for all armv7-m
platforms that don't provide any other restart method.

     Arnd

[PATCH V2 3/9] ARM: stm32: prepare stm32 family to welcome armv7 architecture

[Alexandre Torgue]

On 12/18/2017 09:24 PM, Arnd Bergmann wrote:
> On Mon, Dec 18, 2017 at 4:17 PM, Ludovic Barre <ludovic.Barre@st.com> wrote:
>> From: Ludovic Barre <ludovic.barre@st.com>
>>
>> This patch prepares the STM32 machine for the integration of Cortex-A
>> based microprocessor (MPU), on top of the existing Cortex-M
>> microcontroller family (MCU). Since both MCUs and MPUs are sharing
>> common hardware blocks we can keep using ARCH_STM32 flag for most of
>> them. If a hardware block is specific to one family we can use either
>> ARM_SINGLE_ARMV7M or ARCH_MULTI_V7 flag.
>>
>> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
> 
> Looks good overall. Two more small comments:
> 
> 
>>
>> +if ARCH_STM32
>> +
>>   config MACH_STM32F429
>> -       bool "STMicrolectronics STM32F429"
>> -       depends on ARCH_STM32
>> +       bool "STMicroelectronics STM32F429"
>> +       depends on ARM_SINGLE_ARMV7M
>>          default y
> 
> Instead of the explicit dependency for each board, I'd leave the surrounding
> 'if ARM_SINGLE_ARMV7M'. I think you had in v1.
> 
>> diff --git a/arch/arm/mach-stm32/Makefile b/arch/arm/mach-stm32/Makefile
>> index bd0b7b5..5940af1 100644
>> --- a/arch/arm/mach-stm32/Makefile
>> +++ b/arch/arm/mach-stm32/Makefile
>> @@ -1 +1 @@
>> -obj-y += board-dt.o
>> +obj-$(CONFIG_ARM_SINGLE_ARMV7M) += board-mcu-dt.o
>> diff --git a/arch/arm/mach-stm32/board-dt.c b/arch/arm/mach-stm32/board-mcu-dt.c
>> similarity index 100%
>> rename from arch/arm/mach-stm32/board-dt.c
>> rename to arch/arm/mach-stm32/board-mcu-dt.c
> 
> Why the rename? I don't expect the new machines to have any notable
> contents in a board file, if any at all, so just use one file for both.
> I see the board-dt.c file refers to armv7m_restart, we can either put
> that in an #ifdef, or find a way to make it the default for all armv7-m
> platforms that don't provide any other restart method.
> 
Currently "restart" is not functional on stm32 MCU (at least for 
stm32f746, I will check on others MCU). My fear is if Ludovic made some 
patches to make "armv7m_restart" the default ".restart" function for all 
armv7-m platform, he will not be able to test it on stm32 MCU (as it is 
not currently working). I propose to do it in 2 steps:

1-Keep as you suggest only one board-dt.c file for both (MCU and MPU) 
and remove ".restart" function.

2-Investigate and send patches around ".restart" for both in an other 
series.

regards
Alex


>       Arnd
> 

[PATCH V2 3/9] ARM: stm32: prepare stm32 family to welcome armv7 architecture

[Ludovic BARRE]

hi Arnd

just a ping, on Alex's proposal (below) about armv7m_restart
(Currently "restart" is not functional on stm32 MCU).

BR
Ludo
On 12/19/2017 03:38 PM, Alexandre Torgue wrote:
> 
> 
> On 12/18/2017 09:24 PM, Arnd Bergmann wrote:
>> On Mon, Dec 18, 2017 at 4:17 PM, Ludovic Barre <ludovic.Barre@st.com> 
>> wrote:
>>> From: Ludovic Barre <ludovic.barre@st.com>
>>>
>>> This patch prepares the STM32 machine for the integration of Cortex-A
>>> based microprocessor (MPU), on top of the existing Cortex-M
>>> microcontroller family (MCU). Since both MCUs and MPUs are sharing
>>> common hardware blocks we can keep using ARCH_STM32 flag for most of
>>> them. If a hardware block is specific to one family we can use either
>>> ARM_SINGLE_ARMV7M or ARCH_MULTI_V7 flag.
>>>
>>> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
>>
>> Looks good overall. Two more small comments:
>>
>>
>>>
>>> +if ARCH_STM32
>>> +
>>> ? config MACH_STM32F429
>>> -?????? bool "STMicrolectronics STM32F429"
>>> -?????? depends on ARCH_STM32
>>> +?????? bool "STMicroelectronics STM32F429"
>>> +?????? depends on ARM_SINGLE_ARMV7M
>>> ???????? default y
>>
>> Instead of the explicit dependency for each board, I'd leave the 
>> surrounding
>> 'if ARM_SINGLE_ARMV7M'. I think you had in v1.
>>
>>> diff --git a/arch/arm/mach-stm32/Makefile b/arch/arm/mach-stm32/Makefile
>>> index bd0b7b5..5940af1 100644
>>> --- a/arch/arm/mach-stm32/Makefile
>>> +++ b/arch/arm/mach-stm32/Makefile
>>> @@ -1 +1 @@
>>> -obj-y += board-dt.o
>>> +obj-$(CONFIG_ARM_SINGLE_ARMV7M) += board-mcu-dt.o
>>> diff --git a/arch/arm/mach-stm32/board-dt.c 
>>> b/arch/arm/mach-stm32/board-mcu-dt.c
>>> similarity index 100%
>>> rename from arch/arm/mach-stm32/board-dt.c
>>> rename to arch/arm/mach-stm32/board-mcu-dt.c
>>
>> Why the rename? I don't expect the new machines to have any notable
>> contents in a board file, if any at all, so just use one file for both.
>> I see the board-dt.c file refers to armv7m_restart, we can either put
>> that in an #ifdef, or find a way to make it the default for all armv7-m
>> platforms that don't provide any other restart method.
>>
> Currently "restart" is not functional on stm32 MCU (at least for 
> stm32f746, I will check on others MCU). My fear is if Ludovic made some 
> patches to make "armv7m_restart" the default ".restart" function for all 
> armv7-m platform, he will not be able to test it on stm32 MCU (as it is 
> not currently working). I propose to do it in 2 steps:
> 
> 1-Keep as you suggest only one board-dt.c file for both (MCU and MPU) 
> and remove ".restart" function.
> 
> 2-Investigate and send patches around ".restart" for both in an other 
> series.

I resend

> 
> regards
> Alex
> 
> 
>> ????? Arnd
>>

[PATCH V2 3/9] ARM: stm32: prepare stm32 family to welcome armv7 architecture

[Arnd Bergmann]

On Thu, Dec 21, 2017 at 5:39 PM, Ludovic BARRE <ludovic.barre@st.com> wrote:

>>>
>> Currently "restart" is not functional on stm32 MCU (at least for
>> stm32f746, I will check on others MCU). My fear is if Ludovic made some
>> patches to make "armv7m_restart" the default ".restart" function for all
>> armv7-m platform, he will not be able to test it on stm32 MCU (as it is not
>> currently working). I propose to do it in 2 steps:
>>
>> 1-Keep as you suggest only one board-dt.c file for both (MCU and MPU) and
>> remove ".restart" function.
>>
>> 2-Investigate and send patches around ".restart" for both in an other
>> series.
>
>
> I resend

Yes, that seems fine.

       Arnd

[PATCH V2 3/9] ARM: stm32: prepare stm32 family to welcome armv7 architecture

[Ludovic BARRE]

On 12/18/2017 09:24 PM, Arnd Bergmann wrote:
> On Mon, Dec 18, 2017 at 4:17 PM, Ludovic Barre <ludovic.Barre@st.com> wrote:
>> From: Ludovic Barre <ludovic.barre@st.com>
>>
>> This patch prepares the STM32 machine for the integration of Cortex-A
>> based microprocessor (MPU), on top of the existing Cortex-M
>> microcontroller family (MCU). Since both MCUs and MPUs are sharing
>> common hardware blocks we can keep using ARCH_STM32 flag for most of
>> them. If a hardware block is specific to one family we can use either
>> ARM_SINGLE_ARMV7M or ARCH_MULTI_V7 flag.
>>
>> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
> 
> Looks good overall. Two more small comments:
> 
> 
>>
>> +if ARCH_STM32
>> +
>>   config MACH_STM32F429
>> -       bool "STMicrolectronics STM32F429"
>> -       depends on ARCH_STM32
>> +       bool "STMicroelectronics STM32F429"
>> +       depends on ARM_SINGLE_ARMV7M
>>          default y
> 
> Instead of the explicit dependency for each board, I'd leave the surrounding
> 'if ARM_SINGLE_ARMV7M'. I think you had in v1.

As you suggest, I follow mach-at91 example.
The point is on "depends on ARM_SINGLE_ARMV7M" ?
You prefer this way:
config MACH_STM32F429
	bool "STMicroelectronics STM32F429" if ARM_SINGLE_ARMV7M
	default y

BR
Ludo

> 
>> diff --git a/arch/arm/mach-stm32/Makefile b/arch/arm/mach-stm32/Makefile
>> index bd0b7b5..5940af1 100644
>> --- a/arch/arm/mach-stm32/Makefile
>> +++ b/arch/arm/mach-stm32/Makefile
>> @@ -1 +1 @@
>> -obj-y += board-dt.o
>> +obj-$(CONFIG_ARM_SINGLE_ARMV7M) += board-mcu-dt.o
>> diff --git a/arch/arm/mach-stm32/board-dt.c b/arch/arm/mach-stm32/board-mcu-dt.c
>> similarity index 100%
>> rename from arch/arm/mach-stm32/board-dt.c
>> rename to arch/arm/mach-stm32/board-mcu-dt.c
> 
> Why the rename? I don't expect the new machines to have any notable
> contents in a board file, if any at all, so just use one file for both.
> I see the board-dt.c file refers to armv7m_restart, we can either put
> that in an #ifdef, or find a way to make it the default for all armv7-m
> platforms that don't provide any other restart method.
> 
>       Arnd
> 

[PATCH V2 3/9] ARM: stm32: prepare stm32 family to welcome armv7 architecture

[Arnd Bergmann]

On Tue, Dec 19, 2017 at 3:43 PM, Ludovic BARRE <ludovic.barre@st.com> wrote:
>
>
> On 12/18/2017 09:24 PM, Arnd Bergmann wrote:
>>
>> On Mon, Dec 18, 2017 at 4:17 PM, Ludovic Barre <ludovic.Barre@st.com>
>> wrote:
>>>
>>> From: Ludovic Barre <ludovic.barre@st.com>
>>>
>>> This patch prepares the STM32 machine for the integration of Cortex-A
>>> based microprocessor (MPU), on top of the existing Cortex-M
>>> microcontroller family (MCU). Since both MCUs and MPUs are sharing
>>> common hardware blocks we can keep using ARCH_STM32 flag for most of
>>> them. If a hardware block is specific to one family we can use either
>>> ARM_SINGLE_ARMV7M or ARCH_MULTI_V7 flag.
>>>
>>> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
>>
>>
>> Looks good overall. Two more small comments:
>>
>>
>>>
>>> +if ARCH_STM32
>>> +
>>>   config MACH_STM32F429
>>> -       bool "STMicrolectronics STM32F429"
>>> -       depends on ARCH_STM32
>>> +       bool "STMicroelectronics STM32F429"
>>> +       depends on ARM_SINGLE_ARMV7M
>>>          default y
>>
>>
>> Instead of the explicit dependency for each board, I'd leave the
>> surrounding
>> 'if ARM_SINGLE_ARMV7M'. I think you had in v1.
>
>
> As you suggest, I follow mach-at91 example.
> The point is on "depends on ARM_SINGLE_ARMV7M" ?
> You prefer this way:
> config MACH_STM32F429
>         bool "STMicroelectronics STM32F429" if ARM_SINGLE_ARMV7M
>         default y
>

No, that would be wrong, that way you would always enable
MACH_STM32F429 when ARM_SINGLE_ARMV7M is turned
off, which is exactly the wrong way round. What I meant is

if ARCH_STM32

if ARM_SINGLE_ARMV7M

config MACH_STM32F429
         bool "STMicrolectronics STM32F429"

config MACH_STM32...
          ...

endif # ARMv7-M

if ARCH_MULTI_V7

config MACH_STM32...
          ...

endif # ARMv7-A

endif # STM32

       Arnd

[PATCH V2 3/9] ARM: stm32: prepare stm32 family to welcome armv7 architecture

[Ludovic BARRE]

On 12/19/2017 04:26 PM, Arnd Bergmann wrote:
> On Tue, Dec 19, 2017 at 3:43 PM, Ludovic BARRE <ludovic.barre@st.com> wrote:
>>
>>
>> On 12/18/2017 09:24 PM, Arnd Bergmann wrote:
>>>
>>> On Mon, Dec 18, 2017 at 4:17 PM, Ludovic Barre <ludovic.Barre@st.com>
>>> wrote:
>>>>
>>>> From: Ludovic Barre <ludovic.barre@st.com>
>>>>
>>>> This patch prepares the STM32 machine for the integration of Cortex-A
>>>> based microprocessor (MPU), on top of the existing Cortex-M
>>>> microcontroller family (MCU). Since both MCUs and MPUs are sharing
>>>> common hardware blocks we can keep using ARCH_STM32 flag for most of
>>>> them. If a hardware block is specific to one family we can use either
>>>> ARM_SINGLE_ARMV7M or ARCH_MULTI_V7 flag.
>>>>
>>>> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
>>>
>>>
>>> Looks good overall. Two more small comments:
>>>
>>>
>>>>
>>>> +if ARCH_STM32
>>>> +
>>>>    config MACH_STM32F429
>>>> -       bool "STMicrolectronics STM32F429"
>>>> -       depends on ARCH_STM32
>>>> +       bool "STMicroelectronics STM32F429"
>>>> +       depends on ARM_SINGLE_ARMV7M
>>>>           default y
>>>
>>>
>>> Instead of the explicit dependency for each board, I'd leave the
>>> surrounding
>>> 'if ARM_SINGLE_ARMV7M'. I think you had in v1.
>>
>>
>> As you suggest, I follow mach-at91 example.
>> The point is on "depends on ARM_SINGLE_ARMV7M" ?
>> You prefer this way:
>> config MACH_STM32F429
>>          bool "STMicroelectronics STM32F429" if ARM_SINGLE_ARMV7M
>>          default y
>>
> 
> No, that would be wrong, that way you would always enable
> MACH_STM32F429 when ARM_SINGLE_ARMV7M is turned
> off, which is exactly the wrong way round. What I meant is
> 
> if ARCH_STM32
> 
> if ARM_SINGLE_ARMV7M
> 
> config MACH_STM32F429
>           bool "STMicrolectronics STM32F429"
> 
> config MACH_STM32...
>            ...
> 
> endif # ARMv7-M
> 
> if ARCH_MULTI_V7
> 
> config MACH_STM32...
>            ...
> 
> endif # ARMv7-A
> 
> endif # STM32
> 
>         Arnd
> 
Ok, it's clear :-)

[PATCH V2 4/9] devicetree: bindings: stm32: add support of STM32MP157

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds STM32MP157 SoC bindings.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 Documentation/devicetree/bindings/arm/stm32.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/stm32.txt b/Documentation/devicetree/bindings/arm/stm32.txt
index 05762b0..6808ed9 100644
--- a/Documentation/devicetree/bindings/arm/stm32.txt
+++ b/Documentation/devicetree/bindings/arm/stm32.txt
@@ -7,3 +7,4 @@ using one of the following compatible strings:
   st,stm32f469
   st,stm32f746
   st,stm32h743
+  st,stm32mp157
-- 
2.7.4

[PATCH V2 4/9] devicetree: bindings: stm32: add support of STM32MP157

[Rob Herring]

On Mon, Dec 18, 2017 at 04:17:47PM +0100, Ludovic Barre wrote:
> From: Ludovic Barre <ludovic.barre@st.com>
> 
> This patch adds STM32MP157 SoC bindings.
> 
> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
> ---
>  Documentation/devicetree/bindings/arm/stm32.txt | 1 +
>  1 file changed, 1 insertion(+)

"dt-bindings: ..." is the preferred subject prefix. Otherwise,

Reviewed-by: Rob Herring <robh@kernel.org>

[PATCH V2 5/9] ARM: stm32: add initial support for STM32MP157

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds initial support of STM32MP157 microprocessor (MPU)
based on Arm Cortex-A7. New Cortex-A infrastructure (gic, timer,...)
are selected if ARCH_MULTI_V7 is defined.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 Documentation/arm/stm32/stm32mp157-overview.rst | 19 +++++++++++++++++++
 arch/arm/mach-stm32/Kconfig                     |  8 ++++++++
 arch/arm/mach-stm32/Makefile                    |  1 +
 arch/arm/mach-stm32/board-mpu-dt.c              | 16 ++++++++++++++++
 4 files changed, 44 insertions(+)
 create mode 100644 Documentation/arm/stm32/stm32mp157-overview.rst
 create mode 100644 arch/arm/mach-stm32/board-mpu-dt.c

diff --git a/Documentation/arm/stm32/stm32mp157-overview.rst b/Documentation/arm/stm32/stm32mp157-overview.rst
new file mode 100644
index 0000000..62e176d
--- /dev/null
+++ b/Documentation/arm/stm32/stm32mp157-overview.rst
@@ -0,0 +1,19 @@
+STM32MP157 Overview
+===================
+
+Introduction
+------------
+
+The STM32MP157 is a Cortex-A MPU aimed at various applications.
+It features:
+
+- Dual core Cortex-A7 application core
+- 2D/3D image composition with GPU
+- Standard memories interface support
+- Standard connectivity, widely inherited from the STM32 MCU family
+- Comprehensive security support
+
+:Authors:
+
+- Ludovic Barre <ludovic.barre@st.com>
+- Gerald Baeza <gerald.baeza@st.com>
diff --git a/arch/arm/mach-stm32/Kconfig b/arch/arm/mach-stm32/Kconfig
index e0f744b..146e22f 100644
--- a/arch/arm/mach-stm32/Kconfig
+++ b/arch/arm/mach-stm32/Kconfig
@@ -1,6 +1,9 @@
 menuconfig ARCH_STM32
 	bool "STMicroelectronics STM32 family" if ARM_SINGLE_ARMV7M || ARCH_MULTI_V7
 	select ARMV7M_SYSTICK if ARM_SINGLE_ARMV7M
+	select HAVE_ARM_ARCH_TIMER if ARCH_MULTI_V7
+	select ARM_GIC if ARCH_MULTI_V7
+	select ARM_PSCI if ARCH_MULTI_V7
 	select ARCH_HAS_RESET_CONTROLLER
 	select CLKSRC_STM32
 	select PINCTRL
@@ -31,4 +34,9 @@ config MACH_STM32H743
 	depends on ARM_SINGLE_ARMV7M
 	default y
 
+config MACH_STM32MP157
+	bool "STMicroelectronics STM32MP157"
+	depends on ARCH_MULTI_V7
+	default y
+
 endif
diff --git a/arch/arm/mach-stm32/Makefile b/arch/arm/mach-stm32/Makefile
index 5940af1..2cc3542 100644
--- a/arch/arm/mach-stm32/Makefile
+++ b/arch/arm/mach-stm32/Makefile
@@ -1 +1,2 @@
 obj-$(CONFIG_ARM_SINGLE_ARMV7M) += board-mcu-dt.o
+obj-$(CONFIG_ARCH_MULTI_V7) += board-mpu-dt.o
diff --git a/arch/arm/mach-stm32/board-mpu-dt.c b/arch/arm/mach-stm32/board-mpu-dt.c
new file mode 100644
index 0000000..9e18405
--- /dev/null
+++ b/arch/arm/mach-stm32/board-mpu-dt.c
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
+ */
+#include <asm/mach/arch.h>
+#include <linux/of_platform.h>
+
+static const char *const stm32mp_compat[] __initconst = {
+	"st,stm32mp157",
+	NULL
+};
+
+DT_MACHINE_START(STM32MPDT, "STM32 MP (Device Tree Support)")
+	.dt_compat = stm32mp_compat,
+MACHINE_END
-- 
2.7.4

[PATCH V2 6/9] pinctrl: stm32: Add STM32MP157 MPU support

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This driver consists of 2 controllers due to a hole in mapping:
-1 controller for GPIO bankA to K.
-1 controller for GPIO bankZ.

Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../bindings/pinctrl/st,stm32-pinctrl.txt          |    2 +
 drivers/pinctrl/stm32/Kconfig                      |    6 +
 drivers/pinctrl/stm32/Makefile                     |    1 +
 drivers/pinctrl/stm32/pinctrl-stm32mp157.c         | 2188 ++++++++++++++++++++
 4 files changed, 2197 insertions(+)
 create mode 100644 drivers/pinctrl/stm32/pinctrl-stm32mp157.c

diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
index 58c2a4c..2c46f30 100644
--- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
@@ -12,6 +12,8 @@ Required properies:
    "st,stm32f469-pinctrl"
    "st,stm32f746-pinctrl"
    "st,stm32h743-pinctrl"
+   "st,stm32mp157-pinctrl"
+   "st,stm32mp157-z-pinctrl"
  - #address-cells: The value of this property must be 1
  - #size-cells	: The value of this property must be 1
  - ranges	: defines mapping between pin controller node (parent) to
diff --git a/drivers/pinctrl/stm32/Kconfig b/drivers/pinctrl/stm32/Kconfig
index 7e1fe39..a6d045d 100644
--- a/drivers/pinctrl/stm32/Kconfig
+++ b/drivers/pinctrl/stm32/Kconfig
@@ -32,4 +32,10 @@ config PINCTRL_STM32H743
 	depends on OF
 	default MACH_STM32H743
 	select PINCTRL_STM32
+
+config PINCTRL_STM32MP157
+	bool "STMicroelectronics STM32MP157 pin control" if COMPILE_TEST && !MACH_STM32MP157
+	depends on OF
+	default MACH_STM32MP157
+	select PINCTRL_STM32
 endif
diff --git a/drivers/pinctrl/stm32/Makefile b/drivers/pinctrl/stm32/Makefile
index d13ca35..b52223d 100644
--- a/drivers/pinctrl/stm32/Makefile
+++ b/drivers/pinctrl/stm32/Makefile
@@ -7,3 +7,4 @@ obj-$(CONFIG_PINCTRL_STM32F429)	+= pinctrl-stm32f429.o
 obj-$(CONFIG_PINCTRL_STM32F469)	+= pinctrl-stm32f469.o
 obj-$(CONFIG_PINCTRL_STM32F746)	+= pinctrl-stm32f746.o
 obj-$(CONFIG_PINCTRL_STM32H743)	+= pinctrl-stm32h743.o
+obj-$(CONFIG_PINCTRL_STM32MP157) += pinctrl-stm32mp157.o
diff --git a/drivers/pinctrl/stm32/pinctrl-stm32mp157.c b/drivers/pinctrl/stm32/pinctrl-stm32mp157.c
new file mode 100644
index 0000000..7c7d628
--- /dev/null
+++ b/drivers/pinctrl/stm32/pinctrl-stm32mp157.c
@@ -0,0 +1,2188 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+#include <linux/init.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-stm32.h"
+
+static const struct stm32_desc_pin stm32mp157_pins[] = {
+	STM32_PIN(
+		PINCTRL_PIN(0, "PA0"),
+		STM32_FUNCTION(0, "GPIOA0"),
+		STM32_FUNCTION(2, "TIM2_CH1 TIM2_ETR"),
+		STM32_FUNCTION(3, "TIM5_CH1"),
+		STM32_FUNCTION(4, "TIM8_ETR"),
+		STM32_FUNCTION(5, "TIM15_BKIN"),
+		STM32_FUNCTION(8, "USART2_CTS_NSS USART_BOOT2_CTS_NSS"),
+		STM32_FUNCTION(9, "UART4_TX"),
+		STM32_FUNCTION(10, "SDMMC2_CMD"),
+		STM32_FUNCTION(11, "SAI2_SD_B"),
+		STM32_FUNCTION(12, "ETH_GMII_CRS ETH_MII_CRS"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(1, "PA1"),
+		STM32_FUNCTION(0, "GPIOA1"),
+		STM32_FUNCTION(1, "ETH_CLK"),
+		STM32_FUNCTION(2, "TIM2_CH2"),
+		STM32_FUNCTION(3, "TIM5_CH2"),
+		STM32_FUNCTION(4, "LPTIM3_OUT"),
+		STM32_FUNCTION(5, "TIM15_CH1N"),
+		STM32_FUNCTION(8, "USART2_RTS USART_BOOT2_RTS"),
+		STM32_FUNCTION(9, "UART4_RX"),
+		STM32_FUNCTION(10, "QUADSPI_BK1_IO3 QUADSPI_BOOTBK1_IO3"),
+		STM32_FUNCTION(11, "SAI2_MCLK_B"),
+		STM32_FUNCTION(12, "ETH_GMII_RX_CLK ETH_MII_RX_CLK ETH_RGMII_RX_CLK ETH_RMII_REF_CLK"),
+		STM32_FUNCTION(15, "LCD_R2"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(2, "PA2"),
+		STM32_FUNCTION(0, "GPIOA2"),
+		STM32_FUNCTION(2, "TIM2_CH3"),
+		STM32_FUNCTION(3, "TIM5_CH3"),
+		STM32_FUNCTION(4, "LPTIM4_OUT"),
+		STM32_FUNCTION(5, "TIM15_CH1"),
+		STM32_FUNCTION(8, "USART2_TX USART_BOOT2_TX"),
+		STM32_FUNCTION(9, "SAI2_SCK_B"),
+		STM32_FUNCTION(11, "SDMMC2_D0DIR SDMMC_BOOT2_D0DIR"),
+		STM32_FUNCTION(12, "ETH_MDIO"),
+		STM32_FUNCTION(13, "MDIOS_MDIO"),
+		STM32_FUNCTION(15, "LCD_R1"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(3, "PA3"),
+		STM32_FUNCTION(0, "GPIOA3"),
+		STM32_FUNCTION(2, "TIM2_CH4"),
+		STM32_FUNCTION(3, "TIM5_CH4"),
+		STM32_FUNCTION(4, "LPTIM5_OUT"),
+		STM32_FUNCTION(5, "TIM15_CH2"),
+		STM32_FUNCTION(8, "USART2_RX USART_BOOT2_RX"),
+		STM32_FUNCTION(10, "LCD_B2"),
+		STM32_FUNCTION(12, "ETH_GMII_COL ETH_MII_COL"),
+		STM32_FUNCTION(15, "LCD_B5"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(4, "PA4"),
+		STM32_FUNCTION(0, "GPIOA4"),
+		STM32_FUNCTION(1, "HDP0"),
+		STM32_FUNCTION(3, "TIM5_ETR"),
+		STM32_FUNCTION(5, "SAI4_D2"),
+		STM32_FUNCTION(6, "SPI1_NSS I2S1_WS"),
+		STM32_FUNCTION(7, "SPI3_NSS I2S3_WS"),
+		STM32_FUNCTION(8, "USART2_CK USART_BOOT2_CK"),
+		STM32_FUNCTION(9, "SPI6_NSS"),
+		STM32_FUNCTION(13, "SAI4_FS_A"),
+		STM32_FUNCTION(14, "DCMI_HSYNC"),
+		STM32_FUNCTION(15, "LCD_VSYNC"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(5, "PA5"),
+		STM32_FUNCTION(0, "GPIOA5"),
+		STM32_FUNCTION(2, "TIM2_CH1 TIM2_ETR"),
+		STM32_FUNCTION(4, "TIM8_CH1N"),
+		STM32_FUNCTION(5, "SAI4_CK1"),
+		STM32_FUNCTION(6, "SPI1_SCK I2S1_CK"),
+		STM32_FUNCTION(9, "SPI6_SCK"),
+		STM32_FUNCTION(13, "SAI4_MCLK_A"),
+		STM32_FUNCTION(15, "LCD_R4"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(6, "PA6"),
+		STM32_FUNCTION(0, "GPIOA6"),
+		STM32_FUNCTION(2, "TIM1_BKIN"),
+		STM32_FUNCTION(3, "TIM3_CH1"),
+		STM32_FUNCTION(4, "TIM8_BKIN"),
+		STM32_FUNCTION(5, "SAI4_CK2"),
+		STM32_FUNCTION(6, "SPI1_MISO I2S1_SDI"),
+		STM32_FUNCTION(9, "SPI6_MISO"),
+		STM32_FUNCTION(10, "TIM13_CH1"),
+		STM32_FUNCTION(12, "MDIOS_MDC"),
+		STM32_FUNCTION(13, "SAI4_SCK_A"),
+		STM32_FUNCTION(14, "DCMI_PIXCLK"),
+		STM32_FUNCTION(15, "LCD_G2"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(7, "PA7"),
+		STM32_FUNCTION(0, "GPIOA7"),
+		STM32_FUNCTION(2, "TIM1_CH1N"),
+		STM32_FUNCTION(3, "TIM3_CH2"),
+		STM32_FUNCTION(4, "TIM8_CH1N"),
+		STM32_FUNCTION(5, "SAI4_D1"),
+		STM32_FUNCTION(6, "SPI1_MOSI I2S1_SDO"),
+		STM32_FUNCTION(9, "SPI6_MOSI"),
+		STM32_FUNCTION(10, "TIM14_CH1"),
+		STM32_FUNCTION(11, "QUADSPI_CLK"),
+		STM32_FUNCTION(12, "ETH_GMII_RX_DV ETH_MII_RX_DV ETH_RGMII_RX_CTL ETH_RMII_CRS_DV"),
+		STM32_FUNCTION(13, "SAI4_SD_A"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(8, "PA8"),
+		STM32_FUNCTION(0, "GPIOA8"),
+		STM32_FUNCTION(1, "MCO1"),
+		STM32_FUNCTION(2, "TIM1_CH1"),
+		STM32_FUNCTION(4, "TIM8_BKIN2"),
+		STM32_FUNCTION(5, "I2C3_SCL"),
+		STM32_FUNCTION(6, "SPI3_MOSI I2S3_SDO"),
+		STM32_FUNCTION(8, "USART1_CK"),
+		STM32_FUNCTION(9, "SDMMC2_CKIN SDMMC_BOOT2_CKIN"),
+		STM32_FUNCTION(10, "SDMMC2_D4 SDMMC_BOOT2_D4"),
+		STM32_FUNCTION(11, "USBO_SOF"),
+		STM32_FUNCTION(13, "SAI4_SD_B"),
+		STM32_FUNCTION(14, "UART7_RX"),
+		STM32_FUNCTION(15, "LCD_R6"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(9, "PA9"),
+		STM32_FUNCTION(0, "GPIOA9"),
+		STM32_FUNCTION(2, "TIM1_CH2"),
+		STM32_FUNCTION(5, "I2C3_SMBA"),
+		STM32_FUNCTION(6, "SPI2_SCK I2S2_CK"),
+		STM32_FUNCTION(8, "USART1_TX"),
+		STM32_FUNCTION(9, "SDMMC2_CDIR SDMMC_BOOT2_CDIR"),
+		STM32_FUNCTION(10, "CAN1_RXFD"),
+		STM32_FUNCTION(11, "SDMMC2_D5 SDMMC_BOOT2_D5"),
+		STM32_FUNCTION(14, "DCMI_D0"),
+		STM32_FUNCTION(15, "LCD_R5"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(10, "PA10"),
+		STM32_FUNCTION(0, "GPIOA10"),
+		STM32_FUNCTION(2, "TIM1_CH3"),
+		STM32_FUNCTION(6, "SPI3_NSS I2S3_WS"),
+		STM32_FUNCTION(8, "USART1_RX"),
+		STM32_FUNCTION(10, "CAN1_TXFD"),
+		STM32_FUNCTION(12, "MDIOS_MDIO"),
+		STM32_FUNCTION(13, "SAI4_FS_B"),
+		STM32_FUNCTION(14, "DCMI_D1"),
+		STM32_FUNCTION(15, "LCD_B1"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(11, "PA11"),
+		STM32_FUNCTION(0, "GPIOA11"),
+		STM32_FUNCTION(2, "TIM1_CH4"),
+		STM32_FUNCTION(3, "I2C6_SCL"),
+		STM32_FUNCTION(5, "I2C5_SCL"),
+		STM32_FUNCTION(6, "SPI2_NSS I2S2_WS"),
+		STM32_FUNCTION(7, "UART4_RX"),
+		STM32_FUNCTION(8, "USART1_CTS_NSS"),
+		STM32_FUNCTION(10, "CAN1_RX"),
+		STM32_FUNCTION(15, "LCD_R4"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(12, "PA12"),
+		STM32_FUNCTION(0, "GPIOA12"),
+		STM32_FUNCTION(2, "TIM1_ETR"),
+		STM32_FUNCTION(3, "I2C6_SDA"),
+		STM32_FUNCTION(5, "I2C5_SDA"),
+		STM32_FUNCTION(6, "SPI2_SCK I2S2_CK"),
+		STM32_FUNCTION(7, "UART4_TX"),
+		STM32_FUNCTION(8, "USART1_RTS"),
+		STM32_FUNCTION(9, "SAI2_FS_B"),
+		STM32_FUNCTION(10, "CAN1_TX"),
+		STM32_FUNCTION(15, "LCD_R5"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(13, "PA13"),
+		STM32_FUNCTION(0, "GPIOA13"),
+		STM32_FUNCTION(1, "DBTRGO"),
+		STM32_FUNCTION(2, "DBTRGI"),
+		STM32_FUNCTION(3, "MCO1"),
+		STM32_FUNCTION(9, "UART4_TX"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(14, "PA14"),
+		STM32_FUNCTION(0, "GPIOA14"),
+		STM32_FUNCTION(1, "DBTRGO"),
+		STM32_FUNCTION(2, "DBTRGI"),
+		STM32_FUNCTION(3, "MCO2"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(15, "PA15"),
+		STM32_FUNCTION(0, "GPIOA15"),
+		STM32_FUNCTION(1, "DBTRGI"),
+		STM32_FUNCTION(2, "TIM2_CH1 TIM2_ETR"),
+		STM32_FUNCTION(3, "SAI4_D2"),
+		STM32_FUNCTION(4, "SDMMC1_CDIR"),
+		STM32_FUNCTION(5, "HDMI_CEC"),
+		STM32_FUNCTION(6, "SPI1_NSS I2S1_WS"),
+		STM32_FUNCTION(7, "SPI3_NSS I2S3_WS"),
+		STM32_FUNCTION(8, "SPI6_NSS"),
+		STM32_FUNCTION(9, "UART4_RTS UART_BOOT4_RTS"),
+		STM32_FUNCTION(10, "SDMMC2_D5 SDMMC_BOOT2_D5"),
+		STM32_FUNCTION(11, "SDMMC2_CDIR SDMMC_BOOT2_CDIR"),
+		STM32_FUNCTION(12, "SDMMC1_D5 SDMMC_BOOT1_D5"),
+		STM32_FUNCTION(13, "SAI4_FS_A"),
+		STM32_FUNCTION(14, "UART7_TX"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(16, "PB0"),
+		STM32_FUNCTION(0, "GPIOB0"),
+		STM32_FUNCTION(2, "TIM1_CH2N"),
+		STM32_FUNCTION(3, "TIM3_CH3"),
+		STM32_FUNCTION(4, "TIM8_CH2N"),
+		STM32_FUNCTION(7, "DFSDM_CKOUT"),
+		STM32_FUNCTION(9, "UART4_CTS UART_BOOT4_CTS"),
+		STM32_FUNCTION(10, "LCD_R3"),
+		STM32_FUNCTION(12, "ETH_GMII_RXD2 ETH_MII_RXD2 ETH_RGMII_RXD2"),
+		STM32_FUNCTION(13, "MDIOS_MDIO"),
+		STM32_FUNCTION(15, "LCD_G1"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(17, "PB1"),
+		STM32_FUNCTION(0, "GPIOB1"),
+		STM32_FUNCTION(2, "TIM1_CH3N"),
+		STM32_FUNCTION(3, "TIM3_CH4"),
+		STM32_FUNCTION(4, "TIM8_CH3N"),
+		STM32_FUNCTION(7, "DFSDM_DATA1"),
+		STM32_FUNCTION(10, "LCD_R6"),
+		STM32_FUNCTION(12, "ETH_GMII_RXD3 ETH_MII_RXD3 ETH_RGMII_RXD3"),
+		STM32_FUNCTION(13, "MDIOS_MDC"),
+		STM32_FUNCTION(15, "LCD_G0"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(18, "PB2"),
+		STM32_FUNCTION(0, "GPIOB2"),
+		STM32_FUNCTION(1, "TRACED4"),
+		STM32_FUNCTION(2, "RTC_OUT2"),
+		STM32_FUNCTION(3, "SAI1_D1"),
+		STM32_FUNCTION(4, "DFSDM_CK1"),
+		STM32_FUNCTION(5, "USART1_RX"),
+		STM32_FUNCTION(6, "I2S_CKIN"),
+		STM32_FUNCTION(7, "SAI1_SD_A"),
+		STM32_FUNCTION(8, "SPI3_MOSI I2S3_SDO"),
+		STM32_FUNCTION(9, "UART4_RX UART_BOOT4_RX"),
+		STM32_FUNCTION(10, "QUADSPI_CLK"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(19, "PB3"),
+		STM32_FUNCTION(0, "GPIOB3"),
+		STM32_FUNCTION(1, "TRACED9"),
+		STM32_FUNCTION(2, "TIM2_CH2"),
+		STM32_FUNCTION(5, "SAI4_CK1"),
+		STM32_FUNCTION(6, "SPI1_SCK I2S1_CK"),
+		STM32_FUNCTION(7, "SPI3_SCK I2S3_CK"),
+		STM32_FUNCTION(9, "SPI6_SCK"),
+		STM32_FUNCTION(10, "SDMMC2_D2 SDMMC_BOOT2_D2"),
+		STM32_FUNCTION(13, "SAI4_MCLK_A"),
+		STM32_FUNCTION(14, "UART7_RX"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(20, "PB4"),
+		STM32_FUNCTION(0, "GPIOB4"),
+		STM32_FUNCTION(1, "TRACED8"),
+		STM32_FUNCTION(2, "TIM16_BKIN"),
+		STM32_FUNCTION(3, "TIM3_CH1"),
+		STM32_FUNCTION(5, "SAI4_CK2"),
+		STM32_FUNCTION(6, "SPI1_MISO I2S1_SDI"),
+		STM32_FUNCTION(7, "SPI3_MISO I2S3_SDI"),
+		STM32_FUNCTION(8, "SPI2_NSS I2S2_WS"),
+		STM32_FUNCTION(9, "SPI6_MISO"),
+		STM32_FUNCTION(10, "SDMMC2_D3 SDMMC_BOOT2_D3"),
+		STM32_FUNCTION(13, "SAI4_SCK_A"),
+		STM32_FUNCTION(14, "UART7_TX"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(21, "PB5"),
+		STM32_FUNCTION(0, "GPIOB5"),
+		STM32_FUNCTION(1, "ETH_CLK"),
+		STM32_FUNCTION(2, "TIM17_BKIN"),
+		STM32_FUNCTION(3, "TIM3_CH2"),
+		STM32_FUNCTION(4, "SAI4_D1"),
+		STM32_FUNCTION(5, "I2C1_SMBA"),
+		STM32_FUNCTION(6, "SPI1_MOSI I2S1_SDO"),
+		STM32_FUNCTION(7, "I2C4_SMBA"),
+		STM32_FUNCTION(8, "SPI3_MOSI I2S3_SDO"),
+		STM32_FUNCTION(9, "SPI6_MOSI"),
+		STM32_FUNCTION(10, "CAN2_RX"),
+		STM32_FUNCTION(11, "SAI4_SD_A"),
+		STM32_FUNCTION(12, "ETH_PPS_OUT"),
+		STM32_FUNCTION(13, "UART5_RX UART_BOOT5_RX"),
+		STM32_FUNCTION(14, "DCMI_D10"),
+		STM32_FUNCTION(15, "LCD_G7"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(22, "PB6"),
+		STM32_FUNCTION(0, "GPIOB6"),
+		STM32_FUNCTION(2, "TIM16_CH1N"),
+		STM32_FUNCTION(3, "TIM4_CH1"),
+		STM32_FUNCTION(5, "I2C1_SCL"),
+		STM32_FUNCTION(6, "HDMI_CEC"),
+		STM32_FUNCTION(7, "I2C4_SCL"),
+		STM32_FUNCTION(8, "USART1_TX"),
+		STM32_FUNCTION(10, "CAN2_TX"),
+		STM32_FUNCTION(11, "QUADSPI_BK1_NCS QUADSPI_BOOTBK1_NCS"),
+		STM32_FUNCTION(12, "DFSDM_DATA5"),
+		STM32_FUNCTION(13, "UART5_TX"),
+		STM32_FUNCTION(14, "DCMI_D5"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(23, "PB7"),
+		STM32_FUNCTION(0, "GPIOB7"),
+		STM32_FUNCTION(2, "TIM17_CH1N"),
+		STM32_FUNCTION(3, "TIM4_CH2"),
+		STM32_FUNCTION(5, "I2C1_SDA"),
+		STM32_FUNCTION(7, "I2C4_SDA"),
+		STM32_FUNCTION(8, "USART1_RX"),
+		STM32_FUNCTION(10, "CAN2_TXFD"),
+		STM32_FUNCTION(11, "SDMMC2_D1 SDMMC_BOOT2_D1"),
+		STM32_FUNCTION(12, "DFSDM_CK5"),
+		STM32_FUNCTION(13, "FMC_NL"),
+		STM32_FUNCTION(14, "DCMI_VSYNC"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(24, "PB8"),
+		STM32_FUNCTION(0, "GPIOB8"),
+		STM32_FUNCTION(1, "HDP6"),
+		STM32_FUNCTION(2, "TIM16_CH1"),
+		STM32_FUNCTION(3, "TIM4_CH3"),
+		STM32_FUNCTION(4, "DFSDM_CK7"),
+		STM32_FUNCTION(5, "I2C1_SCL"),
+		STM32_FUNCTION(6, "SDMMC1_CKIN SDMMC_BOOT1_CKIN"),
+		STM32_FUNCTION(7, "I2C4_SCL"),
+		STM32_FUNCTION(8, "SDMMC2_CKIN SDMMC_BOOT2_CKIN"),
+		STM32_FUNCTION(9, "UART4_RX"),
+		STM32_FUNCTION(10, "CAN1_RX"),
+		STM32_FUNCTION(11, "SDMMC2_D4 SDMMC_BOOT2_D4"),
+		STM32_FUNCTION(12, "ETH_GMII_TXD3 ETH_MII_TXD3 ETH_RGMII_TXD3"),
+		STM32_FUNCTION(13, "SDMMC1_D4 SDMMC_BOOT1_D4"),
+		STM32_FUNCTION(14, "DCMI_D6"),
+		STM32_FUNCTION(15, "LCD_B6"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(25, "PB9"),
+		STM32_FUNCTION(0, "GPIOB9"),
+		STM32_FUNCTION(1, "HDP7"),
+		STM32_FUNCTION(2, "TIM17_CH1"),
+		STM32_FUNCTION(3, "TIM4_CH4"),
+		STM32_FUNCTION(4, "DFSDM_DATA7"),
+		STM32_FUNCTION(5, "I2C1_SDA"),
+		STM32_FUNCTION(6, "SPI2_NSS I2S2_WS"),
+		STM32_FUNCTION(7, "I2C4_SDA"),
+		STM32_FUNCTION(8, "SDMMC2_CDIR SDMMC_BOOT2_CDIR"),
+		STM32_FUNCTION(9, "UART4_TX"),
+		STM32_FUNCTION(10, "CAN1_TX"),
+		STM32_FUNCTION(11, "SDMMC2_D5 SDMMC_BOOT2_D5"),
+		STM32_FUNCTION(12, "SDMMC1_CDIR SDMMC_BOOT1_CDIR"),
+		STM32_FUNCTION(13, "SDMMC1_D5 SDMMC_BOOT1_D5"),
+		STM32_FUNCTION(14, "DCMI_D7"),
+		STM32_FUNCTION(15, "LCD_B7"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(26, "PB10"),
+		STM32_FUNCTION(0, "GPIOB10"),
+		STM32_FUNCTION(2, "TIM2_CH3"),
+		STM32_FUNCTION(4, "LPTIM2_IN1"),
+		STM32_FUNCTION(5, "I2C2_SCL"),
+		STM32_FUNCTION(6, "SPI2_SCK I2S2_CK"),
+		STM32_FUNCTION(7, "DFSDM_DATA7"),
+		STM32_FUNCTION(8, "USART3_TX USART_BOOT3_TX"),
+		STM32_FUNCTION(10, "QUADSPI_BK1_NCS"),
+		STM32_FUNCTION(12, "ETH_GMII_RX_ER ETH_MII_RX_ER"),
+		STM32_FUNCTION(15, "LCD_G4"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(27, "PB11"),
+		STM32_FUNCTION(0, "GPIOB11"),
+		STM32_FUNCTION(2, "TIM2_CH4"),
+		STM32_FUNCTION(4, "LPTIM2_ETR"),
+		STM32_FUNCTION(5, "I2C2_SDA"),
+		STM32_FUNCTION(7, "DFSDM_CK7"),
+		STM32_FUNCTION(8, "USART3_RX"),
+		STM32_FUNCTION(12, "ETH_GMII_TX_EN ETH_MII_TX_EN ETH_RGMII_TX_CTL ETH_RMII_TX_EN"),
+		STM32_FUNCTION(14, "DSI_TE"),
+		STM32_FUNCTION(15, "LCD_G5"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(28, "PB12"),
+		STM32_FUNCTION(0, "GPIOB12"),
+		STM32_FUNCTION(2, "TIM1_BKIN"),
+		STM32_FUNCTION(3, "I2C6_SMBA"),
+		STM32_FUNCTION(5, "I2C2_SMBA"),
+		STM32_FUNCTION(6, "SPI2_NSS I2S2_WS"),
+		STM32_FUNCTION(7, "DFSDM_DATA1"),
+		STM32_FUNCTION(8, "USART3_CK USART_BOOT3_CK"),
+		STM32_FUNCTION(9, "USART3_RX USART_BOOT3_RX"),
+		STM32_FUNCTION(10, "CAN2_RX"),
+		STM32_FUNCTION(12, "ETH_GMII_TXD0 ETH_MII_TXD0 ETH_RGMII_TXD0 ETH_RMII_TXD0"),
+		STM32_FUNCTION(15, "UART5_RX"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(29, "PB13"),
+		STM32_FUNCTION(0, "GPIOB13"),
+		STM32_FUNCTION(2, "TIM1_CH1N"),
+		STM32_FUNCTION(4, "DFSDM_CKOUT"),
+		STM32_FUNCTION(5, "LPTIM2_OUT"),
+		STM32_FUNCTION(6, "SPI2_SCK I2S2_CK"),
+		STM32_FUNCTION(7, "DFSDM_CK1"),
+		STM32_FUNCTION(8, "USART3_CTS_NSS USART_BOOT3_CTS_NSS"),
+		STM32_FUNCTION(10, "CAN2_TX"),
+		STM32_FUNCTION(12, "ETH_GMII_TXD1 ETH_MII_TXD1 ETH_RGMII_TXD1 ETH_RMII_TXD1"),
+		STM32_FUNCTION(15, "UART5_TX UART_BOOT5_TX"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(30, "PB14"),
+		STM32_FUNCTION(0, "GPIOB14"),
+		STM32_FUNCTION(2, "TIM1_CH2N"),
+		STM32_FUNCTION(3, "TIM12_CH1"),
+		STM32_FUNCTION(4, "TIM8_CH2N"),
+		STM32_FUNCTION(5, "USART1_TX"),
+		STM32_FUNCTION(6, "SPI2_MISO I2S2_SDI"),
+		STM32_FUNCTION(7, "DFSDM_DATA2"),
+		STM32_FUNCTION(8, "USART3_RTS USART_BOOT3_RTS"),
+		STM32_FUNCTION(10, "SDMMC2_D0 SDMMC_BOOT2_D0"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(31, "PB15"),
+		STM32_FUNCTION(0, "GPIOB15"),
+		STM32_FUNCTION(1, "RTC_REFIN"),
+		STM32_FUNCTION(2, "TIM1_CH3N"),
+		STM32_FUNCTION(3, "TIM12_CH2"),
+		STM32_FUNCTION(4, "TIM8_CH3N"),
+		STM32_FUNCTION(5, "USART1_RX"),
+		STM32_FUNCTION(6, "SPI2_MOSI I2S2_SDO"),
+		STM32_FUNCTION(7, "DFSDM_CK2"),
+		STM32_FUNCTION(10, "SDMMC2_D1 SDMMC_BOOT2_D1"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(32, "PC0"),
+		STM32_FUNCTION(0, "GPIOC0"),
+		STM32_FUNCTION(4, "DFSDM_CK0"),
+		STM32_FUNCTION(5, "LPTIM2_IN2"),
+		STM32_FUNCTION(7, "DFSDM_DATA4"),
+		STM32_FUNCTION(9, "SAI2_FS_B"),
+		STM32_FUNCTION(11, "QUADSPI_BK2_NCS QUADSPI_BOOTBK2_NCS"),
+		STM32_FUNCTION(15, "LCD_R5"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(33, "PC1"),
+		STM32_FUNCTION(0, "GPIOC1"),
+		STM32_FUNCTION(1, "TRACED0"),
+		STM32_FUNCTION(3, "SAI1_D1"),
+		STM32_FUNCTION(4, "DFSDM_DATA0"),
+		STM32_FUNCTION(5, "DFSDM_CK4"),
+		STM32_FUNCTION(6, "SPI2_MOSI I2S2_SDO"),
+		STM32_FUNCTION(7, "SAI1_SD_A"),
+		STM32_FUNCTION(10, "SDMMC2_CK"),
+		STM32_FUNCTION(12, "ETH_MDC"),
+		STM32_FUNCTION(13, "MDIOS_MDC"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(34, "PC2"),
+		STM32_FUNCTION(0, "GPIOC2"),
+		STM32_FUNCTION(4, "DFSDM_CK1"),
+		STM32_FUNCTION(6, "SPI2_MISO I2S2_SDI"),
+		STM32_FUNCTION(7, "DFSDM_CKOUT"),
+		STM32_FUNCTION(12, "ETH_GMII_TXD2 ETH_MII_TXD2 ETH_RGMII_TXD2"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(35, "PC3"),
+		STM32_FUNCTION(0, "GPIOC3"),
+		STM32_FUNCTION(1, "TRACECLK"),
+		STM32_FUNCTION(4, "DFSDM_DATA1"),
+		STM32_FUNCTION(6, "SPI2_MOSI I2S2_SDO"),
+		STM32_FUNCTION(12, "ETH_GMII_TX_CLK ETH_MII_TX_CLK"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(36, "PC4"),
+		STM32_FUNCTION(0, "GPIOC4"),
+		STM32_FUNCTION(4, "DFSDM_CK2"),
+		STM32_FUNCTION(6, "I2S1_MCK"),
+		STM32_FUNCTION(10, "SPDIF_IN2"),
+		STM32_FUNCTION(12, "ETH_GMII_RXD0 ETH_MII_RXD0 ETH_RGMII_RXD0 ETH_RMII_RXD0"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(37, "PC5"),
+		STM32_FUNCTION(0, "GPIOC5"),
+		STM32_FUNCTION(3, "SAI1_D3"),
+		STM32_FUNCTION(4, "DFSDM_DATA2"),
+		STM32_FUNCTION(5, "SAI4_D4"),
+		STM32_FUNCTION(7, "SAI1_D4"),
+		STM32_FUNCTION(10, "SPDIF_IN3"),
+		STM32_FUNCTION(12, "ETH_GMII_RXD1 ETH_MII_RXD1 ETH_RGMII_RXD1 ETH_RMII_RXD1"),
+		STM32_FUNCTION(13, "SAI4_D3"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(38, "PC6"),
+		STM32_FUNCTION(0, "GPIOC6"),
+		STM32_FUNCTION(1, "HDP1"),
+		STM32_FUNCTION(3, "TIM3_CH1"),
+		STM32_FUNCTION(4, "TIM8_CH1"),
+		STM32_FUNCTION(5, "DFSDM_CK3"),
+		STM32_FUNCTION(6, "I2S2_MCK"),
+		STM32_FUNCTION(8, "USART6_TX USART_BOOT6_TX"),
+		STM32_FUNCTION(9, "SDMMC1_D0DIR SDMMC_BOOT1_D0DIR"),
+		STM32_FUNCTION(10, "SDMMC2_D0DIR SDMMC_BOOT2_D0DIR"),
+		STM32_FUNCTION(11, "SDMMC2_D6 SDMMC_BOOT2_D6"),
+		STM32_FUNCTION(12, "DSI_TE"),
+		STM32_FUNCTION(13, "SDMMC1_D6 SDMMC_BOOT1_D6"),
+		STM32_FUNCTION(14, "DCMI_D0"),
+		STM32_FUNCTION(15, "LCD_HSYNC"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(39, "PC7"),
+		STM32_FUNCTION(0, "GPIOC7"),
+		STM32_FUNCTION(1, "HDP4"),
+		STM32_FUNCTION(3, "TIM3_CH2"),
+		STM32_FUNCTION(4, "TIM8_CH2"),
+		STM32_FUNCTION(5, "DFSDM_DATA3"),
+		STM32_FUNCTION(7, "I2S3_MCK"),
+		STM32_FUNCTION(8, "USART6_RX USART_BOOT6_RX"),
+		STM32_FUNCTION(9, "SDMMC1_D123DIR SDMMC_BOOT1_D123DIR"),
+		STM32_FUNCTION(10, "SDMMC2_D123DIR SDMMC_BOOT2_D123DIR"),
+		STM32_FUNCTION(11, "SDMMC2_D7 SDMMC_BOOT2_D7"),
+		STM32_FUNCTION(13, "SDMMC1_D7 SDMMC_BOOT1_D7"),
+		STM32_FUNCTION(14, "DCMI_D1"),
+		STM32_FUNCTION(15, "LCD_G6"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(40, "PC8"),
+		STM32_FUNCTION(0, "GPIOC8"),
+		STM32_FUNCTION(1, "TRACED0"),
+		STM32_FUNCTION(3, "TIM3_CH3"),
+		STM32_FUNCTION(4, "TIM8_CH3"),
+		STM32_FUNCTION(7, "UART4_TX"),
+		STM32_FUNCTION(8, "USART6_CK USART_BOOT6_CK"),
+		STM32_FUNCTION(9, "UART5_RTS UART_BOOT5_RTS"),
+		STM32_FUNCTION(13, "SDMMC1_D0 SDMMC_BOOT1_D0"),
+		STM32_FUNCTION(14, "DCMI_D2"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(41, "PC9"),
+		STM32_FUNCTION(0, "GPIOC9"),
+		STM32_FUNCTION(1, "TRACED1"),
+		STM32_FUNCTION(3, "TIM3_CH4"),
+		STM32_FUNCTION(4, "TIM8_CH4"),
+		STM32_FUNCTION(5, "I2C3_SDA"),
+		STM32_FUNCTION(6, "I2S_CKIN"),
+		STM32_FUNCTION(9, "UART5_CTS UART_BOOT5_CTS"),
+		STM32_FUNCTION(10, "QUADSPI_BK1_IO0"),
+		STM32_FUNCTION(13, "SDMMC1_D1 SDMMC_BOOT1_D1"),
+		STM32_FUNCTION(14, "DCMI_D3"),
+		STM32_FUNCTION(15, "LCD_B2"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(42, "PC10"),
+		STM32_FUNCTION(0, "GPIOC10"),
+		STM32_FUNCTION(1, "TRACED2"),
+		STM32_FUNCTION(4, "DFSDM_CK5"),
+		STM32_FUNCTION(7, "SPI3_SCK I2S3_CK"),
+		STM32_FUNCTION(8, "USART3_TX"),
+		STM32_FUNCTION(9, "UART4_TX"),
+		STM32_FUNCTION(10, "QUADSPI_BK1_IO1"),
+		STM32_FUNCTION(11, "SAI4_MCLK_B"),
+		STM32_FUNCTION(13, "SDMMC1_D2 SDMMC_BOOT1_D2"),
+		STM32_FUNCTION(14, "DCMI_D8"),
+		STM32_FUNCTION(15, "LCD_R2"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(43, "PC11"),
+		STM32_FUNCTION(0, "GPIOC11"),
+		STM32_FUNCTION(1, "TRACED3"),
+		STM32_FUNCTION(4, "DFSDM_DATA5"),
+		STM32_FUNCTION(7, "SPI3_MISO I2S3_SDI"),
+		STM32_FUNCTION(8, "USART3_RX"),
+		STM32_FUNCTION(9, "UART4_RX"),
+		STM32_FUNCTION(10, "QUADSPI_BK2_NCS QUADSPI_BOOTBK2_NCS"),
+		STM32_FUNCTION(11, "SAI4_SCK_B"),
+		STM32_FUNCTION(13, "SDMMC1_D3 SDMMC_BOOT1_D3"),
+		STM32_FUNCTION(14, "DCMI_D4"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(44, "PC12"),
+		STM32_FUNCTION(0, "GPIOC12"),
+		STM32_FUNCTION(1, "TRACECLK"),
+		STM32_FUNCTION(2, "MCO2"),
+		STM32_FUNCTION(3, "SAI4_D3"),
+		STM32_FUNCTION(7, "SPI3_MOSI I2S3_SDO"),
+		STM32_FUNCTION(8, "USART3_CK USART_BOOT3_CK"),
+		STM32_FUNCTION(9, "UART5_TX"),
+		STM32_FUNCTION(11, "SAI4_SD_B"),
+		STM32_FUNCTION(13, "SDMMC1_CK SDMMC_BOOT1_CK"),
+		STM32_FUNCTION(14, "DCMI_D9"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(45, "PC13"),
+		STM32_FUNCTION(0, "GPIOC13"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(46, "PC14"),
+		STM32_FUNCTION(0, "GPIOC14"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(47, "PC15"),
+		STM32_FUNCTION(0, "GPIOC15"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(48, "PD0"),
+		STM32_FUNCTION(0, "GPIOD0"),
+		STM32_FUNCTION(3, "I2C6_SDA"),
+		STM32_FUNCTION(4, "DFSDM_CK6"),
+		STM32_FUNCTION(5, "I2C5_SDA"),
+		STM32_FUNCTION(7, "SAI3_SCK_A"),
+		STM32_FUNCTION(9, "UART4_RX"),
+		STM32_FUNCTION(10, "CAN1_RX"),
+		STM32_FUNCTION(11, "SDMMC3_CMD"),
+		STM32_FUNCTION(12, "DFSDM_DATA7"),
+		STM32_FUNCTION(13, "FMC_D2"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(49, "PD1"),
+		STM32_FUNCTION(0, "GPIOD1"),
+		STM32_FUNCTION(3, "I2C6_SCL"),
+		STM32_FUNCTION(4, "DFSDM_DATA6"),
+		STM32_FUNCTION(5, "I2C5_SCL"),
+		STM32_FUNCTION(7, "SAI3_SD_A"),
+		STM32_FUNCTION(9, "UART4_TX"),
+		STM32_FUNCTION(10, "CAN1_TX"),
+		STM32_FUNCTION(11, "SDMMC3_D0"),
+		STM32_FUNCTION(12, "DFSDM_CK7"),
+		STM32_FUNCTION(13, "FMC_D3"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(50, "PD2"),
+		STM32_FUNCTION(0, "GPIOD2"),
+		STM32_FUNCTION(3, "TIM3_ETR"),
+		STM32_FUNCTION(5, "I2C5_SMBA"),
+		STM32_FUNCTION(7, "UART4_RX"),
+		STM32_FUNCTION(9, "UART5_RX"),
+		STM32_FUNCTION(13, "SDMMC1_CMD SDMMC_BOOT1_CMD"),
+		STM32_FUNCTION(14, "DCMI_D11"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(51, "PD3"),
+		STM32_FUNCTION(0, "GPIOD3"),
+		STM32_FUNCTION(1, "HDP5"),
+		STM32_FUNCTION(4, "DFSDM_CKOUT"),
+		STM32_FUNCTION(6, "SPI2_SCK I2S2_CK"),
+		STM32_FUNCTION(7, "DFSDM_DATA0"),
+		STM32_FUNCTION(8, "USART2_CTS_NSS USART_BOOT2_CTS_NSS"),
+		STM32_FUNCTION(9, "SDMMC1_D123DIR SDMMC_BOOT1_D123DIR"),
+		STM32_FUNCTION(10, "SDMMC2_D7 SDMMC_BOOT2_D7"),
+		STM32_FUNCTION(11, "SDMMC2_D123DIR SDMMC_BOOT2_D123DIR"),
+		STM32_FUNCTION(12, "SDMMC1_D7 SDMMC_BOOT1_D7"),
+		STM32_FUNCTION(13, "FMC_CLK"),
+		STM32_FUNCTION(14, "DCMI_D5"),
+		STM32_FUNCTION(15, "LCD_G7"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(52, "PD4"),
+		STM32_FUNCTION(0, "GPIOD4"),
+		STM32_FUNCTION(7, "SAI3_FS_A"),
+		STM32_FUNCTION(8, "USART2_RTS USART_BOOT2_RTS"),
+		STM32_FUNCTION(10, "CAN1_RXFD"),
+		STM32_FUNCTION(11, "SDMMC3_D1"),
+		STM32_FUNCTION(12, "DFSDM_CK0"),
+		STM32_FUNCTION(13, "FMC_NOE"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(53, "PD5"),
+		STM32_FUNCTION(0, "GPIOD5"),
+		STM32_FUNCTION(8, "USART2_TX"),
+		STM32_FUNCTION(10, "CAN1_TXFD"),
+		STM32_FUNCTION(11, "SDMMC3_D2"),
+		STM32_FUNCTION(13, "FMC_NWE"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(54, "PD6"),
+		STM32_FUNCTION(0, "GPIOD6"),
+		STM32_FUNCTION(2, "TIM16_CH1N"),
+		STM32_FUNCTION(3, "SAI1_D1"),
+		STM32_FUNCTION(4, "DFSDM_CK4"),
+		STM32_FUNCTION(5, "DFSDM_DATA1"),
+		STM32_FUNCTION(6, "SPI3_MOSI I2S3_SDO"),
+		STM32_FUNCTION(7, "SAI1_SD_A"),
+		STM32_FUNCTION(8, "USART2_RX"),
+		STM32_FUNCTION(10, "CAN2_RXFD"),
+		STM32_FUNCTION(11, "FMC_INT"),
+		STM32_FUNCTION(13, "FMC_NWAIT"),
+		STM32_FUNCTION(14, "DCMI_D10"),
+		STM32_FUNCTION(15, "LCD_B2"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(55, "PD7"),
+		STM32_FUNCTION(0, "GPIOD7"),
+		STM32_FUNCTION(1, "TRACED6"),
+		STM32_FUNCTION(4, "DFSDM_DATA4"),
+		STM32_FUNCTION(5, "I2C2_SCL"),
+		STM32_FUNCTION(7, "DFSDM_CK1"),
+		STM32_FUNCTION(8, "USART2_CK USART_BOOT2_CK"),
+		STM32_FUNCTION(10, "SPDIF_IN0"),
+		STM32_FUNCTION(11, "SDMMC3_D3"),
+		STM32_FUNCTION(13, "FMC_NE1"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(56, "PD8"),
+		STM32_FUNCTION(0, "GPIOD8"),
+		STM32_FUNCTION(4, "DFSDM_CK3"),
+		STM32_FUNCTION(7, "SAI3_SCK_B"),
+		STM32_FUNCTION(8, "USART3_TX"),
+		STM32_FUNCTION(10, "SPDIF_IN1"),
+		STM32_FUNCTION(13, "FMC_D13"),
+		STM32_FUNCTION(15, "LCD_B7"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(57, "PD9"),
+		STM32_FUNCTION(0, "GPIOD9"),
+		STM32_FUNCTION(4, "DFSDM_DATA3"),
+		STM32_FUNCTION(7, "SAI3_SD_B"),
+		STM32_FUNCTION(8, "USART3_RX"),
+		STM32_FUNCTION(10, "CAN2_RXFD"),
+		STM32_FUNCTION(13, "FMC_D14"),
+		STM32_FUNCTION(15, "LCD_B0"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(58, "PD10"),
+		STM32_FUNCTION(0, "GPIOD10"),
+		STM32_FUNCTION(1, "RTC_REFIN"),
+		STM32_FUNCTION(2, "TIM16_BKIN"),
+		STM32_FUNCTION(4, "DFSDM_CKOUT"),
+		STM32_FUNCTION(5, "I2C5_SMBA"),
+		STM32_FUNCTION(6, "SPI3_MISO I2S3_SDI"),
+		STM32_FUNCTION(7, "SAI3_FS_B"),
+		STM32_FUNCTION(8, "USART3_CK USART_BOOT3_CK"),
+		STM32_FUNCTION(10, "CAN2_TXFD"),
+		STM32_FUNCTION(13, "FMC_D15"),
+		STM32_FUNCTION(15, "LCD_B3"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(59, "PD11"),
+		STM32_FUNCTION(0, "GPIOD11"),
+		STM32_FUNCTION(4, "LPTIM2_IN2"),
+		STM32_FUNCTION(5, "I2C4_SMBA"),
+		STM32_FUNCTION(6, "I2C1_SMBA"),
+		STM32_FUNCTION(8, "USART3_CTS_NSS USART_BOOT3_CTS_NSS"),
+		STM32_FUNCTION(10, "QUADSPI_BK1_IO0"),
+		STM32_FUNCTION(11, "SAI2_SD_A"),
+		STM32_FUNCTION(13, "FMC_A16 FMC_CLE"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(60, "PD12"),
+		STM32_FUNCTION(0, "GPIOD12"),
+		STM32_FUNCTION(2, "LPTIM1_IN1"),
+		STM32_FUNCTION(3, "TIM4_CH1"),
+		STM32_FUNCTION(4, "LPTIM2_IN1"),
+		STM32_FUNCTION(5, "I2C4_SCL"),
+		STM32_FUNCTION(6, "I2C1_SCL"),
+		STM32_FUNCTION(8, "USART3_RTS USART_BOOT3_RTS"),
+		STM32_FUNCTION(10, "QUADSPI_BK1_IO1"),
+		STM32_FUNCTION(11, "SAI2_FS_A"),
+		STM32_FUNCTION(13, "FMC_A17 FMC_ALE"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(61, "PD13"),
+		STM32_FUNCTION(0, "GPIOD13"),
+		STM32_FUNCTION(2, "LPTIM1_OUT"),
+		STM32_FUNCTION(3, "TIM4_CH2"),
+		STM32_FUNCTION(5, "I2C4_SDA"),
+		STM32_FUNCTION(6, "I2C1_SDA"),
+		STM32_FUNCTION(7, "I2S3_MCK"),
+		STM32_FUNCTION(10, "QUADSPI_BK1_IO3 QUADSPI_BOOTBK1_IO3"),
+		STM32_FUNCTION(11, "SAI2_SCK_A"),
+		STM32_FUNCTION(13, "FMC_A18"),
+		STM32_FUNCTION(14, "DSI_TE"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(62, "PD14"),
+		STM32_FUNCTION(0, "GPIOD14"),
+		STM32_FUNCTION(3, "TIM4_CH3"),
+		STM32_FUNCTION(7, "SAI3_MCLK_B"),
+		STM32_FUNCTION(9, "UART8_CTS UART_BOOT8_CTS"),
+		STM32_FUNCTION(13, "FMC_D0"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(63, "PD15"),
+		STM32_FUNCTION(0, "GPIOD15"),
+		STM32_FUNCTION(3, "TIM4_CH4"),
+		STM32_FUNCTION(7, "SAI3_MCLK_A"),
+		STM32_FUNCTION(9, "UART8_CTS UART_BOOT8_CTS"),
+		STM32_FUNCTION(13, "FMC_D1"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(64, "PE0"),
+		STM32_FUNCTION(0, "GPIOE0"),
+		STM32_FUNCTION(2, "LPTIM1_ETR"),
+		STM32_FUNCTION(3, "TIM4_ETR"),
+		STM32_FUNCTION(5, "LPTIM2_ETR"),
+		STM32_FUNCTION(6, "SPI3_SCK I2S3_CK"),
+		STM32_FUNCTION(7, "SAI4_MCLK_B"),
+		STM32_FUNCTION(9, "UART8_RX UART_BOOT8_RX"),
+		STM32_FUNCTION(10, "CAN1_RXFD"),
+		STM32_FUNCTION(11, "SAI2_MCLK_A"),
+		STM32_FUNCTION(13, "FMC_NBL0"),
+		STM32_FUNCTION(14, "DCMI_D2"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(65, "PE1"),
+		STM32_FUNCTION(0, "GPIOE1"),
+		STM32_FUNCTION(2, "LPTIM1_IN2"),
+		STM32_FUNCTION(6, "I2S2_MCK"),
+		STM32_FUNCTION(7, "SAI3_SD_B"),
+		STM32_FUNCTION(9, "UART8_TX UART_BOOT8_TX"),
+		STM32_FUNCTION(10, "CAN1_TXFD"),
+		STM32_FUNCTION(13, "FMC_NBL1"),
+		STM32_FUNCTION(14, "DCMI_D3"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(66, "PE2"),
+		STM32_FUNCTION(0, "GPIOE2"),
+		STM32_FUNCTION(1, "TRACECLK"),
+		STM32_FUNCTION(3, "SAI1_CK1"),
+		STM32_FUNCTION(5, "I2C4_SCL"),
+		STM32_FUNCTION(6, "SPI4_SCK"),
+		STM32_FUNCTION(7, "SAI1_MCLK_A"),
+		STM32_FUNCTION(10, "QUADSPI_BK1_IO2 QUADSPI_BOOTBK1_IO2"),
+		STM32_FUNCTION(12, "ETH_GMII_TXD3 ETH_MII_TXD3 ETH_RGMII_TXD3"),
+		STM32_FUNCTION(13, "FMC_A23"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(67, "PE3"),
+		STM32_FUNCTION(0, "GPIOE3"),
+		STM32_FUNCTION(1, "TRACED0"),
+		STM32_FUNCTION(5, "TIM15_BKIN"),
+		STM32_FUNCTION(7, "SAI1_SD_B"),
+		STM32_FUNCTION(10, "SDMMC2_CK SDMMC_BOOT2_CK"),
+		STM32_FUNCTION(13, "FMC_A19"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(68, "PE4"),
+		STM32_FUNCTION(0, "GPIOE4"),
+		STM32_FUNCTION(1, "TRACED1"),
+		STM32_FUNCTION(3, "SAI1_D2"),
+		STM32_FUNCTION(4, "DFSDM_DATA3"),
+		STM32_FUNCTION(5, "TIM15_CH1N"),
+		STM32_FUNCTION(6, "SPI4_NSS"),
+		STM32_FUNCTION(7, "SAI1_FS_A"),
+		STM32_FUNCTION(8, "SDMMC2_CKIN SDMMC_BOOT2_CKIN"),
+		STM32_FUNCTION(9, "SDMMC1_CKIN SDMMC_BOOT1_CKIN"),
+		STM32_FUNCTION(10, "SDMMC2_D4 SDMMC_BOOT2_D4"),
+		STM32_FUNCTION(12, "SDMMC1_D4 SDMMC_BOOT1_D4"),
+		STM32_FUNCTION(13, "FMC_A20"),
+		STM32_FUNCTION(14, "DCMI_D4"),
+		STM32_FUNCTION(15, "LCD_B0"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(69, "PE5"),
+		STM32_FUNCTION(0, "GPIOE5"),
+		STM32_FUNCTION(1, "TRACED3"),
+		STM32_FUNCTION(3, "SAI1_CK2"),
+		STM32_FUNCTION(4, "DFSDM_CK3"),
+		STM32_FUNCTION(5, "TIM15_CH1"),
+		STM32_FUNCTION(6, "SPI4_MISO"),
+		STM32_FUNCTION(7, "SAI1_SCK_A"),
+		STM32_FUNCTION(8, "SDMMC2_D0DIR SDMMC_BOOT2_D0DIR"),
+		STM32_FUNCTION(9, "SDMMC1_D0DIR SDMMC_BOOT1_D0DIR"),
+		STM32_FUNCTION(10, "SDMMC2_D6 SDMMC_BOOT2_D6"),
+		STM32_FUNCTION(12, "SDMMC1_D6 SDMMC_BOOT1_D6"),
+		STM32_FUNCTION(13, "FMC_A21"),
+		STM32_FUNCTION(14, "DCMI_D6"),
+		STM32_FUNCTION(15, "LCD_G0"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(70, "PE6"),
+		STM32_FUNCTION(0, "GPIOE6"),
+		STM32_FUNCTION(1, "TRACED2"),
+		STM32_FUNCTION(2, "TIM1_BKIN2"),
+		STM32_FUNCTION(3, "SAI1_D1"),
+		STM32_FUNCTION(5, "TIM15_CH2"),
+		STM32_FUNCTION(6, "SPI4_MOSI"),
+		STM32_FUNCTION(7, "SAI1_SD_A"),
+		STM32_FUNCTION(8, "SDMMC2_D0"),
+		STM32_FUNCTION(9, "SDMMC1_D2 SDMMC_BOOT1_D2"),
+		STM32_FUNCTION(11, "SAI2_MCLK_B"),
+		STM32_FUNCTION(13, "FMC_A22"),
+		STM32_FUNCTION(14, "DCMI_D7"),
+		STM32_FUNCTION(15, "LCD_G1"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(71, "PE7"),
+		STM32_FUNCTION(0, "GPIOE7"),
+		STM32_FUNCTION(2, "TIM1_ETR"),
+		STM32_FUNCTION(3, "TIM3_ETR"),
+		STM32_FUNCTION(4, "DFSDM_DATA2"),
+		STM32_FUNCTION(8, "UART7_RX"),
+		STM32_FUNCTION(11, "QUADSPI_BK2_IO0 QUADSPI_BOOTBK2_IO0"),
+		STM32_FUNCTION(13, "FMC_D4"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(72, "PE8"),
+		STM32_FUNCTION(0, "GPIOE8"),
+		STM32_FUNCTION(2, "TIM1_CH1N"),
+		STM32_FUNCTION(4, "DFSDM_CK2"),
+		STM32_FUNCTION(8, "UART7_TX"),
+		STM32_FUNCTION(11, "QUADSPI_BK2_IO1 QUADSPI_BOOTBK2_IO1"),
+		STM32_FUNCTION(13, "FMC_D5"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(73, "PE9"),
+		STM32_FUNCTION(0, "GPIOE9"),
+		STM32_FUNCTION(2, "TIM1_CH1"),
+		STM32_FUNCTION(4, "DFSDM_CKOUT"),
+		STM32_FUNCTION(8, "UART7_RTS UART_BOOT7_RTS"),
+		STM32_FUNCTION(11, "QUADSPI_BK2_IO2 QUADSPI_BOOTBK2_IO2"),
+		STM32_FUNCTION(13, "FMC_D6"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(74, "PE10"),
+		STM32_FUNCTION(0, "GPIOE10"),
+		STM32_FUNCTION(2, "TIM1_CH2N"),
+		STM32_FUNCTION(4, "DFSDM_DATA4"),
+		STM32_FUNCTION(8, "UART7_CTS UART_BOOT7_CTS"),
+		STM32_FUNCTION(11, "QUADSPI_BK2_IO3 QUADSPI_BOOTBK2_IO3"),
+		STM32_FUNCTION(13, "FMC_D7"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(75, "PE11"),
+		STM32_FUNCTION(0, "GPIOE11"),
+		STM32_FUNCTION(2, "TIM1_CH2"),
+		STM32_FUNCTION(4, "DFSDM_CK4"),
+		STM32_FUNCTION(6, "SPI4_NSS"),
+		STM32_FUNCTION(8, "USART6_CK USART_BOOT6_CK"),
+		STM32_FUNCTION(11, "SAI2_SD_B"),
+		STM32_FUNCTION(13, "FMC_D8"),
+		STM32_FUNCTION(15, "LCD_G3"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(76, "PE12"),
+		STM32_FUNCTION(0, "GPIOE12"),
+		STM32_FUNCTION(2, "TIM1_CH3N"),
+		STM32_FUNCTION(4, "DFSDM_DATA5"),
+		STM32_FUNCTION(6, "SPI4_SCK"),
+		STM32_FUNCTION(9, "SDMMC1_D0DIR SDMMC_BOOT1_D0DIR"),
+		STM32_FUNCTION(11, "SAI2_SCK_B"),
+		STM32_FUNCTION(13, "FMC_D9"),
+		STM32_FUNCTION(15, "LCD_B4"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(77, "PE13"),
+		STM32_FUNCTION(0, "GPIOE13"),
+		STM32_FUNCTION(1, "HDP2"),
+		STM32_FUNCTION(2, "TIM1_CH3"),
+		STM32_FUNCTION(4, "DFSDM_CK5"),
+		STM32_FUNCTION(6, "SPI4_MISO"),
+		STM32_FUNCTION(11, "SAI2_FS_B"),
+		STM32_FUNCTION(13, "FMC_D10"),
+		STM32_FUNCTION(15, "LCD_DE"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(78, "PE14"),
+		STM32_FUNCTION(0, "GPIOE14"),
+		STM32_FUNCTION(2, "TIM1_CH4"),
+		STM32_FUNCTION(6, "SPI4_MOSI"),
+		STM32_FUNCTION(9, "UART8_RTS UART_BOOT8_RTS"),
+		STM32_FUNCTION(11, "SAI2_MCLK_B"),
+		STM32_FUNCTION(12, "SDMMC1_D123DIR SDMMC_BOOT1_D123DIR"),
+		STM32_FUNCTION(13, "FMC_D11"),
+		STM32_FUNCTION(14, "LCD_G0"),
+		STM32_FUNCTION(15, "LCD_CLK"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(79, "PE15"),
+		STM32_FUNCTION(0, "GPIOE15"),
+		STM32_FUNCTION(1, "HDP3"),
+		STM32_FUNCTION(2, "TIM1_BKIN"),
+		STM32_FUNCTION(5, "TIM15_BKIN"),
+		STM32_FUNCTION(8, "USART2_CTS_NSS USART_BOOT2_CTS_NSS"),
+		STM32_FUNCTION(9, "UART8_CTS UART_BOOT8_CTS"),
+		STM32_FUNCTION(13, "FMC_D12"),
+		STM32_FUNCTION(15, "LCD_R7"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(80, "PF0"),
+		STM32_FUNCTION(0, "GPIOF0"),
+		STM32_FUNCTION(5, "I2C2_SDA"),
+		STM32_FUNCTION(10, "SDMMC3_D0"),
+		STM32_FUNCTION(11, "SDMMC3_CKIN"),
+		STM32_FUNCTION(13, "FMC_A0"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(81, "PF1"),
+		STM32_FUNCTION(0, "GPIOF1"),
+		STM32_FUNCTION(5, "I2C2_SCL"),
+		STM32_FUNCTION(10, "SDMMC3_CMD"),
+		STM32_FUNCTION(11, "SDMMC3_CDIR"),
+		STM32_FUNCTION(13, "FMC_A1"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(82, "PF2"),
+		STM32_FUNCTION(0, "GPIOF2"),
+		STM32_FUNCTION(5, "I2C2_SMBA"),
+		STM32_FUNCTION(10, "SDMMC2_D0DIR SDMMC_BOOT2_D0DIR"),
+		STM32_FUNCTION(11, "SDMMC3_D0DIR"),
+		STM32_FUNCTION(12, "SDMMC1_D0DIR SDMMC_BOOT1_D0DIR"),
+		STM32_FUNCTION(13, "FMC_A2"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(83, "PF3"),
+		STM32_FUNCTION(0, "GPIOF3"),
+		STM32_FUNCTION(12, "ETH_GMII_TX_ER ETH_MII_TX_ER"),
+		STM32_FUNCTION(13, "FMC_A3"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(84, "PF4"),
+		STM32_FUNCTION(0, "GPIOF4"),
+		STM32_FUNCTION(8, "USART2_RX"),
+		STM32_FUNCTION(10, "SDMMC3_D1"),
+		STM32_FUNCTION(11, "SDMMC3_D123DIR"),
+		STM32_FUNCTION(13, "FMC_A4"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(85, "PF5"),
+		STM32_FUNCTION(0, "GPIOF5"),
+		STM32_FUNCTION(8, "USART2_TX"),
+		STM32_FUNCTION(10, "SDMMC3_D2"),
+		STM32_FUNCTION(13, "FMC_A5"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(86, "PF6"),
+		STM32_FUNCTION(0, "GPIOF6"),
+		STM32_FUNCTION(2, "TIM16_CH1"),
+		STM32_FUNCTION(6, "SPI5_NSS"),
+		STM32_FUNCTION(7, "SAI1_SD_B"),
+		STM32_FUNCTION(8, "UART7_RX UART_BOOT7_RX"),
+		STM32_FUNCTION(10, "QUADSPI_BK1_IO3 QUADSPI_BOOTBK1_IO3"),
+		STM32_FUNCTION(13, "SAI4_SCK_B"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(87, "PF7"),
+		STM32_FUNCTION(0, "GPIOF7"),
+		STM32_FUNCTION(2, "TIM17_CH1"),
+		STM32_FUNCTION(6, "SPI5_SCK"),
+		STM32_FUNCTION(7, "SAI1_MCLK_B"),
+		STM32_FUNCTION(8, "UART7_TX UART_BOOT7_TX"),
+		STM32_FUNCTION(10, "QUADSPI_BK1_IO2 QUADSPI_BOOTBK1_IO2"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(88, "PF8"),
+		STM32_FUNCTION(0, "GPIOF8"),
+		STM32_FUNCTION(1, "TRACED12"),
+		STM32_FUNCTION(2, "TIM16_CH1N"),
+		STM32_FUNCTION(6, "SPI5_MISO"),
+		STM32_FUNCTION(7, "SAI1_SCK_B"),
+		STM32_FUNCTION(8, "UART7_RTS UART_BOOT7_RTS"),
+		STM32_FUNCTION(10, "TIM13_CH1"),
+		STM32_FUNCTION(11, "QUADSPI_BK1_IO0 QUADSPI_BOOTBK1_IO0"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(89, "PF9"),
+		STM32_FUNCTION(0, "GPIOF9"),
+		STM32_FUNCTION(1, "TRACED13"),
+		STM32_FUNCTION(2, "TIM17_CH1N"),
+		STM32_FUNCTION(6, "SPI5_MOSI"),
+		STM32_FUNCTION(7, "SAI1_FS_B"),
+		STM32_FUNCTION(8, "UART7_CTS UART_BOOT7_CTS"),
+		STM32_FUNCTION(10, "TIM14_CH1"),
+		STM32_FUNCTION(11, "QUADSPI_BK1_IO1 QUADSPI_BOOTBK1_IO1"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(90, "PF10"),
+		STM32_FUNCTION(0, "GPIOF10"),
+		STM32_FUNCTION(2, "TIM16_BKIN"),
+		STM32_FUNCTION(3, "SAI1_D3"),
+		STM32_FUNCTION(4, "SAI4_D4"),
+		STM32_FUNCTION(7, "SAI1_D4"),
+		STM32_FUNCTION(10, "QUADSPI_CLK QUADSPI_BOOTCLK"),
+		STM32_FUNCTION(13, "SAI4_D3"),
+		STM32_FUNCTION(14, "DCMI_D11"),
+		STM32_FUNCTION(15, "LCD_DE"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(91, "PF11"),
+		STM32_FUNCTION(0, "GPIOF11"),
+		STM32_FUNCTION(6, "SPI5_MOSI"),
+		STM32_FUNCTION(11, "SAI2_SD_B"),
+		STM32_FUNCTION(14, "DCMI_D12"),
+		STM32_FUNCTION(15, "LCD_G5"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(92, "PF12"),
+		STM32_FUNCTION(0, "GPIOF12"),
+		STM32_FUNCTION(1, "TRACED4"),
+		STM32_FUNCTION(12, "ETH_GMII_RXD4"),
+		STM32_FUNCTION(13, "FMC_A6"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(93, "PF13"),
+		STM32_FUNCTION(0, "GPIOF13"),
+		STM32_FUNCTION(1, "TRACED5"),
+		STM32_FUNCTION(4, "DFSDM_DATA6"),
+		STM32_FUNCTION(5, "I2C4_SMBA"),
+		STM32_FUNCTION(6, "I2C1_SMBA"),
+		STM32_FUNCTION(7, "DFSDM_DATA3"),
+		STM32_FUNCTION(12, "ETH_GMII_RXD5"),
+		STM32_FUNCTION(13, "FMC_A7"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(94, "PF14"),
+		STM32_FUNCTION(0, "GPIOF14"),
+		STM32_FUNCTION(1, "TRACED6"),
+		STM32_FUNCTION(4, "DFSDM_CK6"),
+		STM32_FUNCTION(5, "I2C4_SCL"),
+		STM32_FUNCTION(6, "I2C1_SCL"),
+		STM32_FUNCTION(12, "ETH_GMII_RXD6"),
+		STM32_FUNCTION(13, "FMC_A8"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(95, "PF15"),
+		STM32_FUNCTION(0, "GPIOF15"),
+		STM32_FUNCTION(1, "TRACED7"),
+		STM32_FUNCTION(5, "I2C4_SDA"),
+		STM32_FUNCTION(6, "I2C1_SDA"),
+		STM32_FUNCTION(12, "ETH_GMII_RXD7"),
+		STM32_FUNCTION(13, "FMC_A9"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(96, "PG0"),
+		STM32_FUNCTION(0, "GPIOG0"),
+		STM32_FUNCTION(1, "TRACED0"),
+		STM32_FUNCTION(4, "DFSDM_DATA0"),
+		STM32_FUNCTION(12, "ETH_GMII_TXD4"),
+		STM32_FUNCTION(13, "FMC_A10"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(97, "PG1"),
+		STM32_FUNCTION(0, "GPIOG1"),
+		STM32_FUNCTION(1, "TRACED1"),
+		STM32_FUNCTION(12, "ETH_GMII_TXD5"),
+		STM32_FUNCTION(13, "FMC_A11"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(98, "PG2"),
+		STM32_FUNCTION(0, "GPIOG2"),
+		STM32_FUNCTION(1, "TRACED2"),
+		STM32_FUNCTION(2, "MCO2"),
+		STM32_FUNCTION(4, "TIM8_BKIN"),
+		STM32_FUNCTION(12, "ETH_GMII_TXD6"),
+		STM32_FUNCTION(13, "FMC_A12"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(99, "PG3"),
+		STM32_FUNCTION(0, "GPIOG3"),
+		STM32_FUNCTION(1, "TRACED3"),
+		STM32_FUNCTION(4, "TIM8_BKIN2"),
+		STM32_FUNCTION(5, "DFSDM_CK1"),
+		STM32_FUNCTION(12, "ETH_GMII_TXD7"),
+		STM32_FUNCTION(13, "FMC_A13"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(100, "PG4"),
+		STM32_FUNCTION(0, "GPIOG4"),
+		STM32_FUNCTION(2, "TIM1_BKIN2"),
+		STM32_FUNCTION(12, "ETH_GMII_GTX_CLK ETH_RGMII_GTX_CLK"),
+		STM32_FUNCTION(13, "FMC_A14"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(101, "PG5"),
+		STM32_FUNCTION(0, "GPIOG5"),
+		STM32_FUNCTION(2, "TIM1_ETR"),
+		STM32_FUNCTION(12, "ETH_GMII_CLK125 ETH_RGMII_CLK125"),
+		STM32_FUNCTION(13, "FMC_A15"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(102, "PG6"),
+		STM32_FUNCTION(0, "GPIOG6"),
+		STM32_FUNCTION(1, "TRACED14"),
+		STM32_FUNCTION(2, "TIM17_BKIN"),
+		STM32_FUNCTION(11, "SDMMC2_CMD SDMMC_BOOT2_CMD"),
+		STM32_FUNCTION(14, "DCMI_D12"),
+		STM32_FUNCTION(15, "LCD_R7"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(103, "PG7"),
+		STM32_FUNCTION(0, "GPIOG7"),
+		STM32_FUNCTION(1, "TRACED5"),
+		STM32_FUNCTION(7, "SAI1_MCLK_A"),
+		STM32_FUNCTION(8, "USART6_CK USART_BOOT6_CK"),
+		STM32_FUNCTION(9, "UART8_RTS UART_BOOT8_RTS"),
+		STM32_FUNCTION(10, "QUADSPI_CLK"),
+		STM32_FUNCTION(12, "QUADSPI_BK2_IO3 QUADSPI_BOOTBK2_IO3"),
+		STM32_FUNCTION(13, "FMC_INT"),
+		STM32_FUNCTION(14, "DCMI_D13"),
+		STM32_FUNCTION(15, "LCD_CLK"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(104, "PG8"),
+		STM32_FUNCTION(0, "GPIOG8"),
+		STM32_FUNCTION(1, "TRACED15"),
+		STM32_FUNCTION(2, "TIM2_CH1 TIM2_ETR"),
+		STM32_FUNCTION(3, "ETH_CLK"),
+		STM32_FUNCTION(4, "TIM8_ETR"),
+		STM32_FUNCTION(6, "SPI6_NSS"),
+		STM32_FUNCTION(7, "SAI4_D2"),
+		STM32_FUNCTION(8, "USART6_RTS USART_BOOT6_RTS"),
+		STM32_FUNCTION(9, "USART3_RTS"),
+		STM32_FUNCTION(10, "SPDIF_IN2"),
+		STM32_FUNCTION(11, "SAI4_FS_A"),
+		STM32_FUNCTION(12, "ETH_PPS_OUT"),
+		STM32_FUNCTION(15, "LCD_G7"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(105, "PG9"),
+		STM32_FUNCTION(0, "GPIOG9"),
+		STM32_FUNCTION(1, "DBTRGO"),
+		STM32_FUNCTION(8, "USART6_RX"),
+		STM32_FUNCTION(9, "SPDIF_IN3"),
+		STM32_FUNCTION(10, "QUADSPI_BK2_IO2 QUADSPI_BOOTBK2_IO2"),
+		STM32_FUNCTION(11, "SAI2_FS_B"),
+		STM32_FUNCTION(13, "FMC_NE2 FMC_NCE"),
+		STM32_FUNCTION(14, "DCMI_VSYNC"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(106, "PG10"),
+		STM32_FUNCTION(0, "GPIOG10"),
+		STM32_FUNCTION(1, "TRACED10"),
+		STM32_FUNCTION(9, "UART8_CTS UART_BOOT8_CTS"),
+		STM32_FUNCTION(10, "LCD_G3"),
+		STM32_FUNCTION(11, "SAI2_SD_B"),
+		STM32_FUNCTION(12, "QUADSPI_BK2_IO2 QUADSPI_BOOTBK2_IO2"),
+		STM32_FUNCTION(13, "FMC_NE3"),
+		STM32_FUNCTION(14, "DCMI_D2"),
+		STM32_FUNCTION(15, "LCD_B2"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(107, "PG11"),
+		STM32_FUNCTION(0, "GPIOG11"),
+		STM32_FUNCTION(1, "TRACED11"),
+		STM32_FUNCTION(5, "USART1_TX"),
+		STM32_FUNCTION(7, "UART4_TX UART_BOOT4_TX"),
+		STM32_FUNCTION(9, "SPDIF_IN0"),
+		STM32_FUNCTION(12, "ETH_GMII_TX_EN ETH_MII_TX_EN ETH_RGMII_TX_CTL ETH_RMII_TX_EN"),
+		STM32_FUNCTION(14, "DCMI_D3"),
+		STM32_FUNCTION(15, "LCD_B3"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(108, "PG12"),
+		STM32_FUNCTION(0, "GPIOG12"),
+		STM32_FUNCTION(2, "LPTIM1_IN1"),
+		STM32_FUNCTION(6, "SPI6_MISO"),
+		STM32_FUNCTION(7, "SAI4_CK2"),
+		STM32_FUNCTION(8, "USART6_RTS USART_BOOT6_RTS"),
+		STM32_FUNCTION(9, "SPDIF_IN1"),
+		STM32_FUNCTION(10, "LCD_B4"),
+		STM32_FUNCTION(11, "SAI4_SCK_A"),
+		STM32_FUNCTION(12, "ETH_PHY_INTN"),
+		STM32_FUNCTION(13, "FMC_NE4"),
+		STM32_FUNCTION(15, "LCD_B1"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(109, "PG13"),
+		STM32_FUNCTION(0, "GPIOG13"),
+		STM32_FUNCTION(1, "TRACED0"),
+		STM32_FUNCTION(2, "LPTIM1_OUT"),
+		STM32_FUNCTION(3, "SAI1_CK2"),
+		STM32_FUNCTION(5, "SAI4_CK1"),
+		STM32_FUNCTION(6, "SPI6_SCK"),
+		STM32_FUNCTION(7, "SAI1_SCK_A"),
+		STM32_FUNCTION(8, "USART6_CTS_NSS USART_BOOT6_CTS_NSS"),
+		STM32_FUNCTION(11, "SAI4_MCLK_A"),
+		STM32_FUNCTION(12, "ETH_GMII_TXD0 ETH_MII_TXD0 ETH_RGMII_TXD0 ETH_RMII_TXD0"),
+		STM32_FUNCTION(13, "FMC_A24"),
+		STM32_FUNCTION(15, "LCD_R0"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(110, "PG14"),
+		STM32_FUNCTION(0, "GPIOG14"),
+		STM32_FUNCTION(1, "TRACED1"),
+		STM32_FUNCTION(2, "LPTIM1_ETR"),
+		STM32_FUNCTION(6, "SPI6_MOSI"),
+		STM32_FUNCTION(7, "SAI4_D1"),
+		STM32_FUNCTION(8, "USART6_TX"),
+		STM32_FUNCTION(10, "QUADSPI_BK2_IO3 QUADSPI_BOOTBK2_IO3"),
+		STM32_FUNCTION(11, "SAI4_SD_A"),
+		STM32_FUNCTION(12, "ETH_GMII_TXD1 ETH_MII_TXD1 ETH_RGMII_TXD1 ETH_RMII_TXD1"),
+		STM32_FUNCTION(13, "FMC_A25"),
+		STM32_FUNCTION(15, "LCD_B0"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(111, "PG15"),
+		STM32_FUNCTION(0, "GPIOG15"),
+		STM32_FUNCTION(1, "TRACED7"),
+		STM32_FUNCTION(3, "SAI1_D2"),
+		STM32_FUNCTION(5, "I2C2_SDA"),
+		STM32_FUNCTION(7, "SAI1_FS_A"),
+		STM32_FUNCTION(8, "USART6_CTS_NSS USART_BOOT6_CTS_NSS"),
+		STM32_FUNCTION(11, "SDMMC3_CK"),
+		STM32_FUNCTION(14, "DCMI_D13"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(112, "PH0"),
+		STM32_FUNCTION(0, "GPIOH0"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(113, "PH1"),
+		STM32_FUNCTION(0, "GPIOH1"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(114, "PH2"),
+		STM32_FUNCTION(0, "GPIOH2"),
+		STM32_FUNCTION(2, "LPTIM1_IN2"),
+		STM32_FUNCTION(10, "QUADSPI_BK2_IO0 QUADSPI_BOOTBK2_IO0"),
+		STM32_FUNCTION(11, "SAI2_SCK_B"),
+		STM32_FUNCTION(12, "ETH_GMII_CRS ETH_MII_CRS"),
+		STM32_FUNCTION(15, "LCD_R0"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(115, "PH3"),
+		STM32_FUNCTION(0, "GPIOH3"),
+		STM32_FUNCTION(4, "DFSDM_CK4"),
+		STM32_FUNCTION(10, "QUADSPI_BK2_IO1 QUADSPI_BOOTBK2_IO1"),
+		STM32_FUNCTION(11, "SAI2_MCLK_B"),
+		STM32_FUNCTION(12, "ETH_GMII_COL ETH_MII_COL"),
+		STM32_FUNCTION(15, "LCD_R1"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(116, "PH4"),
+		STM32_FUNCTION(0, "GPIOH4"),
+		STM32_FUNCTION(5, "I2C2_SCL"),
+		STM32_FUNCTION(10, "LCD_G5"),
+		STM32_FUNCTION(15, "LCD_G4"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(117, "PH5"),
+		STM32_FUNCTION(0, "GPIOH5"),
+		STM32_FUNCTION(5, "I2C2_SDA"),
+		STM32_FUNCTION(6, "SPI5_NSS"),
+		STM32_FUNCTION(13, "SAI4_SD_B"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(118, "PH6"),
+		STM32_FUNCTION(0, "GPIOH6"),
+		STM32_FUNCTION(3, "TIM12_CH1"),
+		STM32_FUNCTION(5, "I2C2_SMBA"),
+		STM32_FUNCTION(6, "SPI5_SCK"),
+		STM32_FUNCTION(12, "ETH_GMII_RXD2 ETH_MII_RXD2 ETH_RGMII_RXD2"),
+		STM32_FUNCTION(13, "MDIOS_MDIO"),
+		STM32_FUNCTION(14, "DCMI_D8"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(119, "PH7"),
+		STM32_FUNCTION(0, "GPIOH7"),
+		STM32_FUNCTION(5, "I2C3_SCL"),
+		STM32_FUNCTION(6, "SPI5_MISO"),
+		STM32_FUNCTION(12, "ETH_GMII_RXD3 ETH_MII_RXD3 ETH_RGMII_RXD3"),
+		STM32_FUNCTION(13, "MDIOS_MDC"),
+		STM32_FUNCTION(14, "DCMI_D9"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(120, "PH8"),
+		STM32_FUNCTION(0, "GPIOH8"),
+		STM32_FUNCTION(3, "TIM5_ETR"),
+		STM32_FUNCTION(5, "I2C3_SDA"),
+		STM32_FUNCTION(14, "DCMI_HSYNC"),
+		STM32_FUNCTION(15, "LCD_R2"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(121, "PH9"),
+		STM32_FUNCTION(0, "GPIOH9"),
+		STM32_FUNCTION(3, "TIM12_CH2"),
+		STM32_FUNCTION(5, "I2C3_SMBA"),
+		STM32_FUNCTION(14, "DCMI_D0"),
+		STM32_FUNCTION(15, "LCD_R3"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(122, "PH10"),
+		STM32_FUNCTION(0, "GPIOH10"),
+		STM32_FUNCTION(3, "TIM5_CH1"),
+		STM32_FUNCTION(5, "I2C4_SMBA"),
+		STM32_FUNCTION(6, "I2C1_SMBA"),
+		STM32_FUNCTION(14, "DCMI_D1"),
+		STM32_FUNCTION(15, "LCD_R4"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(123, "PH11"),
+		STM32_FUNCTION(0, "GPIOH11"),
+		STM32_FUNCTION(3, "TIM5_CH2"),
+		STM32_FUNCTION(5, "I2C4_SCL"),
+		STM32_FUNCTION(6, "I2C1_SCL"),
+		STM32_FUNCTION(14, "DCMI_D2"),
+		STM32_FUNCTION(15, "LCD_R5"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(124, "PH12"),
+		STM32_FUNCTION(0, "GPIOH12"),
+		STM32_FUNCTION(1, "HDP2"),
+		STM32_FUNCTION(3, "TIM5_CH3"),
+		STM32_FUNCTION(5, "I2C4_SDA"),
+		STM32_FUNCTION(6, "I2C1_SDA"),
+		STM32_FUNCTION(14, "DCMI_D3"),
+		STM32_FUNCTION(15, "LCD_R6"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(125, "PH13"),
+		STM32_FUNCTION(0, "GPIOH13"),
+		STM32_FUNCTION(4, "TIM8_CH1N"),
+		STM32_FUNCTION(9, "UART4_TX"),
+		STM32_FUNCTION(10, "CAN1_TX"),
+		STM32_FUNCTION(15, "LCD_G2"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(126, "PH14"),
+		STM32_FUNCTION(0, "GPIOH14"),
+		STM32_FUNCTION(4, "TIM8_CH2N"),
+		STM32_FUNCTION(9, "UART4_RX"),
+		STM32_FUNCTION(10, "CAN1_RX"),
+		STM32_FUNCTION(14, "DCMI_D4"),
+		STM32_FUNCTION(15, "LCD_G3"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(127, "PH15"),
+		STM32_FUNCTION(0, "GPIOH15"),
+		STM32_FUNCTION(4, "TIM8_CH3N"),
+		STM32_FUNCTION(10, "CAN1_TXFD"),
+		STM32_FUNCTION(14, "DCMI_D11"),
+		STM32_FUNCTION(15, "LCD_G4"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(128, "PI0"),
+		STM32_FUNCTION(0, "GPIOI0"),
+		STM32_FUNCTION(3, "TIM5_CH4"),
+		STM32_FUNCTION(6, "SPI2_NSS I2S2_WS"),
+		STM32_FUNCTION(10, "CAN1_RXFD"),
+		STM32_FUNCTION(14, "DCMI_D13"),
+		STM32_FUNCTION(15, "LCD_G5"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(129, "PI1"),
+		STM32_FUNCTION(0, "GPIOI1"),
+		STM32_FUNCTION(4, "TIM8_BKIN2"),
+		STM32_FUNCTION(6, "SPI2_SCK I2S2_CK"),
+		STM32_FUNCTION(14, "DCMI_D8"),
+		STM32_FUNCTION(15, "LCD_G6"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(130, "PI2"),
+		STM32_FUNCTION(0, "GPIOI2"),
+		STM32_FUNCTION(4, "TIM8_CH4"),
+		STM32_FUNCTION(6, "SPI2_MISO I2S2_SDI"),
+		STM32_FUNCTION(14, "DCMI_D9"),
+		STM32_FUNCTION(15, "LCD_G7"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(131, "PI3"),
+		STM32_FUNCTION(0, "GPIOI3"),
+		STM32_FUNCTION(4, "TIM8_ETR"),
+		STM32_FUNCTION(6, "SPI2_MOSI I2S2_SDO"),
+		STM32_FUNCTION(14, "DCMI_D10"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(132, "PI4"),
+		STM32_FUNCTION(0, "GPIOI4"),
+		STM32_FUNCTION(4, "TIM8_BKIN"),
+		STM32_FUNCTION(11, "SAI2_MCLK_A"),
+		STM32_FUNCTION(14, "DCMI_D5"),
+		STM32_FUNCTION(15, "LCD_B4"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(133, "PI5"),
+		STM32_FUNCTION(0, "GPIOI5"),
+		STM32_FUNCTION(4, "TIM8_CH1"),
+		STM32_FUNCTION(11, "SAI2_SCK_A"),
+		STM32_FUNCTION(14, "DCMI_VSYNC"),
+		STM32_FUNCTION(15, "LCD_B5"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(134, "PI6"),
+		STM32_FUNCTION(0, "GPIOI6"),
+		STM32_FUNCTION(4, "TIM8_CH2"),
+		STM32_FUNCTION(11, "SAI2_SD_A"),
+		STM32_FUNCTION(14, "DCMI_D6"),
+		STM32_FUNCTION(15, "LCD_B6"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(135, "PI7"),
+		STM32_FUNCTION(0, "GPIOI7"),
+		STM32_FUNCTION(4, "TIM8_CH3"),
+		STM32_FUNCTION(11, "SAI2_FS_A"),
+		STM32_FUNCTION(14, "DCMI_D7"),
+		STM32_FUNCTION(15, "LCD_B7"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(136, "PI8"),
+		STM32_FUNCTION(0, "GPIOI8"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(137, "PI9"),
+		STM32_FUNCTION(0, "GPIOI9"),
+		STM32_FUNCTION(1, "HDP1"),
+		STM32_FUNCTION(9, "UART4_RX"),
+		STM32_FUNCTION(10, "CAN1_RX"),
+		STM32_FUNCTION(15, "LCD_VSYNC"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(138, "PI10"),
+		STM32_FUNCTION(0, "GPIOI10"),
+		STM32_FUNCTION(1, "HDP0"),
+		STM32_FUNCTION(9, "USART3_CTS_NSS USART_BOOT3_CTS_NSS"),
+		STM32_FUNCTION(10, "CAN1_RXFD"),
+		STM32_FUNCTION(12, "ETH_GMII_RX_ER ETH_MII_RX_ER"),
+		STM32_FUNCTION(15, "LCD_HSYNC"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(139, "PI11"),
+		STM32_FUNCTION(0, "GPIOI11"),
+		STM32_FUNCTION(1, "MCO1"),
+		STM32_FUNCTION(6, "I2S_CKIN"),
+		STM32_FUNCTION(10, "LCD_G6"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(140, "PI12"),
+		STM32_FUNCTION(0, "GPIOI12"),
+		STM32_FUNCTION(1, "TRACED0"),
+		STM32_FUNCTION(3, "HDP0"),
+		STM32_FUNCTION(15, "LCD_HSYNC"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(141, "PI13"),
+		STM32_FUNCTION(0, "GPIOI13"),
+		STM32_FUNCTION(1, "TRACED1"),
+		STM32_FUNCTION(3, "HDP1"),
+		STM32_FUNCTION(15, "LCD_VSYNC"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(142, "PI14"),
+		STM32_FUNCTION(0, "GPIOI14"),
+		STM32_FUNCTION(1, "TRACECLK"),
+		STM32_FUNCTION(15, "LCD_CLK"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(143, "PI15"),
+		STM32_FUNCTION(0, "GPIOI15"),
+		STM32_FUNCTION(10, "LCD_G2"),
+		STM32_FUNCTION(15, "LCD_R0"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(144, "PJ0"),
+		STM32_FUNCTION(0, "GPIOJ0"),
+		STM32_FUNCTION(1, "TRACED8"),
+		STM32_FUNCTION(10, "LCD_R7"),
+		STM32_FUNCTION(15, "LCD_R1"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(145, "PJ1"),
+		STM32_FUNCTION(0, "GPIOJ1"),
+		STM32_FUNCTION(1, "TRACED9"),
+		STM32_FUNCTION(15, "LCD_R2"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(146, "PJ2"),
+		STM32_FUNCTION(0, "GPIOJ2"),
+		STM32_FUNCTION(1, "TRACED10"),
+		STM32_FUNCTION(14, "DSI_TE"),
+		STM32_FUNCTION(15, "LCD_R3"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(147, "PJ3"),
+		STM32_FUNCTION(0, "GPIOJ3"),
+		STM32_FUNCTION(1, "TRACED11"),
+		STM32_FUNCTION(15, "LCD_R4"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(148, "PJ4"),
+		STM32_FUNCTION(0, "GPIOJ4"),
+		STM32_FUNCTION(1, "TRACED12"),
+		STM32_FUNCTION(15, "LCD_R5"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(149, "PJ5"),
+		STM32_FUNCTION(0, "GPIOJ5"),
+		STM32_FUNCTION(1, "TRACED2"),
+		STM32_FUNCTION(3, "HDP2"),
+		STM32_FUNCTION(15, "LCD_R6"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(150, "PJ6"),
+		STM32_FUNCTION(0, "GPIOJ6"),
+		STM32_FUNCTION(1, "TRACED3"),
+		STM32_FUNCTION(3, "HDP3"),
+		STM32_FUNCTION(4, "TIM8_CH2"),
+		STM32_FUNCTION(15, "LCD_R7"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(151, "PJ7"),
+		STM32_FUNCTION(0, "GPIOJ7"),
+		STM32_FUNCTION(1, "TRACED13"),
+		STM32_FUNCTION(4, "TIM8_CH2N"),
+		STM32_FUNCTION(15, "LCD_G0"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(152, "PJ8"),
+		STM32_FUNCTION(0, "GPIOJ8"),
+		STM32_FUNCTION(1, "TRACED14"),
+		STM32_FUNCTION(2, "TIM1_CH3N"),
+		STM32_FUNCTION(4, "TIM8_CH1"),
+		STM32_FUNCTION(9, "UART8_TX"),
+		STM32_FUNCTION(15, "LCD_G1"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(153, "PJ9"),
+		STM32_FUNCTION(0, "GPIOJ9"),
+		STM32_FUNCTION(1, "TRACED15"),
+		STM32_FUNCTION(2, "TIM1_CH3"),
+		STM32_FUNCTION(4, "TIM8_CH1N"),
+		STM32_FUNCTION(9, "UART8_RX"),
+		STM32_FUNCTION(15, "LCD_G2"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(154, "PJ10"),
+		STM32_FUNCTION(0, "GPIOJ10"),
+		STM32_FUNCTION(2, "TIM1_CH2N"),
+		STM32_FUNCTION(4, "TIM8_CH2"),
+		STM32_FUNCTION(6, "SPI5_MOSI"),
+		STM32_FUNCTION(15, "LCD_G3"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(155, "PJ11"),
+		STM32_FUNCTION(0, "GPIOJ11"),
+		STM32_FUNCTION(2, "TIM1_CH2"),
+		STM32_FUNCTION(4, "TIM8_CH2N"),
+		STM32_FUNCTION(6, "SPI5_MISO"),
+		STM32_FUNCTION(15, "LCD_G4"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(156, "PJ12"),
+		STM32_FUNCTION(0, "GPIOJ12"),
+		STM32_FUNCTION(10, "LCD_G3"),
+		STM32_FUNCTION(15, "LCD_B0"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(157, "PJ13"),
+		STM32_FUNCTION(0, "GPIOJ13"),
+		STM32_FUNCTION(10, "LCD_G4"),
+		STM32_FUNCTION(15, "LCD_B1"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(158, "PJ14"),
+		STM32_FUNCTION(0, "GPIOJ14"),
+		STM32_FUNCTION(15, "LCD_B2"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(159, "PJ15"),
+		STM32_FUNCTION(0, "GPIOJ15"),
+		STM32_FUNCTION(15, "LCD_B3"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(160, "PK0"),
+		STM32_FUNCTION(0, "GPIOK0"),
+		STM32_FUNCTION(2, "TIM1_CH1N"),
+		STM32_FUNCTION(4, "TIM8_CH3"),
+		STM32_FUNCTION(6, "SPI5_SCK"),
+		STM32_FUNCTION(15, "LCD_G5"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(161, "PK1"),
+		STM32_FUNCTION(0, "GPIOK1"),
+		STM32_FUNCTION(1, "TRACED4"),
+		STM32_FUNCTION(2, "TIM1_CH1"),
+		STM32_FUNCTION(3, "HDP4"),
+		STM32_FUNCTION(4, "TIM8_CH3N"),
+		STM32_FUNCTION(6, "SPI5_NSS"),
+		STM32_FUNCTION(15, "LCD_G6"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(162, "PK2"),
+		STM32_FUNCTION(0, "GPIOK2"),
+		STM32_FUNCTION(1, "TRACED5"),
+		STM32_FUNCTION(2, "TIM1_BKIN"),
+		STM32_FUNCTION(3, "HDP5"),
+		STM32_FUNCTION(4, "TIM8_BKIN"),
+		STM32_FUNCTION(15, "LCD_G7"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(163, "PK3"),
+		STM32_FUNCTION(0, "GPIOK3"),
+		STM32_FUNCTION(15, "LCD_B4"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(164, "PK4"),
+		STM32_FUNCTION(0, "GPIOK4"),
+		STM32_FUNCTION(15, "LCD_B5"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(165, "PK5"),
+		STM32_FUNCTION(0, "GPIOK5"),
+		STM32_FUNCTION(1, "TRACED6"),
+		STM32_FUNCTION(3, "HDP6"),
+		STM32_FUNCTION(15, "LCD_B6"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(166, "PK6"),
+		STM32_FUNCTION(0, "GPIOK6"),
+		STM32_FUNCTION(1, "TRACED7"),
+		STM32_FUNCTION(3, "HDP7"),
+		STM32_FUNCTION(15, "LCD_B7"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(167, "PK7"),
+		STM32_FUNCTION(0, "GPIOK7"),
+		STM32_FUNCTION(15, "LCD_DE"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+};
+
+static const struct stm32_desc_pin stm32mp157_z_pins[] = {
+	STM32_PIN(
+		PINCTRL_PIN(400, "PZ0"),
+		STM32_FUNCTION(0, "GPIOZ0"),
+		STM32_FUNCTION(3, "I2C6_SCL"),
+		STM32_FUNCTION(4, "I2C2_SCL"),
+		STM32_FUNCTION(6, "SPI1_SCK I2S1_CK"),
+		STM32_FUNCTION(8, "USART1_CK"),
+		STM32_FUNCTION(9, "SPI6_SCK"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(401, "PZ1"),
+		STM32_FUNCTION(0, "GPIOZ1"),
+		STM32_FUNCTION(3, "I2C6_SDA"),
+		STM32_FUNCTION(4, "I2C2_SDA"),
+		STM32_FUNCTION(5, "I2C5_SDA"),
+		STM32_FUNCTION(6, "SPI1_MISO I2S1_SDI"),
+		STM32_FUNCTION(7, "I2C4_SDA"),
+		STM32_FUNCTION(8, "USART1_RX"),
+		STM32_FUNCTION(9, "SPI6_MISO"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(402, "PZ2"),
+		STM32_FUNCTION(0, "GPIOZ2"),
+		STM32_FUNCTION(3, "I2C6_SCL"),
+		STM32_FUNCTION(4, "I2C2_SCL"),
+		STM32_FUNCTION(5, "I2C5_SMBA"),
+		STM32_FUNCTION(6, "SPI1_MOSI I2S1_SDO"),
+		STM32_FUNCTION(7, "I2C4_SMBA"),
+		STM32_FUNCTION(8, "USART1_TX"),
+		STM32_FUNCTION(9, "SPI6_MOSI"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(403, "PZ3"),
+		STM32_FUNCTION(0, "GPIOZ3"),
+		STM32_FUNCTION(3, "I2C6_SDA"),
+		STM32_FUNCTION(4, "I2C2_SDA"),
+		STM32_FUNCTION(5, "I2C5_SDA"),
+		STM32_FUNCTION(6, "SPI1_NSS I2S1_WS"),
+		STM32_FUNCTION(7, "I2C4_SDA"),
+		STM32_FUNCTION(8, "USART1_CTS_NSS"),
+		STM32_FUNCTION(9, "SPI6_NSS"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(404, "PZ4"),
+		STM32_FUNCTION(0, "GPIOZ4"),
+		STM32_FUNCTION(3, "I2C6_SCL"),
+		STM32_FUNCTION(4, "I2C2_SCL"),
+		STM32_FUNCTION(5, "I2C5_SCL"),
+		STM32_FUNCTION(7, "I2C4_SCL"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(405, "PZ5"),
+		STM32_FUNCTION(0, "GPIOZ5"),
+		STM32_FUNCTION(3, "I2C6_SDA"),
+		STM32_FUNCTION(4, "I2C2_SDA"),
+		STM32_FUNCTION(5, "I2C5_SDA"),
+		STM32_FUNCTION(7, "I2C4_SDA"),
+		STM32_FUNCTION(8, "USART1_RTS"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(406, "PZ6"),
+		STM32_FUNCTION(0, "GPIOZ6"),
+		STM32_FUNCTION(3, "I2C6_SCL"),
+		STM32_FUNCTION(4, "I2C2_SCL"),
+		STM32_FUNCTION(5, "USART1_CK"),
+		STM32_FUNCTION(6, "I2S1_MCK"),
+		STM32_FUNCTION(7, "I2C4_SMBA"),
+		STM32_FUNCTION(8, "USART1_RX"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+	STM32_PIN(
+		PINCTRL_PIN(407, "PZ7"),
+		STM32_FUNCTION(0, "GPIOZ7"),
+		STM32_FUNCTION(3, "I2C6_SDA"),
+		STM32_FUNCTION(4, "I2C2_SDA"),
+		STM32_FUNCTION(8, "USART1_TX"),
+		STM32_FUNCTION(16, "EVENTOUT"),
+		STM32_FUNCTION(17, "ANALOG")
+	),
+};
+
+static struct stm32_pinctrl_match_data stm32mp157_match_data = {
+	.pins = stm32mp157_pins,
+	.npins = ARRAY_SIZE(stm32mp157_pins),
+};
+
+static struct stm32_pinctrl_match_data stm32mp157_z_match_data = {
+	.pins = stm32mp157_z_pins,
+	.npins = ARRAY_SIZE(stm32mp157_z_pins),
+};
+
+static const struct of_device_id stm32mp157_pctrl_match[] = {
+	{
+		.compatible = "st,stm32mp157-pinctrl",
+		.data = &stm32mp157_match_data,
+	},
+	{
+		.compatible = "st,stm32mp157-z-pinctrl",
+		.data = &stm32mp157_z_match_data,
+	},
+	{ }
+};
+
+static struct platform_driver stm32mp157_pinctrl_driver = {
+	.probe = stm32_pctl_probe,
+	.driver = {
+		.name = "stm32mp157-pinctrl",
+		.of_match_table = stm32mp157_pctrl_match,
+	},
+};
+
+static int __init stm32mp157_pinctrl_init(void)
+{
+	return platform_driver_register(&stm32mp157_pinctrl_driver);
+}
+arch_initcall(stm32mp157_pinctrl_init);
-- 
2.7.4

[PATCH V2 6/9] pinctrl: stm32: Add STM32MP157 MPU support

[Linus Walleij]

On Mon, Dec 18, 2017 at 4:17 PM, Ludovic Barre <ludovic.Barre@st.com> wrote:

> From: Ludovic Barre <ludovic.barre@st.com>
>
> This driver consists of 2 controllers due to a hole in mapping:
> -1 controller for GPIO bankA to K.
> -1 controller for GPIO bankZ.
>
> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
> Reviewed-by: Rob Herring <robh@kernel.org>

Patch applied.

Yours,
Linus Walleij

[PATCH V2 7/9] ARM: configs: multi_v7: add stm32 support

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds stm32 support to multi_v7_defconfig

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 arch/arm/configs/multi_v7_defconfig | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig
index 11e648a..a0163e7 100644
--- a/arch/arm/configs/multi_v7_defconfig
+++ b/arch/arm/configs/multi_v7_defconfig
@@ -77,6 +77,7 @@ CONFIG_ARCH_SPEAR13XX=y
 CONFIG_MACH_SPEAR1310=y
 CONFIG_MACH_SPEAR1340=y
 CONFIG_ARCH_STI=y
+CONFIG_ARCH_STM32=y
 CONFIG_ARCH_EXYNOS=y
 CONFIG_EXYNOS5420_MCPM=y
 CONFIG_ARCH_RENESAS=y
@@ -324,6 +325,8 @@ CONFIG_SERIAL_CONEXANT_DIGICOLOR=y
 CONFIG_SERIAL_CONEXANT_DIGICOLOR_CONSOLE=y
 CONFIG_SERIAL_ST_ASC=y
 CONFIG_SERIAL_ST_ASC_CONSOLE=y
+CONFIG_SERIAL_STM32=y
+CONFIG_SERIAL_STM32_CONSOLE=y
 CONFIG_VIRTIO_CONSOLE=y
 CONFIG_HW_RANDOM=y
 CONFIG_HW_RANDOM_ST=y
-- 
2.7.4

[PATCH V2 8/9] ARM: dts: stm32: add stm32mp157c initial support

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

Add stm32mp157c initial support with:
-Dual Cortex-A7
-Arm psci, timer, gic
-Pinctrl
-Uart

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 172 ++++++++++++++++++++++++++++++
 arch/arm/boot/dts/stm32mp157c.dtsi        | 139 ++++++++++++++++++++++++
 2 files changed, 311 insertions(+)
 create mode 100644 arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
 create mode 100644 arch/arm/boot/dts/stm32mp157c.dtsi

diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
new file mode 100644
index 0000000..440276a
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
@@ -0,0 +1,172 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
+ */
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+
+/ {
+	soc {
+		pinctrl: pin-controller {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stm32mp157-pinctrl";
+			ranges = <0 0x50002000 0xa400>;
+			pins-are-numbered;
+
+			gpioa: gpio at 50002000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x0 0x400>;
+				clocks = <&clk_pll3_p>;
+				st,bank-name = "GPIOA";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 0 16>;
+			};
+
+			gpiob: gpio at 50003000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x1000 0x400>;
+				clocks = <&clk_pll3_p>;
+				st,bank-name = "GPIOB";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 16 16>;
+			};
+
+			gpioc: gpio at 50004000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x2000 0x400>;
+				clocks = <&clk_pll3_p>;
+				st,bank-name = "GPIOC";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 32 16>;
+			};
+
+			gpiod: gpio at 50005000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x3000 0x400>;
+				clocks = <&clk_pll3_p>;
+				st,bank-name = "GPIOD";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 48 16>;
+			};
+
+			gpioe: gpio at 50006000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x4000 0x400>;
+				clocks = <&clk_pll3_p>;
+				st,bank-name = "GPIOE";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 64 16>;
+			};
+
+			gpiof: gpio at 50007000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x5000 0x400>;
+				clocks = <&clk_pll3_p>;
+				st,bank-name = "GPIOF";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 80 16>;
+			};
+
+			gpiog: gpio at 50008000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x6000 0x400>;
+				clocks = <&clk_pll3_p>;
+				st,bank-name = "GPIOG";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 96 16>;
+			};
+
+			gpioh: gpio at 50009000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x7000 0x400>;
+				clocks = <&clk_pll3_p>;
+				st,bank-name = "GPIOH";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 112 16>;
+			};
+
+			gpioi: gpio at 5000a000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x8000 0x400>;
+				clocks = <&clk_pll3_p>;
+				st,bank-name = "GPIOI";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 128 16>;
+			};
+
+			gpioj: gpio at 5000b000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x9000 0x400>;
+				clocks = <&clk_pll3_p>;
+				st,bank-name = "GPIOJ";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 144 16>;
+			};
+
+			gpiok: gpio at 5000c000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0xa000 0x400>;
+				clocks = <&clk_pll3_p>;
+				st,bank-name = "GPIOK";
+				ngpios = <8>;
+				gpio-ranges = <&pinctrl 0 160 8>;
+			};
+		};
+
+		pinctrl_z: pin-controller-z {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stm32mp157-z-pinctrl";
+			ranges = <0 0x54004000 0x400>;
+			pins-are-numbered;
+			status = "disabled";
+
+			gpioz: gpio at 54004000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0 0x400>;
+				clocks = <&clk_pll2_p>;
+				st,bank-name = "GPIOZ";
+				st,bank-ioport = <11>;
+				ngpios = <8>;
+				gpio-ranges = <&pinctrl_z 0 400 8>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/stm32mp157c.dtsi b/arch/arm/boot/dts/stm32mp157c.dtsi
new file mode 100644
index 0000000..93dbcac
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c.dtsi
@@ -0,0 +1,139 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
+ */
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu at 0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu1: cpu at 1 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci";
+		method = "smc";
+		cpu_off = <0x84000002>;
+		cpu_on = <0x84000003>;
+	};
+
+	aliases {
+		gpio0 = &gpioa;
+		gpio1 = &gpiob;
+		gpio2 = &gpioc;
+		gpio3 = &gpiod;
+		gpio4 = &gpioe;
+		gpio5 = &gpiof;
+		gpio6 = &gpiog;
+		gpio7 = &gpioh;
+		gpio8 = &gpioi;
+		gpio9 = &gpioj;
+		gpio10 = &gpiok;
+		serial3 = &uart4;
+	};
+
+	intc: interrupt-controller at a0021000 {
+		compatible = "arm,cortex-a7-gic";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0xa0021000 0x1000>,
+		      <0xa0022000 0x2000>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		interrupt-parent = <&intc>;
+	};
+
+	clocks {
+		clk_hse: clk-hse {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+		};
+
+		clk_pll_per: clk-pll-per {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <64000000>;
+		};
+
+		clk_hsi: clk-hsi {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <64000000>;
+		};
+
+		clk_lse: clk-lse {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+		};
+
+		clk_lsi: clk-lsi {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32000>;
+		};
+
+		clk_csi: clk-csi {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <4000000>;
+		};
+
+		clk_pclk1: clk-pclk1 {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <86000000>;
+		};
+
+		clk_pll3_p: clk-pll3_p {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <172000000>;
+		};
+
+		clk_pll2_p: clk-pll2_p {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <264000000>;
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		interrupt-parent = <&intc>;
+		ranges;
+
+		uart4: serial at 40010000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40010000 0x400>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_NONE>;
+			clocks = <&clk_pclk1>;
+			status = "disabled";
+		};
+	};
+};
-- 
2.7.4

[PATCH V2 9/9] ARM: dts: stm32: add initial support of stm32mp157c eval board

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

Add support of stm32mp157c evaluation board (part number: STM32MP157C-EV1)
split in 2 elements:
-Daughter board (part number: STM32MP157C-ED1)
 which includes CPU, memory and power supply
-Mother board (part number: STM32MP157C-EM1)
 which includes external peripherals (like display, camera,...)
 and extension connectors.

The daughter board can run alone, this is why the device tree files
are split in two layers, for the complete evaluation board (ev1)
and for the daughter board alone (ed1).

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
---
 arch/arm/boot/dts/Makefile                |  6 ++++--
 arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 13 +++++++++++++
 arch/arm/boot/dts/stm32mp157c-ed1.dts     | 29 +++++++++++++++++++++++++++++
 arch/arm/boot/dts/stm32mp157c-ev1.dts     | 19 +++++++++++++++++++
 4 files changed, 65 insertions(+), 2 deletions(-)
 create mode 100644 arch/arm/boot/dts/stm32mp157c-ed1.dts
 create mode 100644 arch/arm/boot/dts/stm32mp157c-ev1.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d0381e9..d72c71c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -839,7 +839,7 @@ dtb-$(CONFIG_ARCH_STI) += \
 	stih410-b2120.dtb \
 	stih410-b2260.dtb \
 	stih418-b2199.dtb
-dtb-$(CONFIG_ARCH_STM32)+= \
+dtb-$(CONFIG_ARCH_STM32) += \
 	stm32f429-disco.dtb \
 	stm32f469-disco.dtb \
 	stm32f746-disco.dtb \
@@ -847,7 +847,9 @@ dtb-$(CONFIG_ARCH_STM32)+= \
 	stm32429i-eval.dtb \
 	stm32746g-eval.dtb \
 	stm32h743i-eval.dtb \
-	stm32h743i-disco.dtb
+	stm32h743i-disco.dtb \
+	stm32mp157c-ed1.dtb \
+	stm32mp157c-ev1.dtb
 dtb-$(CONFIG_MACH_SUN4I) += \
 	sun4i-a10-a1000.dtb \
 	sun4i-a10-ba10-tvbox.dtb \
diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
index 440276a..7ac65f4 100644
--- a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
@@ -145,6 +145,19 @@
 				ngpios = <8>;
 				gpio-ranges = <&pinctrl 0 160 8>;
 			};
+
+			uart4_pins_a: uart4 at 0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <0>;
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+					bias-disable;
+				};
+			};
 		};
 
 		pinctrl_z: pin-controller-z {
diff --git a/arch/arm/boot/dts/stm32mp157c-ed1.dts b/arch/arm/boot/dts/stm32mp157c-ed1.dts
new file mode 100644
index 0000000..86acdb4
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-ed1.dts
@@ -0,0 +1,29 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved 
+ * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
+ */
+/dts-v1/;
+
+#include "stm32mp157c.dtsi"
+#include "stm32mp157-pinctrl.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157C eval daughter";
+	compatible = "st,stm32mp157c-ed1", "st,stm32mp157";
+
+	chosen {
+		bootargs = "earlyprintk console=ttySTM3,115200 root=/dev/ram";
+		stdout-path = "serial3:115200n8";
+	};
+
+	memory {
+		reg = <0xC0000000 0x40000000>;
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
new file mode 100644
index 0000000..a310703
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved 
+ * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
+ */
+/dts-v1/;
+
+#include "stm32mp157c-ed1.dts"
+
+/ {
+	model = "STMicroelectronics STM32MP157C eval daughter on eval mother";
+	compatible = "st,stm32mp157c-ev1", "st,stm32mp157c-ed1", "st,stm32mp157";
+
+	chosen {
+		bootargs = "earlyprintk console=ttySTM3,115200 root=/dev/ram";
+		stdout-path = "serial3:115200n8";
+	};
+};
+
-- 
2.7.4

[PATCH V2 9/9] ARM: dts: stm32: add initial support of stm32mp157c eval board

[Arnd Bergmann]

On Mon, Dec 18, 2017 at 4:17 PM, Ludovic Barre <ludovic.Barre@st.com> wrote:
=
> +
> +/ {
> +       model = "STMicroelectronics STM32MP157C eval daughter";
> +       compatible = "st,stm32mp157c-ed1", "st,stm32mp157";
> +
> +       chosen {
> +               bootargs = "earlyprintk console=ttySTM3,115200 root=/dev/ram";
> +               stdout-path = "serial3:115200n8";
> +       };

I'd remove the bootargs here and let the boot loader take care of
that, in particular
since all three arguments are rather old-school: earlycon is preferred over
earlyprintk, console= should not be needed if you set stdout-path, and
/dev/ram is obsoleted by initramfs.

        Arnd

[PATCH V2 9/9] ARM: dts: stm32: add initial support of stm32mp157c eval board

[Ludovic BARRE]

On 12/18/2017 09:20 PM, Arnd Bergmann wrote:
> On Mon, Dec 18, 2017 at 4:17 PM, Ludovic Barre <ludovic.Barre@st.com> wrote:
> =
>> +
>> +/ {
>> +       model = "STMicroelectronics STM32MP157C eval daughter";
>> +       compatible = "st,stm32mp157c-ed1", "st,stm32mp157";
>> +
>> +       chosen {
>> +               bootargs = "earlyprintk console=ttySTM3,115200 root=/dev/ram";
>> +               stdout-path = "serial3:115200n8";
>> +       };
> 
> I'd remove the bootargs here and let the boot loader take care of
> that, in particular
> since all three arguments are rather old-school: earlycon is preferred over
> earlyprintk, console= should not be needed if you set stdout-path, and
> /dev/ram is obsoleted by initramfs.
OK, thanks

BR
Ludo

> 
>          Arnd
> 

[PATCH V2 9/9] ARM: dts: stm32: add initial support of stm32mp157c eval board

[Alexandre Torgue]

Hi,

On 12/18/2017 09:20 PM, Arnd Bergmann wrote:
> On Mon, Dec 18, 2017 at 4:17 PM, Ludovic Barre <ludovic.Barre@st.com> wrote:
> =
>> +
>> +/ {
>> +       model = "STMicroelectronics STM32MP157C eval daughter";
>> +       compatible = "st,stm32mp157c-ed1", "st,stm32mp157";
>> +
>> +       chosen {
>> +               bootargs = "earlyprintk console=ttySTM3,115200 root=/dev/ram";
>> +               stdout-path = "serial3:115200n8";
>> +       };
> 
> I'd remove the bootargs here and let the boot loader take care of
> that, in particular
> since all three arguments are rather old-school: earlycon is preferred over
> earlyprintk, console= should not be needed if you set stdout-path, and
> /dev/ram is obsoleted by initramfs.

In this case I will modify also stm32 mcu devicetree in this way.

Thanks
Alex


> 
>          Arnd
> 

[PATCH V2 9/9] ARM: dts: stm32: add initial support of stm32mp157c eval board

[Linus Walleij]

On Mon, Dec 18, 2017 at 4:17 PM, Ludovic Barre <ludovic.Barre@st.com> wrote:

> From: Ludovic Barre <ludovic.barre@st.com>
>
> Add support of stm32mp157c evaluation board (part number: STM32MP157C-EV1)
> split in 2 elements:
> -Daughter board (part number: STM32MP157C-ED1)
>  which includes CPU, memory and power supply
> -Mother board (part number: STM32MP157C-EM1)
>  which includes external peripherals (like display, camera,...)
>  and extension connectors.
>
> The daughter board can run alone, this is why the device tree files
> are split in two layers, for the complete evaluation board (ev1)
> and for the daughter board alone (ed1).
>
> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
(...)
> diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts

Evaluation boards are important because they set a pattern that customers
will use.

Please consider to include nodes for all GPIO blocks used in this
evaluation board, and add:

gpio-line-names = "foo", "bar" ...;

See for example
arch/arm/boot/dts/bcm2835-rpi-a.dts
arch/arm/boot/dts/ste-snowball.dts

It's good to have because probably you guys have proper schematics and
know rail names of the stuff connected to those GPIO lines and so on,
so you can give the lines proper names.

It will be helpful for people using the reference design, especially with the
new character device, and also sets a pattern for people doing devices
based on the reference design and we really want to do that.

Yours,
Linus Walleij

[PATCH V2 9/9] ARM: dts: stm32: add initial support of stm32mp157c eval board

[Alexandre Torgue]

Hi Linus

On 12/20/2017 08:44 AM, Linus Walleij wrote:
> On Mon, Dec 18, 2017 at 4:17 PM, Ludovic Barre <ludovic.Barre@st.com> wrote:
> 
>> From: Ludovic Barre <ludovic.barre@st.com>
>>
>> Add support of stm32mp157c evaluation board (part number: STM32MP157C-EV1)
>> split in 2 elements:
>> -Daughter board (part number: STM32MP157C-ED1)
>>   which includes CPU, memory and power supply
>> -Mother board (part number: STM32MP157C-EM1)
>>   which includes external peripherals (like display, camera,...)
>>   and extension connectors.
>>
>> The daughter board can run alone, this is why the device tree files
>> are split in two layers, for the complete evaluation board (ev1)
>> and for the daughter board alone (ed1).
>>
>> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
>> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
> (...)
>> diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
> 
> Evaluation boards are important because they set a pattern that customers
> will use.
> 
> Please consider to include nodes for all GPIO blocks used in this
> evaluation board, and add:
> 
> gpio-line-names = "foo", "bar" ...;
> 
> See for example
> arch/arm/boot/dts/bcm2835-rpi-a.dts
> arch/arm/boot/dts/ste-snowball.dts
> 
> It's good to have because probably you guys have proper schematics and
> know rail names of the stuff connected to those GPIO lines and so on,
> so you can give the lines proper names.

It looks like useful for pins used as gpio line. Are you saying that we 
also have to describe pins used as Alternate Function ? Currently for 
stm32 MCU we add (for each pins in a group) a comment in 
stm32xxx-pinctrl.dtsi file to describe the pinmux (to help developers). 
On driver side for each stm32 pinctrl driver (ex: 
drivers/pinctrl/stm32/pinctrl-stm32f429.c) we add for each possible 
muxing a name:


	STM32_PIN(
		PINCTRL_PIN(0, "PA0"),
		STM32_FUNCTION(0, "GPIOA0"),
		STM32_FUNCTION(2, "TIM2_CH1 TIM2_ETR"),
		STM32_FUNCTION(3, "TIM5_CH1"),
		STM32_FUNCTION(4, "TIM8_ETR"),
		STM32_FUNCTION(8, "USART2_CTS"),
		STM32_FUNCTION(9, "UART4_TX"),
		STM32_FUNCTION(12, "ETH_MII_CRS"),
		STM32_FUNCTION(16, "EVENTOUT"),
		STM32_FUNCTION(17, "ANALOG")
	),

To be honest, currently there is a an issue to printout the name :) but 
I have a patch to send for that.


regards
Alex


> 
> It will be helpful for people using the reference design, especially with the
> new character device, and also sets a pattern for people doing devices
> based on the reference design and we really want to do that.
> 
> Yours,
> Linus Walleij
> 

[PATCH V2 9/9] ARM: dts: stm32: add initial support of stm32mp157c eval board

[Linus Walleij]

On Wed, Dec 20, 2017 at 10:19 AM, Alexandre Torgue
<alexandre.torgue@st.com> wrote:
> On 12/20/2017 08:44 AM, Linus Walleij wrote:

>> gpio-line-names = "foo", "bar" ...;
>>
>> See for example
>> arch/arm/boot/dts/bcm2835-rpi-a.dts
>> arch/arm/boot/dts/ste-snowball.dts
(...)
>
> It looks like useful for pins used as gpio line. Are you saying that we also
> have to describe pins used as Alternate Function ?

No. The use of the names is up to the platform maintainer (you),
leaving a blank string for non-GPIO lines is just fine.

Some platforms add the name of the actual function used by the
line on the design, if it is not GPIO, sometimes something in
brachets like "[i2c0-SDA]" that says what it is used for and explains
why you can't use it for GPIO on this setup.

But just leaving it blank is just as good.

Yours,
Linus Walleij

[PATCH V2 9/9] ARM: dts: stm32: add initial support of stm32mp157c eval board

[Alexandre Torgue]

On 12/21/2017 10:18 AM, Linus Walleij wrote:
> On Wed, Dec 20, 2017 at 10:19 AM, Alexandre Torgue
> <alexandre.torgue@st.com> wrote:
>> On 12/20/2017 08:44 AM, Linus Walleij wrote:
> 
>>> gpio-line-names = "foo", "bar" ...;
>>>
>>> See for example
>>> arch/arm/boot/dts/bcm2835-rpi-a.dts
>>> arch/arm/boot/dts/ste-snowball.dts
> (...)
>>
>> It looks like useful for pins used as gpio line. Are you saying that we also
>> have to describe pins used as Alternate Function ?
> 
> No. The use of the names is up to the platform maintainer (you),
> leaving a blank string for non-GPIO lines is just fine.
> 
> Some platforms add the name of the actual function used by the
> line on the design, if it is not GPIO, sometimes something in
> brachets like "[i2c0-SDA]" that says what it is used for and explains
> why you can't use it for GPIO on this setup.
> 
> But just leaving it blank is just as good.

Ok thanks Linus. I will take it into account. It could be useful to add 
it for MCU and future MPU boards.

Regards
Alex


> 
> Yours,
> Linus Walleij
>