From: Gregory CLEMENT <gregory.clement@bootlin.com>
To: "Marek Behún" <marek.behun@nic.cz>
Cc: Andrew Lunn <andrew@lunn.ch>,
linux-arm-kernel@lists.infradead.org,
Miquel Raynal <miquel.raynal@bootlin.com>
Subject: Re: [PATCH mvebu-dt64 1/1] arm64: dts: armada-3720-turris-mox: convert usb-phy to phy-supply
Date: Tue, 08 Oct 2019 18:58:28 +0200 [thread overview]
Message-ID: <87y2xvrx6z.fsf@FE-laptop> (raw)
In-Reply-To: <20191008184921.60e526bc@dellmb>
Hi Marek,
> Gregory,
>
> I communicated with Miquel when I first discovered this regression, see
> https://marc.info/?l=linux-usb&m=156966328310472&w=2
>
> In this mail Miquel is mentioning a patch
> (https://patchwork.kernel.org/patch/11067687/) which does the same for
> Armada 7k/8k. He says his patch should enter next release, but since on
> Mox this caused a regression, I would like it to be merged now.
I was not aware of this mail, but after reading I agree to apply it now.
>
> Anyway if you want to still wait for Miquels review to be sure, I am ok
> with that.
>
> What do you think about the "arm64: dts: armada-3720-turris-mox: add
> firmware node" which I sent last month?
I've applied a couple of minute agos.
Gregory
>
> Marek
>
> On Tue, 08 Oct 2019 18:37:03 +0200
> Gregory CLEMENT <gregory.clement@bootlin.com> wrote:
>
>> Hi Marek,
>>
>> > Update Turris Mox device tree to use the phy-supply property of the
>> > generic PHY framework instead of the legacy usb-phy property.
>> >
>> > This is needed since it caused a regression on Turris Mox since
>> > commit eb6c2eb6c7fb ("usb: host: xhci-plat: Prevent an
>> > abnormally...").
>>
>> I am not against this patch and if it the right fix for the
>> regression I will applied it on my mvebu/fixes branch to be part of
>> v5.4. However I'd like to have the feedback from Miquel on this one,
>> as for me it is not obvious that it is te correct fix.
>>
>> Gregory
>>
>> > Signed-off-by: Marek Behún <marek.behun@nic.cz>
>> > Fixes: eb6c2eb6c7fb ("usb: host: xhci-plat: Prevent an
>> > abnormally...") Cc: Miquel Raynal <miquel.raynal@bootlin.com>
>> > Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
>> > Cc: Andrew Lunn <andrew@lunn.ch>
>> > ---
>> > .../boot/dts/marvell/armada-3720-turris-mox.dts | 13
>> > +++++++------ 1 file changed, 7 insertions(+), 6 deletions(-)
>> >
>> > diff --git a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
>> > b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts index
>> > d105986c6be1..5f350cc71a2f 100644 ---
>> > a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts +++
>> > b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts @@ -60,11
>> > +60,6 @@ gpio = <&gpiosb 0 GPIO_ACTIVE_HIGH>;
>> > };
>> >
>> > - usb3_phy: usb3-phy {
>> > - compatible = "usb-nop-xceiv";
>> > - vcc-supply = <&exp_usb3_vbus>;
>> > - };
>> > -
>> > vsdc_reg: vsdc-reg {
>> > compatible = "regulator-gpio";
>> > regulator-name = "vsdc";
>> > @@ -255,10 +250,16 @@
>> > status = "okay";
>> > };
>> >
>> > +&comphy2 {
>> > + connector {
>> > + compatible = "usb-a-connector";
>> > + phy-supply = <&exp_usb3_vbus>;
>> > + };
>> > +};
>> > +
>> > &usb3 {
>> > status = "okay";
>> > phys = <&comphy2 0>;
>> > - usb-phy = <&usb3_phy>;
>> > };
>> >
>> > &mdio {
>> > --
>> > 2.21.0
>> >
>>
>
--
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
prev parent reply other threads:[~2019-10-08 16:58 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20191008145944.21659-1-marek.behun@nic.cz>
2019-10-08 16:37 ` [PATCH mvebu-dt64 1/1] arm64: dts: armada-3720-turris-mox: convert usb-phy to phy-supply Gregory CLEMENT
2019-10-08 16:49 ` Marek Behún
2019-10-08 16:54 ` Miquel Raynal
2019-10-08 16:58 ` Gregory CLEMENT [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87y2xvrx6z.fsf@FE-laptop \
--to=gregory.clement@bootlin.com \
--cc=andrew@lunn.ch \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=marek.behun@nic.cz \
--cc=miquel.raynal@bootlin.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox