* [PATCH v6 0/4] arm64: arch_timer: Add workaround for hisilicon-161601 erratum
From: Ding Tianhong @ 2017-01-06 3:41 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483594317-10732-1-git-send-email-dingtianhong@huawei.com>
Hi Marc, Will:
Please help reviewing the new version, I think it is nearly close to the final solution and it is very important to our chip or something else chip has similar erratum.
If there is any dissatisfaction, please inform me and I will fix it. :)
Thanks a lot.
Ding
On 2017/1/5 13:31, Ding Tianhong wrote:
> Erratum Hisilicon-161601 says that the ARM generic timer counter "has the
> potential to contain an erroneous value when the timer value changes".
> Accesses to TVAL (both read and write) are also affected due to the implicit counter
> read. Accesses to CVAL are not affected.
>
> The workaround is to reread the system count registers until the value of the second
> read is larger than the first one by less than 32, the system counter can be guaranteed
> not to return wrong value twice by back-to-back read and the error value is always larger
> than the correct one by 32. Writes to TVAL are replaced with an equivalent write to CVAL.
>
> v2: Introducing a new generic erratum handling mechanism for fsl,a008585 and hisilicon,161601.
> Significant rework based on feedback, including seperate the fsl erratum a008585
> to another patch, update the erratum name and remove unwanted code.
>
> v3: Introducing the erratum_workaround_set_sne generic function for fsl erratum a008585
> and make the #define __fsl_a008585_read_reg to be private to the .c file instead of
> being globally visible. After discussion with Marc and Will, a consensus decision was
> made to remove the commandline parameter for enabling fsl,erratum-a008585 erratum,
> and make some generic name more specific, export timer_unstable_counter_workaround
> for module access.
>
> Significant rework based on feedback, including fix some alignment problem, make the
> #define __hisi_161601_read_reg to be private to the .c file instead of being globally
> visible, add more accurate annotation and modify a bit of logical format to enable
> arch_timer_read_ool_enabled, remove the kernel commandline parameter
> clocksource.arm_arch_timer.hisilicon-161601.
>
> Introduce a generic aquick framework for erratum in ACPI mode.
>
> v4: rename the quirk handler parameter to make it more generic, and
> avoid break loop when handling the quirk becasue it need to
> support multi quirks handler.
>
> update some data structures for acpi mode.
>
> v5: Adapt the new kernel-parameters.txt for latest kernel version.
> Set the retries of reread system counter to 50, because it is possible
> that some interrupts may lead to more than twice read errors and break the loop,
> it will trigger the warning, so we set the number of retries far beyond the number of
> iterations the loop has been observed to take.
>
> v6: The last 2 patches in the previous version about the ACPI mode will conflict witch Fuwei's
> GTDT patches, so remove the ACPI part and only support the DT base code for this patch set.
>
> We have trigger a bug when select the CONFIG_FUNCTION_GRAPH_TRACER and enable function_graph
> to /sys/kernel/debug/tracing/current_tracer, the system will stall into an endless loop, it looks
> like that the ftrace_graph_caller will be related to xxx.read_cntvct_el0 and read the system counter
> again, so mark the xxx.read_cntvct_el0 with notrace to fix the problem.
>
> Ding Tianhong (4):
> arm64: arch_timer: Add device tree binding for hisilicon-161601
> erratum
> arm64: arch_timer: Introduce a generic erratum handing mechanism for
> fsl-a008585
> arm64: arch_timer: Work around Erratum Hisilicon-161601
> arm64: arch timer: Add timer erratum property for Hip05-d02 and
> Hip06-d03
>
> Documentation/admin-guide/kernel-parameters.txt | 9 --
> Documentation/arm64/silicon-errata.txt | 1 +
> .../devicetree/bindings/arm/arch_timer.txt | 8 ++
> arch/arm64/boot/dts/hisilicon/hip05.dtsi | 1 +
> arch/arm64/boot/dts/hisilicon/hip06.dtsi | 1 +
> arch/arm64/include/asm/arch_timer.h | 38 ++----
> drivers/clocksource/Kconfig | 9 ++
> drivers/clocksource/arm_arch_timer.c | 146 ++++++++++++++++-----
> 8 files changed, 143 insertions(+), 70 deletions(-)
>
^ permalink raw reply
* [PATCH 2/2] media: rc: add driver for IR remote receiver on MT7623 SoC
From: Andi Shyti @ 2017-01-06 3:43 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483632384-8107-3-git-send-email-sean.wang@mediatek.com>
Hi Sean,
> + ir->rc = rc_allocate_device();
Yes, you should use devm_rc_allocate_device(...)
Besides, standing to this patch which is not in yet:
https://lkml.org/lkml/2016/12/18/39
rc_allocate_device should provide the driver type during
allocation, so it should be:
ir->rc = rc_allocate_device(RC_DRIVER_IR_RAW);
and this line can be removed:
> + ir->rc->driver_type = RC_DRIVER_IR_RAW;
I don't know when Mauro will take the patch above.
Andi
^ permalink raw reply
* [PATCH v2 2/4] watchdog: bcm2835_wdt: Use watchdog core to install restart handler
From: Guenter Roeck @ 2017-01-06 3:51 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483674720-4870-1-git-send-email-linux@roeck-us.net>
Use the infrastructure provided by the watchdog core to install
the restart handler.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
---
v2: Need to call watchdog_set_restart_priority()
drivers/watchdog/bcm2835_wdt.c | 57 ++++++++++++++++++++++--------------------
1 file changed, 30 insertions(+), 27 deletions(-)
diff --git a/drivers/watchdog/bcm2835_wdt.c b/drivers/watchdog/bcm2835_wdt.c
index c32c45bd8b09..4e0adb6c88f0 100644
--- a/drivers/watchdog/bcm2835_wdt.c
+++ b/drivers/watchdog/bcm2835_wdt.c
@@ -14,7 +14,6 @@
*/
#include <linux/delay.h>
-#include <linux/reboot.h>
#include <linux/types.h>
#include <linux/module.h>
#include <linux/io.h>
@@ -49,7 +48,6 @@
struct bcm2835_wdt {
void __iomem *base;
spinlock_t lock;
- struct notifier_block restart_handler;
};
static unsigned int heartbeat;
@@ -99,11 +97,37 @@ static unsigned int bcm2835_wdt_get_timeleft(struct watchdog_device *wdog)
return WDOG_TICKS_TO_SECS(ret & PM_WDOG_TIME_SET);
}
+static void __bcm2835_restart(struct bcm2835_wdt *wdt)
+{
+ u32 val;
+
+ /* use a timeout of 10 ticks (~150us) */
+ writel_relaxed(10 | PM_PASSWORD, wdt->base + PM_WDOG);
+ val = readl_relaxed(wdt->base + PM_RSTC);
+ val &= PM_RSTC_WRCFG_CLR;
+ val |= PM_PASSWORD | PM_RSTC_WRCFG_FULL_RESET;
+ writel_relaxed(val, wdt->base + PM_RSTC);
+
+ /* No sleeping, possibly atomic. */
+ mdelay(1);
+}
+
+static int bcm2835_restart(struct watchdog_device *wdog,
+ unsigned long action, void *data)
+{
+ struct bcm2835_wdt *wdt = watchdog_get_drvdata(wdog);
+
+ __bcm2835_restart(wdt);
+
+ return 0;
+}
+
static const struct watchdog_ops bcm2835_wdt_ops = {
.owner = THIS_MODULE,
.start = bcm2835_wdt_start,
.stop = bcm2835_wdt_stop,
.get_timeleft = bcm2835_wdt_get_timeleft,
+ .restart = bcm2835_restart,
};
static const struct watchdog_info bcm2835_wdt_info = {
@@ -120,26 +144,6 @@ static struct watchdog_device bcm2835_wdt_wdd = {
.timeout = WDOG_TICKS_TO_SECS(PM_WDOG_TIME_SET),
};
-static int
-bcm2835_restart(struct notifier_block *this, unsigned long mode, void *cmd)
-{
- struct bcm2835_wdt *wdt = container_of(this, struct bcm2835_wdt,
- restart_handler);
- u32 val;
-
- /* use a timeout of 10 ticks (~150us) */
- writel_relaxed(10 | PM_PASSWORD, wdt->base + PM_WDOG);
- val = readl_relaxed(wdt->base + PM_RSTC);
- val &= PM_RSTC_WRCFG_CLR;
- val |= PM_PASSWORD | PM_RSTC_WRCFG_FULL_RESET;
- writel_relaxed(val, wdt->base + PM_RSTC);
-
- /* No sleeping, possibly atomic. */
- mdelay(1);
-
- return 0;
-}
-
/*
* We can't really power off, but if we do the normal reset scheme, and
* indicate to bootcode.bin not to reboot, then most of the chip will be
@@ -163,7 +167,7 @@ static void bcm2835_power_off(void)
writel_relaxed(val, wdt->base + PM_RSTS);
/* Continue with normal reset mechanism */
- bcm2835_restart(&wdt->restart_handler, REBOOT_HARD, NULL);
+ __bcm2835_restart(wdt);
}
static int bcm2835_wdt_probe(struct platform_device *pdev)
@@ -201,6 +205,9 @@ static int bcm2835_wdt_probe(struct platform_device *pdev)
*/
set_bit(WDOG_HW_RUNNING, &bcm2835_wdt_wdd.status);
}
+
+ watchdog_set_restart_priority(&bcm2835_wdt_wdd, 128);
+
err = watchdog_register_device(&bcm2835_wdt_wdd);
if (err) {
dev_err(dev, "Failed to register watchdog device");
@@ -208,9 +215,6 @@ static int bcm2835_wdt_probe(struct platform_device *pdev)
return err;
}
- wdt->restart_handler.notifier_call = bcm2835_restart;
- wdt->restart_handler.priority = 128;
- register_restart_handler(&wdt->restart_handler);
if (pm_power_off == NULL)
pm_power_off = bcm2835_power_off;
@@ -222,7 +226,6 @@ static int bcm2835_wdt_remove(struct platform_device *pdev)
{
struct bcm2835_wdt *wdt = platform_get_drvdata(pdev);
- unregister_restart_handler(&wdt->restart_handler);
if (pm_power_off == bcm2835_power_off)
pm_power_off = NULL;
watchdog_unregister_device(&bcm2835_wdt_wdd);
--
2.7.4
^ permalink raw reply related
* [PATCH v2 4/4] watchdog: tangox: Use watchdog core to install restart handler
From: Guenter Roeck @ 2017-01-06 3:52 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483674720-4870-1-git-send-email-linux@roeck-us.net>
Use the infrastructure provided by the watchdog core to install
the restart handler.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
---
v2: Need to call watchdog_set_restart_priority()
drivers/watchdog/tangox_wdt.c | 34 +++++++++++++---------------------
1 file changed, 13 insertions(+), 21 deletions(-)
diff --git a/drivers/watchdog/tangox_wdt.c b/drivers/watchdog/tangox_wdt.c
index 202c4b9cc921..d5fcce062920 100644
--- a/drivers/watchdog/tangox_wdt.c
+++ b/drivers/watchdog/tangox_wdt.c
@@ -15,9 +15,7 @@
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
-#include <linux/notifier.h>
#include <linux/platform_device.h>
-#include <linux/reboot.h>
#include <linux/watchdog.h>
#define DEFAULT_TIMEOUT 30
@@ -47,7 +45,6 @@ struct tangox_wdt_device {
void __iomem *base;
unsigned long clk_rate;
struct clk *clk;
- struct notifier_block restart;
};
static int tangox_wdt_set_timeout(struct watchdog_device *wdt,
@@ -96,24 +93,24 @@ static const struct watchdog_info tangox_wdt_info = {
.identity = "tangox watchdog",
};
+static int tangox_wdt_restart(struct watchdog_device *wdt,
+ unsigned long action, void *data)
+{
+ struct tangox_wdt_device *dev = watchdog_get_drvdata(wdt);
+
+ writel(1, dev->base + WD_COUNTER);
+
+ return 0;
+}
+
static const struct watchdog_ops tangox_wdt_ops = {
.start = tangox_wdt_start,
.stop = tangox_wdt_stop,
.set_timeout = tangox_wdt_set_timeout,
.get_timeleft = tangox_wdt_get_timeleft,
+ .restart = tangox_wdt_restart,
};
-static int tangox_wdt_restart(struct notifier_block *nb, unsigned long action,
- void *data)
-{
- struct tangox_wdt_device *dev =
- container_of(nb, struct tangox_wdt_device, restart);
-
- writel(1, dev->base + WD_COUNTER);
-
- return NOTIFY_DONE;
-}
-
static int tangox_wdt_probe(struct platform_device *pdev)
{
struct tangox_wdt_device *dev;
@@ -174,18 +171,14 @@ static int tangox_wdt_probe(struct platform_device *pdev)
tangox_wdt_start(&dev->wdt);
}
+ watchdog_set_restart_priority(&dev->wdt, 128);
+
err = watchdog_register_device(&dev->wdt);
if (err)
goto err;
platform_set_drvdata(pdev, dev);
- dev->restart.notifier_call = tangox_wdt_restart;
- dev->restart.priority = 128;
- err = register_restart_handler(&dev->restart);
- if (err)
- dev_warn(&pdev->dev, "failed to register restart handler\n");
-
dev_info(&pdev->dev, "SMP86xx/SMP87xx watchdog registered\n");
return 0;
@@ -202,7 +195,6 @@ static int tangox_wdt_remove(struct platform_device *pdev)
tangox_wdt_stop(&dev->wdt);
clk_disable_unprepare(dev->clk);
- unregister_restart_handler(&dev->restart);
watchdog_unregister_device(&dev->wdt);
return 0;
--
2.7.4
^ permalink raw reply related
* [PATCH v3 0/5] Add touch key driver support for TM2
From: Jaechul Lee @ 2017-01-06 3:59 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <CGME20170106035913epcas5p2b7d66596e467c6169786eea56beb8ffc@epcas5p2.samsung.com>
Hi,
This patchset adds support for the tm2 touchkey device.
The driver has been ported from Tizen Kernel, originally written
by Beomho. I ported it to the latest mainline Kernel.
This patch need to apply after this one:
https://lkml.org/lkml/2016/12/29/319
Changes in v3:
- Changed the commit ordering, the tm2-touchkey related patches
are the last 3.
- Added Chanwoo's patch which fixes the wrong voltage of ldo23
and ldo25.
- Andi (patch 3) moves the ldo31 and ldo38 in the tm2 and tm2e
files as they have different values.
Changes in v2:
- fixed reviews from Javier, Dmitry
- refactored power enable/disable functions.
- reordered signed-offs in patch 2, while patch 4 is left as it
was as Andi copy pasted the node to the new tm2.dts file
- added Jarvier's (patch 1,2,4) and Krzysztof's (patch 4) reviews
and Rob's Ack
- patch 3 diff has been generated with -B50%
Andi Shyti (1):
arm64: dts: exynos: make tm2 and tm2e independent from each other
Chanwoo Choi (1):
arm64: dts: exynos5433: TM2/E: Fix wrong information of ldo23 and
ldo25
Jaechul Lee (3):
input: Add support for the tm2 touchkey device driver
input: tm2-touchkey: Add touchkey driver support for TM2
arm64: dts: exynos: Add tm2 touchkey node
.../bindings/input/samsung,tm2-touchkey.txt | 27 +
.../boot/dts/exynos/exynos5433-tm2-common.dtsi | 1118 ++++++++++++++++++++
arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 1113 +------------------
arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts | 32 +-
drivers/input/keyboard/Kconfig | 11 +
drivers/input/keyboard/Makefile | 1 +
drivers/input/keyboard/tm2-touchkey.c | 280 +++++
7 files changed, 1469 insertions(+), 1113 deletions(-)
create mode 100644 Documentation/devicetree/bindings/input/samsung,tm2-touchkey.txt
create mode 100644 arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi
create mode 100644 drivers/input/keyboard/tm2-touchkey.c
--
2.7.4
^ permalink raw reply
* [PATCH v3 1/5] arm64: dts: exynos5433: TM2/E: Fix wrong information of ldo23 and ldo25
From: Jaechul Lee @ 2017-01-06 3:59 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483675149-32598-1-git-send-email-jcsing.lee@samsung.com>
From: Chanwoo Choi <cw00.choi@samsung.com>
This patch fixes the wrong information of ldo23 and ldo25 on both TM2 and TM2E.
Fixes: 01e5d2352152 ("arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
---
arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 7 ++++---
arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts | 10 ----------
2 files changed, 4 insertions(+), 13 deletions(-)
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
index 3b5215c..e8971f4 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
@@ -504,9 +504,9 @@
};
ldo23_reg: LDO23 {
- regulator-name = "CAM_SEN_CORE_1.2V_AP";
+ regulator-name = "CAM_SEN_CORE_1.05V_AP";
regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1200000>;
+ regulator-max-microvolt = <1050000>;
};
ldo24_reg: LDO24 {
@@ -516,9 +516,10 @@
};
ldo25_reg: LDO25 {
- regulator-name = "CAM_SEN_A2.8V_AP";
+ regulator-name = "UNUSED_LDO25";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
+ regulator-always-off;
};
ldo26_reg: LDO26 {
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts
index 1db4e7f..854c583 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts
@@ -18,16 +18,6 @@
compatible = "samsung,tm2e", "samsung,exynos5433";
};
-&ldo23_reg {
- regulator-name = "CAM_SEN_CORE_1.025V_AP";
- regulator-max-microvolt = <1050000>;
-};
-
-&ldo25_reg {
- regulator-name = "UNUSED_LDO25";
- regulator-always-off;
-};
-
&ldo31_reg {
regulator-name = "TSP_VDD_1.8V_AP";
regulator-min-microvolt = <1800000>;
--
2.7.4
^ permalink raw reply related
* [PATCH v3 2/5] arm64: dts: exynos: make tm2 and tm2e independent from each other
From: Jaechul Lee @ 2017-01-06 3:59 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483675149-32598-1-git-send-email-jcsing.lee@samsung.com>
From: Andi Shyti <andi.shyti@samsung.com>
Currently tm2e dts includes tm2 but there are some differences
between the two boards and tm2 has some properties that tm2e
doesn't have.
That's why it's important to keep the two dts files independent
and put all the commonalities in a tm2-common.dtsi file.
At the current status the only two differences between the two
dts files (besides the board name) are ldo31 and ldo38.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
---
.../boot/dts/exynos/exynos5433-tm2-common.dtsi | 1118 +++++++++++++++++++
arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 1153 +-------------------
arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts | 22 +-
3 files changed, 1163 insertions(+), 1130 deletions(-)
create mode 100644 arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi
rewrite arch/arm64/boot/dts/exynos/exynos5433-tm2.dts (98%)
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi
new file mode 100644
index 0000000..c43f9a3
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi
@@ -0,0 +1,1118 @@
+/*
+ * SAMSUNG Exynos5433 TM2 board device tree source
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ *
+ * Common device tree source file for Samsung's TM2 and TM2E boards
+ * which are based on Samsung Exynos5433 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include "exynos5433.dtsi"
+#include <dt-bindings/clock/samsung,s2mps11.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "Samsung TM2 board";
+ compatible = "samsung,tm2", "samsung,exynos5433";
+
+ aliases {
+ gsc0 = &gsc_0;
+ gsc1 = &gsc_1;
+ gsc2 = &gsc_2;
+ pinctrl0 = &pinctrl_alive;
+ pinctrl1 = &pinctrl_aud;
+ pinctrl2 = &pinctrl_cpif;
+ pinctrl3 = &pinctrl_ese;
+ pinctrl4 = &pinctrl_finger;
+ pinctrl5 = &pinctrl_fsys;
+ pinctrl6 = &pinctrl_imem;
+ pinctrl7 = &pinctrl_nfc;
+ pinctrl8 = &pinctrl_peric;
+ pinctrl9 = &pinctrl_touch;
+ serial0 = &serial_0;
+ serial1 = &serial_1;
+ serial2 = &serial_2;
+ serial3 = &serial_3;
+ spi0 = &spi_0;
+ spi1 = &spi_1;
+ spi2 = &spi_2;
+ spi3 = &spi_3;
+ spi4 = &spi_4;
+ mshc0 = &mshc_0;
+ mshc2 = &mshc_2;
+ };
+
+ chosen {
+ stdout-path = &serial_1;
+ };
+
+ memory at 20000000 {
+ device_type = "memory";
+ reg = <0x0 0x20000000 0x0 0xc0000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ power-key {
+ gpios = <&gpa2 7 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ label = "power key";
+ debounce-interval = <10>;
+ };
+
+ volume-up-key {
+ gpios = <&gpa2 0 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ label = "volume-up key";
+ debounce-interval = <10>;
+ };
+
+ volume-down-key {
+ gpios = <&gpa2 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ label = "volume-down key";
+ debounce-interval = <10>;
+ };
+
+ homepage-key {
+ gpios = <&gpa0 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_MENU>;
+ label = "homepage key";
+ debounce-interval = <10>;
+ };
+ };
+
+ i2c_max98504: i2c-gpio-0 {
+ compatible = "i2c-gpio";
+ gpios = <&gpd0 1 GPIO_ACTIVE_HIGH /* SPK_AMP_SDA */
+ &gpd0 0 GPIO_ACTIVE_HIGH /* SPK_AMP_SCL */ >;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ max98504: max98504 at 31 {
+ compatible = "maxim,max98504";
+ reg = <0x31>;
+ maxim,rx-path = <1>;
+ maxim,tx-path = <1>;
+ maxim,tx-channel-mask = <3>;
+ maxim,tx-channel-source = <2>;
+ };
+ };
+
+ sound {
+ compatible = "samsung,tm2-audio";
+ audio-codec = <&wm5110>;
+ i2s-controller = <&i2s0>;
+ audio-amplifier = <&max98504>;
+ mic-bias-gpios = <&gpr3 2 GPIO_ACTIVE_HIGH>;
+ model = "wm5110";
+ samsung,audio-routing =
+ /* Headphone */
+ "HP", "HPOUT1L",
+ "HP", "HPOUT1R",
+
+ /* Speaker */
+ "SPK", "SPKOUT",
+ "SPKOUT", "HPOUT2L",
+ "SPKOUT", "HPOUT2R",
+
+ /* Receiver */
+ "RCV", "HPOUT3L",
+ "RCV", "HPOUT3R";
+ status = "okay";
+ };
+};
+
+&adc {
+ vdd-supply = <&ldo3_reg>;
+ status = "okay";
+
+ thermistor-ap {
+ compatible = "murata,ncp03wf104";
+ pullup-uv = <1800000>;
+ pullup-ohm = <100000>;
+ pulldown-ohm = <0>;
+ io-channels = <&adc 0>;
+ };
+
+ thermistor-battery {
+ compatible = "murata,ncp03wf104";
+ pullup-uv = <1800000>;
+ pullup-ohm = <100000>;
+ pulldown-ohm = <0>;
+ io-channels = <&adc 1>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ thermistor-charger {
+ compatible = "murata,ncp03wf104";
+ pullup-uv = <1800000>;
+ pullup-ohm = <100000>;
+ pulldown-ohm = <0>;
+ io-channels = <&adc 2>;
+ };
+};
+
+&bus_g2d_400 {
+ devfreq-events = <&ppmu_event0_d0_general>, <&ppmu_event0_d1_general>;
+ vdd-supply = <&buck4_reg>;
+ exynos,saturation-ratio = <10>;
+ status = "okay";
+};
+
+&bus_g2d_266 {
+ devfreq = <&bus_g2d_400>;
+ status = "okay";
+};
+
+&bus_gscl {
+ devfreq = <&bus_g2d_400>;
+ status = "okay";
+};
+
+&bus_hevc {
+ devfreq = <&bus_g2d_400>;
+ status = "okay";
+};
+
+&bus_jpeg {
+ devfreq = <&bus_g2d_400>;
+ status = "okay";
+};
+
+&bus_mfc {
+ devfreq = <&bus_g2d_400>;
+ status = "okay";
+};
+
+&bus_mscl {
+ devfreq = <&bus_g2d_400>;
+ status = "okay";
+};
+
+&bus_noc0 {
+ devfreq = <&bus_g2d_400>;
+ status = "okay";
+};
+
+&bus_noc1 {
+ devfreq = <&bus_g2d_400>;
+ status = "okay";
+};
+
+&bus_noc2 {
+ devfreq = <&bus_g2d_400>;
+ status = "okay";
+};
+
+&cmu_aud {
+ assigned-clocks = <&cmu_aud CLK_MOUT_AUD_PLL_USER>;
+ assigned-clock-parents = <&cmu_top CLK_FOUT_AUD_PLL>;
+};
+
+&cmu_fsys {
+ assigned-clocks = <&cmu_top CLK_MOUT_SCLK_USBDRD30>,
+ <&cmu_top CLK_MOUT_SCLK_USBHOST30>,
+ <&cmu_fsys CLK_MOUT_SCLK_USBDRD30_USER>,
+ <&cmu_fsys CLK_MOUT_SCLK_USBHOST30_USER>,
+ <&cmu_fsys CLK_MOUT_PHYCLK_USBDRD30_UDRD30_PIPE_PCLK_USER>,
+ <&cmu_fsys CLK_MOUT_PHYCLK_USBHOST30_UHOST30_PIPE_PCLK_USER>,
+ <&cmu_fsys CLK_MOUT_PHYCLK_USBDRD30_UDRD30_PHYCLOCK_USER>,
+ <&cmu_fsys CLK_MOUT_PHYCLK_USBHOST30_UHOST30_PHYCLOCK_USER>,
+ <&cmu_top CLK_DIV_SCLK_USBDRD30>,
+ <&cmu_top CLK_DIV_SCLK_USBHOST30>;
+ assigned-clock-parents = <&cmu_top CLK_MOUT_BUS_PLL_USER>,
+ <&cmu_top CLK_MOUT_BUS_PLL_USER>,
+ <&cmu_top CLK_SCLK_USBDRD30_FSYS>,
+ <&cmu_top CLK_SCLK_USBHOST30_FSYS>,
+ <&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PIPE_PCLK_PHY>,
+ <&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PIPE_PCLK_PHY>,
+ <&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PHYCLOCK_PHY>,
+ <&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PHYCLOCK_PHY>;
+ assigned-clock-rates = <0>, <0>, <0>, <0>, <0>, <0>, <0>, <0>,
+ <66700000>, <66700000>;
+};
+
+&cmu_gscl {
+ assigned-clocks = <&cmu_gscl CLK_MOUT_ACLK_GSCL_111_USER>,
+ <&cmu_gscl CLK_MOUT_ACLK_GSCL_333_USER>;
+ assigned-clock-parents = <&cmu_top CLK_ACLK_GSCL_111>,
+ <&cmu_top CLK_ACLK_GSCL_333>;
+};
+
+&cmu_mfc {
+ assigned-clocks = <&cmu_mfc CLK_MOUT_ACLK_MFC_400_USER>;
+ assigned-clock-parents = <&cmu_top CLK_ACLK_MFC_400>;
+};
+
+&cmu_mscl {
+ assigned-clocks = <&cmu_mscl CLK_MOUT_ACLK_MSCL_400_USER>,
+ <&cmu_mscl CLK_MOUT_SCLK_JPEG_USER>,
+ <&cmu_mscl CLK_MOUT_SCLK_JPEG>,
+ <&cmu_top CLK_MOUT_SCLK_JPEG_A>;
+ assigned-clock-parents = <&cmu_top CLK_ACLK_MSCL_400>,
+ <&cmu_top CLK_SCLK_JPEG_MSCL>,
+ <&cmu_mscl CLK_MOUT_SCLK_JPEG_USER>,
+ <&cmu_top CLK_MOUT_BUS_PLL_USER>;
+};
+
+&cpu0 {
+ cpu-supply = <&buck3_reg>;
+};
+
+&cpu4 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&decon {
+ status = "okay";
+
+ i80-if-timings {
+ };
+};
+
+&dsi {
+ status = "okay";
+ vddcore-supply = <&ldo6_reg>;
+ vddio-supply = <&ldo7_reg>;
+ samsung,pll-clock-frequency = <24000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&te_irq>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 1 {
+ reg = <1>;
+
+ dsi_out: endpoint {
+ samsung,burst-clock-frequency = <512000000>;
+ samsung,esc-clock-frequency = <16000000>;
+ };
+ };
+ };
+};
+
+&hsi2c_0 {
+ status = "okay";
+ clock-frequency = <2500000>;
+
+ s2mps13-pmic at 66 {
+ compatible = "samsung,s2mps13-pmic";
+ interrupt-parent = <&gpa0>;
+ interrupts = <7 IRQ_TYPE_NONE>;
+ reg = <0x66>;
+ samsung,s2mps11-wrstbi-ground;
+
+ s2mps13_osc: clocks {
+ compatible = "samsung,s2mps13-clk";
+ #clock-cells = <1>;
+ clock-output-names = "s2mps13_ap", "s2mps13_cp",
+ "s2mps13_bt";
+ };
+
+ regulators: regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VDD_ALIVE_0.9V_AP";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "VDDQ_MMC2_2.8V_AP";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "VDD1_E_1.8V_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "VDD10_MIF_PLL_1.0V_AP";
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "VDD10_DPLL_1.0V_AP";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "VDD10_MIPI2L_1.0V_AP";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "VDD18_MIPI2L_1.8V_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "VDD18_LLI_1.8V_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "VDD18_ABB_ETC_1.8V_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "VDD33_USB30_3.0V_AP";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "VDD_INT_M_1.0V_AP";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "VDD_KFC_M_1.1V_AP";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ };
+
+ ldo13_reg: LDO13 {
+ regulator-name = "VDD_G3D_M_0.95V_AP";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <950000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo14_reg: LDO14 {
+ regulator-name = "VDDQ_M1_LDO_1.2V_AP";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "VDDQ_M2_LDO_1.2V_AP";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "VDDQ_EFUSE";
+ regulator-min-microvolt = <1400000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-always-on;
+ };
+
+ ldo17_reg: LDO17 {
+ regulator-name = "V_TFLASH_2.8V_AP";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo18_reg: LDO18 {
+ regulator-name = "V_CODEC_1.8V_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo19_reg: LDO19 {
+ regulator-name = "VDDA_1.8V_COMP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo20_reg: LDO20 {
+ regulator-name = "VCC_2.8V_AP";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ ldo21_reg: LDO21 {
+ regulator-name = "VT_CAM_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo22_reg: LDO22 {
+ regulator-name = "CAM_IO_1.8V_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo23_reg: LDO23 {
+ regulator-name = "CAM_SEN_CORE_1.05V_AP";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ ldo24_reg: LDO24 {
+ regulator-name = "VT_CAM_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ ldo25_reg: LDO25 {
+ regulator-name = "UNUSED_LDO25";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-off;
+ };
+
+ ldo26_reg: LDO26 {
+ regulator-name = "CAM_AF_2.8V_AP";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo27_reg: LDO27 {
+ regulator-name = "VCC_3.0V_LCD_AP";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ ldo28_reg: LDO28 {
+ regulator-name = "VCC_1.8V_LCD_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo29_reg: LDO29 {
+ regulator-name = "VT_CAM_2.8V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ ldo30_reg: LDO30 {
+ regulator-name = "TSP_AVDD_3.3V_AP";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ /*
+ * LDO31 differs from target to target,
+ * its definition is in the .dts
+ */
+
+ ldo32_reg: LDO32 {
+ regulator-name = "VTOUCH_1.8V_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo33_reg: LDO33 {
+ regulator-name = "VTOUCH_LED_3.3V";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-ramp-delay = <12500>;
+ };
+
+ ldo34_reg: LDO34 {
+ regulator-name = "VCC_1.8V_MHL_AP";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <2100000>;
+ };
+
+ ldo35_reg: LDO35 {
+ regulator-name = "OIS_VM_2.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo36_reg: LDO36 {
+ regulator-name = "VSIL_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ ldo37_reg: LDO37 {
+ regulator-name = "VF_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ /*
+ * LDO38 differs from target to target,
+ * its definition is in the .dts
+ */
+
+ ldo39_reg: LDO39 {
+ regulator-name = "V_HRM_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo40_reg: LDO40 {
+ regulator-name = "V_HRM_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "VDD_MIF_0.9V_AP";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "VDD_EGL_1.0V_AP";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "VDD_KFC_1.0V_AP";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "VDD_INT_0.95V_AP";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "VDD_DISP_CAM0_0.9V_AP";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck6_reg: BUCK6 {
+ regulator-name = "VDD_G3D_0.9V_AP";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck7_reg: BUCK7 {
+ regulator-name = "VDD_MEM1_1.2V_AP";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ buck8_reg: BUCK8 {
+ regulator-name = "VDD_LLDO_1.35V_AP";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ buck9_reg: BUCK9 {
+ regulator-name = "VDD_MLDO_2.0V_AP";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ buck10_reg: BUCK10 {
+ regulator-name = "vdd_mem2";
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&hsi2c_8 {
+ status = "okay";
+
+ max77843 at 66 {
+ compatible = "maxim,max77843";
+ interrupt-parent = <&gpa1>;
+ interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+ reg = <0x66>;
+
+ muic: max77843-muic {
+ compatible = "maxim,max77843-muic";
+ };
+
+ regulators {
+ compatible = "maxim,max77843-regulator";
+ safeout1_reg: SAFEOUT1 {
+ regulator-name = "SAFEOUT1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <4950000>;
+ };
+
+ safeout2_reg: SAFEOUT2 {
+ regulator-name = "SAFEOUT2";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <4950000>;
+ };
+
+ charger_reg: CHARGER {
+ regulator-name = "CHARGER";
+ regulator-min-microamp = <100000>;
+ regulator-max-microamp = <3150000>;
+ };
+ };
+
+ haptic: max77843-haptic {
+ compatible = "maxim,max77843-haptic";
+ haptic-supply = <&ldo38_reg>;
+ pwms = <&pwm 0 33670 0>;
+ pwm-names = "haptic";
+ };
+ };
+};
+
+&i2s0 {
+ status = "okay";
+};
+
+&mshc_0 {
+ status = "okay";
+ num-slots = <1>;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ cap-mmc-highspeed;
+ non-removable;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <0 4>;
+ samsung,dw-mshc-ddr-timing = <0 2>;
+ samsung,dw-mshc-hs400-timing = <0 3>;
+ samsung,read-strobe-delay = <90>;
+ fifo-depth = <0x80>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_qrdy &sd0_bus1 &sd0_bus4
+ &sd0_bus8 &sd0_rdqs>;
+ bus-width = <8>;
+ assigned-clocks = <&cmu_top CLK_SCLK_MMC0_FSYS>;
+ assigned-clock-rates = <800000000>;
+};
+
+&mshc_2 {
+ status = "okay";
+ num-slots = <1>;
+ cap-sd-highspeed;
+ disable-wp;
+ cd-gpios = <&gpa2 4 GPIO_ACTIVE_HIGH>;
+ cd-inverted;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <0 4>;
+ samsung,dw-mshc-ddr-timing = <0 2>;
+ fifo-depth = <0x80>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus1 &sd2_bus4>;
+ bus-width = <4>;
+};
+
+&ppmu_d0_general {
+ status = "okay";
+ events {
+ ppmu_event0_d0_general: ppmu-event0-d0-general {
+ event-name = "ppmu-event0-d0-general";
+ };
+ };
+};
+
+&ppmu_d1_general {
+ status = "okay";
+ events {
+ ppmu_event0_d1_general: ppmu-event0-d1-general {
+ event-name = "ppmu-event0-d1-general";
+ };
+ };
+};
+
+&pinctrl_alive {
+ pinctrl-names = "default";
+ pinctrl-0 = <&initial_alive>;
+
+ initial_alive: initial-state {
+ PIN(INPUT, gpa0-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpa0-1, NONE, FAST_SR1);
+ PIN(INPUT, gpa0-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpa0-3, NONE, FAST_SR1);
+ PIN(INPUT, gpa0-4, NONE, FAST_SR1);
+ PIN(INPUT, gpa0-5, DOWN, FAST_SR1);
+ PIN(INPUT, gpa0-6, NONE, FAST_SR1);
+ PIN(INPUT, gpa0-7, NONE, FAST_SR1);
+
+ PIN(INPUT, gpa1-0, UP, FAST_SR1);
+ PIN(INPUT, gpa1-1, NONE, FAST_SR1);
+ PIN(INPUT, gpa1-2, NONE, FAST_SR1);
+ PIN(INPUT, gpa1-3, DOWN, FAST_SR1);
+ PIN(INPUT, gpa1-4, DOWN, FAST_SR1);
+ PIN(INPUT, gpa1-5, NONE, FAST_SR1);
+ PIN(INPUT, gpa1-6, NONE, FAST_SR1);
+ PIN(INPUT, gpa1-7, NONE, FAST_SR1);
+
+ PIN(INPUT, gpa2-0, NONE, FAST_SR1);
+ PIN(INPUT, gpa2-1, NONE, FAST_SR1);
+ PIN(INPUT, gpa2-2, NONE, FAST_SR1);
+ PIN(INPUT, gpa2-3, DOWN, FAST_SR1);
+ PIN(INPUT, gpa2-4, NONE, FAST_SR1);
+ PIN(INPUT, gpa2-5, DOWN, FAST_SR1);
+ PIN(INPUT, gpa2-6, DOWN, FAST_SR1);
+ PIN(INPUT, gpa2-7, NONE, FAST_SR1);
+
+ PIN(INPUT, gpa3-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpa3-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpa3-2, NONE, FAST_SR1);
+ PIN(INPUT, gpa3-3, DOWN, FAST_SR1);
+ PIN(INPUT, gpa3-4, NONE, FAST_SR1);
+ PIN(INPUT, gpa3-5, DOWN, FAST_SR1);
+ PIN(INPUT, gpa3-6, DOWN, FAST_SR1);
+ PIN(INPUT, gpa3-7, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpf1-0, NONE, FAST_SR1);
+ PIN(INPUT, gpf1-1, NONE, FAST_SR1);
+ PIN(INPUT, gpf1-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpf1-4, UP, FAST_SR1);
+ PIN(OUTPUT, gpf1-5, NONE, FAST_SR1);
+ PIN(INPUT, gpf1-6, DOWN, FAST_SR1);
+ PIN(INPUT, gpf1-7, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpf2-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpf2-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpf2-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpf2-3, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpf3-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpf3-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpf3-2, NONE, FAST_SR1);
+ PIN(INPUT, gpf3-3, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpf4-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpf4-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpf4-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpf4-3, DOWN, FAST_SR1);
+ PIN(INPUT, gpf4-4, DOWN, FAST_SR1);
+ PIN(INPUT, gpf4-5, DOWN, FAST_SR1);
+ PIN(INPUT, gpf4-6, DOWN, FAST_SR1);
+ PIN(INPUT, gpf4-7, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpf5-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpf5-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpf5-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpf5-3, DOWN, FAST_SR1);
+ PIN(OUTPUT, gpf5-4, NONE, FAST_SR1);
+ PIN(INPUT, gpf5-5, DOWN, FAST_SR1);
+ PIN(INPUT, gpf5-6, DOWN, FAST_SR1);
+ PIN(INPUT, gpf5-7, DOWN, FAST_SR1);
+ };
+
+ te_irq: te_irq {
+ samsung,pins = "gpf1-3";
+ samsung,pin-function = <0xf>;
+ };
+};
+
+&pinctrl_cpif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&initial_cpif>;
+
+ initial_cpif: initial-state {
+ PIN(INPUT, gpv6-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpv6-1, DOWN, FAST_SR1);
+ };
+};
+
+&pinctrl_ese {
+ pinctrl-names = "default";
+ pinctrl-0 = <&initial_ese>;
+
+ initial_ese: initial-state {
+ PIN(INPUT, gpj2-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpj2-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpj2-2, DOWN, FAST_SR1);
+ };
+};
+
+&pinctrl_fsys {
+ pinctrl-names = "default";
+ pinctrl-0 = <&initial_fsys>;
+
+ initial_fsys: initial-state {
+ PIN(INPUT, gpr3-0, NONE, FAST_SR1);
+ PIN(INPUT, gpr3-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpr3-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpr3-3, DOWN, FAST_SR1);
+ PIN(INPUT, gpr3-7, NONE, FAST_SR1);
+ };
+};
+
+&pinctrl_imem {
+ pinctrl-names = "default";
+ pinctrl-0 = <&initial_imem>;
+
+ initial_imem: initial-state {
+ PIN(INPUT, gpf0-0, UP, FAST_SR1);
+ PIN(INPUT, gpf0-1, UP, FAST_SR1);
+ PIN(INPUT, gpf0-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpf0-3, UP, FAST_SR1);
+ PIN(INPUT, gpf0-4, DOWN, FAST_SR1);
+ PIN(INPUT, gpf0-5, NONE, FAST_SR1);
+ PIN(INPUT, gpf0-6, DOWN, FAST_SR1);
+ PIN(INPUT, gpf0-7, UP, FAST_SR1);
+ };
+};
+
+&pinctrl_nfc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&initial_nfc>;
+
+ initial_nfc: initial-state {
+ PIN(INPUT, gpj0-2, DOWN, FAST_SR1);
+ };
+};
+
+&pinctrl_peric {
+ pinctrl-names = "default";
+ pinctrl-0 = <&initial_peric>;
+
+ initial_peric: initial-state {
+ PIN(INPUT, gpv7-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpv7-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpv7-2, NONE, FAST_SR1);
+ PIN(INPUT, gpv7-3, DOWN, FAST_SR1);
+ PIN(INPUT, gpv7-4, DOWN, FAST_SR1);
+ PIN(INPUT, gpv7-5, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpb0-4, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpc0-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpc0-5, DOWN, FAST_SR1);
+ PIN(INPUT, gpc0-7, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpc1-1, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpc3-4, NONE, FAST_SR1);
+ PIN(INPUT, gpc3-5, NONE, FAST_SR1);
+ PIN(INPUT, gpc3-6, NONE, FAST_SR1);
+ PIN(INPUT, gpc3-7, NONE, FAST_SR1);
+
+ PIN(OUTPUT, gpg0-0, NONE, FAST_SR1);
+ PIN(2, gpg0-1, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpd2-5, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpd4-0, NONE, FAST_SR1);
+ PIN(INPUT, gpd4-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpd4-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpd4-3, DOWN, FAST_SR1);
+ PIN(INPUT, gpd4-4, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpd6-3, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpd8-1, UP, FAST_SR1);
+
+ PIN(INPUT, gpg1-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpg1-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpg1-2, DOWN, FAST_SR1);
+ PIN(INPUT, gpg1-3, DOWN, FAST_SR1);
+ PIN(INPUT, gpg1-4, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpg2-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpg2-1, DOWN, FAST_SR1);
+
+ PIN(INPUT, gpg3-0, DOWN, FAST_SR1);
+ PIN(INPUT, gpg3-1, DOWN, FAST_SR1);
+ PIN(INPUT, gpg3-5, DOWN, FAST_SR1);
+ PIN(INPUT, gpg3-7, DOWN, FAST_SR1);
+ };
+};
+
+&pinctrl_touch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&initial_touch>;
+
+ initial_touch: initial-state {
+ PIN(INPUT, gpj1-2, DOWN, FAST_SR1);
+ };
+};
+
+&pwm {
+ pinctrl-0 = <&pwm0_out>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&mic {
+ status = "okay";
+
+ i80-if-timings {
+ };
+};
+
+&pmu_system_controller {
+ assigned-clocks = <&pmu_system_controller 0>;
+ assigned-clock-parents = <&xxti>;
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&spi_1 {
+ cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ wm5110: wm5110-codec at 0 {
+ compatible = "wlf,wm5110";
+ reg = <0x0>;
+ spi-max-frequency = <20000000>;
+ interrupt-parent = <&gpa0>;
+ interrupts = <4 IRQ_TYPE_NONE>;
+ clocks = <&pmu_system_controller 0>,
+ <&s2mps13_osc S2MPS11_CLK_BT>;
+ clock-names = "mclk1", "mclk2";
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ wlf,micd-detect-debounce = <300>;
+ wlf,micd-bias-start-time = <0x1>;
+ wlf,micd-rate = <0x7>;
+ wlf,micd-dbtime = <0x1>;
+ wlf,micd-force-micbias;
+ wlf,micd-configs = <0x0 1 0>;
+ wlf,hpdet-channel = <1>;
+ wlf,gpsw = <0x1>;
+ wlf,inmode = <2 0 2 0>;
+
+ wlf,reset = <&gpc0 7 GPIO_ACTIVE_HIGH>;
+ wlf,ldoena = <&gpf0 0 GPIO_ACTIVE_HIGH>;
+
+ /* core supplies */
+ AVDD-supply = <&ldo18_reg>;
+ DBVDD1-supply = <&ldo18_reg>;
+ CPVDD-supply = <&ldo18_reg>;
+ DBVDD2-supply = <&ldo18_reg>;
+ DBVDD3-supply = <&ldo18_reg>;
+
+ controller-data {
+ samsung,spi-feedback-delay = <0>;
+ };
+ };
+};
+
+&timer {
+ clock-frequency = <24000000>;
+};
+
+&tmu_atlas0 {
+ vtmu-supply = <&ldo3_reg>;
+ status = "okay";
+};
+
+&tmu_apollo {
+ vtmu-supply = <&ldo3_reg>;
+ status = "okay";
+};
+
+&tmu_g3d {
+ vtmu-supply = <&ldo3_reg>;
+ status = "okay";
+};
+
+&usbdrd30 {
+ vdd33-supply = <&ldo10_reg>;
+ vdd10-supply = <&ldo6_reg>;
+ status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+ dr_mode = "otg";
+};
+
+&usbdrd30_phy {
+ vbus-supply = <&safeout1_reg>;
+ status = "okay";
+};
+
+&xxti {
+ clock-frequency = <24000000>;
+};
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
dissimilarity index 98%
index e8971f4..d30b45a 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
@@ -1,1120 +1,33 @@
-/*
- * SAMSUNG Exynos5433 TM2 board device tree source
- *
- * Copyright (c) 2016 Samsung Electronics Co., Ltd.
- *
- * Device tree source file for Samsung's TM2 board which is based on
- * Samsung Exynos5433 SoC.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-/dts-v1/;
-#include "exynos5433.dtsi"
-#include <dt-bindings/clock/samsung,s2mps11.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-
-/ {
- model = "Samsung TM2 board";
- compatible = "samsung,tm2", "samsung,exynos5433";
-
- aliases {
- gsc0 = &gsc_0;
- gsc1 = &gsc_1;
- gsc2 = &gsc_2;
- pinctrl0 = &pinctrl_alive;
- pinctrl1 = &pinctrl_aud;
- pinctrl2 = &pinctrl_cpif;
- pinctrl3 = &pinctrl_ese;
- pinctrl4 = &pinctrl_finger;
- pinctrl5 = &pinctrl_fsys;
- pinctrl6 = &pinctrl_imem;
- pinctrl7 = &pinctrl_nfc;
- pinctrl8 = &pinctrl_peric;
- pinctrl9 = &pinctrl_touch;
- serial0 = &serial_0;
- serial1 = &serial_1;
- serial2 = &serial_2;
- serial3 = &serial_3;
- spi0 = &spi_0;
- spi1 = &spi_1;
- spi2 = &spi_2;
- spi3 = &spi_3;
- spi4 = &spi_4;
- mshc0 = &mshc_0;
- mshc2 = &mshc_2;
- };
-
- chosen {
- stdout-path = &serial_1;
- };
-
- memory at 20000000 {
- device_type = "memory";
- reg = <0x0 0x20000000 0x0 0xc0000000>;
- };
-
- gpio-keys {
- compatible = "gpio-keys";
-
- power-key {
- gpios = <&gpa2 7 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_POWER>;
- label = "power key";
- debounce-interval = <10>;
- };
-
- volume-up-key {
- gpios = <&gpa2 0 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_VOLUMEUP>;
- label = "volume-up key";
- debounce-interval = <10>;
- };
-
- volume-down-key {
- gpios = <&gpa2 1 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_VOLUMEDOWN>;
- label = "volume-down key";
- debounce-interval = <10>;
- };
-
- homepage-key {
- gpios = <&gpa0 3 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_MENU>;
- label = "homepage key";
- debounce-interval = <10>;
- };
- };
-
- i2c_max98504: i2c-gpio-0 {
- compatible = "i2c-gpio";
- gpios = <&gpd0 1 GPIO_ACTIVE_HIGH /* SPK_AMP_SDA */
- &gpd0 0 GPIO_ACTIVE_HIGH /* SPK_AMP_SCL */ >;
- i2c-gpio,delay-us = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- max98504: max98504 at 31 {
- compatible = "maxim,max98504";
- reg = <0x31>;
- maxim,rx-path = <1>;
- maxim,tx-path = <1>;
- maxim,tx-channel-mask = <3>;
- maxim,tx-channel-source = <2>;
- };
- };
-
- sound {
- compatible = "samsung,tm2-audio";
- audio-codec = <&wm5110>;
- i2s-controller = <&i2s0>;
- audio-amplifier = <&max98504>;
- mic-bias-gpios = <&gpr3 2 GPIO_ACTIVE_HIGH>;
- model = "wm5110";
- samsung,audio-routing =
- /* Headphone */
- "HP", "HPOUT1L",
- "HP", "HPOUT1R",
-
- /* Speaker */
- "SPK", "SPKOUT",
- "SPKOUT", "HPOUT2L",
- "SPKOUT", "HPOUT2R",
-
- /* Receiver */
- "RCV", "HPOUT3L",
- "RCV", "HPOUT3R";
- status = "okay";
- };
-};
-
-&adc {
- vdd-supply = <&ldo3_reg>;
- status = "okay";
-
- thermistor-ap {
- compatible = "murata,ncp03wf104";
- pullup-uv = <1800000>;
- pullup-ohm = <100000>;
- pulldown-ohm = <0>;
- io-channels = <&adc 0>;
- };
-
- thermistor-battery {
- compatible = "murata,ncp03wf104";
- pullup-uv = <1800000>;
- pullup-ohm = <100000>;
- pulldown-ohm = <0>;
- io-channels = <&adc 1>;
- #thermal-sensor-cells = <0>;
- };
-
- thermistor-charger {
- compatible = "murata,ncp03wf104";
- pullup-uv = <1800000>;
- pullup-ohm = <100000>;
- pulldown-ohm = <0>;
- io-channels = <&adc 2>;
- };
-};
-
-&bus_g2d_400 {
- devfreq-events = <&ppmu_event0_d0_general>, <&ppmu_event0_d1_general>;
- vdd-supply = <&buck4_reg>;
- exynos,saturation-ratio = <10>;
- status = "okay";
-};
-
-&bus_g2d_266 {
- devfreq = <&bus_g2d_400>;
- status = "okay";
-};
-
-&bus_gscl {
- devfreq = <&bus_g2d_400>;
- status = "okay";
-};
-
-&bus_hevc {
- devfreq = <&bus_g2d_400>;
- status = "okay";
-};
-
-&bus_jpeg {
- devfreq = <&bus_g2d_400>;
- status = "okay";
-};
-
-&bus_mfc {
- devfreq = <&bus_g2d_400>;
- status = "okay";
-};
-
-&bus_mscl {
- devfreq = <&bus_g2d_400>;
- status = "okay";
-};
-
-&bus_noc0 {
- devfreq = <&bus_g2d_400>;
- status = "okay";
-};
-
-&bus_noc1 {
- devfreq = <&bus_g2d_400>;
- status = "okay";
-};
-
-&bus_noc2 {
- devfreq = <&bus_g2d_400>;
- status = "okay";
-};
-
-&cmu_aud {
- assigned-clocks = <&cmu_aud CLK_MOUT_AUD_PLL_USER>;
- assigned-clock-parents = <&cmu_top CLK_FOUT_AUD_PLL>;
-};
-
-&cmu_fsys {
- assigned-clocks = <&cmu_top CLK_MOUT_SCLK_USBDRD30>,
- <&cmu_top CLK_MOUT_SCLK_USBHOST30>,
- <&cmu_fsys CLK_MOUT_SCLK_USBDRD30_USER>,
- <&cmu_fsys CLK_MOUT_SCLK_USBHOST30_USER>,
- <&cmu_fsys CLK_MOUT_PHYCLK_USBDRD30_UDRD30_PIPE_PCLK_USER>,
- <&cmu_fsys CLK_MOUT_PHYCLK_USBHOST30_UHOST30_PIPE_PCLK_USER>,
- <&cmu_fsys CLK_MOUT_PHYCLK_USBDRD30_UDRD30_PHYCLOCK_USER>,
- <&cmu_fsys CLK_MOUT_PHYCLK_USBHOST30_UHOST30_PHYCLOCK_USER>,
- <&cmu_top CLK_DIV_SCLK_USBDRD30>,
- <&cmu_top CLK_DIV_SCLK_USBHOST30>;
- assigned-clock-parents = <&cmu_top CLK_MOUT_BUS_PLL_USER>,
- <&cmu_top CLK_MOUT_BUS_PLL_USER>,
- <&cmu_top CLK_SCLK_USBDRD30_FSYS>,
- <&cmu_top CLK_SCLK_USBHOST30_FSYS>,
- <&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PIPE_PCLK_PHY>,
- <&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PIPE_PCLK_PHY>,
- <&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PHYCLOCK_PHY>,
- <&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PHYCLOCK_PHY>;
- assigned-clock-rates = <0>, <0>, <0>, <0>, <0>, <0>, <0>, <0>,
- <66700000>, <66700000>;
-};
-
-&cmu_gscl {
- assigned-clocks = <&cmu_gscl CLK_MOUT_ACLK_GSCL_111_USER>,
- <&cmu_gscl CLK_MOUT_ACLK_GSCL_333_USER>;
- assigned-clock-parents = <&cmu_top CLK_ACLK_GSCL_111>,
- <&cmu_top CLK_ACLK_GSCL_333>;
-};
-
-&cmu_mfc {
- assigned-clocks = <&cmu_mfc CLK_MOUT_ACLK_MFC_400_USER>;
- assigned-clock-parents = <&cmu_top CLK_ACLK_MFC_400>;
-};
-
-&cmu_mscl {
- assigned-clocks = <&cmu_mscl CLK_MOUT_ACLK_MSCL_400_USER>,
- <&cmu_mscl CLK_MOUT_SCLK_JPEG_USER>,
- <&cmu_mscl CLK_MOUT_SCLK_JPEG>,
- <&cmu_top CLK_MOUT_SCLK_JPEG_A>;
- assigned-clock-parents = <&cmu_top CLK_ACLK_MSCL_400>,
- <&cmu_top CLK_SCLK_JPEG_MSCL>,
- <&cmu_mscl CLK_MOUT_SCLK_JPEG_USER>,
- <&cmu_top CLK_MOUT_BUS_PLL_USER>;
-};
-
-&cpu0 {
- cpu-supply = <&buck3_reg>;
-};
-
-&cpu4 {
- cpu-supply = <&buck2_reg>;
-};
-
-&decon {
- status = "okay";
-
- i80-if-timings {
- };
-};
-
-&dsi {
- status = "okay";
- vddcore-supply = <&ldo6_reg>;
- vddio-supply = <&ldo7_reg>;
- samsung,pll-clock-frequency = <24000000>;
- pinctrl-names = "default";
- pinctrl-0 = <&te_irq>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port at 1 {
- reg = <1>;
-
- dsi_out: endpoint {
- samsung,burst-clock-frequency = <512000000>;
- samsung,esc-clock-frequency = <16000000>;
- };
- };
- };
-};
-
-&hsi2c_0 {
- status = "okay";
- clock-frequency = <2500000>;
-
- s2mps13-pmic at 66 {
- compatible = "samsung,s2mps13-pmic";
- interrupt-parent = <&gpa0>;
- interrupts = <7 IRQ_TYPE_NONE>;
- reg = <0x66>;
- samsung,s2mps11-wrstbi-ground;
-
- s2mps13_osc: clocks {
- compatible = "samsung,s2mps13-clk";
- #clock-cells = <1>;
- clock-output-names = "s2mps13_ap", "s2mps13_cp",
- "s2mps13_bt";
- };
-
- regulators {
- ldo1_reg: LDO1 {
- regulator-name = "VDD_ALIVE_0.9V_AP";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <900000>;
- regulator-always-on;
- };
-
- ldo2_reg: LDO2 {
- regulator-name = "VDDQ_MMC2_2.8V_AP";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo3_reg: LDO3 {
- regulator-name = "VDD1_E_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo4_reg: LDO4 {
- regulator-name = "VDD10_MIF_PLL_1.0V_AP";
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo5_reg: LDO5 {
- regulator-name = "VDD10_DPLL_1.0V_AP";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo6_reg: LDO6 {
- regulator-name = "VDD10_MIPI2L_1.0V_AP";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo7_reg: LDO7 {
- regulator-name = "VDD18_MIPI2L_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo8_reg: LDO8 {
- regulator-name = "VDD18_LLI_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo9_reg: LDO9 {
- regulator-name = "VDD18_ABB_ETC_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo10_reg: LDO10 {
- regulator-name = "VDD33_USB30_3.0V_AP";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo11_reg: LDO11 {
- regulator-name = "VDD_INT_M_1.0V_AP";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo12_reg: LDO12 {
- regulator-name = "VDD_KFC_M_1.1V_AP";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- };
-
- ldo13_reg: LDO13 {
- regulator-name = "VDD_G3D_M_0.95V_AP";
- regulator-min-microvolt = <950000>;
- regulator-max-microvolt = <950000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo14_reg: LDO14 {
- regulator-name = "VDDQ_M1_LDO_1.2V_AP";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo15_reg: LDO15 {
- regulator-name = "VDDQ_M2_LDO_1.2V_AP";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo16_reg: LDO16 {
- regulator-name = "VDDQ_EFUSE";
- regulator-min-microvolt = <1400000>;
- regulator-max-microvolt = <3400000>;
- regulator-always-on;
- };
-
- ldo17_reg: LDO17 {
- regulator-name = "V_TFLASH_2.8V_AP";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- ldo18_reg: LDO18 {
- regulator-name = "V_CODEC_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo19_reg: LDO19 {
- regulator-name = "VDDA_1.8V_COMP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo20_reg: LDO20 {
- regulator-name = "VCC_2.8V_AP";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- };
-
- ldo21_reg: LDO21 {
- regulator-name = "VT_CAM_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo22_reg: LDO22 {
- regulator-name = "CAM_IO_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo23_reg: LDO23 {
- regulator-name = "CAM_SEN_CORE_1.05V_AP";
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1050000>;
- };
-
- ldo24_reg: LDO24 {
- regulator-name = "VT_CAM_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- ldo25_reg: LDO25 {
- regulator-name = "UNUSED_LDO25";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-off;
- };
-
- ldo26_reg: LDO26 {
- regulator-name = "CAM_AF_2.8V_AP";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- ldo27_reg: LDO27 {
- regulator-name = "VCC_3.0V_LCD_AP";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- ldo28_reg: LDO28 {
- regulator-name = "VCC_1.8V_LCD_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo29_reg: LDO29 {
- regulator-name = "VT_CAM_2.8V";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- ldo30_reg: LDO30 {
- regulator-name = "TSP_AVDD_3.3V_AP";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- ldo31_reg: LDO31 {
- regulator-name = "TSP_VDD_1.85V_AP";
- regulator-min-microvolt = <1850000>;
- regulator-max-microvolt = <1850000>;
- };
-
- ldo32_reg: LDO32 {
- regulator-name = "VTOUCH_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo33_reg: LDO33 {
- regulator-name = "VTOUCH_LED_3.3V";
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <3300000>;
- regulator-ramp-delay = <12500>;
- };
-
- ldo34_reg: LDO34 {
- regulator-name = "VCC_1.8V_MHL_AP";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <2100000>;
- };
-
- ldo35_reg: LDO35 {
- regulator-name = "OIS_VM_2.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- ldo36_reg: LDO36 {
- regulator-name = "VSIL_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- };
-
- ldo37_reg: LDO37 {
- regulator-name = "VF_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo38_reg: LDO38 {
- regulator-name = "VCC_3.0V_MOTOR_AP";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- ldo39_reg: LDO39 {
- regulator-name = "V_HRM_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo40_reg: LDO40 {
- regulator-name = "V_HRM_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- buck1_reg: BUCK1 {
- regulator-name = "VDD_MIF_0.9V_AP";
- regulator-min-microvolt = <600000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck2_reg: BUCK2 {
- regulator-name = "VDD_EGL_1.0V_AP";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1300000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck3_reg: BUCK3 {
- regulator-name = "VDD_KFC_1.0V_AP";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck4_reg: BUCK4 {
- regulator-name = "VDD_INT_0.95V_AP";
- regulator-min-microvolt = <600000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck5_reg: BUCK5 {
- regulator-name = "VDD_DISP_CAM0_0.9V_AP";
- regulator-min-microvolt = <600000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck6_reg: BUCK6 {
- regulator-name = "VDD_G3D_0.9V_AP";
- regulator-min-microvolt = <600000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck7_reg: BUCK7 {
- regulator-name = "VDD_MEM1_1.2V_AP";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- buck8_reg: BUCK8 {
- regulator-name = "VDD_LLDO_1.35V_AP";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- buck9_reg: BUCK9 {
- regulator-name = "VDD_MLDO_2.0V_AP";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- buck10_reg: BUCK10 {
- regulator-name = "vdd_mem2";
- regulator-min-microvolt = <550000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- };
- };
- };
-};
-
-&hsi2c_8 {
- status = "okay";
-
- max77843 at 66 {
- compatible = "maxim,max77843";
- interrupt-parent = <&gpa1>;
- interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
- reg = <0x66>;
-
- muic: max77843-muic {
- compatible = "maxim,max77843-muic";
- };
-
- regulators {
- compatible = "maxim,max77843-regulator";
- safeout1_reg: SAFEOUT1 {
- regulator-name = "SAFEOUT1";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <4950000>;
- };
-
- safeout2_reg: SAFEOUT2 {
- regulator-name = "SAFEOUT2";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <4950000>;
- };
-
- charger_reg: CHARGER {
- regulator-name = "CHARGER";
- regulator-min-microamp = <100000>;
- regulator-max-microamp = <3150000>;
- };
- };
-
- haptic: max77843-haptic {
- compatible = "maxim,max77843-haptic";
- haptic-supply = <&ldo38_reg>;
- pwms = <&pwm 0 33670 0>;
- pwm-names = "haptic";
- };
- };
-};
-
-&i2s0 {
- status = "okay";
-};
-
-&mshc_0 {
- status = "okay";
- num-slots = <1>;
- mmc-hs200-1_8v;
- mmc-hs400-1_8v;
- cap-mmc-highspeed;
- non-removable;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <0 4>;
- samsung,dw-mshc-ddr-timing = <0 2>;
- samsung,dw-mshc-hs400-timing = <0 3>;
- samsung,read-strobe-delay = <90>;
- fifo-depth = <0x80>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_qrdy &sd0_bus1 &sd0_bus4
- &sd0_bus8 &sd0_rdqs>;
- bus-width = <8>;
- assigned-clocks = <&cmu_top CLK_SCLK_MMC0_FSYS>;
- assigned-clock-rates = <800000000>;
-};
-
-&mshc_2 {
- status = "okay";
- num-slots = <1>;
- cap-sd-highspeed;
- disable-wp;
- cd-gpios = <&gpa2 4 GPIO_ACTIVE_HIGH>;
- cd-inverted;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <0 4>;
- samsung,dw-mshc-ddr-timing = <0 2>;
- fifo-depth = <0x80>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus1 &sd2_bus4>;
- bus-width = <4>;
-};
-
-&ppmu_d0_general {
- status = "okay";
- events {
- ppmu_event0_d0_general: ppmu-event0-d0-general {
- event-name = "ppmu-event0-d0-general";
- };
- };
-};
-
-&ppmu_d1_general {
- status = "okay";
- events {
- ppmu_event0_d1_general: ppmu-event0-d1-general {
- event-name = "ppmu-event0-d1-general";
- };
- };
-};
-
-&pinctrl_alive {
- pinctrl-names = "default";
- pinctrl-0 = <&initial_alive>;
-
- initial_alive: initial-state {
- PIN(INPUT, gpa0-0, DOWN, FAST_SR1);
- PIN(INPUT, gpa0-1, NONE, FAST_SR1);
- PIN(INPUT, gpa0-2, DOWN, FAST_SR1);
- PIN(INPUT, gpa0-3, NONE, FAST_SR1);
- PIN(INPUT, gpa0-4, NONE, FAST_SR1);
- PIN(INPUT, gpa0-5, DOWN, FAST_SR1);
- PIN(INPUT, gpa0-6, NONE, FAST_SR1);
- PIN(INPUT, gpa0-7, NONE, FAST_SR1);
-
- PIN(INPUT, gpa1-0, UP, FAST_SR1);
- PIN(INPUT, gpa1-1, NONE, FAST_SR1);
- PIN(INPUT, gpa1-2, NONE, FAST_SR1);
- PIN(INPUT, gpa1-3, DOWN, FAST_SR1);
- PIN(INPUT, gpa1-4, DOWN, FAST_SR1);
- PIN(INPUT, gpa1-5, NONE, FAST_SR1);
- PIN(INPUT, gpa1-6, NONE, FAST_SR1);
- PIN(INPUT, gpa1-7, NONE, FAST_SR1);
-
- PIN(INPUT, gpa2-0, NONE, FAST_SR1);
- PIN(INPUT, gpa2-1, NONE, FAST_SR1);
- PIN(INPUT, gpa2-2, NONE, FAST_SR1);
- PIN(INPUT, gpa2-3, DOWN, FAST_SR1);
- PIN(INPUT, gpa2-4, NONE, FAST_SR1);
- PIN(INPUT, gpa2-5, DOWN, FAST_SR1);
- PIN(INPUT, gpa2-6, DOWN, FAST_SR1);
- PIN(INPUT, gpa2-7, NONE, FAST_SR1);
-
- PIN(INPUT, gpa3-0, DOWN, FAST_SR1);
- PIN(INPUT, gpa3-1, DOWN, FAST_SR1);
- PIN(INPUT, gpa3-2, NONE, FAST_SR1);
- PIN(INPUT, gpa3-3, DOWN, FAST_SR1);
- PIN(INPUT, gpa3-4, NONE, FAST_SR1);
- PIN(INPUT, gpa3-5, DOWN, FAST_SR1);
- PIN(INPUT, gpa3-6, DOWN, FAST_SR1);
- PIN(INPUT, gpa3-7, DOWN, FAST_SR1);
-
- PIN(INPUT, gpf1-0, NONE, FAST_SR1);
- PIN(INPUT, gpf1-1, NONE, FAST_SR1);
- PIN(INPUT, gpf1-2, DOWN, FAST_SR1);
- PIN(INPUT, gpf1-4, UP, FAST_SR1);
- PIN(OUTPUT, gpf1-5, NONE, FAST_SR1);
- PIN(INPUT, gpf1-6, DOWN, FAST_SR1);
- PIN(INPUT, gpf1-7, DOWN, FAST_SR1);
-
- PIN(INPUT, gpf2-0, DOWN, FAST_SR1);
- PIN(INPUT, gpf2-1, DOWN, FAST_SR1);
- PIN(INPUT, gpf2-2, DOWN, FAST_SR1);
- PIN(INPUT, gpf2-3, DOWN, FAST_SR1);
-
- PIN(INPUT, gpf3-0, DOWN, FAST_SR1);
- PIN(INPUT, gpf3-1, DOWN, FAST_SR1);
- PIN(INPUT, gpf3-2, NONE, FAST_SR1);
- PIN(INPUT, gpf3-3, DOWN, FAST_SR1);
-
- PIN(INPUT, gpf4-0, DOWN, FAST_SR1);
- PIN(INPUT, gpf4-1, DOWN, FAST_SR1);
- PIN(INPUT, gpf4-2, DOWN, FAST_SR1);
- PIN(INPUT, gpf4-3, DOWN, FAST_SR1);
- PIN(INPUT, gpf4-4, DOWN, FAST_SR1);
- PIN(INPUT, gpf4-5, DOWN, FAST_SR1);
- PIN(INPUT, gpf4-6, DOWN, FAST_SR1);
- PIN(INPUT, gpf4-7, DOWN, FAST_SR1);
-
- PIN(INPUT, gpf5-0, DOWN, FAST_SR1);
- PIN(INPUT, gpf5-1, DOWN, FAST_SR1);
- PIN(INPUT, gpf5-2, DOWN, FAST_SR1);
- PIN(INPUT, gpf5-3, DOWN, FAST_SR1);
- PIN(OUTPUT, gpf5-4, NONE, FAST_SR1);
- PIN(INPUT, gpf5-5, DOWN, FAST_SR1);
- PIN(INPUT, gpf5-6, DOWN, FAST_SR1);
- PIN(INPUT, gpf5-7, DOWN, FAST_SR1);
- };
-
- te_irq: te_irq {
- samsung,pins = "gpf1-3";
- samsung,pin-function = <0xf>;
- };
-};
-
-&pinctrl_cpif {
- pinctrl-names = "default";
- pinctrl-0 = <&initial_cpif>;
-
- initial_cpif: initial-state {
- PIN(INPUT, gpv6-0, DOWN, FAST_SR1);
- PIN(INPUT, gpv6-1, DOWN, FAST_SR1);
- };
-};
-
-&pinctrl_ese {
- pinctrl-names = "default";
- pinctrl-0 = <&initial_ese>;
-
- initial_ese: initial-state {
- PIN(INPUT, gpj2-0, DOWN, FAST_SR1);
- PIN(INPUT, gpj2-1, DOWN, FAST_SR1);
- PIN(INPUT, gpj2-2, DOWN, FAST_SR1);
- };
-};
-
-&pinctrl_fsys {
- pinctrl-names = "default";
- pinctrl-0 = <&initial_fsys>;
-
- initial_fsys: initial-state {
- PIN(INPUT, gpr3-0, NONE, FAST_SR1);
- PIN(INPUT, gpr3-1, DOWN, FAST_SR1);
- PIN(INPUT, gpr3-2, DOWN, FAST_SR1);
- PIN(INPUT, gpr3-3, DOWN, FAST_SR1);
- PIN(INPUT, gpr3-7, NONE, FAST_SR1);
- };
-};
-
-&pinctrl_imem {
- pinctrl-names = "default";
- pinctrl-0 = <&initial_imem>;
-
- initial_imem: initial-state {
- PIN(INPUT, gpf0-0, UP, FAST_SR1);
- PIN(INPUT, gpf0-1, UP, FAST_SR1);
- PIN(INPUT, gpf0-2, DOWN, FAST_SR1);
- PIN(INPUT, gpf0-3, UP, FAST_SR1);
- PIN(INPUT, gpf0-4, DOWN, FAST_SR1);
- PIN(INPUT, gpf0-5, NONE, FAST_SR1);
- PIN(INPUT, gpf0-6, DOWN, FAST_SR1);
- PIN(INPUT, gpf0-7, UP, FAST_SR1);
- };
-};
-
-&pinctrl_nfc {
- pinctrl-names = "default";
- pinctrl-0 = <&initial_nfc>;
-
- initial_nfc: initial-state {
- PIN(INPUT, gpj0-2, DOWN, FAST_SR1);
- };
-};
-
-&pinctrl_peric {
- pinctrl-names = "default";
- pinctrl-0 = <&initial_peric>;
-
- initial_peric: initial-state {
- PIN(INPUT, gpv7-0, DOWN, FAST_SR1);
- PIN(INPUT, gpv7-1, DOWN, FAST_SR1);
- PIN(INPUT, gpv7-2, NONE, FAST_SR1);
- PIN(INPUT, gpv7-3, DOWN, FAST_SR1);
- PIN(INPUT, gpv7-4, DOWN, FAST_SR1);
- PIN(INPUT, gpv7-5, DOWN, FAST_SR1);
-
- PIN(INPUT, gpb0-4, DOWN, FAST_SR1);
-
- PIN(INPUT, gpc0-2, DOWN, FAST_SR1);
- PIN(INPUT, gpc0-5, DOWN, FAST_SR1);
- PIN(INPUT, gpc0-7, DOWN, FAST_SR1);
-
- PIN(INPUT, gpc1-1, DOWN, FAST_SR1);
-
- PIN(INPUT, gpc3-4, NONE, FAST_SR1);
- PIN(INPUT, gpc3-5, NONE, FAST_SR1);
- PIN(INPUT, gpc3-6, NONE, FAST_SR1);
- PIN(INPUT, gpc3-7, NONE, FAST_SR1);
-
- PIN(OUTPUT, gpg0-0, NONE, FAST_SR1);
- PIN(2, gpg0-1, DOWN, FAST_SR1);
-
- PIN(INPUT, gpd2-5, DOWN, FAST_SR1);
-
- PIN(INPUT, gpd4-0, NONE, FAST_SR1);
- PIN(INPUT, gpd4-1, DOWN, FAST_SR1);
- PIN(INPUT, gpd4-2, DOWN, FAST_SR1);
- PIN(INPUT, gpd4-3, DOWN, FAST_SR1);
- PIN(INPUT, gpd4-4, DOWN, FAST_SR1);
-
- PIN(INPUT, gpd6-3, DOWN, FAST_SR1);
-
- PIN(INPUT, gpd8-1, UP, FAST_SR1);
-
- PIN(INPUT, gpg1-0, DOWN, FAST_SR1);
- PIN(INPUT, gpg1-1, DOWN, FAST_SR1);
- PIN(INPUT, gpg1-2, DOWN, FAST_SR1);
- PIN(INPUT, gpg1-3, DOWN, FAST_SR1);
- PIN(INPUT, gpg1-4, DOWN, FAST_SR1);
-
- PIN(INPUT, gpg2-0, DOWN, FAST_SR1);
- PIN(INPUT, gpg2-1, DOWN, FAST_SR1);
-
- PIN(INPUT, gpg3-0, DOWN, FAST_SR1);
- PIN(INPUT, gpg3-1, DOWN, FAST_SR1);
- PIN(INPUT, gpg3-5, DOWN, FAST_SR1);
- PIN(INPUT, gpg3-7, DOWN, FAST_SR1);
- };
-};
-
-&pinctrl_touch {
- pinctrl-names = "default";
- pinctrl-0 = <&initial_touch>;
-
- initial_touch: initial-state {
- PIN(INPUT, gpj1-2, DOWN, FAST_SR1);
- };
-};
-
-&pwm {
- pinctrl-0 = <&pwm0_out>;
- pinctrl-names = "default";
- status = "okay";
-};
-
-&mic {
- status = "okay";
-
- i80-if-timings {
- };
-};
-
-&pmu_system_controller {
- assigned-clocks = <&pmu_system_controller 0>;
- assigned-clock-parents = <&xxti>;
-};
-
-&serial_1 {
- status = "okay";
-};
-
-&spi_1 {
- cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>;
- status = "okay";
-
- wm5110: wm5110-codec at 0 {
- compatible = "wlf,wm5110";
- reg = <0x0>;
- spi-max-frequency = <20000000>;
- interrupt-parent = <&gpa0>;
- interrupts = <4 IRQ_TYPE_NONE>;
- clocks = <&pmu_system_controller 0>,
- <&s2mps13_osc S2MPS11_CLK_BT>;
- clock-names = "mclk1", "mclk2";
-
- gpio-controller;
- #gpio-cells = <2>;
-
- wlf,micd-detect-debounce = <300>;
- wlf,micd-bias-start-time = <0x1>;
- wlf,micd-rate = <0x7>;
- wlf,micd-dbtime = <0x1>;
- wlf,micd-force-micbias;
- wlf,micd-configs = <0x0 1 0>;
- wlf,hpdet-channel = <1>;
- wlf,gpsw = <0x1>;
- wlf,inmode = <2 0 2 0>;
-
- wlf,reset = <&gpc0 7 GPIO_ACTIVE_HIGH>;
- wlf,ldoena = <&gpf0 0 GPIO_ACTIVE_HIGH>;
-
- /* core supplies */
- AVDD-supply = <&ldo18_reg>;
- DBVDD1-supply = <&ldo18_reg>;
- CPVDD-supply = <&ldo18_reg>;
- DBVDD2-supply = <&ldo18_reg>;
- DBVDD3-supply = <&ldo18_reg>;
-
- controller-data {
- samsung,spi-feedback-delay = <0>;
- };
- };
-};
-
-&timer {
- clock-frequency = <24000000>;
-};
-
-&tmu_atlas0 {
- vtmu-supply = <&ldo3_reg>;
- status = "okay";
-};
-
-&tmu_apollo {
- vtmu-supply = <&ldo3_reg>;
- status = "okay";
-};
-
-&tmu_g3d {
- vtmu-supply = <&ldo3_reg>;
- status = "okay";
-};
-
-&usbdrd30 {
- vdd33-supply = <&ldo10_reg>;
- vdd10-supply = <&ldo6_reg>;
- status = "okay";
-};
-
-&usbdrd_dwc3_0 {
- dr_mode = "otg";
-};
-
-&usbdrd30_phy {
- vbus-supply = <&safeout1_reg>;
- status = "okay";
-};
-
-&xxti {
- clock-frequency = <24000000>;
-};
+/*
+ * SAMSUNG Exynos5433 TM2 board device tree source
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ *
+ * Device tree source file for Samsung's TM2 board which is based on
+ * Samsung Exynos5433 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "exynos5433-tm2-common.dtsi"
+
+/ {
+ model = "Samsung TM2E board";
+ compatible = "samsung,tm2e", "samsung,exynos5433";
+};
+
+®ulators {
+ ldo31_reg: LDO31 {
+ regulator-name = "TSP_VDD_1.85V_AP";
+ regulator-min-microvolt = <1850000>;
+ regulator-max-microvolt = <1850000>;
+ };
+
+ ldo38_reg: LDO38 {
+ regulator-name = "VCC_3.0V_MOTOR_AP";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+};
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts
index 854c583..53e361f 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts
@@ -11,21 +11,23 @@
* published by the Free Software Foundation.
*/
-#include "exynos5433-tm2.dts"
+#include "exynos5433-tm2-common.dtsi"
/ {
model = "Samsung TM2E board";
compatible = "samsung,tm2e", "samsung,exynos5433";
};
-&ldo31_reg {
- regulator-name = "TSP_VDD_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-};
+®ulators {
+ ldo31_reg: LDO31 {
+ regulator-name = "TSP_VDD_1.8V_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
-&ldo38_reg {
- regulator-name = "VCC_3.3V_MOTOR_AP";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
+ ldo38_reg: LDO38 {
+ regulator-name = "VCC_3.3V_MOTOR_AP";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
};
--
2.7.4
^ permalink raw reply related
* [PATCH v3 3/5] input: Add support for the tm2 touchkey device driver
From: Jaechul Lee @ 2017-01-06 3:59 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483675149-32598-1-git-send-email-jcsing.lee@samsung.com>
This patch adds the binding description of the tm2 touchkey
device driver.
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
---
.../bindings/input/samsung,tm2-touchkey.txt | 27 ++++++++++++++++++++++
1 file changed, 27 insertions(+)
create mode 100644 Documentation/devicetree/bindings/input/samsung,tm2-touchkey.txt
diff --git a/Documentation/devicetree/bindings/input/samsung,tm2-touchkey.txt b/Documentation/devicetree/bindings/input/samsung,tm2-touchkey.txt
new file mode 100644
index 0000000..4de1af0
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/samsung,tm2-touchkey.txt
@@ -0,0 +1,27 @@
+Samsung tm2-touchkey
+
+Required properties:
+- compatible: must be "samsung,tm2-touchkey"
+- reg: I2C address of the chip.
+- interrupt-parent: a phandle for the interrupt controller (see interrupt
+ binding[0]).
+- interrupts: interrupt to which the chip is connected (see interrupt
+ binding[0]).
+- vcc-supply : internal regulator output. 1.8V
+- vdd-supply : power supply for IC 3.3V
+
+[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+
+Example:
+ &i2c0 {
+ /* ... */
+
+ touchkey at 20 {
+ compatible = "samsung,tm2-touchkey";
+ reg = <0x20>;
+ interrupt-parent = <&gpa3>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+ vcc-supply=<&ldo32_reg>;
+ vdd-supply=<&ldo33_reg>;
+ };
+ };
--
2.7.4
^ permalink raw reply related
* [PATCH v3 4/5] input: tm2-touchkey: Add touchkey driver support for TM2
From: Jaechul Lee @ 2017-01-06 3:59 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483675149-32598-1-git-send-email-jcsing.lee@samsung.com>
This patch adds support for the TM2 touch key and led
functionality.
The driver interfaces with userspace through an input device and
reports KEY_PHONE and KEY_BACK event types. LED brightness can be
controlled by "/sys/class/leds/tm2-touchkey/brightness".
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
---
drivers/input/keyboard/Kconfig | 11 ++
drivers/input/keyboard/Makefile | 1 +
drivers/input/keyboard/tm2-touchkey.c | 280 ++++++++++++++++++++++++++++++++++
3 files changed, 292 insertions(+)
create mode 100644 drivers/input/keyboard/tm2-touchkey.c
diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig
index cbd75cf..e6e9858 100644
--- a/drivers/input/keyboard/Kconfig
+++ b/drivers/input/keyboard/Kconfig
@@ -666,6 +666,17 @@ config KEYBOARD_TC3589X
To compile this driver as a module, choose M here: the
module will be called tc3589x-keypad.
+config KEYBOARD_TM2_TOUCHKEY
+ tristate "tm2-touchkey support"
+ depends on I2C
+ depends on LEDS_CLASS
+ help
+ Say Y here to enable device driver for tm2-touchkey with
+ LED control for the Exynos5433 TM2 board.
+
+ To compile this driver as a module, choose M here.
+ module will be called tm2-touchkey.
+
config KEYBOARD_TWL4030
tristate "TI TWL4030/TWL5030/TPS659x0 keypad support"
depends on TWL4030_CORE
diff --git a/drivers/input/keyboard/Makefile b/drivers/input/keyboard/Makefile
index d9f4cfc..7d9acff 100644
--- a/drivers/input/keyboard/Makefile
+++ b/drivers/input/keyboard/Makefile
@@ -61,6 +61,7 @@ obj-$(CONFIG_KEYBOARD_SUN4I_LRADC) += sun4i-lradc-keys.o
obj-$(CONFIG_KEYBOARD_SUNKBD) += sunkbd.o
obj-$(CONFIG_KEYBOARD_TC3589X) += tc3589x-keypad.o
obj-$(CONFIG_KEYBOARD_TEGRA) += tegra-kbc.o
+obj-$(CONFIG_KEYBOARD_TM2_TOUCHKEY) += tm2-touchkey.o
obj-$(CONFIG_KEYBOARD_TWL4030) += twl4030_keypad.o
obj-$(CONFIG_KEYBOARD_XTKBD) += xtkbd.o
obj-$(CONFIG_KEYBOARD_W90P910) += w90p910_keypad.o
diff --git a/drivers/input/keyboard/tm2-touchkey.c b/drivers/input/keyboard/tm2-touchkey.c
new file mode 100644
index 0000000..92eacb6
--- /dev/null
+++ b/drivers/input/keyboard/tm2-touchkey.c
@@ -0,0 +1,280 @@
+/*
+ * TM2 touchkey device driver
+ *
+ * Copyright 2005 Phil Blundell
+ * Copyright 2016 Samsung Electronics Co., Ltd.
+ *
+ * Author: Beomho Seo <beomho.seo@samsung.com>
+ * Author: Jaechul Lee <jcsing.lee@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/bitops.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/i2c.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/leds.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/pm.h>
+#include <linux/regulator/consumer.h>
+
+#define TM2_TOUCHKEY_DEV_NAME "tm2-touchkey"
+#define TM2_TOUCHKEY_KEYCODE_REG 0x03
+#define TM2_TOUCHKEY_BASE_REG 0x00
+#define TM2_TOUCHKEY_CMD_LED_ON 0x10
+#define TM2_TOUCHKEY_CMD_LED_OFF 0x20
+#define TM2_TOUCHKEY_BIT_PRESS_EV BIT(3)
+#define TM2_TOUCHKEY_BIT_KEYCODE GENMASK(2, 0)
+#define TM2_TOUCHKEY_LED_VOLTAGE_MIN 2500000
+#define TM2_TOUCHKEY_LED_VOLTAGE_MAX 3300000
+
+enum {
+ TM2_TOUCHKEY_KEY_MENU = 0x1,
+ TM2_TOUCHKEY_KEY_BACK,
+};
+
+struct tm2_touchkey_data {
+ struct i2c_client *client;
+ struct input_dev *input_dev;
+ struct led_classdev led_dev;
+ struct regulator_bulk_data regulators[2];
+
+ u8 keycode_type;
+ u8 pressed;
+};
+
+static void tm2_touchkey_led_brightness_set(struct led_classdev *led_dev,
+ enum led_brightness brightness)
+{
+ struct tm2_touchkey_data *touchkey =
+ container_of(led_dev, struct tm2_touchkey_data, led_dev);
+ u32 volt;
+ u8 data;
+
+ if (brightness == LED_OFF) {
+ volt = TM2_TOUCHKEY_LED_VOLTAGE_MIN;
+ data = TM2_TOUCHKEY_CMD_LED_OFF;
+ } else {
+ volt = TM2_TOUCHKEY_LED_VOLTAGE_MAX;
+ data = TM2_TOUCHKEY_CMD_LED_ON;
+ }
+
+ regulator_set_voltage(touchkey->regulators[1].consumer, volt, volt);
+ i2c_smbus_write_byte_data(touchkey->client,
+ TM2_TOUCHKEY_BASE_REG, data);
+}
+
+static int tm2_touchkey_power_enable(struct tm2_touchkey_data *touchkey)
+{
+ int ret = 0;
+
+ ret = regulator_bulk_enable(ARRAY_SIZE(touchkey->regulators),
+ touchkey->regulators);
+ if (ret)
+ return ret;
+
+ /* waiting for device initialization, at least 150ms */
+ msleep(150);
+
+ return 0;
+}
+
+static void tm2_touchkey_power_disable(void *data)
+{
+ struct tm2_touchkey_data *touchkey = data;
+
+ regulator_bulk_disable(ARRAY_SIZE(touchkey->regulators),
+ touchkey->regulators);
+}
+
+static irqreturn_t tm2_touchkey_irq_handler(int irq, void *devid)
+{
+ struct tm2_touchkey_data *touchkey = devid;
+ u32 data;
+
+ data = i2c_smbus_read_byte_data(touchkey->client,
+ TM2_TOUCHKEY_KEYCODE_REG);
+
+ if (data < 0) {
+ dev_err(&touchkey->client->dev, "Failed to read i2c data\n");
+ return IRQ_HANDLED;
+ }
+
+ touchkey->keycode_type = data & TM2_TOUCHKEY_BIT_KEYCODE;
+ touchkey->pressed = !(data & TM2_TOUCHKEY_BIT_PRESS_EV);
+
+ if (touchkey->keycode_type != TM2_TOUCHKEY_KEY_MENU &&
+ touchkey->keycode_type != TM2_TOUCHKEY_KEY_BACK) {
+ dev_warn(&touchkey->client->dev, "Skip unhandled keycode(%d)\n",
+ touchkey->keycode_type);
+ return IRQ_HANDLED;
+ }
+
+ if (!touchkey->pressed) {
+ input_report_key(touchkey->input_dev, KEY_PHONE, 0);
+ input_report_key(touchkey->input_dev, KEY_BACK, 0);
+ } else {
+ if (touchkey->keycode_type == TM2_TOUCHKEY_KEY_MENU)
+ input_report_key(touchkey->input_dev,
+ KEY_PHONE, 1);
+ else
+ input_report_key(touchkey->input_dev,
+ KEY_BACK, 1);
+ }
+ input_sync(touchkey->input_dev);
+
+ return IRQ_HANDLED;
+}
+
+static int tm2_touchkey_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct tm2_touchkey_data *touchkey;
+ int ret;
+
+ ret = i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_BYTE |
+ I2C_FUNC_SMBUS_BYTE_DATA);
+ if (!ret) {
+ dev_err(&client->dev, "No I2C functionality found\n");
+ return -ENODEV;
+ }
+
+ touchkey = devm_kzalloc(&client->dev, sizeof(*touchkey), GFP_KERNEL);
+ if (!touchkey)
+ return -ENOMEM;
+
+ touchkey->client = client;
+ i2c_set_clientdata(client, touchkey);
+
+ /* regulators */
+ touchkey->regulators[0].supply = "vcc";
+ touchkey->regulators[1].supply = "vdd";
+ ret = devm_regulator_bulk_get(&client->dev,
+ ARRAY_SIZE(touchkey->regulators),
+ touchkey->regulators);
+ if (ret) {
+ dev_err(&client->dev, "Failed to get regulators\n");
+ return ret;
+ }
+
+ /* power */
+ ret = tm2_touchkey_power_enable(touchkey);
+ if (ret) {
+ dev_err(&client->dev, "Failed to enable power\n");
+ return ret;
+ }
+
+ ret = devm_add_action_or_reset(&client->dev,
+ tm2_touchkey_power_disable, touchkey);
+ if (ret)
+ return ret;
+
+ /* input device */
+ touchkey->input_dev = devm_input_allocate_device(&client->dev);
+ if (!touchkey->input_dev) {
+ dev_err(&client->dev, "Failed to alloc input device\n");
+ return -ENOMEM;
+ }
+ touchkey->input_dev->name = TM2_TOUCHKEY_DEV_NAME;
+ touchkey->input_dev->id.bustype = BUS_I2C;
+
+ set_bit(EV_KEY, touchkey->input_dev->evbit);
+ input_set_capability(touchkey->input_dev, EV_KEY, KEY_PHONE);
+ input_set_capability(touchkey->input_dev, EV_KEY, KEY_BACK);
+
+ input_set_drvdata(touchkey->input_dev, touchkey);
+
+ ret = input_register_device(touchkey->input_dev);
+ if (ret) {
+ dev_err(&client->dev, "Failed to register input device\n");
+ return ret;
+ }
+
+ /* irq */
+ ret = devm_request_threaded_irq(&client->dev,
+ client->irq, NULL,
+ tm2_touchkey_irq_handler,
+ IRQF_ONESHOT, TM2_TOUCHKEY_DEV_NAME,
+ touchkey);
+ if (ret) {
+ dev_err(&client->dev, "Failed to request threaded irq\n");
+ return ret;
+ }
+
+ /* led device */
+ touchkey->led_dev.name = TM2_TOUCHKEY_DEV_NAME;
+ touchkey->led_dev.brightness = LED_FULL;
+ touchkey->led_dev.max_brightness = LED_FULL;
+ touchkey->led_dev.brightness_set = tm2_touchkey_led_brightness_set;
+
+ ret = devm_led_classdev_register(&client->dev, &touchkey->led_dev);
+ if (ret < 0) {
+ dev_err(&client->dev, "Failed to register touchkey led\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int __maybe_unused tm2_touchkey_suspend(struct device *dev)
+{
+ struct tm2_touchkey_data *touchkey = dev_get_drvdata(dev);
+
+ disable_irq(touchkey->client->irq);
+ tm2_touchkey_power_disable(touchkey);
+
+ return 0;
+}
+
+static int __maybe_unused tm2_touchkey_resume(struct device *dev)
+{
+ struct tm2_touchkey_data *touchkey = dev_get_drvdata(dev);
+ int ret;
+
+ enable_irq(touchkey->client->irq);
+ ret = tm2_touchkey_power_enable(touchkey);
+ if (ret)
+ dev_err(dev, "Failed to enable power\n");
+
+ return ret;
+}
+
+static SIMPLE_DEV_PM_OPS(tm2_touchkey_pm_ops, tm2_touchkey_suspend,
+ tm2_touchkey_resume);
+
+static const struct i2c_device_id tm2_touchkey_id_table[] = {
+ {TM2_TOUCHKEY_DEV_NAME, 0},
+ {},
+};
+MODULE_DEVICE_TABLE(i2c, tm2_touchkey_id_table);
+
+static const struct of_device_id tm2_touchkey_of_match[] = {
+ {.compatible = "samsung,tm2-touchkey",},
+ {},
+};
+MODULE_DEVICE_TABLE(of, tm2_touchkey_of_match);
+
+static struct i2c_driver tm2_touchkey_driver = {
+ .driver = {
+ .name = TM2_TOUCHKEY_DEV_NAME,
+ .pm = &tm2_touchkey_pm_ops,
+ .of_match_table = of_match_ptr(tm2_touchkey_of_match),
+ },
+ .probe = tm2_touchkey_probe,
+ .id_table = tm2_touchkey_id_table,
+};
+
+module_i2c_driver(tm2_touchkey_driver);
+
+MODULE_AUTHOR("Beomho Seo <beomho.seo@samsung.com>");
+MODULE_AUTHOR("Jaechul Lee <jcsing.lee@samsung.com>");
+MODULE_DESCRIPTION("Samsung touchkey driver");
+MODULE_LICENSE("GPL v2");
--
2.7.4
^ permalink raw reply related
* [PATCH v3 5/5] arm64: dts: exynos: Add tm2 touchkey node
From: Jaechul Lee @ 2017-01-06 3:59 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483675149-32598-1-git-send-email-jcsing.lee@samsung.com>
Add DT node support for TM2 touchkey device.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
---
arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
index d30b45a..15bdc2e 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
@@ -18,6 +18,19 @@
compatible = "samsung,tm2e", "samsung,exynos5433";
};
+&hsi2c_9 {
+ status = "okay";
+
+ touchkey at 20 {
+ compatible = "samsung,tm2-touchkey";
+ reg = <0x20>;
+ interrupt-parent = <&gpa3>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+ vcc-supply = <&ldo32_reg>;
+ vdd-supply = <&ldo33_reg>;
+ };
+};
+
®ulators {
ldo31_reg: LDO31 {
regulator-name = "TSP_VDD_1.85V_AP";
--
2.7.4
^ permalink raw reply related
* [PATCH v4 2/2] cpufreq: brcmstb-cpufreq: CPUfreq driver for older Broadcom STB SoCs
From: Viresh Kumar @ 2017-01-06 4:14 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161220225530.96699-3-code@mmayer.net>
On 20-12-16, 14:55, Markus Mayer wrote:
> From: Markus Mayer <mmayer@broadcom.com>
>
> This CPUfreq driver provides basic frequency scaling for older Broadcom
> STB SoCs that do not use AVS firmware with DVFS support. There is no
> support for voltage scaling.
>
> Signed-off-by: Markus Mayer <mmayer@broadcom.com>
> ---
> drivers/cpufreq/Kconfig.arm | 12 ++
> drivers/cpufreq/Makefile | 1 +
> drivers/cpufreq/brcmstb-cpufreq.c | 377 ++++++++++++++++++++++++++++++++++++++
> 3 files changed, 390 insertions(+)
> create mode 100644 drivers/cpufreq/brcmstb-cpufreq.c
I am fine with this patch as I have already Acked V3 of it. But please fix the
bindings improvement suggested by Stephen first.
--
viresh
^ permalink raw reply
* [PATCHv2 0/5] Support for Marvell switches with integrated CPUs
From: Chris Packham @ 2017-01-06 4:14 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20170105033641.6212-1-chris.packham@alliedtelesis.co.nz>
The 98DX3236, 98DX3336 and 98DX4251 are a set of switch ASICs with
integrated CPUs. They CPU block is common within these product lines and
(as far as I can tell/have been told) is based on the Armada XP. There
are a few differences due to the fact they have to squeeze the CPU into
the same package as the switch.
Chris Packham (4):
clk: mvebu: support for 98DX3236 SoC
Changes in v2:
- Update devicetree binding documentation for new compatible string
Changes in v3:
- Add 98dx3236 support to mvebu/clk-corediv.c rather than creating a
new driver.
- Document mv98dx3236-corediv-clock binding
arm: mvebu: support for SMP on 98DX3336 SoC
Changes in v2:
- Document new enable-method value
- Correct some references from 98DX4521 to 98DX3236
Changes in v3:
- Simplify mv98dx3236_resume_init by using of_io_request_and_map()
arm: mvebu: Add device tree for 98DX3236 SoCs
Changes in v2:
- Update devicetree binding documentation to reflect that 98DX3336 and
984251 are supersets of 98DX3236.
- disable crypto block
- disable sdio for 98DX3236, enable for 98DX4251
Changes in v3:
- fix typo 4521 -> 4251
- document prestera bindings
- rework corediv-clock binding
- add label to packet processor node
- add new compativle string for DFX server
arm: mvebu: Add device tree for db-dxbc2 and db-xc3-24g4xg boards
Changes in v2/v3:
- none
Kalyan Kinthada (1):
pinctrl: mvebu: pinctrl driver for 98DX3236 SoC
Changes in v2:
- include sdio support for the 98DX4251
Changes in v3:
- None
Documentation/devicetree/bindings/arm/cpus.txt | 1 +
.../bindings/arm/marvell/98dx3236-resume-ctrl.txt | 18 ++
.../devicetree/bindings/arm/marvell/98dx3236.txt | 23 ++
.../bindings/clock/mvebu-corediv-clock.txt | 1 +
.../devicetree/bindings/clock/mvebu-cpu-clock.txt | 1 +
.../devicetree/bindings/net/marvell,prestera.txt | 50 ++++
.../pinctrl/marvell,armada-98dx3236-pinctrl.txt | 46 ++++
arch/arm/boot/dts/armada-xp-98dx3236.dtsi | 254 +++++++++++++++++++++
arch/arm/boot/dts/armada-xp-98dx3336.dtsi | 76 ++++++
arch/arm/boot/dts/armada-xp-98dx4251.dtsi | 90 ++++++++
arch/arm/boot/dts/db-dxbc2.dts | 159 +++++++++++++
arch/arm/boot/dts/db-xc3-24g4xg.dts | 155 +++++++++++++
arch/arm/mach-mvebu/Makefile | 1 +
arch/arm/mach-mvebu/common.h | 1 +
arch/arm/mach-mvebu/platsmp.c | 43 ++++
arch/arm/mach-mvebu/pmsu-98dx3236.c | 52 +++++
drivers/clk/mvebu/armada-xp.c | 42 ++++
drivers/clk/mvebu/clk-corediv.c | 23 ++
drivers/clk/mvebu/clk-cpu.c | 31 ++-
drivers/pinctrl/mvebu/pinctrl-armada-xp.c | 155 +++++++++++++
20 files changed, 1220 insertions(+), 2 deletions(-)
create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt
create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
create mode 100644 Documentation/devicetree/bindings/net/marvell,prestera.txt
create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
create mode 100644 arch/arm/boot/dts/armada-xp-98dx3236.dtsi
create mode 100644 arch/arm/boot/dts/armada-xp-98dx3336.dtsi
create mode 100644 arch/arm/boot/dts/armada-xp-98dx4251.dtsi
create mode 100644 arch/arm/boot/dts/db-dxbc2.dts
create mode 100644 arch/arm/boot/dts/db-xc3-24g4xg.dts
create mode 100644 arch/arm/mach-mvebu/pmsu-98dx3236.c
Interdiff to v2:
diff --git
a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
index 520562a7dc2a..c7b4e3a6b2c6 100644
--- a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
+++ b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
@@ -7,6 +7,7 @@ Required properties:
- compatible : must be "marvell,armada-370-corediv-clock",
"marvell,armada-375-corediv-clock",
"marvell,armada-380-corediv-clock",
+ "marvell,mv98dx3236-corediv-clock",
- reg : must be the register address of Core Divider control register
- #clock-cells : from common clock binding; shall be set to 1
diff --git a/Documentation/devicetree/bindings/net/marvell,prestera.txt
b/Documentation/devicetree/bindings/net/marvell,prestera.txt
new file mode 100644
index 000000000000..5fbab29718e8
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/marvell,prestera.txt
@@ -0,0 +1,50 @@
+Marvell Prestera Switch Chip bindings
+-------------------------------------
+
+Required properties:
+- compatible: one of the following
+ "marvell,prestera-98dx3236",
+ "marvell,prestera-98dx3336",
+ "marvell,prestera-98dx4251",
+- reg: address and length of the register set for the device.
+- interrupts: interrupt for the device
+
+Optional properties:
+- dfx: phandle reference to the "DFX Server" node
+
+Example:
+
+switch {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 MBUS_ID(0x03, 0x00) 0 0x100000>;
+
+ packet-processor at 0 {
+ compatible = "marvell,prestera-98dx3236";
+ reg = <0 0x4000000>;
+ interrupts = <33>, <34>, <35>;
+ dfx = <&dfx>;
+ };
+};
+
+DFX Server bindings
+-------------------
+
+Required properties:
+- compatible: must be "marvell,dfx-server"
+- reg: address and length of the register set for the device.
+
+Example:
+
+dfx-registers {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 MBUS_ID(0x08, 0x00) 0 0x100000>;
+
+ dfx: dfx at 0 {
+ compatible = "marvell,dfx-server";
+ reg = <0 0x100000>;
+ };
+};
diff --git a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
index 61bd3acc5cfe..4b7b2fe3b682 100644
--- a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
+++ b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
@@ -126,12 +126,7 @@
};
corediv-clock at 18740 {
- compatible =
"marvell,mv98dx3236-corediv-clock";
- reg = <0xf8268 0xc>;
- base = <&dfx>;
- #clock-cells = <1>;
- clocks = <&mainpll>;
- clock-output-names = "nand";
+ status = "disabled";
};
xor at 60900 {
@@ -194,6 +189,10 @@
#interrupt-cells = <2>;
interrupts = <87>;
};
+
+ nand: nand at d0000 {
+ clocks = <&dfx_coredivclk 0>;
+ };
};
dfx-registers {
@@ -202,8 +201,16 @@
#size-cells = <1>;
ranges = <0 MBUS_ID(0x08, 0x00) 0 0x100000>;
+ dfx_coredivclk: corediv-clock at f8268 {
+ compatible =
"marvell,mv98dx3236-corediv-clock";
+ reg = <0xf8268 0xc>;
+ #clock-cells = <1>;
+ clocks = <&mainpll>;
+ clock-output-names = "nand";
+ };
+
dfx: dfx at 0 {
- compatible = "simple-bus";
+ compatible = "marvell,dfx-server";
reg = <0 0x100000>;
};
};
@@ -214,7 +221,7 @@
#size-cells = <1>;
ranges = <0 MBUS_ID(0x03, 0x00) 0 0x100000>;
- packet-processor at 0 {
+ pp0: packet-processor at 0 {
compatible =
"marvell,prestera-98dx3236";
reg = <0 0x4000000>;
interrupts = <33>, <34>, <35>;
diff --git a/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
b/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
index 9c9aa565fd82..a9b0f47f8df9 100644
--- a/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
+++ b/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
@@ -68,11 +68,9 @@
reg = <0x20980 0x10>;
};
};
-
- switch {
- packet-processor at 0 {
- compatible =
"marvell,prestera-98dx3336";
- };
- };
};
};
+
+&pp0 {
+ compatible = "marvell,prestera-98dx3336";
+};
diff --git a/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
b/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
index 5f7edc23d5ae..446e6e65ec59 100644
--- a/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
+++ b/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
@@ -68,12 +68,6 @@
reg = <0x20980 0x10>;
};
};
-
- switch {
- packet-processor at 0 {
- compatible =
"marvell,prestera-98dx4521";
- };
- };
};
};
@@ -90,3 +84,7 @@
marvell,function = "sd0";
};
};
+
+&pp0 {
+ compatible = "marvell,prestera-98dx4251";
+};
diff --git a/arch/arm/mach-mvebu/pmsu-98dx3236.c
b/arch/arm/mach-mvebu/pmsu-98dx3236.c
index 87ca42ef40c7..1052674dd439 100644
--- a/arch/arm/mach-mvebu/pmsu-98dx3236.c
+++ b/arch/arm/mach-mvebu/pmsu-98dx3236.c
@@ -31,39 +31,22 @@ void mv98dx3236_resume_set_cpu_boot_addr(int hw_cpu,
void *boot_addr)
static int __init mv98dx3236_resume_init(void)
{
struct device_node *np;
- struct resource res;
- int ret = 0;
+ void __iomem *base;
np = of_find_matching_node(NULL, of_mv98dx3236_resume_table);
if (!np)
return 0;
- pr_info("Initializing 98DX3236 Resume\n");
-
- if (of_address_to_resource(np, 0, &res)) {
- pr_err("unable to get resource\n");
- ret = -ENOENT;
- goto out;
- }
-
- if (!request_mem_region(res.start, resource_size(&res),
- np->full_name)) {
- pr_err("unable to request region\n");
- ret = -EBUSY;
- goto out;
- }
-
- mv98dx3236_resume_base = ioremap(res.start,
resource_size(&res));
- if (!mv98dx3236_resume_base) {
+ base = of_io_request_and_map(np, 0, of_node_full_name(np));
+ if (IS_ERR(base)) {
pr_err("unable to map registers\n");
- release_mem_region(res.start, resource_size(&res));
- ret = -ENOMEM;
- goto out;
+ of_node_put(np);
+ return PTR_ERR(mv98dx3236_resume_base);
}
-out:
+ mv98dx3236_resume_base = base;
of_node_put(np);
- return ret;
+ return 0;
}
early_initcall(mv98dx3236_resume_init);
diff --git a/drivers/clk/mvebu/Makefile b/drivers/clk/mvebu/Makefile
index 6a3681e3d6db..d9ae97fb43c4 100644
--- a/drivers/clk/mvebu/Makefile
+++ b/drivers/clk/mvebu/Makefile
@@ -9,7 +9,7 @@ obj-$(CONFIG_ARMADA_39X_CLK) += armada-39x.o
obj-$(CONFIG_ARMADA_37XX_CLK) += armada-37xx-xtal.o
obj-$(CONFIG_ARMADA_37XX_CLK) += armada-37xx-tbg.o
obj-$(CONFIG_ARMADA_37XX_CLK) += armada-37xx-periph.o
-obj-$(CONFIG_ARMADA_XP_CLK) += armada-xp.o mv98dx3236-corediv.o
+obj-$(CONFIG_ARMADA_XP_CLK) += armada-xp.o
obj-$(CONFIG_ARMADA_AP806_SYSCON) += ap806-system-controller.o
obj-$(CONFIG_ARMADA_CP110_SYSCON) += cp110-system-controller.o
obj-$(CONFIG_DOVE_CLK) += dove.o dove-divider.o
diff --git a/drivers/clk/mvebu/clk-corediv.c
b/drivers/clk/mvebu/clk-corediv.c
index d1e5863d3375..8491979f4096 100644
--- a/drivers/clk/mvebu/clk-corediv.c
+++ b/drivers/clk/mvebu/clk-corediv.c
@@ -71,6 +71,10 @@ static const struct clk_corediv_desc
mvebu_corediv_desc[] = {
{ .mask = 0x3f, .offset = 8, .fieldbit = 1 }, /* NAND clock */
};
+static const struct clk_corediv_desc mv98dx3236_corediv_desc[] = {
+ { .mask = 0x0f, .offset = 6, .fieldbit = 26 }, /* NAND clock */
+};
+
#define to_corediv_clk(p) container_of(p, struct clk_corediv, hw)
static int clk_corediv_is_enabled(struct clk_hw *hwclk)
@@ -232,6 +236,18 @@ static const struct clk_corediv_soc_desc
armada375_corediv_soc = {
.ratio_offset = 0x4,
};
+static const struct clk_corediv_soc_desc mv98dx3236_corediv_soc = {
+ .descs = mv98dx3236_corediv_desc,
+ .ndescs = ARRAY_SIZE(mv98dx3236_corediv_desc),
+ .ops = {
+ .recalc_rate = clk_corediv_recalc_rate,
+ .round_rate = clk_corediv_round_rate,
+ .set_rate = clk_corediv_set_rate,
+ },
+ .ratio_reload = BIT(10),
+ .ratio_offset = 0x8,
+};
+
static void __init
mvebu_corediv_clk_init(struct device_node *node,
const struct clk_corediv_soc_desc *soc_desc)
@@ -313,3 +329,10 @@ static void __init
armada380_corediv_clk_init(struct device_node *node)
}
CLK_OF_DECLARE(armada380_corediv_clk,
"marvell,armada-380-corediv-clock",
armada380_corediv_clk_init);
+
+static void __init mv98dx3236_corediv_clk_init(struct device_node
*node)
+{
+ return mvebu_corediv_clk_init(node, &mv98dx3236_corediv_soc);
+}
+CLK_OF_DECLARE(mv98dx3236_corediv_clk,
"marvell,mv98dx3236-corediv-clock",
+ mv98dx3236_corediv_clk_init);
diff --git a/drivers/clk/mvebu/clk-cpu.c b/drivers/clk/mvebu/clk-cpu.c
index 29f295e7a36b..3b8f0e14fa01 100644
--- a/drivers/clk/mvebu/clk-cpu.c
+++ b/drivers/clk/mvebu/clk-cpu.c
@@ -254,7 +254,7 @@ static void __init of_cpu_clk_setup(struct
device_node *node)
}
CLK_OF_DECLARE(armada_xp_cpu_clock, "marvell,armada-xp-cpu-clock",
- of_cpu_clk_setup);
+ of_cpu_clk_setup);
/* Define the clock and operations for the mv98dx3236 - it cannot
* perform
* any operations.
diff --git a/drivers/clk/mvebu/mv98dx3236-corediv.c
b/drivers/clk/mvebu/mv98dx3236-corediv.c
deleted file mode 100644
index 3060764a8e5d..000000000000
--- a/drivers/clk/mvebu/mv98dx3236-corediv.c
+++ /dev/null
@@ -1,207 +0,0 @@
-/*
- * MV98DX3236 Core divider clock
- *
- * Copyright (C) 2015 Allied Telesis Labs
- *
- * Based on armada-xp-corediv.c
- * Copyright (C) 2015 Marvell
- *
- * John Thompson <john.thompson@alliedtelesis.co.nz>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-#include <linux/kernel.h>
-#include <linux/clk-provider.h>
-#include <linux/of_address.h>
-#include <linux/slab.h>
-#include <linux/delay.h>
-#include "common.h"
-
-#define CORE_CLK_DIV_RATIO_MASK 0xff
-
-#define CLK_DIV_RATIO_NAND_MASK 0x0f
-#define CLK_DIV_RATIO_NAND_OFFSET 6
-#define CLK_DIV_RATIO_NAND_FORCE_RELOAD_BIT 26
-
-#define RATIO_RELOAD_BIT BIT(10)
-#define RATIO_REG_OFFSET 0x08
-
-/*
- * This structure represents one core divider clock for the clock
- * framework, and is dynamically allocated for each core divider clock
- * existing in the current SoC.
- */
-struct clk_corediv {
- struct clk_hw hw;
- void __iomem *reg;
- spinlock_t lock;
-};
-
-static struct clk_onecell_data clk_data;
-
-
-#define to_corediv_clk(p) container_of(p, struct clk_corediv, hw)
-
-static int mv98dx3236_corediv_is_enabled(struct clk_hw *hwclk)
-{
- /* Core divider is always active */
- return 1;
-}
-
-static int mv98dx3236_corediv_enable(struct clk_hw *hwclk)
-{
- /* always succeeds */
- return 0;
-}
-
-static void mv98dx3236_corediv_disable(struct clk_hw *hwclk)
-{
- /* can't be disabled so is left alone */
-}
-
-static unsigned long mv98dx3236_corediv_recalc_rate(struct clk_hw
*hwclk,
- unsigned long parent_rate)
-{
- struct clk_corediv *corediv = to_corediv_clk(hwclk);
- u32 reg, div;
-
- reg = readl(corediv->reg + RATIO_REG_OFFSET);
- div = (reg >> CLK_DIV_RATIO_NAND_OFFSET) &
CLK_DIV_RATIO_NAND_MASK;
- return parent_rate / div;
-}
-
-static long mv98dx3236_corediv_round_rate(struct clk_hw *hwclk,
- unsigned long rate, unsigned long
*parent_rate)
-{
- /* Valid ratio are 1:4, 1:5, 1:6 and 1:8 */
- u32 div;
-
- div = *parent_rate / rate;
- if (div < 4)
- div = 4;
- else if (div > 6)
- div = 8;
-
- return *parent_rate / div;
-}
-
-static int mv98dx3236_corediv_set_rate(struct clk_hw *hwclk, unsigned
long rate,
- unsigned long parent_rate)
-{
- struct clk_corediv *corediv = to_corediv_clk(hwclk);
- unsigned long flags = 0;
- u32 reg, div;
-
- div = parent_rate / rate;
-
- spin_lock_irqsave(&corediv->lock, flags);
-
- /* Write new divider to the divider ratio register */
- reg = readl(corediv->reg + RATIO_REG_OFFSET);
- reg &= ~(CLK_DIV_RATIO_NAND_MASK << CLK_DIV_RATIO_NAND_OFFSET);
- reg |= (div & CLK_DIV_RATIO_NAND_MASK) <<
CLK_DIV_RATIO_NAND_OFFSET;
- writel(reg, corediv->reg + RATIO_REG_OFFSET);
-
- /* Set reload-force for this clock */
- reg = readl(corediv->reg) |
BIT(CLK_DIV_RATIO_NAND_FORCE_RELOAD_BIT);
- writel(reg, corediv->reg);
-
- /* Now trigger the clock update */
- reg = readl(corediv->reg + RATIO_REG_OFFSET) | RATIO_RELOAD_BIT;
- writel(reg, corediv->reg + RATIO_REG_OFFSET);
-
- /*
- * Wait for clocks to settle down, and then clear all the
- * ratios request and the reload request.
- */
- udelay(1000);
- reg &= ~(CORE_CLK_DIV_RATIO_MASK | RATIO_RELOAD_BIT);
- writel(reg, corediv->reg + RATIO_REG_OFFSET);
- udelay(1000);
-
- spin_unlock_irqrestore(&corediv->lock, flags);
-
- return 0;
-}
-
-static const struct clk_ops ops = {
- .enable = mv98dx3236_corediv_enable,
- .disable = mv98dx3236_corediv_disable,
- .is_enabled = mv98dx3236_corediv_is_enabled,
- .recalc_rate = mv98dx3236_corediv_recalc_rate,
- .round_rate = mv98dx3236_corediv_round_rate,
- .set_rate = mv98dx3236_corediv_set_rate,
-};
-
-static void __init mv98dx3236_corediv_clk_init(struct device_node
*node)
-{
- struct clk_init_data init;
- struct clk_corediv *corediv;
- struct clk **clks;
- void __iomem *base;
- const __be32 *off;
- const char *parent_name;
- const char *clk_name;
- int len;
- struct device_node *dfx_node;
-
- dfx_node = of_parse_phandle(node, "base", 0);
- if (WARN_ON(!dfx_node))
- return;
-
- off = of_get_property(node, "reg", &len);
- if (WARN_ON(!off))
- return;
-
- base = of_iomap(dfx_node, 0);
- if (WARN_ON(!base))
- return;
-
- of_node_put(dfx_node);
-
- parent_name = of_clk_get_parent_name(node, 0);
-
- clk_data.clk_num = 1;
-
- /* clks holds the clock array */
- clks = kcalloc(clk_data.clk_num, sizeof(struct clk *),
- GFP_KERNEL);
- if (WARN_ON(!clks))
- goto err_unmap;
- /* corediv holds the clock specific array */
- corediv = kcalloc(clk_data.clk_num, sizeof(struct clk_corediv),
- GFP_KERNEL);
- if (WARN_ON(!corediv))
- goto err_free_clks;
-
- spin_lock_init(&corediv->lock);
-
- of_property_read_string_index(node, "clock-output-names",
- 0, &clk_name);
-
- init.num_parents = 1;
- init.parent_names = &parent_name;
- init.name = clk_name;
- init.ops = &ops;
- init.flags = 0;
-
- corediv[0].reg = (void *)((int)base + be32_to_cpu(*off));
- corediv[0].hw.init = &init;
-
- clks[0] = clk_register(NULL, &corediv[0].hw);
- WARN_ON(IS_ERR(clks[0]));
-
- clk_data.clks = clks;
- of_clk_add_provider(node, of_clk_src_onecell_get, &clk_data);
- return;
-
-err_free_clks:
- kfree(clks);
-err_unmap:
- iounmap(base);
-}
-
-CLK_OF_DECLARE(mv98dx3236_corediv_clk,
"marvell,mv98dx3236-corediv-clock",
- mv98dx3236_corediv_clk_init);
--
2.11.0.24.ge6920cf
^ permalink raw reply related
* [PATCHv3 1/5] clk: mvebu: support for 98DX3236 SoC
From: Chris Packham @ 2017-01-06 4:14 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20170106041517.9589-1-chris.packham@alliedtelesis.co.nz>
The 98DX3236, 98DX3336, 98DX4521 and variants have a different TCLK from
the Armada XP (200MHz vs 250MHz). The CPU core clock is fixed at 800MHz.
The clock gating options are a subset of those on the Armada XP.
The core clock divider is different to the Armada XP also.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
Changes in v2:
- Update devicetree binding documentation for new compatible string
Changes in v3:
- Add 98dx3236 support to mvebu/clk-corediv.c rather than creating a new
driver.
- Document mv98dx3236-corediv-clock binding
.../bindings/clock/mvebu-corediv-clock.txt | 1 +
.../devicetree/bindings/clock/mvebu-cpu-clock.txt | 1 +
drivers/clk/mvebu/armada-xp.c | 42 ++++++++++++++++++++++
drivers/clk/mvebu/clk-corediv.c | 23 ++++++++++++
drivers/clk/mvebu/clk-cpu.c | 31 ++++++++++++++--
5 files changed, 96 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
index 520562a7dc2a..c7b4e3a6b2c6 100644
--- a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
+++ b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
@@ -7,6 +7,7 @@ Required properties:
- compatible : must be "marvell,armada-370-corediv-clock",
"marvell,armada-375-corediv-clock",
"marvell,armada-380-corediv-clock",
+ "marvell,mv98dx3236-corediv-clock",
- reg : must be the register address of Core Divider control register
- #clock-cells : from common clock binding; shall be set to 1
diff --git a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
index 99c214660bdc..7f28506eaee7 100644
--- a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
+++ b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
@@ -3,6 +3,7 @@ Device Tree Clock bindings for cpu clock of Marvell EBU platforms
Required properties:
- compatible : shall be one of the following:
"marvell,armada-xp-cpu-clock" - cpu clocks for Armada XP
+ "marvell,mv98dx3236-cpu-clock" - cpu clocks for 98DX3236 SoC
- reg : Address and length of the clock complex register set, followed
by address and length of the PMU DFS registers
- #clock-cells : should be set to 1.
diff --git a/drivers/clk/mvebu/armada-xp.c b/drivers/clk/mvebu/armada-xp.c
index b3094315a3c0..0413bf8284e0 100644
--- a/drivers/clk/mvebu/armada-xp.c
+++ b/drivers/clk/mvebu/armada-xp.c
@@ -52,6 +52,12 @@ static u32 __init axp_get_tclk_freq(void __iomem *sar)
return 250000000;
}
+/* MV98DX3236 TCLK frequency is fixed to 200MHz */
+static u32 __init mv98dx3236_get_tclk_freq(void __iomem *sar)
+{
+ return 200000000;
+}
+
static const u32 axp_cpu_freqs[] __initconst = {
1000000000,
1066000000,
@@ -89,6 +95,12 @@ static u32 __init axp_get_cpu_freq(void __iomem *sar)
return cpu_freq;
}
+/* MV98DX3236 CLK frequency is fixed to 800MHz */
+static u32 __init mv98dx3236_get_cpu_freq(void __iomem *sar)
+{
+ return 800000000;
+}
+
static const int axp_nbclk_ratios[32][2] __initconst = {
{0, 1}, {1, 2}, {2, 2}, {2, 2},
{1, 2}, {1, 2}, {1, 1}, {2, 3},
@@ -158,6 +170,14 @@ static const struct coreclk_soc_desc axp_coreclks = {
.num_ratios = ARRAY_SIZE(axp_coreclk_ratios),
};
+static const struct coreclk_soc_desc mv98dx3236_coreclks = {
+ .get_tclk_freq = mv98dx3236_get_tclk_freq,
+ .get_cpu_freq = mv98dx3236_get_cpu_freq,
+ .get_clk_ratio = NULL,
+ .ratios = NULL,
+ .num_ratios = 0,
+};
+
/*
* Clock Gating Control
*/
@@ -195,6 +215,15 @@ static const struct clk_gating_soc_desc axp_gating_desc[] __initconst = {
{ }
};
+static const struct clk_gating_soc_desc mv98dx3236_gating_desc[] __initconst = {
+ { "ge1", NULL, 3, 0 },
+ { "ge0", NULL, 4, 0 },
+ { "pex00", NULL, 5, 0 },
+ { "sdio", NULL, 17, 0 },
+ { "xor0", NULL, 22, 0 },
+ { }
+};
+
static void __init axp_clk_init(struct device_node *np)
{
struct device_node *cgnp =
@@ -206,3 +235,16 @@ static void __init axp_clk_init(struct device_node *np)
mvebu_clk_gating_setup(cgnp, axp_gating_desc);
}
CLK_OF_DECLARE(axp_clk, "marvell,armada-xp-core-clock", axp_clk_init);
+
+static void __init mv98dx3236_clk_init(struct device_node *np)
+{
+ struct device_node *cgnp =
+ of_find_compatible_node(NULL, NULL, "marvell,armada-xp-gating-clock");
+
+ mvebu_coreclk_setup(np, &mv98dx3236_coreclks);
+
+ if (cgnp)
+ mvebu_clk_gating_setup(cgnp, mv98dx3236_gating_desc);
+}
+CLK_OF_DECLARE(mv98dx3236_clk, "marvell,mv98dx3236-core-clock",
+ mv98dx3236_clk_init);
diff --git a/drivers/clk/mvebu/clk-corediv.c b/drivers/clk/mvebu/clk-corediv.c
index d1e5863d3375..8491979f4096 100644
--- a/drivers/clk/mvebu/clk-corediv.c
+++ b/drivers/clk/mvebu/clk-corediv.c
@@ -71,6 +71,10 @@ static const struct clk_corediv_desc mvebu_corediv_desc[] = {
{ .mask = 0x3f, .offset = 8, .fieldbit = 1 }, /* NAND clock */
};
+static const struct clk_corediv_desc mv98dx3236_corediv_desc[] = {
+ { .mask = 0x0f, .offset = 6, .fieldbit = 26 }, /* NAND clock */
+};
+
#define to_corediv_clk(p) container_of(p, struct clk_corediv, hw)
static int clk_corediv_is_enabled(struct clk_hw *hwclk)
@@ -232,6 +236,18 @@ static const struct clk_corediv_soc_desc armada375_corediv_soc = {
.ratio_offset = 0x4,
};
+static const struct clk_corediv_soc_desc mv98dx3236_corediv_soc = {
+ .descs = mv98dx3236_corediv_desc,
+ .ndescs = ARRAY_SIZE(mv98dx3236_corediv_desc),
+ .ops = {
+ .recalc_rate = clk_corediv_recalc_rate,
+ .round_rate = clk_corediv_round_rate,
+ .set_rate = clk_corediv_set_rate,
+ },
+ .ratio_reload = BIT(10),
+ .ratio_offset = 0x8,
+};
+
static void __init
mvebu_corediv_clk_init(struct device_node *node,
const struct clk_corediv_soc_desc *soc_desc)
@@ -313,3 +329,10 @@ static void __init armada380_corediv_clk_init(struct device_node *node)
}
CLK_OF_DECLARE(armada380_corediv_clk, "marvell,armada-380-corediv-clock",
armada380_corediv_clk_init);
+
+static void __init mv98dx3236_corediv_clk_init(struct device_node *node)
+{
+ return mvebu_corediv_clk_init(node, &mv98dx3236_corediv_soc);
+}
+CLK_OF_DECLARE(mv98dx3236_corediv_clk, "marvell,mv98dx3236-corediv-clock",
+ mv98dx3236_corediv_clk_init);
diff --git a/drivers/clk/mvebu/clk-cpu.c b/drivers/clk/mvebu/clk-cpu.c
index 5837eb8a212f..3b8f0e14fa01 100644
--- a/drivers/clk/mvebu/clk-cpu.c
+++ b/drivers/clk/mvebu/clk-cpu.c
@@ -165,7 +165,9 @@ static const struct clk_ops cpu_ops = {
.set_rate = clk_cpu_set_rate,
};
-static void __init of_cpu_clk_setup(struct device_node *node)
+/* Add parameter to allow this to support different clock operations. */
+static void __init _of_cpu_clk_setup(struct device_node *node,
+ const struct clk_ops *cpu_clk_ops)
{
struct cpu_clk *cpuclk;
void __iomem *clock_complex_base = of_iomap(node, 0);
@@ -218,7 +220,7 @@ static void __init of_cpu_clk_setup(struct device_node *node)
cpuclk[cpu].hw.init = &init;
init.name = cpuclk[cpu].clk_name;
- init.ops = &cpu_ops;
+ init.ops = cpu_clk_ops;
init.flags = 0;
init.parent_names = &cpuclk[cpu].parent_name;
init.num_parents = 1;
@@ -243,5 +245,30 @@ static void __init of_cpu_clk_setup(struct device_node *node)
iounmap(clock_complex_base);
}
+/* Use this function to call the generic setup with the correct
+ * clock operation
+ */
+static void __init of_cpu_clk_setup(struct device_node *node)
+{
+ _of_cpu_clk_setup(node, &cpu_ops);
+}
+
CLK_OF_DECLARE(armada_xp_cpu_clock, "marvell,armada-xp-cpu-clock",
of_cpu_clk_setup);
+
+/* Define the clock and operations for the mv98dx3236 - it cannot perform
+ * any operations.
+ */
+static const struct clk_ops mv98dx3236_cpu_ops = {
+ .recalc_rate = NULL,
+ .round_rate = NULL,
+ .set_rate = NULL,
+};
+
+static void __init of_mv98dx3236_cpu_clk_setup(struct device_node *node)
+{
+ _of_cpu_clk_setup(node, &mv98dx3236_cpu_ops);
+}
+
+CLK_OF_DECLARE(mv98dx3236_cpu_clock, "marvell,mv98dx3236-cpu-clock",
+ of_mv98dx3236_cpu_clk_setup);
--
2.11.0.24.ge6920cf
^ permalink raw reply related
* [PATCHv3 2/5] arm: mvebu: support for SMP on 98DX3336 SoC
From: Chris Packham @ 2017-01-06 4:14 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20170106041517.9589-1-chris.packham@alliedtelesis.co.nz>
Compared to the armada-xp the 98DX3336 uses different registers to set
the boot address for the secondary CPU so a new enable-method is needed.
This will only work if the machine definition doesn't define an overall
smp_ops because there is not currently a way of overriding this from the
device tree if it is set in the machine definition.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
Changes in v2:
- Document new enable-method value
- Correct some references from 98DX4521 to 98DX3236
Changes in v3:
- Simplify mv98dx3236_resume_init by using of_io_request_and_map()
Documentation/devicetree/bindings/arm/cpus.txt | 1 +
.../bindings/arm/marvell/98dx3236-resume-ctrl.txt | 18 ++++++++
arch/arm/mach-mvebu/Makefile | 1 +
arch/arm/mach-mvebu/common.h | 1 +
arch/arm/mach-mvebu/platsmp.c | 43 ++++++++++++++++++
arch/arm/mach-mvebu/pmsu-98dx3236.c | 52 ++++++++++++++++++++++
6 files changed, 116 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt
create mode 100644 arch/arm/mach-mvebu/pmsu-98dx3236.c
diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt
index a1bcfeed5f24..3c2fd72d0bf9 100644
--- a/Documentation/devicetree/bindings/arm/cpus.txt
+++ b/Documentation/devicetree/bindings/arm/cpus.txt
@@ -202,6 +202,7 @@ nodes to be present and contain the properties described below.
"marvell,armada-380-smp"
"marvell,armada-390-smp"
"marvell,armada-xp-smp"
+ "marvell,98dx3236-smp"
"mediatek,mt6589-smp"
"mediatek,mt81xx-tz-smp"
"qcom,gcc-msm8660"
diff --git a/Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt b/Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt
new file mode 100644
index 000000000000..8082ba872edd
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt
@@ -0,0 +1,18 @@
+Resume Control
+--------------
+Available on Marvell SOCs: 98DX3336 and 98DX4251
+
+Required properties:
+
+- compatible: must be "marvell,98dx3336-resume-ctrl"
+
+- reg: Should contain resume control registers location and length
+
+Example:
+
+resume at 20980 {
+ compatible = "marvell,98dx3336-resume-ctrl";
+ reg = <0x20980 0x10>;
+};
+
+
diff --git a/arch/arm/mach-mvebu/Makefile b/arch/arm/mach-mvebu/Makefile
index 6c6497e80a7b..2a2dd8324fb8 100644
--- a/arch/arm/mach-mvebu/Makefile
+++ b/arch/arm/mach-mvebu/Makefile
@@ -7,6 +7,7 @@ obj-$(CONFIG_MACH_MVEBU_ANY) += system-controller.o mvebu-soc-id.o
ifeq ($(CONFIG_MACH_MVEBU_V7),y)
obj-y += cpu-reset.o board-v7.o coherency.o coherency_ll.o pmsu.o pmsu_ll.o
+obj-y += pmsu-98dx3236.o
obj-$(CONFIG_PM) += pm.o pm-board.o
obj-$(CONFIG_SMP) += platsmp.o headsmp.o platsmp-a9.o headsmp-a9.o
diff --git a/arch/arm/mach-mvebu/common.h b/arch/arm/mach-mvebu/common.h
index 6b775492cfad..099dabf23461 100644
--- a/arch/arm/mach-mvebu/common.h
+++ b/arch/arm/mach-mvebu/common.h
@@ -27,4 +27,5 @@ void __iomem *mvebu_get_scu_base(void);
int mvebu_pm_suspend_init(void (*board_pm_enter)(void __iomem *sdram_reg,
u32 srcmd));
+void mv98dx3236_resume_set_cpu_boot_addr(int hw_cpu, void *boot_addr);
#endif
diff --git a/arch/arm/mach-mvebu/platsmp.c b/arch/arm/mach-mvebu/platsmp.c
index 46c742d3bd41..3c9ab9a008ad 100644
--- a/arch/arm/mach-mvebu/platsmp.c
+++ b/arch/arm/mach-mvebu/platsmp.c
@@ -182,5 +182,48 @@ const struct smp_operations armada_xp_smp_ops __initconst = {
#endif
};
+static int mv98dx3236_boot_secondary(unsigned int cpu, struct task_struct *idle)
+{
+ int ret, hw_cpu;
+
+ pr_info("Booting CPU %d\n", cpu);
+
+ hw_cpu = cpu_logical_map(cpu);
+ set_secondary_cpu_clock(hw_cpu);
+ mv98dx3236_resume_set_cpu_boot_addr(hw_cpu,
+ armada_xp_secondary_startup);
+
+ /*
+ * This is needed to wake up CPUs in the offline state after
+ * using CPU hotplug.
+ */
+ arch_send_wakeup_ipi_mask(cpumask_of(cpu));
+
+ /*
+ * This is needed to take secondary CPUs out of reset on the
+ * initial boot.
+ */
+ ret = mvebu_cpu_reset_deassert(hw_cpu);
+ if (ret) {
+ pr_warn("unable to boot CPU: %d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+struct smp_operations mv98dx3236_smp_ops __initdata = {
+ .smp_init_cpus = armada_xp_smp_init_cpus,
+ .smp_prepare_cpus = armada_xp_smp_prepare_cpus,
+ .smp_boot_secondary = mv98dx3236_boot_secondary,
+ .smp_secondary_init = armada_xp_secondary_init,
+#ifdef CONFIG_HOTPLUG_CPU
+ .cpu_die = armada_xp_cpu_die,
+ .cpu_kill = armada_xp_cpu_kill,
+#endif
+};
+
CPU_METHOD_OF_DECLARE(armada_xp_smp, "marvell,armada-xp-smp",
&armada_xp_smp_ops);
+CPU_METHOD_OF_DECLARE(mv98dx3236_smp, "marvell,98dx3236-smp",
+ &mv98dx3236_smp_ops);
diff --git a/arch/arm/mach-mvebu/pmsu-98dx3236.c b/arch/arm/mach-mvebu/pmsu-98dx3236.c
new file mode 100644
index 000000000000..1052674dd439
--- /dev/null
+++ b/arch/arm/mach-mvebu/pmsu-98dx3236.c
@@ -0,0 +1,52 @@
+/**
+ * CPU resume support for 98DX3236 internal CPU (a.k.a. MSYS).
+ */
+
+#define pr_fmt(fmt) "mv98dx3236-resume: " fmt
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/of_address.h>
+#include <linux/io.h>
+#include "common.h"
+
+static void __iomem *mv98dx3236_resume_base;
+#define MV98DX3236_CPU_RESUME_CTRL_OFFSET 0x08
+#define MV98DX3236_CPU_RESUME_ADDR_OFFSET 0x04
+
+static const struct of_device_id of_mv98dx3236_resume_table[] = {
+ {.compatible = "marvell,98dx3336-resume-ctrl",},
+ { /* end of list */ },
+};
+
+void mv98dx3236_resume_set_cpu_boot_addr(int hw_cpu, void *boot_addr)
+{
+ WARN_ON(hw_cpu != 1);
+
+ writel(0, mv98dx3236_resume_base + MV98DX3236_CPU_RESUME_CTRL_OFFSET);
+ writel(virt_to_phys(boot_addr), mv98dx3236_resume_base +
+ MV98DX3236_CPU_RESUME_ADDR_OFFSET);
+}
+
+static int __init mv98dx3236_resume_init(void)
+{
+ struct device_node *np;
+ void __iomem *base;
+
+ np = of_find_matching_node(NULL, of_mv98dx3236_resume_table);
+ if (!np)
+ return 0;
+
+ base = of_io_request_and_map(np, 0, of_node_full_name(np));
+ if (IS_ERR(base)) {
+ pr_err("unable to map registers\n");
+ of_node_put(np);
+ return PTR_ERR(mv98dx3236_resume_base);
+ }
+
+ mv98dx3236_resume_base = base;
+ of_node_put(np);
+ return 0;
+}
+
+early_initcall(mv98dx3236_resume_init);
--
2.11.0.24.ge6920cf
^ permalink raw reply related
* [PATCHv3 3/5] pinctrl: mvebu: pinctrl driver for 98DX3236 SoC
From: Chris Packham @ 2017-01-06 4:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20170106041517.9589-1-chris.packham@alliedtelesis.co.nz>
From: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
This pinctrl driver supports the 98DX3236, 98DX3336 and 98DX4251 SoCs
from Marvell.
Signed-off-by: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
Changes in v2:
- include sdio support for the 98DX4251
Changes in v3:
- None
.../pinctrl/marvell,armada-98dx3236-pinctrl.txt | 46 ++++++
drivers/pinctrl/mvebu/pinctrl-armada-xp.c | 155 +++++++++++++++++++++
2 files changed, 201 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
new file mode 100644
index 000000000000..d4e6ecdfc853
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
@@ -0,0 +1,46 @@
+* Marvell 98dx3236 pinctrl driver for mpp
+
+Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
+part and usage
+
+Required properties:
+- compatible: "marvell,98dx3236-pinctrl" or "marvell,98dx4251-pinctrl"
+- reg: register specifier of MPP registers
+
+This driver supports all 98dx3236, 98dx3336 and 98dx4251 variants
+
+name pins functions
+================================================================================
+mpp0 0 gpio, spi0(mosi), dev(ad8)
+mpp1 1 gpio, spi0(miso), dev(ad9)
+mpp2 2 gpio, spi0(sck), dev(ad10)
+mpp3 3 gpio, spi0(cs0), dev(ad11)
+mpp4 4 gpio, spi0(cs1), smi(mdc), dev(cs0)
+mpp5 5 gpio, pex(rsto), sd0(cmd), dev(bootcs)
+mpp6 6 gpio, sd0(clk), dev(a2)
+mpp7 7 gpio, sd0(d0), dev(ale0)
+mpp8 8 gpio, sd0(d1), dev(ale1)
+mpp9 9 gpio, sd0(d2), dev(ready0)
+mpp10 10 gpio, sd0(d3), dev(ad12)
+mpp11 11 gpio, uart1(rxd), uart0(cts), dev(ad13)
+mpp12 12 gpio, uart1(txd), uart0(rts), dev(ad14)
+mpp13 13 gpio, intr(out), dev(ad15)
+mpp14 14 gpio, i2c0(sck)
+mpp15 15 gpio, i2c0(sda)
+mpp16 16 gpio, dev(oe)
+mpp17 17 gpio, dev(clk)
+mpp18 18 gpio, uart1(txd)
+mpp19 19 gpio, uart1(rxd), dev(rb)
+mpp20 20 gpio, dev(we)
+mpp21 21 gpio, dev(ad0)
+mpp22 22 gpio, dev(ad1)
+mpp23 23 gpio, dev(ad2)
+mpp24 24 gpio, dev(ad3)
+mpp25 25 gpio, dev(ad4)
+mpp26 26 gpio, dev(ad5)
+mpp27 27 gpio, dev(ad6)
+mpp28 28 gpio, dev(ad7)
+mpp29 29 gpio, dev(a0)
+mpp30 30 gpio, dev(a1)
+mpp31 31 gpio, slv_smi(mdc), smi(mdc), dev(we1)
+mpp32 32 gpio, slv_smi(mdio), smi(mdio), dev(cs1)
diff --git a/drivers/pinctrl/mvebu/pinctrl-armada-xp.c b/drivers/pinctrl/mvebu/pinctrl-armada-xp.c
index e4ea71a9d985..554eeae8cd21 100644
--- a/drivers/pinctrl/mvebu/pinctrl-armada-xp.c
+++ b/drivers/pinctrl/mvebu/pinctrl-armada-xp.c
@@ -49,6 +49,10 @@ enum armada_xp_variant {
V_MV78460 = BIT(2),
V_MV78230_PLUS = (V_MV78230 | V_MV78260 | V_MV78460),
V_MV78260_PLUS = (V_MV78260 | V_MV78460),
+ V_98DX3236 = BIT(3),
+ V_98DX3336 = BIT(4),
+ V_98DX4251 = BIT(5),
+ V_98DX3236_PLUS = (V_98DX3236 | V_98DX3336 | V_98DX4251),
};
static struct mvebu_mpp_mode armada_xp_mpp_modes[] = {
@@ -360,6 +364,130 @@ static struct mvebu_mpp_mode armada_xp_mpp_modes[] = {
MPP_VAR_FUNCTION(0x1, "dev", "ad31", V_MV78260_PLUS)),
};
+static struct mvebu_mpp_mode mv98dx3236_mpp_modes[] = {
+ MPP_MODE(0,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "spi0", "mosi", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad8", V_98DX3236_PLUS)),
+ MPP_MODE(1,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "spi0", "miso", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad9", V_98DX3236_PLUS)),
+ MPP_MODE(2,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "spi0", "csk", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad10", V_98DX3236_PLUS)),
+ MPP_MODE(3,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "spi0", "cs0", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad11", V_98DX3236_PLUS)),
+ MPP_MODE(4,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "spi0", "cs1", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "smi", "mdc", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "cs0", V_98DX3236_PLUS)),
+ MPP_MODE(5,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "pex", "rsto", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "cmd", V_98DX4251),
+ MPP_VAR_FUNCTION(0x4, "dev", "bootcs0", V_98DX3236_PLUS)),
+ MPP_MODE(6,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "clk", V_98DX4251),
+ MPP_VAR_FUNCTION(0x4, "dev", "a2", V_98DX3236_PLUS)),
+ MPP_MODE(7,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "d0", V_98DX4251),
+ MPP_VAR_FUNCTION(0x4, "dev", "ale0", V_98DX3236_PLUS)),
+ MPP_MODE(8,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "d1", V_98DX4251),
+ MPP_VAR_FUNCTION(0x4, "dev", "ale1", V_98DX3236_PLUS)),
+ MPP_MODE(9,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "d2", V_98DX4251),
+ MPP_VAR_FUNCTION(0x4, "dev", "ready0", V_98DX3236_PLUS)),
+ MPP_MODE(10,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "d3", V_98DX4251),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad12", V_98DX3236_PLUS)),
+ MPP_MODE(11,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "uart1", "rxd", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "uart0", "cts", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad13", V_98DX3236_PLUS)),
+ MPP_MODE(12,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "uart1", "txd", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "uart0", "rts", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad14", V_98DX3236_PLUS)),
+ MPP_MODE(13,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "intr", "out", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad15", V_98DX3236_PLUS)),
+ MPP_MODE(14,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "i2c0", "sck", V_98DX3236_PLUS)),
+ MPP_MODE(15,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "i2c0", "sda", V_98DX3236_PLUS)),
+ MPP_MODE(16,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "oe", V_98DX3236_PLUS)),
+ MPP_MODE(17,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "clkout", V_98DX3236_PLUS)),
+ MPP_MODE(18,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "uart1", "txd", V_98DX3236_PLUS)),
+ MPP_MODE(19,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "uart1", "rxd", V_98DX3236_PLUS)),
+ MPP_MODE(20,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "we0", V_98DX3236_PLUS)),
+ MPP_MODE(21,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad0", V_98DX3236_PLUS)),
+ MPP_MODE(22,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad1", V_98DX3236_PLUS)),
+ MPP_MODE(23,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad2", V_98DX3236_PLUS)),
+ MPP_MODE(24,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad3", V_98DX3236_PLUS)),
+ MPP_MODE(25,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad4", V_98DX3236_PLUS)),
+ MPP_MODE(26,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad5", V_98DX3236_PLUS)),
+ MPP_MODE(27,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad6", V_98DX3236_PLUS)),
+ MPP_MODE(28,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad7", V_98DX3236_PLUS)),
+ MPP_MODE(29,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "a0", V_98DX3236_PLUS)),
+ MPP_MODE(30,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "a1", V_98DX3236_PLUS)),
+ MPP_MODE(31,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "slv_smi", "mdc", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "smi", "mdc", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "we1", V_98DX3236_PLUS)),
+ MPP_MODE(32,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "slv_smi", "mdio", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "smi", "mdio", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "cs1", V_98DX3236_PLUS)),
+};
+
static struct mvebu_pinctrl_soc_info armada_xp_pinctrl_info;
static const struct of_device_id armada_xp_pinctrl_of_match[] = {
@@ -375,6 +503,14 @@ static const struct of_device_id armada_xp_pinctrl_of_match[] = {
.compatible = "marvell,mv78460-pinctrl",
.data = (void *) V_MV78460,
},
+ {
+ .compatible = "marvell,98dx3236-pinctrl",
+ .data = (void *) V_98DX3236,
+ },
+ {
+ .compatible = "marvell,98dx4251-pinctrl",
+ .data = (void *) V_98DX4251,
+ },
{ },
};
@@ -407,6 +543,14 @@ static struct pinctrl_gpio_range mv78460_mpp_gpio_ranges[] = {
MPP_GPIO_RANGE(2, 64, 64, 3),
};
+static struct mvebu_mpp_ctrl mv98dx3236_mpp_controls[] = {
+ MPP_FUNC_CTRL(0, 32, NULL, armada_xp_mpp_ctrl),
+};
+
+static struct pinctrl_gpio_range mv98dx3236_mpp_gpio_ranges[] = {
+ MPP_GPIO_RANGE(0, 0, 0, 32),
+};
+
static int armada_xp_pinctrl_suspend(struct platform_device *pdev,
pm_message_t state)
{
@@ -488,6 +632,17 @@ static int armada_xp_pinctrl_probe(struct platform_device *pdev)
soc->gpioranges = mv78460_mpp_gpio_ranges;
soc->ngpioranges = ARRAY_SIZE(mv78460_mpp_gpio_ranges);
break;
+ case V_98DX3236:
+ case V_98DX3336:
+ case V_98DX4251:
+ /* fall-through */
+ soc->controls = mv98dx3236_mpp_controls;
+ soc->ncontrols = ARRAY_SIZE(mv98dx3236_mpp_controls);
+ soc->modes = mv98dx3236_mpp_modes;
+ soc->nmodes = mv98dx3236_mpp_controls[0].npins;
+ soc->gpioranges = mv98dx3236_mpp_gpio_ranges;
+ soc->ngpioranges = ARRAY_SIZE(mv98dx3236_mpp_gpio_ranges);
+ break;
}
nregs = DIV_ROUND_UP(soc->nmodes, MVEBU_MPPS_PER_REG);
--
2.11.0.24.ge6920cf
^ permalink raw reply related
* [PATCHv3 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs
From: Chris Packham @ 2017-01-06 4:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20170106041517.9589-1-chris.packham@alliedtelesis.co.nz>
The Marvell 98DX3236, 98DX3336, 98DX4521 and variants are switch ASICs
with integrated CPUs. They are similar to the Armada XP SoCs but have
different I/O interfaces.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
Changes in v2:
- Update devicetree binding documentation to reflect that 98DX3336 and
984251 are supersets of 98DX3236.
- disable crypto block
- disable sdio for 98DX3236, enable for 98DX4251
Changes in v3:
- fix typo 4521 -> 4251
- document prestera bindings
- rework corediv-clock binding
- add label to packet processor node
- add new compativle string for DFX server
.../devicetree/bindings/arm/marvell/98dx3236.txt | 23 ++
.../devicetree/bindings/net/marvell,prestera.txt | 50 ++++
arch/arm/boot/dts/armada-xp-98dx3236.dtsi | 254 +++++++++++++++++++++
arch/arm/boot/dts/armada-xp-98dx3336.dtsi | 76 ++++++
arch/arm/boot/dts/armada-xp-98dx4251.dtsi | 90 ++++++++
5 files changed, 493 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
create mode 100644 Documentation/devicetree/bindings/net/marvell,prestera.txt
create mode 100644 arch/arm/boot/dts/armada-xp-98dx3236.dtsi
create mode 100644 arch/arm/boot/dts/armada-xp-98dx3336.dtsi
create mode 100644 arch/arm/boot/dts/armada-xp-98dx4251.dtsi
diff --git a/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt b/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
new file mode 100644
index 000000000000..64e8c73fc5ab
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
@@ -0,0 +1,23 @@
+Marvell 98DX3236, 98DX3336 and 98DX4251 Platforms Device Tree Bindings
+----------------------------------------------------------------------
+
+Boards with a SoC of the Marvell 98DX3236, 98DX3336 and 98DX4251 families
+shall have the following property:
+
+Required root node property:
+
+compatible: must contain "marvell,armadaxp-98dx3236"
+
+In addition, boards using the Marvell 98DX3336 SoC shall have the
+following property:
+
+Required root node property:
+
+compatible: must contain "marvell,armadaxp-98dx3336"
+
+In addition, boards using the Marvell 98DX4251 SoC shall have the
+following property:
+
+Required root node property:
+
+compatible: must contain "marvell,armadaxp-98dx4251"
diff --git a/Documentation/devicetree/bindings/net/marvell,prestera.txt b/Documentation/devicetree/bindings/net/marvell,prestera.txt
new file mode 100644
index 000000000000..5fbab29718e8
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/marvell,prestera.txt
@@ -0,0 +1,50 @@
+Marvell Prestera Switch Chip bindings
+-------------------------------------
+
+Required properties:
+- compatible: one of the following
+ "marvell,prestera-98dx3236",
+ "marvell,prestera-98dx3336",
+ "marvell,prestera-98dx4251",
+- reg: address and length of the register set for the device.
+- interrupts: interrupt for the device
+
+Optional properties:
+- dfx: phandle reference to the "DFX Server" node
+
+Example:
+
+switch {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 MBUS_ID(0x03, 0x00) 0 0x100000>;
+
+ packet-processor at 0 {
+ compatible = "marvell,prestera-98dx3236";
+ reg = <0 0x4000000>;
+ interrupts = <33>, <34>, <35>;
+ dfx = <&dfx>;
+ };
+};
+
+DFX Server bindings
+-------------------
+
+Required properties:
+- compatible: must be "marvell,dfx-server"
+- reg: address and length of the register set for the device.
+
+Example:
+
+dfx-registers {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 MBUS_ID(0x08, 0x00) 0 0x100000>;
+
+ dfx: dfx at 0 {
+ compatible = "marvell,dfx-server";
+ reg = <0 0x100000>;
+ };
+};
diff --git a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
new file mode 100644
index 000000000000..4b7b2fe3b682
--- /dev/null
+++ b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
@@ -0,0 +1,254 @@
+/*
+ * Device Tree Include file for Marvell 98dx3236 family SoC
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Contains definitions specific to the 98dx3236 SoC that are not
+ * common to all Armada XP SoCs.
+ */
+
+#include "armada-xp.dtsi"
+
+/ {
+ model = "Marvell 98DX3236 SoC";
+ compatible = "marvell,armadaxp-98dx3236", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ aliases {
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ gpio2 = &gpio2;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ enable-method = "marvell,98dx3236-smp";
+
+ cpu at 0 {
+ device_type = "cpu";
+ compatible = "marvell,sheeva-v7";
+ reg = <0>;
+ clocks = <&cpuclk 0>;
+ clock-latency = <1000000>;
+ };
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
+ MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
+ MBUS_ID(0x03, 0x00) 0 0 0xa8000000 0x4000000
+ MBUS_ID(0x08, 0x00) 0 0 0xac000000 0x100000>;
+
+ /*
+ * 98DX3236 has 1 x1 PCIe unit Gen2.0: One unit can be
+ */
+ pcie-controller {
+ compatible = "marvell,armada-xp-pcie";
+ status = "disabled";
+ device_type = "pci";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ msi-parent = <&mpic>;
+ bus-range = <0x00 0xff>;
+
+ ranges =
+ <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 /* Port 0.0 registers */
+ 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
+ 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */
+ 0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */>;
+
+ pcie at 1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+ 0x81000000 0 0 0x81000000 0x1 0 1 0>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 58>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 5>;
+ status = "disabled";
+ };
+ };
+
+ internal-regs {
+ coreclk: mvebu-sar at 18230 {
+ compatible = "marvell,mv98dx3236-core-clock";
+ };
+
+ cpuclk: clock-complex at 18700 {
+ compatible = "marvell,mv98dx3236-cpu-clock";
+ };
+
+ corediv-clock at 18740 {
+ status = "disabled";
+ };
+
+ xor at 60900 {
+ status = "disabled";
+ };
+
+ crypto at 90000 {
+ status = "disabled";
+ };
+
+ xor at f0900 {
+ status = "disabled";
+ };
+
+ xor at f0800 {
+ compatible = "marvell,orion-xor";
+ reg = <0xf0800 0x100
+ 0xf0a00 0x100>;
+ clocks = <&gateclk 22>;
+ status = "okay";
+
+ xor10 {
+ interrupts = <51>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ xor11 {
+ interrupts = <52>;
+ dmacap,memcpy;
+ dmacap,xor;
+ dmacap,memset;
+ };
+ };
+
+ gpio0: gpio at 18100 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18100 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <82>, <83>, <84>, <85>;
+ };
+
+ /* does not exist */
+ gpio1: gpio at 18140 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18140 0x40>;
+ status = "disabled";
+ };
+
+ gpio2: gpio at 18180 { /* rework some properties */
+ compatible = "marvell,orion-gpio";
+ reg = <0x18180 0x40>;
+ ngpios = <1>; /* only gpio #32 */
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <87>;
+ };
+
+ nand: nand at d0000 {
+ clocks = <&dfx_coredivclk 0>;
+ };
+ };
+
+ dfx-registers {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 MBUS_ID(0x08, 0x00) 0 0x100000>;
+
+ dfx_coredivclk: corediv-clock at f8268 {
+ compatible = "marvell,mv98dx3236-corediv-clock";
+ reg = <0xf8268 0xc>;
+ #clock-cells = <1>;
+ clocks = <&mainpll>;
+ clock-output-names = "nand";
+ };
+
+ dfx: dfx at 0 {
+ compatible = "marvell,dfx-server";
+ reg = <0 0x100000>;
+ };
+ };
+
+ switch {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 MBUS_ID(0x03, 0x00) 0 0x100000>;
+
+ pp0: packet-processor at 0 {
+ compatible = "marvell,prestera-98dx3236";
+ reg = <0 0x4000000>;
+ interrupts = <33>, <34>, <35>;
+ dfx = <&dfx>;
+ };
+ };
+ };
+};
+
+&pinctrl {
+ compatible = "marvell,98dx3236-pinctrl";
+
+ spi0_pins: spi0-pins {
+ marvell,pins = "mpp0", "mpp1",
+ "mpp2", "mpp3";
+ marvell,function = "spi0";
+ };
+};
+
+&sdio {
+ status = "disabled";
+};
+
+&crypto_sram0 {
+ status = "disabled";
+};
+
+&crypto_sram1 {
+ status = "disabled";
+};
diff --git a/arch/arm/boot/dts/armada-xp-98dx3336.dtsi b/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
new file mode 100644
index 000000000000..a9b0f47f8df9
--- /dev/null
+++ b/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
@@ -0,0 +1,76 @@
+/*
+ * Device Tree Include file for Marvell 98dx3336 family SoC
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Contains definitions specific to the 98dx3336 SoC that are not
+ * common to all Armada XP SoCs.
+ */
+
+#include "armada-xp-98dx3236.dtsi"
+
+/ {
+ model = "Marvell 98DX3336 SoC";
+ compatible = "marvell,armadaxp-98dx3336", "marvell,armadaxp-98dx3236", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ cpus {
+ cpu at 1 {
+ device_type = "cpu";
+ compatible = "marvell,sheeva-v7";
+ reg = <1>;
+ clocks = <&cpuclk 1>;
+ clock-latency = <1000000>;
+ };
+ };
+
+ soc {
+ internal-regs {
+ resume at 20980 {
+ compatible = "marvell,98dx3336-resume-ctrl";
+ reg = <0x20980 0x10>;
+ };
+ };
+ };
+};
+
+&pp0 {
+ compatible = "marvell,prestera-98dx3336";
+};
diff --git a/arch/arm/boot/dts/armada-xp-98dx4251.dtsi b/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
new file mode 100644
index 000000000000..446e6e65ec59
--- /dev/null
+++ b/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
@@ -0,0 +1,90 @@
+/*
+ * Device Tree Include file for Marvell 98dx4521 family SoC
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Contains definitions specific to the 98dx4521 SoC that are not
+ * common to all Armada XP SoCs.
+ */
+
+#include "armada-xp-98dx3236.dtsi"
+
+/ {
+ model = "Marvell 98DX4251 SoC";
+ compatible = "marvell,armadaxp-98dx4521", "marvell,armadaxp-98dx3236", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ cpus {
+ cpu at 1 {
+ device_type = "cpu";
+ compatible = "marvell,sheeva-v7";
+ reg = <1>;
+ clocks = <&cpuclk 1>;
+ clock-latency = <1000000>;
+ };
+ };
+
+ soc {
+ internal-regs {
+ resume at 20980 {
+ compatible = "marvell,98dx3336-resume-ctrl";
+ reg = <0x20980 0x10>;
+ };
+ };
+ };
+};
+
+&sdio {
+ status = "okay";
+};
+
+&pinctrl {
+ compatible = "marvell,98dx4251-pinctrl";
+
+ sdio_pins: sdio-pins {
+ marvell,pins = "mpp5", "mpp6", "mpp7",
+ "mpp8", "mpp9", "mpp10";
+ marvell,function = "sd0";
+ };
+};
+
+&pp0 {
+ compatible = "marvell,prestera-98dx4251";
+};
--
2.11.0.24.ge6920cf
^ permalink raw reply related
* [PATCHv3 5/5] arm: mvebu: Add device tree for db-dxbc2 and db-xc3-24g4xg boards
From: Chris Packham @ 2017-01-06 4:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20170106041517.9589-1-chris.packham@alliedtelesis.co.nz>
These boards are Marvell's evaluation boards for the 98DX4251 and
98DX3336 SoCs.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
Change in v2/v3:
- None
arch/arm/boot/dts/db-dxbc2.dts | 159 ++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/db-xc3-24g4xg.dts | 155 +++++++++++++++++++++++++++++++++++
2 files changed, 314 insertions(+)
create mode 100644 arch/arm/boot/dts/db-dxbc2.dts
create mode 100644 arch/arm/boot/dts/db-xc3-24g4xg.dts
diff --git a/arch/arm/boot/dts/db-dxbc2.dts b/arch/arm/boot/dts/db-dxbc2.dts
new file mode 100644
index 000000000000..f56786cea5f8
--- /dev/null
+++ b/arch/arm/boot/dts/db-dxbc2.dts
@@ -0,0 +1,159 @@
+/*
+ * Device Tree file for DB-DXBC2 board
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * Based on armada-xp-db.dts
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include "armada-xp-98dx4251.dtsi"
+
+/ {
+ model = "Marvell Bobcat2 Evaluation Board";
+ compatible = "marvell,db-dxbc2", "marvell,armadaxp-98dx4251", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 earlyprintk";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x00000000 0 0x20000000>; /* 512 MB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
+ MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
+ MBUS_ID(0x03, 0x00) 0 0 0xa8000000 0x4000000
+ MBUS_ID(0x08, 0x00) 0 0 0xac000000 0x100000>;
+
+ devbus-bootcs {
+ status = "okay";
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <16>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+ };
+
+ internal-regs {
+ serial at 12000 {
+ status = "okay";
+ };
+ serial at 12100 {
+ status = "okay";
+ };
+
+ i2c at 11000 {
+ clock-frequency = <100000>;
+ status = "okay";
+ };
+
+ mvsdio at d4000 {
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ /* No CD or WP GPIOs */
+ broken-cd;
+ };
+
+ nand at d0000 {
+ status = "okay";
+ num-cs = <1>;
+ marvell,nand-keep-config;
+ marvell,nand-enable-arbiter;
+ nand-on-flash-bbt;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ };
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p64";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <20000000>;
+ m25p,fast-read;
+
+ partition at u-boot {
+ reg = <0x00000000 0x00100000>;
+ label = "u-boot";
+ };
+ partition at u-boot-env {
+ reg = <0x00100000 0x00040000>;
+ label = "u-boot-env";
+ };
+ partition at unused {
+ reg = <0x00140000 0x00ec0000>;
+ label = "unused";
+ };
+
+ };
+};
diff --git a/arch/arm/boot/dts/db-xc3-24g4xg.dts b/arch/arm/boot/dts/db-xc3-24g4xg.dts
new file mode 100644
index 000000000000..5eb89ffb9a7d
--- /dev/null
+++ b/arch/arm/boot/dts/db-xc3-24g4xg.dts
@@ -0,0 +1,155 @@
+/*
+ * Device Tree file for DB-XC3-24G4XG board
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * Based on armada-xp-db.dts
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include "armada-xp-98dx3336.dtsi"
+
+/ {
+ model = "DB-XC3-24G4XG";
+ compatible = "marvell,db-xc3-24g4xg", "marvell,armadaxp-98dx3336", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 earlyprintk";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x00000000 0 0x40000000>; /* 1 GB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
+ MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
+ MBUS_ID(0x03, 0x00) 0 0 0xa8000000 0x4000000
+ MBUS_ID(0x08, 0x00) 0 0 0xac000000 0x100000>;
+
+ devbus-bootcs {
+ status = "okay";
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <16>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+ };
+
+ internal-regs {
+ serial at 12000 {
+ status = "okay";
+ };
+ serial at 12100 {
+ status = "okay";
+ };
+
+ i2c at 11000 {
+ clock-frequency = <100000>;
+ status = "okay";
+ };
+
+ mvsdio at d4000 {
+ status = "disabled";
+ };
+
+ nand at d0000 {
+ status = "okay";
+ num-cs = <1>;
+ marvell,nand-keep-config;
+ marvell,nand-enable-arbiter;
+ nand-on-flash-bbt;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ };
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p64";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <20000000>;
+ m25p,fast-read;
+
+ partition at u-boot {
+ reg = <0x00000000 0x00100000>;
+ label = "u-boot";
+ };
+ partition at u-boot-env {
+ reg = <0x00100000 0x00040000>;
+ label = "u-boot-env";
+ };
+ partition at unused {
+ reg = <0x00140000 0x00ec0000>;
+ label = "unused";
+ };
+
+ };
+};
--
2.11.0.24.ge6920cf
^ permalink raw reply related
* [PATCHv2 1/2] arm: Cleanup sanity_check_meminfo
From: Nicolas Pitre @ 2017-01-06 4:17 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483657274-11346-2-git-send-email-labbott@redhat.com>
On Thu, 5 Jan 2017, Laura Abbott wrote:
>
> The logic for sanity_check_meminfo has become difficult to
> follow. Clean up the code so it's more obvious what the code
> is actually trying to do. Additionally, meminfo is now removed
> so rename the function to better describe it's purpose.
s/it's/its/
> Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
> Signed-off-by: Laura Abbott <labbott@redhat.com>
> ---
> v2: Fixed code so b9a019899f61 ("ARM: 8590/1: sanity_check_meminfo():
> avoid overflow on vmalloc_limit") should stay fixed. The casting and assignment
> still seem ugly.
Are you referring to the initial vmalloc_limit assignment?
> @@ -1172,43 +1170,19 @@ void __init sanity_check_meminfo(void)
> for_each_memblock(memory, reg) {
> phys_addr_t block_start = reg->base;
> phys_addr_t block_end = reg->base + reg->size;
> - phys_addr_t size_limit = reg->size;
>
> - if (reg->base >= vmalloc_limit)
> - highmem = 1;
> - else
> - size_limit = vmalloc_limit - reg->base;
>
> -
[...]
This leaves a spurious empty line. One was already there before your
patch but this would be a good opportunity to remove it.
Other than that...
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Nicolas
^ permalink raw reply
* [PATCH v5 13/17] irqdomain: irq_domain_check_msi_remap
From: Bharat Bhushan @ 2017-01-06 4:27 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <a574e969-b46d-94fb-e4c2-646a37b17122@redhat.com>
Hi Mark,
> -----Original Message-----
> From: Auger Eric [mailto:eric.auger at redhat.com]
> Sent: Thursday, January 05, 2017 5:39 PM
> To: Marc Zyngier <marc.zyngier@arm.com>; eric.auger.pro at gmail.com;
> christoffer.dall at linaro.org; robin.murphy at arm.com;
> alex.williamson at redhat.com; will.deacon at arm.com; joro at 8bytes.org;
> tglx at linutronix.de; jason at lakedaemon.net; linux-arm-
> kernel at lists.infradead.org
> Cc: drjones at redhat.com; kvm at vger.kernel.org; punit.agrawal at arm.com;
> linux-kernel at vger.kernel.org; geethasowjanya.akula at gmail.com; Diana
> Madalina Craciun <diana.craciun@nxp.com>; iommu at lists.linux-
> foundation.org; pranav.sawargaonkar at gmail.com; Bharat Bhushan
> <bharat.bhushan@nxp.com>; shankerd at codeaurora.org;
> gpkulkarni at gmail.com
> Subject: Re: [PATCH v5 13/17] irqdomain: irq_domain_check_msi_remap
>
> Hi Marc,
>
> On 05/01/2017 12:57, Marc Zyngier wrote:
> > On 05/01/17 11:29, Auger Eric wrote:
> >> Hi Marc,
> >>
> >> On 05/01/2017 12:25, Marc Zyngier wrote:
> >>> On 05/01/17 10:45, Auger Eric wrote:
> >>>> Hi Marc,
> >>>>
> >>>> On 04/01/2017 16:27, Marc Zyngier wrote:
> >>>>> On 04/01/17 14:11, Auger Eric wrote:
> >>>>>> Hi Marc,
> >>>>>>
> >>>>>> On 04/01/2017 14:46, Marc Zyngier wrote:
> >>>>>>> Hi Eric,
> >>>>>>>
> >>>>>>> On 04/01/17 13:32, Eric Auger wrote:
> >>>>>>>> This new function checks whether all platform and PCI MSI
> >>>>>>>> domains implement IRQ remapping. This is useful to understand
> >>>>>>>> whether VFIO passthrough is safe with respect to interrupts.
> >>>>>>>>
> >>>>>>>> On ARM typically an MSI controller can sit downstream to the
> >>>>>>>> IOMMU without preventing VFIO passthrough.
> >>>>>>>> As such any assigned device can write into the MSI doorbell.
> >>>>>>>> In case the MSI controller implements IRQ remapping, assigned
> >>>>>>>> devices will not be able to trigger interrupts towards the
> >>>>>>>> host. On the contrary, the assignment must be emphasized as
> >>>>>>>> unsafe with respect to interrupts.
> >>>>>>>>
> >>>>>>>> Signed-off-by: Eric Auger <eric.auger@redhat.com>
> >>>>>>>>
> >>>>>>>> ---
> >>>>>>>>
> >>>>>>>> v4 -> v5:
> >>>>>>>> - Handle DOMAIN_BUS_FSL_MC_MSI domains
> >>>>>>>> - Check parents
> >>>>>>>> ---
> >>>>>>>> include/linux/irqdomain.h | 1 +
> >>>>>>>> kernel/irq/irqdomain.c | 41
> +++++++++++++++++++++++++++++++++++++++++
> >>>>>>>> 2 files changed, 42 insertions(+)
> >>>>>>>>
> >>>>>>>> diff --git a/include/linux/irqdomain.h
> >>>>>>>> b/include/linux/irqdomain.h index ab017b2..281a40f 100644
> >>>>>>>> --- a/include/linux/irqdomain.h
> >>>>>>>> +++ b/include/linux/irqdomain.h
> >>>>>>>> @@ -219,6 +219,7 @@ struct irq_domain
> *irq_domain_add_legacy(struct device_node *of_node,
> >>>>>>>> void *host_data);
> >>>>>>>> extern struct irq_domain *irq_find_matching_fwspec(struct
> irq_fwspec *fwspec,
> >>>>>>>> enum
> irq_domain_bus_token bus_token);
> >>>>>>>> +extern bool irq_domain_check_msi_remap(void);
> >>>>>>>> extern void irq_set_default_host(struct irq_domain *host);
> >>>>>>>> extern int irq_domain_alloc_descs(int virq, unsigned int nr_irqs,
> >>>>>>>> irq_hw_number_t hwirq, int node,
> diff --git
> >>>>>>>> a/kernel/irq/irqdomain.c b/kernel/irq/irqdomain.c index
> >>>>>>>> 8c0a0ae..700caea 100644
> >>>>>>>> --- a/kernel/irq/irqdomain.c
> >>>>>>>> +++ b/kernel/irq/irqdomain.c
> >>>>>>>> @@ -278,6 +278,47 @@ struct irq_domain
> >>>>>>>> *irq_find_matching_fwspec(struct irq_fwspec *fwspec,
> >>>>>>>> EXPORT_SYMBOL_GPL(irq_find_matching_fwspec);
> >>>>>>>>
> >>>>>>>> /**
> >>>>>>>> + * irq_domain_is_msi_remap - Check if @domain or any parent
> >>>>>>>> + * has MSI remapping support
> >>>>>>>> + * @domain: domain pointer
> >>>>>>>> + */
> >>>>>>>> +static bool irq_domain_is_msi_remap(struct irq_domain
> *domain)
> >>>>>>>> +{
> >>>>>>>> + struct irq_domain *h = domain;
> >>>>>>>> +
> >>>>>>>> + for (; h; h = h->parent) {
> >>>>>>>> + if (h->flags & IRQ_DOMAIN_FLAG_MSI_REMAP)
> >>>>>>>> + return true;
> >>>>>>>> + }
> >>>>>>>> + return false;
> >>>>>>>> +}
> >>>>>>>> +
> >>>>>>>> +/**
> >>>>>>>> + * irq_domain_check_msi_remap() - Checks whether all MSI
> >>>>>>>> + * irq domains implement IRQ remapping */ bool
> >>>>>>>> +irq_domain_check_msi_remap(void) {
> >>>>>>>> + struct irq_domain *h;
> >>>>>>>> + bool ret = true;
> >>>>>>>> +
> >>>>>>>> + mutex_lock(&irq_domain_mutex);
> >>>>>>>> + list_for_each_entry(h, &irq_domain_list, link) {
> >>>>>>>> + if (((h->bus_token & DOMAIN_BUS_PCI_MSI) ||
> >>>>>>>> + (h->bus_token & DOMAIN_BUS_PLATFORM_MSI)
> ||
> >>>>>>>> + (h->bus_token & DOMAIN_BUS_FSL_MC_MSI))
> &&
> >>>>>>>> + !irq_domain_is_msi_remap(h)) {
> >>>>>>>
> >>>>>>> (h->bus_token & DOMAIN_BUS_PCI_MSI) and co looks quite
> wrong.
> >>>>>>> bus_token is not a bitmap, and DOMAIN_BUS_* not a single bit
> >>>>>>> value (see enum irq_domain_bus_token). Surely this should read
> >>>>>>> (h->bus_token == DOMAIN_BUS_PCI_MSI).
> >>>>>> Oh I did not notice that. Thanks.
> >>>>>>
> >>>>>> Any other comments on the irqdomain side? Do you think the
> >>>>>> current approach consisting in looking at those bus tokens and
> >>>>>> their parents looks good?
> >>>>>
> >>>>> To be completely honest, I don't like it much, as having to
> >>>>> enumerate all the bus types can come up with could become quite a
> >>>>> burden in the long run. I'd rather be able to identify MSI capable
> >>>>> domains by construction. I came up with the following approach (fully
> untested):
> >>>>>
> >>>>> diff --git a/include/linux/irqdomain.h b/include/linux/irqdomain.h
> >>>>> index 281a40f..7779796 100644
> >>>>> --- a/include/linux/irqdomain.h
> >>>>> +++ b/include/linux/irqdomain.h
> >>>>> @@ -183,8 +183,11 @@ enum {
> >>>>> /* Irq domain is an IPI domain with single virq */
> >>>>> IRQ_DOMAIN_FLAG_IPI_SINGLE = (1 << 3),
> >>>>>
> >>>>> + /* Irq domain implements MSIs */
> >>>>> + IRQ_DOMAIN_FLAG_MSI = (1 << 4),
> >>>>> +
> >>>>> /* Irq domain is MSI remapping capable */
> >>>>> - IRQ_DOMAIN_FLAG_MSI_REMAP = (1 << 4),
> >>>>> + IRQ_DOMAIN_FLAG_MSI_REMAP = (1 << 5),
> >>>>>
> >>>>> /*
> >>>>> * Flags starting from IRQ_DOMAIN_FLAG_NONCORE are reserved
> @@
> >>>>> -450,6 +453,11 @@ static inline bool
> >>>>> irq_domain_is_ipi_single(struct irq_domain *domain) {
> >>>>> return domain->flags & IRQ_DOMAIN_FLAG_IPI_SINGLE; }
> >>>>> +
> >>>>> +static inline bool irq_domain_is_msi(struct irq_domain *domain) {
> >>>>> + return domain->flags & IRQ_DOMAIN_FLAG_MSI; }
> >>>>> #else /* CONFIG_IRQ_DOMAIN_HIERARCHY */
> >>>>> static inline void irq_domain_activate_irq(struct irq_data *data)
> >>>>> { } static inline void irq_domain_deactivate_irq(struct irq_data
> >>>>> *data) { } @@ -481,6 +489,11 @@ static inline bool
> >>>>> irq_domain_is_ipi_single(struct irq_domain *domain) {
> >>>>> return false;
> >>>>> }
> >>>>> +
> >>>>> +static inline bool irq_domain_is_msi(struct irq_domain *domain) {
> >>>>> + return false;
> >>>>> +}
> >>>>> #endif /* CONFIG_IRQ_DOMAIN_HIERARCHY */
> >>>>>
> >>>>> #else /* CONFIG_IRQ_DOMAIN */
> >>>>> diff --git a/kernel/irq/irqdomain.c b/kernel/irq/irqdomain.c index
> >>>>> 700caea..33b6921 100644
> >>>>> --- a/kernel/irq/irqdomain.c
> >>>>> +++ b/kernel/irq/irqdomain.c
> >>>>> @@ -304,10 +304,7 @@ bool irq_domain_check_msi_remap(void)
> >>>>>
> >>>>> mutex_lock(&irq_domain_mutex);
> >>>>> list_for_each_entry(h, &irq_domain_list, link) {
> >>>>> - if (((h->bus_token & DOMAIN_BUS_PCI_MSI) ||
> >>>>> - (h->bus_token & DOMAIN_BUS_PLATFORM_MSI)
> ||
> >>>>> - (h->bus_token & DOMAIN_BUS_FSL_MC_MSI))
> &&
> >>>>> - !irq_domain_is_msi_remap(h)) {
> >>>>> + if (irq_domain_is_msi(h) &&
> !irq_domain_is_msi_remap(h)) {
> >>>>> ret = false;
> >>>>> goto out;
> >>>>> }
> >>>>> diff --git a/kernel/irq/msi.c b/kernel/irq/msi.c index
> >>>>> ee23006..b637263 100644
> >>>>> --- a/kernel/irq/msi.c
> >>>>> +++ b/kernel/irq/msi.c
> >>>>> @@ -270,7 +270,7 @@ struct irq_domain
> *msi_create_irq_domain(struct fwnode_handle *fwnode,
> >>>>> if (info->flags & MSI_FLAG_USE_DEF_CHIP_OPS)
> >>>>> msi_domain_update_chip_ops(info);
> >>>>>
> >>>>> - return irq_domain_create_hierarchy(parent, 0, 0, fwnode,
> >>>>> + return irq_domain_create_hierarchy(parent,
> IRQ_DOMAIN_FLAG_MSI,
> >>>>> +0, fwnode,
> >>>>> &msi_domain_ops, info);
> >>>>> }
> >>>>>
> >>>>>
> >>>>>
> >>>>> Thoughts?
> >>>>
> >>>> Don't we need to set the IRQ_DOMAIN_FLAG_MSI flag in
> >>>> platform_msi_create_device_domain too (drivers/base/platform-
> msi.c)?
> >> was mentioning platform_msi_create_*device*_domain.
> >> it calls irq_domain_create_hierarchy and looks to be MSI irq domain
> >> related. But I don't have a full understanding of the whole irq
> >> domain hierarchy.
> >
> > Ah, sorry - I blame the ARM coffee.
> >
> > This function builds a domain for a single device on top of the MSI
> > domain that has been already created (see the dev->msi_domain passed
> > to irq_domain_create_hierarchy). The structure looks like this:
> >
> > device-domain -> platform MSI domain -> HW MSI domain -> whatever
> >
> > So what we're *really* interested in is the platform MSI domain, which
> > is going to carry the IRQ_DOMAIN_FLAG_MSI flag. The device-domain only
> > describes a portion of it, and can safely be ignored.
> >
> > In the end, what matters for this patch is that we can prove that from
> > any domain carrying the IRQ_DOMAIN_FLAG_MSI flag, we can find a
> domain
> > carrying the IRQ_DOMAIN_FLAG_MSI_REMAP flag. If that property holds,
> > we're safe. Otherwise, we disable the Guest MSI feature.
> >
> > Does it make sense?
> Yes it makes sense. Thank you for the explanation!
If I understood correctly then the domain hierarchy is
-> "gic-irq-domain"
-> "gic-its-irq-domain"
-> "platform-msi-domain"
-> "pci-msi-domain"
-> "fsl-mc-msi-domain"
"gic-its-irq-domain" carries IRQ_DOMAIN_FLAG_MSI_REMAP
So we need to look for the IRQ_DOMAIN_FLAG_MSI_REMAP flag in "gic-its-irq-domain" when doing safety check for "platform/pci/fsl-mc"-msi-irqdomain, is this what you mentioned?
Can we can pass this flags from "gic-its-irq-domain" to "platform/pci/fsl-mc"-msi-irqdomain during domain creation?
Thanks
-Bharat
>
> Eric
> >
> > Thanks,
> >
> > M.
> >
^ permalink raw reply
* [PATCH v2 0/5] Support for LEGO MINDSTORMS EV3
From: David Lechner @ 2017-01-06 4:33 UTC (permalink / raw)
To: linux-arm-kernel
This patch series adds support for LEGO MINDSTORMS EV3. This is a TI AM1808
based board.
v2 changes:
* Dropped defconfig patches that have already been pick up
* Added some new defconfig patches
* Updated device tree file based on feedback and new available bindings
* Renamed file to include da850- prefix
* Changed button labels
* Fixed LED names
* Added beeper device for sound
* Added regulators for USB and A/DC
* Removed unused pinmux nodes
* Added pinconf for buttons
* Enabled pwms
* Used preferred bindings for flash partitions
* Added A/DC spi device
* Enabled USB
This patch series has been tested working on next-20170105 with linux-davinci/
next merged into it, along with a few other patches that have been submitted.
Dependencies:
i.e. Things that are not in next-20170105 or linux-davinci/next already. I know
this seems like a long list, but most of these are just small fixes and not
necessarily strict dependencies.
* "iio: adc: New driver for TI ADS7950 chips" [1]
This patch is currently in iio/testing. It is expected to be included as-is
in v4.11.
* "ARM: davinci: Allocate extra interrupts" [2]
This patch has been submitted but has not received any feedback. It is not
critical, but needed to use the trigger capabilities of iio.
* "spi: davinci: Allow device tree devices to use DMA" [3]
This has been (re)submitted, but no response from spi maintainer yet. It is
needed for the flash memory to work correctly.
* "ARM: dts: da850: Add usb device node" [4]
The dependencies that were holding up this patch are all merged, so it is OK
to pick up this patch in linux-davinci now.
* "regulator: fixed: Handle optional overcurrent pin" [5]
This is used by the USB/input port/output port/ADC regulator. This patch has
been slow in getting accepted into regulator.
* "serial: 8250: Add new port type for TI DA8xx/66AK2x" [6]
"ARM: da850: Add ti,da830-uart compatible for serial ports" [7]
This series fixes UART0 and UART2 not working. Waiting for patch to be picked
up in serial tree.
* "Input: pwm-beeper: add optional enable gpio" [8]
I just submitted this patch, so we will see what happens. It is needed for
the speaker to actually make sound.
[1]: https://patchwork.kernel.org/patch/9449767/
[2]: https://patchwork.kernel.org/patch/9438709/
[3]: https://patchwork.kernel.org/patch/9499937/
[4]: https://patchwork.kernel.org/patch/9439839/
[5]: https://patchwork.kernel.org/patch/9476509/
[6]: https://patchwork.kernel.org/patch/9499459/
[7]: https://patchwork.kernel.org/patch/9499457/
[8]: https://patchwork.kernel.org/patch/9499919/
David Lechner (5):
ARM: davinci_all_defconfig: enable DA8xx pinconf
ARM: davinci_all_defconfig: Enable PWM modules
ARM: davinci_all_defconfig: enable iio and ADS7950
ARM: davinci_all_defconfig: enable pwm-beeper
ARM: dts: Add LEGO MINDSTORMS EV3 dts
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/da850-lego-ev3.dts | 381 +++++++++++++++++++++++++++++++++
arch/arm/configs/davinci_all_defconfig | 12 ++
3 files changed, 395 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/da850-lego-ev3.dts
--
2.7.4
^ permalink raw reply
* [PATCH v2 1/5] ARM: davinci_all_defconfig: enable DA8xx pinconf
From: David Lechner @ 2017-01-06 4:33 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483677228-2325-1-git-send-email-david@lechnology.com>
This enables the DA8xx pinconf driver by default. It is needed by LEGO
MINDSTORMS EV3.
---
arch/arm/configs/davinci_all_defconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/configs/davinci_all_defconfig b/arch/arm/configs/davinci_all_defconfig
index ddb586a..a12e4c2 100644
--- a/arch/arm/configs/davinci_all_defconfig
+++ b/arch/arm/configs/davinci_all_defconfig
@@ -114,6 +114,7 @@ CONFIG_I2C_CHARDEV=y
CONFIG_I2C_DAVINCI=y
CONFIG_SPI=y
CONFIG_SPI_DAVINCI=m
+CONFIG_PINCTRL_DA850_PUPD=m
CONFIG_PINCTRL_SINGLE=y
CONFIG_GPIO_SYSFS=y
CONFIG_GPIO_PCA953X=y
--
2.7.4
^ permalink raw reply related
* [PATCH v2 2/5] ARM: davinci_all_defconfig: Enable PWM modules
From: David Lechner @ 2017-01-06 4:33 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483677228-2325-1-git-send-email-david@lechnology.com>
This enables PWM and the TI ECAP and EHRWPM modules. These are used on LEGO
MINDSTORMS EV3.
---
arch/arm/configs/davinci_all_defconfig | 3 +++
1 file changed, 3 insertions(+)
diff --git a/arch/arm/configs/davinci_all_defconfig b/arch/arm/configs/davinci_all_defconfig
index a12e4c2..2b1967a 100644
--- a/arch/arm/configs/davinci_all_defconfig
+++ b/arch/arm/configs/davinci_all_defconfig
@@ -200,6 +200,9 @@ CONFIG_TI_EDMA=y
CONFIG_MEMORY=y
CONFIG_TI_AEMIF=m
CONFIG_DA8XX_DDRCTL=y
+CONFIG_PWM=y
+CONFIG_PWM_TIECAP=m
+CONFIG_PWM_TIEHRPWM=m
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
CONFIG_EXT4_FS_POSIX_ACL=y
--
2.7.4
^ permalink raw reply related
* [PATCH v2 3/5] ARM: davinci_all_defconfig: enable iio and ADS7950
From: David Lechner @ 2017-01-06 4:33 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483677228-2325-1-git-send-email-david@lechnology.com>
This enables the iio subsystem and the TI ADS7950 driver. This is used by
LEGO MINDSTORMS EV3, which has an ADS7957 chip.
---
The CONFIG_TI_ADS7950 driver is currently in iio/testing, so some coordination
may be needed before picking up this patch.
arch/arm/configs/davinci_all_defconfig | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/arch/arm/configs/davinci_all_defconfig b/arch/arm/configs/davinci_all_defconfig
index 2b1967a..a899876 100644
--- a/arch/arm/configs/davinci_all_defconfig
+++ b/arch/arm/configs/davinci_all_defconfig
@@ -200,6 +200,13 @@ CONFIG_TI_EDMA=y
CONFIG_MEMORY=y
CONFIG_TI_AEMIF=m
CONFIG_DA8XX_DDRCTL=y
+CONFIG_IIO=m
+CONFIG_IIO_BUFFER_CB=m
+CONFIG_IIO_SW_DEVICE=m
+CONFIG_IIO_SW_TRIGGER=m
+CONFIG_TI_ADS7950=m
+CONFIG_IIO_HRTIMER_TRIGGER=m
+CONFIG_IIO_SYSFS_TRIGGER=m
CONFIG_PWM=y
CONFIG_PWM_TIECAP=m
CONFIG_PWM_TIEHRPWM=m
--
2.7.4
^ permalink raw reply related
* [PATCH v2 4/5] ARM: davinci_all_defconfig: enable pwm-beeper
From: David Lechner @ 2017-01-06 4:33 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483677228-2325-1-git-send-email-david@lechnology.com>
This enables the pwm-beeper module. This is used by the speaker on LEGO
MINDSTORMS EV3.
Signed-off-by: David Lechner <david@lechnology.com>
---
arch/arm/configs/davinci_all_defconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/configs/davinci_all_defconfig b/arch/arm/configs/davinci_all_defconfig
index a899876..e046fd7 100644
--- a/arch/arm/configs/davinci_all_defconfig
+++ b/arch/arm/configs/davinci_all_defconfig
@@ -100,6 +100,7 @@ CONFIG_KEYBOARD_XTKBD=m
# CONFIG_INPUT_MOUSE is not set
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_INPUT_MISC=y
+CONFIG_INPUT_PWM_BEEPER=m
CONFIG_INPUT_DM355EVM=m
CONFIG_SERIO_LIBPS2=y
# CONFIG_VT_CONSOLE is not set
--
2.7.4
^ permalink raw reply related
* [PATCH v2 5/5] ARM: dts: Add LEGO MINDSTORMS EV3 dts
From: David Lechner @ 2017-01-06 4:33 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483677228-2325-1-git-send-email-david@lechnology.com>
This adds a device tree definition file for LEGO MINDSTORMS EV3.
What is working:
* Pin muxing
* Pinconf
* GPIOs
* MicroSD card reader
* UART on input ports 1 and 2
* Buttons
* LEDs
* Poweroff/reset
* Flash memory
* EEPROM
* Speaker
* USB host port
* USB perepheral port
* A/DC chip
What is not working/to be added later:
* Display - waiting for "simple DRM" to be mainlined
* Bluetooth - needs new driver for sequencing power/enable/clock - usable
now by manipulating gpios/pwm in userspace
* Input and output ports - need some sort of new phy or extcon driver
* Battery indication - needs new power supply driver
Note on flash partitions:
These partitions are based on the official EV3 firmware from LEGO. It is
expected that most users of the mainline kernel on EV3 will be booting from
an SD card while retaining the official firmware in the flash memory.
Furthermore, the official firmware uses an ancient U-Boot (2009) that has
no device tree support. So, it makes sense to have this partition table in
the EV3 device tree file. In the unlikely case that anyone does create their
own firmware image with different partitioning, they can use a modern
U-Boot in that firmware image that modifies the device tree with the custom
partitions.
Signed-off-by: David Lechner <david@lechnology.com>
---
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/da850-lego-ev3.dts | 381 +++++++++++++++++++++++++++++++++++
2 files changed, 383 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/da850-lego-ev3.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9a7375c..471b802 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -128,7 +128,8 @@ dtb-$(CONFIG_ARCH_CLPS711X) += \
dtb-$(CONFIG_ARCH_DAVINCI) += \
da850-lcdk.dtb \
da850-enbw-cmc.dtb \
- da850-evm.dtb
+ da850-evm.dtb \
+ da850-lego-ev3.dtb
dtb-$(CONFIG_ARCH_DIGICOLOR) += \
cx92755_equinox.dtb
dtb-$(CONFIG_ARCH_EFM32) += \
diff --git a/arch/arm/boot/dts/da850-lego-ev3.dts b/arch/arm/boot/dts/da850-lego-ev3.dts
new file mode 100644
index 0000000..d720c58
--- /dev/null
+++ b/arch/arm/boot/dts/da850-lego-ev3.dts
@@ -0,0 +1,381 @@
+/*
+ * Device tree for LEGO MINDSTORMS EV3
+ *
+ * Copyright (C) 2017 David Lechner <david@lechnology.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation, version 2.
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/pwm/pwm.h>
+
+#include "da850.dtsi"
+
+/ {
+ compatible = "lego,ev3", "ti,da850";
+ model = "LEGO MINDSTORMS EV3";
+
+ /*
+ * The buttons on the EV3 are mapped to keyboard keys.
+ */
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ label = "Brick buttons";
+ pinctrl-names = "default";
+ pinctrl-0 = <&button_pins>, <&button_bias>;
+
+ enter {
+ label = "Brick button ENTER";
+ linux,code = <KEY_ENTER>;
+ gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+ };
+ left {
+ label = "Brick button LEFT";
+ linux,code = <KEY_LEFT>;
+ gpios = <&gpio 102 GPIO_ACTIVE_HIGH>;
+ };
+ back {
+ label = "Brick button BACK";
+ linux,code = <KEY_BACKSPACE>;
+ gpios = <&gpio 106 GPIO_ACTIVE_HIGH>;
+ };
+ right {
+ label = "Brick button RIGHT";
+ linux,code = <KEY_RIGHT>;
+ gpios = <&gpio 124 GPIO_ACTIVE_HIGH>;
+ };
+ down {
+ label = "Brick button DOWN";
+ linux,code = <KEY_DOWN>;
+ gpios = <&gpio 126 GPIO_ACTIVE_HIGH>;
+ };
+ up {
+ label = "Brick button UP";
+ linux,code = <KEY_UP>;
+ gpios = <&gpio 127 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ /*
+ * The EV3 has two built-in bi-color LEDs behind the buttons.
+ */
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins>;
+
+ left_green {
+ label = "led0:green:brick-status";
+ /* GP6[13] */
+ gpios = <&gpio 103 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+ right_red {
+ label = "led1:red:brick-status";
+ /* GP6[7] */
+ gpios = <&gpio 108 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+ left_red {
+ label = "led0:red:brick-status";
+ /* GP6[12] */
+ gpios = <&gpio 109 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+ right_green {
+ label = "led1:green:brick-status";
+ /* GP6[14] */
+ gpios = <&gpio 110 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+ };
+
+ beeper {
+ compatible = "pwm-beeper";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ehrpwm0b_pins>, <&_pins>;
+ pwms = <&ehrpwm0 1 0 0>;
+ enable-gpios = <&gpio 111 GPIO_ACTIVE_HIGH>;
+ };
+
+ /*
+ * The EV3 is powered down by turning off the main 5V supply.
+ */
+ gpio-poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio 107 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&system_power_pin>;
+ };
+
+ /*
+ * The Bluetooth chip requires a clock at 32768Hz. One of the PWMs
+ * is used to generate this signal.
+ */
+ bt-slow-clock {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "slow_clk";
+ pwms = <&ecap2 0 30517>;
+ };
+
+ /*
+ * This is a 5V current limiting regulator that is shared by USB,
+ * the sensor (input) ports, the motor (output) ports and the A/DC.
+ */
+ vcc5v: regulator1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v_pins>;
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-supply";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio 101 0>;
+ over-current-gpios = <&gpio 99 GPIO_ACTIVE_LOW>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ /*
+ * This is a simple voltage divider on VCC5V to provide a 2.5V
+ * reference signal to the ADC.
+ */
+ adc_ref: regulator2 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-supply";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-boot-on;
+ vin-supply = <&vcc5v>;
+ };
+};
+
+&pmx_core {
+ status = "okay";
+
+ spi0_cs3_pin: pinmux_spi0_cs3_pin {
+ pinctrl-single,bits = <
+ /* CS3 */
+ 0xc 0x01000000 0x0f000000
+ >;
+ };
+ mmc0_cd_pin: pinmux_mmc0_cd {
+ pinctrl-single,bits = <
+ /* GP5[14] */
+ 0x2C 0x00000080 0x000000f0
+ >;
+ };
+ button_pins: pinmux_button_pins {
+ pinctrl-single,bits = <
+ /* GP1[13] */
+ 0x8 0x00000800 0x00000f00
+ /* GP6[10] */
+ 0x34 0x00800000 0x00f00000
+ /* GP6[6] */
+ 0x38 0x00000080 0x000000f0
+ /* GP7[12], GP7[14], GP7[15] */
+ 0x40 0x00808800 0x00f0ff00
+ >;
+ };
+ led_pins: pinmux_led_pins {
+ pinctrl-single,bits = <
+ /* GP6[12], GP6[13], GP6[14] */
+ 0x34 0x00008880 0x0000fff0
+ /* GP6[7] */
+ 0x38 0x00000008 0x0000000f
+ >;
+ };
+ amp_pins: pinmux_amp_pins {
+ pinctrl-single,bits = <
+ /* GP6[15] */
+ 0x34 0x00000008 0x0000000f
+ >;
+ };
+ system_power_pin: pinmux_system_power {
+ pinctrl-single,bits = <
+ /* GP6[11] */
+ 0x34 0x00080000 0x000f0000
+ >;
+ };
+ vcc5v_pins: pinmux_vcc5v {
+ pinctrl-single,bits = <
+ /* GP6[5] */
+ 0x40 0x00000080 0x000000f0
+ /* GP6[3] */
+ 0x4c 0x00008000 0x0000f000
+ >;
+ };
+};
+
+&pinconf {
+ status = "okay";
+
+ /* Buttons have external pulldown resistors */
+ button_bias: button-bias-groups {
+ disable {
+ groups = "cp5", "cp24", "cp25", "cp28";
+ bias-disable;
+ };
+ };
+};
+
+/* Input port 2 */
+&serial0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&serial0_rxtx_pins>;
+};
+
+/* Input port 1 */
+&serial1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&serial1_rxtx_pins>;
+};
+
+/* Bluetooth */
+&serial2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&serial2_rxtx_pins>, <&serial2_rtscts_pins>;
+};
+
+&rtc0 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ /*
+ * EEPROM contains the first stage bootloader, HW ID and Bluetooth MAC.
+ */
+ eeprom at 50 {
+ compatible = "at24,24c128";
+ pagesize = <64>;
+ read-only;
+ reg = <0x50>;
+ };
+};
+
+&wdt {
+ status = "okay";
+};
+
+&mmc0 {
+ status = "okay";
+ max-frequency = <50000000>;
+ bus-width = <4>;
+ cd-gpios = <&gpio 94 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin>;
+};
+
+&ehrpwm0 {
+ status = "okay";
+};
+
+&ehrpwm1 {
+ status = "okay";
+ pinctrl-names = "default";
+ /* MBPWM, MAPWM */
+ pinctrl-0 = <&ehrpwm1a_pins>, <&ehrpwm1b_pins>;
+};
+
+&ecap0 {
+ status = "okay";
+ pinctrl-names = "default";
+ /* MCPWM */
+ pinctrl-0 = <&ecap0_pins>;
+};
+
+&ecap1 {
+ status = "okay";
+ pinctrl-names = "default";
+ /* MDPWM */
+ pinctrl-0 = <&ecap1_pins>;
+};
+
+&ecap2 {
+ status = "okay";
+ pinctrl-names = "default";
+ /* BTSLOWCLK */
+ pinctrl-0 = <&ecap2_pins>;
+};
+
+&spi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>, <&spi0_cs3_pin>;
+
+ flash at 0 {
+ compatible = "n25q128a13", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ ti,spi-wdelay = <8>;
+
+ /* Partitions are based on the official firmware from LEGO */
+ partitions {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition at 0 {
+ label = "U-Boot";
+ reg = <0 0x40000>;
+ };
+
+ partition at 40000 {
+ label = "U-Boot Env";
+ reg = <0x40000 0x10000>;
+ };
+
+ partition at 50000 {
+ label = "Kernel";
+ reg = <0x50000 0x200000>;
+ };
+
+ partition at 250000 {
+ label = "Filesystem";
+ reg = <0x250000 0xa50000>;
+ };
+
+ partition at cb0000 {
+ label = "Storage";
+ reg = <0xcb0000 0x2f0000>;
+ };
+ };
+ };
+
+ adc at 3 {
+ compatible = "ti-ads7957";
+ reg = <3>;
+ spi-max-frequency = <10000000>;
+ refin-supply = <&adc_ref>;
+ };
+};
+
+&gpio {
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+ vbus-supply = <&vcc5v>;
+};
--
2.7.4
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox