* [PATCH 078/102] arm64: dts: renesas: r8a7796: Correct whitespace
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Geert Uytterhoeven <geert+renesas@glider.be>
Add missing spaces after commas.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796.dtsi | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 3fbd86590fb0..6ffab2da07cb 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -143,7 +143,7 @@
};
a57_1: cpu at 1 {
- compatible = "arm,cortex-a57","arm,armv8";
+ compatible = "arm,cortex-a57", "arm,armv8";
reg = <0x1>;
device_type = "cpu";
power-domains = <&sysc R8A7796_PD_CA57_CPU1>;
@@ -166,7 +166,7 @@
};
a53_1: cpu at 101 {
- compatible = "arm,cortex-a53","arm,armv8";
+ compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x101>;
device_type = "cpu";
power-domains = <&sysc R8A7796_PD_CA53_CPU1>;
@@ -177,7 +177,7 @@
};
a53_2: cpu at 102 {
- compatible = "arm,cortex-a53","arm,armv8";
+ compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x102>;
device_type = "cpu";
power-domains = <&sysc R8A7796_PD_CA53_CPU2>;
@@ -188,7 +188,7 @@
};
a53_3: cpu at 103 {
- compatible = "arm,cortex-a53","arm,armv8";
+ compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x103>;
device_type = "cpu";
power-domains = <&sysc R8A7796_PD_CA53_CPU3>;
--
2.11.0
^ permalink raw reply related
* [PATCH 077/102] arm64: dts: renesas: r8a7795: Correct whitespace
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Geert Uytterhoeven <geert+renesas@glider.be>
Add missing spaces after commas.
Replace 8 consecutive spaces by a TAB.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795.dtsi | 14 +++++++-------
1 file changed, 7 insertions(+), 7 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
index 9b080a864ea1..91486b4910ce 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
@@ -132,7 +132,7 @@
};
a57_1: cpu at 1 {
- compatible = "arm,cortex-a57","arm,armv8";
+ compatible = "arm,cortex-a57", "arm,armv8";
reg = <0x1>;
device_type = "cpu";
power-domains = <&sysc R8A7795_PD_CA57_CPU1>;
@@ -144,7 +144,7 @@
};
a57_2: cpu at 2 {
- compatible = "arm,cortex-a57","arm,armv8";
+ compatible = "arm,cortex-a57", "arm,armv8";
reg = <0x2>;
device_type = "cpu";
power-domains = <&sysc R8A7795_PD_CA57_CPU2>;
@@ -156,7 +156,7 @@
};
a57_3: cpu at 3 {
- compatible = "arm,cortex-a57","arm,armv8";
+ compatible = "arm,cortex-a57", "arm,armv8";
reg = <0x3>;
device_type = "cpu";
power-domains = <&sysc R8A7795_PD_CA57_CPU3>;
@@ -179,7 +179,7 @@
};
a53_1: cpu at 101 {
- compatible = "arm,cortex-a53","arm,armv8";
+ compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x101>;
device_type = "cpu";
power-domains = <&sysc R8A7795_PD_CA53_CPU1>;
@@ -190,7 +190,7 @@
};
a53_2: cpu at 102 {
- compatible = "arm,cortex-a53","arm,armv8";
+ compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x102>;
device_type = "cpu";
power-domains = <&sysc R8A7795_PD_CA53_CPU2>;
@@ -201,7 +201,7 @@
};
a53_3: cpu at 103 {
- compatible = "arm,cortex-a53","arm,armv8";
+ compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x103>;
device_type = "cpu";
power-domains = <&sysc R8A7795_PD_CA53_CPU3>;
@@ -262,7 +262,7 @@
pmu_a57 {
compatible = "arm,cortex-a57-pmu";
interrupts-extended = <&gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
- <&gic GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+ <&gic GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
<&gic GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
<&gic GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
interrupt-affinity = <&a57_0>,
--
2.11.0
^ permalink raw reply related
* [PATCH 076/102] arm64: dts: renesas: r8a7795: salvator-xs: enable USB2.0 host channel 3
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
This patch enables USB2.0 host channel 3 for r8a7795 with Salvator-XS.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts
index bbf5a8812b70..e231b5a7cbab 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts
@@ -56,6 +56,11 @@
status = "okay";
};
+&ehci3 {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&hsusb3 {
dr_mode = "otg";
status = "okay";
@@ -117,6 +122,11 @@
status = "okay";
};
+&ohci3 {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&rcar_sound {
ports {
/* rsnd_port0 is on salvator-common */
--
2.11.0
^ permalink raw reply related
* [PATCH 075/102] arm64: dts: renesas: r8a7795: salvator-xs: enable hsusb channel 3 node
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
This patch enables HS-USB channel3 node for r8a7795 with Salvator-XS.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts
index 622b2a22ab0f..bbf5a8812b70 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts
@@ -56,6 +56,11 @@
status = "okay";
};
+&hsusb3 {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&sound_card {
dais = <&rsnd_port0 /* ak4613 */
&rsnd_port1 /* HDMI0 */
--
2.11.0
^ permalink raw reply related
* [PATCH 074/102] arm64: dts: renesas: r8a7795: salvator-xs: enable usb2_phy3 node
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
This patch enables usb2_phy3 node for r8a7795 with Salvator-XS.
You must change the SW31 to OFF-OFF-ON-ON-ON-ON on the board.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
.../arm64/boot/dts/renesas/r8a7795-salvator-xs.dts | 24 ++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts
index 83676684c6b4..622b2a22ab0f 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts
@@ -145,6 +145,23 @@
groups = "usb2";
function = "usb2";
};
+
+ /*
+ * - On Salvator-X[S], GP6_3[01] are connected to ADV7482 as irq pins
+ * (when SW31 is the default setting on Salvator-XS).
+ * - If SW31 is the default setting, you cannot use USB2.0 ch3 on
+ * r8a7795 with Salvator-XS.
+ * Hence the SW31 setting must be changed like 2) below.
+ * 1) Default setting of SW31: ON-ON-OFF-OFF-OFF-OFF:
+ * - Connect GP6_3[01] to ADV7842.
+ * 2) Changed setting of SW31: OFF-OFF-ON-ON-ON-ON:
+ * - Connect GP6_3[01] to BD082065 (USB2.0 ch3's host power).
+ * - Connect GP6_{04,21} to ADV7842.
+ */
+ usb2_ch3_pins: usb2_ch3 {
+ groups = "usb2_ch3";
+ function = "usb2_ch3";
+ };
};
&usb2_phy2 {
@@ -153,3 +170,10 @@
status = "okay";
};
+
+&usb2_phy3 {
+ pinctrl-0 = <&usb2_ch3_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
--
2.11.0
^ permalink raw reply related
* [PATCH 073/102] arm64: dts: renesas: salvator-common: add eeprom
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Wolfram Sang <wsa+renesas@sang-engineering.com>
Add the EEPROM found on Salvator-X and -XS boards for H3, M3-W, and M3-N
on the IIC_DVFS bus.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/salvator-common.dtsi | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
index 9116f4caa3c6..803220a02f50 100644
--- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi
+++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
@@ -385,6 +385,12 @@
};
};
};
+
+ eeprom at 50 {
+ compatible = "rohm,br24t01", "atmel,24c01";
+ reg = <0x50>;
+ pagesize = <8>;
+ };
};
&ohci0 {
--
2.11.0
^ permalink raw reply related
* [PATCH 072/102] arm64: dts: renesas: condor: add CAN-FD support
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Define the Condor board dependent part of the CAN-FD device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a77980-condor.dts | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a77980-condor.dts b/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
index b8df7604dece..0b93a7d76585 100644
--- a/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
@@ -62,6 +62,16 @@
};
};
+&canfd {
+ pinctrl-0 = <&canfd0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ channel0 {
+ status = "okay";
+ };
+};
+
&extal_clk {
clock-frequency = <16666666>;
};
@@ -89,6 +99,11 @@
function = "avb";
};
+ canfd0_pins: canfd0 {
+ groups = "canfd0_data_a";
+ function = "canfd0";
+ };
+
mmc_pins: mmc {
groups = "mmc_data8", "mmc_ctrl", "mmc_ds";
function = "mmc";
--
2.11.0
^ permalink raw reply related
* [PATCH 071/102] arm64: dts: renesas: r8a77980: add CAN-FD support
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Define the generic R8A77980 part of the CAN-FD device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[simon: consistently use tabs for indentation]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a77980.dtsi | 31 +++++++++++++++++++++++++++++++
1 file changed, 31 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a77980.dtsi b/arch/arm64/boot/dts/renesas/r8a77980.dtsi
index 5c865fcd3986..3a127643d1dc 100644
--- a/arch/arm64/boot/dts/renesas/r8a77980.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77980.dtsi
@@ -38,6 +38,13 @@
};
};
+ /* External CAN clock - to be overridden by boards that provide it */
+ can_clk: can {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+
extal_clk: extal {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -170,6 +177,30 @@
status = "disabled";
};
+ canfd: can at e66c0000 {
+ compatible = "renesas,r8a77980-canfd",
+ "renesas,rcar-gen3-canfd";
+ reg = <0 0xe66c0000 0 0x8000>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 914>,
+ <&cpg CPG_CORE R8A77980_CLK_CANFD>,
+ <&can_clk>;
+ clock-names = "fck", "canfd", "can_clk";
+ assigned-clocks = <&cpg CPG_CORE R8A77980_CLK_CANFD>;
+ assigned-clock-rates = <40000000>;
+ power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
+ status = "disabled";
+
+ channel0 {
+ status = "disabled";
+ };
+
+ channel1 {
+ status = "disabled";
+ };
+ };
+
avb: ethernet at e6800000 {
compatible = "renesas,etheravb-r8a77980",
"renesas,etheravb-rcar-gen3";
--
2.11.0
^ permalink raw reply related
* [PATCH 070/102] arm64: dts: renesas: eagle: add CAN-FD support
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Define the Eagle board dependent part of the CAN-FD device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a77970-eagle.dts | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts b/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts
index b800a119753b..21f9cf5c6e84 100644
--- a/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts
@@ -95,6 +95,16 @@
};
};
+&canfd {
+ pinctrl-0 = <&canfd0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ channel0 {
+ status = "okay";
+ };
+};
+
&extal_clk {
clock-frequency = <16666666>;
};
@@ -156,6 +166,11 @@
function = "avb0";
};
+ canfd0_pins: canfd0 {
+ groups = "canfd0_data_a";
+ function = "canfd0";
+ };
+
i2c0_pins: i2c0 {
groups = "i2c0";
function = "i2c0";
--
2.11.0
^ permalink raw reply related
* [PATCH 069/102] arm64: dts: renesas: r8a77970: add CAN-FD support
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Define the generic R8A77970 part of the CAN-FD device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a77970.dtsi | 32 +++++++++++++++++++++++++++++++
1 file changed, 32 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a77970.dtsi b/arch/arm64/boot/dts/renesas/r8a77970.dtsi
index 6ed2e95eb53d..37b843c0677a 100644
--- a/arch/arm64/boot/dts/renesas/r8a77970.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77970.dtsi
@@ -68,6 +68,13 @@
method = "smc";
};
+ /* External CAN clock - to be overridden by boards that provide it */
+ can_clk: can {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+
/* External SCIF clock - to be overridden by boards that provide it */
scif_clk: scif {
compatible = "fixed-clock";
@@ -381,6 +388,31 @@
status = "disabled";
};
+ canfd: can at e66c0000 {
+ compatible = "renesas,r8a77970-canfd",
+ "renesas,rcar-gen3-canfd";
+ reg = <0 0xe66c0000 0 0x8000>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 914>,
+ <&cpg CPG_CORE R8A77970_CLK_CANFD>,
+ <&can_clk>;
+ clock-names = "fck", "canfd", "can_clk";
+ assigned-clocks = <&cpg CPG_CORE R8A77970_CLK_CANFD>;
+ assigned-clock-rates = <40000000>;
+ power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
+ resets = <&cpg 914>;
+ status = "disabled";
+
+ channel0 {
+ status = "disabled";
+ };
+
+ channel1 {
+ status = "disabled";
+ };
+ };
+
avb: ethernet at e6800000 {
compatible = "renesas,etheravb-r8a77970",
"renesas,etheravb-rcar-gen3";
--
2.11.0
^ permalink raw reply related
* [PATCH 068/102] arm64: dts: renesas: r8a77965: Add R-Car Gen3 thermal support
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Niklas S?derlund <niklas.soderlund+renesas@ragnatech.se>
Based on previous work by Ryo Kataoka <ryo.kataoka.wt@renesas.com>.
Signed-off-by: Niklas S?derlund <niklas.soderlund+renesas@ragnatech.se>
[simon: moved thermal node to preseve ordering of nodes by bus address]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a77965.dtsi | 59 +++++++++++++++++++++++++++++++
1 file changed, 59 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a77965.dtsi b/arch/arm64/boot/dts/renesas/r8a77965.dtsi
index 536fed8eec6a..b93281affd63 100644
--- a/arch/arm64/boot/dts/renesas/r8a77965.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77965.dtsi
@@ -282,6 +282,21 @@
#power-domain-cells = <1>;
};
+ tsc: thermal at e6198000 {
+ compatible = "renesas,r8a77965-thermal";
+ reg = <0 0xe6198000 0 0x100>,
+ <0 0xe61a0000 0 0x100>,
+ <0 0xe61a8000 0 0x100>;
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 522>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
+ resets = <&cpg 522>;
+ #thermal-sensor-cells = <1>;
+ status = "okay";
+ };
+
intc_ex: interrupt-controller at e61c0000 {
compatible = "renesas,intc-ex-r8a77965", "renesas,irqc";
#interrupt-cells = <2>;
@@ -1192,6 +1207,50 @@
<&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
};
+ thermal-zones {
+ sensor_thermal1: sensor-thermal1 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&tsc 0>;
+
+ trips {
+ sensor1_crit: sensor1-crit {
+ temperature = <120000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ sensor_thermal2: sensor-thermal2 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&tsc 1>;
+
+ trips {
+ sensor2_crit: sensor2-crit {
+ temperature = <120000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ sensor_thermal3: sensor-thermal3 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&tsc 2>;
+
+ trips {
+ sensor3_crit: sensor3-crit {
+ temperature = <120000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+
/* External USB clocks - can be overridden by the board */
usb3s0_clk: usb3s0 {
compatible = "fixed-clock";
--
2.11.0
^ permalink raw reply related
* [PATCH 067/102] arm64: dts: renesas: r8a77965: use r8a77965-sysc binding definitions
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Niklas S?derlund <niklas.soderlund+renesas@ragnatech.se>
Replace the hardcoded power domain indices by R8A77965_PD_* symbols.
Signed-off-by: Niklas S?derlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
[simon: dropped hunk to include r8a77965-sysc.h which is already present]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a77965.dtsi | 94 +++++++++++++++----------------
1 file changed, 47 insertions(+), 47 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a77965.dtsi b/arch/arm64/boot/dts/renesas/r8a77965.dtsi
index 7c9555309c0a..536fed8eec6a 100644
--- a/arch/arm64/boot/dts/renesas/r8a77965.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77965.dtsi
@@ -61,7 +61,7 @@
compatible = "arm,cortex-a57", "arm,armv8";
reg = <0x0>;
device_type = "cpu";
- power-domains = <&sysc 0>;
+ power-domains = <&sysc R8A77965_PD_CA57_CPU0>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
@@ -70,14 +70,14 @@
compatible = "arm,cortex-a57","arm,armv8";
reg = <0x1>;
device_type = "cpu";
- power-domains = <&sysc 1>;
+ power-domains = <&sysc R8A77965_PD_CA57_CPU1>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
L2_CA57: cache-controller-0 {
compatible = "cache";
- power-domains = <&sysc 12>;
+ power-domains = <&sysc R8A77965_PD_CA57_SCU>;
cache-unified;
cache-level = <2>;
};
@@ -147,7 +147,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 912>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 912>;
};
@@ -162,7 +162,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 911>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 911>;
};
@@ -177,7 +177,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 910>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 910>;
};
@@ -192,7 +192,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 909>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 909>;
};
@@ -207,7 +207,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 908>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 908>;
};
@@ -222,7 +222,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 907>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 907>;
};
@@ -237,7 +237,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 906>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 906>;
};
@@ -252,7 +252,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 905>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 905>;
};
@@ -294,7 +294,7 @@
GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 407>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 407>;
};
@@ -348,7 +348,7 @@
reg = <0 0xe60b0000 0 0x425>;
interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 926>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 926>;
dmas = <&dmac0 0x11>, <&dmac0 0x10>;
dma-names = "tx", "rx";
@@ -367,7 +367,7 @@
renesas,buswait = <11>;
phys = <&usb2_phy0>;
phy-names = "usb";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 704>;
status = "disabled";
};
@@ -380,7 +380,7 @@
GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "ch0", "ch1";
clocks = <&cpg CPG_MOD 330>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 330>;
#dma-cells = <1>;
dma-channels = <2>;
@@ -394,7 +394,7 @@
GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "ch0", "ch1";
clocks = <&cpg CPG_MOD 331>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 331>;
#dma-cells = <1>;
dma-channels = <2>;
@@ -407,7 +407,7 @@
clocks = <&cpg CPG_MOD 328>, <&usb3s0_clk>,
<&usb_extal_clk>;
clock-names = "usb3-if", "usb3s_clk", "usb_extal";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 328>;
#phy-cells = <0>;
status = "disabled";
@@ -441,7 +441,7 @@
"ch12", "ch13", "ch14", "ch15";
clocks = <&cpg CPG_MOD 219>;
clock-names = "fck";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 219>;
#dma-cells = <1>;
dma-channels = <16>;
@@ -475,7 +475,7 @@
"ch12", "ch13", "ch14", "ch15";
clocks = <&cpg CPG_MOD 218>;
clock-names = "fck";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 218>;
#dma-cells = <1>;
dma-channels = <16>;
@@ -509,7 +509,7 @@
"ch12", "ch13", "ch14", "ch15";
clocks = <&cpg CPG_MOD 217>;
clock-names = "fck";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 217>;
#dma-cells = <1>;
dma-channels = <16>;
@@ -552,7 +552,7 @@
"ch20", "ch21", "ch22", "ch23",
"ch24";
clocks = <&cpg CPG_MOD 812>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 812>;
phy-mode = "rgmii";
#address-cells = <1>;
@@ -566,7 +566,7 @@
#pwm-cells = <2>;
clocks = <&cpg CPG_MOD 523>;
resets = <&cpg 523>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -576,7 +576,7 @@
#pwm-cells = <2>;
clocks = <&cpg CPG_MOD 523>;
resets = <&cpg 523>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -586,7 +586,7 @@
#pwm-cells = <2>;
clocks = <&cpg CPG_MOD 523>;
resets = <&cpg 523>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -596,7 +596,7 @@
#pwm-cells = <2>;
clocks = <&cpg CPG_MOD 523>;
resets = <&cpg 523>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -606,7 +606,7 @@
#pwm-cells = <2>;
clocks = <&cpg CPG_MOD 523>;
resets = <&cpg 523>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -616,7 +616,7 @@
#pwm-cells = <2>;
clocks = <&cpg CPG_MOD 523>;
resets = <&cpg 523>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -626,7 +626,7 @@
#pwm-cells = <2>;
clocks = <&cpg CPG_MOD 523>;
resets = <&cpg 523>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -642,7 +642,7 @@
dmas = <&dmac1 0x51>, <&dmac1 0x50>,
<&dmac2 0x51>, <&dmac2 0x50>;
dma-names = "tx", "rx", "tx", "rx";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 207>;
status = "disabled";
};
@@ -659,7 +659,7 @@
dmas = <&dmac1 0x53>, <&dmac1 0x52>,
<&dmac2 0x53>, <&dmac2 0x52>;
dma-names = "tx", "rx", "tx", "rx";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 206>;
status = "disabled";
};
@@ -673,7 +673,7 @@
<&cpg CPG_CORE 20>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 310>;
status = "disabled";
};
@@ -689,7 +689,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x57>, <&dmac0 0x56>;
dma-names = "tx", "rx";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 204>;
status = "disabled";
};
@@ -705,7 +705,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x59>, <&dmac0 0x58>;
dma-names = "tx", "rx";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 203>;
status = "disabled";
};
@@ -722,7 +722,7 @@
dmas = <&dmac1 0x5b>, <&dmac1 0x5a>,
<&dmac2 0x5b>, <&dmac2 0x5a>;
dma-names = "tx", "rx", "tx", "rx";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 202>;
status = "disabled";
};
@@ -736,7 +736,7 @@
dmas = <&dmac1 0x41>, <&dmac1 0x40>,
<&dmac2 0x41>, <&dmac2 0x40>;
dma-names = "tx", "rx", "tx", "rx";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 211>;
#address-cells = <1>;
#size-cells = <0>;
@@ -752,7 +752,7 @@
dmas = <&dmac1 0x43>, <&dmac1 0x42>,
<&dmac2 0x43>, <&dmac2 0x42>;
dma-names = "tx", "rx", "tx", "rx";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 210>;
#address-cells = <1>;
#size-cells = <0>;
@@ -767,7 +767,7 @@
clocks = <&cpg CPG_MOD 209>;
dmas = <&dmac0 0x45>, <&dmac0 0x44>;
dma-names = "tx", "rx";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 209>;
#address-cells = <1>;
#size-cells = <0>;
@@ -782,7 +782,7 @@
clocks = <&cpg CPG_MOD 208>;
dmas = <&dmac0 0x47>, <&dmac0 0x46>;
dma-names = "tx", "rx";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 208>;
#address-cells = <1>;
#size-cells = <0>;
@@ -873,7 +873,7 @@
reg = <0 0xee000000 0 0xc00>;
interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 328>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 328>;
status = "disabled";
};
@@ -884,7 +884,7 @@
reg = <0 0xee020000 0 0x400>;
interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 328>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 328>;
status = "disabled";
};
@@ -896,7 +896,7 @@
clocks = <&cpg CPG_MOD 703>;
phys = <&usb2_phy0>;
phy-names = "usb";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 703>;
status = "disabled";
};
@@ -908,7 +908,7 @@
clocks = <&cpg CPG_MOD 702>;
phys = <&usb2_phy1>;
phy-names = "usb";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 702>;
status = "disabled";
};
@@ -921,7 +921,7 @@
phys = <&usb2_phy0>;
phy-names = "usb";
companion = <&ohci0>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 703>;
status = "disabled";
};
@@ -934,7 +934,7 @@
phys = <&usb2_phy1>;
phy-names = "usb";
companion = <&ohci1>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 702>;
status = "disabled";
};
@@ -945,7 +945,7 @@
reg = <0 0xee080200 0 0x700>;
interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 703>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 703>;
#phy-cells = <0>;
status = "disabled";
@@ -956,7 +956,7 @@
"renesas,rcar-gen3-usb2-phy";
reg = <0 0xee0a0200 0 0x700>;
clocks = <&cpg CPG_MOD 703>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 703>;
#phy-cells = <0>;
status = "disabled";
@@ -995,7 +995,7 @@
(GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
clocks = <&cpg CPG_MOD 408>;
clock-names = "clk";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
resets = <&cpg 408>;
};
--
2.11.0
^ permalink raw reply related
* [PATCH 066/102] arm64: dts: renesas: r8a77980: use SYSC power domain macros
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Now that the commit 7755b40d07a8 ("dt-bindings: power: add R8A77980 SYSC
power domain definitions") has hit Linus' tree, we can replace the bare
numbers (we had to use to avoid a cross tree dependency) with these macro
definitions...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a77980.dtsi | 31 ++++++++++++++++---------------
1 file changed, 16 insertions(+), 15 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a77980.dtsi b/arch/arm64/boot/dts/renesas/r8a77980.dtsi
index fddbaf250087..5c865fcd3986 100644
--- a/arch/arm64/boot/dts/renesas/r8a77980.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77980.dtsi
@@ -9,6 +9,7 @@
#include <dt-bindings/clock/r8a77980-cpg-mssr.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/r8a77980-sysc.h>
/ {
compatible = "renesas,r8a77980";
@@ -24,14 +25,14 @@
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0>;
clocks = <&cpg CPG_CORE R8A77980_CLK_Z2>;
- power-domains = <&sysc 5>;
+ power-domains = <&sysc R8A77980_PD_CA53_CPU0>;
next-level-cache = <&L2_CA53>;
enable-method = "psci";
};
L2_CA53: cache-controller {
compatible = "cache";
- power-domains = <&sysc 21>;
+ power-domains = <&sysc R8A77980_PD_CA53_SCU>;
cache-unified;
cache-level = <2>;
};
@@ -110,7 +111,7 @@
dmas = <&dmac1 0x31>, <&dmac1 0x30>,
<&dmac2 0x31>, <&dmac2 0x30>;
dma-names = "tx", "rx", "tx", "rx";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
resets = <&cpg 520>;
status = "disabled";
};
@@ -128,7 +129,7 @@
dmas = <&dmac1 0x33>, <&dmac1 0x32>,
<&dmac2 0x33>, <&dmac2 0x32>;
dma-names = "tx", "rx", "tx", "rx";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
resets = <&cpg 519>;
status = "disabled";
};
@@ -146,7 +147,7 @@
dmas = <&dmac1 0x35>, <&dmac1 0x34>,
<&dmac2 0x35>, <&dmac2 0x34>;
dma-names = "tx", "rx", "tx", "rx";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
resets = <&cpg 518>;
status = "disabled";
};
@@ -164,7 +165,7 @@
dmas = <&dmac1 0x37>, <&dmac1 0x36>,
<&dmac2 0x37>, <&dmac2 0x36>;
dma-names = "tx", "rx", "tx", "rx";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
resets = <&cpg 517>;
status = "disabled";
};
@@ -206,7 +207,7 @@
"ch20", "ch21", "ch22", "ch23",
"ch24";
clocks = <&cpg CPG_MOD 812>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
resets = <&cpg 812>;
phy-mode = "rgmii";
#address-cells = <1>;
@@ -226,7 +227,7 @@
dmas = <&dmac1 0x51>, <&dmac1 0x50>,
<&dmac2 0x51>, <&dmac2 0x50>;
dma-names = "tx", "rx", "tx", "rx";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
resets = <&cpg 207>;
status = "disabled";
};
@@ -244,7 +245,7 @@
dmas = <&dmac1 0x53>, <&dmac1 0x52>,
<&dmac2 0x53>, <&dmac2 0x52>;
dma-names = "tx", "rx", "tx", "rx";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
resets = <&cpg 206>;
status = "disabled";
};
@@ -262,7 +263,7 @@
dmas = <&dmac1 0x57>, <&dmac1 0x56>,
<&dmac2 0x57>, <&dmac2 0x56>;
dma-names = "tx", "rx", "tx", "rx";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
resets = <&cpg 204>;
status = "disabled";
};
@@ -280,7 +281,7 @@
dmas = <&dmac1 0x59>, <&dmac1 0x58>,
<&dmac2 0x59>, <&dmac2 0x58>;
dma-names = "tx", "rx", "tx", "rx";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
resets = <&cpg 203>;
status = "disabled";
};
@@ -313,7 +314,7 @@
"ch12", "ch13", "ch14", "ch15";
clocks = <&cpg CPG_MOD 218>;
clock-names = "fck";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
resets = <&cpg 218>;
#dma-cells = <1>;
dma-channels = <16>;
@@ -347,7 +348,7 @@
"ch12", "ch13", "ch14", "ch15";
clocks = <&cpg CPG_MOD 217>;
clock-names = "fck";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
resets = <&cpg 217>;
#dma-cells = <1>;
dma-channels = <16>;
@@ -359,7 +360,7 @@
reg = <0 0xee140000 0 0x2000>;
interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 314>;
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
resets = <&cpg 314>;
max-frequency = <200000000>;
status = "disabled";
@@ -378,7 +379,7 @@
IRQ_TYPE_LEVEL_HIGH)>;
clocks = <&cpg CPG_MOD 408>;
clock-names = "clk";
- power-domains = <&sysc 32>;
+ power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
resets = <&cpg 408>;
};
--
2.11.0
^ permalink raw reply related
* [PATCH 065/102] arm64: dts: renesas: r8a77980: use CPG core clock macros
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Now that the commit 35b3c462dae1 ("dt-bindings: clock: add R8A77980 CPG
core clock definitions") has hit Linus' tree, we can replace the bare
numbers (we had to use to avoid a cross tree dependency) with these macro
definitions...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a77980.dtsi | 20 ++++++++++----------
1 file changed, 10 insertions(+), 10 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a77980.dtsi b/arch/arm64/boot/dts/renesas/r8a77980.dtsi
index d27b80bcdbb4..fddbaf250087 100644
--- a/arch/arm64/boot/dts/renesas/r8a77980.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77980.dtsi
@@ -6,9 +6,9 @@
* Copyright (C) 2018 Cogent Embedded, Inc.
*/
+#include <dt-bindings/clock/r8a77980-cpg-mssr.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/clock/renesas-cpg-mssr.h>
/ {
compatible = "renesas,r8a77980";
@@ -23,7 +23,7 @@
device_type = "cpu";
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0>;
- clocks = <&cpg CPG_CORE 0>;
+ clocks = <&cpg CPG_CORE R8A77980_CLK_Z2>;
power-domains = <&sysc 5>;
next-level-cache = <&L2_CA53>;
enable-method = "psci";
@@ -104,7 +104,7 @@
reg = <0 0xe6540000 0 0x60>;
interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 520>,
- <&cpg CPG_CORE 19>,
+ <&cpg CPG_CORE R8A77980_CLK_S3D1>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x31>, <&dmac1 0x30>,
@@ -122,7 +122,7 @@
reg = <0 0xe6550000 0 0x60>;
interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 519>,
- <&cpg CPG_CORE 19>,
+ <&cpg CPG_CORE R8A77980_CLK_S3D1>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x33>, <&dmac1 0x32>,
@@ -140,7 +140,7 @@
reg = <0 0xe6560000 0 0x60>;
interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 518>,
- <&cpg CPG_CORE 19>,
+ <&cpg CPG_CORE R8A77980_CLK_S3D1>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x35>, <&dmac1 0x34>,
@@ -158,7 +158,7 @@
reg = <0 0xe66a0000 0 0x60>;
interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 517>,
- <&cpg CPG_CORE 19>,
+ <&cpg CPG_CORE R8A77980_CLK_S3D1>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x37>, <&dmac1 0x36>,
@@ -220,7 +220,7 @@
reg = <0 0xe6e60000 0 0x40>;
interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 207>,
- <&cpg CPG_CORE 19>,
+ <&cpg CPG_CORE R8A77980_CLK_S3D1>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x51>, <&dmac1 0x50>,
@@ -238,7 +238,7 @@
reg = <0 0xe6e68000 0 0x40>;
interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 206>,
- <&cpg CPG_CORE 19>,
+ <&cpg CPG_CORE R8A77980_CLK_S3D1>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x53>, <&dmac1 0x52>,
@@ -256,7 +256,7 @@
reg = <0 0xe6c50000 0 0x40>;
interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 204>,
- <&cpg CPG_CORE 19>,
+ <&cpg CPG_CORE R8A77980_CLK_S3D1>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x57>, <&dmac1 0x56>,
@@ -274,7 +274,7 @@
reg = <0 0xe6c40000 0 0x40>;
interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 203>,
- <&cpg CPG_CORE 19>,
+ <&cpg CPG_CORE R8A77980_CLK_S3D1>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x59>, <&dmac1 0x58>,
--
2.11.0
^ permalink raw reply related
* [PATCH 064/102] arm64: dts: renesas: r8a77965: Add address properties to rcar_sound port nodes
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
The rcar_sound port nodes have unit names and thus should have register
properties.
This is flagged by dtc as follows:
# make dtbs W=1
...
DTC arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound at ec500000/ports/port at 0: node has a unit name, but no reg property
DTC arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dtb
arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound at ec500000/ports/port at 0: node has a unit name, but no reg property
Prior to this patch the port nodes only defined in board DTS files.
As the register properties are common this patch defines the port nodes
and provides register properties in the SoC DTS file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas S?derlund <niklas.soderlund+renesas@ragnatech.se>
---
arch/arm64/boot/dts/renesas/r8a77965.dtsi | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a77965.dtsi b/arch/arm64/boot/dts/renesas/r8a77965.dtsi
index b46af2744135..7c9555309c0a 100644
--- a/arch/arm64/boot/dts/renesas/r8a77965.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77965.dtsi
@@ -857,6 +857,14 @@
ssi1: ssi-1 {
};
};
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port at 0 {
+ reg = <0>;
+ };
+ };
};
xhci0: usb at ee000000 {
--
2.11.0
^ permalink raw reply related
* [PATCH 063/102] arm64: dts: renesas: r8a7796: Add address properties to rcar_sound port nodes
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
The rcar_sound port nodes have unit names and thus should have register
properties.
This is flagged by dtc as follows:
# make dtbs W=1
...
DTC arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound at ec500000/ports/port at 0: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound at ec500000/ports/port at 1: node has a unit name, but no reg property
...
DTC arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound at ec500000/ports/port at 0: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound at ec500000/ports/port at 1: node has a unit name, but no reg property
Prior to this patch the port nodes only defined in board DTS files.
As the register properties are common this patch defines the port nodes
and provides register properties in the SoC DTS file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas S?derlund <niklas.soderlund+renesas@ragnatech.se>
---
arch/arm64/boot/dts/renesas/r8a7796.dtsi | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index f41bc25b3933..3fbd86590fb0 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -1594,6 +1594,17 @@
dma-names = "rx", "tx", "rxu", "txu";
};
};
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port at 0 {
+ reg = <0>;
+ };
+ port at 1 {
+ reg = <1>;
+ };
+ };
};
audma0: dma-controller at ec700000 {
--
2.11.0
^ permalink raw reply related
* [PATCH 062/102] arm64: dts: renesas: r8a7795: Add address properties to rcar_sound port nodes
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
The rcar_sound port nodes have unit names and thus should have register
properties.
This is flagged by dtc as follows:
# make dtbs W=1
...
DTC arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound at ec500000/ports/port at 0: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound at ec500000/ports/port at 1: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound at ec500000/ports/port at 2: node has a unit name, but no reg property
...
DTC arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb
arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound at ec500000/ports/port at 0: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound at ec500000/ports/port at 1: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound at ec500000/ports/port at 2: node has a unit name, but no reg property
DTC arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound at ec500000/ports/port at 0: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound at ec500000/ports/port at 1: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound at ec500000/ports/port at 2: node has a unit name, but no reg property
Prior to this patch the port nodes only defined in board DTS files.
As the register properties are common this patch defines the port nodes
and provides register properties in the SoC DTS file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas S?derlund <niklas.soderlund+renesas@ragnatech.se>
---
arch/arm64/boot/dts/renesas/r8a7795.dtsi | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
index b1c52dae4d49..9b080a864ea1 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
@@ -1711,6 +1711,20 @@
dma-names = "rx", "tx", "rxu", "txu";
};
};
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port at 0 {
+ reg = <0>;
+ };
+ port at 1 {
+ reg = <1>;
+ };
+ port at 2 {
+ reg = <2>;
+ };
+ };
};
audma0: dma-controller at ec700000 {
--
2.11.0
^ permalink raw reply related
* [PATCH 061/102] arm64: dts: renesas: v3msk: add DU/LVDS/HDMI support
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Define the V3M Starter Kit board dependent part of the DU and LVDS device
nodes. Also add the device nodes for Thine THC63LVD1024 LVDS decoder and
Analog Devices ADV7511W HDMI transmitter...
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a77970-v3msk.dts | 129 +++++++++++++++++++++++++
1 file changed, 129 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a77970-v3msk.dts b/arch/arm64/boot/dts/renesas/r8a77970-v3msk.dts
index 55aa01b663e5..9fce031a596f 100644
--- a/arch/arm64/boot/dts/renesas/r8a77970-v3msk.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77970-v3msk.dts
@@ -29,6 +29,65 @@
/* first 128MB is reserved for secure area. */
reg = <0x0 0x48000000 0x0 0x38000000>;
};
+
+ osc5_clk: osc5-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <148500000>;
+ };
+
+ vcc_d1_8v: regulator-0 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_D1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vcc_d3_3v: regulator-1 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_D3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ lvds-decoder {
+ compatible = "thine,thc63lvd1024";
+ vcc-supply = <&vcc_d3_3v>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ thc63lvd1024_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+
+ port at 2 {
+ reg = <2>;
+ thc63lvd1024_out: endpoint {
+ remote-endpoint = <&adv7511_in>;
+ };
+ };
+ };
+ };
+
+ hdmi-out {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con: endpoint {
+ remote-endpoint = <&adv7511_out>;
+ };
+ };
+ };
};
&avb {
@@ -46,6 +105,13 @@
};
};
+&du {
+ clocks = <&cpg CPG_MOD 724>,
+ <&osc5_clk>;
+ clock-names = "du.0", "dclkin.0";
+ status = "okay";
+};
+
&extal_clk {
clock-frequency = <16666666>;
};
@@ -60,12 +126,75 @@
function = "avb0";
};
+ i2c0_pins: i2c0 {
+ groups = "i2c0";
+ function = "i2c0";
+ };
+
scif0_pins: scif0 {
groups = "scif0_data";
function = "scif0";
};
};
+&i2c0 {
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+ clock-frequency = <400000>;
+
+ hdmi at 39{
+ compatible = "adi,adv7511w";
+ #sound-dai-cells = <0>;
+ reg = <0x39>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
+ avdd-supply = <&vcc_d1_8v>;
+ dvdd-supply = <&vcc_d1_8v>;
+ pvdd-supply = <&vcc_d1_8v>;
+ bgvdd-supply = <&vcc_d1_8v>;
+ dvdd-3v-supply = <&vcc_d3_3v>;
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "rgb";
+ adi,input-clock = "1x";
+ adi,input-style = <1>;
+ adi,input-justification = "evenly";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ adv7511_in: endpoint {
+ remote-endpoint = <&thc63lvd1024_out>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+ adv7511_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+};
+
+&lvds0 {
+ status = "okay";
+
+ ports {
+ port at 1 {
+ lvds0_out: endpoint {
+ remote-endpoint = <&thc63lvd1024_in>;
+ };
+ };
+ };
+};
+
&scif0 {
pinctrl-0 = <&scif0_pins>;
pinctrl-names = "default";
--
2.11.0
^ permalink raw reply related
* [PATCH 060/102] arm64: dts: renesas: condor: add eMMC support
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Define the Condor board dependent part of the MMC0 (connected to eMMC chip)
device node along with the necessary voltage regulators...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a77980-condor.dts | 43 +++++++++++++++++++++++++
1 file changed, 43 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a77980-condor.dts b/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
index 7af5afa41795..b8df7604dece 100644
--- a/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
@@ -27,6 +27,24 @@
/* first 128MB is reserved for secure area. */
reg = <0 0x48000000 0 0x78000000>;
};
+
+ d3_3v: regulator-0 {
+ compatible = "regulator-fixed";
+ regulator-name = "D3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vddq_vin01: regulator-1 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDQ_VIN01";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
};
&avb {
@@ -52,12 +70,37 @@
clock-frequency = <32768>;
};
+&mmc0 {
+ pinctrl-0 = <&mmc_pins>;
+ pinctrl-1 = <&mmc_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <&d3_3v>;
+ vqmmc-supply = <&vddq_vin01>;
+ mmc-hs200-1_8v;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
&pfc {
avb_pins: avb {
groups = "avb_mdio", "avb_rgmii";
function = "avb";
};
+ mmc_pins: mmc {
+ groups = "mmc_data8", "mmc_ctrl", "mmc_ds";
+ function = "mmc";
+ power-source = <3300>;
+ };
+
+ mmc_pins_uhs: mmc_uhs {
+ groups = "mmc_data8", "mmc_ctrl", "mmc_ds";
+ function = "mmc";
+ power-source = <1800>;
+ };
+
scif0_pins: scif0 {
groups = "scif0_data";
function = "scif0";
--
2.11.0
^ permalink raw reply related
* [PATCH 059/102] arm64: dts: renesas: r8a77965-salvator-xs: Enable DU external clocks and HDMI
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The DU1 external dot clock is provided by the fixed frequency clock
generator X21, while the DU0 and DU3 clocks are provided by the
programmable Versaclock6 clock generator.
Enable the clocks, and the HDMI encoder for the M3-N Salvator-XS, and
hook it up to the HDMI connector
Based on patches from Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
.../boot/dts/renesas/r8a77965-salvator-xs.dts | 28 ++++++++++++++++++++++
1 file changed, 28 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dts b/arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dts
index a83a00deed9e..9de4e3db1621 100644
--- a/arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dts
@@ -19,3 +19,31 @@
reg = <0x0 0x48000000 0x0 0x78000000>;
};
};
+
+&du {
+ clocks = <&cpg CPG_MOD 724>,
+ <&cpg CPG_MOD 723>,
+ <&cpg CPG_MOD 721>,
+ <&versaclock6 1>,
+ <&x21_clk>,
+ <&versaclock6 2>;
+ clock-names = "du.0", "du.1", "du.3",
+ "dclkin.0", "dclkin.1", "dclkin.3";
+};
+
+&hdmi0 {
+ status = "okay";
+
+ ports {
+ port at 1 {
+ reg = <1>;
+ rcar_dw_hdmi0_out: endpoint {
+ remote-endpoint = <&hdmi0_con>;
+ };
+ };
+ };
+};
+
+&hdmi0_con {
+ remote-endpoint = <&rcar_dw_hdmi0_out>;
+};
--
2.11.0
^ permalink raw reply related
* [PATCH 058/102] arm64: dts: renesas: r8a77965-salvator-x: Enable DU external clocks and HDMI
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The DU1 external dot clock is provided by the fixed frequency clock
generator X21, while the DU0 and DU3 clocks are provided by the
programmable Versaclock5 clock generator.
Enable the clocks, and the HDMI encoder for the M3-N Salvator-X board
and hook it up to the HDMI connector.
Based on patches from Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
.../arm64/boot/dts/renesas/r8a77965-salvator-x.dts | 28 ++++++++++++++++++++++
1 file changed, 28 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dts
index 75d890d91df9..340a3c72b65a 100644
--- a/arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dts
@@ -19,3 +19,31 @@
reg = <0x0 0x48000000 0x0 0x78000000>;
};
};
+
+&du {
+ clocks = <&cpg CPG_MOD 724>,
+ <&cpg CPG_MOD 723>,
+ <&cpg CPG_MOD 721>,
+ <&versaclock5 1>,
+ <&x21_clk>,
+ <&versaclock5 2>;
+ clock-names = "du.0", "du.1", "du.3",
+ "dclkin.0", "dclkin.1", "dclkin.3";
+};
+
+&hdmi0 {
+ status = "okay";
+
+ ports {
+ port at 1 {
+ reg = <1>;
+ rcar_dw_hdmi0_out: endpoint {
+ remote-endpoint = <&hdmi0_con>;
+ };
+ };
+ };
+};
+
+&hdmi0_con {
+ remote-endpoint = <&rcar_dw_hdmi0_out>;
+};
--
2.11.0
^ permalink raw reply related
* [PATCH 057/102] arm64: dts: renesas: r8a77965: Add HDMI encoder instance
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Add the HDMI encoder to the R8A77965 DT in disabled state.
Based on a similar patch of the R8A7796 device tree
by Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Kieran: Rebase to top of tree]
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a77965.dtsi | 30 +++++++++++++++++++++++++++++-
1 file changed, 29 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a77965.dtsi b/arch/arm64/boot/dts/renesas/r8a77965.dtsi
index a35ea2f32da2..b46af2744135 100644
--- a/arch/arm64/boot/dts/renesas/r8a77965.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77965.dtsi
@@ -8,7 +8,7 @@
* Copyright (C) 2016 Renesas Electronics Corp.
*/
-#include <dt-bindings/clock/renesas-cpg-mssr.h>
+#include <dt-bindings/clock/r8a77965-cpg-mssr.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/power/r8a77965-sysc.h>
@@ -1105,6 +1105,33 @@
};
};
+ hdmi0: hdmi at fead0000 {
+ compatible = "renesas,r8a77965-hdmi",
+ "renesas,rcar-gen3-hdmi";
+ reg = <0 0xfead0000 0 0x10000>;
+ interrupts = <GIC_SPI 389 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 729>,
+ <&cpg CPG_CORE R8A77965_CLK_HDMI>;
+ clock-names = "iahb", "isfr";
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
+ resets = <&cpg 729>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port at 0 {
+ reg = <0>;
+ dw_hdmi0_in: endpoint {
+ remote-endpoint = <&du_out_hdmi0>;
+ };
+ };
+ port at 1 {
+ reg = <1>;
+ };
+ };
+ };
+
du: display at feb00000 {
compatible = "renesas,du-r8a77965";
reg = <0 0xfeb00000 0 0x80000>;
@@ -1132,6 +1159,7 @@
port at 1 {
reg = <1>;
du_out_hdmi0: endpoint {
+ remote-endpoint = <&dw_hdmi0_in>;
};
};
port at 2 {
--
2.11.0
^ permalink raw reply related
* [PATCH 056/102] arm64: dts: renesas: r8a77965: Populate the DU instance placeholder
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The DU entity node has been previously added but only as a placeholder.
Populate the node with the properties to use the device.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a77965.dtsi | 16 +++++++++++++---
1 file changed, 13 insertions(+), 3 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a77965.dtsi b/arch/arm64/boot/dts/renesas/r8a77965.dtsi
index 362eddc6b3d1..a35ea2f32da2 100644
--- a/arch/arm64/boot/dts/renesas/r8a77965.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77965.dtsi
@@ -1106,9 +1106,19 @@
};
du: display at feb00000 {
- reg = <0 0xfeb00000 0 0x80000>,
- <0 0xfeb90000 0 0x14>;
- /* placeholder */
+ compatible = "renesas,du-r8a77965";
+ reg = <0 0xfeb00000 0 0x80000>;
+ reg-names = "du";
+ interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 724>,
+ <&cpg CPG_MOD 723>,
+ <&cpg CPG_MOD 721>;
+ clock-names = "du.0", "du.1", "du.3";
+ status = "disabled";
+
+ vsps = <&vspd0 0 &vspd1 0 &vspd0 1>;
ports {
#address-cells = <1>;
--
2.11.0
^ permalink raw reply related
* [PATCH 055/102] arm64: dts: renesas: r8a77965: Add VSP instances
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The r8a77965 has 4 VSP instances.
Based on a similar patch of the R8A7796 device tree
by Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Kieran: Rebased to top of tree, fixed sort orders]
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a77965.dtsi | 44 +++++++++++++++++++++++++++++++
1 file changed, 44 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a77965.dtsi b/arch/arm64/boot/dts/renesas/r8a77965.dtsi
index 74a7ae4ebccc..362eddc6b3d1 100644
--- a/arch/arm64/boot/dts/renesas/r8a77965.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77965.dtsi
@@ -1009,6 +1009,17 @@
resets = <&cpg 615>;
};
+ vspb: vsp at fe960000 {
+ compatible = "renesas,vsp2";
+ reg = <0 0xfe960000 0 0x8000>;
+ interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 626>;
+ power-domains = <&sysc R8A77965_PD_A3VP>;
+ resets = <&cpg 626>;
+
+ renesas,fcp = <&fcpvb0>;
+ };
+
fcpvb0: fcp at fe96f000 {
compatible = "renesas,fcpv";
reg = <0 0xfe96f000 0 0x200>;
@@ -1017,6 +1028,17 @@
resets = <&cpg 607>;
};
+ vspi0: vsp at fe9a0000 {
+ compatible = "renesas,vsp2";
+ reg = <0 0xfe9a0000 0 0x8000>;
+ interrupts = <GIC_SPI 444 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 631>;
+ power-domains = <&sysc R8A77965_PD_A3VP>;
+ resets = <&cpg 631>;
+
+ renesas,fcp = <&fcpvi0>;
+ };
+
fcpvi0: fcp at fe9af000 {
compatible = "renesas,fcpv";
reg = <0 0xfe9af000 0 0x200>;
@@ -1025,6 +1047,17 @@
resets = <&cpg 611>;
};
+ vspd0: vsp at fea20000 {
+ compatible = "renesas,vsp2";
+ reg = <0 0xfea20000 0 0x8000>;
+ interrupts = <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 623>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
+ resets = <&cpg 623>;
+
+ renesas,fcp = <&fcpvd0>;
+ };
+
fcpvd0: fcp at fea27000 {
compatible = "renesas,fcpv";
reg = <0 0xfea27000 0 0x200>;
@@ -1033,6 +1066,17 @@
resets = <&cpg 603>;
};
+ vspd1: vsp at fea28000 {
+ compatible = "renesas,vsp2";
+ reg = <0 0xfea28000 0 0x8000>;
+ interrupts = <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 622>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
+ resets = <&cpg 622>;
+
+ renesas,fcp = <&fcpvd1>;
+ };
+
fcpvd1: fcp at fea2f000 {
compatible = "renesas,fcpv";
reg = <0 0xfea2f000 0 0x200>;
--
2.11.0
^ permalink raw reply related
* [PATCH 054/102] arm64: dts: renesas: r8a77965: Add FCPF and FCPV instances
From: Simon Horman @ 2018-05-18 11:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1526637994.git.horms+renesas@verge.net.au>
From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The FCPs handle the interface between various IP cores and memory. Add
the instances related to the FDPs and VSP2s.
Based on a similar patch of the R8A7796 device tree
by Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Kieran: Rebase to top of tree]
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a77965.dtsi | 41 +++++++++++++++++++++++++++++++
1 file changed, 41 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a77965.dtsi b/arch/arm64/boot/dts/renesas/r8a77965.dtsi
index b12f41755aea..74a7ae4ebccc 100644
--- a/arch/arm64/boot/dts/renesas/r8a77965.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77965.dtsi
@@ -10,6 +10,7 @@
#include <dt-bindings/clock/renesas-cpg-mssr.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/r8a77965-sysc.h>
#define CPG_AUDIO_CLK_I 10
@@ -1000,6 +1001,46 @@
/* placeholder */
};
+ fcpf0: fcp at fe950000 {
+ compatible = "renesas,fcpf";
+ reg = <0 0xfe950000 0 0x200>;
+ clocks = <&cpg CPG_MOD 615>;
+ power-domains = <&sysc R8A77965_PD_A3VP>;
+ resets = <&cpg 615>;
+ };
+
+ fcpvb0: fcp at fe96f000 {
+ compatible = "renesas,fcpv";
+ reg = <0 0xfe96f000 0 0x200>;
+ clocks = <&cpg CPG_MOD 607>;
+ power-domains = <&sysc R8A77965_PD_A3VP>;
+ resets = <&cpg 607>;
+ };
+
+ fcpvi0: fcp at fe9af000 {
+ compatible = "renesas,fcpv";
+ reg = <0 0xfe9af000 0 0x200>;
+ clocks = <&cpg CPG_MOD 611>;
+ power-domains = <&sysc R8A77965_PD_A3VP>;
+ resets = <&cpg 611>;
+ };
+
+ fcpvd0: fcp at fea27000 {
+ compatible = "renesas,fcpv";
+ reg = <0 0xfea27000 0 0x200>;
+ clocks = <&cpg CPG_MOD 603>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
+ resets = <&cpg 603>;
+ };
+
+ fcpvd1: fcp at fea2f000 {
+ compatible = "renesas,fcpv";
+ reg = <0 0xfea2f000 0 0x200>;
+ clocks = <&cpg CPG_MOD 602>;
+ power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
+ resets = <&cpg 602>;
+ };
+
csi20: csi2 at fea80000 {
reg = <0 0xfea80000 0 0x10000>;
/* placeholder */
--
2.11.0
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox