* Re: [PATCH v2 1/3] dt-bindings: soc: imx: fsl,imx93-media-blk-ctrl: Allow LVDS Display Bridge child node
From: Liu Ying @ 2026-06-10 7:56 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Frank Li,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, Peng Fan,
devicetree, imx, linux-arm-kernel, linux-kernel, Marco Felsch
In-Reply-To: <20260610-large-just-lynx-d8cb7f@quoll>
On Wed, Jun 10, 2026 at 09:46:39AM +0200, Krzysztof Kozlowski wrote:
> On Mon, Jun 08, 2026 at 05:04:22PM +0800, Liu Ying wrote:
> > i.MX93 SoC mediamix blk-ctrl contains one LDB_CTRL register and one LVDS
> > register which control video output through a LVDS interface. Allow the
> > LVDS Display Bridge(LDB) child node and add the child node to example.
> >
> > Signed-off-by: Liu Ying <victor.liu@nxp.com>
> > ---
> > .../bindings/soc/imx/fsl,imx93-media-blk-ctrl.yaml | 39 ++++++++++++++++++++++
> > 1 file changed, 39 insertions(+)
> >
> > diff --git a/Documentation/devicetree/bindings/soc/imx/fsl,imx93-media-blk-ctrl.yaml b/Documentation/devicetree/bindings/soc/imx/fsl,imx93-media-blk-ctrl.yaml
> > index d828c2e82965..124f5c206ee3 100644
> > --- a/Documentation/devicetree/bindings/soc/imx/fsl,imx93-media-blk-ctrl.yaml
> > +++ b/Documentation/devicetree/bindings/soc/imx/fsl,imx93-media-blk-ctrl.yaml
> > @@ -26,6 +26,12 @@ properties:
> > reg:
> > maxItems: 1
> >
> > + '#address-cells':
> > + const: 1
> > +
> > + '#size-cells':
> > + const: 1
> > +
> > '#power-domain-cells':
> > const: 1
> >
> > @@ -92,6 +98,11 @@ properties:
> > - compatible
> > - ports
> >
> > + bridge@20:
>
> You have dpi-bridge, so this should not be different. You should not mix
> addressable and non-addressable nodes and NXP decided recently in
> 3feaa4342637eef673243dd38ccb32e8dc8efd5a that everything will be
> non-addressable.
>
> Writing bindings ask explicitly to post bindings, so if you decide to do
> half-baked solutions it's on you. Half baked solutions are not allowing
> to bypass standard rules.
Mixing addressable and non-addressable nodes is allowed according to recent
discussion[1].
[1] https://lore.kernel.org/all/n6akxiayi3g6gxcqhreb4iaohmeokoalnqup6h5r2fwdt4zijt@u2wyps55ayqm/
>
> Best regards,
> Krzysztof
>
--
Regards,
Liu Ying
^ permalink raw reply
* [PATCH v3 3/5] dt-bindings: clock: cix,sky1-audss-clock: add audss clock controller
From: joakim.zhang @ 2026-06-10 7:56 UTC (permalink / raw)
To: mturquette, sboyd, bmasney, robh, krzk+dt, conor+dt, p.zabel,
gary.yang
Cc: cix-kernel-upstream, linux-clk, devicetree, linux-kernel,
linux-arm-kernel, Joakim Zhang
In-Reply-To: <20260610075645.3581145-1-joakim.zhang@cixtech.com>
From: Joakim Zhang <joakim.zhang@cixtech.com>
The AUDSS CRU contains an internal clock tree of muxes, dividers and
gates for DSP, I2S, HDA, DMAC and related blocks. The clock provider is
a child node of the cix,sky1-audss-system-control syscon and accesses
registers through the parent MMIO region.
Add the devicetree binding for cix,sky1-audss-clock and clock indices in
include/dt-bindings/clock/cix,sky1-audss.h. Document the parent syscon
indices.
Signed-off-by: Joakim Zhang <joakim.zhang@cixtech.com>
---
.../bindings/clock/cix,sky1-audss-clock.yaml | 80 +++++++++++++++++++
include/dt-bindings/clock/cix,sky1-audss.h | 60 ++++++++++++++
2 files changed, 140 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/cix,sky1-audss-clock.yaml
create mode 100644 include/dt-bindings/clock/cix,sky1-audss.h
diff --git a/Documentation/devicetree/bindings/clock/cix,sky1-audss-clock.yaml b/Documentation/devicetree/bindings/clock/cix,sky1-audss-clock.yaml
new file mode 100644
index 000000000000..dff56f3a425b
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/cix,sky1-audss-clock.yaml
@@ -0,0 +1,80 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/cix,sky1-audss-clock.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cix Sky1 audio subsystem clock controller
+
+maintainers:
+ - Joakim Zhang <joakim.zhang@cixtech.com>
+
+description: |
+ Clock provider for the Cix Sky1 audio subsystem (AUDSS).
+
+ This node is a child of a cix,sky1-audss-system-control MFD/syscon node
+ (see cix,sky1-system-control.yaml). It does not have a reg property; clock
+ mux, divider and gate fields are accessed through the parent register block.
+
+ Software reset lines for AUDSS blocks are exposed on the parent syscon via
+ #reset-cells. Reset indices are defined in
+ include/dt-bindings/reset/cix,sky1-audss-system-control.h.
+
+ Four SoC-level reference clocks listed in clocks/clock-names feed the AUDSS
+ clock tree. The provider exposes the internal AUDSS clocks to other devices
+ via #clock-cells; indices are defined in cix,sky1-audss.h.
+
+properties:
+ compatible:
+ const: cix,sky1-audss-clock
+
+ '#clock-cells':
+ const: 1
+ description:
+ Clock indices are defined in include/dt-bindings/clock/cix,sky1-audss.h.
+
+ clocks:
+ items:
+ - description: I2S parent clock for sampling rates multiple of 8kHz.
+ - description: I2S parent clock for sampling rates multiple of 11.025kHz.
+ - description: clock feeding most devices in audss (NOC, DSP, SRAM, HDA, DMAC, I2S, and Mailbox).
+ - description: clock feeding for HDA, Timer and Watchdog, which is a delicated 48MHz clock.
+
+ clock-names:
+ items:
+ - const: x8k
+ - const: x11k
+ - const: sys
+ - const: 48m
+
+ resets:
+ maxItems: 1
+ description: Audio subsystem NoC (or bus) reset line.
+
+ power-domains:
+ maxItems: 1
+ description: Audio subsystem power domain.
+
+required:
+ - compatible
+ - '#clock-cells'
+ - clocks
+ - clock-names
+ - resets
+ - power-domains
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/cix,sky1.h>
+
+ clock-controller {
+ compatible = "cix,sky1-audss-clock";
+ power-domains = <&smc_devpd 0>;
+ #clock-cells = <1>;
+ clocks = <&scmi_clk CLK_TREE_AUDIO_CLK0>, <&scmi_clk CLK_TREE_AUDIO_CLK2>,
+ <&scmi_clk CLK_TREE_AUDIO_CLK4>, <&scmi_clk CLK_TREE_AUDIO_CLK5>;
+ clock-names = "x8k", "x11k", "sys", "48m";
+ resets = <&s5_syscon 31>;
+ };
diff --git a/include/dt-bindings/clock/cix,sky1-audss.h b/include/dt-bindings/clock/cix,sky1-audss.h
new file mode 100644
index 000000000000..033046407dee
--- /dev/null
+++ b/include/dt-bindings/clock/cix,sky1-audss.h
@@ -0,0 +1,60 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright 2026 Cix Technology Group Co., Ltd.
+ */
+
+#ifndef _DT_BINDINGS_CLK_CIX_SKY1_AUDSS_H
+#define _DT_BINDINGS_CLK_CIX_SKY1_AUDSS_H
+
+#define CLK_AUD_CLK4_DIV2 0
+#define CLK_AUD_CLK4_DIV4 1
+#define CLK_AUD_CLK5_DIV2 2
+
+#define CLK_DSP_CLK 3
+#define CLK_DSP_BCLK 4
+#define CLK_DSP_PBCLK 5
+
+#define CLK_SRAM_AXI 6
+
+#define CLK_HDA_SYS 7
+#define CLK_HDA_HDA 8
+
+#define CLK_DMAC_AXI 9
+
+#define CLK_WDG_APB 10
+#define CLK_WDG_WDG 11
+
+#define CLK_TIMER_APB 12
+#define CLK_TIMER_TIMER 13
+
+#define CLK_MB_0_APB 14 /* MB0: ap->dsp */
+#define CLK_MB_1_APB 15 /* MB1: dsp->ap */
+
+#define CLK_I2S0_APB 16
+#define CLK_I2S1_APB 17
+#define CLK_I2S2_APB 18
+#define CLK_I2S3_APB 19
+#define CLK_I2S4_APB 20
+#define CLK_I2S5_APB 21
+#define CLK_I2S6_APB 22
+#define CLK_I2S7_APB 23
+#define CLK_I2S8_APB 24
+#define CLK_I2S9_APB 25
+#define CLK_I2S0 26
+#define CLK_I2S1 27
+#define CLK_I2S2 28
+#define CLK_I2S3 29
+#define CLK_I2S4 30
+#define CLK_I2S5 31
+#define CLK_I2S6 32
+#define CLK_I2S7 33
+#define CLK_I2S8 34
+#define CLK_I2S9 35
+
+#define CLK_MCLK0 36
+#define CLK_MCLK1 37
+#define CLK_MCLK2 38
+#define CLK_MCLK3 39
+#define CLK_MCLK4 40
+
+#endif
--
2.50.1
^ permalink raw reply related
* [PATCH v3 4/5] clk: cix: add sky1 audss clock controller
From: joakim.zhang @ 2026-06-10 7:56 UTC (permalink / raw)
To: mturquette, sboyd, bmasney, robh, krzk+dt, conor+dt, p.zabel,
gary.yang
Cc: cix-kernel-upstream, linux-clk, devicetree, linux-kernel,
linux-arm-kernel, Joakim Zhang
In-Reply-To: <20260610075645.3581145-1-joakim.zhang@cixtech.com>
From: Joakim Zhang <joakim.zhang@cixtech.com>
Add a platform driver for the Cix Sky1 Audio Subsystem (AUDSS) internal
clock controller. The driver binds to a cix,sky1-audss-clock device tree
node under the AUDSS syscon, obtains the parent regmap via
syscon_node_to_regmap(), and registers mux/divider/gate composite clocks
for DSP, SRAM, HDA, DMAC, watchdog, timer, mailbox and I2S outputs. Four
SoC-level audio reference clocks are brought up as inputs to the tree.
Signed-off-by: Joakim Zhang <joakim.zhang@cixtech.com>
---
drivers/clk/Kconfig | 1 +
drivers/clk/Makefile | 1 +
drivers/clk/cix/Kconfig | 16 +
drivers/clk/cix/Makefile | 3 +
drivers/clk/cix/clk-sky1-audss.c | 1175 ++++++++++++++++++++++++++++++
5 files changed, 1196 insertions(+)
create mode 100644 drivers/clk/cix/Kconfig
create mode 100644 drivers/clk/cix/Makefile
create mode 100644 drivers/clk/cix/clk-sky1-audss.c
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index b2efbe9f6acb..ead41e45c0f6 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -503,6 +503,7 @@ source "drivers/clk/actions/Kconfig"
source "drivers/clk/analogbits/Kconfig"
source "drivers/clk/aspeed/Kconfig"
source "drivers/clk/bcm/Kconfig"
+source "drivers/clk/cix/Kconfig"
source "drivers/clk/eswin/Kconfig"
source "drivers/clk/hisilicon/Kconfig"
source "drivers/clk/imgtec/Kconfig"
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index a3e2862ebd7e..9135ea6e5a8f 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -118,6 +118,7 @@ obj-$(CONFIG_ARCH_ARTPEC) += axis/
obj-$(CONFIG_ARC_PLAT_AXS10X) += axs10x/
obj-y += bcm/
obj-$(CONFIG_ARCH_BERLIN) += berlin/
+obj-y += cix/
obj-$(CONFIG_ARCH_DAVINCI) += davinci/
obj-$(CONFIG_COMMON_CLK_ESWIN) += eswin/
obj-$(CONFIG_ARCH_HISI) += hisilicon/
diff --git a/drivers/clk/cix/Kconfig b/drivers/clk/cix/Kconfig
new file mode 100644
index 000000000000..3909796f8656
--- /dev/null
+++ b/drivers/clk/cix/Kconfig
@@ -0,0 +1,16 @@
+# SPDX-License-Identifier: GPL-2.0
+# Audio subsystem clock support for Cixtech SoC family
+menu "Clock support for Cixtech audss"
+
+config CLK_SKY1_AUDSS
+ tristate "Cixtech Sky1 Audio Subsystem Clock Driver"
+ depends on ARCH_CIX || COMPILE_TEST
+ select MFD_SYSCON
+ select REGMAP_MMIO
+ select RESET_CONTROLLER
+ help
+ Support for the Audio Subsystem clock controller present on
+ Cixtech Sky1 SoC. This driver provides mux, divider and gate
+ clocks for DSP, I2S, HDA and related blocks in the audio
+ subsystem. Say M or Y here if you want to build this driver.
+endmenu
diff --git a/drivers/clk/cix/Makefile b/drivers/clk/cix/Makefile
new file mode 100644
index 000000000000..bc612f1d08b2
--- /dev/null
+++ b/drivers/clk/cix/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+
+obj-$(CONFIG_CLK_SKY1_AUDSS) += clk-sky1-audss.o
diff --git a/drivers/clk/cix/clk-sky1-audss.c b/drivers/clk/cix/clk-sky1-audss.c
new file mode 100644
index 000000000000..3ec6bea93b73
--- /dev/null
+++ b/drivers/clk/cix/clk-sky1-audss.c
@@ -0,0 +1,1175 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright 2026 Cix Technology Group Co., Ltd.
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/delay.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#include <dt-bindings/clock/cix,sky1-audss.h>
+
+#define INFO_HIFI0 0x00
+#define INFO_CLK_GATE 0x10
+#define INFO_CLK_DIV 0x14
+#define INFO_CLK_MUX 0x18
+#define INFO_MCLK 0x70
+
+#define SKY1_AUDSS_CLK_PARENTS_CNT 4
+#define SKY1_AUDSS_NUM_CLKS (CLK_MCLK4 + 1)
+
+static u32 sky1_reg_save[][2] = {
+ { INFO_HIFI0, 0 },
+ { INFO_CLK_GATE, 0 },
+ { INFO_CLK_DIV, 0 },
+ { INFO_CLK_MUX, 0 },
+ { INFO_MCLK, 0 },
+};
+
+static const char * const sky1_audss_clk_names[SKY1_AUDSS_CLK_PARENTS_CNT] = {
+ "x8k", "x11k", "sys", "48m",
+};
+
+static const u32 sky1_clk_rate_default[SKY1_AUDSS_CLK_PARENTS_CNT] = {
+ 294912000,
+ 270950400,
+ 800000000,
+ 48000000,
+};
+
+static const char * const dsp_clk_parent[] = {
+ "audio_clk4"
+};
+
+static const char * const dsp_bclk_parent[] = {
+ "audio_clk4_div2"
+};
+
+static const char * const dsp_pbclk_parent[] = {
+ "audio_clk4_div4"
+};
+
+static const char * const sram_axi_parent[] = {
+ "audio_clk4_div2"
+};
+
+static const char * const hda_sys_parent[] = {
+ "audio_clk4_div2"
+};
+
+static const char * const hda_hda_parent[] = {
+ "audio_clk5"
+};
+
+static const char * const dmac_axi_parent[] = {
+ "audio_clk4_div2"
+};
+
+static const char * const wdg_apb_parent[] = {
+ "audio_clk5_div2"
+};
+
+static const char * const wdg_wdg_parent[] = {
+ "audio_clk5_div2"
+};
+
+static const char * const timer_apb_parent[] = {
+ "audio_clk4_div4"
+};
+
+static const char * const timer_timer_parent[] = {
+ "audio_clk5_div2"
+};
+
+static const char * const mailbox_apb_parent[] = {
+ "audio_clk4_div4"
+};
+
+static const char * const i2s_apb_parent[] = {
+ "audio_clk4_div4"
+};
+
+static const char * const i2s0_parents[] = {
+ "audio_clk0", "audio_clk2"
+};
+
+static const char * const i2s1_parents[] = {
+ "audio_clk0", "audio_clk2"
+};
+
+static const char * const i2s2_parents[] = {
+ "audio_clk0", "audio_clk2"
+};
+
+static const char * const i2s3_parents[] = {
+ "audio_clk0", "audio_clk2"
+};
+
+static const char * const i2s4_parents[] = {
+ "audio_clk0", "audio_clk2"
+};
+
+static const char * const i2s5_parents[] = {
+ "audio_clk0", "audio_clk2"
+};
+
+static const char * const i2s6_parents[] = {
+ "audio_clk0", "audio_clk2"
+};
+
+static const char * const i2s7_parents[] = {
+ "audio_clk0", "audio_clk2"
+};
+
+static const char * const i2s8_parents[] = {
+ "audio_clk0", "audio_clk2"
+};
+
+static const char * const i2s9_parents[] = {
+ "audio_clk0", "audio_clk2"
+};
+
+static const char * const mclk_parents[] = {
+ "audio_clk0", "audio_clk2"
+};
+
+static const u32 i2s3_mux_table[] = { 0, 2 };
+static const u32 i2s4_mux_table[] = { 0, 2 };
+
+/*
+ * audss composite clock definition
+ */
+struct muxdiv_cfg {
+ int offset;
+ u8 shift;
+ u8 width;
+ u8 flags;
+};
+
+struct gate_cfg {
+ int offset;
+ u8 shift;
+ u8 flags;
+};
+
+struct composite_clk_cfg {
+ u32 id;
+ const char * const name;
+ const char * const *parent_names;
+ int num_parents;
+ const u32 *mux_table;
+ struct muxdiv_cfg *mux_cfg;
+ struct muxdiv_cfg *div_cfg;
+ struct gate_cfg *gate_cfg;
+ unsigned long flags;
+};
+
+#define CFG(_id,\
+ _name,\
+ _parent_names,\
+ _mux_table,\
+ _mux_offset, _mux_shift, _mux_width, _mux_flags,\
+ _div_offset, _div_shift, _div_width, _div_flags,\
+ _gate_offset, _gate_shift, _gate_flags,\
+ _flags)\
+{\
+ .id = _id,\
+ .name = _name,\
+ .parent_names = _parent_names,\
+ .num_parents = ARRAY_SIZE(_parent_names),\
+ .mux_table = _mux_table,\
+ .mux_cfg = &(struct muxdiv_cfg) { _mux_offset, _mux_shift, _mux_width, _mux_flags },\
+ .div_cfg = &(struct muxdiv_cfg) { _div_offset, _div_shift, _div_width, _div_flags },\
+ .gate_cfg = &(struct gate_cfg) { _gate_offset, _gate_shift, _gate_flags },\
+ .flags = _flags,\
+}
+
+static const struct composite_clk_cfg sky1_audss_clks[] = {
+ /* dsp */
+ CFG(CLK_DSP_CLK,
+ "audss_dsp_clk",
+ dsp_clk_parent,
+ NULL,
+ -1, 0, 0, 0,
+ INFO_CLK_DIV, 0, 2, 0,
+ INFO_HIFI0, 0, 0,
+ 0),
+ CFG(CLK_DSP_BCLK,
+ "audss_dsp_bclk",
+ dsp_bclk_parent,
+ NULL,
+ -1, 0, 0, 0,
+ INFO_CLK_DIV, 0, 2, 0,
+ -1, 0, 0,
+ 0),
+ CFG(CLK_DSP_PBCLK,
+ "audss_dsp_pbclk",
+ dsp_pbclk_parent,
+ NULL,
+ -1, 0, 0, 0,
+ INFO_CLK_DIV, 0, 2, 0,
+ -1, 0, 0,
+ 0),
+ /* sram */
+ CFG(CLK_SRAM_AXI,
+ "audss_sram_axi",
+ sram_axi_parent,
+ NULL,
+ -1, 0, 0, 0,
+ INFO_CLK_DIV, 0, 2, 0,
+ INFO_CLK_GATE, 16, 0,
+ 0),
+ /* hda */
+ CFG(CLK_HDA_SYS,
+ "audss_hda_sys",
+ hda_sys_parent,
+ NULL,
+ -1, 0, 0, 0,
+ INFO_CLK_DIV, 0, 2, 0,
+ INFO_CLK_GATE, 14, 0,
+ 0),
+ CFG(CLK_HDA_HDA,
+ "audss_hda_hda",
+ hda_hda_parent,
+ NULL,
+ -1, 0, 0, 0,
+ -1, 0, 0, 0,
+ INFO_CLK_GATE, 14, 0,
+ 0),
+ /* dmac */
+ CFG(CLK_DMAC_AXI,
+ "audss_dmac_axi",
+ dmac_axi_parent,
+ NULL,
+ -1, 0, 0, 0,
+ INFO_CLK_DIV, 0, 2, 0,
+ INFO_CLK_GATE, 15, 0,
+ 0),
+ /* wdg */
+ CFG(CLK_WDG_APB,
+ "audss_wdg_apb",
+ wdg_apb_parent,
+ NULL,
+ -1, 0, 0, 0,
+ -1, 0, 0, 0,
+ INFO_CLK_GATE, 10, 0,
+ 0),
+ CFG(CLK_WDG_WDG,
+ "audss_wdg_wdg",
+ wdg_wdg_parent,
+ NULL,
+ -1, 0, 0, 0,
+ -1, 0, 0, 0,
+ INFO_CLK_GATE, 10, 0,
+ 0),
+ /* timer */
+ CFG(CLK_TIMER_APB,
+ "audss_timer_apb",
+ timer_apb_parent,
+ NULL,
+ -1, 0, 0, 0,
+ INFO_CLK_DIV, 0, 2, 0,
+ INFO_CLK_GATE, 11, 0,
+ 0),
+ CFG(CLK_TIMER_TIMER,
+ "audss_timer_timer",
+ timer_timer_parent,
+ NULL,
+ -1, 0, 0, 0,
+ -1, 0, 0, 0,
+ INFO_CLK_GATE, 11, 0,
+ 0),
+ /* mailbox: mb0(ap->dsp), mb1(dsp->ap) */
+ CFG(CLK_MB_0_APB,
+ "audss_mb_0_apb",
+ mailbox_apb_parent,
+ NULL,
+ -1, 0, 0, 0,
+ -1, 0, 0, 0,
+ INFO_CLK_GATE, 12, 0,
+ 0),
+ CFG(CLK_MB_1_APB,
+ "audss_mb_1_apb",
+ mailbox_apb_parent,
+ NULL,
+ -1, 0, 0, 0,
+ -1, 0, 0, 0,
+ INFO_CLK_GATE, 13, 0,
+ 0),
+ /* i2s */
+ CFG(CLK_I2S0_APB,
+ "audss_i2s0_apb",
+ i2s_apb_parent,
+ NULL,
+ -1, 0, 0, 0,
+ INFO_CLK_DIV, 0, 2, 0,
+ INFO_CLK_GATE, 0, 0,
+ 0),
+ CFG(CLK_I2S1_APB,
+ "audss_i2s1_apb",
+ i2s_apb_parent,
+ NULL,
+ -1, 0, 0, 0,
+ INFO_CLK_DIV, 0, 2, 0,
+ INFO_CLK_GATE, 1, 0,
+ 0),
+ CFG(CLK_I2S2_APB,
+ "audss_i2s2_apb",
+ i2s_apb_parent,
+ NULL,
+ -1, 0, 0, 0,
+ INFO_CLK_DIV, 0, 2, 0,
+ INFO_CLK_GATE, 2, 0,
+ 0),
+ CFG(CLK_I2S3_APB,
+ "audss_i2s3_apb",
+ i2s_apb_parent,
+ NULL,
+ -1, 0, 0, 0,
+ INFO_CLK_DIV, 0, 2, 0,
+ INFO_CLK_GATE, 3, 0,
+ 0),
+ CFG(CLK_I2S4_APB,
+ "audss_i2s4_apb",
+ i2s_apb_parent,
+ NULL,
+ -1, 0, 0, 0,
+ INFO_CLK_DIV, 0, 2, 0,
+ INFO_CLK_GATE, 4, 0,
+ 0),
+ CFG(CLK_I2S5_APB,
+ "audss_i2s5_apb",
+ i2s_apb_parent,
+ NULL,
+ -1, 0, 0, 0,
+ INFO_CLK_DIV, 0, 2, 0,
+ INFO_CLK_GATE, 5, 0,
+ 0),
+ CFG(CLK_I2S6_APB,
+ "audss_i2s6_apb",
+ i2s_apb_parent,
+ NULL,
+ -1, 0, 0, 0,
+ INFO_CLK_DIV, 0, 2, 0,
+ INFO_CLK_GATE, 6, 0,
+ 0),
+ CFG(CLK_I2S7_APB,
+ "audss_i2s7_apb",
+ i2s_apb_parent,
+ NULL,
+ -1, 0, 0, 0,
+ INFO_CLK_DIV, 0, 2, 0,
+ INFO_CLK_GATE, 7, 0,
+ 0),
+ CFG(CLK_I2S8_APB,
+ "audss_i2s8_apb",
+ i2s_apb_parent,
+ NULL,
+ -1, 0, 0, 0,
+ INFO_CLK_DIV, 0, 2, 0,
+ INFO_CLK_GATE, 8, 0,
+ 0),
+ CFG(CLK_I2S9_APB,
+ "audss_i2s9_apb",
+ i2s_apb_parent,
+ NULL,
+ -1, 0, 0, 0,
+ INFO_CLK_DIV, 0, 2, 0,
+ INFO_CLK_GATE, 9, 0,
+ 0),
+ CFG(CLK_I2S0,
+ "audss_i2s0",
+ i2s0_parents,
+ NULL,
+ INFO_CLK_MUX, 0, 2, 0,
+ INFO_CLK_DIV, 2, 2, 0,
+ INFO_CLK_GATE, 0, 0,
+ 0),
+ CFG(CLK_I2S1,
+ "audss_i2s1",
+ i2s1_parents,
+ NULL,
+ INFO_CLK_MUX, 2, 2, 0,
+ INFO_CLK_DIV, 4, 2, 0,
+ INFO_CLK_GATE, 1, 0,
+ 0),
+ CFG(CLK_I2S2,
+ "audss_i2s2",
+ i2s2_parents,
+ NULL,
+ INFO_CLK_MUX, 4, 2, 0,
+ INFO_CLK_DIV, 6, 2, 0,
+ INFO_CLK_GATE, 2, 0,
+ 0),
+ CFG(CLK_I2S3,
+ "audss_i2s3",
+ i2s3_parents,
+ i2s3_mux_table,
+ INFO_CLK_MUX, 6, 2, 0,
+ INFO_CLK_DIV, 8, 2, 0,
+ INFO_CLK_GATE, 3, 0,
+ 0),
+ CFG(CLK_I2S4,
+ "audss_i2s4",
+ i2s4_parents,
+ i2s4_mux_table,
+ INFO_CLK_MUX, 8, 2, 0,
+ INFO_CLK_DIV, 10, 2, 0,
+ INFO_CLK_GATE, 4, 0,
+ 0),
+ CFG(CLK_I2S5,
+ "audss_i2s5",
+ i2s5_parents,
+ NULL,
+ INFO_CLK_MUX, 10, 2, 0,
+ INFO_CLK_DIV, 12, 2, 0,
+ INFO_CLK_GATE, 5, 0,
+ 0),
+ CFG(CLK_I2S6,
+ "audss_i2s6",
+ i2s6_parents,
+ NULL,
+ INFO_CLK_MUX, 12, 2, 0,
+ INFO_CLK_DIV, 14, 2, 0,
+ INFO_CLK_GATE, 6, 0,
+ 0),
+ CFG(CLK_I2S7,
+ "audss_i2s7",
+ i2s7_parents,
+ NULL,
+ INFO_CLK_MUX, 14, 2, 0,
+ INFO_CLK_DIV, 16, 2, 0,
+ INFO_CLK_GATE, 7, 0,
+ 0),
+ CFG(CLK_I2S8,
+ "audss_i2s8",
+ i2s8_parents,
+ NULL,
+ INFO_CLK_MUX, 16, 2, 0,
+ INFO_CLK_DIV, 18, 2, 0,
+ INFO_CLK_GATE, 8, 0,
+ 0),
+ CFG(CLK_I2S9,
+ "audss_i2s9",
+ i2s9_parents,
+ NULL,
+ INFO_CLK_MUX, 18, 2, 0,
+ INFO_CLK_DIV, 20, 2, 0,
+ INFO_CLK_GATE, 9, 0,
+ 0),
+ /* mclk */
+ CFG(CLK_MCLK0,
+ "audss_mclk0",
+ mclk_parents,
+ NULL,
+ INFO_MCLK, 5, 1, 0,
+ -1, 0, 0, 0,
+ INFO_MCLK, 0, 0,
+ 0),
+ CFG(CLK_MCLK1,
+ "audss_mclk1",
+ mclk_parents,
+ NULL,
+ INFO_MCLK, 6, 1, 0,
+ -1, 0, 0, 0,
+ INFO_MCLK, 1, 0,
+ 0),
+ CFG(CLK_MCLK2,
+ "audss_mclk2",
+ mclk_parents,
+ NULL,
+ INFO_MCLK, 7, 1, 0,
+ -1, 0, 0, 0,
+ INFO_MCLK, 2, 0,
+ 0),
+ CFG(CLK_MCLK3,
+ "audss_mclk3",
+ mclk_parents,
+ NULL,
+ INFO_MCLK, 8, 1, 0,
+ -1, 0, 0, 0,
+ INFO_MCLK, 3, 0,
+ 0),
+ CFG(CLK_MCLK4,
+ "audss_mclk4",
+ mclk_parents,
+ NULL,
+ INFO_MCLK, 9, 1, 0,
+ -1, 0, 0, 0,
+ INFO_MCLK, 4, 0,
+ 0),
+};
+
+struct sky1_audss_clks_devtype_data {
+ u32 (*reg_save)[2];
+ size_t reg_save_size;
+ const char * const *clk_names;
+ size_t clk_num;
+ const u32 *clk_rate_default;
+ const struct composite_clk_cfg *clk_cfg;
+ size_t clk_cfg_size;
+};
+
+struct sky1_audss_clks_priv {
+ struct device *dev;
+ struct regmap *regmap_cru;
+ struct clk *clks[SKY1_AUDSS_CLK_PARENTS_CNT];
+ struct reset_control *rst_noc;
+ const struct sky1_audss_clks_devtype_data *devtype_data;
+ spinlock_t lock;
+ struct clk_hw_onecell_data *clk_data;
+};
+
+/*
+ * clk_ops for audss clock mux/divider/gate
+ */
+struct sky1_clk_divider {
+ struct clk_divider div;
+ struct regmap *regmap;
+ int offset;
+};
+
+struct sky1_clk_gate {
+ struct clk_gate gate;
+ struct regmap *regmap;
+ int offset;
+};
+
+struct sky1_clk_mux {
+ struct clk_mux mux;
+ struct regmap *regmap;
+ int offset;
+};
+
+static inline struct sky1_clk_mux *to_sky1_clk_mux(struct clk_mux *mux)
+{
+ return container_of(mux, struct sky1_clk_mux, mux);
+}
+
+static u8 sky1_audss_clk_mux_get_parent(struct clk_hw *hw)
+{
+ struct clk_mux *mux = to_clk_mux(hw);
+ struct sky1_clk_mux *sky1_mux = to_sky1_clk_mux(mux);
+ u32 val;
+
+ regmap_read(sky1_mux->regmap, sky1_mux->offset, &val);
+ val = val >> mux->shift;
+ val &= mux->mask;
+
+ return clk_mux_val_to_index(hw, mux->table, mux->flags, val);
+}
+
+static int sky1_audss_clk_mux_set_parent(struct clk_hw *hw, u8 index)
+{
+ struct clk_mux *mux = to_clk_mux(hw);
+ u32 val = clk_mux_index_to_val(mux->table, mux->flags, index);
+ struct sky1_clk_mux *sky1_mux = to_sky1_clk_mux(mux);
+ unsigned long flags = 0;
+ u32 reg;
+
+ if (mux->lock)
+ spin_lock_irqsave(mux->lock, flags);
+ else
+ __acquire(mux->lock);
+
+ if (mux->flags & CLK_MUX_HIWORD_MASK) {
+ reg = mux->mask << (mux->shift + 16);
+ } else {
+ regmap_read(sky1_mux->regmap, sky1_mux->offset, ®);
+ reg &= ~(mux->mask << mux->shift);
+ }
+ val = val << mux->shift;
+ reg |= val;
+ regmap_write(sky1_mux->regmap, sky1_mux->offset, reg);
+
+ if (mux->lock)
+ spin_unlock_irqrestore(mux->lock, flags);
+ else
+ __release(mux->lock);
+
+ return 0;
+}
+
+static int sky1_audss_clk_mux_determine_rate(struct clk_hw *hw,
+ struct clk_rate_request *req)
+{
+ struct clk_mux *mux = to_clk_mux(hw);
+
+ return clk_mux_determine_rate_flags(hw, req, mux->flags);
+}
+
+static const struct clk_ops sky1_audss_clk_mux_ops = {
+ .get_parent = sky1_audss_clk_mux_get_parent,
+ .set_parent = sky1_audss_clk_mux_set_parent,
+ .determine_rate = sky1_audss_clk_mux_determine_rate,
+};
+
+static inline struct sky1_clk_divider *to_sky1_clk_divider(struct clk_divider *div)
+{
+ return container_of(div, struct sky1_clk_divider, div);
+}
+
+static unsigned long sky1_audss_clk_divider_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct clk_divider *divider = to_clk_divider(hw);
+ struct sky1_clk_divider *sky1_div = to_sky1_clk_divider(divider);
+ unsigned int val;
+
+ regmap_read(sky1_div->regmap, sky1_div->offset, &val);
+ val = val >> divider->shift;
+ val &= clk_div_mask(divider->width);
+
+ return divider_recalc_rate(hw, parent_rate, val, divider->table,
+ divider->flags, divider->width);
+}
+
+static int sky1_audss_clk_divider_determine_rate(struct clk_hw *hw,
+ struct clk_rate_request *req)
+{
+ struct clk_divider *divider = to_clk_divider(hw);
+ struct sky1_clk_divider *sky1_div = to_sky1_clk_divider(divider);
+
+ /* if read only, just return current value */
+ if (divider->flags & CLK_DIVIDER_READ_ONLY) {
+ u32 val;
+
+ regmap_read(sky1_div->regmap, sky1_div->offset, &val);
+ val = val >> divider->shift;
+ val &= clk_div_mask(divider->width);
+
+ return divider_ro_determine_rate(hw, req, divider->table,
+ divider->width,
+ divider->flags, val);
+ }
+
+ return divider_determine_rate(hw, req, divider->table, divider->width,
+ divider->flags);
+}
+
+static int sky1_audss_clk_divider_set_rate(struct clk_hw *hw,
+ unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct clk_divider *divider = to_clk_divider(hw);
+ struct sky1_clk_divider *sky1_div = to_sky1_clk_divider(divider);
+ int value;
+ unsigned long flags = 0;
+ u32 val;
+
+ value = divider_get_val(rate, parent_rate, divider->table,
+ divider->width, divider->flags);
+ if (value < 0)
+ return value;
+
+ if (divider->lock)
+ spin_lock_irqsave(divider->lock, flags);
+ else
+ __acquire(divider->lock);
+
+ if (divider->flags & CLK_DIVIDER_HIWORD_MASK) {
+ val = clk_div_mask(divider->width) << (divider->shift + 16);
+ } else {
+ regmap_read(sky1_div->regmap, sky1_div->offset, &val);
+ val &= ~(clk_div_mask(divider->width) << divider->shift);
+ }
+ val |= (u32)value << divider->shift;
+ regmap_write(sky1_div->regmap, sky1_div->offset, val);
+
+ if (divider->lock)
+ spin_unlock_irqrestore(divider->lock, flags);
+ else
+ __release(divider->lock);
+
+ return 0;
+}
+
+static const struct clk_ops sky1_audss_clk_divider_ops = {
+ .recalc_rate = sky1_audss_clk_divider_recalc_rate,
+ .determine_rate = sky1_audss_clk_divider_determine_rate,
+ .set_rate = sky1_audss_clk_divider_set_rate,
+};
+
+static inline struct sky1_clk_gate *to_sky1_clk_gate(struct clk_gate *gate)
+{
+ return container_of(gate, struct sky1_clk_gate, gate);
+}
+
+static void sky1_audss_clk_gate_endisable(struct clk_hw *hw, int enable)
+{
+ struct clk_gate *gate = to_clk_gate(hw);
+ struct sky1_clk_gate *sky1_gate = to_sky1_clk_gate(gate);
+ int set = gate->flags & CLK_GATE_SET_TO_DISABLE ? 1 : 0;
+ unsigned long flags = 0;
+ u32 reg;
+
+ set ^= enable;
+
+ if (gate->lock)
+ spin_lock_irqsave(gate->lock, flags);
+ else
+ __acquire(gate->lock);
+
+ if (gate->flags & CLK_GATE_HIWORD_MASK) {
+ reg = BIT(gate->bit_idx + 16);
+ if (set)
+ reg |= BIT(gate->bit_idx);
+ } else {
+ regmap_read(sky1_gate->regmap, sky1_gate->offset, ®);
+
+ if (set)
+ reg |= BIT(gate->bit_idx);
+ else
+ reg &= ~BIT(gate->bit_idx);
+ }
+
+ regmap_write(sky1_gate->regmap, sky1_gate->offset, reg);
+
+ if (gate->lock)
+ spin_unlock_irqrestore(gate->lock, flags);
+ else
+ __release(gate->lock);
+}
+
+static int sky1_audss_clk_gate_enable(struct clk_hw *hw)
+{
+ sky1_audss_clk_gate_endisable(hw, 1);
+
+ return 0;
+}
+
+static void sky1_audss_clk_gate_disable(struct clk_hw *hw)
+{
+ sky1_audss_clk_gate_endisable(hw, 0);
+}
+
+static int sky1_audss_clk_gate_is_enabled(struct clk_hw *hw)
+{
+ struct clk_gate *gate = to_clk_gate(hw);
+ struct sky1_clk_gate *sky1_gate = to_sky1_clk_gate(gate);
+ u32 reg;
+
+ regmap_read(sky1_gate->regmap, sky1_gate->offset, ®);
+
+ /* if a set bit disables this clk, flip it before masking */
+ if (gate->flags & CLK_GATE_SET_TO_DISABLE)
+ reg ^= BIT(gate->bit_idx);
+
+ reg &= BIT(gate->bit_idx);
+
+ return !!reg;
+}
+
+static const struct clk_ops sky1_audss_clk_gate_ops = {
+ .enable = sky1_audss_clk_gate_enable,
+ .disable = sky1_audss_clk_gate_disable,
+ .is_enabled = sky1_audss_clk_gate_is_enabled,
+};
+
+static struct clk_hw *sky1_audss_clk_register(struct device *dev,
+ const char *name,
+ const char * const *parent_names,
+ int num_parents,
+ struct regmap *regmap,
+ const u32 *mux_table,
+ struct muxdiv_cfg *mux_cfg,
+ struct muxdiv_cfg *div_cfg,
+ struct gate_cfg *gate_cfg,
+ unsigned long flags,
+ spinlock_t *lock)
+{
+ const struct clk_ops *sky1_mux_ops = NULL;
+ const struct clk_ops *sky1_div_ops = NULL;
+ const struct clk_ops *sky1_gate_ops = NULL;
+ struct clk_hw *hw = ERR_PTR(-ENOMEM);
+ struct sky1_clk_divider *sky1_div = NULL;
+ struct sky1_clk_gate *sky1_gate = NULL;
+ struct sky1_clk_mux *sky1_mux = NULL;
+
+ if (mux_cfg->offset >= 0) {
+ sky1_mux = devm_kzalloc(dev, sizeof(*sky1_mux), GFP_KERNEL);
+ if (!sky1_mux)
+ return ERR_PTR(-ENOMEM);
+
+ sky1_mux->mux.reg = NULL;
+ sky1_mux->mux.shift = mux_cfg->shift;
+ sky1_mux->mux.mask = BIT(mux_cfg->width) - 1;
+ sky1_mux->mux.flags = mux_cfg->flags;
+ sky1_mux->mux.table = mux_table;
+ sky1_mux->mux.lock = lock;
+ sky1_mux_ops = &sky1_audss_clk_mux_ops;
+ sky1_mux->regmap = regmap;
+ sky1_mux->offset = mux_cfg->offset;
+ }
+
+ if (div_cfg->offset >= 0) {
+ sky1_div = devm_kzalloc(dev, sizeof(*sky1_div), GFP_KERNEL);
+ if (!sky1_div)
+ return ERR_PTR(-ENOMEM);
+
+ sky1_div->div.reg = NULL;
+ sky1_div->div.shift = div_cfg->shift;
+ sky1_div->div.width = div_cfg->width;
+ sky1_div->div.flags = div_cfg->flags | CLK_DIVIDER_POWER_OF_TWO;
+ sky1_div->div.lock = lock;
+ sky1_div_ops = &sky1_audss_clk_divider_ops;
+ sky1_div->regmap = regmap;
+ sky1_div->offset = div_cfg->offset;
+ }
+
+ if (gate_cfg->offset >= 0) {
+ sky1_gate = devm_kzalloc(dev, sizeof(*sky1_gate), GFP_KERNEL);
+ if (!sky1_gate)
+ return ERR_PTR(-ENOMEM);
+
+ sky1_gate->gate.reg = NULL;
+ sky1_gate->gate.bit_idx = gate_cfg->shift;
+ sky1_gate->gate.flags = gate_cfg->flags;
+ sky1_gate->gate.lock = lock;
+ sky1_gate_ops = &sky1_audss_clk_gate_ops;
+ sky1_gate->regmap = regmap;
+ sky1_gate->offset = gate_cfg->offset;
+ }
+
+ hw = clk_hw_register_composite(dev, name, parent_names, num_parents,
+ sky1_mux ? &sky1_mux->mux.hw : NULL, sky1_mux_ops,
+ sky1_div ? &sky1_div->div.hw : NULL, sky1_div_ops,
+ sky1_gate ? &sky1_gate->gate.hw : NULL, sky1_gate_ops,
+ flags);
+ if (IS_ERR(hw)) {
+ dev_err(dev, "register %s clock failed with err = %ld\n",
+ name, PTR_ERR(hw));
+ return hw;
+ }
+
+ return hw;
+}
+
+static int sky1_audss_clks_get(struct sky1_audss_clks_priv *priv)
+{
+ const struct sky1_audss_clks_devtype_data *devtype_data = priv->devtype_data;
+ int i;
+
+ for (i = 0; i < devtype_data->clk_num; i++) {
+ priv->clks[i] = devm_clk_get(priv->dev, devtype_data->clk_names[i]);
+ if (IS_ERR(priv->clks[i]))
+ return dev_err_probe(priv->dev, PTR_ERR(priv->clks[i]),
+ "failed to get clock %s", devtype_data->clk_names[i]);
+ }
+
+ return 0;
+}
+
+static int sky1_audss_clks_enable(struct sky1_audss_clks_priv *priv)
+{
+ const struct sky1_audss_clks_devtype_data *devtype_data = priv->devtype_data;
+ int i, err;
+
+ for (i = 0; i < devtype_data->clk_num; i++) {
+ err = clk_prepare_enable(priv->clks[i]);
+ if (err) {
+ dev_err(priv->dev, "failed to enable clock %s\n",
+ devtype_data->clk_names[i]);
+ goto err_clks;
+ }
+ }
+
+ return 0;
+
+err_clks:
+ while (--i >= 0)
+ clk_disable_unprepare(priv->clks[i]);
+
+ return err;
+}
+
+static void sky1_audss_clks_disable(struct sky1_audss_clks_priv *priv)
+{
+ const struct sky1_audss_clks_devtype_data *devtype_data = priv->devtype_data;
+ int i;
+
+ for (i = 0; i < devtype_data->clk_num; i++)
+ clk_disable_unprepare(priv->clks[i]);
+}
+
+static int sky1_audss_clks_set_rate(struct sky1_audss_clks_priv *priv)
+{
+ const struct sky1_audss_clks_devtype_data *devtype_data = priv->devtype_data;
+ int i, err;
+
+ for (i = 0; i < devtype_data->clk_num; i++) {
+ err = clk_set_rate(priv->clks[i], devtype_data->clk_rate_default[i]);
+ if (err) {
+ dev_err(priv->dev, "failed to set clock rate %s\n",
+ devtype_data->clk_names[i]);
+ return err;
+ }
+ }
+
+ return 0;
+}
+
+/* register sky1 audio subsystem clocks */
+static int sky1_audss_clk_probe(struct platform_device *pdev)
+{
+ const struct sky1_audss_clks_devtype_data *devtype_data;
+ struct sky1_audss_clks_priv *priv;
+ struct device_node *parent_np;
+ struct device *dev = &pdev->dev;
+ struct reset_control *rst_noc;
+ struct clk_hw **clk_table;
+ struct regmap *regmap_cru;
+ int i, ret;
+
+ parent_np = of_get_parent(pdev->dev.of_node);
+ regmap_cru = syscon_node_to_regmap(parent_np);
+ of_node_put(parent_np);
+ if (IS_ERR(regmap_cru))
+ return dev_err_probe(dev, PTR_ERR(regmap_cru),
+ "unable to get audss cru regmap");
+
+ devtype_data = device_get_match_data(dev);
+ if (!devtype_data)
+ return -ENODEV;
+
+ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ spin_lock_init(&priv->lock);
+
+ priv->clk_data = devm_kzalloc(&pdev->dev,
+ struct_size(priv->clk_data, hws, SKY1_AUDSS_NUM_CLKS),
+ GFP_KERNEL);
+ if (!priv->clk_data)
+ return -ENOMEM;
+
+ priv->clk_data->num = SKY1_AUDSS_NUM_CLKS;
+ clk_table = priv->clk_data->hws;
+
+ priv->dev = dev;
+ priv->regmap_cru = regmap_cru;
+ priv->devtype_data = devtype_data;
+
+ ret = sky1_audss_clks_get(priv);
+ if (ret)
+ return ret;
+
+ rst_noc = devm_reset_control_get_exclusive(dev, NULL);
+ if (IS_ERR(rst_noc))
+ return dev_err_probe(dev, PTR_ERR(rst_noc),
+ "failed to get noc reset");
+ priv->rst_noc = rst_noc;
+
+ platform_set_drvdata(pdev, priv);
+
+ ret = sky1_audss_clks_enable(priv);
+ if (ret) {
+ dev_err(dev, "failed to enable clocks\n");
+ return ret;
+ }
+
+ /*
+ * Enable runtime PM here to allow the clock core using runtime PM
+ * for the registered clocks.
+ */
+ pm_runtime_get_noresume(dev);
+ pm_runtime_set_active(dev);
+ pm_runtime_enable(dev);
+
+ ret = sky1_audss_clks_set_rate(priv);
+ if (ret) {
+ dev_err(dev, "failed to set clocks rate\n");
+ goto fail_clks_set;
+ }
+
+ /* assert reset */
+ reset_control_assert(rst_noc);
+ usleep_range(1, 2);
+
+ /* deassert reset */
+ reset_control_deassert(rst_noc);
+
+ /* audio_clk4 clock fixed divider */
+ clk_table[CLK_AUD_CLK4_DIV2] =
+ devm_clk_hw_register_fixed_factor(dev,
+ "audio_clk4_div2",
+ "audio_clk4",
+ 0,
+ 1, 2);
+ if (IS_ERR(clk_table[CLK_AUD_CLK4_DIV2])) {
+ ret = PTR_ERR(clk_table[CLK_AUD_CLK4_DIV2]);
+ dev_err(dev, "failed to register clock %d, ret:%d\n", CLK_AUD_CLK4_DIV2, ret);
+ goto fail_fixed_clk;
+ }
+
+ clk_table[CLK_AUD_CLK4_DIV4] =
+ devm_clk_hw_register_fixed_factor(dev,
+ "audio_clk4_div4",
+ "audio_clk4",
+ 0,
+ 1, 4);
+ if (IS_ERR(clk_table[CLK_AUD_CLK4_DIV4])) {
+ ret = PTR_ERR(clk_table[CLK_AUD_CLK4_DIV4]);
+ dev_err(dev, "failed to register clock %d, ret:%d\n", CLK_AUD_CLK4_DIV4, ret);
+ goto fail_fixed_clk;
+ }
+
+ /* audio_clk5 clock fixed divider */
+ clk_table[CLK_AUD_CLK5_DIV2] =
+ devm_clk_hw_register_fixed_factor(dev,
+ "audio_clk5_div2",
+ "audio_clk5",
+ 0,
+ 1, 2);
+ if (IS_ERR(clk_table[CLK_AUD_CLK5_DIV2])) {
+ ret = PTR_ERR(clk_table[CLK_AUD_CLK5_DIV2]);
+ dev_err(dev, "failed to register clock %d, ret:%d\n", CLK_AUD_CLK5_DIV2, ret);
+ goto fail_fixed_clk;
+ }
+
+ for (i = 0; i < devtype_data->clk_cfg_size; i++) {
+ clk_table[devtype_data->clk_cfg[i].id] =
+ sky1_audss_clk_register(dev,
+ devtype_data->clk_cfg[i].name,
+ devtype_data->clk_cfg[i].parent_names,
+ devtype_data->clk_cfg[i].num_parents,
+ regmap_cru,
+ devtype_data->clk_cfg[i].mux_table,
+ devtype_data->clk_cfg[i].mux_cfg,
+ devtype_data->clk_cfg[i].div_cfg,
+ devtype_data->clk_cfg[i].gate_cfg,
+ devtype_data->clk_cfg[i].flags,
+ &priv->lock);
+ if (IS_ERR(clk_table[devtype_data->clk_cfg[i].id])) {
+ ret = PTR_ERR(clk_table[devtype_data->clk_cfg[i].id]);
+ dev_err(dev, "failed to register clock %d, ret:%d\n",
+ devtype_data->clk_cfg[i].id, ret);
+ goto fail_array_clk;
+ }
+ }
+
+ ret = devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get, priv->clk_data);
+ if (ret) {
+ dev_err(dev, "failed to add clock provider: %d\n", ret);
+ goto fail_register;
+ }
+
+ pm_runtime_put_sync(dev);
+
+ return 0;
+
+fail_register:
+fail_array_clk:
+ while (i--)
+ clk_hw_unregister_composite(clk_table[devtype_data->clk_cfg[i].id]);
+fail_fixed_clk:
+fail_clks_set:
+ pm_runtime_put_sync(dev);
+ pm_runtime_disable(dev);
+ return ret;
+}
+
+static void sky1_audss_clk_remove(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct sky1_audss_clks_priv *priv = dev_get_drvdata(dev);
+ const struct sky1_audss_clks_devtype_data *devtype_data = priv->devtype_data;
+ int i = 0;
+
+ for (i = 0; i < devtype_data->clk_cfg_size; i++)
+ clk_hw_unregister_composite(priv->clk_data->hws[devtype_data->clk_cfg[i].id]);
+
+ if (!pm_runtime_status_suspended(dev))
+ pm_runtime_force_suspend(dev);
+
+ pm_runtime_disable(dev);
+}
+
+static int __maybe_unused sky1_audss_clk_runtime_suspend(struct device *dev)
+{
+ struct sky1_audss_clks_priv *priv = dev_get_drvdata(dev);
+ const struct sky1_audss_clks_devtype_data *devtype_data = priv->devtype_data;
+ unsigned long flags;
+ int i;
+
+ spin_lock_irqsave(&priv->lock, flags);
+ for (i = 0; i < devtype_data->reg_save_size; i++)
+ regmap_read(priv->regmap_cru,
+ devtype_data->reg_save[i][0], &devtype_data->reg_save[i][1]);
+ spin_unlock_irqrestore(&priv->lock, flags);
+
+ reset_control_assert(priv->rst_noc);
+
+ sky1_audss_clks_disable(priv);
+
+ return 0;
+}
+
+static int __maybe_unused sky1_audss_clk_runtime_resume(struct device *dev)
+{
+ struct sky1_audss_clks_priv *priv = dev_get_drvdata(dev);
+ const struct sky1_audss_clks_devtype_data *devtype_data = priv->devtype_data;
+ unsigned long flags;
+ int i, ret;
+
+ ret = sky1_audss_clks_enable(priv);
+ if (ret) {
+ dev_err(dev, "failed to enable clocks\n");
+ return ret;
+ }
+
+ reset_control_deassert(priv->rst_noc);
+
+ spin_lock_irqsave(&priv->lock, flags);
+ for (i = 0; i < devtype_data->reg_save_size; i++)
+ regmap_write(priv->regmap_cru,
+ devtype_data->reg_save[i][0], devtype_data->reg_save[i][1]);
+ spin_unlock_irqrestore(&priv->lock, flags);
+
+ return 0;
+}
+
+static const struct dev_pm_ops sky1_audss_clk_pm_ops = {
+ SET_RUNTIME_PM_OPS(sky1_audss_clk_runtime_suspend,
+ sky1_audss_clk_runtime_resume, NULL)
+ SET_LATE_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
+ pm_runtime_force_resume)
+};
+
+static const struct sky1_audss_clks_devtype_data sky1_devtype_data = {
+ .reg_save = sky1_reg_save,
+ .reg_save_size = ARRAY_SIZE(sky1_reg_save),
+ .clk_names = sky1_audss_clk_names,
+ .clk_num = ARRAY_SIZE(sky1_audss_clk_names),
+ .clk_rate_default = sky1_clk_rate_default,
+ .clk_cfg = sky1_audss_clks,
+ .clk_cfg_size = ARRAY_SIZE(sky1_audss_clks),
+};
+
+static const struct of_device_id sky1_audss_clk_of_match[] = {
+ { .compatible = "cix,sky1-audss-clock", .data = &sky1_devtype_data, },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, sky1_audss_clk_of_match);
+
+static struct platform_driver sky1_audss_clk_driver = {
+ .probe = sky1_audss_clk_probe,
+ .remove = sky1_audss_clk_remove,
+ .driver = {
+ .name = "sky1-audss-clk",
+ .suppress_bind_attrs = true,
+ .of_match_table = sky1_audss_clk_of_match,
+ .pm = &sky1_audss_clk_pm_ops,
+ },
+};
+module_platform_driver(sky1_audss_clk_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Joakim Zhang <joakim.zhang@cixtech.com>");
+MODULE_DESCRIPTION("Cixtech Sky1 Audio Subsystem Clock Controller Driver");
--
2.50.1
^ permalink raw reply related
* [PATCH v3 0/5] Add Cix Sky1 AUDSS clock and reset support
From: joakim.zhang @ 2026-06-10 7:56 UTC (permalink / raw)
To: mturquette, sboyd, bmasney, robh, krzk+dt, conor+dt, p.zabel,
gary.yang
Cc: cix-kernel-upstream, linux-clk, devicetree, linux-kernel,
linux-arm-kernel, Joakim Zhang
From: Joakim Zhang <joakim.zhang@cixtech.com>
This patch set adds the clock and reset support for AUDSS. The AUDSS groups
audio-related peripherals (HDA, I2S, DSP, DMA, mailboxes, watchdog, timer, etc.)
behind a single Clock and Reset Unit (CRU) register block.
Clock and reset changes normally belong to separate subsystems and would
ideally be submitted as independent series. They are combined here because the
AUDSS DT bindings cross-reference each other: the system-control binding
describes the clock child node, the clock binding documents reset lines exposed
on the parent syscon, and the DTS example wires both together. Keeping clock
and reset in one series gives reviewers the full picture when evaluating the
binding layout, dependencies, and integration.
Patches apply in the following order:
1. Reset support
- dt-bindings: soc: cix,sky1-system-control: add audss system control
- reset: cix: add audss support to sky1 reset driver
2. Clock support
- dt-bindings: clock: cix,sky1-audss-clock: add audss clock controller
- clk: cix: add sky1 audss clock controller
3. Device tree
- arm64: dts: cix: sky1: add audss system control
The reset and clock parts have each been build-tested and checked with
dt_binding_check independently. If reviewers prefer separate series for the
reset and clock maintainers, I can split and resubmit after this round of
review once the overall design is agreed on.
---
ChangeLogs:
v2->v3:
* clk part:
* devm_reset_control_get()->devm_reset_control_get_exclusive()
* assert noc reset from suspend
* clock parents changes from 6 to 4, and rename the clock names,
explain more about this: confirm with our designer, In fact,
there are 6 clock sources going into the audio subsystem. audio_clk1
and audio_clk3 are redundant in design and are not actually needed
in practice, so they are not shown here.
* refine clocks and clock-names property
* add detailed description of clocks
* drop parent node from clk binding
* drop define AUDSS_MAX_CLKS
* reset part:
* rename reset signal macro, remove _N
* drop SKY1_AUDSS_SW_RESET_NUM
* switching to compatible-style of defining subnodes in parent schema
v1->v2:
* remove audss_rst device node since it doesn't has resource, and
move to reset-sky1.c driver.
* remove hda related which would be sent after this patch set accepted
* soc componnet is okay by default from dtsi
* fix for audss clk driver:
* remove "comment "Clock options for Cixtech audss:""
* add select MFD_SYSCON
* move lock and clk_data into struct sky1_audss_clks_priv
* const char *name -> const char * const * name
* remove CLK_GET_RATE_NOCACHE
* divicer -> divider
* Reverse Christmas tree order
* return reg ? 1 : 0; -> return !!reg;
* return ERR_CAST(hw); -> return hw;
* of_device_get_match_data(dev) -> device_get_match_data()
* add lock from runtime_suspend/resume
* loop to more mailing lists
Joakim Zhang (5):
dt-bindings: soc: cix,sky1-system-control: add audss system control
reset: cix: add audss support to sky1 reset driver
dt-bindings: clock: cix,sky1-audss-clock: add audss clock controller
clk: cix: add sky1 audss clock controller
arm64: dts: cix: sky1: add audss system control
.../bindings/clock/cix,sky1-audss-clock.yaml | 80 ++
.../soc/cix/cix,sky1-system-control.yaml | 47 +-
arch/arm64/boot/dts/cix/sky1.dtsi | 24 +
drivers/clk/Kconfig | 1 +
drivers/clk/Makefile | 1 +
drivers/clk/cix/Kconfig | 16 +
drivers/clk/cix/Makefile | 3 +
drivers/clk/cix/clk-sky1-audss.c | 1175 +++++++++++++++++
drivers/reset/reset-sky1.c | 36 +-
include/dt-bindings/clock/cix,sky1-audss.h | 60 +
.../reset/cix,sky1-audss-system-control.h | 25 +
11 files changed, 1461 insertions(+), 7 deletions(-)
create mode 100644 Documentation/devicetree/bindings/clock/cix,sky1-audss-clock.yaml
create mode 100644 drivers/clk/cix/Kconfig
create mode 100644 drivers/clk/cix/Makefile
create mode 100644 drivers/clk/cix/clk-sky1-audss.c
create mode 100644 include/dt-bindings/clock/cix,sky1-audss.h
create mode 100644 include/dt-bindings/reset/cix,sky1-audss-system-control.h
--
2.50.1
^ permalink raw reply
* [PATCH v3 1/5] dt-bindings: soc: cix,sky1-system-control: add audss system control
From: joakim.zhang @ 2026-06-10 7:56 UTC (permalink / raw)
To: mturquette, sboyd, bmasney, robh, krzk+dt, conor+dt, p.zabel,
gary.yang
Cc: cix-kernel-upstream, linux-clk, devicetree, linux-kernel,
linux-arm-kernel, Joakim Zhang
In-Reply-To: <20260610075645.3581145-1-joakim.zhang@cixtech.com>
From: Joakim Zhang <joakim.zhang@cixtech.com>
The Cix Sky1 Audio Subsystem (AUDSS) groups audio-related clock, reset
and control registers in a dedicated CRU block. Software reset lines are
exposed on the syscon parent via #reset-cells, following the same model
as the existing Sky1 FCH and S5 system control bindings.
Add the cix,sky1-audss-system-control compatible to
cix,sky1-system-control.yaml for the MFD/syscon parent node, and define
AUDSS software reset indices in
include/dt-bindings/reset/cix,sky1-audss-system-control.h for I2S, HDA,
DMAC, mailbox, watchdog and timer blocks.
Signed-off-by: Joakim Zhang <joakim.zhang@cixtech.com>
---
.../soc/cix/cix,sky1-system-control.yaml | 52 +++++++++++++++++--
.../reset/cix,sky1-audss-system-control.h | 25 +++++++++
2 files changed, 72 insertions(+), 5 deletions(-)
create mode 100644 include/dt-bindings/reset/cix,sky1-audss-system-control.h
diff --git a/Documentation/devicetree/bindings/soc/cix/cix,sky1-system-control.yaml b/Documentation/devicetree/bindings/soc/cix/cix,sky1-system-control.yaml
index a01a515222c6..61d26a69fd44 100644
--- a/Documentation/devicetree/bindings/soc/cix/cix,sky1-system-control.yaml
+++ b/Documentation/devicetree/bindings/soc/cix/cix,sky1-system-control.yaml
@@ -15,11 +15,16 @@ description:
properties:
compatible:
- items:
- - enum:
- - cix,sky1-system-control
- - cix,sky1-s5-system-control
- - const: syscon
+ oneOf:
+ - items:
+ - enum:
+ - cix,sky1-system-control
+ - cix,sky1-s5-system-control
+ - const: syscon
+ - items:
+ - const: cix,sky1-audss-system-control
+ - const: simple-mfd
+ - const: syscon
reg:
maxItems: 1
@@ -27,6 +32,28 @@ properties:
'#reset-cells':
const: 1
+ clock-controller:
+ type: object
+ properties:
+ compatible:
+ const: cix,sky1-audss-clock
+ required:
+ - compatible
+ additionalProperties: true
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: cix,sky1-audss-system-control
+ then:
+ required:
+ - clock-controller
+ else:
+ properties:
+ clock-controller: false
+
required:
- compatible
- reg
@@ -40,3 +67,18 @@ examples:
reg = <0x4160000 0x100>;
#reset-cells = <1>;
};
+ - |
+ audss_syscon: system-controller@7110000 {
+ compatible = "cix,sky1-audss-system-control", "simple-mfd", "syscon";
+ reg = <0x7110000 0x10000>;
+ #reset-cells = <1>;
+
+ clock-controller {
+ compatible = "cix,sky1-audss-clock";
+ power-domains = <&smc_devpd 0>;
+ #clock-cells = <1>;
+ clocks = <&scmi_clk 0>, <&scmi_clk 2>, <&scmi_clk 4>, <&scmi_clk 5>;
+ clock-names = "x8k", "x11k", "sys", "48m";
+ resets = <&s5_syscon 31>;
+ };
+ };
diff --git a/include/dt-bindings/reset/cix,sky1-audss-system-control.h b/include/dt-bindings/reset/cix,sky1-audss-system-control.h
new file mode 100644
index 000000000000..aabdce60b094
--- /dev/null
+++ b/include/dt-bindings/reset/cix,sky1-audss-system-control.h
@@ -0,0 +1,25 @@
+/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */
+/*
+ * Copyright 2026 Cix Technology Group Co., Ltd.
+ */
+#ifndef DT_BINDING_RESET_CIX_SKY1_AUDSS_SYSTEM_CONTROL_H
+#define DT_BINDING_RESET_CIX_SKY1_AUDSS_SYSTEM_CONTROL_H
+
+#define AUDSS_I2S0_SW_RST 0
+#define AUDSS_I2S1_SW_RST 1
+#define AUDSS_I2S2_SW_RST 2
+#define AUDSS_I2S3_SW_RST 3
+#define AUDSS_I2S4_SW_RST 4
+#define AUDSS_I2S5_SW_RST 5
+#define AUDSS_I2S6_SW_RST 6
+#define AUDSS_I2S7_SW_RST 7
+#define AUDSS_I2S8_SW_RST 8
+#define AUDSS_I2S9_SW_RST 9
+#define AUDSS_WDT_SW_RST 10
+#define AUDSS_TIMER_SW_RST 11
+#define AUDSS_MB0_SW_RST 12
+#define AUDSS_MB1_SW_RST 13
+#define AUDSS_HDA_SW_RST 14
+#define AUDSS_DMAC_SW_RST 15
+
+#endif
--
2.50.1
^ permalink raw reply related
* [PATCH v3 2/5] reset: cix: add audss support to sky1 reset driver
From: joakim.zhang @ 2026-06-10 7:56 UTC (permalink / raw)
To: mturquette, sboyd, bmasney, robh, krzk+dt, conor+dt, p.zabel,
gary.yang
Cc: cix-kernel-upstream, linux-clk, devicetree, linux-kernel,
linux-arm-kernel, Joakim Zhang
In-Reply-To: <20260610075645.3581145-1-joakim.zhang@cixtech.com>
From: Joakim Zhang <joakim.zhang@cixtech.com>
Extend the Sky1 reset controller driver for the AUDSS CRU syscon. The
AUDSS block provides sixteen active-low software reset bits in one
register for audio subsystem peripherals.
Add a device tree match for cix,sky1-audss-system-control and the
corresponding reset signal table in reset-sky1.c, reusing the existing
regmap-based reset ops used by the FCH and S5 system control variants.
Signed-off-by: Joakim Zhang <joakim.zhang@cixtech.com>
---
drivers/reset/reset-sky1.c | 36 ++++++++++++++++++++++++++++++++++--
1 file changed, 34 insertions(+), 2 deletions(-)
diff --git a/drivers/reset/reset-sky1.c b/drivers/reset/reset-sky1.c
index 78e80a533c39..88100c631cee 100644
--- a/drivers/reset/reset-sky1.c
+++ b/drivers/reset/reset-sky1.c
@@ -16,6 +16,7 @@
#include <dt-bindings/reset/cix,sky1-system-control.h>
#include <dt-bindings/reset/cix,sky1-s5-system-control.h>
+#include <dt-bindings/reset/cix,sky1-audss-system-control.h>
#define SKY1_RESET_SLEEP_MIN_US 50
#define SKY1_RESET_SLEEP_MAX_US 100
@@ -258,6 +259,34 @@ static const struct sky1_src_variant variant_sky1_fch = {
.signals_num = ARRAY_SIZE(sky1_src_fch_signals),
};
+enum {
+ AUDSS_SW_RST = 0x78,
+};
+
+static const struct sky1_src_signal sky1_audss_signals[] = {
+ [AUDSS_I2S0_SW_RST] = { AUDSS_SW_RST, BIT(0) },
+ [AUDSS_I2S1_SW_RST] = { AUDSS_SW_RST, BIT(1) },
+ [AUDSS_I2S2_SW_RST] = { AUDSS_SW_RST, BIT(2) },
+ [AUDSS_I2S3_SW_RST] = { AUDSS_SW_RST, BIT(3) },
+ [AUDSS_I2S4_SW_RST] = { AUDSS_SW_RST, BIT(4) },
+ [AUDSS_I2S5_SW_RST] = { AUDSS_SW_RST, BIT(5) },
+ [AUDSS_I2S6_SW_RST] = { AUDSS_SW_RST, BIT(6) },
+ [AUDSS_I2S7_SW_RST] = { AUDSS_SW_RST, BIT(7) },
+ [AUDSS_I2S8_SW_RST] = { AUDSS_SW_RST, BIT(8) },
+ [AUDSS_I2S9_SW_RST] = { AUDSS_SW_RST, BIT(9) },
+ [AUDSS_WDT_SW_RST] = { AUDSS_SW_RST, BIT(10) },
+ [AUDSS_TIMER_SW_RST] = { AUDSS_SW_RST, BIT(11) },
+ [AUDSS_MB0_SW_RST] = { AUDSS_SW_RST, BIT(12) },
+ [AUDSS_MB1_SW_RST] = { AUDSS_SW_RST, BIT(13) },
+ [AUDSS_HDA_SW_RST] = { AUDSS_SW_RST, BIT(14) },
+ [AUDSS_DMAC_SW_RST] = { AUDSS_SW_RST, BIT(15) },
+};
+
+static const struct sky1_src_variant variant_sky1_audss = {
+ .signals = sky1_audss_signals,
+ .signals_num = ARRAY_SIZE(sky1_audss_signals),
+};
+
static struct sky1_src *to_sky1_src(struct reset_controller_dev *rcdev)
{
return container_of(rcdev, struct sky1_src, rcdev);
@@ -329,6 +358,8 @@ static int sky1_reset_probe(struct platform_device *pdev)
return -ENOMEM;
variant = of_device_get_match_data(dev);
+ if (!variant)
+ return -ENODEV;
sky1src->regmap = device_node_to_regmap(dev->of_node);
if (IS_ERR(sky1src->regmap)) {
@@ -347,8 +378,9 @@ static int sky1_reset_probe(struct platform_device *pdev)
}
static const struct of_device_id sky1_sysreg_of_match[] = {
- { .compatible = "cix,sky1-system-control", .data = &variant_sky1_fch},
- { .compatible = "cix,sky1-s5-system-control", .data = &variant_sky1},
+ { .compatible = "cix,sky1-system-control", .data = &variant_sky1_fch },
+ { .compatible = "cix,sky1-s5-system-control", .data = &variant_sky1 },
+ { .compatible = "cix,sky1-audss-system-control", .data = &variant_sky1_audss },
{},
};
MODULE_DEVICE_TABLE(of, sky1_sysreg_of_match);
--
2.50.1
^ permalink raw reply related
* [PATCH v3 5/5] arm64: dts: cix: sky1: add audss system control
From: joakim.zhang @ 2026-06-10 7:56 UTC (permalink / raw)
To: mturquette, sboyd, bmasney, robh, krzk+dt, conor+dt, p.zabel,
gary.yang
Cc: cix-kernel-upstream, linux-clk, devicetree, linux-kernel,
linux-arm-kernel, Joakim Zhang
In-Reply-To: <20260610075645.3581145-1-joakim.zhang@cixtech.com>
From: Joakim Zhang <joakim.zhang@cixtech.com>
Add audss system control device node, which would provides
clocks and resets for devices in audss domain.
Signed-off-by: Joakim Zhang <joakim.zhang@cixtech.com>
---
arch/arm64/boot/dts/cix/sky1.dtsi | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/arm64/boot/dts/cix/sky1.dtsi b/arch/arm64/boot/dts/cix/sky1.dtsi
index bb5cfb1f2113..368a1d85c93d 100644
--- a/arch/arm64/boot/dts/cix/sky1.dtsi
+++ b/arch/arm64/boot/dts/cix/sky1.dtsi
@@ -6,6 +6,10 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/cix,sky1.h>
+#include <dt-bindings/clock/cix,sky1-audss.h>
+#include <dt-bindings/reset/cix,sky1-system-control.h>
+#include <dt-bindings/reset/cix,sky1-s5-system-control.h>
+#include <dt-bindings/reset/cix,sky1-audss-system-control.h>
#include "sky1-power.h"
/ {
@@ -488,6 +492,26 @@ mbox_pm2ap: mailbox@65a0080 {
cix,mbox-dir = "rx";
};
+ audss_cru: system-controller@7110000 {
+ compatible = "cix,sky1-audss-system-control", "simple-mfd", "syscon";
+ reg = <0x0 0x07110000 0x0 0x10000>;
+ #reset-cells = <1>;
+ status = "okay";
+
+ audss_clk: clock-controller {
+ compatible = "cix,sky1-audss-clock";
+ power-domains = <&smc_devpd SKY1_PD_AUDIO>;
+ resets = <&s5_syscon SKY1_AUDIO_HIFI5_NOC_RESET_N>;
+ clocks = <&scmi_clk CLK_TREE_AUDIO_CLK0>,
+ <&scmi_clk CLK_TREE_AUDIO_CLK2>,
+ <&scmi_clk CLK_TREE_AUDIO_CLK4>,
+ <&scmi_clk CLK_TREE_AUDIO_CLK5>;
+ clock-names = "x8k", "x11k", "sys", "48m";
+ #clock-cells = <1>;
+ status = "okay";
+ };
+ };
+
mbox_sfh2ap: mailbox@8090000 {
compatible = "cix,sky1-mbox";
reg = <0x0 0x08090000 0x0 0x10000>;
--
2.50.1
^ permalink raw reply related
* Re: [PATCH v2 1/4] dt-bindings: remoteproc: imx_rproc: document optional "memory-region-names"
From: Krzysztof Kozlowski @ 2026-06-10 7:37 UTC (permalink / raw)
To: Laurentiu Mihalcea
Cc: Bjorn Andersson, Mathieu Poirier, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Sascha Hauer, Peng Fan,
Fabio Estevam, Daniel Baluta, Francesco Dolcini, linux-remoteproc,
devicetree, imx, linux-arm-kernel, linux-kernel
In-Reply-To: <20260605113621.1479-2-laurentiumihalcea111@gmail.com>
On Fri, Jun 05, 2026 at 04:36:18AM -0700, Laurentiu Mihalcea wrote:
> From: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
>
> The names of the carveout regions are derived using the names of the
> reserved memory devicetree nodes, which are referenced using the
> "memory-region" property. This adds a restriction on the names of said
> devicetree nodes, often bearing specific names such as: "vdevbuffer",
> "vdev0vring0", "rsc-table", etc... This goes against the devicetree
> specification's recommendation, which states that the devicetree node
> names should be generic.
No, it does not. Names like rsc-table feels exactly like DT spec is
asking - for a name matching purpose. Are you sure you read the spec?
>
> Fix this by documenting an additional, optional property:
> "memory-region-names". This way, the carveout names can use the values
> passed via "memory-region-names", while keeping the devicetree node
> names of the reserved memory regions generic.
I don't see how anything here is fixed. memory-region-names has nothing
to do with node names.
Best regards,
Krzysztof
^ permalink raw reply
* Re: [PATCH v6 04/20] dma-pool: track decrypted atomic pools and select them via attrs
From: Aneesh Kumar K.V @ 2026-06-10 8:07 UTC (permalink / raw)
To: Jason Gunthorpe
Cc: iommu, linux-arm-kernel, linux-kernel, linux-coco, Robin Murphy,
Marek Szyprowski, Will Deacon, Marc Zyngier, Steven Price,
Suzuki K Poulose, Catalin Marinas, Jiri Pirko, Mostafa Saleh,
Petr Tesarik, Alexey Kardashevskiy, Dan Williams, Xu Yilun,
linuxppc-dev, linux-s390, Madhavan Srinivasan, Michael Ellerman,
Nicholas Piggin, Christophe Leroy (CS GROUP), Alexander Gordeev,
Gerald Schaefer, Heiko Carstens, Vasily Gorbik,
Christian Borntraeger, Sven Schnelle, x86, Jiri Pirko,
Michael Kelley
In-Reply-To: <20260609143242.GK2764304@ziepe.ca>
Jason Gunthorpe <jgg@ziepe.ca> writes:
> On Thu, Jun 04, 2026 at 02:09:43PM +0530, Aneesh Kumar K.V (Arm) wrote:
>> struct page *dma_alloc_from_pool(struct device *dev, size_t size,
>> - void **cpu_addr, gfp_t gfp,
>> + void **cpu_addr, gfp_t gfp, unsigned long attrs,
>> bool (*phys_addr_ok)(struct device *, phys_addr_t, size_t))
>> {
>> - struct gen_pool *pool = NULL;
>> + struct dma_gen_pool *dma_pool = NULL;
>> struct page *page;
>> bool pool_found = false;
>>
>> - while ((pool = dma_guess_pool(pool, gfp))) {
>> + while ((dma_pool = dma_guess_pool(dma_pool, gfp))) {
>> +
>> + if (dma_pool->unencrypted != !!(attrs & DMA_ATTR_CC_SHARED))
>> + continue;
>
> I don't think you should be overloading DMA_ATTR_CC_SHARED like this.
>
> /*
> * DMA_ATTR_CC_SHARED is not a caller-visible dma_alloc_*()
> * attribute. The direct allocator uses it internally after it has
> * decided that the backing pages must be shared/decrypted, so the
> * rest of the allocation path can consistently select DMA addresses,
> * choose compatible pools and restore encryption on free.
> */
> if (attrs & DMA_ATTR_CC_SHARED)
> return NULL;
>
> if (force_dma_unencrypted(dev)) {
> attrs |= DMA_ATTR_CC_SHARED;
> mark_mem_decrypt = true;
> }
>
> It is fine to have a bit inside the attrs that is only used by the
> internal logic, but it needs to have a clearer name
> __DMA_ATTR_REQUIRE_CC_SHARED perhaps.
>
Are you suggesting adding another attribute in addition to
DMA_ATTR_CC_SHARED?
Is the idea that __DMA_ATTR_REQUIRE_CC_SHARED would be used in the
allocation path to request a CC_SHARED allocation, while
DMA_ATTR_CC_SHARED would be used in the mapping path to describe the
attribute of the address?
>
> The sashiko note does look legit though:
>
> if (IS_ENABLED(CONFIG_DMA_DIRECT_REMAP) &&
> !gfpflags_allow_blocking(gfp) && !coherent) {
> page = dma_alloc_from_pool(dev, PAGE_ALIGN(size), &cpu_addr,
> gfp, attrs, NULL);
> if (!page)
> return NULL;
>
> I don't see anything doing the force_dma_unencrypted test along this
> callchain..
>
> I guess it should be done one step up in dma_alloc_attrs() instead of
> in dma_direct_alloc()?
>
Yes, I'll move it there.
-aneesh
^ permalink raw reply
* [PATCH v8 10/10] arm64: dts: realtek: Add clock support for RTD1625
From: Yu-Chun Lin @ 2026-06-10 8:08 UTC (permalink / raw)
To: mturquette, sboyd, robh, krzk+dt, conor+dt, p.zabel, cylee12,
afaerber, jyanchou
Cc: bmasney, devicetree, linux-clk, linux-kernel, linux-arm-kernel,
linux-realtek-soc, james.tai, cy.huang, stanley_chang,
eleanor.lin
In-Reply-To: <20260610080824.255063-1-eleanor.lin@realtek.com>
Add the clock controller nodes and osc27m fixed clock for the
Realtek RTD1625 SoC.
Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com>
---
Changes in v8:
- Sort device nodes by unit address.
---
arch/arm64/boot/dts/realtek/kent.dtsi | 33 +++++++++++++++++++++++++++
1 file changed, 33 insertions(+)
diff --git a/arch/arm64/boot/dts/realtek/kent.dtsi b/arch/arm64/boot/dts/realtek/kent.dtsi
index ae006ce24420..69f28cb35585 100644
--- a/arch/arm64/boot/dts/realtek/kent.dtsi
+++ b/arch/arm64/boot/dts/realtek/kent.dtsi
@@ -26,6 +26,15 @@ timer {
<GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
};
+ clocks {
+ osc27m: osc {
+ compatible = "fixed-clock";
+ clock-frequency = <27000000>;
+ clock-output-names = "osc27m";
+ #clock-cells = <0>;
+ };
+ };
+
cpus {
#address-cells = <1>;
#size-cells = <0>;
@@ -141,6 +150,22 @@ rbus: bus@98000000 {
#address-cells = <1>;
#size-cells = <1>;
+ cc: clock-controller@0 {
+ compatible = "realtek,rtd1625-crt-clk";
+ reg = <0x0 0x900>;
+ clocks = <&osc27m>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ ic: clock-controller@7088 {
+ compatible = "realtek,rtd1625-iso-clk";
+ reg = <0x7088 0x8>;
+ clocks = <&osc27m>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
uart0: serial@7800 {
compatible = "snps,dw-apb-uart";
reg = <0x7800 0x100>;
@@ -150,6 +175,14 @@ uart0: serial@7800 {
reg-shift = <2>;
status = "disabled";
};
+
+ iso_s_cc: clock-controller@146310 {
+ compatible = "realtek,rtd1625-iso-s-clk";
+ reg = <0x146310 0x8>;
+ clocks = <&osc27m>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
};
gic: interrupt-controller@ff100000 {
--
2.43.0
^ permalink raw reply related
* [PATCH v8 00/10] clk: realtek: Add RTD1625 clock support
From: Yu-Chun Lin @ 2026-06-10 8:08 UTC (permalink / raw)
To: mturquette, sboyd, robh, krzk+dt, conor+dt, p.zabel, cylee12,
afaerber, jyanchou
Cc: bmasney, devicetree, linux-clk, linux-kernel, linux-arm-kernel,
linux-realtek-soc, james.tai, cy.huang, stanley_chang,
eleanor.lin
Hello,
This patch series adds clock support for Realtek's RTD1625 platform.
The series includes:
1. Device Tree: Add clock controller nodes.
2. Infrastructure: reset controller, basic clocks, PLLs, gate clocks, mux
clocks, and MMC-tuned PLLs.
3. Platform drivers: two clock controller drivers for RTD1625-CRT and
RTD1625-ISO.
Best regards,
Yu-Chun Lin
---
Changes in v8:
Patch 3:
- Add depends on RESET_CONTROLLER and select MFD_SYSCON for config
RTK_CLK_COMMON
- Fix error handling for devm_auxiliary_device_create()
Patch 4:
- Reduce the timeout value in regmap_read_poll_timeout_atomic() from 2000ms to
500ms to avoid prolonged busy-waiting and prevent triggering the NMI Watchdog
- Remove 'freq_ready_valid' and add comments to clarify that register offset 0
is never a valid address on Realtek SoCs, meaning it is not configured
- Add the missing spin_unlock_irqrestore() when regmap_read() fails
Patch 6:
- In clk_regmap_mux_get_parent(), return 0xff instead of 0 to properly indicate
an error
- In clk_regmap_mux_set_parent(), cast index to u32 to avoid signed integer
- overflow
Patch 7:
- Fix the mask shift in set_phrt0()
- For better safety and readability, modify pointer comparison for phase_id
- In clk_pll_mmc_recalc_rate(), return 0 instead of an error code upon failure
Patch 8 & 9:
- Remove the trailing NULL element ([RTD1625_XX_CLK_MAX] = NULL) from the
clk_hw_onecell_data arrays
- Add MODULE_DEVICE_TABLE(of, ...) for the tristate config
- Add '.suppress_bind_attrs = true', to avoid handling pointer problem, cause
clock should not allow to manually disable by users
- Fix a typo
Patch 10:
- Sort device nodes by unit address
v7: https://lore.kernel.org/lkml/20260508111641.3192177-1-eleanor.lin@realtek.com/
Cheng-Yu Lee (8):
reset: Add Realtek basic reset support
clk: realtek: Introduce a common probe()
clk: realtek: Add support for phase locked loops (PLLs)
clk: realtek: Add support for gate clock
clk: realtek: Add support for mux clock
clk: realtek: Add support for MMC-tuned PLL clocks
clk: realtek: Add RTD1625-CRT clock controller driver
clk: realtek: Add RTD1625-ISO clock controller driver
Yu-Chun Lin (2):
dt-bindings: clock: Add Realtek RTD1625 Clock & Reset Controller
arm64: dts: realtek: Add clock support for RTD1625
.../bindings/clock/realtek,rtd1625-clk.yaml | 58 ++
MAINTAINERS | 20 +
arch/arm64/boot/dts/realtek/kent.dtsi | 33 +
drivers/clk/Kconfig | 1 +
drivers/clk/Makefile | 1 +
drivers/clk/realtek/Kconfig | 48 ++
drivers/clk/realtek/Makefile | 13 +
drivers/clk/realtek/clk-pll-mmc.c | 459 ++++++++++
drivers/clk/realtek/clk-pll.c | 209 +++++
drivers/clk/realtek/clk-pll.h | 60 ++
drivers/clk/realtek/clk-regmap-gate.c | 70 ++
drivers/clk/realtek/clk-regmap-gate.h | 65 ++
drivers/clk/realtek/clk-regmap-mux.c | 41 +
drivers/clk/realtek/clk-regmap-mux.h | 43 +
drivers/clk/realtek/clk-rtd1625-crt.c | 792 ++++++++++++++++++
drivers/clk/realtek/clk-rtd1625-iso.c | 151 ++++
drivers/clk/realtek/common.c | 66 ++
drivers/clk/realtek/common.h | 37 +
drivers/clk/realtek/freq_table.c | 38 +
drivers/clk/realtek/freq_table.h | 16 +
drivers/reset/Kconfig | 1 +
drivers/reset/Makefile | 1 +
drivers/reset/realtek/Kconfig | 19 +
drivers/reset/realtek/Makefile | 3 +
drivers/reset/realtek/common.c | 90 ++
drivers/reset/realtek/common.h | 29 +
drivers/reset/realtek/reset-rtd1625-crt.c | 187 +++++
drivers/reset/realtek/reset-rtd1625-iso.c | 99 +++
.../dt-bindings/clock/realtek,rtd1625-clk.h | 164 ++++
include/dt-bindings/reset/realtek,rtd1625.h | 171 ++++
30 files changed, 2985 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/realtek,rtd1625-clk.yaml
create mode 100644 drivers/clk/realtek/Kconfig
create mode 100644 drivers/clk/realtek/Makefile
create mode 100644 drivers/clk/realtek/clk-pll-mmc.c
create mode 100644 drivers/clk/realtek/clk-pll.c
create mode 100644 drivers/clk/realtek/clk-pll.h
create mode 100644 drivers/clk/realtek/clk-regmap-gate.c
create mode 100644 drivers/clk/realtek/clk-regmap-gate.h
create mode 100644 drivers/clk/realtek/clk-regmap-mux.c
create mode 100644 drivers/clk/realtek/clk-regmap-mux.h
create mode 100644 drivers/clk/realtek/clk-rtd1625-crt.c
create mode 100644 drivers/clk/realtek/clk-rtd1625-iso.c
create mode 100644 drivers/clk/realtek/common.c
create mode 100644 drivers/clk/realtek/common.h
create mode 100644 drivers/clk/realtek/freq_table.c
create mode 100644 drivers/clk/realtek/freq_table.h
create mode 100644 drivers/reset/realtek/Kconfig
create mode 100644 drivers/reset/realtek/Makefile
create mode 100644 drivers/reset/realtek/common.c
create mode 100644 drivers/reset/realtek/common.h
create mode 100644 drivers/reset/realtek/reset-rtd1625-crt.c
create mode 100644 drivers/reset/realtek/reset-rtd1625-iso.c
create mode 100644 include/dt-bindings/clock/realtek,rtd1625-clk.h
create mode 100644 include/dt-bindings/reset/realtek,rtd1625.h
--
2.43.0
^ permalink raw reply
* [PATCH v8 08/10] clk: realtek: Add RTD1625-CRT clock controller driver
From: Yu-Chun Lin @ 2026-06-10 8:08 UTC (permalink / raw)
To: mturquette, sboyd, robh, krzk+dt, conor+dt, p.zabel, cylee12,
afaerber, jyanchou
Cc: bmasney, devicetree, linux-clk, linux-kernel, linux-arm-kernel,
linux-realtek-soc, james.tai, cy.huang, stanley_chang,
eleanor.lin
In-Reply-To: <20260610080824.255063-1-eleanor.lin@realtek.com>
From: Cheng-Yu Lee <cylee12@realtek.com>
Add support for the CRT (Clock, Reset, and Test) domain clock controller
on the Realtek RTD1625 SoC. This driver provides essential clock sources
(including PLLs), gating, and multiplexing functionalities for the
platform's peripherals.
Since the reset controller shares the same register space with the CRT
clock controller, it is instantiated as an auxiliary device by the core
clock driver. This patch also includes the corresponding auxiliary reset
driver to handle the CRT domain resets.
Signed-off-by: Cheng-Yu Lee <cylee12@realtek.com>
Co-developed-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com>
---
Changes in v8:
- Remove the trailing NULL element ([RTD1625_CRT_CLK_MAX] = NULL) from the
clk_hw_onecell_data arrays.
- Add MODULE_DEVICE_TABLE(of, ...) for the tristate config.
- Add '.suppress_bind_attrs = true' to avoid handling pointer problem, cause
clock should not allow to manually disable by users.
- Fix a typo.
---
drivers/clk/realtek/Kconfig | 15 +
drivers/clk/realtek/Makefile | 1 +
drivers/clk/realtek/clk-rtd1625-crt.c | 792 ++++++++++++++++++++++
drivers/reset/realtek/Kconfig | 11 +
drivers/reset/realtek/Makefile | 1 +
drivers/reset/realtek/reset-rtd1625-crt.c | 187 +++++
6 files changed, 1007 insertions(+)
create mode 100644 drivers/clk/realtek/clk-rtd1625-crt.c
create mode 100644 drivers/reset/realtek/reset-rtd1625-crt.c
diff --git a/drivers/clk/realtek/Kconfig b/drivers/clk/realtek/Kconfig
index 5a832fc3228a..acfbe95014f4 100644
--- a/drivers/clk/realtek/Kconfig
+++ b/drivers/clk/realtek/Kconfig
@@ -30,4 +30,19 @@ config RTK_CLK_COMMON
config RTK_CLK_PLL_MMC
tristate
+config CLK_RTD1625
+ tristate "RTD1625 Clock Controller"
+ depends on RESET_CONTROLLER
+ select RESET_RTD1625
+ select RTK_CLK_COMMON
+ select RTK_CLK_PLL_MMC
+ help
+ Support for the clock controller on Realtek RTD1625 SoCs.
+
+ This driver provides clock sources, gating, multiplexing, and
+ reset control for peripherals on the RTD1625 platform.
+
+ Say Y here if your system is based on the RTD1625 and you need
+ its peripheral devices to function.
+
endif
diff --git a/drivers/clk/realtek/Makefile b/drivers/clk/realtek/Makefile
index fd7d777902c8..f4a62be092d2 100644
--- a/drivers/clk/realtek/Makefile
+++ b/drivers/clk/realtek/Makefile
@@ -9,3 +9,4 @@ clk-rtk-y += clk-regmap-mux.o
clk-rtk-y += freq_table.o
clk-rtk-$(CONFIG_RTK_CLK_PLL_MMC) += clk-pll-mmc.o
+obj-$(CONFIG_CLK_RTD1625) += clk-rtd1625-crt.o
diff --git a/drivers/clk/realtek/clk-rtd1625-crt.c b/drivers/clk/realtek/clk-rtd1625-crt.c
new file mode 100644
index 000000000000..6fa1c1f0d4f3
--- /dev/null
+++ b/drivers/clk/realtek/clk-rtd1625-crt.c
@@ -0,0 +1,792 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2022-2026 Realtek Semiconductor Corporation
+ * Author: Cheng-Yu Lee <cylee12@realtek.com>
+ */
+
+#include <dt-bindings/clock/realtek,rtd1625-clk.h>
+#include <linux/array_size.h>
+#include <linux/bits.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/spinlock.h>
+#include "clk-pll.h"
+#include "clk-regmap-gate.h"
+#include "clk-regmap-mux.h"
+
+#define RTD1625_CRT_CLK_MAX 172
+#define RTD1625_CRT_RSTN_MAX 123
+
+#define RTD1625_REG_PLL_ACPU1 0x10c
+#define RTD1625_REG_PLL_ACPU2 0x110
+#define RTD1625_REG_PLL_SSC_DIG_ACPU0 0x5c0
+#define RTD1625_REG_PLL_SSC_DIG_ACPU1 0x5c4
+#define RTD1625_REG_PLL_SSC_DIG_ACPU2 0x5c8
+#define RTD1625_REG_PLL_SSC_DIG_ACPU_DBG2 0x5dc
+
+#define RTD1625_REG_PLL_VE1_1 0x114
+#define RTD1625_REG_PLL_VE1_2 0x118
+#define RTD1625_REG_PLL_SSC_DIG_VE1_0 0x580
+#define RTD1625_REG_PLL_SSC_DIG_VE1_1 0x584
+#define RTD1625_REG_PLL_SSC_DIG_VE1_2 0x588
+#define RTD1625_REG_PLL_SSC_DIG_VE1_DBG2 0x59c
+
+#define RTD1625_REG_PLL_GPU1 0x1c0
+#define RTD1625_REG_PLL_GPU2 0x1c4
+#define RTD1625_REG_PLL_SSC_DIG_GPU0 0x5a0
+#define RTD1625_REG_PLL_SSC_DIG_GPU1 0x5a4
+#define RTD1625_REG_PLL_SSC_DIG_GPU2 0x5a8
+#define RTD1625_REG_PLL_SSC_DIG_GPU_DBG2 0x5bc
+
+#define RTD1625_REG_PLL_NPU1 0x1c8
+#define RTD1625_REG_PLL_NPU2 0x1cc
+#define RTD1625_REG_PLL_SSC_DIG_NPU0 0x800
+#define RTD1625_REG_PLL_SSC_DIG_NPU1 0x804
+#define RTD1625_REG_PLL_SSC_DIG_NPU2 0x808
+#define RTD1625_REG_PLL_SSC_DIG_NPU_DBG2 0x81c
+
+#define RTD1625_REG_PLL_VE2_1 0x1d0
+#define RTD1625_REG_PLL_VE2_2 0x1d4
+#define RTD1625_REG_PLL_SSC_DIG_VE2_0 0x5e0
+#define RTD1625_REG_PLL_SSC_DIG_VE2_1 0x5e4
+#define RTD1625_REG_PLL_SSC_DIG_VE2_2 0x5e8
+#define RTD1625_REG_PLL_SSC_DIG_VE2_DBG2 0x5fc
+
+#define RTD1625_REG_PLL_HIFI1 0x1d8
+#define RTD1625_REG_PLL_HIFI2 0x1dc
+#define RTD1625_REG_PLL_SSC_DIG_HIFI0 0x6e0
+#define RTD1625_REG_PLL_SSC_DIG_HIFI1 0x6e4
+#define RTD1625_REG_PLL_SSC_DIG_HIFI2 0x6e8
+#define RTD1625_REG_PLL_SSC_DIG_HIFI_DBG2 0x6fc
+
+#define RTD1625_REG_PLL_BUS1 0x524
+
+#define RTD1625_REG_PLL_SSC_DIG_DDSA1 0x564
+
+#define RTD1625_REG_PLL_SSC_DIG_DCSB1 0x544
+
+static const char * const clk_gpu_parents[] = {"pll_gpu", "clk_sys"};
+static CLK_REGMAP_MUX(clk_gpu, clk_gpu_parents, CLK_SET_RATE_PARENT | CLK_SET_RATE_NO_REPARENT,
+ 0x28, 12, 0x1);
+static const char * const clk_ve_parents[] = {"pll_vo", "clk_sysh", "pll_ve1", "pll_ve2"};
+static CLK_REGMAP_MUX(clk_ve1, clk_ve_parents, CLK_SET_RATE_PARENT | CLK_SET_RATE_NO_REPARENT,
+ 0x4c, 0, 0x3);
+static CLK_REGMAP_MUX(clk_ve2, clk_ve_parents, CLK_SET_RATE_PARENT | CLK_SET_RATE_NO_REPARENT,
+ 0x4c, 3, 0x3);
+static CLK_REGMAP_MUX(clk_ve4, clk_ve_parents, CLK_SET_RATE_PARENT | CLK_SET_RATE_NO_REPARENT,
+ 0x4c, 6, 0x3);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_misc, CLK_IS_CRITICAL, 0x50, 0, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_pcie0, 0, 0x50, 2, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_gspi, 0, 0x50, 6, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_iso_misc, 0, 0x50, 10, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_sds, 0, 0x50, 12, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_hdmi, 0, 0x50, 14, 1);
+static CLK_REGMAP_GATE(clk_en_gpu, "clk_gpu", CLK_SET_RATE_PARENT, 0x50, 18, 1);
+static CLK_REGMAP_GATE(clk_en_ve1, "clk_ve1", CLK_SET_RATE_PARENT, 0x50, 20, 1);
+static CLK_REGMAP_GATE(clk_en_ve2, "clk_ve2", CLK_SET_RATE_PARENT, 0x50, 22, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_se, 0, 0x50, 30, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_md, 0, 0x54, 4, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_tp, CLK_IS_CRITICAL, 0x54, 6, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_rcic, 0, 0x54, 8, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_nf, 0, 0x54, 10, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_emmc, 0, 0x54, 12, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_sd, 0, 0x54, 14, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_sdio_ip, 0, 0x54, 16, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_mipi_csi, 0, 0x54, 18, 1);
+static CLK_REGMAP_GATE(clk_en_emmc_ip, "pll_emmc", CLK_SET_RATE_PARENT, 0x54, 20, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_sdio, 0, 0x54, 22, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_sd_ip, 0, 0x54, 24, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_tpb, 0, 0x54, 28, 1);
+static CLK_REGMAP_GATE(clk_en_misc_sc1, "clk_en_misc", 0, 0x54, 30, 1);
+static CLK_REGMAP_GATE(clk_en_misc_i2c_3, "clk_en_misc", 0, 0x58, 0, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_jpeg, 0, 0x58, 4, 1);
+static CLK_REGMAP_GATE(clk_en_acpu, "pll_acpu", CLK_SET_RATE_PARENT,
+ 0x58, 6, 1);
+static CLK_REGMAP_GATE(clk_en_misc_sc0, "clk_en_misc", 0, 0x58, 10, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_hdmirx, 0, 0x58, 26, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_hse, CLK_IS_CRITICAL, 0x58, 28, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_fan, 0, 0x5c, 2, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_sata_wrap_sys, 0, 0x5c, 8, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_sata_wrap_sysh, 0, 0x5c, 10, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_sata_mac_sysh, 0, 0x5c, 12, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_r2rdsc, 0, 0x5c, 14, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_pcie1, 0, 0x5c, 18, 1);
+static CLK_REGMAP_GATE(clk_en_misc_i2c_4, "clk_en_misc", 0, 0x5c, 20, 1);
+static CLK_REGMAP_GATE(clk_en_misc_i2c_5, "clk_en_misc", 0, 0x5c, 22, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_tsio, 0, 0x5c, 24, 1);
+static CLK_REGMAP_GATE(clk_en_ve4, "clk_ve4", CLK_SET_RATE_PARENT,
+ 0x5c, 26, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_edp, 0, 0x5c, 28, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_tsio_trx, 0, 0x5c, 30, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_pcie2, 0, 0x8c, 0, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_earc, 0, 0x8c, 4, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_lite, 0, 0x8c, 6, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_mipi_dsi, 0, 0x8c, 8, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_npupp, 0, 0x8c, 10, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_npu, 0, 0x8c, 12, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_aucpu0, 0, 0x8c, 14, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_aucpu1, 0, 0x8c, 16, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_nsram, 0, 0x8c, 18, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_hdmitop, 0, 0x8c, 20, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_aucpu_iso_npu, 0, 0x8c, 24, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_keyladder, 0, 0x8c, 26, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_ifcp_klm, 0, 0x8c, 28, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_ifcp, 0, 0x8c, 30, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_mdl_genpw, 0, 0xb0, 0, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_mdl_chip, 0, 0xb0, 2, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_mdl_ip, 0, 0xb0, 4, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_mdlm2m, 0, 0xb0, 6, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_mdl_xtal, 0, 0xb0, 8, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_test_mux, 0, 0xb0, 10, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_dla, 0, 0xb0, 12, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_tpcw, 0, 0xb0, 16, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_gpu_ts_src, 0, 0xb0, 18, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_vi, 0, 0xb0, 22, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_lvds1, 0, 0xb0, 24, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_lvds2, 0, 0xb0, 26, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_aucpu, 0, 0xb0, 28, 1);
+static CLK_REGMAP_GATE(clk_en_ur1, "clk_en_ur_top", 0, 0x884, 0, 1);
+static CLK_REGMAP_GATE(clk_en_ur2, "clk_en_ur_top", 0, 0x884, 2, 1);
+static CLK_REGMAP_GATE(clk_en_ur3, "clk_en_ur_top", 0, 0x884, 4, 1);
+static CLK_REGMAP_GATE(clk_en_ur4, "clk_en_ur_top", 0, 0x884, 6, 1);
+static CLK_REGMAP_GATE(clk_en_ur5, "clk_en_ur_top", 0, 0x884, 8, 1);
+static CLK_REGMAP_GATE(clk_en_ur6, "clk_en_ur_top", 0, 0x884, 10, 1);
+static CLK_REGMAP_GATE(clk_en_ur7, "clk_en_ur_top", 0, 0x884, 12, 1);
+static CLK_REGMAP_GATE(clk_en_ur8, "clk_en_ur_top", 0, 0x884, 14, 1);
+static CLK_REGMAP_GATE(clk_en_ur9, "clk_en_ur_top", 0, 0x884, 16, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_ur_top, CLK_IS_CRITICAL, 0x884, 18, 1);
+static CLK_REGMAP_GATE(clk_en_misc_i2c_7, "clk_en_misc", 0, 0x884, 28, 1);
+static CLK_REGMAP_GATE(clk_en_misc_i2c_6, "clk_en_misc", 0, 0x884, 30, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_spi0, 0, 0x894, 0, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_spi1, 0, 0x894, 2, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_spi2, 0, 0x894, 4, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_lsadc0, 0, 0x894, 16, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_lsadc1, 0, 0x894, 18, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_isomis_dma, 0, 0x894, 20, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_dptx, 0, 0x894, 24, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_npu_mipi_csi, 0, 0x894, 26, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_edptx, 0, 0x894, 28, 1);
+
+#define FREQ_NF_MASK 0x7ffff
+#define FREQ_NF(_r, _nf) {.rate = _r, .val = (_nf),}
+
+static const struct freq_table acpu_tbl[] = {
+ FREQ_NF(513000000, 0x11000),
+ FREQ_TABLE_END
+};
+
+static const struct freq_table ve_tbl[] = {
+ FREQ_NF(553500000, 0x12800),
+ FREQ_NF(661500000, 0x16800),
+ FREQ_NF(688500000, 0x17800),
+ FREQ_TABLE_END
+};
+
+static const struct freq_table bus_tbl[] = {
+ FREQ_NF(513000000, 0x11000),
+ FREQ_NF(540000000, 0x12000),
+ FREQ_NF(553500000, 0x12800),
+ FREQ_TABLE_END
+};
+
+static const struct freq_table ddsa_tbl[] = {
+ FREQ_NF(432000000, 0xe000),
+ FREQ_TABLE_END
+};
+
+static const struct freq_table gpu_tbl[] = {
+ FREQ_NF(405000000, 0xd000),
+ FREQ_NF(540000000, 0x12000),
+ FREQ_NF(661500000, 0x16800),
+ FREQ_NF(729000000, 0x19000),
+ FREQ_NF(810000000, 0x1c000),
+ FREQ_NF(850500000, 0x1d800),
+ FREQ_TABLE_END
+};
+
+static const struct freq_table hifi_tbl[] = {
+ FREQ_NF(756000000, 0x1a000),
+ FREQ_NF(810000000, 0x1c000),
+ FREQ_TABLE_END
+};
+
+static const struct freq_table npu_tbl[] = {
+ FREQ_NF(661500000, 0x16800),
+ FREQ_NF(729000000, 0x19000),
+ FREQ_NF(810000000, 0x1c000),
+ FREQ_TABLE_END
+};
+
+static const struct reg_sequence pll_acpu_seq_power_on[] = {
+ {RTD1625_REG_PLL_ACPU2, 0x5},
+ {RTD1625_REG_PLL_ACPU2, 0x7},
+ {RTD1625_REG_PLL_ACPU1, 0x54000},
+ {RTD1625_REG_PLL_SSC_DIG_ACPU2, 0x1e1f8e},
+ {RTD1625_REG_PLL_SSC_DIG_ACPU0, 0x4},
+ {RTD1625_REG_PLL_SSC_DIG_ACPU0, 0x5, 200},
+ {RTD1625_REG_PLL_ACPU2, 0x3},
+};
+
+static const struct reg_sequence pll_acpu_seq_power_off[] = {
+ {RTD1625_REG_PLL_ACPU2, 0x4},
+};
+
+static const struct reg_sequence pll_acpu_seq_pre_set_freq[] = {
+ {RTD1625_REG_PLL_SSC_DIG_ACPU0, 0x4},
+};
+
+static const struct reg_sequence pll_acpu_seq_post_set_freq[] = {
+ {RTD1625_REG_PLL_SSC_DIG_ACPU0, 0x5},
+};
+
+static struct clk_pll pll_acpu = {
+ .clkr.hw.init = CLK_HW_INIT("pll_acpu", "osc27m", &rtk_clk_pll_ops, CLK_GET_RATE_NOCACHE),
+ .seq_power_on = pll_acpu_seq_power_on,
+ .num_seq_power_on = ARRAY_SIZE(pll_acpu_seq_power_on),
+ .seq_power_off = pll_acpu_seq_power_off,
+ .num_seq_power_off = ARRAY_SIZE(pll_acpu_seq_power_off),
+ .seq_pre_set_freq = pll_acpu_seq_pre_set_freq,
+ .num_seq_pre_set_freq = ARRAY_SIZE(pll_acpu_seq_pre_set_freq),
+ .seq_post_set_freq = pll_acpu_seq_post_set_freq,
+ .num_seq_post_set_freq = ARRAY_SIZE(pll_acpu_seq_post_set_freq),
+ .freq_reg = RTD1625_REG_PLL_SSC_DIG_ACPU1,
+ .freq_tbl = acpu_tbl,
+ .freq_mask = FREQ_NF_MASK,
+ .freq_ready_reg = RTD1625_REG_PLL_SSC_DIG_ACPU_DBG2,
+ .freq_ready_mask = BIT(20),
+ .freq_ready_val = BIT(20),
+ .power_reg = RTD1625_REG_PLL_ACPU2,
+ .power_mask = 0x7,
+ .power_val_on = 0x3,
+ .lock = __SPIN_LOCK_UNLOCKED(pll_acpu.lock),
+};
+
+static const struct reg_sequence pll_ve1_seq_power_on[] = {
+ {RTD1625_REG_PLL_VE1_2, 0x5},
+ {RTD1625_REG_PLL_VE1_2, 0x7},
+ {RTD1625_REG_PLL_VE1_1, 0x54000},
+ {RTD1625_REG_PLL_SSC_DIG_VE1_0, 0x4},
+ {RTD1625_REG_PLL_SSC_DIG_VE1_0, 0x5, 200},
+ {RTD1625_REG_PLL_VE1_2, 0x3},
+};
+
+static const struct reg_sequence pll_ve1_seq_power_off[] = {
+ {RTD1625_REG_PLL_VE1_2, 0x4},
+};
+
+static const struct reg_sequence pll_ve1_seq_pre_set_freq[] = {
+ {RTD1625_REG_PLL_SSC_DIG_VE1_0, 0x4},
+};
+
+static const struct reg_sequence pll_ve1_seq_post_set_freq[] = {
+ {RTD1625_REG_PLL_SSC_DIG_VE1_0, 0x5},
+};
+
+static struct clk_pll pll_ve1 = {
+ .clkr.hw.init = CLK_HW_INIT("pll_ve1", "osc27m", &rtk_clk_pll_ops, CLK_GET_RATE_NOCACHE),
+ .seq_power_on = pll_ve1_seq_power_on,
+ .num_seq_power_on = ARRAY_SIZE(pll_ve1_seq_power_on),
+ .seq_power_off = pll_ve1_seq_power_off,
+ .num_seq_power_off = ARRAY_SIZE(pll_ve1_seq_power_off),
+ .seq_pre_set_freq = pll_ve1_seq_pre_set_freq,
+ .num_seq_pre_set_freq = ARRAY_SIZE(pll_ve1_seq_pre_set_freq),
+ .seq_post_set_freq = pll_ve1_seq_post_set_freq,
+ .num_seq_post_set_freq = ARRAY_SIZE(pll_ve1_seq_post_set_freq),
+ .freq_reg = RTD1625_REG_PLL_SSC_DIG_VE1_1,
+ .freq_tbl = ve_tbl,
+ .freq_mask = FREQ_NF_MASK,
+ .freq_ready_reg = RTD1625_REG_PLL_SSC_DIG_VE1_DBG2,
+ .freq_ready_mask = BIT(20),
+ .freq_ready_val = BIT(20),
+ .power_reg = RTD1625_REG_PLL_VE1_2,
+ .power_mask = 0x7,
+ .power_val_on = 0x3,
+ .lock = __SPIN_LOCK_UNLOCKED(pll_ve1.lock),
+};
+
+static struct clk_pll pll_ddsa = {
+ .clkr.hw.init = CLK_HW_INIT("pll_ddsa", "osc27m", &rtk_clk_pll_ro_ops,
+ CLK_GET_RATE_NOCACHE),
+ .freq_reg = RTD1625_REG_PLL_SSC_DIG_DDSA1,
+ .freq_tbl = ddsa_tbl,
+ .freq_mask = FREQ_NF_MASK,
+ .lock = __SPIN_LOCK_UNLOCKED(pll_ddsa.lock),
+};
+
+static struct clk_pll pll_bus = {
+ .clkr.hw.init = CLK_HW_INIT("pll_bus", "osc27m", &rtk_clk_pll_ro_ops,
+ CLK_GET_RATE_NOCACHE),
+ .freq_reg = RTD1625_REG_PLL_BUS1,
+ .freq_tbl = bus_tbl,
+ .freq_mask = FREQ_NF_MASK,
+ .lock = __SPIN_LOCK_UNLOCKED(pll_bus.lock),
+};
+
+static CLK_FIXED_FACTOR(clk_sys, "clk_sys", "pll_bus", 2, 1, 0);
+
+static struct clk_pll pll_dcsb = {
+ .clkr.hw.init = CLK_HW_INIT("pll_dcsb", "osc27m", &rtk_clk_pll_ro_ops,
+ CLK_GET_RATE_NOCACHE),
+ .freq_reg = RTD1625_REG_PLL_SSC_DIG_DCSB1,
+ .freq_tbl = bus_tbl,
+ .freq_mask = FREQ_NF_MASK,
+ .lock = __SPIN_LOCK_UNLOCKED(pll_dcsb.lock),
+};
+
+static CLK_FIXED_FACTOR(clk_sysh, "clk_sysh", "pll_dcsb", 1, 1, 0);
+
+static const struct reg_sequence pll_gpu_seq_power_on[] = {
+ {RTD1625_REG_PLL_GPU2, 0x5},
+ {RTD1625_REG_PLL_GPU2, 0x7},
+ {RTD1625_REG_PLL_GPU1, 0x54000},
+ {RTD1625_REG_PLL_SSC_DIG_GPU0, 0x4},
+ {RTD1625_REG_PLL_SSC_DIG_GPU0, 0x5, 200},
+ {RTD1625_REG_PLL_GPU2, 0x3},
+};
+
+static const struct reg_sequence pll_gpu_seq_power_off[] = {
+ {RTD1625_REG_PLL_GPU2, 0x4},
+};
+
+static const struct reg_sequence pll_gpu_seq_pre_set_freq[] = {
+ {RTD1625_REG_PLL_SSC_DIG_GPU0, 0x4},
+};
+
+static const struct reg_sequence pll_gpu_seq_post_set_freq[] = {
+ {RTD1625_REG_PLL_SSC_DIG_GPU0, 0x5},
+};
+
+static struct clk_pll pll_gpu = {
+ .clkr.hw.init = CLK_HW_INIT("pll_gpu", "osc27m", &rtk_clk_pll_ops, CLK_GET_RATE_NOCACHE),
+ .seq_power_on = pll_gpu_seq_power_on,
+ .num_seq_power_on = ARRAY_SIZE(pll_gpu_seq_power_on),
+ .seq_power_off = pll_gpu_seq_power_off,
+ .num_seq_power_off = ARRAY_SIZE(pll_gpu_seq_power_off),
+ .seq_pre_set_freq = pll_gpu_seq_pre_set_freq,
+ .num_seq_pre_set_freq = ARRAY_SIZE(pll_gpu_seq_pre_set_freq),
+ .seq_post_set_freq = pll_gpu_seq_post_set_freq,
+ .num_seq_post_set_freq = ARRAY_SIZE(pll_gpu_seq_post_set_freq),
+ .freq_reg = RTD1625_REG_PLL_SSC_DIG_GPU1,
+ .freq_tbl = gpu_tbl,
+ .freq_mask = FREQ_NF_MASK,
+ .freq_ready_reg = RTD1625_REG_PLL_SSC_DIG_GPU_DBG2,
+ .freq_ready_mask = BIT(20),
+ .freq_ready_val = BIT(20),
+ .power_reg = RTD1625_REG_PLL_GPU2,
+ .power_mask = 0x7,
+ .power_val_on = 0x3,
+ .lock = __SPIN_LOCK_UNLOCKED(pll_gpu.lock),
+};
+
+static const struct reg_sequence pll_npu_seq_power_on[] = {
+ {RTD1625_REG_PLL_NPU2, 0x5},
+ {RTD1625_REG_PLL_NPU2, 0x7},
+ {RTD1625_REG_PLL_NPU1, 0x54000},
+ {RTD1625_REG_PLL_SSC_DIG_NPU0, 0x4},
+ {RTD1625_REG_PLL_SSC_DIG_NPU0, 0x5, 200},
+ {RTD1625_REG_PLL_NPU2, 0x3},
+};
+
+static const struct reg_sequence pll_npu_seq_power_off[] = {
+ {RTD1625_REG_PLL_NPU2, 0x4},
+ {RTD1625_REG_PLL_NPU1, 0x54010},
+};
+
+static const struct reg_sequence pll_npu_seq_pre_set_freq[] = {
+ {RTD1625_REG_PLL_SSC_DIG_NPU0, 0x4},
+};
+
+static const struct reg_sequence pll_npu_seq_post_set_freq[] = {
+ {RTD1625_REG_PLL_SSC_DIG_NPU0, 0x5},
+};
+
+static struct clk_pll pll_npu = {
+ .clkr.hw.init = CLK_HW_INIT("pll_npu", "osc27m", &rtk_clk_pll_ops,
+ CLK_GET_RATE_NOCACHE),
+ .seq_power_on = pll_npu_seq_power_on,
+ .num_seq_power_on = ARRAY_SIZE(pll_npu_seq_power_on),
+ .seq_power_off = pll_npu_seq_power_off,
+ .num_seq_power_off = ARRAY_SIZE(pll_npu_seq_power_off),
+ .seq_pre_set_freq = pll_npu_seq_pre_set_freq,
+ .num_seq_pre_set_freq = ARRAY_SIZE(pll_npu_seq_pre_set_freq),
+ .seq_post_set_freq = pll_npu_seq_post_set_freq,
+ .num_seq_post_set_freq = ARRAY_SIZE(pll_npu_seq_post_set_freq),
+ .freq_reg = RTD1625_REG_PLL_SSC_DIG_NPU1,
+ .freq_tbl = npu_tbl,
+ .freq_mask = FREQ_NF_MASK,
+ .freq_ready_reg = RTD1625_REG_PLL_SSC_DIG_NPU_DBG2,
+ .freq_ready_mask = BIT(20),
+ .freq_ready_val = BIT(20),
+ .power_reg = RTD1625_REG_PLL_NPU2,
+ .power_mask = 0x7,
+ .power_val_on = 0x3,
+ .lock = __SPIN_LOCK_UNLOCKED(pll_npu.lock),
+};
+
+static CLK_FIXED_FACTOR(clk_npu, "clk_npu", "pll_npu", 1, 1, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR(clk_npu_mipi_csi, "clk_npu_mipi_csi", "pll_npu", 1, 1,
+ CLK_SET_RATE_PARENT);
+
+static const struct reg_sequence pll_ve2_seq_power_on[] = {
+ {RTD1625_REG_PLL_VE2_2, 0x5},
+ {RTD1625_REG_PLL_VE2_2, 0x7},
+ {RTD1625_REG_PLL_VE2_1, 0x54000},
+ {RTD1625_REG_PLL_SSC_DIG_VE2_0, 0x4},
+ {RTD1625_REG_PLL_SSC_DIG_VE2_0, 0x5, 200},
+ {RTD1625_REG_PLL_VE2_2, 0x3},
+};
+
+static const struct reg_sequence pll_ve2_seq_power_off[] = {
+ {RTD1625_REG_PLL_VE2_2, 0x4},
+};
+
+static const struct reg_sequence pll_ve2_seq_pre_set_freq[] = {
+ {RTD1625_REG_PLL_SSC_DIG_VE2_0, 0x4},
+};
+
+static const struct reg_sequence pll_ve2_seq_post_set_freq[] = {
+ {RTD1625_REG_PLL_SSC_DIG_VE2_0, 0x5},
+};
+
+static struct clk_pll pll_ve2 = {
+ .clkr.hw.init = CLK_HW_INIT("pll_ve2", "osc27m", &rtk_clk_pll_ops, CLK_GET_RATE_NOCACHE),
+ .seq_power_on = pll_ve2_seq_power_on,
+ .num_seq_power_on = ARRAY_SIZE(pll_ve2_seq_power_on),
+ .seq_power_off = pll_ve2_seq_power_off,
+ .num_seq_power_off = ARRAY_SIZE(pll_ve2_seq_power_off),
+ .seq_pre_set_freq = pll_ve2_seq_pre_set_freq,
+ .num_seq_pre_set_freq = ARRAY_SIZE(pll_ve2_seq_pre_set_freq),
+ .seq_post_set_freq = pll_ve2_seq_post_set_freq,
+ .num_seq_post_set_freq = ARRAY_SIZE(pll_ve2_seq_post_set_freq),
+ .freq_reg = RTD1625_REG_PLL_SSC_DIG_VE2_1,
+ .freq_tbl = ve_tbl,
+ .freq_mask = FREQ_NF_MASK,
+ .freq_ready_reg = RTD1625_REG_PLL_SSC_DIG_VE2_DBG2,
+ .freq_ready_mask = BIT(20),
+ .freq_ready_val = BIT(20),
+ .power_reg = RTD1625_REG_PLL_VE2_2,
+ .power_mask = 0x7,
+ .power_val_on = 0x3,
+ .lock = __SPIN_LOCK_UNLOCKED(pll_ve2.lock),
+};
+
+static const struct reg_sequence pll_hifi_seq_power_on[] = {
+ {RTD1625_REG_PLL_HIFI2, 0x5},
+ {RTD1625_REG_PLL_HIFI2, 0x7},
+ {RTD1625_REG_PLL_HIFI1, 0x54000},
+ {RTD1625_REG_PLL_SSC_DIG_HIFI0, 0x4},
+ {RTD1625_REG_PLL_SSC_DIG_HIFI0, 0x5, 200},
+ {RTD1625_REG_PLL_HIFI2, 0x3},
+};
+
+static const struct reg_sequence pll_hifi_seq_power_off[] = {
+ {RTD1625_REG_PLL_HIFI2, 0x4},
+};
+
+static const struct reg_sequence pll_hifi_seq_pre_set_freq[] = {
+ {RTD1625_REG_PLL_SSC_DIG_HIFI0, 0x4},
+};
+
+static const struct reg_sequence pll_hifi_seq_post_set_freq[] = {
+ {RTD1625_REG_PLL_SSC_DIG_HIFI0, 0x5},
+};
+
+static struct clk_pll pll_hifi = {
+ .clkr.hw.init = CLK_HW_INIT("pll_hifi", "osc27m", &rtk_clk_pll_ops, CLK_GET_RATE_NOCACHE),
+ .seq_power_on = pll_hifi_seq_power_on,
+ .num_seq_power_on = ARRAY_SIZE(pll_hifi_seq_power_on),
+ .seq_power_off = pll_hifi_seq_power_off,
+ .num_seq_power_off = ARRAY_SIZE(pll_hifi_seq_power_off),
+ .seq_pre_set_freq = pll_hifi_seq_pre_set_freq,
+ .num_seq_pre_set_freq = ARRAY_SIZE(pll_hifi_seq_pre_set_freq),
+ .seq_post_set_freq = pll_hifi_seq_post_set_freq,
+ .num_seq_post_set_freq = ARRAY_SIZE(pll_hifi_seq_post_set_freq),
+ .freq_reg = RTD1625_REG_PLL_SSC_DIG_HIFI1,
+ .freq_tbl = hifi_tbl,
+ .freq_mask = FREQ_NF_MASK,
+ .freq_ready_reg = RTD1625_REG_PLL_SSC_DIG_HIFI_DBG2,
+ .freq_ready_mask = BIT(20),
+ .freq_ready_val = BIT(20),
+ .power_reg = RTD1625_REG_PLL_HIFI2,
+ .power_mask = 0x7,
+ .power_val_on = 0x3,
+ .lock = __SPIN_LOCK_UNLOCKED(pll_hifi.lock),
+};
+
+static CLK_FIXED_FACTOR(pll_emmc_ref, "pll_emmc_ref", "osc27m", 1, 1, 0);
+
+static struct clk_pll_mmc pll_emmc = {
+ .pll_ofs = 0x1f0,
+ .ssc_dig_ofs = 0x6b0,
+ .clkr.hw.init = CLK_HW_INIT("pll_emmc", "pll_emmc_ref", &rtk_clk_pll_mmc_ops, 0),
+ .phase0_hw.init = CLK_HW_INIT("pll_emmc_vp0", "pll_emmc", &rtk_clk_pll_mmc_phase_ops, 0),
+ .phase1_hw.init = CLK_HW_INIT("pll_emmc_vp1", "pll_emmc", &rtk_clk_pll_mmc_phase_ops, 0),
+};
+
+static struct clk_regmap * const rtd1625_crt_regmap_clks[] = {
+ &clk_en_misc.clkr,
+ &clk_en_pcie0.clkr,
+ &clk_en_gspi.clkr,
+ &clk_en_iso_misc.clkr,
+ &clk_en_sds.clkr,
+ &clk_en_hdmi.clkr,
+ &clk_en_gpu.clkr,
+ &clk_en_ve1.clkr,
+ &clk_en_ve2.clkr,
+ &clk_en_se.clkr,
+ &clk_en_md.clkr,
+ &clk_en_tp.clkr,
+ &clk_en_rcic.clkr,
+ &clk_en_nf.clkr,
+ &clk_en_emmc.clkr,
+ &clk_en_sd.clkr,
+ &clk_en_sdio_ip.clkr,
+ &clk_en_mipi_csi.clkr,
+ &clk_en_emmc_ip.clkr,
+ &clk_en_sdio.clkr,
+ &clk_en_sd_ip.clkr,
+ &clk_en_tpb.clkr,
+ &clk_en_misc_sc1.clkr,
+ &clk_en_misc_i2c_3.clkr,
+ &clk_en_jpeg.clkr,
+ &clk_en_acpu.clkr,
+ &clk_en_misc_sc0.clkr,
+ &clk_en_hdmirx.clkr,
+ &clk_en_hse.clkr,
+ &clk_en_fan.clkr,
+ &clk_en_sata_wrap_sys.clkr,
+ &clk_en_sata_wrap_sysh.clkr,
+ &clk_en_sata_mac_sysh.clkr,
+ &clk_en_r2rdsc.clkr,
+ &clk_en_pcie1.clkr,
+ &clk_en_misc_i2c_4.clkr,
+ &clk_en_misc_i2c_5.clkr,
+ &clk_en_tsio.clkr,
+ &clk_en_ve4.clkr,
+ &clk_en_edp.clkr,
+ &clk_en_tsio_trx.clkr,
+ &clk_en_pcie2.clkr,
+ &clk_en_earc.clkr,
+ &clk_en_lite.clkr,
+ &clk_en_mipi_dsi.clkr,
+ &clk_en_npupp.clkr,
+ &clk_en_npu.clkr,
+ &clk_en_aucpu0.clkr,
+ &clk_en_aucpu1.clkr,
+ &clk_en_nsram.clkr,
+ &clk_en_hdmitop.clkr,
+ &clk_en_aucpu_iso_npu.clkr,
+ &clk_en_keyladder.clkr,
+ &clk_en_ifcp_klm.clkr,
+ &clk_en_ifcp.clkr,
+ &clk_en_mdl_genpw.clkr,
+ &clk_en_mdl_chip.clkr,
+ &clk_en_mdl_ip.clkr,
+ &clk_en_mdlm2m.clkr,
+ &clk_en_mdl_xtal.clkr,
+ &clk_en_test_mux.clkr,
+ &clk_en_dla.clkr,
+ &clk_en_tpcw.clkr,
+ &clk_en_gpu_ts_src.clkr,
+ &clk_en_vi.clkr,
+ &clk_en_lvds1.clkr,
+ &clk_en_lvds2.clkr,
+ &clk_en_aucpu.clkr,
+ &clk_en_ur1.clkr,
+ &clk_en_ur2.clkr,
+ &clk_en_ur3.clkr,
+ &clk_en_ur4.clkr,
+ &clk_en_ur5.clkr,
+ &clk_en_ur6.clkr,
+ &clk_en_ur7.clkr,
+ &clk_en_ur8.clkr,
+ &clk_en_ur9.clkr,
+ &clk_en_ur_top.clkr,
+ &clk_en_misc_i2c_7.clkr,
+ &clk_en_misc_i2c_6.clkr,
+ &clk_en_spi0.clkr,
+ &clk_en_spi1.clkr,
+ &clk_en_spi2.clkr,
+ &clk_en_lsadc0.clkr,
+ &clk_en_lsadc1.clkr,
+ &clk_en_isomis_dma.clkr,
+ &clk_en_dptx.clkr,
+ &clk_en_npu_mipi_csi.clkr,
+ &clk_en_edptx.clkr,
+ &clk_gpu.clkr,
+ &clk_ve1.clkr,
+ &clk_ve2.clkr,
+ &clk_ve4.clkr,
+ &pll_ve1.clkr,
+ &pll_ddsa.clkr,
+ &pll_bus.clkr,
+ &pll_dcsb.clkr,
+ &pll_gpu.clkr,
+ &pll_npu.clkr,
+ &pll_ve2.clkr,
+ &pll_hifi.clkr,
+ &pll_emmc.clkr,
+ &pll_acpu.clkr,
+};
+
+static struct clk_hw_onecell_data rtd1625_crt_hw_data = {
+ .num = RTD1625_CRT_CLK_MAX,
+ .hws = {
+ [RTD1625_CRT_CLK_EN_MISC] = &__clk_regmap_gate_hw(&clk_en_misc),
+ [RTD1625_CRT_CLK_EN_PCIE0] = &__clk_regmap_gate_hw(&clk_en_pcie0),
+ [RTD1625_CRT_CLK_EN_GSPI] = &__clk_regmap_gate_hw(&clk_en_gspi),
+ [RTD1625_CRT_CLK_EN_ISO_MISC] = &__clk_regmap_gate_hw(&clk_en_iso_misc),
+ [RTD1625_CRT_CLK_EN_SDS] = &__clk_regmap_gate_hw(&clk_en_sds),
+ [RTD1625_CRT_CLK_EN_HDMI] = &__clk_regmap_gate_hw(&clk_en_hdmi),
+ [RTD1625_CRT_CLK_EN_GPU] = &__clk_regmap_gate_hw(&clk_en_gpu),
+ [RTD1625_CRT_CLK_EN_VE1] = &__clk_regmap_gate_hw(&clk_en_ve1),
+ [RTD1625_CRT_CLK_EN_VE2] = &__clk_regmap_gate_hw(&clk_en_ve2),
+ [RTD1625_CRT_CLK_EN_MD] = &__clk_regmap_gate_hw(&clk_en_md),
+ [RTD1625_CRT_CLK_EN_TP] = &__clk_regmap_gate_hw(&clk_en_tp),
+ [RTD1625_CRT_CLK_EN_RCIC] = &__clk_regmap_gate_hw(&clk_en_rcic),
+ [RTD1625_CRT_CLK_EN_NF] = &__clk_regmap_gate_hw(&clk_en_nf),
+ [RTD1625_CRT_CLK_EN_EMMC] = &__clk_regmap_gate_hw(&clk_en_emmc),
+ [RTD1625_CRT_CLK_EN_SD] = &__clk_regmap_gate_hw(&clk_en_sd),
+ [RTD1625_CRT_CLK_EN_SDIO_IP] = &__clk_regmap_gate_hw(&clk_en_sdio_ip),
+ [RTD1625_CRT_CLK_EN_MIPI_CSI] = &__clk_regmap_gate_hw(&clk_en_mipi_csi),
+ [RTD1625_CRT_CLK_EN_EMMC_IP] = &__clk_regmap_gate_hw(&clk_en_emmc_ip),
+ [RTD1625_CRT_CLK_EN_SDIO] = &__clk_regmap_gate_hw(&clk_en_sdio),
+ [RTD1625_CRT_CLK_EN_SD_IP] = &__clk_regmap_gate_hw(&clk_en_sd_ip),
+ [RTD1625_CRT_CLK_EN_TPB] = &__clk_regmap_gate_hw(&clk_en_tpb),
+ [RTD1625_CRT_CLK_EN_MISC_SC1] = &__clk_regmap_gate_hw(&clk_en_misc_sc1),
+ [RTD1625_CRT_CLK_EN_MISC_I2C_3] = &__clk_regmap_gate_hw(&clk_en_misc_i2c_3),
+ [RTD1625_CRT_CLK_EN_ACPU] = &__clk_regmap_gate_hw(&clk_en_acpu),
+ [RTD1625_CRT_CLK_EN_JPEG] = &__clk_regmap_gate_hw(&clk_en_jpeg),
+ [RTD1625_CRT_CLK_EN_MISC_SC0] = &__clk_regmap_gate_hw(&clk_en_misc_sc0),
+ [RTD1625_CRT_CLK_EN_HDMIRX] = &__clk_regmap_gate_hw(&clk_en_hdmirx),
+ [RTD1625_CRT_CLK_EN_HSE] = &__clk_regmap_gate_hw(&clk_en_hse),
+ [RTD1625_CRT_CLK_EN_FAN] = &__clk_regmap_gate_hw(&clk_en_fan),
+ [RTD1625_CRT_CLK_EN_SATA_WRAP_SYS] = &__clk_regmap_gate_hw(&clk_en_sata_wrap_sys),
+ [RTD1625_CRT_CLK_EN_SATA_WRAP_SYSH] = &__clk_regmap_gate_hw(&clk_en_sata_wrap_sysh),
+ [RTD1625_CRT_CLK_EN_SATA_MAC_SYSH] = &__clk_regmap_gate_hw(&clk_en_sata_mac_sysh),
+ [RTD1625_CRT_CLK_EN_R2RDSC] = &__clk_regmap_gate_hw(&clk_en_r2rdsc),
+ [RTD1625_CRT_CLK_EN_PCIE1] = &__clk_regmap_gate_hw(&clk_en_pcie1),
+ [RTD1625_CRT_CLK_EN_MISC_I2C_4] = &__clk_regmap_gate_hw(&clk_en_misc_i2c_4),
+ [RTD1625_CRT_CLK_EN_MISC_I2C_5] = &__clk_regmap_gate_hw(&clk_en_misc_i2c_5),
+ [RTD1625_CRT_CLK_EN_TSIO] = &__clk_regmap_gate_hw(&clk_en_tsio),
+ [RTD1625_CRT_CLK_EN_VE4] = &__clk_regmap_gate_hw(&clk_en_ve4),
+ [RTD1625_CRT_CLK_EN_EDP] = &__clk_regmap_gate_hw(&clk_en_edp),
+ [RTD1625_CRT_CLK_EN_TSIO_TRX] = &__clk_regmap_gate_hw(&clk_en_tsio_trx),
+ [RTD1625_CRT_CLK_EN_PCIE2] = &__clk_regmap_gate_hw(&clk_en_pcie2),
+ [RTD1625_CRT_CLK_EN_EARC] = &__clk_regmap_gate_hw(&clk_en_earc),
+ [RTD1625_CRT_CLK_EN_LITE] = &__clk_regmap_gate_hw(&clk_en_lite),
+ [RTD1625_CRT_CLK_EN_MIPI_DSI] = &__clk_regmap_gate_hw(&clk_en_mipi_dsi),
+ [RTD1625_CRT_CLK_EN_NPUPP] = &__clk_regmap_gate_hw(&clk_en_npupp),
+ [RTD1625_CRT_CLK_EN_NPU] = &__clk_regmap_gate_hw(&clk_en_npu),
+ [RTD1625_CRT_CLK_EN_AUCPU0] = &__clk_regmap_gate_hw(&clk_en_aucpu0),
+ [RTD1625_CRT_CLK_EN_AUCPU1] = &__clk_regmap_gate_hw(&clk_en_aucpu1),
+ [RTD1625_CRT_CLK_EN_NSRAM] = &__clk_regmap_gate_hw(&clk_en_nsram),
+ [RTD1625_CRT_CLK_EN_HDMITOP] = &__clk_regmap_gate_hw(&clk_en_hdmitop),
+ [RTD1625_CRT_CLK_EN_AUCPU_ISO_NPU] = &__clk_regmap_gate_hw(&clk_en_aucpu_iso_npu),
+ [RTD1625_CRT_CLK_EN_KEYLADDER] = &__clk_regmap_gate_hw(&clk_en_keyladder),
+ [RTD1625_CRT_CLK_EN_IFCP_KLM] = &__clk_regmap_gate_hw(&clk_en_ifcp_klm),
+ [RTD1625_CRT_CLK_EN_IFCP] = &__clk_regmap_gate_hw(&clk_en_ifcp),
+ [RTD1625_CRT_CLK_EN_MDL_GENPW] = &__clk_regmap_gate_hw(&clk_en_mdl_genpw),
+ [RTD1625_CRT_CLK_EN_MDL_CHIP] = &__clk_regmap_gate_hw(&clk_en_mdl_chip),
+ [RTD1625_CRT_CLK_EN_MDL_IP] = &__clk_regmap_gate_hw(&clk_en_mdl_ip),
+ [RTD1625_CRT_CLK_EN_MDLM2M] = &__clk_regmap_gate_hw(&clk_en_mdlm2m),
+ [RTD1625_CRT_CLK_EN_MDL_XTAL] = &__clk_regmap_gate_hw(&clk_en_mdl_xtal),
+ [RTD1625_CRT_CLK_EN_TEST_MUX] = &__clk_regmap_gate_hw(&clk_en_test_mux),
+ [RTD1625_CRT_CLK_EN_DLA] = &__clk_regmap_gate_hw(&clk_en_dla),
+ [RTD1625_CRT_CLK_EN_TPCW] = &__clk_regmap_gate_hw(&clk_en_tpcw),
+ [RTD1625_CRT_CLK_EN_GPU_TS_SRC] = &__clk_regmap_gate_hw(&clk_en_gpu_ts_src),
+ [RTD1625_CRT_CLK_EN_VI] = &__clk_regmap_gate_hw(&clk_en_vi),
+ [RTD1625_CRT_CLK_EN_LVDS1] = &__clk_regmap_gate_hw(&clk_en_lvds1),
+ [RTD1625_CRT_CLK_EN_LVDS2] = &__clk_regmap_gate_hw(&clk_en_lvds2),
+ [RTD1625_CRT_CLK_EN_AUCPU] = &__clk_regmap_gate_hw(&clk_en_aucpu),
+ [RTD1625_CRT_CLK_EN_UR1] = &__clk_regmap_gate_hw(&clk_en_ur1),
+ [RTD1625_CRT_CLK_EN_UR2] = &__clk_regmap_gate_hw(&clk_en_ur2),
+ [RTD1625_CRT_CLK_EN_UR3] = &__clk_regmap_gate_hw(&clk_en_ur3),
+ [RTD1625_CRT_CLK_EN_UR4] = &__clk_regmap_gate_hw(&clk_en_ur4),
+ [RTD1625_CRT_CLK_EN_UR5] = &__clk_regmap_gate_hw(&clk_en_ur5),
+ [RTD1625_CRT_CLK_EN_UR6] = &__clk_regmap_gate_hw(&clk_en_ur6),
+ [RTD1625_CRT_CLK_EN_UR7] = &__clk_regmap_gate_hw(&clk_en_ur7),
+ [RTD1625_CRT_CLK_EN_UR8] = &__clk_regmap_gate_hw(&clk_en_ur8),
+ [RTD1625_CRT_CLK_EN_UR9] = &__clk_regmap_gate_hw(&clk_en_ur9),
+ [RTD1625_CRT_CLK_EN_UR_TOP] = &__clk_regmap_gate_hw(&clk_en_ur_top),
+ [RTD1625_CRT_CLK_EN_MISC_I2C_7] = &__clk_regmap_gate_hw(&clk_en_misc_i2c_7),
+ [RTD1625_CRT_CLK_EN_MISC_I2C_6] = &__clk_regmap_gate_hw(&clk_en_misc_i2c_6),
+ [RTD1625_CRT_CLK_EN_SPI0] = &__clk_regmap_gate_hw(&clk_en_spi0),
+ [RTD1625_CRT_CLK_EN_SPI1] = &__clk_regmap_gate_hw(&clk_en_spi1),
+ [RTD1625_CRT_CLK_EN_SPI2] = &__clk_regmap_gate_hw(&clk_en_spi2),
+ [RTD1625_CRT_CLK_EN_LSADC0] = &__clk_regmap_gate_hw(&clk_en_lsadc0),
+ [RTD1625_CRT_CLK_EN_LSADC1] = &__clk_regmap_gate_hw(&clk_en_lsadc1),
+ [RTD1625_CRT_CLK_EN_ISOMIS_DMA] = &__clk_regmap_gate_hw(&clk_en_isomis_dma),
+ [RTD1625_CRT_CLK_EN_DPTX] = &__clk_regmap_gate_hw(&clk_en_dptx),
+ [RTD1625_CRT_CLK_EN_NPU_MIPI_CSI] = &__clk_regmap_gate_hw(&clk_en_npu_mipi_csi),
+ [RTD1625_CRT_CLK_EN_EDPTX] = &__clk_regmap_gate_hw(&clk_en_edptx),
+ [RTD1625_CRT_CLK_GPU] = &__clk_regmap_mux_hw(&clk_gpu),
+ [RTD1625_CRT_CLK_VE1] = &__clk_regmap_mux_hw(&clk_ve1),
+ [RTD1625_CRT_CLK_VE2] = &__clk_regmap_mux_hw(&clk_ve2),
+ [RTD1625_CRT_CLK_VE4] = &__clk_regmap_mux_hw(&clk_ve4),
+ [RTD1625_CRT_PLL_VE1] = &__clk_pll_hw(&pll_ve1),
+ [RTD1625_CRT_PLL_DDSA] = &__clk_pll_hw(&pll_ddsa),
+ [RTD1625_CRT_PLL_BUS] = &__clk_pll_hw(&pll_bus),
+ [RTD1625_CRT_CLK_SYS] = &clk_sys.hw,
+ [RTD1625_CRT_PLL_DCSB] = &__clk_pll_hw(&pll_dcsb),
+ [RTD1625_CRT_CLK_SYSH] = &clk_sysh.hw,
+ [RTD1625_CRT_PLL_GPU] = &__clk_pll_hw(&pll_gpu),
+ [RTD1625_CRT_PLL_NPU] = &__clk_pll_hw(&pll_npu),
+ [RTD1625_CRT_PLL_VE2] = &__clk_pll_hw(&pll_ve2),
+ [RTD1625_CRT_PLL_HIFI] = &__clk_pll_hw(&pll_hifi),
+ [RTD1625_CRT_PLL_EMMC_REF] = &pll_emmc_ref.hw,
+ [RTD1625_CRT_PLL_EMMC] = &__clk_pll_mmc_hw(&pll_emmc),
+ [RTD1625_CRT_PLL_EMMC_VP0] = &pll_emmc.phase0_hw,
+ [RTD1625_CRT_PLL_EMMC_VP1] = &pll_emmc.phase1_hw,
+ [RTD1625_CRT_PLL_ACPU] = &__clk_pll_hw(&pll_acpu),
+ [RTD1625_CRT_CLK_NPU] = &clk_npu.hw,
+ [RTD1625_CRT_CLK_NPU_MIPI_CSI] = &clk_npu_mipi_csi.hw,
+ [RTD1625_CRT_CLK_MAX - 1] = NULL,
+ },
+};
+
+static const struct rtk_clk_desc rtd1625_crt_desc = {
+ .clk_data = &rtd1625_crt_hw_data,
+ .clks = rtd1625_crt_regmap_clks,
+ .num_clks = ARRAY_SIZE(rtd1625_crt_regmap_clks),
+};
+
+static int rtd1625_crt_probe(struct platform_device *pdev)
+{
+ const struct rtk_clk_desc *desc;
+
+ desc = of_device_get_match_data(&pdev->dev);
+ if (!desc)
+ return -EINVAL;
+
+ return rtk_clk_probe(pdev, desc, "crt_rst");
+}
+
+static const struct of_device_id rtd1625_crt_match[] = {
+ {.compatible = "realtek,rtd1625-crt-clk", .data = &rtd1625_crt_desc,},
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, rtd1625_crt_match);
+
+static struct platform_driver rtd1625_crt_driver = {
+ .probe = rtd1625_crt_probe,
+ .driver = {
+ .name = "rtk-rtd1625-crt-clk",
+ .of_match_table = rtd1625_crt_match,
+ .suppress_bind_attrs = true,
+ },
+};
+
+static int __init rtd1625_crt_init(void)
+{
+ return platform_driver_register(&rtd1625_crt_driver);
+}
+subsys_initcall(rtd1625_crt_init);
+
+MODULE_DESCRIPTION("Realtek RTD1625 CRT Clock Controller Driver");
+MODULE_AUTHOR("Cheng-Yu Lee <cylee12@realtek.com>");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS("REALTEK_CLK");
diff --git a/drivers/reset/realtek/Kconfig b/drivers/reset/realtek/Kconfig
index bb6dd856a64a..b122e6334508 100644
--- a/drivers/reset/realtek/Kconfig
+++ b/drivers/reset/realtek/Kconfig
@@ -6,3 +6,14 @@ config RESET_RTK_COMMON
Realtek SoCs. It provides shared reset control operations
(assert, deassert, status) and a registration helper function
that other Realtek-specific reset drivers can use.
+
+config RESET_RTD1625
+ tristate "RTD1625 Reset Controller"
+ depends on ARCH_REALTEK || COMPILE_TEST
+ select RESET_RTK_COMMON
+ select AUXILIARY_BUS
+ help
+ This enables the reset controller driver for Realtek RTD1625 SoC.
+ The driver controls reset lines for various peripherals including
+ PCIe, SATA, HDMI, display, video encoder/decoder, USB, SD, audio,
+ and other subsystems.
diff --git a/drivers/reset/realtek/Makefile b/drivers/reset/realtek/Makefile
index b59a3f7f2453..65c29a12524d 100644
--- a/drivers/reset/realtek/Makefile
+++ b/drivers/reset/realtek/Makefile
@@ -1,2 +1,3 @@
# SPDX-License-Identifier: GPL-2.0-only
obj-$(CONFIG_RESET_RTK_COMMON) += common.o
+obj-$(CONFIG_RESET_RTD1625) += reset-rtd1625-crt.o
diff --git a/drivers/reset/realtek/reset-rtd1625-crt.c b/drivers/reset/realtek/reset-rtd1625-crt.c
new file mode 100644
index 000000000000..9de0e9808f7c
--- /dev/null
+++ b/drivers/reset/realtek/reset-rtd1625-crt.c
@@ -0,0 +1,187 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2026 Realtek Semiconductor Corporation
+ */
+
+#include <dt-bindings/reset/realtek,rtd1625.h>
+#include <linux/auxiliary_bus.h>
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <linux/slab.h>
+#include "common.h"
+
+#define RTD1625_CRT_RSTN_MAX 123
+
+static const struct rtk_reset_desc rtd1625_crt_reset_descs[] = {
+ /* Bank 0: offset 0x0 */
+ [RTD1625_CRT_RSTN_MISC] = { .ofs = 0x0, .bit = 0, .write_en = 1 },
+ [RTD1625_CRT_RSTN_DIP] = { .ofs = 0x0, .bit = 2, .write_en = 1 },
+ [RTD1625_CRT_RSTN_GSPI] = { .ofs = 0x0, .bit = 4, .write_en = 1 },
+ [RTD1625_CRT_RSTN_SDS] = { .ofs = 0x0, .bit = 6, .write_en = 1 },
+ [RTD1625_CRT_RSTN_SDS_REG] = { .ofs = 0x0, .bit = 8, .write_en = 1 },
+ [RTD1625_CRT_RSTN_SDS_PHY] = { .ofs = 0x0, .bit = 10, .write_en = 1 },
+ [RTD1625_CRT_RSTN_GPU2D] = { .ofs = 0x0, .bit = 12, .write_en = 1 },
+ [RTD1625_CRT_RSTN_DC_PHY] = { .ofs = 0x0, .bit = 22, .write_en = 1 },
+ [RTD1625_CRT_RSTN_DCPHY_CRT] = { .ofs = 0x0, .bit = 24, .write_en = 1 },
+ [RTD1625_CRT_RSTN_LSADC] = { .ofs = 0x0, .bit = 26, .write_en = 1 },
+ [RTD1625_CRT_RSTN_SE] = { .ofs = 0x0, .bit = 28, .write_en = 1 },
+ [RTD1625_CRT_RSTN_DLA] = { .ofs = 0x0, .bit = 30, .write_en = 1 },
+ /* Bank 1: offset 0x4 */
+ [RTD1625_CRT_RSTN_JPEG] = { .ofs = 0x4, .bit = 0, .write_en = 1 },
+ [RTD1625_CRT_RSTN_SD] = { .ofs = 0x4, .bit = 2, .write_en = 1 },
+ [RTD1625_CRT_RSTN_SDIO] = { .ofs = 0x4, .bit = 6, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCR_CNT] = { .ofs = 0x4, .bit = 8, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE0_STITCH] = { .ofs = 0x4, .bit = 10, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE0_PHY] = { .ofs = 0x4, .bit = 12, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE0] = { .ofs = 0x4, .bit = 14, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE0_CORE] = { .ofs = 0x4, .bit = 16, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE0_POWER] = { .ofs = 0x4, .bit = 18, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE0_NONSTICH] = { .ofs = 0x4, .bit = 20, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE0_PHY_MDIO] = { .ofs = 0x4, .bit = 22, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE0_SGMII_MDIO] = { .ofs = 0x4, .bit = 24, .write_en = 1 },
+ [RTD1625_CRT_RSTN_VO2] = { .ofs = 0x4, .bit = 28, .write_en = 1 },
+ [RTD1625_CRT_RSTN_MISC_SC0] = { .ofs = 0x4, .bit = 30, .write_en = 1 },
+ /* Bank 2: offset 0x8 */
+ [RTD1625_CRT_RSTN_MD] = { .ofs = 0x8, .bit = 4, .write_en = 1 },
+ [RTD1625_CRT_RSTN_LVDS1] = { .ofs = 0x8, .bit = 6, .write_en = 1 },
+ [RTD1625_CRT_RSTN_LVDS2] = { .ofs = 0x8, .bit = 8, .write_en = 1 },
+ [RTD1625_CRT_RSTN_MISC_SC1] = { .ofs = 0x8, .bit = 10, .write_en = 1 },
+ [RTD1625_CRT_RSTN_I2C_3] = { .ofs = 0x8, .bit = 12, .write_en = 1 },
+ [RTD1625_CRT_RSTN_FAN] = { .ofs = 0x8, .bit = 14, .write_en = 1 },
+ [RTD1625_CRT_RSTN_TVE] = { .ofs = 0x8, .bit = 16, .write_en = 1 },
+ [RTD1625_CRT_RSTN_AIO] = { .ofs = 0x8, .bit = 18, .write_en = 1 },
+ [RTD1625_CRT_RSTN_VO] = { .ofs = 0x8, .bit = 20, .write_en = 1 },
+ [RTD1625_CRT_RSTN_MIPI_CSI] = { .ofs = 0x8, .bit = 22, .write_en = 1 },
+ [RTD1625_CRT_RSTN_HDMIRX] = { .ofs = 0x8, .bit = 24, .write_en = 1 },
+ [RTD1625_CRT_RSTN_HDMIRX_WRAP] = { .ofs = 0x8, .bit = 26, .write_en = 1 },
+ [RTD1625_CRT_RSTN_HDMI] = { .ofs = 0x8, .bit = 28, .write_en = 1 },
+ [RTD1625_CRT_RSTN_DISP] = { .ofs = 0x8, .bit = 30, .write_en = 1 },
+ /* Bank 3: offset 0xc */
+ [RTD1625_CRT_RSTN_SATA_PHY_POW1] = { .ofs = 0xc, .bit = 0, .write_en = 1 },
+ [RTD1625_CRT_RSTN_SATA_PHY_POW0] = { .ofs = 0xc, .bit = 2, .write_en = 1 },
+ [RTD1625_CRT_RSTN_SATA_MDIO1] = { .ofs = 0xc, .bit = 4, .write_en = 1 },
+ [RTD1625_CRT_RSTN_SATA_MDIO0] = { .ofs = 0xc, .bit = 6, .write_en = 1 },
+ [RTD1625_CRT_RSTN_SATA_WRAP] = { .ofs = 0xc, .bit = 8, .write_en = 1 },
+ [RTD1625_CRT_RSTN_SATA_MAC_P1] = { .ofs = 0xc, .bit = 10, .write_en = 1 },
+ [RTD1625_CRT_RSTN_SATA_MAC_P0] = { .ofs = 0xc, .bit = 12, .write_en = 1 },
+ [RTD1625_CRT_RSTN_SATA_MAC_COM] = { .ofs = 0xc, .bit = 14, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE1_STITCH] = { .ofs = 0xc, .bit = 16, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE1_PHY] = { .ofs = 0xc, .bit = 18, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE1] = { .ofs = 0xc, .bit = 20, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE1_CORE] = { .ofs = 0xc, .bit = 22, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE1_POWER] = { .ofs = 0xc, .bit = 24, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE1_NONSTICH] = { .ofs = 0xc, .bit = 26, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE1_PHY_MDIO] = { .ofs = 0xc, .bit = 28, .write_en = 1 },
+ [RTD1625_CRT_RSTN_HDMITOP] = { .ofs = 0xc, .bit = 30, .write_en = 1 },
+ /* Bank 4: offset 0x68 */
+ [RTD1625_CRT_RSTN_I2C_4] = { .ofs = 0x68, .bit = 2, .write_en = 1 },
+ [RTD1625_CRT_RSTN_I2C_5] = { .ofs = 0x68, .bit = 4, .write_en = 1 },
+ [RTD1625_CRT_RSTN_TSIO] = { .ofs = 0x68, .bit = 6, .write_en = 1 },
+ [RTD1625_CRT_RSTN_VI] = { .ofs = 0x68, .bit = 8, .write_en = 1 },
+ [RTD1625_CRT_RSTN_EDP] = { .ofs = 0x68, .bit = 10, .write_en = 1 },
+ [RTD1625_CRT_RSTN_VE1_MMU] = { .ofs = 0x68, .bit = 12, .write_en = 1 },
+ [RTD1625_CRT_RSTN_VE1_MMU_FUNC] = { .ofs = 0x68, .bit = 14, .write_en = 1 },
+ [RTD1625_CRT_RSTN_HSE_MMU] = { .ofs = 0x68, .bit = 16, .write_en = 1 },
+ [RTD1625_CRT_RSTN_HSE_MMU_FUNC] = { .ofs = 0x68, .bit = 18, .write_en = 1 },
+ [RTD1625_CRT_RSTN_MDLM2M] = { .ofs = 0x68, .bit = 20, .write_en = 1 },
+ [RTD1625_CRT_RSTN_ISO_GSPI] = { .ofs = 0x68, .bit = 22, .write_en = 1 },
+ [RTD1625_CRT_RSTN_SOFT_NPU] = { .ofs = 0x68, .bit = 24, .write_en = 1 },
+ [RTD1625_CRT_RSTN_SPI2EMMC] = { .ofs = 0x68, .bit = 26, .write_en = 1 },
+ [RTD1625_CRT_RSTN_EARC] = { .ofs = 0x68, .bit = 28, .write_en = 1 },
+ [RTD1625_CRT_RSTN_VE1] = { .ofs = 0x68, .bit = 30, .write_en = 1 },
+ /* Bank 5: offset 0x90 */
+ [RTD1625_CRT_RSTN_PCIE2_STITCH] = { .ofs = 0x90, .bit = 0, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE2_PHY] = { .ofs = 0x90, .bit = 2, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE2] = { .ofs = 0x90, .bit = 4, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE2_CORE] = { .ofs = 0x90, .bit = 6, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE2_POWER] = { .ofs = 0x90, .bit = 8, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE2_NONSTICH] = { .ofs = 0x90, .bit = 10, .write_en = 1 },
+ [RTD1625_CRT_RSTN_PCIE2_PHY_MDIO] = { .ofs = 0x90, .bit = 12, .write_en = 1 },
+ [RTD1625_CRT_RSTN_DCPHY_UMCTL2] = { .ofs = 0x90, .bit = 14, .write_en = 1 },
+ [RTD1625_CRT_RSTN_MIPI_DSI] = { .ofs = 0x90, .bit = 16, .write_en = 1 },
+ [RTD1625_CRT_RSTN_HIFM] = { .ofs = 0x90, .bit = 18, .write_en = 1 },
+ [RTD1625_CRT_RSTN_NSRAM] = { .ofs = 0x90, .bit = 20, .write_en = 1 },
+ [RTD1625_CRT_RSTN_AUCPU0_REG] = { .ofs = 0x90, .bit = 22, .write_en = 1 },
+ [RTD1625_CRT_RSTN_MDL_GENPW] = { .ofs = 0x90, .bit = 24, .write_en = 1 },
+ [RTD1625_CRT_RSTN_MDL_CHIP] = { .ofs = 0x90, .bit = 26, .write_en = 1 },
+ [RTD1625_CRT_RSTN_MDL_IP] = { .ofs = 0x90, .bit = 28, .write_en = 1 },
+ [RTD1625_CRT_RSTN_TEST_MUX] = { .ofs = 0x90, .bit = 30, .write_en = 1 },
+ /* Bank 6: offset 0xb8 */
+ [RTD1625_CRT_RSTN_ISO_BIST] = { .ofs = 0xb8, .bit = 0, .write_en = 1 },
+ [RTD1625_CRT_RSTN_MAIN_BIST] = { .ofs = 0xb8, .bit = 2, .write_en = 1 },
+ [RTD1625_CRT_RSTN_MAIN2_BIST] = { .ofs = 0xb8, .bit = 4, .write_en = 1 },
+ [RTD1625_CRT_RSTN_VE1_BIST] = { .ofs = 0xb8, .bit = 6, .write_en = 1 },
+ [RTD1625_CRT_RSTN_VE2_BIST] = { .ofs = 0xb8, .bit = 8, .write_en = 1 },
+ [RTD1625_CRT_RSTN_DCPHY_BIST] = { .ofs = 0xb8, .bit = 10, .write_en = 1 },
+ [RTD1625_CRT_RSTN_GPU_BIST] = { .ofs = 0xb8, .bit = 12, .write_en = 1 },
+ [RTD1625_CRT_RSTN_DISP_BIST] = { .ofs = 0xb8, .bit = 14, .write_en = 1 },
+ [RTD1625_CRT_RSTN_NPU_BIST] = { .ofs = 0xb8, .bit = 16, .write_en = 1 },
+ [RTD1625_CRT_RSTN_CAS_BIST] = { .ofs = 0xb8, .bit = 18, .write_en = 1 },
+ [RTD1625_CRT_RSTN_VE4_BIST] = { .ofs = 0xb8, .bit = 20, .write_en = 1 },
+ /* Bank 7: offset 0x454 (DUMMY0, no write_en) */
+ [RTD1625_CRT_RSTN_EMMC] = { .ofs = 0x454, .bit = 0 },
+ /* Bank 8: offset 0x458 (DUMMY1, no write_en) */
+ [RTD1625_CRT_RSTN_GPU] = { .ofs = 0x458, .bit = 0 },
+ /* Bank 9: offset 0x464 (DUMMY4, no write_en) */
+ [RTD1625_CRT_RSTN_VE2] = { .ofs = 0x464, .bit = 0 },
+ /* Bank 10: offset 0x880 */
+ [RTD1625_CRT_RSTN_UR1] = { .ofs = 0x880, .bit = 0, .write_en = 1 },
+ [RTD1625_CRT_RSTN_UR2] = { .ofs = 0x880, .bit = 2, .write_en = 1 },
+ [RTD1625_CRT_RSTN_UR3] = { .ofs = 0x880, .bit = 4, .write_en = 1 },
+ [RTD1625_CRT_RSTN_UR4] = { .ofs = 0x880, .bit = 6, .write_en = 1 },
+ [RTD1625_CRT_RSTN_UR5] = { .ofs = 0x880, .bit = 8, .write_en = 1 },
+ [RTD1625_CRT_RSTN_UR6] = { .ofs = 0x880, .bit = 10, .write_en = 1 },
+ [RTD1625_CRT_RSTN_UR7] = { .ofs = 0x880, .bit = 12, .write_en = 1 },
+ [RTD1625_CRT_RSTN_UR8] = { .ofs = 0x880, .bit = 14, .write_en = 1 },
+ [RTD1625_CRT_RSTN_UR9] = { .ofs = 0x880, .bit = 16, .write_en = 1 },
+ [RTD1625_CRT_RSTN_UR_TOP] = { .ofs = 0x880, .bit = 18, .write_en = 1 },
+ [RTD1625_CRT_RSTN_I2C_7] = { .ofs = 0x880, .bit = 28, .write_en = 1 },
+ [RTD1625_CRT_RSTN_I2C_6] = { .ofs = 0x880, .bit = 30, .write_en = 1 },
+ /* Bank 11: offset 0x890 */
+ [RTD1625_CRT_RSTN_SPI0] = { .ofs = 0x890, .bit = 0, .write_en = 1 },
+ [RTD1625_CRT_RSTN_SPI1] = { .ofs = 0x890, .bit = 2, .write_en = 1 },
+ [RTD1625_CRT_RSTN_SPI2] = { .ofs = 0x890, .bit = 4, .write_en = 1 },
+ [RTD1625_CRT_RSTN_LSADC0] = { .ofs = 0x890, .bit = 16, .write_en = 1 },
+ [RTD1625_CRT_RSTN_LSADC1] = { .ofs = 0x890, .bit = 18, .write_en = 1 },
+ [RTD1625_CRT_RSTN_ISOMIS_DMA] = { .ofs = 0x890, .bit = 20, .write_en = 1 },
+ [RTD1625_CRT_RSTN_AUDIO_ADC] = { .ofs = 0x890, .bit = 22, .write_en = 1 },
+ [RTD1625_CRT_RSTN_DPTX] = { .ofs = 0x890, .bit = 24, .write_en = 1 },
+ [RTD1625_CRT_RSTN_AUCPU1_REG] = { .ofs = 0x890, .bit = 26, .write_en = 1 },
+ [RTD1625_CRT_RSTN_EDPTX] = { .ofs = 0x890, .bit = 28, .write_en = 1 },
+};
+
+static int rtd1625_crt_reset_probe(struct auxiliary_device *adev,
+ const struct auxiliary_device_id *id)
+{
+ struct device *dev = &adev->dev;
+ struct rtk_reset_data *data;
+
+ data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ data->descs = rtd1625_crt_reset_descs;
+ data->rcdev.nr_resets = RTD1625_CRT_RSTN_MAX;
+ data->rcdev.owner = THIS_MODULE;
+
+ return rtk_reset_controller_add(dev, data);
+}
+
+static const struct auxiliary_device_id rtd1625_crt_reset_ids[] = {
+ { .name = "clk_rtk.crt_rst" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(auxiliary, rtd1625_crt_reset_ids);
+
+static struct auxiliary_driver rtd1625_crt_driver = {
+ .probe = rtd1625_crt_reset_probe,
+ .id_table = rtd1625_crt_reset_ids,
+ .driver = {
+ .name = "rtd1625-crt-reset",
+ },
+};
+module_auxiliary_driver(rtd1625_crt_driver);
+
+MODULE_DESCRIPTION("Realtek RTD1625 CRT Reset Controller Driver");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS("REALTEK_RESET");
--
2.43.0
^ permalink raw reply related
* [PATCH v8 02/10] reset: Add Realtek basic reset support
From: Yu-Chun Lin @ 2026-06-10 8:08 UTC (permalink / raw)
To: mturquette, sboyd, robh, krzk+dt, conor+dt, p.zabel, cylee12,
afaerber, jyanchou
Cc: bmasney, devicetree, linux-clk, linux-kernel, linux-arm-kernel,
linux-realtek-soc, james.tai, cy.huang, stanley_chang,
eleanor.lin
In-Reply-To: <20260610080824.255063-1-eleanor.lin@realtek.com>
From: Cheng-Yu Lee <cylee12@realtek.com>
Define the reset operations backed by a regmap-based register interface
and prepare the reset controller to be registered through the reset
framework.
Since the reset controllers on Realtek SoCs often share the same register
space with the clock controllers, this common framework is designed to
extract the regmap and device tree node from the parent device
(e.g., an auxiliary device parent).
Signed-off-by: Cheng-Yu Lee <cylee12@realtek.com>
Co-developed-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com>
---
Changes in v8:
- None
---
MAINTAINERS | 1 +
drivers/reset/Kconfig | 1 +
drivers/reset/Makefile | 1 +
drivers/reset/realtek/Kconfig | 8 +++
drivers/reset/realtek/Makefile | 2 +
drivers/reset/realtek/common.c | 90 ++++++++++++++++++++++++++++++++++
drivers/reset/realtek/common.h | 29 +++++++++++
7 files changed, 132 insertions(+)
create mode 100644 drivers/reset/realtek/Kconfig
create mode 100644 drivers/reset/realtek/Makefile
create mode 100644 drivers/reset/realtek/common.c
create mode 100644 drivers/reset/realtek/common.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 613ca7e95e47..80e840a6691d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -22484,6 +22484,7 @@ L: devicetree@vger.kernel.org
L: linux-clk@vger.kernel.org
S: Supported
F: Documentation/devicetree/bindings/clock/realtek*
+F: drivers/reset/realtek/*
F: include/dt-bindings/clock/realtek*
F: include/dt-bindings/reset/realtek*
diff --git a/drivers/reset/Kconfig b/drivers/reset/Kconfig
index d009eb0849a3..45a4227b5f44 100644
--- a/drivers/reset/Kconfig
+++ b/drivers/reset/Kconfig
@@ -418,6 +418,7 @@ config RESET_ZYNQMP
source "drivers/reset/amlogic/Kconfig"
source "drivers/reset/hisilicon/Kconfig"
+source "drivers/reset/realtek/Kconfig"
source "drivers/reset/spacemit/Kconfig"
source "drivers/reset/starfive/Kconfig"
source "drivers/reset/sti/Kconfig"
diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile
index 3e52569bd276..7330fee91365 100644
--- a/drivers/reset/Makefile
+++ b/drivers/reset/Makefile
@@ -2,6 +2,7 @@
obj-y += core.o
obj-y += amlogic/
obj-y += hisilicon/
+obj-y += realtek/
obj-y += spacemit/
obj-y += starfive/
obj-y += sti/
diff --git a/drivers/reset/realtek/Kconfig b/drivers/reset/realtek/Kconfig
new file mode 100644
index 000000000000..bb6dd856a64a
--- /dev/null
+++ b/drivers/reset/realtek/Kconfig
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config RESET_RTK_COMMON
+ tristate "Realtek common reset driver" if COMPILE_TEST
+ help
+ This option enables the common reset controller library for
+ Realtek SoCs. It provides shared reset control operations
+ (assert, deassert, status) and a registration helper function
+ that other Realtek-specific reset drivers can use.
diff --git a/drivers/reset/realtek/Makefile b/drivers/reset/realtek/Makefile
new file mode 100644
index 000000000000..b59a3f7f2453
--- /dev/null
+++ b/drivers/reset/realtek/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_RESET_RTK_COMMON) += common.o
diff --git a/drivers/reset/realtek/common.c b/drivers/reset/realtek/common.c
new file mode 100644
index 000000000000..2ce20c25377b
--- /dev/null
+++ b/drivers/reset/realtek/common.c
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2019-2026 Realtek Semiconductor Corporation
+ */
+
+#include <linux/device.h>
+#include <linux/export.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+#include "common.h"
+
+static inline struct rtk_reset_data *to_rtk_reset_controller(struct reset_controller_dev *r)
+{
+ return container_of(r, struct rtk_reset_data, rcdev);
+}
+
+static inline const struct rtk_reset_desc *rtk_reset_get_desc(struct rtk_reset_data *data,
+ unsigned long idx)
+{
+ return &data->descs[idx];
+}
+
+static int rtk_reset_assert(struct reset_controller_dev *rcdev,
+ unsigned long idx)
+{
+ struct rtk_reset_data *data = to_rtk_reset_controller(rcdev);
+ const struct rtk_reset_desc *desc;
+ u32 mask, val;
+
+ desc = rtk_reset_get_desc(data, idx);
+ mask = desc->write_en ? (0x3U << desc->bit) : BIT(desc->bit);
+ val = desc->write_en ? (0x2U << desc->bit) : 0;
+
+ return regmap_update_bits(data->regmap, desc->ofs, mask, val);
+}
+
+static int rtk_reset_deassert(struct reset_controller_dev *rcdev,
+ unsigned long idx)
+{
+ struct rtk_reset_data *data = to_rtk_reset_controller(rcdev);
+ const struct rtk_reset_desc *desc;
+ u32 mask, val;
+
+ desc = rtk_reset_get_desc(data, idx);
+ mask = desc->write_en ? (0x3U << desc->bit) : BIT(desc->bit);
+ val = mask;
+
+ return regmap_update_bits(data->regmap, desc->ofs, mask, val);
+}
+
+static int rtk_reset_status(struct reset_controller_dev *rcdev,
+ unsigned long idx)
+{
+ struct rtk_reset_data *data = to_rtk_reset_controller(rcdev);
+ const struct rtk_reset_desc *desc;
+ u32 val;
+ int ret;
+
+ desc = rtk_reset_get_desc(data, idx);
+ ret = regmap_read(data->regmap, desc->ofs, &val);
+ if (ret)
+ return ret;
+
+ return !((val >> desc->bit) & 1);
+}
+
+static const struct reset_control_ops rtk_reset_ops = {
+ .assert = rtk_reset_assert,
+ .deassert = rtk_reset_deassert,
+ .status = rtk_reset_status,
+};
+
+/* The caller must initialize data->descs, data->rcdev.nr_resets and
+ * data->rcdev.owner before calling rtk_reset_controller_add().
+ */
+int rtk_reset_controller_add(struct device *dev,
+ struct rtk_reset_data *data)
+{
+ data->regmap = dev_get_platdata(dev);
+ data->rcdev.ops = &rtk_reset_ops;
+ data->rcdev.dev = dev;
+ data->rcdev.of_node = dev->parent->of_node;
+
+ return devm_reset_controller_register(dev, &data->rcdev);
+}
+EXPORT_SYMBOL_NS_GPL(rtk_reset_controller_add, "REALTEK_RESET");
+
+MODULE_DESCRIPTION("realtek reset infrastructure");
+MODULE_LICENSE("GPL");
diff --git a/drivers/reset/realtek/common.h b/drivers/reset/realtek/common.h
new file mode 100644
index 000000000000..42eb41eae2ec
--- /dev/null
+++ b/drivers/reset/realtek/common.h
@@ -0,0 +1,29 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2026 Realtek Semiconductor Corporation
+ * Author: Yu-Chun Lin <eleanor.lin@realtek.com>
+ */
+
+#ifndef __RESET_REALTEK_COMMON_H
+#define __RESET_REALTEK_COMMON_H
+
+#include <linux/reset-controller.h>
+
+struct regmap;
+
+struct rtk_reset_desc {
+ u32 ofs;
+ u32 bit;
+ bool write_en;
+};
+
+struct rtk_reset_data {
+ struct reset_controller_dev rcdev;
+ const struct rtk_reset_desc *descs;
+ struct regmap *regmap;
+};
+
+int rtk_reset_controller_add(struct device *dev,
+ struct rtk_reset_data *initdata);
+
+#endif /* __RESET_REALTEK_COMMON_H */
--
2.43.0
^ permalink raw reply related
* [PATCH v8 06/10] clk: realtek: Add support for mux clock
From: Yu-Chun Lin @ 2026-06-10 8:08 UTC (permalink / raw)
To: mturquette, sboyd, robh, krzk+dt, conor+dt, p.zabel, cylee12,
afaerber, jyanchou
Cc: bmasney, devicetree, linux-clk, linux-kernel, linux-arm-kernel,
linux-realtek-soc, james.tai, cy.huang, stanley_chang,
eleanor.lin
In-Reply-To: <20260610080824.255063-1-eleanor.lin@realtek.com>
From: Cheng-Yu Lee <cylee12@realtek.com>
Add a simple regmap-based clk_ops implementation for Realtek mux clocks.
The implementation supports parent selection and rate determination through
regmap-backed register access.
Signed-off-by: Cheng-Yu Lee <cylee12@realtek.com>
Co-developed-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com>
---
Changes in v8:
- In clk_regmap_mux_get_parent(), return 0xff instead of 0 to properly indicate
an error.
- In clk_regmap_mux_set_parent(), cast index to u32 to avoid signed integer
- overflow.
---
drivers/clk/realtek/Makefile | 1 +
drivers/clk/realtek/clk-regmap-mux.c | 41 ++++++++++++++++++++++++++
drivers/clk/realtek/clk-regmap-mux.h | 43 ++++++++++++++++++++++++++++
3 files changed, 85 insertions(+)
create mode 100644 drivers/clk/realtek/clk-regmap-mux.c
create mode 100644 drivers/clk/realtek/clk-regmap-mux.h
diff --git a/drivers/clk/realtek/Makefile b/drivers/clk/realtek/Makefile
index 74375f8127ac..f90dc57fcfdb 100644
--- a/drivers/clk/realtek/Makefile
+++ b/drivers/clk/realtek/Makefile
@@ -5,4 +5,5 @@ clk-rtk-y += common.o
clk-rtk-y += clk-pll.o
clk-rtk-y += clk-regmap-gate.o
+clk-rtk-y += clk-regmap-mux.o
clk-rtk-y += freq_table.o
diff --git a/drivers/clk/realtek/clk-regmap-mux.c b/drivers/clk/realtek/clk-regmap-mux.c
new file mode 100644
index 000000000000..8bb66a9e244a
--- /dev/null
+++ b/drivers/clk/realtek/clk-regmap-mux.c
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2017-2026 Realtek Semiconductor Corporation
+ * Author: Cheng-Yu Lee <cylee12@realtek.com>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/export.h>
+#include <linux/regmap.h>
+#include "clk-regmap-mux.h"
+
+static u8 clk_regmap_mux_get_parent(struct clk_hw *hw)
+{
+ struct clk_regmap_mux *clkm = to_clk_regmap_mux(hw);
+ int num_parents = clk_hw_get_num_parents(hw);
+ u32 val;
+ int ret;
+
+ ret = regmap_read(clkm->clkr.regmap, clkm->mux_ofs, &val);
+ if (ret)
+ return 0;
+
+ val = (val >> clkm->shift) & clkm->mask;
+
+ return val >= num_parents ? 0xff : val;
+}
+
+static int clk_regmap_mux_set_parent(struct clk_hw *hw, u8 index)
+{
+ struct clk_regmap_mux *clkm = to_clk_regmap_mux(hw);
+
+ return regmap_update_bits(clkm->clkr.regmap, clkm->mux_ofs,
+ clkm->mask << clkm->shift, (u32)index << clkm->shift);
+}
+
+const struct clk_ops rtk_clk_regmap_mux_ops = {
+ .set_parent = clk_regmap_mux_set_parent,
+ .get_parent = clk_regmap_mux_get_parent,
+ .determine_rate = __clk_mux_determine_rate,
+};
+EXPORT_SYMBOL_NS_GPL(rtk_clk_regmap_mux_ops, "REALTEK_CLK");
diff --git a/drivers/clk/realtek/clk-regmap-mux.h b/drivers/clk/realtek/clk-regmap-mux.h
new file mode 100644
index 000000000000..fff413222d19
--- /dev/null
+++ b/drivers/clk/realtek/clk-regmap-mux.h
@@ -0,0 +1,43 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2017-2026 Realtek Semiconductor Corporation
+ * Author: Cheng-Yu Lee <cylee12@realtek.com>
+ */
+
+#ifndef __CLK_REALTEK_CLK_REGMAP_MUX_H
+#define __CLK_REALTEK_CLK_REGMAP_MUX_H
+
+#include "common.h"
+
+struct clk_regmap_mux {
+ struct clk_regmap clkr;
+ int mux_ofs;
+ unsigned int mask;
+ unsigned int shift;
+};
+
+#define __clk_regmap_mux_hw(_p) __clk_regmap_hw(&(_p)->clkr)
+
+#define __CLK_REGMAP_MUX(_name, _parents, _ops, _flags, _ofs, _sft, _mask) \
+ struct clk_regmap_mux _name = { \
+ .clkr.hw.init = \
+ CLK_HW_INIT_PARENTS(#_name, _parents, _ops, _flags), \
+ .mux_ofs = _ofs, \
+ .shift = _sft, \
+ .mask = _mask, \
+ }
+
+#define CLK_REGMAP_MUX(_name, _parents, _flags, _ofs, _sft, _mask) \
+ __CLK_REGMAP_MUX(_name, _parents, &rtk_clk_regmap_mux_ops, _flags, _ofs, \
+ _sft, _mask)
+
+static inline struct clk_regmap_mux *to_clk_regmap_mux(struct clk_hw *hw)
+{
+ struct clk_regmap *clkr = to_clk_regmap(hw);
+
+ return container_of(clkr, struct clk_regmap_mux, clkr);
+}
+
+extern const struct clk_ops rtk_clk_regmap_mux_ops;
+
+#endif /* __CLK_REALTEK_CLK_REGMAP_MUX_H */
--
2.43.0
^ permalink raw reply related
* [PATCH v8 03/10] clk: realtek: Introduce a common probe()
From: Yu-Chun Lin @ 2026-06-10 8:08 UTC (permalink / raw)
To: mturquette, sboyd, robh, krzk+dt, conor+dt, p.zabel, cylee12,
afaerber, jyanchou
Cc: bmasney, devicetree, linux-clk, linux-kernel, linux-arm-kernel,
linux-realtek-soc, james.tai, cy.huang, stanley_chang,
eleanor.lin
In-Reply-To: <20260610080824.255063-1-eleanor.lin@realtek.com>
From: Cheng-Yu Lee <cylee12@realtek.com>
Add rtk_clk_probe() to set up the shared regmap, register clock hardware,
and add the clock provider.
Additionally, if the "#reset-cells" property is present in the device tree,
it creates and registers an auxiliary device using the provided aux_name.
This allows the dedicated reset driver to bind to this device, enabling
both clock and reset drivers to share the same regmap.
Signed-off-by: Cheng-Yu Lee <cylee12@realtek.com>
Co-developed-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com>
---
Changes in v8:
- Add depends on RESET_CONTROLLER and select MFD_SYSCON for config
RTK_CLK_COMMON.
- Fix error handling for devm_auxiliary_device_create().
---
MAINTAINERS | 1 +
drivers/clk/Kconfig | 1 +
drivers/clk/Makefile | 1 +
drivers/clk/realtek/Kconfig | 30 ++++++++++++++++
drivers/clk/realtek/Makefile | 4 +++
drivers/clk/realtek/common.c | 66 ++++++++++++++++++++++++++++++++++++
drivers/clk/realtek/common.h | 37 ++++++++++++++++++++
7 files changed, 140 insertions(+)
create mode 100644 drivers/clk/realtek/Kconfig
create mode 100644 drivers/clk/realtek/Makefile
create mode 100644 drivers/clk/realtek/common.c
create mode 100644 drivers/clk/realtek/common.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 80e840a6691d..aec1ea6d35d6 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -22484,6 +22484,7 @@ L: devicetree@vger.kernel.org
L: linux-clk@vger.kernel.org
S: Supported
F: Documentation/devicetree/bindings/clock/realtek*
+F: drivers/clk/realtek/*
F: drivers/reset/realtek/*
F: include/dt-bindings/clock/realtek*
F: include/dt-bindings/reset/realtek*
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index b2efbe9f6acb..8bf262dd23a9 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -519,6 +519,7 @@ source "drivers/clk/nuvoton/Kconfig"
source "drivers/clk/pistachio/Kconfig"
source "drivers/clk/qcom/Kconfig"
source "drivers/clk/ralink/Kconfig"
+source "drivers/clk/realtek/Kconfig"
source "drivers/clk/renesas/Kconfig"
source "drivers/clk/rockchip/Kconfig"
source "drivers/clk/samsung/Kconfig"
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index a3e2862ebd7e..e226bee2d039 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -140,6 +140,7 @@ obj-$(CONFIG_COMMON_CLK_PISTACHIO) += pistachio/
obj-$(CONFIG_COMMON_CLK_PXA) += pxa/
obj-$(CONFIG_COMMON_CLK_QCOM) += qcom/
obj-y += ralink/
+obj-$(CONFIG_COMMON_CLK_REALTEK) += realtek/
obj-y += renesas/
obj-$(CONFIG_ARCH_ROCKCHIP) += rockchip/
obj-$(CONFIG_COMMON_CLK_SAMSUNG) += samsung/
diff --git a/drivers/clk/realtek/Kconfig b/drivers/clk/realtek/Kconfig
new file mode 100644
index 000000000000..ed97531e321d
--- /dev/null
+++ b/drivers/clk/realtek/Kconfig
@@ -0,0 +1,30 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config COMMON_CLK_REALTEK
+ tristate "Clock driver for Realtek SoCs"
+ depends on ARCH_REALTEK || COMPILE_TEST
+ default ARCH_REALTEK
+ help
+ Enable the common clock framework infrastructure for Realtek
+ system-on-chip platforms.
+
+ This provides the base support required by individual Realtek
+ clock controller drivers to expose clocks to peripheral devices.
+
+ If you have a Realtek-based platform, say Y.
+
+if COMMON_CLK_REALTEK
+
+config RTK_CLK_COMMON
+ tristate "Realtek Clock Common"
+ depends on RESET_CONTROLLER
+ select AUXILIARY_BUS
+ select MFD_SYSCON
+ select RESET_RTK_COMMON
+ help
+ Common helper code shared by Realtek clock controller drivers.
+
+ This provides utility functions and data structures used by
+ multiple Realtek clock implementations, and include integration
+ with reset controllers where required.
+
+endif
diff --git a/drivers/clk/realtek/Makefile b/drivers/clk/realtek/Makefile
new file mode 100644
index 000000000000..377ec776ee47
--- /dev/null
+++ b/drivers/clk/realtek/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_RTK_CLK_COMMON) += clk-rtk.o
+
+clk-rtk-y += common.o
diff --git a/drivers/clk/realtek/common.c b/drivers/clk/realtek/common.c
new file mode 100644
index 000000000000..1b40fcc59a76
--- /dev/null
+++ b/drivers/clk/realtek/common.c
@@ -0,0 +1,66 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2019-2026 Realtek Semiconductor Corporation
+ * Author: Cheng-Yu Lee <cylee12@realtek.com>
+ */
+
+#include <linux/auxiliary_bus.h>
+#include <linux/device.h>
+#include <linux/export.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include "common.h"
+
+static int rtk_reset_controller_register(struct device *dev, const char *aux_name,
+ struct regmap *map)
+{
+ struct auxiliary_device *adev;
+
+ if (!of_property_present(dev->of_node, "#reset-cells"))
+ return 0;
+
+ adev = devm_auxiliary_device_create(dev, aux_name, (void *)map);
+
+ if (!adev)
+ return -ENOMEM;
+
+ return 0;
+}
+
+int rtk_clk_probe(struct platform_device *pdev, const struct rtk_clk_desc *desc,
+ const char *aux_name)
+{
+ struct device *dev = &pdev->dev;
+ struct regmap *regmap;
+ int i, ret;
+
+ regmap = device_node_to_regmap(dev->of_node);
+ if (IS_ERR(regmap))
+ return dev_err_probe(dev, PTR_ERR(regmap), "failed to get regmap\n");
+
+ for (i = 0; i < desc->num_clks; i++)
+ desc->clks[i]->regmap = regmap;
+
+ for (i = 0; i < desc->clk_data->num; i++) {
+ struct clk_hw *hw = desc->clk_data->hws[i];
+
+ if (!hw)
+ continue;
+
+ ret = devm_clk_hw_register(dev, hw);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to register hw of clk%d\n", i);
+ }
+
+ ret = devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get,
+ desc->clk_data);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to add clock provider\n");
+
+ return rtk_reset_controller_register(dev, aux_name, regmap);
+}
+EXPORT_SYMBOL_NS_GPL(rtk_clk_probe, "REALTEK_CLK");
+
+MODULE_DESCRIPTION("Realtek clock infrastructure");
+MODULE_LICENSE("GPL");
diff --git a/drivers/clk/realtek/common.h b/drivers/clk/realtek/common.h
new file mode 100644
index 000000000000..c52fcdbff5ee
--- /dev/null
+++ b/drivers/clk/realtek/common.h
@@ -0,0 +1,37 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2016-2026 Realtek Semiconductor Corporation
+ * Author: Cheng-Yu Lee <cylee12@realtek.com>
+ */
+
+#ifndef __CLK_REALTEK_COMMON_H
+#define __CLK_REALTEK_COMMON_H
+
+#include <linux/clk-provider.h>
+
+#define __clk_regmap_hw(_p) ((_p)->hw)
+
+struct device;
+struct platform_device;
+struct regmap;
+
+struct clk_regmap {
+ struct clk_hw hw;
+ struct regmap *regmap;
+};
+
+struct rtk_clk_desc {
+ struct clk_hw_onecell_data *clk_data;
+ struct clk_regmap * const *clks;
+ size_t num_clks;
+};
+
+static inline struct clk_regmap *to_clk_regmap(struct clk_hw *hw)
+{
+ return container_of(hw, struct clk_regmap, hw);
+}
+
+int rtk_clk_probe(struct platform_device *pdev, const struct rtk_clk_desc *desc,
+ const char *aux_name);
+
+#endif /* __CLK_REALTEK_COMMON_H */
--
2.43.0
^ permalink raw reply related
* [PATCH v8 04/10] clk: realtek: Add support for phase locked loops (PLLs)
From: Yu-Chun Lin @ 2026-06-10 8:08 UTC (permalink / raw)
To: mturquette, sboyd, robh, krzk+dt, conor+dt, p.zabel, cylee12,
afaerber, jyanchou
Cc: bmasney, devicetree, linux-clk, linux-kernel, linux-arm-kernel,
linux-realtek-soc, james.tai, cy.huang, stanley_chang,
eleanor.lin
In-Reply-To: <20260610080824.255063-1-eleanor.lin@realtek.com>
From: Cheng-Yu Lee <cylee12@realtek.com>
Provide a full set of PLL operations for programmable PLLs and a read-only
variant for fixed or hardware-managed PLLs.
Signed-off-by: Cheng-Yu Lee <cylee12@realtek.com>
Co-developed-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com>
---
Changes in v8:
- Reduce the timeout value in regmap_read_poll_timeout_atomic() from 2000ms to
500ms to avoid prolonged busy-waiting and prevent triggering the NMI Watchdog.
- Remove 'freq_ready_valid' and add comments to clarify that register offset 0
is never a valid address on Realtek SoCs, meaning it is not configured.
- Add the missing spin_unlock_irqrestore() when regmap_read() fails.
---
drivers/clk/realtek/Makefile | 2 +
drivers/clk/realtek/clk-pll.c | 209 +++++++++++++++++++++++++++++++
drivers/clk/realtek/clk-pll.h | 47 +++++++
drivers/clk/realtek/freq_table.c | 38 ++++++
drivers/clk/realtek/freq_table.h | 16 +++
5 files changed, 312 insertions(+)
create mode 100644 drivers/clk/realtek/clk-pll.c
create mode 100644 drivers/clk/realtek/clk-pll.h
create mode 100644 drivers/clk/realtek/freq_table.c
create mode 100644 drivers/clk/realtek/freq_table.h
diff --git a/drivers/clk/realtek/Makefile b/drivers/clk/realtek/Makefile
index 377ec776ee47..a89ad77993e9 100644
--- a/drivers/clk/realtek/Makefile
+++ b/drivers/clk/realtek/Makefile
@@ -2,3 +2,5 @@
obj-$(CONFIG_RTK_CLK_COMMON) += clk-rtk.o
clk-rtk-y += common.o
+clk-rtk-y += clk-pll.o
+clk-rtk-y += freq_table.o
diff --git a/drivers/clk/realtek/clk-pll.c b/drivers/clk/realtek/clk-pll.c
new file mode 100644
index 000000000000..6c4343d71dbe
--- /dev/null
+++ b/drivers/clk/realtek/clk-pll.c
@@ -0,0 +1,209 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2024-2026 Realtek Semiconductor Corporation
+ * Author: Cheng-Yu Lee <cylee12@realtek.com>
+ */
+
+#include <linux/export.h>
+#include <linux/regmap.h>
+#include <linux/spinlock.h>
+#include "clk-pll.h"
+
+#define TIMEOUT 500
+
+static inline struct clk_pll *to_clk_pll(struct clk_hw *hw)
+{
+ struct clk_regmap *clkr = to_clk_regmap(hw);
+
+ return container_of(clkr, struct clk_pll, clkr);
+}
+
+static int wait_freq_ready(struct clk_pll *clkp)
+{
+ u32 pollval;
+
+ /* reg == 0 means not configured.
+ * Register offset 0 is never a valid address on Realtek SoCs.
+ */
+ if (!clkp->freq_ready_reg)
+ return 0;
+
+ return regmap_read_poll_timeout_atomic(clkp->clkr.regmap, clkp->freq_ready_reg, pollval,
+ (pollval & clkp->freq_ready_mask) == clkp->freq_ready_val, 1, TIMEOUT);
+}
+
+static bool is_power_on(struct clk_pll *clkp)
+{
+ u32 val;
+
+ /* reg == 0 means not configured (assume always on).
+ * Register offset 0 is never a valid address on Realtek SoCs.
+ */
+ if (!clkp->power_reg)
+ return true;
+
+ if (regmap_read(clkp->clkr.regmap, clkp->power_reg, &val))
+ return true;
+
+ return (val & clkp->power_mask) == clkp->power_val_on;
+}
+
+static void clk_pll_disable(struct clk_hw *hw)
+{
+ struct clk_pll *clkp = to_clk_pll(hw);
+ unsigned long flags;
+
+ if (!clkp->seq_power_off)
+ return;
+
+ spin_lock_irqsave(&clkp->lock, flags);
+
+ regmap_multi_reg_write(clkp->clkr.regmap, clkp->seq_power_off,
+ clkp->num_seq_power_off);
+
+ spin_unlock_irqrestore(&clkp->lock, flags);
+}
+
+static int clk_pll_is_enabled(struct clk_hw *hw)
+{
+ struct clk_pll *clkp = to_clk_pll(hw);
+ unsigned long flags;
+ int ret;
+
+ spin_lock_irqsave(&clkp->lock, flags);
+
+ ret = is_power_on(clkp);
+
+ spin_unlock_irqrestore(&clkp->lock, flags);
+
+ return ret;
+}
+
+static int clk_pll_determine_rate(struct clk_hw *hw,
+ struct clk_rate_request *req)
+{
+ struct clk_pll *clkp = to_clk_pll(hw);
+ const struct freq_table *ftblv = NULL;
+
+ ftblv = ftbl_find_by_rate(clkp->freq_tbl, req->rate);
+ if (!ftblv)
+ return -EINVAL;
+
+ req->rate = ftblv->rate;
+
+ return 0;
+}
+
+static unsigned long clk_pll_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct clk_pll *clkp = to_clk_pll(hw);
+ const struct freq_table *fv;
+ unsigned long flags;
+ u32 freq_val;
+
+ spin_lock_irqsave(&clkp->lock, flags);
+
+ if (regmap_read(clkp->clkr.regmap, clkp->freq_reg, &freq_val)) {
+ spin_unlock_irqrestore(&clkp->lock, flags);
+ return 0;
+ }
+
+ freq_val &= clkp->freq_mask;
+
+ fv = ftbl_find_by_val_with_mask(clkp->freq_tbl, clkp->freq_mask,
+ freq_val);
+
+ spin_unlock_irqrestore(&clkp->lock, flags);
+
+ return fv ? fv->rate : 0;
+}
+
+static int clk_pll_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct clk_pll *clkp = to_clk_pll(hw);
+ const struct freq_table *fv;
+ unsigned long flags;
+ int ret;
+
+ fv = ftbl_find_by_rate(clkp->freq_tbl, rate);
+ if (!fv || fv->rate != rate)
+ return -EINVAL;
+
+ spin_lock_irqsave(&clkp->lock, flags);
+
+ if (clkp->seq_pre_set_freq) {
+ ret = regmap_multi_reg_write(clkp->clkr.regmap, clkp->seq_pre_set_freq,
+ clkp->num_seq_pre_set_freq);
+ if (ret)
+ goto unlock;
+ }
+
+ ret = regmap_update_bits(clkp->clkr.regmap, clkp->freq_reg,
+ clkp->freq_mask, fv->val);
+ if (ret)
+ goto unlock;
+
+ if (clkp->seq_post_set_freq) {
+ ret = regmap_multi_reg_write(clkp->clkr.regmap, clkp->seq_post_set_freq,
+ clkp->num_seq_post_set_freq);
+ if (ret)
+ goto unlock;
+ }
+
+ if (is_power_on(clkp)) {
+ ret = wait_freq_ready(clkp);
+ if (ret)
+ goto unlock;
+ }
+
+unlock:
+ spin_unlock_irqrestore(&clkp->lock, flags);
+
+ return ret;
+}
+
+static int clk_pll_enable(struct clk_hw *hw)
+{
+ struct clk_pll *clkp = to_clk_pll(hw);
+ unsigned long flags;
+ int ret = 0;
+
+ if (!clkp->seq_power_on)
+ return ret;
+
+ spin_lock_irqsave(&clkp->lock, flags);
+
+ if (is_power_on(clkp))
+ goto unlock;
+
+ ret = regmap_multi_reg_write(clkp->clkr.regmap, clkp->seq_power_on,
+ clkp->num_seq_power_on);
+ if (ret)
+ goto unlock;
+
+ ret = wait_freq_ready(clkp);
+ if (ret)
+ goto unlock;
+
+unlock:
+ spin_unlock_irqrestore(&clkp->lock, flags);
+
+ return ret;
+}
+
+const struct clk_ops rtk_clk_pll_ops = {
+ .enable = clk_pll_enable,
+ .disable = clk_pll_disable,
+ .is_enabled = clk_pll_is_enabled,
+ .recalc_rate = clk_pll_recalc_rate,
+ .determine_rate = clk_pll_determine_rate,
+ .set_rate = clk_pll_set_rate,
+};
+EXPORT_SYMBOL_NS_GPL(rtk_clk_pll_ops, "REALTEK_CLK");
+
+const struct clk_ops rtk_clk_pll_ro_ops = {
+ .recalc_rate = clk_pll_recalc_rate,
+};
+EXPORT_SYMBOL_NS_GPL(rtk_clk_pll_ro_ops, "REALTEK_CLK");
diff --git a/drivers/clk/realtek/clk-pll.h b/drivers/clk/realtek/clk-pll.h
new file mode 100644
index 000000000000..59abfa9a6122
--- /dev/null
+++ b/drivers/clk/realtek/clk-pll.h
@@ -0,0 +1,47 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2017-2026 Realtek Semiconductor Corporation
+ * Author: Cheng-Yu Lee <cylee12@realtek.com>
+ */
+
+#ifndef __CLK_REALTEK_CLK_PLL_H
+#define __CLK_REALTEK_CLK_PLL_H
+
+#include <linux/spinlock.h>
+#include "common.h"
+#include "freq_table.h"
+
+struct reg_sequence;
+
+struct clk_pll {
+ struct clk_regmap clkr;
+ const struct reg_sequence *seq_power_on;
+ u32 num_seq_power_on;
+ const struct reg_sequence *seq_power_off;
+ u32 num_seq_power_off;
+ const struct reg_sequence *seq_pre_set_freq;
+ u32 num_seq_pre_set_freq;
+ const struct reg_sequence *seq_post_set_freq;
+ u32 num_seq_post_set_freq;
+ const struct freq_table *freq_tbl;
+ u32 freq_reg;
+ u32 freq_mask;
+ u32 freq_ready_mask;
+ u32 freq_ready_reg;
+ u32 freq_ready_val;
+ u32 power_reg;
+ u32 power_mask;
+ u32 power_val_on;
+
+ /* This lock prevents race conditions when multiple CPUs or contexts
+ * simultaneously access this PLL's registers during multi-step operations
+ */
+ spinlock_t lock;
+};
+
+#define __clk_pll_hw(_ptr) __clk_regmap_hw(&(_ptr)->clkr)
+
+extern const struct clk_ops rtk_clk_pll_ops;
+extern const struct clk_ops rtk_clk_pll_ro_ops;
+
+#endif /* __CLK_REALTEK_CLK_PLL_H */
diff --git a/drivers/clk/realtek/freq_table.c b/drivers/clk/realtek/freq_table.c
new file mode 100644
index 000000000000..0ff1e5e79102
--- /dev/null
+++ b/drivers/clk/realtek/freq_table.c
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/bitops.h>
+#include "freq_table.h"
+
+#define IS_FREQ_TABLE_END(_f) ((_f)->rate == 0)
+
+const struct freq_table *ftbl_find_by_rate(const struct freq_table *ftbl,
+ unsigned long rate)
+{
+ const struct freq_table *best = NULL;
+ unsigned long best_rate = 0;
+
+ for (; !IS_FREQ_TABLE_END(ftbl); ftbl++) {
+ if (ftbl->rate == rate)
+ return ftbl;
+
+ if (ftbl->rate > rate)
+ continue;
+
+ if (ftbl->rate > best_rate) {
+ best_rate = ftbl->rate;
+ best = ftbl;
+ }
+ }
+
+ return best;
+}
+
+const struct freq_table *
+ftbl_find_by_val_with_mask(const struct freq_table *ftbl, u32 mask, u32 value)
+{
+ for (; !IS_FREQ_TABLE_END(ftbl); ftbl++) {
+ if ((ftbl->val & mask) == (value & mask))
+ return ftbl;
+ }
+ return NULL;
+};
diff --git a/drivers/clk/realtek/freq_table.h b/drivers/clk/realtek/freq_table.h
new file mode 100644
index 000000000000..16bf7e3fd489
--- /dev/null
+++ b/drivers/clk/realtek/freq_table.h
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+struct freq_table {
+ u32 val;
+ unsigned long rate;
+};
+
+#define FREQ_TABLE_END \
+ { \
+ .rate = 0 \
+ }
+
+const struct freq_table *ftbl_find_by_rate(const struct freq_table *ftbl,
+ unsigned long rate);
+const struct freq_table *
+ftbl_find_by_val_with_mask(const struct freq_table *ftbl, u32 mask, u32 value);
--
2.43.0
^ permalink raw reply related
* [PATCH v8 07/10] clk: realtek: Add support for MMC-tuned PLL clocks
From: Yu-Chun Lin @ 2026-06-10 8:08 UTC (permalink / raw)
To: mturquette, sboyd, robh, krzk+dt, conor+dt, p.zabel, cylee12,
afaerber, jyanchou
Cc: bmasney, devicetree, linux-clk, linux-kernel, linux-arm-kernel,
linux-realtek-soc, james.tai, cy.huang, stanley_chang,
eleanor.lin
In-Reply-To: <20260610080824.255063-1-eleanor.lin@realtek.com>
From: Cheng-Yu Lee <cylee12@realtek.com>
Add clk_pll_mmc_ops for enable/disable, prepare, rate control, and status
operations on MMC PLL clocks.
Also add clk_pll_mmc_phase_ops to support phase get/set operations.
Signed-off-by: Cheng-Yu Lee <cylee12@realtek.com>
Co-developed-by: Jyan Chou <jyanchou@realtek.com>
Signed-off-by: Jyan Chou <jyanchou@realtek.com>
Co-developed-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com>
---
Changes in v8:
- Fix the mask shift in set_phrt0().
- For better safety and readability, modify pointer comparison for phase_id.
- In clk_pll_mmc_recalc_rate(), return 0 instead of an error code upon failure.
---
MAINTAINERS | 8 +
drivers/clk/realtek/Kconfig | 3 +
drivers/clk/realtek/Makefile | 2 +
drivers/clk/realtek/clk-pll-mmc.c | 459 ++++++++++++++++++++++++++++++
drivers/clk/realtek/clk-pll.h | 13 +
5 files changed, 485 insertions(+)
create mode 100644 drivers/clk/realtek/clk-pll-mmc.c
diff --git a/MAINTAINERS b/MAINTAINERS
index aec1ea6d35d6..52d8099d32a3 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -22489,6 +22489,14 @@ F: drivers/reset/realtek/*
F: include/dt-bindings/clock/realtek*
F: include/dt-bindings/reset/realtek*
+REALTEK SOC PLL CLOCK FOR MMC SUPPORT
+M: Cheng-Yu Lee <cylee12@realtek.com>
+M: Jyan Chou <jyanchou@realtek.com>
+M: Yu-Chun Lin <eleanor.lin@realtek.com>
+L: linux-clk@vger.kernel.org
+S: Supported
+F: drivers/clk/realtek/clk-pll-mmc.c
+
REALTEK SPI-NAND
M: Chris Packham <chris.packham@alliedtelesis.co.nz>
S: Maintained
diff --git a/drivers/clk/realtek/Kconfig b/drivers/clk/realtek/Kconfig
index ed97531e321d..5a832fc3228a 100644
--- a/drivers/clk/realtek/Kconfig
+++ b/drivers/clk/realtek/Kconfig
@@ -27,4 +27,7 @@ config RTK_CLK_COMMON
multiple Realtek clock implementations, and include integration
with reset controllers where required.
+config RTK_CLK_PLL_MMC
+ tristate
+
endif
diff --git a/drivers/clk/realtek/Makefile b/drivers/clk/realtek/Makefile
index f90dc57fcfdb..fd7d777902c8 100644
--- a/drivers/clk/realtek/Makefile
+++ b/drivers/clk/realtek/Makefile
@@ -7,3 +7,5 @@ clk-rtk-y += clk-pll.o
clk-rtk-y += clk-regmap-gate.o
clk-rtk-y += clk-regmap-mux.o
clk-rtk-y += freq_table.o
+
+clk-rtk-$(CONFIG_RTK_CLK_PLL_MMC) += clk-pll-mmc.o
diff --git a/drivers/clk/realtek/clk-pll-mmc.c b/drivers/clk/realtek/clk-pll-mmc.c
new file mode 100644
index 000000000000..c11cb2bd577e
--- /dev/null
+++ b/drivers/clk/realtek/clk-pll-mmc.c
@@ -0,0 +1,459 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2021-2026 Realtek Semiconductor Corporation
+ * Author: Cheng-Yu Lee <cylee12@realtek.com>
+ */
+
+#include <linux/bits.h>
+#include <linux/export.h>
+#include <linux/math64.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include "clk-pll.h"
+
+#define PLL_EMMC1_OFFSET 0x0
+#define PLL_EMMC2_OFFSET 0x4
+#define PLL_EMMC3_OFFSET 0x8
+#define PLL_EMMC4_OFFSET 0xc
+#define PLL_SSC_DIG_EMMC1_OFFSET 0x0
+#define PLL_SSC_DIG_EMMC3_OFFSET 0xc
+#define PLL_SSC_DIG_EMMC4_OFFSET 0x10
+
+#define PLL_MMC_SSC_DIV_N_VAL 0x1b
+
+#define PLL_PHRT0_MASK BIT(0)
+#define PLL_PHSEL_MASK GENMASK(4, 0)
+#define PLL_SSCPLL_RS_MASK GENMASK(12, 10)
+#define PLL_SSCPLL_ICP_MASK GENMASK(9, 5)
+#define PLL_SSC_DIV_EXT_F_MASK GENMASK(25, 13)
+#define PLL_PI_IBSELH_MASK GENMASK(28, 27)
+#define PLL_SSC_DIV_N_MASK GENMASK(23, 16)
+#define PLL_NCODE_SSC_EMMC_MASK GENMASK(20, 13)
+#define PLL_FCODE_SSC_EMMC_MASK GENMASK(12, 0)
+#define PLL_GRAN_EST_EM_MC_MASK GENMASK(20, 0)
+#define PLL_EN_SSC_EMMC_MASK BIT(0)
+#define PLL_FLAG_INITAL_EMMC_MASK BIT(8)
+
+#define PLL_PHRT0_SHIFT 1
+#define PLL_SSCPLL_RS_SHIFT 10
+#define PLL_SSCPLL_ICP_SHIFT 5
+#define PLL_SSC_DIV_EXT_F_SHIFT 13
+#define PLL_PI_IBSELH_SHIFT 27
+#define PLL_SSC_DIV_N_SHIFT 16
+#define PLL_NCODE_SSC_EMMC_SHIFT 13
+#define PLL_FLAG_INITAL_EMMC_SHIFT 8
+
+#define CYCLE_DEGREES 360
+#define PHASE_STEPS 32
+#define PHASE_SCALE_FACTOR 1125
+
+static inline struct clk_pll_mmc *to_clk_pll_mmc(struct clk_hw *hw)
+{
+ struct clk_regmap *clkr = to_clk_regmap(hw);
+
+ return container_of(clkr, struct clk_pll_mmc, clkr);
+}
+
+static inline int get_phrt0(struct clk_pll_mmc *clkm, u32 *val)
+{
+ u32 reg;
+ int ret;
+
+ ret = regmap_read(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC1_OFFSET, ®);
+ if (ret)
+ return ret;
+
+ *val = (reg >> PLL_PHRT0_SHIFT) & PLL_PHRT0_MASK;
+
+ return 0;
+}
+
+static inline int set_phrt0(struct clk_pll_mmc *clkm, u32 val)
+{
+ return regmap_update_bits(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC1_OFFSET,
+ PLL_PHRT0_MASK << PLL_PHRT0_SHIFT, val << PLL_PHRT0_SHIFT);
+}
+
+static inline int get_phsel(struct clk_pll_mmc *clkm, int id, u32 *val)
+{
+ u32 sft = id ? 8 : 3;
+ u32 raw_val;
+ int ret;
+
+ ret = regmap_read(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC1_OFFSET, &raw_val);
+ if (ret)
+ return ret;
+
+ *val = (raw_val >> sft) & PLL_PHSEL_MASK;
+
+ return 0;
+}
+
+static inline int set_phsel(struct clk_pll_mmc *clkm, int id, u32 val)
+{
+ u32 sft = id ? 8 : 3;
+
+ return regmap_update_bits(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC1_OFFSET,
+ PLL_PHSEL_MASK << sft, val << sft);
+}
+
+static inline int set_sscpll_rs(struct clk_pll_mmc *clkm, u32 val)
+{
+ return regmap_update_bits(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC2_OFFSET,
+ PLL_SSCPLL_RS_MASK, val << PLL_SSCPLL_RS_SHIFT);
+}
+
+static inline int set_sscpll_icp(struct clk_pll_mmc *clkm, u32 val)
+{
+ return regmap_update_bits(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC2_OFFSET,
+ PLL_SSCPLL_ICP_MASK, val << PLL_SSCPLL_ICP_SHIFT);
+}
+
+static inline int get_ssc_div_ext_f(struct clk_pll_mmc *clkm, u32 *val)
+{
+ u32 raw_val;
+ int ret;
+
+ ret = regmap_read(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC2_OFFSET, &raw_val);
+ if (ret)
+ return ret;
+
+ *val = (raw_val & PLL_SSC_DIV_EXT_F_MASK) >> PLL_SSC_DIV_EXT_F_SHIFT;
+
+ return 0;
+}
+
+static inline int set_ssc_div_ext_f(struct clk_pll_mmc *clkm, u32 val)
+{
+ return regmap_update_bits(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC2_OFFSET,
+ PLL_SSC_DIV_EXT_F_MASK,
+ val << PLL_SSC_DIV_EXT_F_SHIFT);
+}
+
+static inline int set_pi_ibselh(struct clk_pll_mmc *clkm, u32 val)
+{
+ return regmap_update_bits(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC2_OFFSET,
+ PLL_PI_IBSELH_MASK, val << PLL_PI_IBSELH_SHIFT);
+}
+
+static inline int set_ssc_div_n(struct clk_pll_mmc *clkm, u32 val)
+{
+ return regmap_update_bits(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC3_OFFSET,
+ PLL_SSC_DIV_N_MASK, val << PLL_SSC_DIV_N_SHIFT);
+}
+
+static inline int get_ssc_div_n(struct clk_pll_mmc *clkm, u32 *val)
+{
+ int ret;
+ u32 raw_val;
+
+ ret = regmap_read(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC3_OFFSET, &raw_val);
+ if (ret)
+ return ret;
+
+ *val = (raw_val & PLL_SSC_DIV_N_MASK) >> PLL_SSC_DIV_N_SHIFT;
+
+ return 0;
+}
+
+static inline int set_pow_ctl(struct clk_pll_mmc *clkm, u32 val)
+{
+ return regmap_write(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC4_OFFSET, val);
+}
+
+static inline int get_pow_ctl(struct clk_pll_mmc *clkm, u32 *val)
+{
+ int ret;
+ u32 raw_val;
+
+ ret = regmap_read(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC4_OFFSET, &raw_val);
+ if (ret)
+ return ret;
+
+ *val = raw_val;
+
+ return 0;
+}
+
+static int clk_pll_mmc_phase_set_phase(struct clk_hw *hw, int degrees)
+{
+ struct clk_hw *hwp = clk_hw_get_parent(hw);
+ struct clk_pll_mmc *clkm;
+ int phase_id;
+ int ret;
+ u32 val;
+
+ if (!hwp)
+ return -ENOENT;
+
+ clkm = to_clk_pll_mmc(hwp);
+ phase_id = (hw == &clkm->phase0_hw) ? 0 : 1;
+ val = DIV_ROUND_CLOSEST(degrees * 100, PHASE_SCALE_FACTOR);
+ ret = set_phsel(clkm, phase_id, val);
+ if (ret)
+ return ret;
+
+ usleep_range(10, 20);
+
+ return 0;
+}
+
+static int clk_pll_mmc_phase_get_phase(struct clk_hw *hw)
+{
+ struct clk_hw *hwp;
+ struct clk_pll_mmc *clkm;
+ int phase_id;
+ int ret;
+ u32 val;
+
+ hwp = clk_hw_get_parent(hw);
+ if (!hwp)
+ return -ENOENT;
+
+ clkm = to_clk_pll_mmc(hwp);
+ phase_id = (hw == &clkm->phase0_hw) ? 0 : 1;
+ ret = get_phsel(clkm, phase_id, &val);
+ if (ret)
+ return ret;
+
+ val = DIV_ROUND_CLOSEST(val * CYCLE_DEGREES, PHASE_STEPS);
+
+ return val;
+}
+
+const struct clk_ops rtk_clk_pll_mmc_phase_ops = {
+ .set_phase = clk_pll_mmc_phase_set_phase,
+ .get_phase = clk_pll_mmc_phase_get_phase,
+};
+EXPORT_SYMBOL_NS_GPL(rtk_clk_pll_mmc_phase_ops, "REALTEK_CLK");
+
+static int clk_pll_mmc_prepare(struct clk_hw *hw)
+{
+ struct clk_pll_mmc *clkm = to_clk_pll_mmc(hw);
+
+ return set_pow_ctl(clkm, 7);
+}
+
+static void clk_pll_mmc_unprepare(struct clk_hw *hw)
+{
+ struct clk_pll_mmc *clkm = to_clk_pll_mmc(hw);
+
+ set_pow_ctl(clkm, 0);
+}
+
+static int clk_pll_mmc_is_prepared(struct clk_hw *hw)
+{
+ struct clk_pll_mmc *clkm = to_clk_pll_mmc(hw);
+ u32 val;
+ int ret;
+
+ ret = get_pow_ctl(clkm, &val);
+ if (ret)
+ return 1;
+
+ return val != 0x0;
+}
+
+static int clk_pll_mmc_enable(struct clk_hw *hw)
+{
+ struct clk_pll_mmc *clkm = to_clk_pll_mmc(hw);
+ int ret;
+
+ ret = set_phrt0(clkm, 1);
+ if (ret)
+ return ret;
+
+ udelay(10);
+
+ return 0;
+}
+
+static void clk_pll_mmc_disable(struct clk_hw *hw)
+{
+ struct clk_pll_mmc *clkm = to_clk_pll_mmc(hw);
+
+ set_phrt0(clkm, 0);
+ udelay(10);
+}
+
+static int clk_pll_mmc_is_enabled(struct clk_hw *hw)
+{
+ struct clk_pll_mmc *clkm = to_clk_pll_mmc(hw);
+ u32 val;
+ int ret;
+
+ ret = get_phrt0(clkm, &val);
+ if (ret)
+ return 1;
+
+ return val == 0x1;
+}
+
+static unsigned long clk_pll_mmc_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
+{
+ struct clk_pll_mmc *clkm = to_clk_pll_mmc(hw);
+ u32 val, ext_f;
+ u64 rate, base;
+ int ret;
+
+ ret = get_ssc_div_n(clkm, &val);
+ if (ret)
+ return 0;
+
+ ret = get_ssc_div_ext_f(clkm, &ext_f);
+ if (ret)
+ return 0;
+
+ base = parent_rate / 4;
+ rate = base * (val + 2);
+ rate += div_u64(base * ext_f, 8192);
+
+ return rate;
+}
+
+static int clk_pll_mmc_determine_rate(struct clk_hw *hw, struct clk_rate_request *req)
+{
+ u32 val;
+
+ if (!req->best_parent_rate)
+ return -EINVAL;
+
+ val = DIV_ROUND_CLOSEST(req->rate * 4, req->best_parent_rate);
+ req->rate = req->best_parent_rate * val / 4;
+
+ return 0;
+}
+
+static int clk_pll_mmc_set_rate(struct clk_hw *hw, unsigned long rate, unsigned long parent_rate)
+{
+ struct clk_pll_mmc *clkm = to_clk_pll_mmc(hw);
+ u32 val = PLL_MMC_SSC_DIV_N_VAL;
+ int ret;
+
+ ret = regmap_update_bits(clkm->clkr.regmap,
+ clkm->ssc_dig_ofs + PLL_SSC_DIG_EMMC1_OFFSET,
+ PLL_FLAG_INITAL_EMMC_MASK, 0x0 << PLL_FLAG_INITAL_EMMC_SHIFT);
+ if (ret)
+ return ret;
+
+ ret = set_ssc_div_n(clkm, val);
+ if (ret)
+ return ret;
+
+ ret = set_ssc_div_ext_f(clkm, 1517);
+ if (ret)
+ return ret;
+
+ switch (val) {
+ case 31 ... 46:
+ ret = set_pi_ibselh(clkm, 3);
+ if (ret)
+ return ret;
+
+ ret = set_sscpll_rs(clkm, 3);
+ if (ret)
+ return ret;
+
+ ret = set_sscpll_icp(clkm, 2);
+ if (ret)
+ return ret;
+ break;
+
+ case 20 ... 30:
+ ret = set_pi_ibselh(clkm, 2);
+ if (ret)
+ return ret;
+
+ ret = set_sscpll_rs(clkm, 3);
+ if (ret)
+ return ret;
+
+ ret = set_sscpll_icp(clkm, 1);
+ if (ret)
+ return ret;
+ break;
+
+ case 10 ... 19:
+ ret = set_pi_ibselh(clkm, 1);
+ if (ret)
+ return ret;
+
+ ret = set_sscpll_rs(clkm, 2);
+ if (ret)
+ return ret;
+
+ ret = set_sscpll_icp(clkm, 1);
+ if (ret)
+ return ret;
+ break;
+
+ case 5 ... 9:
+ ret = set_pi_ibselh(clkm, 0);
+ if (ret)
+ return ret;
+
+ ret = set_sscpll_rs(clkm, 2);
+ if (ret)
+ return ret;
+
+ ret = set_sscpll_icp(clkm, 0);
+ if (ret)
+ return ret;
+ break;
+ }
+
+ ret = regmap_update_bits(clkm->clkr.regmap,
+ clkm->ssc_dig_ofs + PLL_SSC_DIG_EMMC3_OFFSET,
+ PLL_NCODE_SSC_EMMC_MASK,
+ 27 << PLL_NCODE_SSC_EMMC_SHIFT);
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(clkm->clkr.regmap,
+ clkm->ssc_dig_ofs + PLL_SSC_DIG_EMMC3_OFFSET,
+ PLL_FCODE_SSC_EMMC_MASK, 321);
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(clkm->clkr.regmap,
+ clkm->ssc_dig_ofs + PLL_SSC_DIG_EMMC4_OFFSET,
+ PLL_GRAN_EST_EM_MC_MASK, 5985);
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(clkm->clkr.regmap,
+ clkm->ssc_dig_ofs + PLL_SSC_DIG_EMMC1_OFFSET,
+ PLL_EN_SSC_EMMC_MASK, 0x1);
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(clkm->clkr.regmap,
+ clkm->ssc_dig_ofs + PLL_SSC_DIG_EMMC1_OFFSET,
+ PLL_EN_SSC_EMMC_MASK, 0x0);
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(clkm->clkr.regmap,
+ clkm->ssc_dig_ofs + PLL_SSC_DIG_EMMC1_OFFSET,
+ PLL_FLAG_INITAL_EMMC_MASK,
+ 0x1 << PLL_FLAG_INITAL_EMMC_SHIFT);
+ if (ret)
+ return ret;
+
+ usleep_range(10, 20);
+
+ return 0;
+}
+
+const struct clk_ops rtk_clk_pll_mmc_ops = {
+ .prepare = clk_pll_mmc_prepare,
+ .unprepare = clk_pll_mmc_unprepare,
+ .is_prepared = clk_pll_mmc_is_prepared,
+ .enable = clk_pll_mmc_enable,
+ .disable = clk_pll_mmc_disable,
+ .is_enabled = clk_pll_mmc_is_enabled,
+ .recalc_rate = clk_pll_mmc_recalc_rate,
+ .determine_rate = clk_pll_mmc_determine_rate,
+ .set_rate = clk_pll_mmc_set_rate,
+};
+EXPORT_SYMBOL_NS_GPL(rtk_clk_pll_mmc_ops, "REALTEK_CLK");
diff --git a/drivers/clk/realtek/clk-pll.h b/drivers/clk/realtek/clk-pll.h
index 59abfa9a6122..192858013384 100644
--- a/drivers/clk/realtek/clk-pll.h
+++ b/drivers/clk/realtek/clk-pll.h
@@ -44,4 +44,17 @@ struct clk_pll {
extern const struct clk_ops rtk_clk_pll_ops;
extern const struct clk_ops rtk_clk_pll_ro_ops;
+struct clk_pll_mmc {
+ struct clk_regmap clkr;
+ unsigned int pll_ofs;
+ unsigned int ssc_dig_ofs;
+ struct clk_hw phase0_hw;
+ struct clk_hw phase1_hw;
+};
+
+#define __clk_pll_mmc_hw(_ptr) __clk_regmap_hw(&(_ptr)->clkr)
+
+extern const struct clk_ops rtk_clk_pll_mmc_ops;
+extern const struct clk_ops rtk_clk_pll_mmc_phase_ops;
+
#endif /* __CLK_REALTEK_CLK_PLL_H */
--
2.43.0
^ permalink raw reply related
* [PATCH v8 01/10] dt-bindings: clock: Add Realtek RTD1625 Clock & Reset Controller
From: Yu-Chun Lin @ 2026-06-10 8:08 UTC (permalink / raw)
To: mturquette, sboyd, robh, krzk+dt, conor+dt, p.zabel, cylee12,
afaerber, jyanchou
Cc: bmasney, devicetree, linux-clk, linux-kernel, linux-arm-kernel,
linux-realtek-soc, james.tai, cy.huang, stanley_chang,
eleanor.lin, Krzysztof Kozlowski
In-Reply-To: <20260610080824.255063-1-eleanor.lin@realtek.com>
Add DT binding schema for Realtek RTD1625 clock and reset controller
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Co-developed-by: Cheng-Yu Lee <cylee12@realtek.com>
Signed-off-by: Cheng-Yu Lee <cylee12@realtek.com>
Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com>
---
Changes in v8:
- None
---
.../bindings/clock/realtek,rtd1625-clk.yaml | 58 ++++++
MAINTAINERS | 10 +
.../dt-bindings/clock/realtek,rtd1625-clk.h | 164 +++++++++++++++++
include/dt-bindings/reset/realtek,rtd1625.h | 171 ++++++++++++++++++
4 files changed, 403 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/realtek,rtd1625-clk.yaml
create mode 100644 include/dt-bindings/clock/realtek,rtd1625-clk.h
create mode 100644 include/dt-bindings/reset/realtek,rtd1625.h
diff --git a/Documentation/devicetree/bindings/clock/realtek,rtd1625-clk.yaml b/Documentation/devicetree/bindings/clock/realtek,rtd1625-clk.yaml
new file mode 100644
index 000000000000..1aceef31e148
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/realtek,rtd1625-clk.yaml
@@ -0,0 +1,58 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/realtek,rtd1625-clk.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Realtek RTD1625 Clock & Reset Controller
+
+maintainers:
+ - Cheng-Yu Lee <cylee12@realtek.com>
+ - Yu-Chun Lin <eleanor.lin@realtek.com>
+
+description: |
+ The Realtek RTD1625 Clock Controller manages and distributes clock
+ signals to various controllers and implements a Reset Controller for the
+ SoC peripherals.
+
+ Clocks and resets are referenced by unique identifiers, which are defined as
+ preprocessor macros in include/dt-bindings/clock/realtek,rtd1625-clk.h and
+ include/dt-bindings/reset/realtek,rtd1625.h.
+
+properties:
+ compatible:
+ enum:
+ - realtek,rtd1625-crt-clk
+ - realtek,rtd1625-iso-clk
+ - realtek,rtd1625-iso-s-clk
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ "#clock-cells":
+ const: 1
+
+ "#reset-cells":
+ const: 1
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - "#clock-cells"
+ - "#reset-cells"
+
+additionalProperties: false
+
+examples:
+ - |
+ clock-controller@98000000 {
+ compatible = "realtek,rtd1625-crt-clk";
+ reg = <0x98000000 0x1000>;
+ clocks = <&osc27m>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 355e4ab2f9e5..613ca7e95e47 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -22477,6 +22477,16 @@ S: Maintained
F: Documentation/devicetree/bindings/net/dsa/realtek.yaml
F: drivers/net/dsa/realtek/*
+REALTEK SOC CLOCK AND RESET DRIVERS
+M: Cheng-Yu Lee <cylee12@realtek.com>
+M: Yu-Chun Lin <eleanor.lin@realtek.com>
+L: devicetree@vger.kernel.org
+L: linux-clk@vger.kernel.org
+S: Supported
+F: Documentation/devicetree/bindings/clock/realtek*
+F: include/dt-bindings/clock/realtek*
+F: include/dt-bindings/reset/realtek*
+
REALTEK SPI-NAND
M: Chris Packham <chris.packham@alliedtelesis.co.nz>
S: Maintained
diff --git a/include/dt-bindings/clock/realtek,rtd1625-clk.h b/include/dt-bindings/clock/realtek,rtd1625-clk.h
new file mode 100644
index 000000000000..61ca652d6880
--- /dev/null
+++ b/include/dt-bindings/clock/realtek,rtd1625-clk.h
@@ -0,0 +1,164 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright (C) 2025 Realtek Semiconductor Corp.
+ */
+#ifndef __DT_BINDINGS_RTK_CLOCK_RTD1625_H
+#define __DT_BINDINGS_RTK_CLOCK_RTD1625_H
+
+#define RTD1625_CRT_CLK_EN_MISC 0
+#define RTD1625_CRT_CLK_EN_PCIE0 1
+#define RTD1625_CRT_CLK_EN_DIP 2
+#define RTD1625_CRT_CLK_EN_GSPI 3
+#define RTD1625_CRT_CLK_EN_ISO_MISC 5
+#define RTD1625_CRT_CLK_EN_SDS 6
+#define RTD1625_CRT_CLK_EN_HDMI 7
+#define RTD1625_CRT_CLK_EN_GPU 9
+#define RTD1625_CRT_CLK_EN_VE1 10
+#define RTD1625_CRT_CLK_EN_VE2 11
+#define RTD1625_CRT_CLK_EN_MD 18
+#define RTD1625_CRT_CLK_EN_TP 19
+#define RTD1625_CRT_CLK_EN_RCIC 20
+#define RTD1625_CRT_CLK_EN_NF 21
+#define RTD1625_CRT_CLK_EN_EMMC 22
+#define RTD1625_CRT_CLK_EN_SD 23
+#define RTD1625_CRT_CLK_EN_SDIO_IP 24
+#define RTD1625_CRT_CLK_EN_MIPI_CSI 25
+#define RTD1625_CRT_CLK_EN_EMMC_IP 26
+#define RTD1625_CRT_CLK_EN_SDIO 27
+#define RTD1625_CRT_CLK_EN_SD_IP 28
+#define RTD1625_CRT_CLK_EN_TPB 30
+#define RTD1625_CRT_CLK_EN_MISC_SC1 31
+#define RTD1625_CRT_CLK_EN_MISC_I2C_3 32
+#define RTD1625_CRT_CLK_EN_ACPU 33
+#define RTD1625_CRT_CLK_EN_JPEG 34
+#define RTD1625_CRT_CLK_EN_MISC_SC0 37
+#define RTD1625_CRT_CLK_EN_HDMIRX 45
+#define RTD1625_CRT_CLK_EN_HSE 46
+#define RTD1625_CRT_CLK_EN_FAN 49
+#define RTD1625_CRT_CLK_EN_SATA_WRAP_SYS 52
+#define RTD1625_CRT_CLK_EN_SATA_WRAP_SYSH 53
+#define RTD1625_CRT_CLK_EN_SATA_MAC_SYSH 54
+#define RTD1625_CRT_CLK_EN_R2RDSC 55
+#define RTD1625_CRT_CLK_EN_TPC 56
+#define RTD1625_CRT_CLK_EN_PCIE1 57
+#define RTD1625_CRT_CLK_EN_MISC_I2C_4 58
+#define RTD1625_CRT_CLK_EN_MISC_I2C_5 59
+#define RTD1625_CRT_CLK_EN_TSIO 60
+#define RTD1625_CRT_CLK_EN_VE4 61
+#define RTD1625_CRT_CLK_EN_EDP 62
+#define RTD1625_CRT_CLK_EN_TSIO_TRX 63
+#define RTD1625_CRT_CLK_EN_PCIE2 64
+#define RTD1625_CRT_CLK_EN_EARC 66
+#define RTD1625_CRT_CLK_EN_LITE 67
+#define RTD1625_CRT_CLK_EN_MIPI_DSI 68
+#define RTD1625_CRT_CLK_EN_NPUPP 69
+#define RTD1625_CRT_CLK_EN_NPU 70
+#define RTD1625_CRT_CLK_EN_AUCPU0 71
+#define RTD1625_CRT_CLK_EN_AUCPU1 72
+#define RTD1625_CRT_CLK_EN_NSRAM 73
+#define RTD1625_CRT_CLK_EN_HDMITOP 74
+#define RTD1625_CRT_CLK_EN_AUCPU_ISO_NPU 76
+#define RTD1625_CRT_CLK_EN_KEYLADDER 77
+#define RTD1625_CRT_CLK_EN_IFCP_KLM 78
+#define RTD1625_CRT_CLK_EN_IFCP 79
+#define RTD1625_CRT_CLK_EN_MDL_GENPW 80
+#define RTD1625_CRT_CLK_EN_MDL_CHIP 81
+#define RTD1625_CRT_CLK_EN_MDL_IP 82
+#define RTD1625_CRT_CLK_EN_MDLM2M 83
+#define RTD1625_CRT_CLK_EN_MDL_XTAL 84
+#define RTD1625_CRT_CLK_EN_TEST_MUX 85
+#define RTD1625_CRT_CLK_EN_DLA 86
+#define RTD1625_CRT_CLK_EN_TPCW 88
+#define RTD1625_CRT_CLK_EN_GPU_TS_SRC 89
+#define RTD1625_CRT_CLK_EN_VI 91
+#define RTD1625_CRT_CLK_EN_LVDS1 92
+#define RTD1625_CRT_CLK_EN_LVDS2 93
+#define RTD1625_CRT_CLK_EN_AUCPU 94
+#define RTD1625_CRT_CLK_EN_UR1 96
+#define RTD1625_CRT_CLK_EN_UR2 97
+#define RTD1625_CRT_CLK_EN_UR3 98
+#define RTD1625_CRT_CLK_EN_UR4 99
+#define RTD1625_CRT_CLK_EN_UR5 100
+#define RTD1625_CRT_CLK_EN_UR6 101
+#define RTD1625_CRT_CLK_EN_UR7 102
+#define RTD1625_CRT_CLK_EN_UR8 103
+#define RTD1625_CRT_CLK_EN_UR9 104
+#define RTD1625_CRT_CLK_EN_UR_TOP 105
+#define RTD1625_CRT_CLK_EN_MISC_I2C_7 110
+#define RTD1625_CRT_CLK_EN_MISC_I2C_6 111
+#define RTD1625_CRT_CLK_EN_SPI0 112
+#define RTD1625_CRT_CLK_EN_SPI1 113
+#define RTD1625_CRT_CLK_EN_SPI2 114
+#define RTD1625_CRT_CLK_EN_LSADC0 120
+#define RTD1625_CRT_CLK_EN_LSADC1 121
+#define RTD1625_CRT_CLK_EN_ISOMIS_DMA 122
+#define RTD1625_CRT_CLK_EN_DPTX 124
+#define RTD1625_CRT_CLK_EN_NPU_MIPI_CSI 125
+#define RTD1625_CRT_CLK_EN_EDPTX 126
+#define RTD1625_CRT_CLK_HIFI 128
+#define RTD1625_CRT_CLK_NPU_MIPI_CSI 129
+#define RTD1625_CRT_CLK_NPU 130
+#define RTD1625_CRT_CLK_NPU_SYSH 132
+#define RTD1625_CRT_CLK_HIFI_SCPU 133
+#define RTD1625_CRT_CLK_GPU 134
+#define RTD1625_CRT_CLK_GPU2D 135
+#define RTD1625_CRT_CLK_MIPI_DSI_PCLK 136
+#define RTD1625_CRT_CLK_VE1 137
+#define RTD1625_CRT_CLK_VE2 138
+#define RTD1625_CRT_CLK_VE4 139
+#define RTD1625_CRT_CLK_SYS 141
+#define RTD1625_CRT_CLK_SYSH 142
+#define RTD1625_CRT_PLL_SDIO_REF 145
+#define RTD1625_CRT_PLL_CR_REF 146
+#define RTD1625_CRT_PLL_EMMC_REF 147
+#define RTD1625_CRT_CLK_MIS_SC0 148
+#define RTD1625_CRT_CLK_MIS_SC1 149
+#define RTD1625_CRT_PLL_SCPU 150
+#define RTD1625_CRT_PLL_VE1 151
+#define RTD1625_CRT_PLL_DDSA 152
+#define RTD1625_CRT_PLL_PSAUDA1 153
+#define RTD1625_CRT_PLL_PSAUDA2 154
+#define RTD1625_CRT_PLL_BUS 155
+#define RTD1625_CRT_PLL_SDIO 156
+#define RTD1625_CRT_PLL_SDIO_VP0 157
+#define RTD1625_CRT_PLL_SDIO_VP1 158
+#define RTD1625_CRT_PLL_DCSB 159
+#define RTD1625_CRT_PLL_GPU 160
+#define RTD1625_CRT_PLL_NPU 161
+#define RTD1625_CRT_PLL_VE2 162
+#define RTD1625_CRT_PLL_HIFI 163
+#define RTD1625_CRT_PLL_SD 164
+#define RTD1625_CRT_PLL_SD_VP0 165
+#define RTD1625_CRT_PLL_SD_VP1 166
+#define RTD1625_CRT_PLL_EMMC 167
+#define RTD1625_CRT_PLL_EMMC_VP0 168
+#define RTD1625_CRT_PLL_EMMC_VP1 169
+#define RTD1625_CRT_PLL_ACPU 170
+#define RTD1625_CRT_CLK_DET 171
+
+#define RTD1625_ISO_CLK_EN_USB_P4 0
+#define RTD1625_ISO_CLK_EN_USB_P3 1
+#define RTD1625_ISO_CLK_EN_MISC_CEC0 2
+#define RTD1625_ISO_CLK_EN_CBUSRX_SYS 3
+#define RTD1625_ISO_CLK_EN_CBUSTX_SYS 4
+#define RTD1625_ISO_CLK_EN_CBUS_SYS 5
+#define RTD1625_ISO_CLK_EN_CBUS_OSC 6
+#define RTD1625_ISO_CLK_EN_MISC_UR0 8
+#define RTD1625_ISO_CLK_EN_I2C0 9
+#define RTD1625_ISO_CLK_EN_I2C1 10
+#define RTD1625_ISO_CLK_EN_ETN_250M 11
+#define RTD1625_ISO_CLK_EN_ETN_SYS 12
+#define RTD1625_ISO_CLK_EN_USB_DRD 13
+#define RTD1625_ISO_CLK_EN_USB_HOST 14
+#define RTD1625_ISO_CLK_EN_USB_U3_HOST 15
+#define RTD1625_ISO_CLK_EN_USB 16
+#define RTD1625_ISO_CLK_EN_VTC 17
+#define RTD1625_ISO_CLK_EN_MISC_VFD 18
+
+#define RTD1625_ISO_S_CLK_EN_ISOM_MIS 0
+#define RTD1625_ISO_S_CLK_EN_ISOM_GPIOM 1
+#define RTD1625_ISO_S_CLK_EN_TIMER7 2
+#define RTD1625_ISO_S_CLK_EN_IRDA 3
+#define RTD1625_ISO_S_CLK_EN_UR10 4
+
+#endif /* __DT_BINDINGS_RTK_CLOCK_RTD1625_H */
diff --git a/include/dt-bindings/reset/realtek,rtd1625.h b/include/dt-bindings/reset/realtek,rtd1625.h
new file mode 100644
index 000000000000..31e7fa66ef31
--- /dev/null
+++ b/include/dt-bindings/reset/realtek,rtd1625.h
@@ -0,0 +1,171 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright (C) 2025 Realtek Semiconductor Corp.
+ */
+
+#ifndef __DT_BINDINGS_RTK_RESET_RTD1625_H
+#define __DT_BINDINGS_RTK_RESET_RTD1625_H
+
+#define RTD1625_CRT_RSTN_MISC 0
+#define RTD1625_CRT_RSTN_DIP 1
+#define RTD1625_CRT_RSTN_GSPI 2
+#define RTD1625_CRT_RSTN_SDS 3
+#define RTD1625_CRT_RSTN_SDS_REG 4
+#define RTD1625_CRT_RSTN_SDS_PHY 5
+#define RTD1625_CRT_RSTN_GPU2D 6
+#define RTD1625_CRT_RSTN_DC_PHY 7
+#define RTD1625_CRT_RSTN_DCPHY_CRT 8
+#define RTD1625_CRT_RSTN_LSADC 9
+#define RTD1625_CRT_RSTN_SE 10
+#define RTD1625_CRT_RSTN_DLA 11
+#define RTD1625_CRT_RSTN_JPEG 12
+#define RTD1625_CRT_RSTN_SD 13
+#define RTD1625_CRT_RSTN_SDIO 14
+#define RTD1625_CRT_RSTN_PCR_CNT 15
+#define RTD1625_CRT_RSTN_PCIE0_STITCH 16
+#define RTD1625_CRT_RSTN_PCIE0_PHY 17
+#define RTD1625_CRT_RSTN_PCIE0 18
+#define RTD1625_CRT_RSTN_PCIE0_CORE 19
+#define RTD1625_CRT_RSTN_PCIE0_POWER 20
+#define RTD1625_CRT_RSTN_PCIE0_NONSTICH 21
+#define RTD1625_CRT_RSTN_PCIE0_PHY_MDIO 22
+#define RTD1625_CRT_RSTN_PCIE0_SGMII_MDIO 23
+#define RTD1625_CRT_RSTN_VO2 24
+#define RTD1625_CRT_RSTN_MISC_SC0 25
+#define RTD1625_CRT_RSTN_MD 26
+#define RTD1625_CRT_RSTN_LVDS1 27
+#define RTD1625_CRT_RSTN_LVDS2 28
+#define RTD1625_CRT_RSTN_MISC_SC1 29
+#define RTD1625_CRT_RSTN_I2C_3 30
+#define RTD1625_CRT_RSTN_FAN 31
+#define RTD1625_CRT_RSTN_TVE 32
+#define RTD1625_CRT_RSTN_AIO 33
+#define RTD1625_CRT_RSTN_VO 34
+#define RTD1625_CRT_RSTN_MIPI_CSI 35
+#define RTD1625_CRT_RSTN_HDMIRX 36
+#define RTD1625_CRT_RSTN_HDMIRX_WRAP 37
+#define RTD1625_CRT_RSTN_HDMI 38
+#define RTD1625_CRT_RSTN_DISP 39
+#define RTD1625_CRT_RSTN_SATA_PHY_POW1 40
+#define RTD1625_CRT_RSTN_SATA_PHY_POW0 41
+#define RTD1625_CRT_RSTN_SATA_MDIO1 42
+#define RTD1625_CRT_RSTN_SATA_MDIO0 43
+#define RTD1625_CRT_RSTN_SATA_WRAP 44
+#define RTD1625_CRT_RSTN_SATA_MAC_P1 45
+#define RTD1625_CRT_RSTN_SATA_MAC_P0 46
+#define RTD1625_CRT_RSTN_SATA_MAC_COM 47
+#define RTD1625_CRT_RSTN_PCIE1_STITCH 48
+#define RTD1625_CRT_RSTN_PCIE1_PHY 49
+#define RTD1625_CRT_RSTN_PCIE1 50
+#define RTD1625_CRT_RSTN_PCIE1_CORE 51
+#define RTD1625_CRT_RSTN_PCIE1_POWER 52
+#define RTD1625_CRT_RSTN_PCIE1_NONSTICH 53
+#define RTD1625_CRT_RSTN_PCIE1_PHY_MDIO 54
+#define RTD1625_CRT_RSTN_HDMITOP 55
+#define RTD1625_CRT_RSTN_I2C_4 56
+#define RTD1625_CRT_RSTN_I2C_5 57
+#define RTD1625_CRT_RSTN_TSIO 58
+#define RTD1625_CRT_RSTN_VI 59
+#define RTD1625_CRT_RSTN_EDP 60
+#define RTD1625_CRT_RSTN_VE1_MMU 61
+#define RTD1625_CRT_RSTN_VE1_MMU_FUNC 62
+#define RTD1625_CRT_RSTN_HSE_MMU 63
+#define RTD1625_CRT_RSTN_HSE_MMU_FUNC 64
+#define RTD1625_CRT_RSTN_MDLM2M 65
+#define RTD1625_CRT_RSTN_ISO_GSPI 66
+#define RTD1625_CRT_RSTN_SOFT_NPU 67
+#define RTD1625_CRT_RSTN_SPI2EMMC 68
+#define RTD1625_CRT_RSTN_EARC 69
+#define RTD1625_CRT_RSTN_VE1 70
+#define RTD1625_CRT_RSTN_PCIE2_STITCH 71
+#define RTD1625_CRT_RSTN_PCIE2_PHY 72
+#define RTD1625_CRT_RSTN_PCIE2 73
+#define RTD1625_CRT_RSTN_PCIE2_CORE 74
+#define RTD1625_CRT_RSTN_PCIE2_POWER 75
+#define RTD1625_CRT_RSTN_PCIE2_NONSTICH 76
+#define RTD1625_CRT_RSTN_PCIE2_PHY_MDIO 77
+#define RTD1625_CRT_RSTN_DCPHY_UMCTL2 78
+#define RTD1625_CRT_RSTN_MIPI_DSI 79
+#define RTD1625_CRT_RSTN_HIFM 80
+#define RTD1625_CRT_RSTN_NSRAM 81
+#define RTD1625_CRT_RSTN_AUCPU0_REG 82
+#define RTD1625_CRT_RSTN_MDL_GENPW 83
+#define RTD1625_CRT_RSTN_MDL_CHIP 84
+#define RTD1625_CRT_RSTN_MDL_IP 85
+#define RTD1625_CRT_RSTN_TEST_MUX 86
+#define RTD1625_CRT_RSTN_ISO_BIST 87
+#define RTD1625_CRT_RSTN_MAIN_BIST 88
+#define RTD1625_CRT_RSTN_MAIN2_BIST 89
+#define RTD1625_CRT_RSTN_VE1_BIST 90
+#define RTD1625_CRT_RSTN_VE2_BIST 91
+#define RTD1625_CRT_RSTN_DCPHY_BIST 92
+#define RTD1625_CRT_RSTN_GPU_BIST 93
+#define RTD1625_CRT_RSTN_DISP_BIST 94
+#define RTD1625_CRT_RSTN_NPU_BIST 95
+#define RTD1625_CRT_RSTN_CAS_BIST 96
+#define RTD1625_CRT_RSTN_VE4_BIST 97
+#define RTD1625_CRT_RSTN_EMMC 98
+#define RTD1625_CRT_RSTN_GPU 99
+#define RTD1625_CRT_RSTN_VE2 100
+#define RTD1625_CRT_RSTN_UR1 101
+#define RTD1625_CRT_RSTN_UR2 102
+#define RTD1625_CRT_RSTN_UR3 103
+#define RTD1625_CRT_RSTN_UR4 104
+#define RTD1625_CRT_RSTN_UR5 105
+#define RTD1625_CRT_RSTN_UR6 106
+#define RTD1625_CRT_RSTN_UR7 107
+#define RTD1625_CRT_RSTN_UR8 108
+#define RTD1625_CRT_RSTN_UR9 109
+#define RTD1625_CRT_RSTN_UR_TOP 110
+#define RTD1625_CRT_RSTN_I2C_7 111
+#define RTD1625_CRT_RSTN_I2C_6 112
+#define RTD1625_CRT_RSTN_SPI0 113
+#define RTD1625_CRT_RSTN_SPI1 114
+#define RTD1625_CRT_RSTN_SPI2 115
+#define RTD1625_CRT_RSTN_LSADC0 116
+#define RTD1625_CRT_RSTN_LSADC1 117
+#define RTD1625_CRT_RSTN_ISOMIS_DMA 118
+#define RTD1625_CRT_RSTN_AUDIO_ADC 119
+#define RTD1625_CRT_RSTN_DPTX 120
+#define RTD1625_CRT_RSTN_AUCPU1_REG 121
+#define RTD1625_CRT_RSTN_EDPTX 122
+
+/* ISO reset */
+#define RTD1625_ISO_RSTN_VFD 0
+#define RTD1625_ISO_RSTN_CEC0 1
+#define RTD1625_ISO_RSTN_CEC1 2
+#define RTD1625_ISO_RSTN_CBUSTX 3
+#define RTD1625_ISO_RSTN_CBUSRX 4
+#define RTD1625_ISO_RSTN_USB3_PHY2_XTAL_POW 5
+#define RTD1625_ISO_RSTN_UR0 6
+#define RTD1625_ISO_RSTN_GMAC 7
+#define RTD1625_ISO_RSTN_GPHY 8
+#define RTD1625_ISO_RSTN_I2C_0 9
+#define RTD1625_ISO_RSTN_I2C_1 10
+#define RTD1625_ISO_RSTN_CBUS 11
+#define RTD1625_ISO_RSTN_USB_DRD 12
+#define RTD1625_ISO_RSTN_USB_HOST 13
+#define RTD1625_ISO_RSTN_USB_PHY_0 14
+#define RTD1625_ISO_RSTN_USB_PHY_1 15
+#define RTD1625_ISO_RSTN_USB_PHY_2 16
+#define RTD1625_ISO_RSTN_USB 17
+#define RTD1625_ISO_RSTN_TYPE_C 18
+#define RTD1625_ISO_RSTN_USB_U3_HOST 19
+#define RTD1625_ISO_RSTN_USB3_PHY0_POW 20
+#define RTD1625_ISO_RSTN_USB3_P0_MDIO 21
+#define RTD1625_ISO_RSTN_USB3_PHY1_POW 22
+#define RTD1625_ISO_RSTN_USB3_P1_MDIO 23
+#define RTD1625_ISO_RSTN_VTC 24
+#define RTD1625_ISO_RSTN_USB3_PHY2_POW 25
+#define RTD1625_ISO_RSTN_USB3_P2_MDIO 26
+#define RTD1625_ISO_RSTN_USB_PHY_3 27
+#define RTD1625_ISO_RSTN_USB_PHY_4 28
+
+/* ISO_S reset */
+#define RTD1625_ISO_S_RSTN_ISOM_MIS 0
+#define RTD1625_ISO_S_RSTN_GPIOM 1
+#define RTD1625_ISO_S_RSTN_TIMER7 2
+#define RTD1625_ISO_S_RSTN_IRDA 3
+#define RTD1625_ISO_S_RSTN_UR10 4
+
+#endif /* __DT_BINDINGS_RTK_RESET_RTD1625_H */
--
2.43.0
^ permalink raw reply related
* [PATCH v8 09/10] clk: realtek: Add RTD1625-ISO clock controller driver
From: Yu-Chun Lin @ 2026-06-10 8:08 UTC (permalink / raw)
To: mturquette, sboyd, robh, krzk+dt, conor+dt, p.zabel, cylee12,
afaerber, jyanchou
Cc: bmasney, devicetree, linux-clk, linux-kernel, linux-arm-kernel,
linux-realtek-soc, james.tai, cy.huang, stanley_chang,
eleanor.lin
In-Reply-To: <20260610080824.255063-1-eleanor.lin@realtek.com>
From: Cheng-Yu Lee <cylee12@realtek.com>
Add support for the ISO (Isolation) domain clock controller on the Realtek
RTD1625 SoC. This controller manages clocks in the always-on power domain,
ensuring essential services remain functional even when the main system
power is gated.
Since the reset controller shares the same register space with the ISO
clock controller, it is instantiated as an auxiliary device by the core
clock driver. This patch also includes the corresponding auxiliary reset
driver to handle the ISO domain resets.
Signed-off-by: Cheng-Yu Lee <cylee12@realtek.com>
Co-developed-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com>
---
Changes in v8:
- Remove the trailing NULL element ([RTD1625_XX_CLK_MAX] = NULL) from the
clk_hw_onecell_data arrays.
- Add MODULE_DEVICE_TABLE(of, ...) for the tristate config.
- Add `.suppress_bind_attrs = true`, to avoid handling pointer problem, cause
clock should not allow to manually disable by users.
- Fix a typo.
---
drivers/clk/realtek/Makefile | 1 +
drivers/clk/realtek/clk-rtd1625-iso.c | 151 ++++++++++++++++++++++
drivers/reset/realtek/Makefile | 2 +-
drivers/reset/realtek/reset-rtd1625-iso.c | 99 ++++++++++++++
4 files changed, 252 insertions(+), 1 deletion(-)
create mode 100644 drivers/clk/realtek/clk-rtd1625-iso.c
create mode 100644 drivers/reset/realtek/reset-rtd1625-iso.c
diff --git a/drivers/clk/realtek/Makefile b/drivers/clk/realtek/Makefile
index f4a62be092d2..7627eb67ab66 100644
--- a/drivers/clk/realtek/Makefile
+++ b/drivers/clk/realtek/Makefile
@@ -10,3 +10,4 @@ clk-rtk-y += freq_table.o
clk-rtk-$(CONFIG_RTK_CLK_PLL_MMC) += clk-pll-mmc.o
obj-$(CONFIG_CLK_RTD1625) += clk-rtd1625-crt.o
+obj-$(CONFIG_CLK_RTD1625) += clk-rtd1625-iso.o
diff --git a/drivers/clk/realtek/clk-rtd1625-iso.c b/drivers/clk/realtek/clk-rtd1625-iso.c
new file mode 100644
index 000000000000..52c4a4304284
--- /dev/null
+++ b/drivers/clk/realtek/clk-rtd1625-iso.c
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2024-2026 Realtek Semiconductor Corporation
+ * Author: Cheng-Yu Lee <cylee12@realtek.com>
+ */
+
+#include <dt-bindings/clock/realtek,rtd1625-clk.h>
+#include <linux/array_size.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include "clk-regmap-gate.h"
+
+#define RTD1625_ISO_CLK_MAX 19
+#define RTD1625_ISO_RSTN_MAX 29
+#define RTD1625_ISO_S_CLK_MAX 5
+#define RTD1625_ISO_S_RSTN_MAX 5
+
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_usb_p4, 0, 0x4, 0, 0);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_usb_p3, 0, 0x4, 1, 0);
+static CLK_REGMAP_GATE(clk_en_misc_cec0, "clk_en_misc", 0, 0x4, 2, 0);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_cbusrx_sys, 0, 0x4, 3, 0);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_cbustx_sys, 0, 0x4, 4, 0);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_cbus_sys, 0, 0x4, 5, 0);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_cbus_osc, 0, 0x4, 6, 0);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_i2c0, 0, 0x4, 9, 0);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_i2c1, 0, 0x4, 10, 0);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_etn_250m, 0, 0x4, 11, 0);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_etn_sys, 0, 0x4, 12, 0);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_usb_drd, 0, 0x4, 13, 0);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_usb_host, 0, 0x4, 14, 0);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_usb_u3_host, 0, 0x4, 15, 0);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_usb, 0, 0x4, 16, 0);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_vtc, 0, 0x4, 17, 0);
+static CLK_REGMAP_GATE(clk_en_misc_vfd, "clk_en_misc", 0, 0x4, 18, 0);
+
+static struct clk_regmap * const rtd1625_clk_regmap_list[] = {
+ &clk_en_usb_p4.clkr,
+ &clk_en_usb_p3.clkr,
+ &clk_en_misc_cec0.clkr,
+ &clk_en_cbusrx_sys.clkr,
+ &clk_en_cbustx_sys.clkr,
+ &clk_en_cbus_sys.clkr,
+ &clk_en_cbus_osc.clkr,
+ &clk_en_i2c0.clkr,
+ &clk_en_i2c1.clkr,
+ &clk_en_etn_250m.clkr,
+ &clk_en_etn_sys.clkr,
+ &clk_en_usb_drd.clkr,
+ &clk_en_usb_host.clkr,
+ &clk_en_usb_u3_host.clkr,
+ &clk_en_usb.clkr,
+ &clk_en_vtc.clkr,
+ &clk_en_misc_vfd.clkr,
+};
+
+static struct clk_hw_onecell_data rtd1625_iso_clk_data = {
+ .num = RTD1625_ISO_CLK_MAX,
+ .hws = {
+ [RTD1625_ISO_CLK_EN_USB_P4] = &__clk_regmap_gate_hw(&clk_en_usb_p4),
+ [RTD1625_ISO_CLK_EN_USB_P3] = &__clk_regmap_gate_hw(&clk_en_usb_p3),
+ [RTD1625_ISO_CLK_EN_MISC_CEC0] = &__clk_regmap_gate_hw(&clk_en_misc_cec0),
+ [RTD1625_ISO_CLK_EN_CBUSRX_SYS] = &__clk_regmap_gate_hw(&clk_en_cbusrx_sys),
+ [RTD1625_ISO_CLK_EN_CBUSTX_SYS] = &__clk_regmap_gate_hw(&clk_en_cbustx_sys),
+ [RTD1625_ISO_CLK_EN_CBUS_SYS] = &__clk_regmap_gate_hw(&clk_en_cbus_sys),
+ [RTD1625_ISO_CLK_EN_CBUS_OSC] = &__clk_regmap_gate_hw(&clk_en_cbus_osc),
+ [RTD1625_ISO_CLK_EN_I2C0] = &__clk_regmap_gate_hw(&clk_en_i2c0),
+ [RTD1625_ISO_CLK_EN_I2C1] = &__clk_regmap_gate_hw(&clk_en_i2c1),
+ [RTD1625_ISO_CLK_EN_ETN_250M] = &__clk_regmap_gate_hw(&clk_en_etn_250m),
+ [RTD1625_ISO_CLK_EN_ETN_SYS] = &__clk_regmap_gate_hw(&clk_en_etn_sys),
+ [RTD1625_ISO_CLK_EN_USB_DRD] = &__clk_regmap_gate_hw(&clk_en_usb_drd),
+ [RTD1625_ISO_CLK_EN_USB_HOST] = &__clk_regmap_gate_hw(&clk_en_usb_host),
+ [RTD1625_ISO_CLK_EN_USB_U3_HOST] = &__clk_regmap_gate_hw(&clk_en_usb_u3_host),
+ [RTD1625_ISO_CLK_EN_USB] = &__clk_regmap_gate_hw(&clk_en_usb),
+ [RTD1625_ISO_CLK_EN_VTC] = &__clk_regmap_gate_hw(&clk_en_vtc),
+ [RTD1625_ISO_CLK_EN_MISC_VFD] = &__clk_regmap_gate_hw(&clk_en_misc_vfd),
+ },
+};
+
+static const struct rtk_clk_desc rtd1625_iso_desc = {
+ .clk_data = &rtd1625_iso_clk_data,
+ .clks = rtd1625_clk_regmap_list,
+ .num_clks = ARRAY_SIZE(rtd1625_clk_regmap_list),
+};
+
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_irda, 0, 0x4, 6, 1);
+static CLK_REGMAP_GATE_NO_PARENT(clk_en_ur10, 0, 0x4, 8, 1);
+
+static struct clk_regmap * const rtd1625_iso_s_clk_regmap_list[] = {
+ &clk_en_irda.clkr,
+ &clk_en_ur10.clkr,
+};
+
+static struct clk_hw_onecell_data rtd1625_iso_s_clk_data = {
+ .num = RTD1625_ISO_S_CLK_MAX,
+ .hws = {
+ [RTD1625_ISO_S_CLK_EN_IRDA] = &__clk_regmap_gate_hw(&clk_en_irda),
+ [RTD1625_ISO_S_CLK_EN_UR10] = &__clk_regmap_gate_hw(&clk_en_ur10),
+ },
+};
+
+static const struct rtk_clk_desc rtd1625_iso_s_desc = {
+ .clk_data = &rtd1625_iso_s_clk_data,
+ .clks = rtd1625_iso_s_clk_regmap_list,
+ .num_clks = ARRAY_SIZE(rtd1625_iso_s_clk_regmap_list),
+};
+
+static int rtd1625_iso_probe(struct platform_device *pdev)
+{
+ const struct rtk_clk_desc *desc;
+ const char *aux_name = NULL;
+
+ desc = of_device_get_match_data(&pdev->dev);
+ if (!desc)
+ return -EINVAL;
+
+ if (of_device_is_compatible(pdev->dev.of_node, "realtek,rtd1625-iso-clk"))
+ aux_name = "iso_rst";
+ else
+ aux_name = "iso_s_rst";
+
+ return rtk_clk_probe(pdev, desc, aux_name);
+}
+
+static const struct of_device_id rtd1625_iso_match[] = {
+ {.compatible = "realtek,rtd1625-iso-clk", .data = &rtd1625_iso_desc},
+ {.compatible = "realtek,rtd1625-iso-s-clk", .data = &rtd1625_iso_s_desc},
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, rtd1625_iso_match);
+
+static struct platform_driver rtd1625_iso_driver = {
+ .probe = rtd1625_iso_probe,
+ .driver = {
+ .name = "rtk-rtd1625-iso-clk",
+ .of_match_table = rtd1625_iso_match,
+ .suppress_bind_attrs = true,
+ },
+};
+
+static int __init rtd1625_iso_init(void)
+{
+ return platform_driver_register(&rtd1625_iso_driver);
+}
+subsys_initcall(rtd1625_iso_init);
+
+MODULE_DESCRIPTION("Realtek RTD1625 ISO Clock Controller Driver");
+MODULE_AUTHOR("Cheng-Yu Lee <cylee12@realtek.com>");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS("REALTEK_CLK");
diff --git a/drivers/reset/realtek/Makefile b/drivers/reset/realtek/Makefile
index 65c29a12524d..e46a3831b582 100644
--- a/drivers/reset/realtek/Makefile
+++ b/drivers/reset/realtek/Makefile
@@ -1,3 +1,3 @@
# SPDX-License-Identifier: GPL-2.0-only
obj-$(CONFIG_RESET_RTK_COMMON) += common.o
-obj-$(CONFIG_RESET_RTD1625) += reset-rtd1625-crt.o
+obj-$(CONFIG_RESET_RTD1625) += reset-rtd1625-crt.o reset-rtd1625-iso.o
diff --git a/drivers/reset/realtek/reset-rtd1625-iso.c b/drivers/reset/realtek/reset-rtd1625-iso.c
new file mode 100644
index 000000000000..08a5d1e36fbc
--- /dev/null
+++ b/drivers/reset/realtek/reset-rtd1625-iso.c
@@ -0,0 +1,99 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2026 Realtek Semiconductor Corporation
+ */
+
+#include <dt-bindings/reset/realtek,rtd1625.h>
+#include <linux/auxiliary_bus.h>
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <linux/of.h>
+#include <linux/slab.h>
+#include "common.h"
+
+#define RTD1625_ISO_RSTN_MAX 29
+#define RTD1625_ISO_S_RSTN_MAX 5
+
+static const struct rtk_reset_desc rtd1625_iso_reset_descs[] = {
+ [RTD1625_ISO_RSTN_VFD] = { .ofs = 0x88, .bit = 0 },
+ [RTD1625_ISO_RSTN_CEC0] = { .ofs = 0x88, .bit = 2 },
+ [RTD1625_ISO_RSTN_CEC1] = { .ofs = 0x88, .bit = 3 },
+ [RTD1625_ISO_RSTN_CBUSTX] = { .ofs = 0x88, .bit = 5 },
+ [RTD1625_ISO_RSTN_CBUSRX] = { .ofs = 0x88, .bit = 6 },
+ [RTD1625_ISO_RSTN_USB3_PHY2_XTAL_POW] = { .ofs = 0x88, .bit = 7 },
+ [RTD1625_ISO_RSTN_UR0] = { .ofs = 0x88, .bit = 8 },
+ [RTD1625_ISO_RSTN_GMAC] = { .ofs = 0x88, .bit = 9 },
+ [RTD1625_ISO_RSTN_GPHY] = { .ofs = 0x88, .bit = 10 },
+ [RTD1625_ISO_RSTN_I2C_0] = { .ofs = 0x88, .bit = 11 },
+ [RTD1625_ISO_RSTN_I2C_1] = { .ofs = 0x88, .bit = 12 },
+ [RTD1625_ISO_RSTN_CBUS] = { .ofs = 0x88, .bit = 13 },
+ [RTD1625_ISO_RSTN_USB_DRD] = { .ofs = 0x88, .bit = 14 },
+ [RTD1625_ISO_RSTN_USB_HOST] = { .ofs = 0x88, .bit = 15 },
+ [RTD1625_ISO_RSTN_USB_PHY_0] = { .ofs = 0x88, .bit = 16 },
+ [RTD1625_ISO_RSTN_USB_PHY_1] = { .ofs = 0x88, .bit = 17 },
+ [RTD1625_ISO_RSTN_USB_PHY_2] = { .ofs = 0x88, .bit = 18 },
+ [RTD1625_ISO_RSTN_USB] = { .ofs = 0x88, .bit = 19 },
+ [RTD1625_ISO_RSTN_TYPE_C] = { .ofs = 0x88, .bit = 20 },
+ [RTD1625_ISO_RSTN_USB_U3_HOST] = { .ofs = 0x88, .bit = 21 },
+ [RTD1625_ISO_RSTN_USB3_PHY0_POW] = { .ofs = 0x88, .bit = 22 },
+ [RTD1625_ISO_RSTN_USB3_P0_MDIO] = { .ofs = 0x88, .bit = 23 },
+ [RTD1625_ISO_RSTN_USB3_PHY1_POW] = { .ofs = 0x88, .bit = 24 },
+ [RTD1625_ISO_RSTN_USB3_P1_MDIO] = { .ofs = 0x88, .bit = 25 },
+ [RTD1625_ISO_RSTN_VTC] = { .ofs = 0x88, .bit = 26 },
+ [RTD1625_ISO_RSTN_USB3_PHY2_POW] = { .ofs = 0x88, .bit = 27 },
+ [RTD1625_ISO_RSTN_USB3_P2_MDIO] = { .ofs = 0x88, .bit = 28 },
+ [RTD1625_ISO_RSTN_USB_PHY_3] = { .ofs = 0x88, .bit = 29 },
+ [RTD1625_ISO_RSTN_USB_PHY_4] = { .ofs = 0x88, .bit = 30 },
+};
+
+static const struct rtk_reset_desc rtd1625_iso_s_reset_descs[] = {
+ [RTD1625_ISO_S_RSTN_ISOM_MIS] = { .ofs = 0x310, .bit = 0, .write_en = 1 },
+ [RTD1625_ISO_S_RSTN_GPIOM] = { .ofs = 0x310, .bit = 2, .write_en = 1 },
+ [RTD1625_ISO_S_RSTN_TIMER7] = { .ofs = 0x310, .bit = 4, .write_en = 1 },
+ [RTD1625_ISO_S_RSTN_IRDA] = { .ofs = 0x310, .bit = 6, .write_en = 1 },
+ [RTD1625_ISO_S_RSTN_UR10] = { .ofs = 0x310, .bit = 8, .write_en = 1 },
+};
+
+static int rtd1625_iso_reset_probe(struct auxiliary_device *adev,
+ const struct auxiliary_device_id *id)
+{
+ struct device *dev = &adev->dev;
+ struct device *parent = dev->parent;
+ struct rtk_reset_data *data;
+
+ data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ if (of_device_is_compatible(parent->of_node, "realtek,rtd1625-iso-s-clk")) {
+ data->descs = rtd1625_iso_s_reset_descs;
+ data->rcdev.nr_resets = RTD1625_ISO_S_RSTN_MAX;
+ } else {
+ data->descs = rtd1625_iso_reset_descs;
+ data->rcdev.nr_resets = RTD1625_ISO_RSTN_MAX;
+ }
+
+ data->rcdev.owner = THIS_MODULE;
+
+ return rtk_reset_controller_add(dev, data);
+}
+
+static const struct auxiliary_device_id rtd1625_iso_reset_ids[] = {
+ { .name = "clk_rtk.iso_rst" },
+ { .name = "clk_rtk.iso_s_rst" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(auxiliary, rtd1625_iso_reset_ids);
+
+static struct auxiliary_driver rtd1625_iso_driver = {
+ .probe = rtd1625_iso_reset_probe,
+ .id_table = rtd1625_iso_reset_ids,
+ .driver = {
+ .name = "rtd1625-iso-reset",
+ },
+};
+module_auxiliary_driver(rtd1625_iso_driver);
+
+MODULE_DESCRIPTION("Realtek RTD1625 ISO Reset Controller Driver");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS("REALTEK_RESET");
--
2.43.0
^ permalink raw reply related
* Re: [PATCH v2] gpiolib: handle gpio-hogs only once
From: Bartosz Golaszewski @ 2026-06-10 8:12 UTC (permalink / raw)
To: Daniel Drake; +Cc: linux-gpio, linux-arm-kernel, linusw, Bartosz Golaszewski
In-Reply-To: <b07f5bd8-26f8-4de4-becb-4f76f9d33361@reactivated.net>
On Tue, 9 Jun 2026 22:48:03 +0200, Daniel Drake <dan@reactivated.net> said:
> On 09/06/2026 13:39, Bartosz Golaszewski wrote:
>> On Mon, 8 Jun 2026 23:01:08 +0200, Daniel Drake <dan@reactivated.net> said:
>>> diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
>>> index 1e6dce430dca..b02d711289d0 100644
>>> --- a/drivers/gpio/gpiolib.c
>>> +++ b/drivers/gpio/gpiolib.c
>>> @@ -1031,9 +1031,17 @@ static int gpiochip_hog_lines(struct gpio_chip *gc)
>>> if (!fwnode_property_present(fwnode, "gpio-hog"))
>>> continue;
>>>
>>> + /* The hog may have been handled by another gpio_chip on the same fwnode */
>>> + if (is_of_node(fwnode) &&
>>> + of_node_check_flag(to_of_node(fwnode), OF_POPULATED))
>>> + continue;
>>> +
>>> ret = gpiochip_add_hog(gc, fwnode);
>>> if (ret)
>>> return ret;
>>> +
>>> + if (is_of_node(fwnode))
>>> + of_node_set_flag(to_of_node(fwnode), OF_POPULATED);
>>
>> Sashiko correctly points out that on errors, the state will be corrupted. We
>> could maybe move the clearing of the flag to gpiochip_free_hogs() and track its
>> state when processing fwnodes in order not to clear it incorrectly?
>
> I guess you are referring to:
>
>> Does setting OF_POPULATED here cause state corruption if a secondary chip on a
>> shared node fails to probe?
>> When multiple gpio_chip instances share a device node, the first chip processes
>> its hogs and sets OF_POPULATED. If a subsequent chip fails probe (for example,
>> returning -EPROBE_DEFER), its cleanup path calls of_gpiochip_remove() which
>> clears the flag for all hogs.
>> If the flag is unconditionally cleared, will the deferred chip attempt to
>> process the first chip's hogs on retry, fail due to a mismatch, and
>> permanently abort probe?
>
>
> I don't think this is actually an issue. If we have two gpio_chips
> sharing a device node, a first one with a hog that probes fine and a
> subsequent one that fails during probe, both of the gpio_chips will
> brought down and the flag is cleared. If it was a EPROBE_DEFER case
> which is then retried later, the first chip's hogs will be set up a 2nd
> time when the probe is retried.
>
> It is true that the teardown of the 2nd gpio_chip would erase the
> OF_POPULATED flag of a gpio-hog node that it does not "own", but the
> first gpio_chip would also be torn down at the same time (and
> OF_POPULATED unset a 2nd time). This is not ideal, but harmless as far
> as I can see.
>
> I don't quite follow the suggestion for doing the clearing better in
> gpiochip_free_hogs(). It would be neat if we could go from a hogged
> gpio_desc back to the fwnode, so that we could only unset OF_POPULATED
> on the fwnode at the point when we are really removing the hog, but I
> don't see a way to derive the gpio-hog fwnode from gpio_desc. Also, this
> would be complicated because one gpio-hog node can hog multiple gpios.
>
> Let me know if I'm missing anything or if you have any preference to
> handle this differently!
>
> Thanks
> Daniel
>
>
Ok, thanks for the clarification. Let's give this a chance then.
Bart
^ permalink raw reply
* Re: [PATCH v2] gpiolib: handle gpio-hogs only once
From: Bartosz Golaszewski @ 2026-06-10 8:13 UTC (permalink / raw)
To: linusw, brgl, Daniel Drake
Cc: Bartosz Golaszewski, linux-gpio, linux-arm-kernel
In-Reply-To: <20260608210108.36248-1-dan@reactivated.net>
On Mon, 08 Jun 2026 22:01:08 +0100, Daniel Drake wrote:
> Commit d1d564ec49929 ("gpio: move hogs into GPIO core") introduced a
> behaviour change that breaks boot on Raspberry Pi 5 when using the
> firmware-supplied device tree:
>
> gpiochip_add_data_with_key: GPIOs 544..575
> (/soc@107c000000/gpio@7d517c00) failed to register, -22
> brcmstb-gpio 107d517c00.gpio: Could not add gpiochip for bank 1
> brcmstb-gpio 107d517c00.gpio: probe with driver brcmstb-gpio failed
> with error -22
>
> [...]
Applied, thanks!
[1/1] gpiolib: handle gpio-hogs only once
https://git.kernel.org/brgl/c/a23226b7c1f69eafd9ced4e037fb51c9758c0501
Best regards,
--
Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
^ permalink raw reply
* [PATCH 0/2] Cleanup and fix for NanoPC-T6 Plus
From: Diederik de Haas @ 2026-06-10 8:04 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
Cc: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel,
Jonas Karlman, Marcin Juszkiewicz, Diederik de Haas
Several nodes were enabled/configured when support for the NanoPC-T6 Plus was
added, but later those same nodes got enabled/configured in the dtsi file,
making those in the dts file superfluous, so remove them.
The MTT USB 2.0 Hub is connected to USB20 HOST1, so the phy-supply belongs to
u2phy3_host, not u2phy2_host as that is for USB20 HOST0.
Diederik de Haas (2):
arm64: dts: rockchip: Drop duplicate USB nodes on NanoPC-T6 LTS
arm64: dts: rockchip: Fix USB hub phy-supply config for NanoPC-T6 LTS
.../dts/rockchip/rk3588-nanopc-t6-lts.dts | 19 +------------------
1 file changed, 1 insertion(+), 18 deletions(-)
--
2.53.0
^ permalink raw reply
* [PATCH 1/2] arm64: dts: rockchip: Drop duplicate USB nodes on NanoPC-T6 LTS
From: Diederik de Haas @ 2026-06-10 8:04 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
Cc: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel,
Jonas Karlman, Marcin Juszkiewicz, Diederik de Haas
In-Reply-To: <20260610081400.758687-1-diederik@cknow-tech.com>
Several USB nodes were enabled/configured on the NanoPC-T6 LTS first. Then
those same nodes were enabled/configured in the NanoPC-T6 dtsi file, but
the ones in the LTS dts file were not removed, so do so now.
Signed-off-by: Diederik de Haas <diederik@cknow-tech.com>
---
.../boot/dts/rockchip/rk3588-nanopc-t6-lts.dts | 17 -----------------
1 file changed, 17 deletions(-)
diff --git a/arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6-lts.dts b/arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6-lts.dts
index ff855064be08..0ee67ee24f3c 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6-lts.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6-lts.dts
@@ -38,23 +38,6 @@ usb20_host_pwren: usb20-host-pwren {
};
};
-&u2phy1 {
- status = "okay";
-};
-
-&u2phy1_otg {
- status = "okay";
-};
-
&u2phy2_host {
phy-supply = <&vcc5v0_usb20_host>;
};
-
-&usbdp_phy1 {
- status = "okay";
-};
-
-&usb_host1_xhci {
- dr_mode = "host";
- status = "okay";
-};
--
2.53.0
^ permalink raw reply related
* [PATCH 2/2] arm64: dts: rockchip: Fix USB hub phy-supply config for NanoPC-T6 LTS
From: Diederik de Haas @ 2026-06-10 8:04 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
Cc: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel,
Jonas Karlman, Marcin Juszkiewicz, Diederik de Haas, stable
In-Reply-To: <20260610081400.758687-1-diederik@cknow-tech.com>
The MTT USB 2.0 hub is connected to the SoC's USB20 HOST1, so the phy-supply
belongs to u2phy3_host, not u2phy2_host as that is for USB20 HOST0.
Fixes: db1dcbe5f752 ("arm64: dts: rockchip: add NanoPC-T6 LTS")
Cc: stable@vger.kernel.org
Signed-off-by: Diederik de Haas <diederik@cknow-tech.com>
---
arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6-lts.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6-lts.dts b/arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6-lts.dts
index 0ee67ee24f3c..0e15a2e1f2ff 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6-lts.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6-lts.dts
@@ -38,6 +38,6 @@ usb20_host_pwren: usb20-host-pwren {
};
};
-&u2phy2_host {
+&u2phy3_host {
phy-supply = <&vcc5v0_usb20_host>;
};
--
2.53.0
^ permalink raw reply related
* [PATCH v3 0/2] clk: amlogic: Add A9 peripherals clock controller
From: Jian Hu via B4 Relay @ 2026-06-10 8:14 UTC (permalink / raw)
To: Neil Armstrong, Jerome Brunet, Michael Turquette, Stephen Boyd,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Xianwei Zhao,
Kevin Hilman, Martin Blumenstingl
Cc: linux-amlogic, linux-clk, devicetree, linux-kernel,
linux-arm-kernel, Jian Hu, Conor Dooley
This series adds Amlogic A9 peripherals clock support,
including dt-binding and peripherals clock driver.
Note that this driver depends on the A9 PLL driver, which is not yet
upstream. The Meson PLL framework is currently undergoing refactoring,
and the A9 PLL driver will be submitted as a follow-up series after
that work has been completed.
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
---
Changes in v3:
- Add "depend on A9 pll" instructions in the cover-letter.
- Move COMPILE_TEST after 'depends on ARM64' reported by sashiko-bot.
- Fix usb_48m_pre_sel's parent reported by sashiko-bot.
- Fix gen_div width reported by sashiko-bot.
- Fix hdmitx1_pixel's parent reported by sashiko-bot.
- Link to v2: https://lore.kernel.org/r/20260603-a9_peripherals-v2-0-ee1b8c0a1e6c@amlogic.com
Changes in v2:
- Split the A9 clock driver and send the peripherals clock separately.
- Add COMPILE_TEST in Kconfig.
- Drop the 'optional'.
- Rename apb4 to soc.
- Sort the header file.
- Rename hifi to hifi0.
- Use CLK_HW_INIT_PARENTS_DATA to describe clk_init_data.
- Use CLK_HW_INIT_HW to describe clk_init_data.
- Use CLK_HW_INIT_PARENTS_HW to describe clk_init_data.
- Link to v1: https://lore.kernel.org/all/20260511-b4-a9_clk-v1-0-41cb4071b7c9@amlogic.com/
---
Jian Hu (2):
dt-bindings: clock: Add Amlogic A9 peripherals clock controller
clk: amlogic: Add A9 peripherals clock controller driver
.../clock/amlogic,a9-peripherals-clkc.yaml | 160 ++
drivers/clk/meson/Kconfig | 15 +
drivers/clk/meson/Makefile | 1 +
drivers/clk/meson/a9-peripherals.c | 1925 ++++++++++++++++++++
.../clock/amlogic,a9-peripherals-clkc.h | 352 ++++
5 files changed, 2453 insertions(+)
---
base-commit: ca89c88bcf69daca829044c638a8163d5ce47af0
change-id: 20260603-a9_peripherals-4214e79705dc
Best regards,
--
Jian Hu <jian.hu@amlogic.com>
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox