[PATCH V3 3/4] arm64: dts: qcom: hamoa: Add UFS nodes for x1e80100 SoC

[Pradeep P V K <pradeep.pragallapati@oss.qualcomm.com>]

Add UFS host controller and PHY nodes for x1e80100 SoC.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Taniya Das <taniya.das@oss.qualcomm.com>
Signed-off-by: Pradeep P V K <pradeep.pragallapati@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/hamoa.dtsi | 123 +++++++++++++++++++++++++++-
 1 file changed, 120 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/hamoa.dtsi b/arch/arm64/boot/dts/qcom/hamoa.dtsi
index f7d71793bc77..33899fa06aa4 100644
--- a/arch/arm64/boot/dts/qcom/hamoa.dtsi
+++ b/arch/arm64/boot/dts/qcom/hamoa.dtsi
@@ -835,9 +835,9 @@ gcc: clock-controller@100000 {
 				 <0>,
 				 <0>,
 				 <0>,
-				 <0>,
-				 <0>,
-				 <0>;
+				 <&ufs_mem_phy 0>,
+				 <&ufs_mem_phy 1>,
+				 <&ufs_mem_phy 2>;
 
 			power-domains = <&rpmhpd RPMHPD_CX>;
 			#clock-cells = <1>;
@@ -3848,6 +3848,123 @@ pcie4_phy: phy@1c0e000 {
 			status = "disabled";
 		};
 
+		ufs_mem_phy: phy@1d80000 {
+			compatible = "qcom,x1e80100-qmp-ufs-phy",
+				     "qcom,sm8550-qmp-ufs-phy";
+			reg = <0x0 0x01d80000 0x0 0x2000>;
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>,
+				 <&tcsr TCSR_UFS_PHY_CLKREF_EN>;
+
+			clock-names = "ref",
+				      "ref_aux",
+				      "qref";
+			resets = <&ufs_mem_hc 0>;
+			reset-names = "ufsphy";
+
+			power-domains = <&gcc GCC_UFS_MEM_PHY_GDSC>;
+
+			#clock-cells = <1>;
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		ufs_mem_hc: ufs@1d84000 {
+			compatible = "qcom,x1e80100-ufshc",
+				     "qcom,sm8550-ufshc",
+				     "qcom,ufshc",
+				     "jedec,ufs-2.0";
+			reg = <0x0 0x01d84000 0x0 0x3000>;
+
+			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_UFS_PHY_AXI_CLK>,
+				 <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+				 <&gcc GCC_UFS_PHY_AHB_CLK>,
+				 <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
+				 <&rpmhcc RPMH_LN_BB_CLK3>,
+				 <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+				 <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+				 <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
+			clock-names = "core_clk",
+				      "bus_aggr_clk",
+				      "iface_clk",
+				      "core_clk_unipro",
+				      "ref_clk",
+				      "tx_lane0_sync_clk",
+				      "rx_lane0_sync_clk",
+				      "rx_lane1_sync_clk";
+
+			operating-points-v2 = <&ufs_opp_table>;
+
+			resets = <&gcc GCC_UFS_PHY_BCR>;
+			reset-names = "rst";
+
+			interconnects = <&aggre1_noc MASTER_UFS_MEM QCOM_ICC_TAG_ALWAYS
+					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+					<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY
+					 &config_noc SLAVE_UFS_MEM_CFG QCOM_ICC_TAG_ACTIVE_ONLY>;
+			interconnect-names = "ufs-ddr",
+					     "cpu-ufs";
+
+			power-domains = <&gcc GCC_UFS_PHY_GDSC>;
+			required-opps = <&rpmhpd_opp_nom>;
+
+			iommus = <&apps_smmu 0x1a0 0>;
+			dma-coherent;
+
+			lanes-per-direction = <2>;
+
+			phys = <&ufs_mem_phy>;
+			phy-names = "ufsphy";
+
+			#reset-cells = <1>;
+
+			status = "disabled";
+
+			ufs_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-75000000 {
+					opp-hz = /bits/ 64 <75000000>,
+						 /bits/ 64 <0>,
+						 /bits/ 64 <0>,
+						 /bits/ 64 <75000000>,
+						 /bits/ 64 <0>,
+						 /bits/ 64 <0>,
+						 /bits/ 64 <0>,
+						 /bits/ 64 <0>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+				};
+
+				opp-150000000 {
+					opp-hz = /bits/ 64 <150000000>,
+						 /bits/ 64 <0>,
+						 /bits/ 64 <0>,
+						 /bits/ 64 <150000000>,
+						 /bits/ 64 <0>,
+						 /bits/ 64 <0>,
+						 /bits/ 64 <0>,
+						 /bits/ 64 <0>;
+					required-opps = <&rpmhpd_opp_svs>;
+				};
+
+				opp-300000000 {
+					opp-hz = /bits/ 64 <300000000>,
+						 /bits/ 64 <0>,
+						 /bits/ 64 <0>,
+						 /bits/ 64 <300000000>,
+						 /bits/ 64 <0>,
+						 /bits/ 64 <0>,
+						 /bits/ 64 <0>,
+						 /bits/ 64 <0>;
+					required-opps = <&rpmhpd_opp_nom>;
+				};
+			};
+		};
+
 		cryptobam: dma-controller@1dc4000 {
 			compatible = "qcom,bam-v1.7.4", "qcom,bam-v1.7.0";
 			reg = <0x0 0x01dc4000 0x0 0x28000>;
-- 
2.34.1