[PATCH v13 00/29] Add i2c-mux and eeprom devices for Meta Yosemite 4

[PATCH v13 00/29] Add i2c-mux and eeprom devices for Meta Yosemite 4

[Delphine CC Chiu]

Changelog:
  - v13
    - Add RTQ6056-support-on-bus-11 
  - v12
    - Fix GPIO linename typo and add missing GPIO pin initial state.
  - v11
    - Revise all GPIO line name with bottom line
  - v10
    - adjust mgm cpld ioexp bus
    - add GPIOO7 name
    - remove mctp driver
  - v9
    - add XDP710 support
    - add RTQ6056 support
    - add MP5990 support
  - v8
    - add fan led config
  - v7
    - Revise pca9506 i2c address
  - v6
    - Revise i2c duty-cycle for meeting 400khz spec
  - v5
    - Support medusa board adc sensors
    - support NIC eeprom
  - v4
    - Re-format gpio linename
    - Revise i2c device node names
    - Split patches by logic changes
  - v3
    - Correct patch for revising gpio name
  - v2
    - Revise mx31790 fan tach config
    - Add mctp config for NIC
    - Support mux to cpld
    - Revise gpio name
  - v1
    - Add gpio and eeprom behind i2c-mux
    - Remove redundant idle-state setting for i2c-mux
    - Enable adc 15, wdt2,spi gpio for yosemite4 use
    - Revise quad mode to dual mode to avoid WP pin influnece the SPI
    - Revise power sensor adm1281 for yosemite4 schematic change
    - Add gpio pca9506 I/O expander for yosemite4 use
    - remove space for adm1272 compatible
    - enable interrupt setting for pca9555
    - add eeprom for yosemite4 medusa board/BSM use
    - remove temperature sensor for yosemite4 schematic change
    - add power sensor for power module reading
    - Revise adc128d818 adc mode for yosemite4 schematic change
    - Revise ina233 for yosemite4 schematic change
    - Remove idle state setting for yosemite4 NIC connection
    - Initialize bmc gpio state
    - Revise mx31790 fan tach config
    - Add mctp config for NIC
    - Support mux to cpld
    - Revise gpio name

Delphine CC Chiu (28):
  ARM: dts: aspeed: yosemite4: Revise i2c-mux devices
  ARM: dts: aspeed: yosemite4: Enable adc15
  ARM: dts: aspeed: yosemite4: Enable spi-gpio setting
  ARM: dts: aspeed: yosemite4: Enable watchdog2
  ARM: dts: aspeed: yosemite4: Revise quad mode to dual mode
  ARM: dts: aspeed: yosemite4: Revise power sensor adm1281 for schematic
    change
  ARM: dts: aspeed: yosemite4: Add gpio pca9506
  ARM: dts: aspeed: yosemite4: Remove space for adm1272 compatible
  ARM: dts: aspeed: yosemite4: Enable interrupt setting for pca9555
  ARM: dts: aspeed: yosemite4: Add power sensor for power module reading
  ARM: dts: aspeed: yosemite4: Add eeprom for yosemite4 use
  ARM: dts: aspeed: yosemite4: Remove temperature sensor for yosemite4
    schematic change
  ARM: dts: aspeed: yosemite4: Revise adc128d818 adc mode for yosemite4
    schematic change
  ARM: dts: aspeed: yosemite4: Revise ina233 config for yosemite4
    schematic change
  ARM: dts: aspeed: yosemite4: Remove idle state setting for yosemite4
    NIC connection
  ARM: dts: aspeed: yosemite4: Initialize bmc gpio state
  ARM: dts: aspeed: yosemite4: Revise mx31790 fan tach config
  ARM: dts: aspeed: yosemite4: add mctp config for NIC
  ARM: dts: aspeed: yosemite4: support mux to cpld
  ARM: dts: aspeed: yosemite4: support medusa board adc sensors
  ARM: dts: aspeed: yosemite4: support NIC eeprom
  ARM: dts: aspeed: yosemite4: Revise i2c duty-cycle
  ARM: dts: aspeed: yosemite4: add fan led config
  ARM: dts: aspeed: yosemite4: add XDP710
  ARM: dts: aspeed: yosemite4: add RTQ6056 support
  ARM: dts: aspeed: yosemite4: add MP5990 support
  ARM: dts: aspeed: yosemite4: Adjust ioexp bus and remove mctp driver
  ARM: dts: aspeed: yosemite4: fix GPIO linename typo

Ian-I-Chien (1):
  ARM: dts: aspeed: yosemitet4: add RTQ6056 support on 11 (0x41).

 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 1749 ++++++++++++++++-
 1 file changed, 1653 insertions(+), 96 deletions(-)

-- 
2.25.1

[PATCH v13 01/29] ARM: dts: aspeed: yosemite4: Revise i2c-mux devices

[Delphine CC Chiu]

Revise Yosemite 4 devicetree for devices behind i2c-mux
- Add gpio and eeprom behind i2c-mux
- Remove redundant idle-state setting for i2c-mux

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 381 ++++++++++++++++--
 1 file changed, 347 insertions(+), 34 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 98477792aa00..ce206e2c461b 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -17,6 +17,25 @@ aliases {
 		serial6 = &uart7;
 		serial7 = &uart8;
 		serial8 = &uart9;
+
+		i2c16 = &imux16;
+		i2c17 = &imux17;
+		i2c18 = &imux18;
+		i2c19 = &imux19;
+		i2c20 = &imux20;
+		i2c21 = &imux21;
+		i2c22 = &imux22;
+		i2c23 = &imux23;
+		i2c24 = &imux24;
+		i2c25 = &imux25;
+		i2c26 = &imux26;
+		i2c27 = &imux27;
+		i2c28 = &imux28;
+		i2c29 = &imux29;
+		i2c30 = &imux30;
+		i2c31 = &imux31;
+		i2c32 = &imux32;
+		i2c33 = &imux33;
 	};
 
 	chosen {
@@ -259,9 +278,109 @@ &i2c8 {
 	bus-frequency = <400000>;
 	i2c-mux at 70 {
 		compatible = "nxp,pca9544";
-		idle-state = <0>;
 		i2c-mux-idle-disconnect;
 		reg = <0x70>;
+
+		imux16: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			gpio at 49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom at 51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom at 54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+
+		imux17: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			gpio at 49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom at 51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom at 54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+
+		imux18: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			gpio at 49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom at 51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom at 54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+
+		imux19: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			gpio at 49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom at 51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom at 54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
 	};
 };
 
@@ -270,15 +389,174 @@ &i2c9 {
 	bus-frequency = <400000>;
 	i2c-mux at 71 {
 		compatible = "nxp,pca9544";
-		idle-state = <0>;
 		i2c-mux-idle-disconnect;
 		reg = <0x71>;
+
+		imux20: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			gpio at 49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom at 51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom at 54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+
+		imux21: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			gpio at 49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom at 51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom at 54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+
+		imux22: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			gpio at 49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom at 51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom at 54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+
+		imux23: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			gpio at 49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom at 51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom at 54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
 	};
 };
 
 &i2c10 {
 	status = "okay";
 	bus-frequency = <400000>;
+	i2c-mux at 74 {
+		compatible = "nxp,pca9544";
+		i2c-mux-idle-disconnect;
+		reg = <0x74>;
+
+		imux28: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			gpio at 20 {
+				compatible = "nxp,pca9506";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio at 21 {
+				compatible = "nxp,pca9506";
+				reg = <0x21>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio at 22 {
+				compatible = "nxp,pca9506";
+				reg = <0x22>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio at 23 {
+				compatible = "nxp,pca9506";
+				reg = <0x23>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio at 24 {
+				compatible = "nxp,pca9506";
+				reg = <0x24>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-line-names =
+				"","","","",
+				"NIC0_MAIN_PWR_EN","NIC1_MAIN_PWR_EN",
+				"NIC2_MAIN_PWR_EN","NIC3_MAIN_PWR_EN",
+				"","","","","","","","",
+				"","","","","","","","",
+				"","","","","","","","";
+			};
+		};
+
+		imux29: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+	};
 };
 
 &i2c11 {
@@ -440,16 +718,14 @@ eeprom at 51 {
 		reg = <0x51>;
 	};
 
-	i2c-mux at 71 {
-		compatible = "nxp,pca9846";
+	i2c-mux at 74 {
+		compatible = "nxp,pca9546";
 		#address-cells = <1>;
 		#size-cells = <0>;
-
-		idle-state = <0>;
 		i2c-mux-idle-disconnect;
-		reg = <0x71>;
+		reg = <0x74>;
 
-		i2c at 0 {
+		imux30: i2c at 0 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0>;
@@ -457,26 +733,26 @@ i2c at 0 {
 			adc at 1f {
 				compatible = "ti,adc128d818";
 				reg = <0x1f>;
-				ti,mode = /bits/ 8 <2>;
+				ti,mode = /bits/ 8 <1>;
 			};
 
 			pwm at 20{
-				compatible = "max31790";
+				compatible = "maxim,max31790";
+				pwm-as-tach = <4 5>;
 				reg = <0x20>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 			};
 
 			gpio at 22{
 				compatible = "ti,tca6424";
 				reg = <0x22>;
+				gpio-controller;
+				#gpio-cells = <2>;
 			};
 
-			pwm at 23{
-				compatible = "max31790";
-				reg = <0x23>;
-				#address-cells = <1>;
-				#size-cells = <0>;
+			pwm at 2f{
+				compatible = "maxim,max31790";
+				pwm-as-tach = <4 5>;
+				reg = <0x2f>;
 			};
 
 			adc at 33 {
@@ -499,34 +775,34 @@ gpio at 61 {
 			};
 		};
 
-		i2c at 1 {
+		imux31: i2c at 1 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			reg = <0>;
+			reg = <1>;
 
 			adc at 1f {
 				compatible = "ti,adc128d818";
 				reg = <0x1f>;
-				ti,mode = /bits/ 8 <2>;
+				ti,mode = /bits/ 8 <1>;
 			};
 
 			pwm at 20{
-				compatible = "max31790";
+				compatible = "maxim,max31790";
+				pwm-as-tach = <4 5>;
 				reg = <0x20>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 			};
 
 			gpio at 22{
 				compatible = "ti,tca6424";
 				reg = <0x22>;
+				gpio-controller;
+				#gpio-cells = <2>;
 			};
 
-			pwm at 23{
-				compatible = "max31790";
-				reg = <0x23>;
-				#address-cells = <1>;
-				#size-cells = <0>;
+			pwm at 2f{
+				compatible = "maxim,max31790";
+				pwm-as-tach = <4 5>;
+				reg = <0x2f>;
 			};
 
 			adc at 33 {
@@ -554,12 +830,10 @@ i2c-mux at 73 {
 		compatible = "nxp,pca9544";
 		#address-cells = <1>;
 		#size-cells = <0>;
-
-		idle-state = <0>;
 		i2c-mux-idle-disconnect;
 		reg = <0x73>;
 
-		i2c at 0 {
+		imux32: i2c at 0 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0>;
@@ -570,10 +844,10 @@ adc at 35 {
 			};
 		};
 
-		i2c at 1 {
+		imux33: i2c at 1 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			reg = <0>;
+			reg = <1>;
 
 			adc at 35 {
 				compatible = "maxim,max11617";
@@ -596,9 +870,48 @@ mctp at 10 {
 
 	i2c-mux at 72 {
 		compatible = "nxp,pca9544";
-		idle-state = <0>;
 		i2c-mux-idle-disconnect;
 		reg = <0x72>;
+
+		imux24: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			temperature-sensor at 1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
+
+		imux25: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			temperature-sensor at 1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
+
+		imux26: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			temperature-sensor at 1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
+
+		imux27: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			temperature-sensor at 1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
 	};
 };
 
-- 
2.25.1

[PATCH v13 02/29] ARM: dts: aspeed: yosemite4: Enable adc15

[Delphine CC Chiu]

Enable Yosemite 4 adc15 config

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index ce206e2c461b..0d659ee2bc19 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -51,7 +51,7 @@ iio-hwmon {
 		compatible = "iio-hwmon";
 		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
 				<&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
-				<&adc1 0>, <&adc1 1>;
+				<&adc1 0>, <&adc1 1>, <&adc1 7>;
 	};
 };
 
@@ -925,10 +925,10 @@ &pinctrl_adc4_default &pinctrl_adc5_default
 
 &adc1 {
 	status = "okay";
-	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default>;
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default>
+			&pinctrl_adc15_default>;
 };
 
-
 &ehci0 {
 	status = "okay";
 };
-- 
2.25.1

[PATCH v13 03/29] ARM: dts: aspeed: yosemite4: Enable spi-gpio setting

[Delphine CC Chiu]

enable spi-gpio setting for spi flash

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts   | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 0d659ee2bc19..575abdd530df 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -53,6 +53,24 @@ iio-hwmon {
 				<&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
 				<&adc1 0>, <&adc1 1>, <&adc1 7>;
 	};
+
+	spi_gpio: spi-gpio {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-sck = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_HIGH>;
+		gpio-mosi = <&gpio0 ASPEED_GPIO(X, 4) GPIO_ACTIVE_HIGH>;
+		gpio-miso = <&gpio0 ASPEED_GPIO(X, 5) GPIO_ACTIVE_HIGH>;
+		num-chipselects = <1>;
+		cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>;
+
+		tpmdev at 0 {
+			compatible = "tcg,tpm_tis-spi";
+			spi-max-frequency = <33000000>;
+			reg = <0>;
+		};
+	};
 };
 
 &uart1 {
-- 
2.25.1

[PATCH v13 04/29] ARM: dts: aspeed: yosemite4: Enable watchdog2

[Delphine CC Chiu]

enable watchdog2 setting

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 575abdd530df..51b4e9ae13cc 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -120,6 +120,13 @@ &wdt1 {
 	aspeed,ext-pulse-duration = <256>;
 };
 
+&wdt2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst2_default>;
+	aspeed,reset-type = "system";
+};
+
 &mac2 {
 	status = "okay";
 	pinctrl-names = "default";
-- 
2.25.1

[PATCH v13 05/29] ARM: dts: aspeed: yosemite4: Revise quad mode to dual mode

[Delphine CC Chiu]

Revise quad mode to dual mode to avoid WP pin influnece the SPI

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 51b4e9ae13cc..e5354efbb903 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -149,15 +149,17 @@ flash at 0 {
 		status = "okay";
 		m25p,fast-read;
 		label = "bmc";
-		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <2>;
+		spi-rx-bus-width = <2>;
 		spi-max-frequency = <50000000>;
-#include "openbmc-flash-layout-64.dtsi"
+#include "openbmc-flash-layout-128.dtsi"
 	};
 	flash at 1 {
 		status = "okay";
 		m25p,fast-read;
 		label = "bmc2";
-		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <2>;
+		spi-rx-bus-width = <2>;
 		spi-max-frequency = <50000000>;
 	};
 };
-- 
2.25.1

[PATCH v13 06/29] ARM: dts: aspeed: yosemite4: Revise power sensor adm1281 for schematic change

[Delphine CC Chiu]

Revise power sensor adm1281 for yosemite4 schematic change

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 24 ++++++++++++-------
 1 file changed, 16 insertions(+), 8 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index e5354efbb903..7b79fcd77c8c 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -176,8 +176,9 @@ mctp at 10 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1278";
+		compatible = "adi,adm1281";
 		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
 	};
 };
 
@@ -193,8 +194,9 @@ mctp at 10 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1278";
+		compatible = "adi,adm1281";
 		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
 	};
 };
 
@@ -210,8 +212,9 @@ mctp at 10 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1278";
+		compatible = "adi,adm1281";
 		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
 	};
 };
 
@@ -227,8 +230,9 @@ mctp at 10 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1278";
+		compatible = "adi,adm1281";
 		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
 	};
 };
 
@@ -244,8 +248,9 @@ mctp at 10 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1278";
+		compatible = "adi,adm1281";
 		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
 	};
 };
 
@@ -261,8 +266,9 @@ mctp at 10 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1278";
+		compatible = "adi,adm1281";
 		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
 	};
 };
 
@@ -278,8 +284,9 @@ mctp at 10 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1278";
+		compatible = "adi,adm1281";
 		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
 	};
 };
 
@@ -295,8 +302,9 @@ mctp at 10 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1278";
+		compatible = "adi,adm1281";
 		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
 	};
 };
 
-- 
2.25.1

[PATCH v13 07/29] ARM: dts: aspeed: yosemite4: Add gpio pca9506

[Delphine CC Chiu]

Add gpio pca9506 I/O expander for yv4 use

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 252 ++++++++++++++++++
 1 file changed, 252 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 7b79fcd77c8c..f4d27f1ffdb8 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -175,6 +175,34 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	power-sensor at 40 {
 		compatible = "adi,adm1281";
 		reg = <0x40>;
@@ -193,6 +221,34 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	power-sensor at 40 {
 		compatible = "adi,adm1281";
 		reg = <0x40>;
@@ -211,6 +267,34 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	power-sensor at 40 {
 		compatible = "adi,adm1281";
 		reg = <0x40>;
@@ -229,6 +313,34 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	power-sensor at 40 {
 		compatible = "adi,adm1281";
 		reg = <0x40>;
@@ -247,6 +359,34 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	power-sensor at 40 {
 		compatible = "adi,adm1281";
 		reg = <0x40>;
@@ -265,6 +405,34 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	power-sensor at 40 {
 		compatible = "adi,adm1281";
 		reg = <0x40>;
@@ -283,6 +451,34 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	power-sensor at 40 {
 		compatible = "adi,adm1281";
 		reg = <0x40>;
@@ -301,6 +497,34 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	power-sensor at 40 {
 		compatible = "adi,adm1281";
 		reg = <0x40>;
@@ -690,6 +914,34 @@ ipmb at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 		i2c-protocol;
 	};
+
+	gpio at 20 {
+		compatible = "nxp,pca9506";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio at 23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
 };
 
 &i2c14 {
-- 
2.25.1

[PATCH v13 08/29] ARM: dts: aspeed: yosemite4: Remove space for adm1272 compatible

[Delphine CC Chiu]

Remove space for adm1272 compatible

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index f4d27f1ffdb8..b11951c2f71e 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -821,12 +821,12 @@ imux29: i2c at 1 {
 &i2c11 {
 	status = "okay";
 	power-sensor at 10 {
-		compatible = "adi, adm1272";
+		compatible = "adi,adm1272";
 		reg = <0x10>;
 	};
 
 	power-sensor at 12 {
-		compatible = "adi, adm1272";
+		compatible = "adi,adm1272";
 		reg = <0x12>;
 	};
 
-- 
2.25.1

[PATCH v13 08/29] ARM: dts: aspeed: yosemite4: Remove space for adm1272 compatible

[Krzysztof Kozlowski]

On 21/08/2024 11:40, Delphine CC Chiu wrote:
> Remove space for adm1272 compatible
> 
> Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
> ---

This should be marked with Fixes tag and sent at beginning of patchset
or even separate.

Best regards,
Krzysztof

[PATCH v13 09/29] ARM: dts: aspeed: yosemite4: Enable interrupt setting for pca9555

[Delphine CC Chiu]

Enable interrupt setting for pca9555

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 56 +++++++++++++++++--
 1 file changed, 52 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index b11951c2f71e..09bbbcb192f5 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -832,30 +832,78 @@ power-sensor at 12 {
 
 	gpio at 20 {
 		compatible = "nxp,pca9555";
-		reg = <0x20>;
+		pinctrl-names = "default";
 		gpio-controller;
 		#gpio-cells = <2>;
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <98 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+		"P48V_OCP_GPIO1","P48V_OCP_GPIO2",
+		"P48V_OCP_GPIO3","FAN_BOARD_0_REVISION_0_R",
+		"FAN_BOARD_0_REVISION_1_R","FAN_BOARD_1_REVISION_0_R",
+		"FAN_BOARD_1_REVISION_1_R","RST_MUX_R_N",
+		"RST_LED_CONTROL_FAN_BOARD_0_N","RST_LED_CONTROL_FAN_BOARD_1_N",
+		"RST_IOEXP_FAN_BOARD_0_N","RST_IOEXP_FAN_BOARD_1_N",
+		"PWRGD_LOAD_SWITCH_FAN_BOARD_0_R","PWRGD_LOAD_SWITCH_FAN_BOARD_1_R",
+		"","";
 	};
 
 	gpio at 21 {
 		compatible = "nxp,pca9555";
-		reg = <0x21>;
+		pinctrl-names = "default";
 		gpio-controller;
 		#gpio-cells = <2>;
+		reg = <0x21>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <98 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+		"HSC_OCP_SLOT_ODD_GPIO1","HSC_OCP_SLOT_ODD_GPIO2",
+		"HSC_OCP_SLOT_ODD_GPIO3","HSC_OCP_SLOT_EVEN_GPIO1",
+		"HSC_OCP_SLOT_EVEN_GPIO2","HSC_OCP_SLOT_EVEN_GPIO3",
+		"ADC_TYPE_0_R","ADC_TYPE_1_R",
+		"MEDUSA_BOARD_REV_0","MEDUSA_BOARD_REV_1",
+		"MEDUSA_BOARD_REV_2","MEDUSA_BOARD_TYPE",
+		"DELTA_MODULE_TYPE","P12V_HSC_TYPE",
+		"","";
 	};
 
 	gpio at 22 {
 		compatible = "nxp,pca9555";
-		reg = <0x22>;
+		pinctrl-names = "default";
 		gpio-controller;
 		#gpio-cells = <2>;
+		reg = <0x22>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <98 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+		"CARD_TYPE_SLOT1","CARD_TYPE_SLOT2",
+		"CARD_TYPE_SLOT3","CARD_TYPE_SLOT4",
+		"CARD_TYPE_SLOT5","CARD_TYPE_SLOT6",
+		"CARD_TYPE_SLOT7","CARD_TYPE_SLOT8",
+		"OC_P48V_HSC_0_N","FLT_P48V_HSC_0_N",
+		"OC_P48V_HSC_1_N","FLT_P48V_HSC_1_N",
+		"EN_P48V_AUX_0","EN_P48V_AUX_1",
+		"PWRGD_P12V_AUX_0","PWRGD_P12V_AUX_1";
 	};
 
 	gpio at 23 {
 		compatible = "nxp,pca9555";
-		reg = <0x23>;
+		pinctrl-names = "default";
 		gpio-controller;
 		#gpio-cells = <2>;
+		reg = <0x23>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <98 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+		"HSC1_ALERT1_R_N","HSC2_ALERT1_R_N",
+		"HSC3_ALERT1_R_N","HSC4_ALERT1_R_N",
+		"HSC5_ALERT1_R_N","HSC6_ALERT1_R_N",
+		"HSC7_ALERT1_R_N","HSC8_ALERT1_R_N",
+		"HSC1_ALERT2_R_N","HSC2_ALERT2_R_N",
+		"HSC3_ALERT2_R_N","HSC4_ALERT2_R_N",
+		"HSC5_ALERT2_R_N","HSC6_ALERT2_R_N",
+		"HSC7_ALERT2_R_N","HSC8_ALERT2_R_N";
 	};
 
 	temperature-sensor at 48 {
-- 
2.25.1

[PATCH v13 10/29] ARM: dts: aspeed: yosemite4: Add power sensor for power module reading

[Delphine CC Chiu]

Add power sensor for power module reading

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 25 +++++++++++++++++++
 1 file changed, 25 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 09bbbcb192f5..139a09de24cf 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -906,6 +906,11 @@ gpio at 23 {
 		"HSC7_ALERT2_R_N","HSC8_ALERT2_R_N";
 	};
 
+	power-sensor at 40 {
+		compatible = "mps,mp5023";
+		reg = <0x40>;
+	};
+
 	temperature-sensor at 48 {
 		compatible = "ti,tmp75";
 		reg = <0x48>;
@@ -930,6 +935,26 @@ eeprom at 54 {
 		compatible = "atmel,24c256";
 		reg = <0x54>;
 	};
+
+	power-sensor at 62 {
+		compatible = "pmbus";
+		reg = <0x62>;
+	};
+
+	power-sensor at 64 {
+		compatible = "pmbus";
+		reg = <0x64>;
+	};
+
+	power-sensor at 65 {
+		compatible = "pmbus";
+		reg = <0x65>;
+	};
+
+	power-sensor at 68 {
+		compatible = "pmbus";
+		reg = <0x68>;
+	};
 };
 
 &i2c12 {
-- 
2.25.1

[PATCH v13 11/29] ARM: dts: aspeed: yosemite4: Add eeprom for yosemite4 use

[Delphine CC Chiu]

Add eeprom for yosemite4 use

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 139a09de24cf..e83cb51ac19d 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -932,7 +932,7 @@ temperature-sensor at 4b {
 	};
 
 	eeprom at 54 {
-		compatible = "atmel,24c256";
+		compatible = "atmel,24c128";
 		reg = <0x54>;
 	};
 
@@ -971,6 +971,11 @@ eeprom at 50 {
 		reg = <0x50>;
 	};
 
+	eeprom at 54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
+
 	rtc at 6f {
 		compatible = "nuvoton,nct3018y";
 		reg = <0x6f>;
-- 
2.25.1

[PATCH v13 12/29] ARM: dts: aspeed: yosemite4: Remove temperature sensor for yosemite4 schematic change

[Delphine CC Chiu]

Remove temperature sensor for yosemite4 schematic change

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts  | 10 ----------
 1 file changed, 10 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index e83cb51ac19d..2c0c37b3ee5b 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -921,16 +921,6 @@ temperature-sensor at 49 {
 		reg = <0x49>;
 	};
 
-	temperature-sensor at 4a {
-		compatible = "ti,tmp75";
-		reg = <0x4a>;
-	};
-
-	temperature-sensor at 4b {
-		compatible = "ti,tmp75";
-		reg = <0x4b>;
-	};
-
 	eeprom at 54 {
 		compatible = "atmel,24c128";
 		reg = <0x54>;
-- 
2.25.1

[PATCH v13 13/29] ARM: dts: aspeed: yosemite4: Revise adc128d818 adc mode for yosemite4 schematic change

[Delphine CC Chiu]

Revise adc128d818 adc mode for yosemite4 schematic change

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts  | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 2c0c37b3ee5b..1765a0bb70d7 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1018,19 +1018,19 @@ &i2c14 {
 	adc at 1d {
 		compatible = "ti,adc128d818";
 		reg = <0x1d>;
-		ti,mode = /bits/ 8 <2>;
+		ti,mode = /bits/ 8 <1>;
 	};
 
-	adc at 35 {
+	adc at 36 {
 		compatible = "ti,adc128d818";
-		reg = <0x35>;
-		ti,mode = /bits/ 8 <2>;
+		reg = <0x36>;
+		ti,mode = /bits/ 8 <1>;
 	};
 
 	adc at 37 {
 		compatible = "ti,adc128d818";
 		reg = <0x37>;
-		ti,mode = /bits/ 8 <2>;
+		ti,mode = /bits/ 8 <1>;
 	};
 
 	power-sensor at 40 {
-- 
2.25.1

[PATCH v13 14/29] ARM: dts: aspeed: yosemite4: Revise ina233 config for yosemite4 schematic change

[Delphine CC Chiu]

Revise ina233 config for yosemite4 schematic change

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 20 ++++++++++++++-----
 1 file changed, 15 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 1765a0bb70d7..df389b506b4b 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1034,28 +1034,38 @@ adc at 37 {
 	};
 
 	power-sensor at 40 {
-		compatible = "ti,ina230";
+		compatible = "ti,ina233";
 		reg = <0x40>;
+		resistor-calibration = /bits/ 16 <0x0a00>;
+		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 41 {
-		compatible = "ti,ina230";
+		compatible = "ti,ina233";
 		reg = <0x41>;
+		resistor-calibration = /bits/ 16 <0x0a00>;
+		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 42 {
-		compatible = "ti,ina230";
+		compatible = "ti,ina233";
 		reg = <0x42>;
+		resistor-calibration = /bits/ 16 <0x0a00>;
+		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 43 {
-		compatible = "ti,ina230";
+		compatible = "ti,ina233";
 		reg = <0x43>;
+		resistor-calibration = /bits/ 16 <0x0a00>;
+		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 44 {
-		compatible = "ti,ina230";
+		compatible = "ti,ina233";
 		reg = <0x44>;
+		resistor-calibration = /bits/ 16 <0x0a00>;
+		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	temperature-sensor at 4e {
-- 
2.25.1

[PATCH v13 15/29] ARM: dts: aspeed: yosemite4: Remove idle state setting for yosemite4 NIC connection

[Delphine CC Chiu]

Remove idle state setting for yosemite4 NIC connection

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index df389b506b4b..c0497a1aa93e 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1235,7 +1235,6 @@ mctp at 10 {
 
 	i2c-mux at 72 {
 		compatible = "nxp,pca9544";
-		i2c-mux-idle-disconnect;
 		reg = <0x72>;
 
 		imux24: i2c at 0 {
-- 
2.25.1

[PATCH v13 16/29] ARM: dts: aspeed: yosemite4: Initialize bmc gpio state

[Delphine CC Chiu]

Initialize bmc gpio state

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 234 ++++++++++++++++++
 1 file changed, 234 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index c0497a1aa93e..60743f9829a5 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1304,3 +1304,237 @@ &ehci1 {
 &uhci {
 	status = "okay";
 };
+
+&sgpiom0 {
+	status = "okay";
+	ngpios = <128>;
+	bus-frequency = <48000>;
+};
+
+&pinctrl {
+	pinctrl_gpio0_unbiased: gpio0_unbiased {
+		/* GPIOB0, GPIOB1 */
+		pins = "J26", "K23";
+		bias-disable;
+	};
+	pinctrl_gpio2_unbiased: gpio2_unbiased {
+		/* GPIOI5, GPIOI6, GPIOI7,
+		   GPIOL6 */
+		pins = "E16", "B16", "A15", "B14";
+		bias-disable;
+	};
+	pinctrl_gpio3_unbiased: gpio3_unbiased {
+		/* GPIOM2, GPIOM3, GPIOM4, GPIOM5,
+		   GPION0, GPION1, GPION2, GPION3, GPION5,
+		   GPIOO0, GPIOO1, GPIOO2, GPIOO3,
+		   GPIOP0, GPIOP1, GPIOP2, GPIOP3, GPIOP4, GPIOP5, GPIOP6 */
+		pins = "A12", "E14", "B12", "C12", "P25", "N23", "N25", "N24", "M23", "AD26", "AD22", "AD23", "AD24", "AB22", "W24", "AA23", "AA24", "W23", "AB23", "AB24";
+		bias-disable;
+	};
+	pinctrl_gpio4_unbiased: gpio4_unbiased {
+		/* GPIOR0, GPIOR1, GPIOR2, GPIOR3, GPIOR4, GPIOR5, GPIOR6, GPIOR7
+		   GPIOS0, GPIOS1, GPIOS2, GPIOS3, GPIOS5, GPIOS6, GPIOS7 */
+		pins = "V25", "U24", "V24", "V26", "U25", "T23", "W26", "U26", "R23", "T25", "T26", "R24", "P24", "P23", "T24";
+		bias-disable;
+	};
+	pinctrl_gpio5_unbiased: gpio5_unbiased {
+		/* GPIOV0, GPIOV1, GPIOV2, GPIOV3, GPIOV4, GPIOV5, GPIOV6, GPIOV7
+		   GPIOX1, GPIOX2 */
+		pins = "AB15", "AF14", "AD14", "AC15", "AE15", "AE14", "AD15", "AF15", "AA9", "AC9";
+		bias-disable;
+	};
+	pinctrl_gpio6_unbiased: gpio6_unbiased {
+		/* GPIOY2, GPIOY5, GPIOY6
+		   GPIOZ0, GPIOZ1, GPIOZ3, GPIOZ4 */
+		pins = "AE11", "AF12", "AC12", "AC10", "AD10", "AB11", "AC11";
+		bias-disable;
+	};
+};
+
+&gpio0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpiu2_default &pinctrl_gpiu3_default
+		     &pinctrl_gpiu4_default &pinctrl_gpiu6_default
+		     &pinctrl_gpio0_unbiased &pinctrl_gpio2_unbiased
+		     &pinctrl_gpio3_unbiased &pinctrl_gpio4_unbiased
+		     &pinctrl_gpio5_unbiased &pinctrl_gpio6_unbiased>;
+	gpio-line-names =
+	/*A0-A7*/       "","","","","","","","",
+	/*B0-B7*/       "FLT_HSC_SERVER_SLOT8_N","AC_ON_OFF_BTN_CPLD_SLOT5_N",
+			"PWRGD_SLOT1_STBY","PWRGD_SLOT2_STBY",
+			"PWRGD_SLOT3_STBY","PWRGD_SLOT4_STBY","","",
+	/*C0-C7*/       "","","","","FM_NIC0_WAKE_N",
+			"FM_NIC1_WAKE_N","","RST_PCIE_SLOT2_N",
+	/*D0-D7*/       "","","","","","","","",
+	/*E0-E7*/       "PRSNT_NIC1_N","PRSNT_NIC2_N","","RST_PCIE_SLOT1_N",
+			"","","","",
+	/*F0-F7*/       "FM_RESBTN_SLOT1_BMC_N","FM_RESBTN_SLOT2_BMC_N",
+			"FM_RESBTN_SLOT3_BMC_N","FM_RESBTN_SLOT4_BMC_N",
+			"PRSNT_SB_SLOT1_N","PRSNT_SB_SLOT2_N",
+			"PRSNT_SB_SLOT3_N","PRSNT_SB_SLOT4_N",
+	/*G0-G7*/       "","","","","","","","",
+	/*H0-H7*/       "","","","","","","","",
+	/*I0-I7*/       "","","","","","ALT_MEDUSA_ADC_N",
+			"ALT_SMB_BMC_CPLD2_N",
+			"INT_SPIDER_ADC_R_N",
+	/*J0-J7*/       "","","","","","","","",
+	/*K0-K7*/       "","","","","","","","",
+	/*L0-L7*/       "","","","","","","ALT_MEDUSA_P12V_EFUSE_N","",
+	/*M0-M7*/       "EN_NIC0_POWER_BMC_R","EN_NIC1_POWER_BMC_R",
+			"INT_MEDUSA_IOEXP_TEMP_N","PRSNT_NIC3_N",
+			"INT_SMB_BMC_SLOT1_4_BMC_N",
+			"AC_ON_OFF_BTN_CPLD_SLOT6_N","","",
+	/*N0-N7*/       "FLT_HSC_SERVER_SLOT1_N","FLT_HSC_SERVER_SLOT2_N",
+			"FLT_HSC_SERVER_SLOT3_N","FLT_HSC_SERVER_SLOT4_N",
+			"FM_BMC_READY_R2","RST_SMB_NIC0_R_N","","",
+	/*O0-O7*/       "AC_ON_OFF_BTN_CPLD_SLOT8_N","RST_SMB_NIC1_R_N",
+			"RST_SMB_NIC2_R_N","RST_SMB_NIC3_R_N",
+			"","","","",
+	/*P0-P7*/       "ALT_SMB_BMC_CPLD1_N","BTN_BMC_R2_N",
+			"EN_P3V_BAT_SCALED_R","PWRGD_P5V_USB_BMC",
+			"FM_BMC_RTCRST_R","RST_USB_HUB_R_N",
+			"FLAG_P5V_USB_BMC_N","",
+	/*Q0-Q7*/       "AC_ON_OFF_BTN_CPLD_SLOT1_N","AC_ON_OFF_BTN_CPLD_SLOT2_N",
+			"AC_ON_OFF_BTN_CPLD_SLOT3_N","AC_ON_OFF_BTN_CPLD_SLOT4_N",
+			"PRSNT_SB_SLOT5_N","PRSNT_SB_SLOT6_N",
+			"PRSNT_SB_SLOT7_N","PRSNT_SB_SLOT8_N",
+	/*R0-R7*/       "AC_ON_OFF_BTN_CPLD_SLOT7_N","INT_SMB_BMC_SLOT5_8_BMC_N",
+			"FM_PWRBRK_NIC_BMC_R2","RST_PCIE_SLOT4_N",
+			"RST_PCIE_SLOT5_N","RST_PCIE_SLOT6_N",
+			"RST_PCIE_SLOT7_N","RST_PCIE_SLOT8_N",
+	/*S0-S7*/       "FM_NIC2_WAKE_N","FM_NIC3_WAKE_N",
+			"EN_NIC3_POWER_BMC_R","SEL_BMC_JTAG_MUX_R",
+			"","ALT_P12V_AUX_N","FAST_PROCHOT_N",
+			"SPI_WP_DISABLE_STATUS_R_N",
+	/*T0-T7*/       "","","","","","","","",
+	/*U0-U7*/       "","","RST_PCIE_SLOT3_N","",
+			"","PRSNT_NIC0_N","","",
+	/*V0-V7*/       "FM_RESBTN_SLOT5_BMC_N","FM_RESBTN_SLOT6_BMC_N",
+			"FM_RESBTN_SLOT7_BMC_N","FM_RESBTN_SLOT8_BMC_N",
+			"","","","",
+	/*W0-W7*/       "PRSNT_TPM_BMC_N","PRSNT_OCP_DEBUG_BMC_N","ALT_TEMP_BMC_N","ALT_RTC_BMC_N",
+			"","","","",
+	/*X0-X7*/       "","LT_HSC_SERVER_SLOT6_N","FLT_HSC_SERVER_SLOT7_N","","","",
+			"PWRGD_SLOT5_STBY","PWRGD_SLOT6_STBY",
+	/*Y0-Y7*/       "","","SPI_LOCK_REQ_BMC_N","PWRGD_SLOT7_STBY",
+			"","","EN_NIC2_POWER_BMC_R","",
+	/*Z0-Z7*/       "EN_P5V_USB_CPLD_R","FLT_HSC_SERVER_SLOT5_N",
+			"PWRGD_SLOT8_STBY","","","","","";
+
+	pin_gpio_b4 {
+		gpios = <ASPEED_GPIO(B, 4) GPIO_ACTIVE_HIGH>;
+		input;
+	};
+	pin_gpio_b5 {
+		gpios = <ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
+		input;
+	};
+	pin_gpio_f0 {
+		gpios = <ASPEED_GPIO(F, 0) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_f1 {
+		gpios = <ASPEED_GPIO(F, 1) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_f2 {
+		gpios = <ASPEED_GPIO(F, 2) GPIO_ACTIVE_LOW>;
+		input;
+		};
+	pin_gpio_f3 {
+		gpios = <ASPEED_GPIO(F, 3) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_f4 {
+		gpios = <ASPEED_GPIO(F, 4) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_f5 {
+		gpios = <ASPEED_GPIO(F, 5) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_f6 {
+		gpios = <ASPEED_GPIO(F, 6) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_f7 {
+		gpios = <ASPEED_GPIO(F, 7) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_l6 {
+		gpios = <ASPEED_GPIO(L, 6) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_l7 {
+		gpios = <ASPEED_GPIO(L, 7) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_s0 {
+		gpios = <ASPEED_GPIO(S, 0) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_s1 {
+		gpios = <ASPEED_GPIO(S, 1) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_v0 {
+		gpios = <ASPEED_GPIO(V, 0) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_v1 {
+		gpios = <ASPEED_GPIO(V, 1) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_v2 {
+		gpios = <ASPEED_GPIO(V, 2) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_v3 {
+		gpios = <ASPEED_GPIO(V, 3) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_w0 {
+		gpios = <ASPEED_GPIO(W, 0) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_w1 {
+		gpios = <ASPEED_GPIO(W, 1) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_w2 {
+		gpios = <ASPEED_GPIO(W, 2) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_w3 {
+		gpios = <ASPEED_GPIO(W, 3) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_w4 {
+		gpios = <ASPEED_GPIO(W, 4) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_w5 {
+		gpios = <ASPEED_GPIO(W, 5) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_w6 {
+		gpios = <ASPEED_GPIO(W, 6) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_w7 {
+		gpios = <ASPEED_GPIO(W, 7) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_z3 {
+		gpios = <ASPEED_GPIO(Z, 3) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_z4 {
+		gpios = <ASPEED_GPIO(Z, 4) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_z5 {
+		gpios = <ASPEED_GPIO(Z, 5) GPIO_ACTIVE_LOW>;
+		input;
+	};
+};
-- 
2.25.1

[PATCH v13 17/29] ARM: dts: aspeed: yosemite4: Revise mx31790 fan tach config

[Delphine CC Chiu]

Revise fan tach config for max31790 driver change

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 48 +++++++++++++++++--
 1 file changed, 44 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 60743f9829a5..b46a0b9940e2 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1103,8 +1103,18 @@ adc at 1f {
 
 			pwm at 20{
 				compatible = "maxim,max31790";
-				pwm-as-tach = <4 5>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0x20>;
+				channel at 4 {
+					reg = <4>;
+					sensor-type = "TACH";
+				};
+
+				channel at 5 {
+					reg = <5>;
+					sensor-type = "TACH";
+				};
 			};
 
 			gpio at 22{
@@ -1116,8 +1126,18 @@ gpio at 22{
 
 			pwm at 2f{
 				compatible = "maxim,max31790";
-				pwm-as-tach = <4 5>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0x2f>;
+				channel at 4 {
+					reg = <4>;
+					sensor-type = "TACH";
+				};
+
+				channel at 5 {
+					reg = <5>;
+					sensor-type = "TACH";
+				};
 			};
 
 			adc at 33 {
@@ -1153,8 +1173,18 @@ adc at 1f {
 
 			pwm at 20{
 				compatible = "maxim,max31790";
-				pwm-as-tach = <4 5>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0x20>;
+				channel at 4 {
+					reg = <4>;
+					sensor-type = "TACH";
+				};
+
+				channel at 5 {
+					reg = <5>;
+					sensor-type = "TACH";
+				};
 			};
 
 			gpio at 22{
@@ -1166,8 +1196,18 @@ gpio at 22{
 
 			pwm at 2f{
 				compatible = "maxim,max31790";
-				pwm-as-tach = <4 5>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0x2f>;
+				channel at 4 {
+					reg = <4>;
+					sensor-type = "TACH";
+				};
+
+				channel at 5 {
+					reg = <5>;
+					sensor-type = "TACH";
+				};
 			};
 
 			adc at 33 {
-- 
2.25.1

[PATCH v13 18/29] ARM: dts: aspeed: yosemite4: add mctp config for NIC

[Delphine CC Chiu]

add mctp config for NIC

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 24 +++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index b46a0b9940e2..7b8a2384d99d 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1281,40 +1281,64 @@ imux24: i2c at 0 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0>;
+			mctp-controller;
 			temperature-sensor at 1f {
 				compatible = "ti,tmp421";
 				reg = <0x1f>;
 			};
+
+			temperature-sensor at 3c {
+				compatible = "smsc,emc1403";
+				reg = <0x3c>;
+			};
 		};
 
 		imux25: i2c at 1 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <1>;
+			mctp-controller;
 			temperature-sensor at 1f {
 				compatible = "ti,tmp421";
 				reg = <0x1f>;
 			};
+
+			temperature-sensor at 3c {
+				compatible = "smsc,emc1403";
+				reg = <0x3c>;
+			};
 		};
 
 		imux26: i2c at 2 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <2>;
+			mctp-controller;
 			temperature-sensor at 1f {
 				compatible = "ti,tmp421";
 				reg = <0x1f>;
 			};
+
+			temperature-sensor at 3c {
+				compatible = "smsc,emc1403";
+				reg = <0x3c>;
+			};
 		};
 
 		imux27: i2c at 3 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <3>;
+			mctp-controller;
 			temperature-sensor at 1f {
 				compatible = "ti,tmp421";
 				reg = <0x1f>;
 			};
+
+			temperature-sensor at 3c {
+				compatible = "smsc,emc1403";
+				reg = <0x3c>;
+			};
 		};
 	};
 };
-- 
2.25.1

[PATCH v13 19/29] ARM: dts: aspeed: yosemite4: support mux to cpld

[Delphine CC Chiu]

Mux pca9544 to cpld was added on EVT HW schematic design,
so add dts setting for devices behind mux pca9544 to cpld

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 64 ++++++++++++++-----
 1 file changed, 49 insertions(+), 15 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 7b8a2384d99d..98eeee49b082 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -36,6 +36,10 @@ aliases {
 		i2c31 = &imux31;
 		i2c32 = &imux32;
 		i2c33 = &imux33;
+		i2c34 = &imux34;
+		i2c35 = &imux35;
+		i2c36 = &imux36;
+		i2c37 = &imux37;
 	};
 
 	chosen {
@@ -951,24 +955,54 @@ &i2c12 {
 	status = "okay";
 	bus-frequency = <400000>;
 
-	temperature-sensor at 48 {
-		compatible = "ti,tmp75";
-		reg = <0x48>;
-	};
+	i2c-mux at 70 {
+		compatible = "nxp,pca9544";
+		i2c-mux-idle-disconnect;
+		reg = <0x70>;
 
-	eeprom at 50 {
-		compatible = "atmel,24c128";
-		reg = <0x50>;
-	};
+		imux34: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
 
-	eeprom at 54 {
-		compatible = "atmel,24c64";
-		reg = <0x54>;
-	};
+			temperature-sensor at 48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
 
-	rtc at 6f {
-		compatible = "nuvoton,nct3018y";
-		reg = <0x6f>;
+			eeprom at 54 {
+				compatible = "atmel,24c64";
+				reg = <0x54>;
+			};
+
+			rtc at 6f {
+				compatible = "nuvoton,nct3018y";
+				reg = <0x6f>;
+			};
+		};
+
+		imux35: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux36: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux37: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
 	};
 };
 
-- 
2.25.1

[PATCH v13 20/29] ARM: dts: aspeed: yosemite4: support medusa board adc sensors

[Delphine CC Chiu]

Add ina233/ina28 support for medusa board adc sensors

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../dts/aspeed/aspeed-bmc-facebook-yosemite4.dts    | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 98eeee49b082..49500db53a13 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -915,6 +915,19 @@ power-sensor at 40 {
 		reg = <0x40>;
 	};
 
+	power-sensor at 41 {
+			compatible = "ti,ina233";
+			resistor-calibration = /bits/ 16 <0x0a00>;
+			current-lsb= /bits/ 16 <0x0001>;
+			reg = <0x41>;
+	};
+
+	power-sensor at 44 {
+			compatible = "ti,ina238";
+			shunt-resistor = <1000>;
+			reg = <0x44>;
+	};
+
 	temperature-sensor at 48 {
 		compatible = "ti,tmp75";
 		reg = <0x48>;
-- 
2.25.1

[PATCH v13 21/29] ARM: dts: aspeed: yosemite4: support NIC eeprom

[Delphine CC Chiu]

Add NIC eeprom devicetree config

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 20 +++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 49500db53a13..c2994651e747 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1338,6 +1338,11 @@ temperature-sensor at 3c {
 				compatible = "smsc,emc1403";
 				reg = <0x3c>;
 			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
 		};
 
 		imux25: i2c at 1 {
@@ -1354,6 +1359,11 @@ temperature-sensor at 3c {
 				compatible = "smsc,emc1403";
 				reg = <0x3c>;
 			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
 		};
 
 		imux26: i2c at 2 {
@@ -1370,6 +1380,11 @@ temperature-sensor at 3c {
 				compatible = "smsc,emc1403";
 				reg = <0x3c>;
 			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
 		};
 
 		imux27: i2c at 3 {
@@ -1386,6 +1401,11 @@ temperature-sensor at 3c {
 				compatible = "smsc,emc1403";
 				reg = <0x3c>;
 			};
+
+			eeprom at 50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
 		};
 	};
 };
-- 
2.25.1

[PATCH v13 22/29] ARM: dts: aspeed: yosemite4: Revise i2c duty-cycle

[Delphine CC Chiu]

Revise duty cycle SMB11 and SMB16 to high: 40%, low: 60%,
to meet 400kHz-i2c clock low time spec (> 1.3 us) from EE request

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index c2994651e747..c940d23c8a4b 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -761,6 +761,7 @@ eeprom at 54 {
 &i2c10 {
 	status = "okay";
 	bus-frequency = <400000>;
+	i2c-clk-high-min-percent = <40>;
 	i2c-mux at 74 {
 		compatible = "nxp,pca9544";
 		i2c-mux-idle-disconnect;
@@ -1314,6 +1315,7 @@ &i2c15 {
 	mctp-controller;
 	multi-master;
 	bus-frequency = <400000>;
+	i2c-clk-high-min-percent = <40>;
 
 	mctp at 10 {
 		compatible = "mctp-i2c-controller";
-- 
2.25.1

[PATCH v13 23/29] ARM: dts: aspeed: yosemite4: add fan led config

[Delphine CC Chiu]

Set fan led config in yosemite4 DTS.

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 152 +++++++++++++++++-
 1 file changed, 150 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index c940d23c8a4b..2f4e9c5edd5a 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -75,6 +75,154 @@ tpmdev at 0 {
 			reg = <0>;
 		};
 	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		fan0_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio0 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan0_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio0 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan1_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio0 10 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan1_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio0 11 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan2_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio1 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan2_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio1 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan3_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio1 10 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan3_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio1 11 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan4_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio0 2 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan4_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio0 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan5_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio0 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan5_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio0 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan6_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio1 2 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan6_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio1 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan7_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio1 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan7_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio1 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan8_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio0 0 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan8_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio0 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan9_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio0 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan9_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio0 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan10_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio1 0 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan10_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio1 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan11_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&led_gpio1 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		fan11_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&led_gpio1 7 GPIO_ACTIVE_HIGH>;
+		};
+	};
 };
 
 &uart1 {
@@ -1198,7 +1346,7 @@ eeprom at 52 {
 				reg = <0x52>;
 			};
 
-			gpio at 61 {
+			led_gpio0: gpio at 61 {
 				compatible = "nxp,pca9552";
 				reg = <0x61>;
 				#address-cells = <1>;
@@ -1268,7 +1416,7 @@ eeprom at 52 {
 				reg = <0x52>;
 			};
 
-			gpio at 61 {
+			led_gpio1: gpio at 61 {
 				compatible = "nxp,pca9552";
 				reg = <0x61>;
 				#address-cells = <1>;
-- 
2.25.1

[PATCH v13 24/29] ARM: dts: aspeed: yosemite4: add XDP710

[Delphine CC Chiu]

Add XDP710 in yosemite4 DTS.

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts  | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 2f4e9c5edd5a..f73719b3c2f1 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -978,11 +978,21 @@ power-sensor at 10 {
 		reg = <0x10>;
 	};
 
+	power-sensor at 11 {
+		compatible = "infineon,xdp710";
+		reg = <0x11>;
+	};
+
 	power-sensor at 12 {
 		compatible = "adi,adm1272";
 		reg = <0x12>;
 	};
 
+	power-sensor at 13 {
+		compatible = "infineon,xdp710";
+		reg = <0x13>;
+	};
+
 	gpio at 20 {
 		compatible = "nxp,pca9555";
 		pinctrl-names = "default";
-- 
2.25.1

[PATCH v13 25/29] ARM: dts: aspeed: yosemite4: add RTQ6056 support

[Delphine CC Chiu]

Add RTQ6056 (spider board 3rd source) support in yosemite4 DTS.

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts  | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index f73719b3c2f1..03a1e41312e3 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1240,35 +1240,35 @@ adc at 37 {
 	};
 
 	power-sensor at 40 {
-		compatible = "ti,ina233";
+		compatible = "ti,ina233", "richtek,rtq6056";
 		reg = <0x40>;
 		resistor-calibration = /bits/ 16 <0x0a00>;
 		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 41 {
-		compatible = "ti,ina233";
+		compatible = "ti,ina233", "richtek,rtq6056";
 		reg = <0x41>;
 		resistor-calibration = /bits/ 16 <0x0a00>;
 		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 42 {
-		compatible = "ti,ina233";
+		compatible = "ti,ina233", "richtek,rtq6056";
 		reg = <0x42>;
 		resistor-calibration = /bits/ 16 <0x0a00>;
 		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 43 {
-		compatible = "ti,ina233";
+		compatible = "ti,ina233", "richtek,rtq6056";
 		reg = <0x43>;
 		resistor-calibration = /bits/ 16 <0x0a00>;
 		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 44 {
-		compatible = "ti,ina233";
+		compatible = "ti,ina233", "richtek,rtq6056";
 		reg = <0x44>;
 		resistor-calibration = /bits/ 16 <0x0a00>;
 		current-lsb= /bits/ 16 <0x0001>;
-- 
2.25.1

[PATCH v13 26/29] ARM: dts: aspeed: yosemite4: add MP5990 support

[Delphine CC Chiu]

Add MP5990 in yosemite4 DTS.

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../dts/aspeed/aspeed-bmc-facebook-yosemite4.dts | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 03a1e41312e3..f139f426099e 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -356,7 +356,7 @@ gpio at 24 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1281";
+		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
 		shunt-resistor-micro-ohms = <500>;
 	};
@@ -402,7 +402,7 @@ gpio at 24 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1281";
+		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
 		shunt-resistor-micro-ohms = <500>;
 	};
@@ -448,7 +448,7 @@ gpio at 24 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1281";
+		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
 		shunt-resistor-micro-ohms = <500>;
 	};
@@ -494,7 +494,7 @@ gpio at 24 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1281";
+		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
 		shunt-resistor-micro-ohms = <500>;
 	};
@@ -540,7 +540,7 @@ gpio at 24 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1281";
+		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
 		shunt-resistor-micro-ohms = <500>;
 	};
@@ -586,7 +586,7 @@ gpio at 24 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1281";
+		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
 		shunt-resistor-micro-ohms = <500>;
 	};
@@ -632,7 +632,7 @@ gpio at 24 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1281";
+		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
 		shunt-resistor-micro-ohms = <500>;
 	};
@@ -678,7 +678,7 @@ gpio at 24 {
 	};
 
 	power-sensor at 40 {
-		compatible = "adi,adm1281";
+		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
 		shunt-resistor-micro-ohms = <500>;
 	};
-- 
2.25.1

[PATCH v13 27/29] ARM: dts: aspeed: yosemite4: Adjust ioexp bus and remove mctp driver

[Delphine CC Chiu]

Adjust CPLD io expender for PVT stage.
Add GPIO name for GPIOO7.
Only binding MCTP driver on the down-stream port of the mux.
Remove unnecessary driver binding since there's no MCTP device before the mux.

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 59 +++++++++----------
 1 file changed, 29 insertions(+), 30 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index f139f426099e..abd4a9173de4 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1156,6 +1156,34 @@ rtc at 6f {
 				compatible = "nuvoton,nct3018y";
 				reg = <0x6f>;
 			};
+
+			gpio at 20 {
+				compatible = "nxp,pca9506";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio at 21 {
+				compatible = "nxp,pca9506";
+				reg = <0x21>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio at 22 {
+				compatible = "nxp,pca9506";
+				reg = <0x22>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio at 23 {
+				compatible = "nxp,pca9506";
+				reg = <0x23>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
 		};
 
 		imux35: i2c at 1 {
@@ -1188,34 +1216,6 @@ ipmb at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 		i2c-protocol;
 	};
-
-	gpio at 20 {
-		compatible = "nxp,pca9506";
-		reg = <0x20>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	gpio at 21 {
-		compatible = "nxp,pca9506";
-		reg = <0x21>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	gpio at 22 {
-		compatible = "nxp,pca9506";
-		reg = <0x22>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	gpio at 23 {
-		compatible = "nxp,pca9506";
-		reg = <0x23>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
 };
 
 &i2c14 {
@@ -1470,7 +1470,6 @@ adc at 35 {
 
 &i2c15 {
 	status = "okay";
-	mctp-controller;
 	multi-master;
 	bus-frequency = <400000>;
 	i2c-clk-high-min-percent = <40>;
@@ -1680,7 +1679,7 @@ &pinctrl_gpio3_unbiased &pinctrl_gpio4_unbiased
 			"FM_BMC_READY_R2","RST_SMB_NIC0_R_N","","",
 	/*O0-O7*/       "AC_ON_OFF_BTN_CPLD_SLOT8_N","RST_SMB_NIC1_R_N",
 			"RST_SMB_NIC2_R_N","RST_SMB_NIC3_R_N",
-			"","","","",
+			"","","","FM_BMC_SLED_CYCLE_R",
 	/*P0-P7*/       "ALT_SMB_BMC_CPLD1_N","BTN_BMC_R2_N",
 			"EN_P3V_BAT_SCALED_R","PWRGD_P5V_USB_BMC",
 			"FM_BMC_RTCRST_R","RST_USB_HUB_R_N",
-- 
2.25.1

[PATCH v13 28/29] ARM: dts: aspeed: yosemite4: fix GPIO linename typo

[Delphine CC Chiu]

Fix GPIO linename typo and add missing GPIO pin initial state.

Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 554 ++++++++++++++----
 1 file changed, 455 insertions(+), 99 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index abd4a9173de4..4090725160f9 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -285,6 +285,8 @@ &mac2 {
 	pinctrl-0 = <&pinctrl_rmii3_default>;
 	use-ncsi;
 	mellanox,multi-host;
+	ncsi-ctrl,start-redo-probe;
+	ncsi-ctrl,no-channel-monitor;
 };
 
 &mac3 {
@@ -293,6 +295,8 @@ &mac3 {
 	pinctrl-0 = <&pinctrl_rmii4_default>;
 	use-ncsi;
 	mellanox,multi-host;
+	ncsi-ctrl,start-redo-probe;
+	ncsi-ctrl,no-channel-monitor;
 };
 
 &fmc {
@@ -327,6 +331,13 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	gpio at 21 {
 		compatible = "nxp,pca9506";
 		reg = <0x21>;
@@ -348,13 +359,6 @@ gpio at 23 {
 		#gpio-cells = <2>;
 	};
 
-	gpio at 24 {
-		compatible = "nxp,pca9506";
-		reg = <0x24>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
 	power-sensor at 40 {
 		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
@@ -373,6 +377,13 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	gpio at 21 {
 		compatible = "nxp,pca9506";
 		reg = <0x21>;
@@ -394,13 +405,6 @@ gpio at 23 {
 		#gpio-cells = <2>;
 	};
 
-	gpio at 24 {
-		compatible = "nxp,pca9506";
-		reg = <0x24>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
 	power-sensor at 40 {
 		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
@@ -419,6 +423,13 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	gpio at 21 {
 		compatible = "nxp,pca9506";
 		reg = <0x21>;
@@ -440,13 +451,6 @@ gpio at 23 {
 		#gpio-cells = <2>;
 	};
 
-	gpio at 24 {
-		compatible = "nxp,pca9506";
-		reg = <0x24>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
 	power-sensor at 40 {
 		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
@@ -465,6 +469,13 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	gpio at 21 {
 		compatible = "nxp,pca9506";
 		reg = <0x21>;
@@ -486,13 +497,6 @@ gpio at 23 {
 		#gpio-cells = <2>;
 	};
 
-	gpio at 24 {
-		compatible = "nxp,pca9506";
-		reg = <0x24>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
 	power-sensor at 40 {
 		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
@@ -511,6 +515,13 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	gpio at 21 {
 		compatible = "nxp,pca9506";
 		reg = <0x21>;
@@ -532,13 +543,6 @@ gpio at 23 {
 		#gpio-cells = <2>;
 	};
 
-	gpio at 24 {
-		compatible = "nxp,pca9506";
-		reg = <0x24>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
 	power-sensor at 40 {
 		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
@@ -557,6 +561,13 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	gpio at 21 {
 		compatible = "nxp,pca9506";
 		reg = <0x21>;
@@ -578,13 +589,6 @@ gpio at 23 {
 		#gpio-cells = <2>;
 	};
 
-	gpio at 24 {
-		compatible = "nxp,pca9506";
-		reg = <0x24>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
 	power-sensor at 40 {
 		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
@@ -603,6 +607,13 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	gpio at 21 {
 		compatible = "nxp,pca9506";
 		reg = <0x21>;
@@ -624,13 +635,6 @@ gpio at 23 {
 		#gpio-cells = <2>;
 	};
 
-	gpio at 24 {
-		compatible = "nxp,pca9506";
-		reg = <0x24>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
 	power-sensor at 40 {
 		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
@@ -649,6 +653,13 @@ mctp at 10 {
 		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
+	gpio at 24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	gpio at 21 {
 		compatible = "nxp,pca9506";
 		reg = <0x21>;
@@ -670,13 +681,6 @@ gpio at 23 {
 		#gpio-cells = <2>;
 	};
 
-	gpio at 24 {
-		compatible = "nxp,pca9506";
-		reg = <0x24>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
 	power-sensor at 40 {
 		compatible = "adi,adm1281", "mps,mp5990";
 		reg = <0x40>;
@@ -687,6 +691,7 @@ power-sensor at 40 {
 &i2c8 {
 	status = "okay";
 	bus-frequency = <400000>;
+	i2c-clk-high-min-percent = <40>;
 	i2c-mux at 70 {
 		compatible = "nxp,pca9544";
 		i2c-mux-idle-disconnect;
@@ -798,6 +803,7 @@ eeprom at 54 {
 &i2c9 {
 	status = "okay";
 	bus-frequency = <400000>;
+	i2c-clk-high-min-percent = <40>;
 	i2c-mux at 71 {
 		compatible = "nxp,pca9544";
 		i2c-mux-idle-disconnect;
@@ -993,7 +999,7 @@ power-sensor at 13 {
 		reg = <0x13>;
 	};
 
-	gpio at 20 {
+	gpio_ext1: pca9555 at 20 {
 		compatible = "nxp,pca9555";
 		pinctrl-names = "default";
 		gpio-controller;
@@ -1012,7 +1018,7 @@ gpio at 20 {
 		"","";
 	};
 
-	gpio at 21 {
+	gpio_ext2: pca9555 at 21 {
 		compatible = "nxp,pca9555";
 		pinctrl-names = "default";
 		gpio-controller;
@@ -1031,7 +1037,7 @@ gpio at 21 {
 		"","";
 	};
 
-	gpio at 22 {
+	gpio_ext3: pca9555 at 22 {
 		compatible = "nxp,pca9555";
 		pinctrl-names = "default";
 		gpio-controller;
@@ -1050,7 +1056,7 @@ gpio at 22 {
 		"PWRGD_P12V_AUX_0","PWRGD_P12V_AUX_1";
 	};
 
-	gpio at 23 {
+	gpio_ext4: pca9555 at 23 {
 		compatible = "nxp,pca9555";
 		pinctrl-names = "default";
 		gpio-controller;
@@ -1070,21 +1076,21 @@ gpio at 23 {
 	};
 
 	power-sensor at 40 {
-		compatible = "mps,mp5023";
-		reg = <0x40>;
+			compatible = "mps,mp5023";
+			reg = <0x40>;
 	};
 
 	power-sensor at 41 {
-			compatible = "ti,ina233";
-			resistor-calibration = /bits/ 16 <0x0a00>;
-			current-lsb= /bits/ 16 <0x0001>;
-			reg = <0x41>;
+		compatible = "ti,ina233";
+		resistor-calibration = /bits/ 16 <0x0a00>;
+		current-lsb= /bits/ 16 <0x0001>;
+		reg = <0x41>;
 	};
 
 	power-sensor at 44 {
-			compatible = "ti,ina238";
-			shunt-resistor = <1000>;
-			reg = <0x44>;
+		compatible = "ti,ina238";
+		shunt-resistor = <1000>;
+		reg = <0x44>;
 	};
 
 	temperature-sensor at 48 {
@@ -1156,33 +1162,32 @@ rtc at 6f {
 				compatible = "nuvoton,nct3018y";
 				reg = <0x6f>;
 			};
-
 			gpio at 20 {
-				compatible = "nxp,pca9506";
-				reg = <0x20>;
-				gpio-controller;
-				#gpio-cells = <2>;
+					compatible = "nxp,pca9506";
+					reg = <0x20>;
+					gpio-controller;
+					#gpio-cells = <2>;
 			};
 
 			gpio at 21 {
-				compatible = "nxp,pca9506";
-				reg = <0x21>;
-				gpio-controller;
-				#gpio-cells = <2>;
+					compatible = "nxp,pca9506";
+					reg = <0x21>;
+					gpio-controller;
+					#gpio-cells = <2>;
 			};
 
 			gpio at 22 {
-				compatible = "nxp,pca9506";
-				reg = <0x22>;
-				gpio-controller;
-				#gpio-cells = <2>;
+					compatible = "nxp,pca9506";
+					reg = <0x22>;
+					gpio-controller;
+					#gpio-cells = <2>;
 			};
 
 			gpio at 23 {
-				compatible = "nxp,pca9506";
-				reg = <0x23>;
-				gpio-controller;
-				#gpio-cells = <2>;
+					compatible = "nxp,pca9506";
+					reg = <0x23>;
+					gpio-controller;
+					#gpio-cells = <2>;
 			};
 		};
 
@@ -1242,35 +1247,35 @@ adc at 37 {
 	power-sensor at 40 {
 		compatible = "ti,ina233", "richtek,rtq6056";
 		reg = <0x40>;
-		resistor-calibration = /bits/ 16 <0x0a00>;
+		resistor-calibration = /bits/ 16 <0x0400>;
 		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 41 {
 		compatible = "ti,ina233", "richtek,rtq6056";
 		reg = <0x41>;
-		resistor-calibration = /bits/ 16 <0x0a00>;
+		resistor-calibration = /bits/ 16 <0x0400>;
 		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 42 {
 		compatible = "ti,ina233", "richtek,rtq6056";
 		reg = <0x42>;
-		resistor-calibration = /bits/ 16 <0x0a00>;
+		resistor-calibration = /bits/ 16 <0x0400>;
 		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 43 {
 		compatible = "ti,ina233", "richtek,rtq6056";
 		reg = <0x43>;
-		resistor-calibration = /bits/ 16 <0x0a00>;
+		resistor-calibration = /bits/ 16 <0x0400>;
 		current-lsb= /bits/ 16 <0x0001>;
 	};
 
 	power-sensor at 44 {
 		compatible = "ti,ina233", "richtek,rtq6056";
 		reg = <0x44>;
-		resistor-calibration = /bits/ 16 <0x0a00>;
+		resistor-calibration = /bits/ 16 <0x0400>;
 		current-lsb= /bits/ 16 <0x0001>;
 	};
 
@@ -1323,6 +1328,42 @@ channel at 5 {
 				};
 			};
 
+			hwmon0: hwmon at 21 {
+				compatible = "nuvoton,nct7363";
+				reg = <0x21>;
+				#pwm-cells = <2>;
+
+				fan-3 {
+					pwms = <&hwmon0 2 20000>;
+					tach-ch = /bits/ 8 <0x00>;
+				};
+
+				fan-4 {
+					pwms = <&hwmon0 5 20000>;
+					tach-ch = /bits/ 8 <0x01>;
+				};
+
+				fan-5 {
+					pwms = <&hwmon0 5 20000>;
+					tach-ch = /bits/ 8 <0x02>;
+				};
+
+				fan-0 {
+					pwms = <&hwmon0 0 20000>;
+					tach-ch = /bits/ 8 <0x09>;
+				};
+
+				fan-1 {
+					pwms = <&hwmon0 0 20000>;
+					tach-ch = /bits/ 8 <0x0c>;
+				};
+
+				fan-2 {
+					pwms = <&hwmon0 2 20000>;
+					tach-ch = /bits/ 8 <0x0e>;
+				};
+			};
+
 			gpio at 22{
 				compatible = "ti,tca6424";
 				reg = <0x22>;
@@ -1330,6 +1371,42 @@ gpio at 22{
 				#gpio-cells = <2>;
 			};
 
+			hwmon1: hwmon at 23 {
+				compatible = "nuvoton,nct7363";
+				reg = <0x23>;
+				#pwm-cells = <2>;
+
+				fan-3 {
+					pwms = <&hwmon0 2 20000>;
+					tach-ch = /bits/ 8 <0x00>;
+				};
+
+				fan-4 {
+					pwms = <&hwmon0 5 20000>;
+					tach-ch = /bits/ 8 <0x01>;
+				};
+
+				fan-5 {
+					pwms = <&hwmon0 5 20000>;
+					tach-ch = /bits/ 8 <0x02>;
+				};
+
+				fan-0 {
+					pwms = <&hwmon0 0 20000>;
+					tach-ch = /bits/ 8 <0x09>;
+				};
+
+				fan-1 {
+					pwms = <&hwmon0 0 20000>;
+					tach-ch = /bits/ 8 <0x0c>;
+				};
+
+				fan-2 {
+					pwms = <&hwmon0 2 20000>;
+					tach-ch = /bits/ 8 <0x0e>;
+				};
+			};
+
 			pwm at 2f{
 				compatible = "maxim,max31790";
 				#address-cells = <1>;
@@ -1393,6 +1470,42 @@ channel at 5 {
 				};
 			};
 
+			hwmon2: hwmon at 21 {
+				compatible = "nuvoton,nct7363";
+				reg = <0x21>;
+				#pwm-cells = <2>;
+
+				fan-3 {
+					pwms = <&hwmon2 2 20000>;
+					tach-ch = /bits/ 8 <0x00>;
+				};
+
+				fan-4 {
+					pwms = <&hwmon2 5 20000>;
+					tach-ch = /bits/ 8 <0x01>;
+				};
+
+				fan-5 {
+					pwms = <&hwmon2 5 20000>;
+					tach-ch = /bits/ 8 <0x02>;
+				};
+
+				fan-0 {
+					pwms = <&hwmon2 0 20000>;
+					tach-ch = /bits/ 8 <0x09>;
+				};
+
+				fan-1 {
+					pwms = <&hwmon2 0 20000>;
+					tach-ch = /bits/ 8 <0x0c>;
+				};
+
+				fan-2 {
+					pwms = <&hwmon2 2 20000>;
+					tach-ch = /bits/ 8 <0x0e>;
+				};
+			};
+
 			gpio at 22{
 				compatible = "ti,tca6424";
 				reg = <0x22>;
@@ -1400,6 +1513,42 @@ gpio at 22{
 				#gpio-cells = <2>;
 			};
 
+			hwmon3: hwmon at 23 {
+				compatible = "nuvoton,nct7363";
+				reg = <0x23>;
+				#pwm-cells = <2>;
+
+				fan-3 {
+					pwms = <&hwmon3 2 20000>;
+					tach-ch = /bits/ 8 <0x00>;
+				};
+
+				fan-4 {
+					pwms = <&hwmon3 5 20000>;
+					tach-ch = /bits/ 8 <0x01>;
+				};
+
+				fan-5 {
+					pwms = <&hwmon3 5 20000>;
+					tach-ch = /bits/ 8 <0x02>;
+				};
+
+				fan-0 {
+					pwms = <&hwmon3 0 20000>;
+					tach-ch = /bits/ 8 <0x09>;
+				};
+
+				fan-1 {
+					pwms = <&hwmon3 0 20000>;
+					tach-ch = /bits/ 8 <0x0c>;
+				};
+
+				fan-2 {
+					pwms = <&hwmon3 2 20000>;
+					tach-ch = /bits/ 8 <0x0e>;
+				};
+			};
+
 			pwm at 2f{
 				compatible = "maxim,max31790";
 				#address-cells = <1>;
@@ -1493,7 +1642,7 @@ temperature-sensor at 1f {
 				reg = <0x1f>;
 			};
 
-			temperature-sensor at 3c {
+			emc1403 at 3c {
 				compatible = "smsc,emc1403";
 				reg = <0x3c>;
 			};
@@ -1514,7 +1663,7 @@ temperature-sensor at 1f {
 				reg = <0x1f>;
 			};
 
-			temperature-sensor at 3c {
+			emc1403 at 3c {
 				compatible = "smsc,emc1403";
 				reg = <0x3c>;
 			};
@@ -1535,7 +1684,7 @@ temperature-sensor at 1f {
 				reg = <0x1f>;
 			};
 
-			temperature-sensor at 3c {
+			emc1403 at 3c {
 				compatible = "smsc,emc1403";
 				reg = <0x3c>;
 			};
@@ -1556,7 +1705,7 @@ temperature-sensor at 1f {
 				reg = <0x1f>;
 			};
 
-			temperature-sensor at 3c {
+			emc1403 at 3c {
 				compatible = "smsc,emc1403";
 				reg = <0x3c>;
 			};
@@ -1569,6 +1718,92 @@ eeprom at 50 {
 	};
 };
 
+&i3c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i3c1_default>;
+	i3c-pp-scl-hi-period-ns = <40>;
+	i3c-pp-scl-lo-period-ns = <40>;
+	i3c-od-scl-hi-period-ns = <380>;
+	i3c-od-scl-lo-period-ns = <620>;
+	sda-tx-hold-ns = <10>;
+
+	mctp-controller;
+	hub at 0x70 {
+		reg = <0x70 0x3c0 0x00700000>;
+		cp0-ldo-en = "enabled";
+		cp1-ldo-en = "enabled";
+		cp0-ldo-volt = "1.2V";
+		cp1-ldo-volt = "1.2V";
+		tp0145-ldo-en = "enabled";
+		tp2367-ldo-en = "enabled";
+		tp0145-ldo-volt = "1.2V";
+		tp2367-ldo-volt = "1.2V";
+		tp0145-pullup = "2k";
+		tp2367-pullup = "2k";
+
+		target-port at 0 {
+			mode = "i3c";
+			pullup = "enabled";
+		};
+		target-port at 1 {
+			mode = "i3c";
+			pullup = "enabled";
+		};
+		target-port at 2 {
+			mode = "i3c";
+			pullup = "enabled";
+		};
+		target-port at 3 {
+			mode = "i3c";
+			pullup = "enabled";
+		};
+	};
+};
+
+&i3c1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i3c2_default>;
+	i3c-pp-scl-hi-period-ns = <40>;
+	i3c-pp-scl-lo-period-ns = <40>;
+	i3c-od-scl-hi-period-ns = <380>;
+	i3c-od-scl-lo-period-ns = <620>;
+	sda-tx-hold-ns = <10>;
+
+	mctp-controller;
+	hub at 0x70 {
+		reg = <0x70 0x3c0 0x00700000>;
+		cp0-ldo-en = "enabled";
+		cp1-ldo-en = "enabled";
+		cp0-ldo-volt = "1.2V";
+		cp1-ldo-volt = "1.2V";
+		tp0145-ldo-en = "enabled";
+		tp2367-ldo-en = "enabled";
+		tp0145-ldo-volt = "1.2V";
+		tp2367-ldo-volt = "1.2V";
+		tp0145-pullup = "2k";
+		tp2367-pullup = "2k";
+
+		target-port at 0 {
+			mode = "i3c";
+			pullup = "enabled";
+		};
+		target-port at 1 {
+			mode = "i3c";
+			pullup = "enabled";
+		};
+		target-port at 2 {
+			mode = "i3c";
+			pullup = "enabled";
+		};
+		target-port at 3 {
+			mode = "i3c";
+			pullup = "enabled";
+		};
+	};
+};
+
 &adc0 {
 	status = "okay";
 	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
@@ -1579,8 +1814,8 @@ &pinctrl_adc4_default &pinctrl_adc5_default
 
 &adc1 {
 	status = "okay";
-	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default>
-			&pinctrl_adc15_default>;
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+	    &pinctrl_adc15_default>;
 };
 
 &ehci0 {
@@ -1595,6 +1830,10 @@ &uhci {
 	status = "okay";
 };
 
+&jtag1 {
+      status = "okay";
+};
+
 &sgpiom0 {
 	status = "okay";
 	ngpios = <128>;
@@ -1701,16 +1940,29 @@ &pinctrl_gpio3_unbiased &pinctrl_gpio4_unbiased
 			"","PRSNT_NIC0_N","","",
 	/*V0-V7*/       "FM_RESBTN_SLOT5_BMC_N","FM_RESBTN_SLOT6_BMC_N",
 			"FM_RESBTN_SLOT7_BMC_N","FM_RESBTN_SLOT8_BMC_N",
-			"","","","",
+			"ALT_SPIDER_INA233_R_N","ALT_SPIDER_TMP75_R_N",
+			"INT_FANBOARD1_IOEXP_N","INT_FANBOARD0_IOEXP_N",
 	/*W0-W7*/       "PRSNT_TPM_BMC_N","PRSNT_OCP_DEBUG_BMC_N","ALT_TEMP_BMC_N","ALT_RTC_BMC_N",
 			"","","","",
-	/*X0-X7*/       "","LT_HSC_SERVER_SLOT6_N","FLT_HSC_SERVER_SLOT7_N","","","",
+	/*X0-X7*/       "","FLT_HSC_SERVER_SLOT6_N","FLT_HSC_SERVER_SLOT7_N","","","",
 			"PWRGD_SLOT5_STBY","PWRGD_SLOT6_STBY",
 	/*Y0-Y7*/       "","","SPI_LOCK_REQ_BMC_N","PWRGD_SLOT7_STBY",
 			"","","EN_NIC2_POWER_BMC_R","",
 	/*Z0-Z7*/       "EN_P5V_USB_CPLD_R","FLT_HSC_SERVER_SLOT5_N",
 			"PWRGD_SLOT8_STBY","","","","","";
 
+	pin_gpio_b0 {
+		gpios = <ASPEED_GPIO(B, 0) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_b2 {
+		gpios = <ASPEED_GPIO(B, 2) GPIO_ACTIVE_HIGH>;
+		input;
+	};
+	pin_gpio_b3 {
+		gpios = <ASPEED_GPIO(B, 3) GPIO_ACTIVE_HIGH>;
+		input;
+	};
 	pin_gpio_b4 {
 		gpios = <ASPEED_GPIO(B, 4) GPIO_ACTIVE_HIGH>;
 		input;
@@ -1719,6 +1971,14 @@ pin_gpio_b5 {
 		gpios = <ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
 		input;
 	};
+	pin_gpio_e0 {
+		gpios = <ASPEED_GPIO(E, 0) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_e1 {
+		gpios = <ASPEED_GPIO(E, 1) GPIO_ACTIVE_LOW>;
+		input;
+	};
 	pin_gpio_f0 {
 		gpios = <ASPEED_GPIO(F, 0) GPIO_ACTIVE_LOW>;
 		input;
@@ -1759,6 +2019,58 @@ pin_gpio_l7 {
 		gpios = <ASPEED_GPIO(L, 7) GPIO_ACTIVE_LOW>;
 		input;
 	};
+	pin_gpio_m3 {
+		gpios = <ASPEED_GPIO(M, 3) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_m4 {
+		gpios = <ASPEED_GPIO(M, 4) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_m5 {
+		gpios = <ASPEED_GPIO(M, 5) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_n0 {
+		gpios = <ASPEED_GPIO(N, 0) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_n1 {
+		gpios = <ASPEED_GPIO(N, 1) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_n2 {
+		gpios = <ASPEED_GPIO(N, 2) GPIO_ACTIVE_LOW>;
+		input;
+		};
+	pin_gpio_n3 {
+		gpios = <ASPEED_GPIO(N, 3) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_p1 {
+		gpios = <ASPEED_GPIO(P, 1) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_q4 {
+		gpios = <ASPEED_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_q5 {
+		gpios = <ASPEED_GPIO(Q, 5) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_q6 {
+		gpios = <ASPEED_GPIO(Q, 6) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_q7 {
+		gpios = <ASPEED_GPIO(Q, 7) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_r1 {
+		gpios = <ASPEED_GPIO(R, 1) GPIO_ACTIVE_LOW>;
+		input;
+	};
 	pin_gpio_s0 {
 		gpios = <ASPEED_GPIO(S, 0) GPIO_ACTIVE_LOW>;
 		input;
@@ -1767,6 +2079,14 @@ pin_gpio_s1 {
 		gpios = <ASPEED_GPIO(S, 1) GPIO_ACTIVE_LOW>;
 		input;
 	};
+	pin_gpio_s5 {
+		gpios = <ASPEED_GPIO(S, 5) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_u5 {
+		gpios = <ASPEED_GPIO(U, 5) GPIO_ACTIVE_LOW>;
+		input;
+	};
 	pin_gpio_v0 {
 		gpios = <ASPEED_GPIO(V, 0) GPIO_ACTIVE_LOW>;
 		input;
@@ -1783,6 +2103,14 @@ pin_gpio_v3 {
 		gpios = <ASPEED_GPIO(V, 3) GPIO_ACTIVE_LOW>;
 		input;
 	};
+	pin_gpio_v6 {
+		gpios = <ASPEED_GPIO(V, 6) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_v7 {
+		gpios = <ASPEED_GPIO(V, 7) GPIO_ACTIVE_LOW>;
+		input;
+	};
 	pin_gpio_w0 {
 		gpios = <ASPEED_GPIO(W, 0) GPIO_ACTIVE_LOW>;
 		input;
@@ -1815,6 +2143,34 @@ pin_gpio_w7 {
 		gpios = <ASPEED_GPIO(W, 7) GPIO_ACTIVE_LOW>;
 		input;
 	};
+	pin_gpio_x1 {
+		gpios = <ASPEED_GPIO(X, 1) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_x2 {
+		gpios = <ASPEED_GPIO(X, 2) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_x6 {
+		gpios = <ASPEED_GPIO(X, 6) GPIO_ACTIVE_HIGH>;
+		input;
+	};
+	pin_gpio_x7 {
+		gpios = <ASPEED_GPIO(X, 7) GPIO_ACTIVE_HIGH>;
+		input;
+	};
+	pin_gpio_y3 {
+		gpios = <ASPEED_GPIO(Y, 3) GPIO_ACTIVE_HIGH>;
+		input;
+	};
+	pin_gpio_z1 {
+		gpios = <ASPEED_GPIO(Z, 1) GPIO_ACTIVE_LOW>;
+		input;
+	};
+	pin_gpio_z2 {
+		gpios = <ASPEED_GPIO(Z, 2) GPIO_ACTIVE_HIGH>;
+		input;
+	};
 	pin_gpio_z3 {
 		gpios = <ASPEED_GPIO(Z, 3) GPIO_ACTIVE_LOW>;
 		input;
-- 
2.25.1

[PATCH v13 29/29] ARM: dts: aspeed: yosemitet4: add RTQ6056 support on 11 (0x41).

[Delphine CC Chiu]

From: Ian-I-Chien <Ian_Chien@wiwynn.com>

---
 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 4090725160f9..d056f6d5ff6e 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -1081,7 +1081,7 @@ power-sensor at 40 {
 	};
 
 	power-sensor at 41 {
-		compatible = "ti,ina233";
+		compatible = "ti,ina233", "richtek,rtq6056";
 		resistor-calibration = /bits/ 16 <0x0a00>;
 		current-lsb= /bits/ 16 <0x0001>;
 		reg = <0x41>;
-- 
2.25.1