Re: [Bluez-users] Problem with Suse 9.0 and BlueZ

Re: [Bluez-users] Problem with Suse 9.0 and BlueZ

[paulo]

Hi Marcel,

Where do i find hcidump? I could not find it installed....

Regards,

Paulo Wollny


-- Original Message --
From: Marcel Holtmann <marcel@holtmann.org>
To: paulo@mail.wollny.com.br
Send: 11:58 AM
Subject: Re: [Bluez-users] Problem with Suse 9.0 and BlueZ

Hi Paulo,

> i'm trying to use BlueZ with Suse 9.0 and am finding following
problems:
> 
> 1 - /dev/rfcomm0 could not be found.  I have tryed mknod
/dev/rfcomm0 c 216 0. Is this right?

this is correct, but the SuSE 9.0 should create these device nodes.

> 2 - Starting the daemons, it get the following message on
/var/log/messages
> 
>  May 10 11:35:07 hirscheberg hcid[15820]: HCI daemon ver 2.3
started
> May 10 11:35:07 hirscheberg hcid[15820]: Starting security manager
0
> May 10 11:35:07 hirscheberg sdpd[15825]: SDPd ver 1.2 started
> May 10 11:35:18 hirscheberg hcid[15820]: pin_code_request
(sba=72:8C:01:72:02:00, dba=E2:59:22:E3:01:00)
> May 10 11:35:18 hirscheberg kernel: Warning: null TTY for (d8:00)
in tty_fasync
> May 10 11:37:32 hirscheberg hcid[15820]: pin_code_request
(sba=72:8C:01:72:02:00, dba=E2:59:22:E3:01:00)
> May 10 11:37:32 hirscheberg kernel: Warning: null TTY for (d8:00)
in tty_fasync

I don't know where the "null TTY" came from.

> 3 - When trying to contact the phone (a Siemens S55), after havin
/etc/bluetooth/pin PIN:1234 with echo "ATZ" > /dev/rfcomm0
i can not connect to th phone.

Show us "hcidump -x" as root to see what happens.

Regards

Marcel

Re: [Bluez-users] Problem with Suse 9.0 and BlueZ

[Marcel Holtmann]

Hi Paulo,

> Where do i find hcidump? I could not find it installed....

then install it or compile the source from www.bluez.org

Regards

Marcel




-------------------------------------------------------
This SF.Net email is sponsored by Sleepycat Software
Learn developer strategies Cisco, Motorola, Ericsson & Lucent use to deliver
higher performing products faster, at low TCO.
http://www.sleepycat.com/telcomwpreg.php?From=osdnemail3
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users

[Bluez-users] Problem with Suse 9.0 and BlueZ

[paulo]

Hi all,

i'm trying to use BlueZ with Suse 9.0 and am finding following problems:

1 - /dev/rfcomm0 could not be found.  I have tryed mknod /dev/rfcomm0 c 216 0. Is this right?

2 - Starting the daemons, it get the following message on /var/log/messages

 May 10 11:35:07 hirscheberg hcid[15820]: HCI daemon ver 2.3 started
May 10 11:35:07 hirscheberg hcid[15820]: Starting security manager 0
May 10 11:35:07 hirscheberg sdpd[15825]: SDPd ver 1.2 started
May 10 11:35:18 hirscheberg hcid[15820]: pin_code_request (sba=72:8C:01:72:02:00, dba=E2:59:22:E3:01:00)
May 10 11:35:18 hirscheberg kernel: Warning: null TTY for (d8:00) in tty_fasync
May 10 11:37:32 hirscheberg hcid[15820]: pin_code_request (sba=72:8C:01:72:02:00, dba=E2:59:22:E3:01:00)
May 10 11:37:32 hirscheberg kernel: Warning: null TTY for (d8:00) in tty_fasync

3 - When trying to contact the phone (a Siemens S55), after havin /etc/bluetooth/pin PIN:1234 with echo "ATZ" > /dev/rfcomm0 i can not connect to th phone.

Any help is welcome. 

Best regards,

Paulo Wollny






-------------------------------------------------------
This SF.Net email is sponsored by Sleepycat Software
Learn developer strategies Cisco, Motorola, Ericsson & Lucent use to deliver
higher performing products faster, at low TCO.
http://www.sleepycat.com/telcomwpreg.php?From=osdnemail3
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users

Re: [Bluez-users] Problem with Suse 9.0 and BlueZ

[Marcel Holtmann]

Hi Paulo,

> i'm trying to use BlueZ with Suse 9.0 and am finding following problems:
> 
> 1 - /dev/rfcomm0 could not be found.  I have tryed mknod /dev/rfcomm0 c 216 0. Is this right?

this is correct, but the SuSE 9.0 should create these device nodes.

> 2 - Starting the daemons, it get the following message on /var/log/messages
> 
>  May 10 11:35:07 hirscheberg hcid[15820]: HCI daemon ver 2.3 started
> May 10 11:35:07 hirscheberg hcid[15820]: Starting security manager 0
> May 10 11:35:07 hirscheberg sdpd[15825]: SDPd ver 1.2 started
> May 10 11:35:18 hirscheberg hcid[15820]: pin_code_request (sba=72:8C:01:72:02:00, dba=E2:59:22:E3:01:00)
> May 10 11:35:18 hirscheberg kernel: Warning: null TTY for (d8:00) in tty_fasync
> May 10 11:37:32 hirscheberg hcid[15820]: pin_code_request (sba=72:8C:01:72:02:00, dba=E2:59:22:E3:01:00)
> May 10 11:37:32 hirscheberg kernel: Warning: null TTY for (d8:00) in tty_fasync

I don't know where the "null TTY" came from.

> 3 - When trying to contact the phone (a Siemens S55), after havin /etc/bluetooth/pin PIN:1234 with echo "ATZ" > /dev/rfcomm0 i can not connect to th phone.

Show us "hcidump -x" as root to see what happens.

Regards

Marcel




-------------------------------------------------------
This SF.Net email is sponsored by Sleepycat Software
Learn developer strategies Cisco, Motorola, Ericsson & Lucent use to deliver
higher performing products faster, at low TCO.
http://www.sleepycat.com/telcomwpreg.php?From=osdnemail3
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users

Re: [Bluez-users] Problem with Suse 9.0 and BlueZ

[Marcel Holtmann]

Hi Paulo,

> i installed hcidump, and did:
> rfcomm bind 0 00:01:E3:22:59:E2
> echo "ATZ" >  /dev/rfcomm0
>=20
> the result was:
> paulo@hirscheberg:~> echo "ATZ" > /dev/rfcomm0
> bash: /dev/rfcomm0: Die Verbindung wurde vom Kommunikationspartner=20
> zur=FCckgesetzt
> After giving in on the phone the pin number stored in /etc/bluetooth/pi=
n
>=20
> The output of hcidump -x for the above was:
>=20
> hirscheberg:~ # /etc/rc.d/bluetooth restart
> Shutting down=20
> bluetooth                                                              =
done
> Starting bluetooth ...(hci_usb hci_uart=20
> )                                            done
> hirscheberg:~ # hcidump -x
> HCIDump - HCI packet analyzer ver 1.8
> device: hci0 snap_len: 1028 filter: 0xffffffff
> < HCI Command: Create Connection(0x01|0x0005) plen 13
>   E2 59 22 E3 01 00 18 CC 01 00 00 00 01
>  > HCI Event: Command Status(0x0f) plen 4
>   00 01 05 04
>  > HCI Event: Connect Complete(0x03) plen 11
>   00 28 00 E2 59 22 E3 01 00 01 00
> < ACL data: handle 0x0028 flags 0x02 dlen 12
>     L2CAP(s): Connect req: psm 3 scid 0x0040
> < HCI Command: Write Link Policy Settings(0x02|0x000d) plen 4
>   28 00 0E 00
>  > HCI Event: Number of Completed Packets(0x13) plen 5
>   01 28 00 01 00
>  > HCI Event: Command Complete(0x0e) plen 6
>   01 0D 08 00 28 00
>  > HCI Event: Max Slots Change(0x1b) plen 3
>   28 00 05
>  > ACL data: handle 0x0028 flags 0x02 dlen 16
>     L2CAP(s): Connect rsp: dcid 0x0040 scid 0x0040 result 0 status 0
> < ACL data: handle 0x0028 flags 0x02 dlen 16
>     L2CAP(s): Config req: dcid 0x0040 flags 0x0000 clen 4
>     MTU 1024
>  > HCI Event: Number of Completed Packets(0x13) plen 5
>   01 28 00 01 00
>  > ACL data: handle 0x0028 flags 0x02 dlen 18
>     L2CAP(s): Config rsp: scid 0x0040 flags 0x0000 result 0 clen 4
>     MTU 1024
>  > ACL data: handle 0x0028 flags 0x02 dlen 16
>     L2CAP(s): Config req: dcid 0x0040 flags 0x0000 clen 4
>     MTU 339
> < ACL data: handle 0x0028 flags 0x02 dlen 14
>     L2CAP(s): Config rsp: scid 0x0040 flags 0x0000 result 0 clen 0
> < ACL data: handle 0x0028 flags 0x02 dlen 8
>     L2CAP(d): cid 0x40 len 4 [psm 3]
>       RFCOMM(s): SABM: cr 1 dlci 0 pf 1 ilen 0 fcs 0x1c
>  > HCI Event: Number of Completed Packets(0x13) plen 5
>   01 28 00 01 00
>  > HCI Event: Number of Completed Packets(0x13) plen 5
>   01 28 00 01 00
>  > ACL data: handle 0x0028 flags 0x02 dlen 8
>     L2CAP(d): cid 0x40 len 4 [psm 3]
>       RFCOMM(s): UA: cr 1 dlci 0 pf 1 ilen 0 fcs 0xd7
> < ACL data: handle 0x0028 flags 0x02 dlen 18
>     L2CAP(d): cid 0x40 len 14 [psm 3]
>       RFCOMM(s): PN CMD: cr 1 dlci 0 pf 0 ilen 10 fcs 0x70 mcc_len 8
>       dlci 2 frame_type 0 credit_flow 15 pri 7 ack_timer 0 frame_size=20
> 334 max_retrans 0 credits 7
>  > HCI Event: Number of Completed Packets(0x13) plen 5
>   01 28 00 01 00
>  > ACL data: handle 0x0028 flags 0x02 dlen 17
>  > ACL data: handle 0x0028 flags 0x01 dlen 1
>     L2CAP(d): cid 0x40 len 14 [psm 3]
>       RFCOMM(s): PN RSP: cr 0 dlci 0 pf 0 ilen 10 fcs 0xaa mcc_len 8
>       dlci 2 frame_type 0 credit_flow 14 pri 0 ack_timer 0 frame_size=20
> 334 max_retrans 0 credits 2
> < ACL data: handle 0x0028 flags 0x02 dlen 8
>     L2CAP(d): cid 0x40 len 4 [psm 3]
>       RFCOMM(s): SABM: cr 1 dlci 2 pf 1 ilen 0 fcs 0x59
>  > HCI Event: Number of Completed Packets(0x13) plen 5
>   01 28 00 01 00
>  > HCI Event: PIN Code Request(0x16) plen 6
>   E2 59 22 E3 01 00
> < HCI Command: PIN Code Request Negative Reply(0x01|0x000e) plen 6
>   E2 59 22 E3 01 00

this is a PIN helper problem. Look at the mailing list archive to solve
your problem.

Regards

Marcel




-------------------------------------------------------
This SF.Net email is sponsored by Sleepycat Software
Learn developer strategies Cisco, Motorola, Ericsson & Lucent use to deliver
higher performing products faster, at low TCO.
http://www.sleepycat.com/telcomwpreg.php?From=osdnemail3
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users