[Bluez-devel] hello

[Bluez-devel] hello

[Nick]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Hi,

I´m new to the list, my names nick and I´m from Bielefeld, Germany.

I´m still experimenting with my usb-dongle from acer

lsusb: Bus 003 Device 002: ID 0a12:0001 Cambridge Silicon Radio, Ltd
Bluetooth Dongle

and try to get it work with my logitech bluetooth headset via btsco
and the snd-bt-sco module.

Versions:

kernel: 2.6.9-gentoo-r6
bluez-framework: gentoo-unstable
btsco: btsco-cvs 28.11

everything works fine, bluetooth started alsasound started /dev/dsp1
is there, i can connect to my headset via btsco and it gives me
something likes this:

Device is 1:0
Voice setting: 0x0060
RFCOMM channel 1 connected
recieved AT+CKPD=200
opened hwdep
connected SCO channel
Setting sco fd
Done setting sco fd
recieved AT+VGS=11
Sending up speaker change 11
recieved AT+VGS=12
Sending up speaker change 12
recieved AT+VGS=13
Sending up speaker change 13

so, i can change the volume with the buttons on the headset, also i
hear some "noise" after connecting to the SCO channel with the
,multifunktional button on the headset.

my problem is:

i can´t get sound over the device. something dirty like:

cat foobar.file > /dev/dsp1

does nothing, until i cancel it with ctrl+c, also xmms (when
configured for hw:1 alsa with BT) just waits and does nothing.

my normal soundcard is a:

0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801DB AC'97
Audio (rev 03) snd-i8x0

any suggestions?

~ ,nick

PS: obex file transfer and push to my t68i works, so the sdp-server is
running.


-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.6 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org

iD8DBQFBqoEX40bmwXROfRURAuVXAJ0cZxrqMyfSSICtNrdHOtUfVM0PbQCeL3s5
WpaVoCy8SquEFdrzzJo15po=
=qxSd
-----END PGP SIGNATURE-----



-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now. 
http://productguide.itmanagersjournal.com/
_______________________________________________
Bluez-devel mailing list
Bluez-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-devel

Re: [Bluez-devel] hello

[Marcel Holtmann]

Hi Nick,

> I=B4m still experimenting with my usb-dongle from acer
>=20
> lsusb: Bus 003 Device 002: ID 0a12:0001 Cambridge Silicon Radio, Ltd
> Bluetooth Dongle
>=20
> and try to get it work with my logitech bluetooth headset via btsco
> and the snd-bt-sco module.

check with "hciconfig hci0 revision" (as root) for the setting of the
SCO routing. I think it is set to PCM.

Regards

Marcel




-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now. 
http://productguide.itmanagersjournal.com/
_______________________________________________
Bluez-devel mailing list
Bluez-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-devel

Re: [Bluez-devel] hello

[Nick]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1


|
| check with "hciconfig hci0 revision" (as root) for the setting of
| the SCO routing. I think it is set to PCM.

you were right:

(0:1)root@Muramasa:~$ hciconfig hci0 revision
hci0:   Type: USB
~        BD Address: 00:60:57:02:95:FE ACL MTU: 192:8  SCO MTU: 64:8
~        HCI 12.7
~        Chip version: BlueCore01b
~        SCO mapping:  PCM

so, is that the way it should be?


~    ,nick

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.6 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org

iD8DBQFBqxgE40bmwXROfRURAvqRAKDsXeO6wiHySifzPpDzAh8sIOBT6ACeJELH
cVbkAU1OiN0vPgXBjvcpzpg=
=lamt
-----END PGP SIGNATURE-----



-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now. 
http://productguide.itmanagersjournal.com/
_______________________________________________
Bluez-devel mailing list
Bluez-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-devel

Re: [Bluez-devel] hello

[Marcel Holtmann]

Hi Nick,

> | check with "hciconfig hci0 revision" (as root) for the setting of
> | the SCO routing. I think it is set to PCM.
> 
> you were right:
> 
> (0:1)root@Muramasa:~$ hciconfig hci0 revision
> hci0:   Type: USB
> ~        BD Address: 00:60:57:02:95:FE ACL MTU: 192:8  SCO MTU: 64:8
> ~        HCI 12.7
> ~        Chip version: BlueCore01b
> ~        SCO mapping:  PCM
> 
> so, is that the way it should be?

to use your dongle with a headset it must be set to HCI. This value is
stored in the PS keys and it is changeable, but there exists no free
tool for this job.

Regards

Marcel




-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now. 
http://productguide.itmanagersjournal.com/
_______________________________________________
Bluez-devel mailing list
Bluez-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-devel

Re: [Bluez-devel] hello

[Simon Vogl]

well there is one tool:
get the csr reset utility, it contains source code to also alter the hci=20
mapping (which I used on my vaio):
http://www.soft.uni-linz.ac.at/_wiki/tiki-index.php?page=3DProjectBluezHa=
ndsfree
no guarantees given, no questions asked ;)
simon

Marcel Holtmann wrote:

>Hi Nick,
>
> =20
>
>>| check with "hciconfig hci0 revision" (as root) for the setting of
>>| the SCO routing. I think it is set to PCM.
>>
>>you were right:
>>
>>(0:1)root@Muramasa:~$ hciconfig hci0 revision
>>hci0:   Type: USB
>>~        BD Address: 00:60:57:02:95:FE ACL MTU: 192:8  SCO MTU: 64:8
>>~        HCI 12.7
>>~        Chip version: BlueCore01b
>>~        SCO mapping:  PCM
>>
>>so, is that the way it should be?
>>   =20
>>
>
>to use your dongle with a headset it must be set to HCI. This value is
>stored in the PS keys and it is changeable, but there exists no free
>tool for this job.
>
>Regards
>
>Marcel
>
>
>
>
>-------------------------------------------------------
>SF email is sponsored by - The IT Product Guide
>Read honest & candid reviews on hundreds of IT Products from real users.
>Discover which products truly live up to the hype. Start reading now.=20
>http://productguide.itmanagersjournal.com/
>_______________________________________________
>Bluez-devel mailing list
>Bluez-devel@lists.sourceforge.net
>https://lists.sourceforge.net/lists/listinfo/bluez-devel
> =20
>


--=20
_______________________________________________________________________
Dr. Simon Vogl
Institut f=FCr Pervasive Computing, Johannes Kepler Universit=E4t Linz =20
Altenberger Stra=DFe 69, A-4040 Linz, Austria =20
 =20
Tel: +43 732 2468-8517, Fax: +43 732 2468-8426 =20
mailto: vogl@soft.uni-linz.ac.at,  http://www.soft.uni-linz.ac.at/








-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now. 
http://productguide.itmanagersjournal.com/
_______________________________________________
Bluez-devel mailing list
Bluez-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-devel

Re: [Bluez-devel] hello

[Simon Vogl]

no,
these extensions are csr-specific (but they are well documented) -- they=20
use extended
hci commands to access the configuration registers of the bt dongle.
simon

Nick wrote:

> -----BEGIN PGP SIGNED MESSAGE-----
> Hash: SHA1
>
> Simon Vogl wrote:
>
> | well there is one tool: get the csr reset utility, it contains
> | source code to also alter the hci mapping (which I used on my
> | vaio):
> |
> http://www.soft.uni-linz.ac.at/_wiki/tiki-index.php?page=3DProjectBluez=
Handsfree=20
>
> |
> |
> | no guarantees given, no questions asked ;) simon
>
> excellent it works. that was easy. i think i=B4ll take a look at the
> source code, to know what the tool is doing. ;)
>
> is this a vaio specific thing, got a vaio v505cp myself.
>
>
> ~         ,nick
> -----BEGIN PGP SIGNATURE-----
> Version: GnuPG v1.2.6 (GNU/Linux)
> Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org
>
> iD8DBQFBq0ac40bmwXROfRURApRaAKC4H9Bl5g0Y4bSd1UIjpi6s/C+d1wCbBbqu
> fQ2ottOEke4GmhOsowxbZvk=3D
> =3DEh5o
> -----END PGP SIGNATURE-----
>
>
>
> -------------------------------------------------------
> SF email is sponsored by - The IT Product Guide
> Read honest & candid reviews on hundreds of IT Products from real users.
> Discover which products truly live up to the hype. Start reading now.=20
> http://productguide.itmanagersjournal.com/
> _______________________________________________
> Bluez-devel mailing list
> Bluez-devel@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/bluez-devel



--=20
_______________________________________________________________________
Dr. Simon Vogl
Institut f=FCr Pervasive Computing, Johannes Kepler Universit=E4t Linz =20
Altenberger Stra=DFe 69, A-4040 Linz, Austria =20
 =20
Tel: +43 732 2468-8517, Fax: +43 732 2468-8426 =20
mailto: vogl@soft.uni-linz.ac.at,  http://www.soft.uni-linz.ac.at/








-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now. 
http://productguide.itmanagersjournal.com/
_______________________________________________
Bluez-devel mailing list
Bluez-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-devel

Re: [Bluez-devel] hello

[Nick]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Simon Vogl wrote:

| well there is one tool: get the csr reset utility, it contains
| source code to also alter the hci mapping (which I used on my
| vaio):
|
http://www.soft.uni-linz.ac.at/_wiki/tiki-index.php?page=ProjectBluezHandsfree
|
|
| no guarantees given, no questions asked ;) simon

excellent it works. that was easy. i think i´ll take a look at the
source code, to know what the tool is doing. ;)

is this a vaio specific thing, got a vaio v505cp myself.


~         ,nick
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.6 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org

iD8DBQFBq0ac40bmwXROfRURApRaAKC4H9Bl5g0Y4bSd1UIjpi6s/C+d1wCbBbqu
fQ2ottOEke4GmhOsowxbZvk=
=Eh5o
-----END PGP SIGNATURE-----



-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now. 
http://productguide.itmanagersjournal.com/
_______________________________________________
Bluez-devel mailing list
Bluez-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-devel