* [Bluez-users] Problem connecting to NAP via serial null modem connection
2005-04-02 14:54 [Bluez-users] OSX and Bluez PAND/DUND Auth problem Gary Albelli
@ 2005-04-03 16:15 ` Gary Albelli
0 siblings, 0 replies; 2+ messages in thread
From: Gary Albelli @ 2005-04-03 16:15 UTC (permalink / raw)
To: Gary Albelli; +Cc: bluez-users
I have tried to connect from both by laptop and my Palm-pilot. Each
device generates the same log information on the Linux box(NAP). I am
not sure where this is failing or what too do next. Any suggestions on
what I can check or do to diagnose the problem would be greatly
appreciated.
I have included the dmesg output, log output generated from making the
connection, and my hcid.conf file.
Thanks
Gary
===================== tailed from /var/log/messages ==================
Apr 3 11:53:46 darthvader pppd[14136]: pppd 2.4.2 started by root, uid
0
Apr 3 11:53:46 darthvader pppd[14136]: Serial connection established.
Apr 3 11:53:46 darthvader pppd[14136]: Using interface ppp0
Apr 3 11:53:46 darthvader pppd[14136]: Connect: ppp0 <--> /dev/rfcomm0
Apr 3 11:53:46 darthvader dund[14122]: New connection from
00:07:E0:34:9B:13
Apr 3 11:53:51 darthvader pam_timestamp_check: pam_timestamp: `/'
owner UID != 0
====================== DMESG OUTPUT ==========================
[root@darthvader ~]# dmesg
Linux version 2.6.8-1.541 (bhcompile@porky.build.redhat.com) (gcc
version 3.4.1 20040831 (Red Hat 3.4.1-10)) #1 Wed Sep 1 18:01:20 EDT
2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ff77000 (usable)
BIOS-e820: 000000003ff77000 - 000000003ff79000 (ACPI NVS)
BIOS-e820: 000000003ff79000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
1023MB LOWMEM available.
zapping low mappings.
On node 0 totalpages: 262007
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 257911 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 DELL ) @
0x000fd550
ACPI: RSDT (v001 DELL 8200 0x00000008 ASL 0x00000061) @
0x000fd564
ACPI: FADT (v001 DELL 8200 0x00000008 ASL 0x00000061) @
0x000fd598
ACPI: SSDT (v001 DELL st_ex 0x00001000 MSFT 0x0100000d) @
0xfffe5d92
ACPI: MADT (v001 DELL 8200 0x00000008 ASL 0x00000061) @
0x000fd60c
ACPI: BOOT (v001 DELL 8200 0x00000008 ASL 0x00000061) @
0x000fd678
ACPI: DSDT (v001 DELL dt_ex 0x00001000 MSFT 0x0100000d) @
0x00000000
ACPI: PM-Timer IO Port: 0x808
Built 1 zonelists
Kernel command line: ro root=LABEL=/
mapped 4G/4G trampoline to ffff4000.
Initializing CPU#0
CPU 0 irqstacks, hard=023c6000 soft=023c5000
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 2254.557 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 131072 (order: 7, 524288 bytes)
Memory: 1033872k/1048028k available (2024k kernel code, 13476k
reserved, 631k data, 144k init, 0k highmem)
Calibrating delay loop... 4440.06 BogoMIPS (lpj=2220032)
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
There is already a security framework initialized, register_security
failed.
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: 3febfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: 3febf3ff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU: Intel(R) Pentium(R) 4 CPU 2.26GHz stepping 04
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: IRQ9 SCI: Level Trigger.
checking if image is initramfs... it is
Freeing initrd memory: 386k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfbe9e, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040715
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
get_random_bytes called before random driver initialization
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *3 4 5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1f.2[D] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 9
ACPI: PCI interrupt 0000:00:1f.4[C] -> GSI 9 (level, low) -> IRQ 9
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 3
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 3 (level, low) -> IRQ 3
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 3 (level, low) -> IRQ 3
ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 11 (level, low) -> IRQ 11
get_random_bytes called before random driver initialization
vesafb: probe of vesafb0 failed with error -6
Simple Boot Flag at 0x7a set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1112475725.987:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key EB180CB126A51024
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU0] (supports C1)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel i850 Chipset.
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 128M @ 0xe8000000
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
ICH2: IDE controller at PCI slot 0000:00:1f.1
ICH2: chipset revision 4
ICH2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: WDC WD800JB-00CRA1, ATA DISK drive
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: _NEC CD-RW NR-7900A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63,
UDMA(100)
hda: cache flushes not supported
hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 > hda3
hdc: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 37449)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S3 S4 S5)
ACPI wakeup devices:
VBTN PCI0 USB0 USB1 PCI1 KBD
Freeing unused kernel memory: 144k freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
inserting floppy driver for 2.6.8-1.541
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 3 (level, low) -> IRQ 3
divert: allocating divert_blk for eth0
eth0: RealTek RTL8139 at 0xec00, 00:c0:a8:80:fc:3e, IRQ 3
eth0: Identified 8139 chip type 'RTL-8139C'
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1f.2[D] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1f.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: irq 11, io base 0000ff80
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1f.4[C] -> GSI 9 (level, low) -> IRQ 9
uhci_hcd 0000:00:1f.4: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: irq 9, io base 0000ff60
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
usb 2-2: new full speed USB device using address 2
Bluetooth: Core ver 2.6
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: HCI USB driver ver 2.7
usbcore: registered new driver hci_usb
ACPI: Power Button (FF) [PWRF]
EXT3 FS on hda3, internal journal
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1076000k swap on /dev/hda5. Priority:-1 extents:1
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Bluetooth: L2CAP ver 2.3
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.3
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
i2c /dev entries driver
NET: Registered protocol family 10
Disabled Privacy Extensions on device 02359760(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
ip_tables: (C) 2000-2002 Netfilter core team
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
eth0: no IPv6 routers present
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
Bluetooth: BNEP (Ethernet Emulation) ver 1.2
Bluetooth: BNEP filters: protocol multicast
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
divert: not allocating divert_blk for non-ethernet device ppp0
PPP Deflate Compression module registered
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
===================== hcid.conf ===================================
#
# HCI daemon configuration file.
#
# $Id: hcid.conf,v 1.4 2004/04/29 20:14:21 holtmann Exp $
#
# HCId options
options {
# Automatically initialize new devices
autoinit yes;
# Security Manager mode
# none - Security manager disabled
# auto - Use local PIN for incoming connections
# user - Always ask user for a PIN
#
security auto;
# Pairing mode
# none - Pairing disabled
# multi - Allow pairing with already paired devices
# once - Pair once and deny successive attempts
pairing multi;
# PIN helper
pin_helper /usr/bin/bluepin;
# D-Bus PIN helper
#dbus_pin_helper;
}
# Default settings for HCI devices
device {
# Local device name
# %d - device id
# %h - host name
name "%h-%d";
# Local device class
class 0x120104;
# Default packet type
#pkt_type DH1,DM1,HV1;
# Inquiry and Page scan
iscan enable; pscan enable;
# Default link mode
# none - no specific policy
# accept - always accept incoming connections
# master - become master on incoming connections,
# deny role switch on outgoing connections
#
#lm accept,master;
#
lm accept;
# Default link policy
# none - no specific policy
# rswitch - allow role switch
# hold - allow hold mode
# sniff - allow sniff mode
# park - allow park mode
#
#lp hold,sniff;
#
lp rswitch,hold,sniff,park;
# Authentication and Encryption
auth disable;
encrypt disable;
}
On Apr 2, 2005, at 9:54 AM, Gary Albelli wrote:
> I have creates a Bluetooth serial connection on OSX. I am trying to
> connect to a BlueZ NAP on a Fedora linux box. It appears to connect, i
> see this in the log on the Linux box, but the OSX client shows
> "Authenticating" but never does.
>
>
-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now.
http://ads.osdn.com/?ad_id=6595&alloc_id=14396&op=click
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users
^ permalink raw reply [flat|nested] 2+ messages in thread
* [Bluez-users] Problem connecting to NAP via serial null modem connection
@ 2005-04-03 16:21 Gary Albelli
0 siblings, 0 replies; 2+ messages in thread
From: Gary Albelli @ 2005-04-03 16:21 UTC (permalink / raw)
To: bluez-users
[-- Attachment #1: Type: text/plain, Size: 17383 bytes --]
Begin forwarded message:
> From: Gary Albelli <galbelli@optonline.net>
> Date: April 3, 2005 12:15:14 PM EDT
> To: Gary Albelli <galbelli@optonline.net>
> Cc: bluez-users@lists.sourceforge.net
> Subject: Problem connecting to NAP via serial null modem connection
>
> I have tried to connect from both by laptop and my Palm-pilot. Each
> device generates the same log information on the Linux box(NAP). I am
> not sure where this is failing or what too do next. Any suggestions on
> what I can check or do to diagnose the problem would be greatly
> appreciated.
>
> I have included the dmesg output, log output generated from making the
> connection, and my hcid.conf file.
>
> Thanks
> Gary
>
> ===================== tailed from /var/log/messages ==================
>
> Apr 3 11:53:46 darthvader pppd[14136]: pppd 2.4.2 started by root,
> uid 0
> Apr 3 11:53:46 darthvader pppd[14136]: Serial connection established.
> Apr 3 11:53:46 darthvader pppd[14136]: Using interface ppp0
> Apr 3 11:53:46 darthvader pppd[14136]: Connect: ppp0 <--> /dev/rfcomm0
> Apr 3 11:53:46 darthvader dund[14122]: New connection from
> 00:07:E0:34:9B:13
> Apr 3 11:53:51 darthvader pam_timestamp_check: pam_timestamp: `/'
> owner UID != 0
>
>
>
>
> ====================== DMESG OUTPUT ==========================
>
> [root@darthvader ~]# dmesg
> Linux version 2.6.8-1.541 (bhcompile@porky.build.redhat.com) (gcc
> version 3.4.1 20040831 (Red Hat 3.4.1-10)) #1 Wed Sep 1 18:01:20 EDT
> 2004
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000003ff77000 (usable)
> BIOS-e820: 000000003ff77000 - 000000003ff79000 (ACPI NVS)
> BIOS-e820: 000000003ff79000 - 0000000040000000 (reserved)
> BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
> BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
> 0MB HIGHMEM available.
> 1023MB LOWMEM available.
> zapping low mappings.
> On node 0 totalpages: 262007
> DMA zone: 4096 pages, LIFO batch:1
> Normal zone: 257911 pages, LIFO batch:16
> HighMem zone: 0 pages, LIFO batch:1
> DMI 2.3 present.
> ACPI: RSDP (v000 DELL ) @
> 0x000fd550
> ACPI: RSDT (v001 DELL 8200 0x00000008 ASL 0x00000061) @
> 0x000fd564
> ACPI: FADT (v001 DELL 8200 0x00000008 ASL 0x00000061) @
> 0x000fd598
> ACPI: SSDT (v001 DELL st_ex 0x00001000 MSFT 0x0100000d) @
> 0xfffe5d92
> ACPI: MADT (v001 DELL 8200 0x00000008 ASL 0x00000061) @
> 0x000fd60c
> ACPI: BOOT (v001 DELL 8200 0x00000008 ASL 0x00000061) @
> 0x000fd678
> ACPI: DSDT (v001 DELL dt_ex 0x00001000 MSFT 0x0100000d) @
> 0x00000000
> ACPI: PM-Timer IO Port: 0x808
> Built 1 zonelists
> Kernel command line: ro root=LABEL=/
> mapped 4G/4G trampoline to ffff4000.
> Initializing CPU#0
> CPU 0 irqstacks, hard=023c6000 soft=023c5000
> PID hash table entries: 4096 (order 12: 32768 bytes)
> Detected 2254.557 MHz processor.
> Using tsc for high-res timesource
> Console: colour VGA+ 80x25
> Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes)
> Inode-cache hash table entries: 131072 (order: 7, 524288 bytes)
> Memory: 1033872k/1048028k available (2024k kernel code, 13476k
> reserved, 631k data, 144k init, 0k highmem)
> Calibrating delay loop... 4440.06 BogoMIPS (lpj=2220032)
> Security Scaffold v1.0.0 initialized
> SELinux: Initializing.
> SELinux: Starting in permissive mode
> There is already a security framework initialized, register_security
> failed.
> selinux_register_security: Registering secondary module capability
> Capability LSM initialized as secondary
> Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
> CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000
> CPU: After vendor identify, caps: 3febfbff 00000000 00000000 00000000
> CPU: Trace cache: 12K uops, L1 D cache: 8K
> CPU: L2 cache: 512K
> CPU: After all inits, caps: 3febf3ff 00000000 00000000 00000080
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
> CPU: Intel(R) Pentium(R) 4 CPU 2.26GHz stepping 04
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Checking 'hlt' instruction... OK.
> ACPI: IRQ9 SCI: Level Trigger.
> checking if image is initramfs... it is
> Freeing initrd memory: 386k freed
> NET: Registered protocol family 16
> PCI: PCI BIOS revision 2.10 entry at 0xfbe9e, last bus=2
> PCI: Using configuration type 1
> mtrr: v2.0 (20020519)
> ACPI: Subsystem revision 20040715
> ACPI: Interpreter enabled
> ACPI: Using PIC for interrupt routing
> ACPI: PCI Root Bridge [PCI0] (00:00)
> PCI: Probing PCI hardware (bus 00)
> get_random_bytes called before random driver initialization
> PCI: Transparent bridge - 0000:00:1e.0
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
> ACPI: PCI Interrupt Link [LNKA] (IRQs *3 4 5 6 7 9 10 11 12 15)
> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15)
> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 15)
> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 15)
> ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 15) *0,
> disabled.
> ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 15) *0,
> disabled.
> ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 15) *0,
> disabled.
> ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 15)
> Linux Plug and Play Support v0.97 (c) Adam Belay
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> PCI: Using ACPI for IRQ routing
> ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
> ACPI: PCI interrupt 0000:00:1f.2[D] -> GSI 11 (level, low) -> IRQ 11
> ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
> ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 10 (level, low) -> IRQ 10
> ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 9
> ACPI: PCI interrupt 0000:00:1f.4[C] -> GSI 9 (level, low) -> IRQ 9
> ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 3
> ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 3 (level, low) -> IRQ 3
> ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 3 (level, low) -> IRQ 3
> ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 10 (level, low) -> IRQ 10
> ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
> ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 11 (level, low) -> IRQ 11
> get_random_bytes called before random driver initialization
> vesafb: probe of vesafb0 failed with error -6
> Simple Boot Flag at 0x7a set to 0x1
> apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
> apm: overridden by ACPI.
> audit: initializing netlink socket (disabled)
> audit(1112475725.987:0): initialized
> Total HugeTLB memory allocated, 0
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> SELinux: Registering netfilter hooks
> Initializing Cryptographic API
> ksign: Installing public key data
> Loading keyring
> - Added public key EB180CB126A51024
> - User ID: Red Hat, Inc. (Kernel Module GPG key)
> pci_hotplug: PCI Hot Plug PCI Core version: 0.5
> ACPI: Processor [CPU0] (supports C1)
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Real Time Clock Driver v1.12
> Linux agpgart interface v0.100 (c) Dave Jones
> agpgart: Detected an Intel i850 Chipset.
> agpgart: Maximum main memory to use for agp memory: 941M
> agpgart: AGP aperture is 128M @ 0xe8000000
> Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing
> enabled
> ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
> divert: not allocating divert_blk for non-ethernet device lo
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with
> idebus=xx
> ICH2: IDE controller at PCI slot 0000:00:1f.1
> ICH2: chipset revision 4
> ICH2: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
> ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
> Probing IDE interface ide0...
> hda: WDC WD800JB-00CRA1, ATA DISK drive
> Using cfq io scheduler
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> Probing IDE interface ide1...
> hdc: _NEC CD-RW NR-7900A, ATAPI CD/DVD-ROM drive
> ide1 at 0x170-0x177,0x376 on irq 15
> Probing IDE interface ide2...
> ide2: Wait for ready failed before probe !
> Probing IDE interface ide3...
> ide3: Wait for ready failed before probe !
> Probing IDE interface ide4...
> ide4: Wait for ready failed before probe !
> Probing IDE interface ide5...
> ide5: Wait for ready failed before probe !
> hda: max request size: 128KiB
> hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63,
> UDMA(100)
> hda: cache flushes not supported
> hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 > hda3
> hdc: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
> Uniform CD-ROM driver Revision: 3.20
> ide-floppy driver 0.99.newide
> usbcore: registered new driver hiddev
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.0:USB HID core driver
> mice: PS/2 mouse device common for all mice
> serio: i8042 AUX port at 0x60,0x64 irq 12
> input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
> serio: i8042 KBD port at 0x60,0x64 irq 1
> input: AT Translated Set 2 keyboard on isa0060/serio0
> md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
> NET: Registered protocol family 2
> IP: routing cache hash table of 2048 buckets, 64Kbytes
> TCP: Hash tables configured (established 262144 bind 37449)
> Initializing IPsec netlink socket
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> ACPI: (supports S0 S1 S3 S4 S5)
> ACPI wakeup devices:
> VBTN PCI0 USB0 USB1 PCI1 KBD
> Freeing unused kernel memory: 144k freed
> kjournald starting. Commit interval 5 seconds
> EXT3-fs: mounted filesystem with ordered data mode.
> inserting floppy driver for 2.6.8-1.541
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> 8139too Fast Ethernet driver 0.9.27
> ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 3 (level, low) -> IRQ 3
> divert: allocating divert_blk for eth0
> eth0: RealTek RTL8139 at 0xec00, 00:c0:a8:80:fc:3e, IRQ 3
> eth0: Identified 8139 chip type 'RTL-8139C'
> USB Universal Host Controller Interface driver v2.2
> ACPI: PCI interrupt 0000:00:1f.2[D] -> GSI 11 (level, low) -> IRQ 11
> uhci_hcd 0000:00:1f.2: UHCI Host Controller
> PCI: Setting latency timer of device 0000:00:1f.2 to 64
> uhci_hcd 0000:00:1f.2: irq 11, io base 0000ff80
> uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 2 ports detected
> ACPI: PCI interrupt 0000:00:1f.4[C] -> GSI 9 (level, low) -> IRQ 9
> uhci_hcd 0000:00:1f.4: UHCI Host Controller
> PCI: Setting latency timer of device 0000:00:1f.4 to 64
> uhci_hcd 0000:00:1f.4: irq 9, io base 0000ff60
> uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> md: Autodetecting RAID arrays.
> md: autorun ...
> md: ... autorun DONE.
> usb 2-2: new full speed USB device using address 2
> Bluetooth: Core ver 2.6
> NET: Registered protocol family 31
> Bluetooth: HCI device and connection manager initialized
> Bluetooth: HCI socket layer initialized
> Bluetooth: HCI USB driver ver 2.7
> usbcore: registered new driver hci_usb
> ACPI: Power Button (FF) [PWRF]
> EXT3 FS on hda3, internal journal
> device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on hda1, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on hda9, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on hda10, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on hda6, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on hda8, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on hda7, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> Adding 1076000k swap on /dev/hda5. Priority:-1 extents:1
> parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
> parport0: irq 7 detected
> ip_tables: (C) 2000-2002 Netfilter core team
> ip_tables: (C) 2000-2002 Netfilter core team
> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
> Bluetooth: L2CAP ver 2.3
> Bluetooth: L2CAP socket layer initialized
> Bluetooth: RFCOMM ver 1.3
> Bluetooth: RFCOMM socket layer initialized
> Bluetooth: RFCOMM TTY layer initialized
> i2c /dev entries driver
> NET: Registered protocol family 10
> Disabled Privacy Extensions on device 02359760(lo)
> IPv6 over IPv4 tunneling driver
> divert: not allocating divert_blk for non-ethernet device sit0
> ip_tables: (C) 2000-2002 Netfilter core team
> parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
> parport0: irq 7 detected
> lp0: using parport0 (polling).
> lp0: console ready
> eth0: no IPv6 routers present
> ISO 9660 Extensions: Microsoft Joliet Level 3
> ISO 9660 Extensions: RRIP_1991A
> Bluetooth: BNEP (Ethernet Emulation) ver 1.2
> Bluetooth: BNEP filters: protocol multicast
> CSLIP: code copyright 1989 Regents of the University of California
> PPP generic driver version 2.4.2
> divert: not allocating divert_blk for non-ethernet device ppp0
> PPP Deflate Compression module registered
> divert: no divert_blk to free, ppp0 not ethernet
> divert: not allocating divert_blk for non-ethernet device ppp0
> divert: no divert_blk to free, ppp0 not ethernet
> divert: not allocating divert_blk for non-ethernet device ppp0
> divert: no divert_blk to free, ppp0 not ethernet
> divert: not allocating divert_blk for non-ethernet device ppp0
> divert: no divert_blk to free, ppp0 not ethernet
> divert: not allocating divert_blk for non-ethernet device ppp0
> divert: no divert_blk to free, ppp0 not ethernet
> divert: not allocating divert_blk for non-ethernet device ppp0
> divert: no divert_blk to free, ppp0 not ethernet
> divert: not allocating divert_blk for non-ethernet device ppp0
> divert: no divert_blk to free, ppp0 not ethernet
> divert: not allocating divert_blk for non-ethernet device ppp0
> divert: no divert_blk to free, ppp0 not ethernet
> divert: not allocating divert_blk for non-ethernet device ppp0
> divert: no divert_blk to free, ppp0 not ethernet
> divert: not allocating divert_blk for non-ethernet device ppp0
> divert: no divert_blk to free, ppp0 not ethernet
> divert: not allocating divert_blk for non-ethernet device ppp0
>
>
>
>
> ===================== hcid.conf ===================================
>
> #
> # HCI daemon configuration file.
> #
> # $Id: hcid.conf,v 1.4 2004/04/29 20:14:21 holtmann Exp $
> #
>
> # HCId options
> options {
> # Automatically initialize new devices
> autoinit yes;
>
> # Security Manager mode
> # none - Security manager disabled
> # auto - Use local PIN for incoming connections
> # user - Always ask user for a PIN
> #
> security auto;
>
> # Pairing mode
> # none - Pairing disabled
> # multi - Allow pairing with already paired devices
> # once - Pair once and deny successive attempts
> pairing multi;
>
> # PIN helper
> pin_helper /usr/bin/bluepin;
>
> # D-Bus PIN helper
> #dbus_pin_helper;
> }
>
> # Default settings for HCI devices
> device {
> # Local device name
> # %d - device id
> # %h - host name
> name "%h-%d";
>
> # Local device class
> class 0x120104;
>
> # Default packet type
> #pkt_type DH1,DM1,HV1;
>
> # Inquiry and Page scan
> iscan enable; pscan enable;
>
> # Default link mode
> # none - no specific policy
> # accept - always accept incoming connections
> # master - become master on incoming connections,
> # deny role switch on outgoing connections
> #
> #lm accept,master;
> #
> lm accept;
>
> # Default link policy
> # none - no specific policy
> # rswitch - allow role switch
> # hold - allow hold mode
> # sniff - allow sniff mode
> # park - allow park mode
> #
> #lp hold,sniff;
> #
> lp rswitch,hold,sniff,park;
>
> # Authentication and Encryption
> auth disable;
> encrypt disable;
> }
>
>
>
>
>
>
> On Apr 2, 2005, at 9:54 AM, Gary Albelli wrote:
>
>> I have creates a Bluetooth serial connection on OSX. I am trying to
>> connect to a BlueZ NAP on a Fedora linux box. It appears to connect,
>> i see this in the log on the Linux box, but the OSX client shows
>> "Authenticating" but never does.
>>
>>
>
[-- Attachment #2: Type: text/enriched, Size: 17226 bytes --]
Begin forwarded message:
<excerpt><bold><color><param>0000,0000,0000</param>From:
</color></bold>Gary Albelli <<galbelli@optonline.net>
<bold><color><param>0000,0000,0000</param>Date: </color></bold>April
3, 2005 12:15:14 PM EDT
<bold><color><param>0000,0000,0000</param>To: </color></bold>Gary
Albelli <<galbelli@optonline.net>
<bold><color><param>0000,0000,0000</param>Cc:
</color></bold>bluez-users@lists.sourceforge.net
<bold><color><param>0000,0000,0000</param>Subject: </color>Problem
connecting to NAP via serial null modem connection
</bold>
I have tried to connect from both by laptop and my Palm-pilot. Each
device generates the same log information on the Linux box(NAP). I am
not sure where this is failing or what too do next. Any suggestions on
what I can check or do to diagnose the problem would be greatly
appreciated.
I have included the dmesg output, log output generated from making the
connection, and my hcid.conf file.
Thanks
Gary
===================== tailed from /var/log/messages ==================
Apr 3 11:53:46 darthvader pppd[14136]: pppd 2.4.2 started by root,
uid 0
Apr 3 11:53:46 darthvader pppd[14136]: Serial connection established.
Apr 3 11:53:46 darthvader pppd[14136]: Using interface ppp0
Apr 3 11:53:46 darthvader pppd[14136]: Connect: ppp0 <<-->
/dev/rfcomm0
Apr 3 11:53:46 darthvader dund[14122]: New connection from
00:07:E0:34:9B:13
Apr 3 11:53:51 darthvader pam_timestamp_check: pam_timestamp: `/'
owner UID != 0
====================== DMESG OUTPUT ==========================
[root@darthvader ~]# dmesg
Linux version 2.6.8-1.541 (bhcompile@porky.build.redhat.com) (gcc
version 3.4.1 20040831 (Red Hat 3.4.1-10)) #1 Wed Sep 1 18:01:20 EDT
2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ff77000 (usable)
BIOS-e820: 000000003ff77000 - 000000003ff79000 (ACPI NVS)
BIOS-e820: 000000003ff79000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
1023MB LOWMEM available.
zapping low mappings.
On node 0 totalpages: 262007
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 257911 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 DELL ) @
0x000fd550
ACPI: RSDT (v001 DELL 8200 0x00000008 ASL 0x00000061) @
0x000fd564
ACPI: FADT (v001 DELL 8200 0x00000008 ASL 0x00000061) @
0x000fd598
ACPI: SSDT (v001 DELL st_ex 0x00001000 MSFT 0x0100000d) @
0xfffe5d92
ACPI: MADT (v001 DELL 8200 0x00000008 ASL 0x00000061) @
0x000fd60c
ACPI: BOOT (v001 DELL 8200 0x00000008 ASL 0x00000061) @
0x000fd678
ACPI: DSDT (v001 DELL dt_ex 0x00001000 MSFT 0x0100000d) @
0x00000000
ACPI: PM-Timer IO Port: 0x808
Built 1 zonelists
Kernel command line: ro root=LABEL=/
mapped 4G/4G trampoline to ffff4000.
Initializing CPU#0
CPU 0 irqstacks, hard=023c6000 soft=023c5000
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 2254.557 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 131072 (order: 7, 524288 bytes)
Memory: 1033872k/1048028k available (2024k kernel code, 13476k
reserved, 631k data, 144k init, 0k highmem)
Calibrating delay loop... 4440.06 BogoMIPS (lpj=2220032)
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
There is already a security framework initialized, register_security
failed.
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: 3febfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: 3febf3ff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU: Intel(R) Pentium(R) 4 CPU 2.26GHz stepping 04
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: IRQ9 SCI: Level Trigger.
checking if image is initramfs... it is
Freeing initrd memory: 386k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfbe9e, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040715
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
get_random_bytes called before random driver initialization
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *3 4 5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1f.2[D] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 9
ACPI: PCI interrupt 0000:00:1f.4[C] -> GSI 9 (level, low) -> IRQ 9
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 3
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 3 (level, low) -> IRQ 3
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 3 (level, low) -> IRQ 3
ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 11 (level, low) -> IRQ 11
get_random_bytes called before random driver initialization
vesafb: probe of vesafb0 failed with error -6
Simple Boot Flag at 0x7a set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1112475725.987:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key EB180CB126A51024
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU0] (supports C1)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel i850 Chipset.
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 128M @ 0xe8000000
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing
enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
ICH2: IDE controller at PCI slot 0000:00:1f.1
ICH2: chipset revision 4
ICH2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: WDC WD800JB-00CRA1, ATA DISK drive
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: _NEC CD-RW NR-7900A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63,
UDMA(100)
hda: cache flushes not supported
hda: hda1 hda2 << hda5 hda6 hda7 hda8 hda9 hda10 > hda3
hdc: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 37449)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S3 S4 S5)
ACPI wakeup devices:
VBTN PCI0 USB0 USB1 PCI1 KBD
Freeing unused kernel memory: 144k freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
inserting floppy driver for 2.6.8-1.541
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 3 (level, low) -> IRQ 3
divert: allocating divert_blk for eth0
eth0: RealTek RTL8139 at 0xec00, 00:c0:a8:80:fc:3e, IRQ 3
eth0: Identified 8139 chip type 'RTL-8139C'
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1f.2[D] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1f.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: irq 11, io base 0000ff80
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1f.4[C] -> GSI 9 (level, low) -> IRQ 9
uhci_hcd 0000:00:1f.4: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: irq 9, io base 0000ff60
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
usb 2-2: new full speed USB device using address 2
Bluetooth: Core ver 2.6
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: HCI USB driver ver 2.7
usbcore: registered new driver hci_usb
ACPI: Power Button (FF) [PWRF]
EXT3 FS on hda3, internal journal
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1076000k swap on /dev/hda5. Priority:-1 extents:1
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Bluetooth: L2CAP ver 2.3
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.3
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
i2c /dev entries driver
NET: Registered protocol family 10
Disabled Privacy Extensions on device 02359760(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
ip_tables: (C) 2000-2002 Netfilter core team
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
eth0: no IPv6 routers present
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
Bluetooth: BNEP (Ethernet Emulation) ver 1.2
Bluetooth: BNEP filters: protocol multicast
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
divert: not allocating divert_blk for non-ethernet device ppp0
PPP Deflate Compression module registered
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
divert: no divert_blk to free, ppp0 not ethernet
divert: not allocating divert_blk for non-ethernet device ppp0
===================== hcid.conf ===================================
#
# HCI daemon configuration file.
#
# $Id: hcid.conf,v 1.4 2004/04/29 20:14:21 holtmann Exp $
#
# HCId options
options {
# Automatically initialize new devices
autoinit yes;
# Security Manager mode
# none - Security manager disabled
# auto - Use local PIN for incoming connections
# user - Always ask user for a PIN
#
security auto;
# Pairing mode
# none - Pairing disabled
# multi - Allow pairing with already paired devices
# once - Pair once and deny successive attempts
pairing multi;
# PIN helper
pin_helper /usr/bin/bluepin;
# D-Bus PIN helper
#dbus_pin_helper;
}
# Default settings for HCI devices
device {
# Local device name
# %d - device id
# %h - host name
name "%h-%d";
# Local device class
class 0x120104;
# Default packet type
#pkt_type DH1,DM1,HV1;
# Inquiry and Page scan
iscan enable; pscan enable;
# Default link mode
# none - no specific policy
# accept - always accept incoming connections
# master - become master on incoming connections,
# deny role switch on outgoing connections
#
#lm accept,master;
#
lm accept;
# Default link policy
# none - no specific policy
# rswitch - allow role switch
# hold - allow hold mode
# sniff - allow sniff mode
# park - allow park mode
#
#lp hold,sniff;
#
lp rswitch,hold,sniff,park;
# Authentication and Encryption
auth disable;
encrypt disable;
}
On Apr 2, 2005, at 9:54 AM, Gary Albelli wrote:
<excerpt>I have creates a Bluetooth serial connection on OSX. I am
trying to connect to a BlueZ NAP on a Fedora linux box. It appears to
connect, i see this in the log on the Linux box, but the OSX client
shows "Authenticating" but never does.
</excerpt>
</excerpt>
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2005-04-03 16:21 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-04-03 16:21 [Bluez-users] Problem connecting to NAP via serial null modem connection Gary Albelli
-- strict thread matches above, loose matches on Subject: below --
2005-04-02 14:54 [Bluez-users] OSX and Bluez PAND/DUND Auth problem Gary Albelli
2005-04-03 16:15 ` [Bluez-users] Problem connecting to NAP via serial null modem connection Gary Albelli
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox