From: Embedded System <embed.sys@gmail.com>
To: bluez-users@lists.sourceforge.net
Subject: [Bluez-users] Can't init device hci0 (all information included), help! Thanx a lot!!!
Date: Sun, 23 Jan 2005 18:10:50 +0800 [thread overview]
Message-ID: <c93f2a2905012302107465ea43@mail.gmail.com> (raw)
hi, everyone
when I call "hciconfig hci0 up", it prints:
Can't init device hci0: Connection timed out (110)
Working environment is as follows:
1, Vmware workstation 5.0 + Redhat 9.0, with kernel 2.6.8.1, bluez 2.14
2, Bluetooth subsystem enabled
3, Billionton BlueTooth Dongle Class I USBBTC1A
4, "/etc/rc.d/init.d/bluetooth start" already run
Outputs (lspci, lsmod, /proc/bus/usb/devices/,hciconfig, dmesg)
1, output from lspci
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB
2, output from lsmod
Module Size Used by
ehci_hcd 42688 0
hci_usb 13184 0
rfcomm 38712 0
l2cap 24128 3 rfcomm
autofs 15520 0
ohci1394 34912 0
ieee1394 110384 1 ohci1394
parport_pc 25696 0
parport 40672 1 parport_pc
bluetooth 48292 3 hci_usb,rfcomm,l2cap
usbhid 24800 0
uhci_hcd 33160 0
usbcore 127540 6 ehci_hcd,hci_usb,usbhid,uhci_hcd
3, output from /proc/bus/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.8.1 uhci_hcd
S: Product=Intel Corp. 82371AB/EB/MB PIIX4 USB
S: SerialNumber=0000:00:07.2
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(unk. ) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a12 ProdID=0001 Rev= 4.87
C:* #Ifs= 3 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none)
4, output from hciconfig
hci0: Type: USB
BD Address: 00:00:00:00:00:00 ACL MTU: 0:0 SCO MTU: 0:0
DOWN
RX bytes:0 acl:0 sco:0 events:0 errors:0
TX bytes:0 acl:0 sco:0 commands:0 errors:0
Features: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
Packet type: DM1 DH1 HV1
Link policy:
Link mode: SLAVE ACCEPT
8, output from dmesg
uhci_hcd 0000:00:07.2: suspend_hc
uhci_hcd 0000:00:07.2: wakeup_hc
uhci_hcd 0000:00:07.2: port 1 portsc 0083
hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 1-1: new full speed USB device using address 3
usb 1-1: skipped 1 descriptor after interface
usb 1-1: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: hotplug
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: hotplug
hci_usb 1-1:1.0: usb_probe_interface
hci_usb 1-1:1.0: usb_probe_interface - got id
usb 1-1: adding 1-1:1.1 (config #1, interface 1)
usb 1-1:1.1: hotplug
usb 1-1: adding 1-1:1.2 (config #1, interface 2)
usb 1-1:1.2: hotplug
hci_usb 1-1:1.2: usb_probe_interface
hci_usb 1-1:1.2: usb_probe_interface - got id
I really appreciate your kindly help and your time! if you need any
further information
please let me know, thanx again!
Is it a kernel problem? Bluez bug? Configuration Problem? Vmware
Restrictions? or what else?
-andy
-------------------------------------------------------
This SF.Net email is sponsored by: IntelliVIEW -- Interactive Reporting
Tool for open source databases. Create drag-&-drop reports. Save time
by over 75%! Publish reports on the web. Export to DOC, XLS, RTF, etc.
Download a FREE copy at http://www.intelliview.com/go/osdn_nl
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users
next reply other threads:[~2005-01-23 10:10 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-01-23 10:10 Embedded System [this message]
2005-01-23 17:14 ` [Bluez-users] Can't init device hci0 (all information included), help! Thanx a lot!!! Marcel Holtmann
2005-01-24 3:54 ` Embedded System
2005-01-24 8:19 ` Michal Semler
2005-01-24 10:05 ` Embedded System
2005-01-24 12:22 ` Marcel Holtmann
2005-01-25 15:23 ` Embedded System
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=c93f2a2905012302107465ea43@mail.gmail.com \
--to=embed.sys@gmail.com \
--cc=bluez-users@lists.sourceforge.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox