From: Embedded System <embed.sys@gmail.com>
To: bluez-users@lists.sourceforge.net
Subject: Re: [Bluez-users] Can't init device hci0 (all information included), help! Thanx a lot!!!
Date: Mon, 24 Jan 2005 11:54:23 +0800 [thread overview]
Message-ID: <c93f2a2905012319541a6c820f@mail.gmail.com> (raw)
In-Reply-To: <1106500482.9269.46.camel@pegasus>
hi, Marcel
Thanks for the info, but it still doesn't work
I have updated my kernel to 2.6.10-mh2, and with "modprobe hci_usb
isoc=0", but when I plug the usb doggle the first time, screen prints
out :
usb 1-1 : can't set config #1, error -32
usb 1-1 : khubd timed out on ep0in
and I pull out and plug it again, it prints out only the second line as:
usb 1-1 : khubd timed out on ep0in
and the outputs(/proc/bus/usb/devices, lsusb ) as follows:
1, output from /proc/bus/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.10-mh2 uhci_hcd
S: Product=Intel Corp. 82371AB/EB/MB PIIX4 USB
S: SerialNumber=0000:00:07.2
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(unk. ) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a12 ProdID=0001 Rev= 4.87
C:* #Ifs= 3 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none)
2, lsusb output
......
Bus 001 Device 005: ID 0a12:0001 Cambridge Silicon Radio Ltd.
usb 1-1: lsusb timed out on ep0in
usb 1-1: lsusb timed out on ep0in
....
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 224
bDeviceSubClass 1
bDeviceProtocol 1
bMaxPacketSize0 64
idVendor 0x0a12 Cambridge Silicon Radio Ltd.
idProduct 0x0001
bcdDevice 4.87
iManufacturer 0
iProduct 0
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 193
bNumInterfaces 3
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 224
bInterfaceSubClass 1
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type none
wMaxPacketSize 16
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type none
wMaxPacketSize 64
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type none
wMaxPacketSize 64
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 224
bInterfaceSubClass 1
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 0
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 0
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 1
bNumEndpoints 2
bInterfaceClass 224
bInterfaceSubClass 1
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 9
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 9
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 2
bNumEndpoints 2
bInterfaceClass 224
bInterfaceSubClass 1
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 17
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 17
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 3
bNumEndpoints 2
bInterfaceClass 224
bInterfaceSubClass 1
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 25
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 25
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 4
bNumEndpoints 2
bInterfaceClass 224
bInterfaceSubClass 1
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 33
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 33
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 5
bNumEndpoints 2
bInterfaceClass 224
bInterfaceSubClass 1
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 49
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 49
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 254
bInterfaceSubClass 1
bInterfaceProtocol 0
iInterface 0
unknown descriptor type: 07 21 07 88 13 ff 03
Language IDs: none (cannot get min. string descriptor; got len=-1,
error=110:Connection timed out)
Best Rgds,
Andy
On Sun, 23 Jan 2005 18:14:42 +0100, Marcel Holtmann <marcel@holtmann.org> wrote:
> Hi Andy,
>
> there is no need to post this twice ;)
>
> > when I call "hciconfig hci0 up", it prints:
> > Can't init device hci0: Connection timed out (110)
> >
> > Working environment is as follows:
> > 1, Vmware workstation 5.0 + Redhat 9.0, with kernel 2.6.8.1, bluez 2.14
> > 2, Bluetooth subsystem enabled
> > 3, Billionton BlueTooth Dongle Class I USBBTC1A
> > 4, "/etc/rc.d/init.d/bluetooth start" already run
> >
> > Outputs (lspci, lsmod, /proc/bus/usb/devices/,hciconfig, dmesg)
> > 1, output from lspci
> > 00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB
> >
> > 2, output from lsmod
> > Module Size Used by
> > ehci_hcd 42688 0
> > hci_usb 13184 0
> > rfcomm 38712 0
> > l2cap 24128 3 rfcomm
> > autofs 15520 0
> > ohci1394 34912 0
> > ieee1394 110384 1 ohci1394
> > parport_pc 25696 0
> > parport 40672 1 parport_pc
> > bluetooth 48292 3 hci_usb,rfcomm,l2cap
> > usbhid 24800 0
> > uhci_hcd 33160 0
> > usbcore 127540 6 ehci_hcd,hci_usb,usbhid,uhci_hcd
> >
> > 3, output from /proc/bus/usb/devices
> >
> > T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
> > B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
> > D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
> > P: Vendor=0000 ProdID=0000 Rev= 2.06
> > S: Manufacturer=Linux 2.6.8.1 uhci_hcd
> > S: Product=Intel Corp. 82371AB/EB/MB PIIX4 USB
> > S: SerialNumber=0000:00:07.2
> > C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
> > I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
> > E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
> >
> > T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
> > D: Ver= 1.10 Cls=e0(unk. ) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
> > P: Vendor=0a12 ProdID=0001 Rev= 4.87
> > C:* #Ifs= 3 Cfg#= 1 Atr=c0 MxPwr= 0mA
> > I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
> > E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
> > E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> > E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> > I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
> > E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> > E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> > I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
> > E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
> > E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
> > I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
> > E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
> > E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
> > I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
> > E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
> > E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
> > I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
> > E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
> > E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
> > I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
> > E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
> > E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
> > I: If#= 2 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none)
> >
> > 4, output from hciconfig
> > hci0: Type: USB
> > BD Address: 00:00:00:00:00:00 ACL MTU: 0:0 SCO MTU: 0:0
> > DOWN
> > RX bytes:0 acl:0 sco:0 events:0 errors:0
> > TX bytes:0 acl:0 sco:0 commands:0 errors:0
> > Features: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> > Packet type: DM1 DH1 HV1
> > Link policy:
> > Link mode: SLAVE ACCEPT
> >
> > 8, output from dmesg
> > uhci_hcd 0000:00:07.2: suspend_hc
> > uhci_hcd 0000:00:07.2: wakeup_hc
> > uhci_hcd 0000:00:07.2: port 1 portsc 0083
> > hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
> > hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
> > usb 1-1: new full speed USB device using address 3
> > usb 1-1: skipped 1 descriptor after interface
> > usb 1-1: new device strings: Mfr=0, Product=0, SerialNumber=0
> > usb 1-1: hotplug
> > usb 1-1: adding 1-1:1.0 (config #1, interface 0)
> > usb 1-1:1.0: hotplug
> > hci_usb 1-1:1.0: usb_probe_interface
> > hci_usb 1-1:1.0: usb_probe_interface - got id
> > usb 1-1: adding 1-1:1.1 (config #1, interface 1)
> > usb 1-1:1.1: hotplug
> > usb 1-1: adding 1-1:1.2 (config #1, interface 2)
> > usb 1-1:1.2: hotplug
> > hci_usb 1-1:1.2: usb_probe_interface
> > hci_usb 1-1:1.2: usb_probe_interface - got id
> >
> >
> > I really appreciate your kindly help and your time! if you need any
> > further information
> > please let me know, thanx again!
> >
> > Is it a kernel problem? Bluez bug? Configuration Problem? Vmware
> > Restrictions? or what else?
>
> maybe the ISOC transfers are not working perfect within VMware. You can
> disable them with isoc=0 when loading hci_usb. And you should try a
> newer kernel. Check out 2.6.10-mh2 or 2.6.11-rc2.
>
> Regards
>
> Marcel
>
> -------------------------------------------------------
> This SF.Net email is sponsored by: IntelliVIEW -- Interactive Reporting
> Tool for open source databases. Create drag-&-drop reports. Save time
> by over 75%! Publish reports on the web. Export to DOC, XLS, RTF, etc.
> Download a FREE copy at http://www.intelliview.com/go/osdn_nl
> _______________________________________________
> Bluez-users mailing list
> Bluez-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/bluez-users
>
-------------------------------------------------------
This SF.Net email is sponsored by: IntelliVIEW -- Interactive Reporting
Tool for open source databases. Create drag-&-drop reports. Save time
by over 75%! Publish reports on the web. Export to DOC, XLS, RTF, etc.
Download a FREE copy at http://www.intelliview.com/go/osdn_nl
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users
next prev parent reply other threads:[~2005-01-24 3:54 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-01-23 10:10 [Bluez-users] Can't init device hci0 (all information included), help! Thanx a lot!!! Embedded System
2005-01-23 17:14 ` Marcel Holtmann
2005-01-24 3:54 ` Embedded System [this message]
2005-01-24 8:19 ` Michal Semler
2005-01-24 10:05 ` Embedded System
2005-01-24 12:22 ` Marcel Holtmann
2005-01-25 15:23 ` Embedded System
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=c93f2a2905012319541a6c820f@mail.gmail.com \
--to=embed.sys@gmail.com \
--cc=bluez-users@lists.sourceforge.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox