* HP Pavillion a220n problems
@ 2003-09-01 15:34 Frank Jansen
0 siblings, 0 replies; only message in thread
From: Frank Jansen @ 2003-09-01 15:34 UTC (permalink / raw)
To: Linux-net, Linux-config
[-- Attachment #1: Type: text/plain, Size: 433 bytes --]
Just picked up an HP Pavillion a220n and am running into some problems
with the configuration, which causes the on-board network device not to
be detected. I suspect that the problems all stem from the on-board
Nvidia GeForce MX4, as all lspci entries show its name.
I have tried turning off PnP with no change, and am looking for
suggestions for other things to try. The lpsci -v and dmesg outputs are
attached.
Thanks,
Frank
[-- Attachment #2: lspci-v --]
[-- Type: application/octet-stream, Size: 4974 bytes --]
00:00.0 Host bridge: nVidia Corporation: Unknown device 01e0 (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 80c0
Flags: bus master, 66Mhz, fast devsel, latency 0
Memory at f4000000 (32-bit, prefetchable) [size=64M]
Capabilities: [40] AGP version 2.0
Capabilities: [60] #08 [2001]
00:00.1 RAM memory: nVidia Corporation: Unknown device 01eb (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 80c0
Flags: 66Mhz, fast devsel
00:00.2 RAM memory: nVidia Corporation: Unknown device 01ee (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 80c0
Flags: 66Mhz, fast devsel
00:00.3 RAM memory: nVidia Corporation: Unknown device 01ed (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 80c0
Flags: 66Mhz, fast devsel
00:00.4 RAM memory: nVidia Corporation: Unknown device 01ec (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 80c0
Flags: 66Mhz, fast devsel
00:00.5 RAM memory: nVidia Corporation: Unknown device 01ef (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 80c0
Flags: 66Mhz, fast devsel
00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4)
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Flags: bus master, 66Mhz, fast devsel, latency 0
Capabilities: [48] #08 [01e1]
00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 80ad
Flags: 66Mhz, fast devsel, IRQ 10
I/O ports at ec00 [size=32]
Capabilities: [44] Power Management version 2
00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 80ad
Flags: 66Mhz, fast devsel, IRQ 5
Memory at fe900000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 80ad
Flags: bus master, 66Mhz, fast devsel, latency 0, IRQ 5
Memory at fea00000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4) (prog-if 20 [EHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 80ad
Flags: bus master, 66Mhz, fast devsel, latency 0, IRQ 5
Memory at feb00000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] #0a [2080]
Capabilities: [80] Power Management version 2
00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet Controller (rev a1)
Subsystem: Asustek Computer, Inc.: Unknown device 80a7
Flags: bus master, 66Mhz, fast devsel, latency 0, IRQ 3
Memory at fe800000 (32-bit, non-prefetchable) [size=4K]
I/O ports at e880 [size=8]
Capabilities: [44] Power Management version 2
00:06.0 Multimedia audio controller: nVidia Corporation nForce2 AC97 Audio Controler (MCP) (rev a1)
Subsystem: Asustek Computer, Inc.: Unknown device 8095
Flags: bus master, 66Mhz, fast devsel, latency 0, IRQ 11
I/O ports at e000 [size=256]
I/O ports at ef00 [size=128]
Memory at fe600000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
00:08.0 PCI bridge: nVidia Corporation: Unknown device 006c (rev a3) (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2) (prog-if 8a [Master SecP PriP])
Subsystem: Asustek Computer, Inc.: Unknown device 80ad
Flags: bus master, 66Mhz, fast devsel, latency 0
I/O ports at ffa0 [size=16]
Capabilities: [44] Power Management version 2
00:0d.0 FireWire (IEEE 1394): nVidia Corporation nForce2 FireWire (IEEE 1394) Controller (rev a3) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 80af
Flags: bus master, 66Mhz, fast devsel, latency 0, IRQ 11
Memory at fe500000 (32-bit, non-prefetchable) [size=2K]
Memory at fe400000 (32-bit, non-prefetchable) [size=64]
Capabilities: [44] Power Management version 2
00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev a2) (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 64
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
Memory behind bridge: fb900000-fdafffff
Prefetchable memory behind bridge: eb600000-f37fffff
02:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX - nForce GPU] (rev a3) (prog-if 00 [VGA])
Subsystem: Asustek Computer, Inc.: Unknown device 80c0
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 11
Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
Memory at ec000000 (32-bit, prefetchable) [size=64M]
Memory at f3500000 (32-bit, prefetchable) [size=512K]
Expansion ROM at fda00000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Capabilities: [44] AGP version 2.0
[-- Attachment #3: dmesg --]
[-- Type: application/octet-stream, Size: 10851 bytes --]
Linux version 2.4.20-6 (bhcompile@sylvester.devel.redhat.com) (gcc version 3.2.2 20030222 (Red Hat Linux 3.2.2-5)) #1 Thu Feb 27 10:01:19 EST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001bfd0000 (usable)
BIOS-e820: 000000001bfd0000 - 000000001bfdf000 (ACPI data)
BIOS-e820: 000000001bfdf000 - 000000001c000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
447MB LOWMEM available.
On node 0 totalpages: 114640
zone(0): 4096 pages.
zone(1): 110544 pages.
zone(2): 0 pages.
Kernel command line: ro root=LABEL=/ hdd=ide-scsi
ide_setup: hdd=ide-scsi
Initializing CPU#0
Detected 2079.574 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 4141.87 BogoMIPS
Memory: 446636k/458560k available (1312k kernel code, 9360k reserved, 996k data, 128k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000
CPU: AMD Athlon(tm) XP 2600+ stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router default [10de/0060] at 00:01.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA
hda: WDC WD1200AB-22DYA0, ATA DISK drive
blk: queue c03be900, I/O limit 4095Mb (mask 0xffffffff)
hdc: IDE-DVD ROM 16x, ATAPI CD/DVD-ROM drive
hdd: SONY CD-RW CRX215E5, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: host protected area => 1
hda: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=14593/255/63, UDMA(33)
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 145k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 128k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Guessed IRQ 5 for device 00:02.1
PCI: Setting latency timer of device 00:02.1 to 64
usb-ohci.c: USB OHCI at membase 0xdc849000, IRQ 5
usb-ohci.c: usb-00:02.1, PCI device 10de:0067 (nVidia Corporation)
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 3 ports detected
PCI: Guessed IRQ 5 for device 00:02.0
PCI: Setting latency timer of device 00:02.0 to 64
usb-ohci.c: USB OHCI at membase 0xdc84b000, IRQ 5
usb-ohci.c: usb-00:02.0, PCI device 10de:0067 (nVidia Corporation)
usb-ohci.c: USB HC TakeOver failed!
Trying to vfree() nonexistent vm area (dc84b000)
c208beb8 00000005 dc84b000 dc8467fc 00001000 dc8467fc dc847280 c2230000
00000000 c01cd291 c2230000 dc8467fc c2230000 dc847280 00000001 dc842000
c01cd32c dc847280 c2230000 ffffffea 00000001 00000001 dc845f3c dc847280
Call Trace: [<dc8467fc>] ohci_pci_ids [usb-ohci] 0x1c (0xc208bec4))
[<dc8467fc>] ohci_pci_ids [usb-ohci] 0x1c (0xc208becc))
[<dc847280>] ohci_pci_driver [usb-ohci] 0x0 (0xc208bed0))
[<c01cd291>] pci_announce_device [kernel] 0x35 (0xc208bedc))
[<dc8467fc>] ohci_pci_ids [usb-ohci] 0x1c (0xc208bee4))
[<dc847280>] ohci_pci_driver [usb-ohci] 0x0 (0xc208beec))
[<c01cd32c>] pci_register_driver [kernel] 0x60 (0xc208bef8))
[<dc847280>] ohci_pci_driver [usb-ohci] 0x0 (0xc208befc))
[<dc845f3c>] ohci_hcd_init [usb-ohci] 0x30 (0xc208bf10))
[<dc847280>] ohci_pci_driver [usb-ohci] 0x0 (0xc208bf14))
[<c011c6c1>] sys_init_module [kernel] 0x4e5 (0xc208bf1c))
[<dc842060>] ohci_mem_init [usb-ohci] 0x0 (0xc208bf20))
[<dc846924>] .kmodtab [usb-ohci] 0x0 (0xc208bf2c))
[<dc842060>] ohci_mem_init [usb-ohci] 0x0 (0xc208bf58))
[<c01093b3>] system_call [kernel] 0x33 (0xc208bfc0))
PCI: Guessed IRQ 5 for device 00:02.2
PCI: Setting latency timer of device 00:02.2 to 64
ehci-hcd 00:02.2: PCI device 10de:0068 (nVidia Corporation)
ehci-hcd 00:02.2: irq 5, pci mem dc851000
usb.c: new USB bus registered, assigned bus number 2
PCI: 00:02.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
PCI: 00:02.2 PCI cache line size corrected to 64.
ehci-hcd 00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Jan-22
hub.c: USB hub found
hub.c: 6 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
Adding Swap: 4192956k swap-space (priority -1)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ohci1394: $Rev: 693 $ Ben Collins <bcollins@debian.org>
PCI: Setting latency timer of device 00:0d.0 to 64
ohci1394_0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[fe500000-fe5007ff] Max Packet=[2048]
ieee1394: SelfID completion called outside of bus reset!
hdc: ATAPI 40X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: SONY Model: CD-RW CRX215E5 Rev: 5.0E
Type: CD-ROM ANSI SCSI revision: 02
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
ip_tables: (C) 2000-2002 Netfilter core team
spurious 8259A interrupt: IRQ7.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
cdrom: This disc doesn't have any tracks I recognize!
floppy0: data CRC error: track 0, head 0, sector 17, size 2
floppy0: data CRC error: track 0, head 0, sector 17, size 2
end_request: I/O error, dev 02:00 (floppy), sector 16
floppy0: data CRC error: track 0, head 0, sector 17, size 2
floppy0: data CRC error: track 0, head 0, sector 17, size 2
end_request: I/O error, dev 02:00 (floppy), sector 16
FAT: bogus logical sector size 8308
VFS: Can't find a valid FAT filesystem on dev 02:00.
floppy0: data CRC error: track 0, head 0, sector 17, size 2
floppy0: data CRC error: track 0, head 0, sector 17, size 2
end_request: I/O error, dev 02:00 (floppy), sector 16
floppy0: data CRC error: track 0, head 0, sector 17, size 2
floppy0: data CRC error: track 0, head 0, sector 17, size 2
end_request: I/O error, dev 02:00 (floppy), sector 16
floppy0: data CRC error: track 0, head 0, sector 17, size 2
floppy0: data CRC error: track 0, head 0, sector 17, size 2
end_request: I/O error, dev 02:00 (floppy), sector 16
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 02:00.
floppy0: data CRC error: track 0, head 0, sector 17, size 2
floppy0: data CRC error: track 0, head 0, sector 17, size 2
end_request: I/O error, dev 02:00 (floppy), sector 16
floppy0: data CRC error: track 0, head 0, sector 17, size 2
floppy0: data CRC error: track 0, head 0, sector 17, size 2
end_request: I/O error, dev 02:00 (floppy), sector 16
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 02:00.
floppy0: data CRC error: track 0, head 1, sector 2, size 2
floppy0: data CRC error: track 0, head 1, sector 2, size 2
end_request: I/O error, dev 02:00 (floppy), sector 19
floppy0: data CRC error: track 0, head 1, sector 2, size 2
floppy0: data CRC error: track 0, head 1, sector 2, size 2
end_request: I/O error, dev 02:00 (floppy), sector 19
FAT: bogus logical sector size 8308
VFS: Can't find a valid FAT filesystem on dev 02:00.
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2003-09-01 15:34 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2003-09-01 15:34 HP Pavillion a220n problems Frank Jansen
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox