[PATCH V2 1/2] dt-bindings: spi: Documentation for Hi6220 spi driver

[PATCH V2 1/2] dt-bindings: spi: Documentation for Hi6220 spi driver

[Zhong Kaihua]

dt-bindings: spi: Documentation for Hi6220 spi driver

Signed-off-by: Zhong Kaihua <zhongkaihua-hv44wF8Li93QT0dZR+AlfA@public.gmane.org>
---
 .../devicetree/bindings/spi/spi-hi6220.txt         | 45 ++++++++++++++++++++++
 1 file changed, 45 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/spi/spi-hi6220.txt

diff --git a/Documentation/devicetree/bindings/spi/spi-hi6220.txt b/Documentation/devicetree/bindings/spi/spi-hi6220.txt
new file mode 100644
index 0000000..91aa169
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-hi6220.txt
@@ -0,0 +1,45 @@
+Hi6220 SPI controller
+
+Required properties:
+- compatible : "arm,pl022", "arm,primecell"
+- reg : Offset and length of the register set for the device
+- interrupts : Should contain SPI controller interrupt
+- num-cs : total number of chipselects
+
+Required Board Specific Properties:
+
+- #address-cells: should be 1.
+- #size-cells: should be 0.
+
+Optional properties:
+- cs-gpios : should specify GPIOs used for chipselects.
+  The gpios will be referred to as reg = <index> in the SPI child nodes.
+  If unspecified, a single SPI device without a chip select can be used.
+- dmas : Two or more DMA channel specifiers following the convention outlined
+         in bindings/dma/dma.txt
+- dma-names: Names for the dma channels, if present. There must be at
+	     least one channel named "tx" for transmit and named "rx" for
+             receive.
+
+Example:
+             spi_0: spi@f7106000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0x0 0xf7106000 0x0 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <0 50 4>;
+			bus-id = <0>;
+			enable-dma = <1>;
+			dmas =	<&dma0 12 &dma0 13>;
+			dma-names = "rx", "tx";
+
+			clocks = <&clock_sys HI6220_SPI_CLK>;
+			clock-names = "apb_pclk";
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi0_pmx_func &spi0_cfg_func>;
+			num-cs = <4>;
+			cs-gpios = <&gpio6 2 0>, <&gpio6 3 0>, <&gpio6 4 0>, <&gpio6 5 0>;
+
+			status = "ok";
+		};
+
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH V2 2/2] arm64: dts: add Hi6220 spi configuration nodes

[Zhong Kaihua]

arm64: dts: add Hi6220 spi configuration nodes

Signed-off-by: Zhong Kaihua <zhongkaihua@huawei.com>
---
 arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts |  1 +
 arch/arm64/boot/dts/hisilicon/hi6220.dtsi      | 20 ++++++++++++++++++++
 2 files changed, 21 insertions(+)

diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
index 4fb0bdc..2313ae0 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
@@ -23,6 +23,7 @@
 		serial1 = &uart1; /* BT UART */
 		serial2 = &uart2; /* LS Expansion UART0 */
 		serial3 = &uart3; /* LS Expansion UART1 */
+		spi0 = &spi_0;
 	};
 
 	chosen {
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
index 0f11e2a..da0fe37 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
@@ -489,5 +489,25 @@
 			clock-names = "apb_pclk";
 			status = "ok";
 		};
+
+		spi_0: spi@f7106000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0x0 0xf7106000 0x0 0x1000>;
+			interrupts = <0 50 4>;
+			bus-id = <0>;
+			enable-dma = <0>;
+			/*dmas = <&dma0 12 &dma0 13>;*/
+			/*dma-names = "rx", "tx";*/
+
+			clocks = <&sys_ctrl HI6220_SPI_CLK>;
+			clock-names = "apb_pclk";
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi0_pmx_func &spi0_cfg_func>;
+			num-cs = <1>;
+			cs-gpios = <&gpio6 2 0>;
+
+			status = "ok";
+		};
+
 	};
 };
-- 
1.9.1

Re: [PATCH V2 1/2] dt-bindings: spi: Documentation for Hi6220 spi driver

[Rob Herring]

On Thu, Nov 19, 2015 at 04:37:08PM +0800, Zhong Kaihua wrote:
> dt-bindings: spi: Documentation for Hi6220 spi driver
> 
> Signed-off-by: Zhong Kaihua <zhongkaihua-hv44wF8Li93QT0dZR+AlfA@public.gmane.org>
> ---
>  .../devicetree/bindings/spi/spi-hi6220.txt         | 45 ++++++++++++++++++++++
>  1 file changed, 45 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/spi/spi-hi6220.txt
> 
> diff --git a/Documentation/devicetree/bindings/spi/spi-hi6220.txt b/Documentation/devicetree/bindings/spi/spi-hi6220.txt
> new file mode 100644
> index 0000000..91aa169
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/spi-hi6220.txt
> @@ -0,0 +1,45 @@
> +Hi6220 SPI controller
> +
> +Required properties:
> +- compatible : "arm,pl022", "arm,primecell"

If this is just a pl022, then you don't need this document as 
spi_pl022.txt already exists. If HiSilicon has modified this block, then 
you need an additional HiSi specific compatible string and add it to 
spi_pl022.txt.

> +- reg : Offset and length of the register set for the device
> +- interrupts : Should contain SPI controller interrupt
> +- num-cs : total number of chipselects
> +
> +Required Board Specific Properties:
> +
> +- #address-cells: should be 1.
> +- #size-cells: should be 0.
> +
> +Optional properties:
> +- cs-gpios : should specify GPIOs used for chipselects.
> +  The gpios will be referred to as reg = <index> in the SPI child nodes.
> +  If unspecified, a single SPI device without a chip select can be used.
> +- dmas : Two or more DMA channel specifiers following the convention outlined
> +         in bindings/dma/dma.txt
> +- dma-names: Names for the dma channels, if present. There must be at
> +	     least one channel named "tx" for transmit and named "rx" for
> +             receive.
> +
> +Example:
> +             spi_0: spi@f7106000 {
> +			compatible = "arm,pl022", "arm,primecell";
> +			reg = <0x0 0xf7106000 0x0 0x1000>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			interrupts = <0 50 4>;
> +			bus-id = <0>;

This should be removed.

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

答复: [PATCH V2 1/2] dt-bindings: spi: Documentation for Hi6220 spi driver

[zhongkaihua]

This block is not modified and the document is removed.

I just send out V3 patch for SPI on hi6220. Are There any other problems? Thanks

On 2015/11/20 23:39, Rob Herring wrote:> On Thu, Nov 19, 2015 at 04:37:08PM +0800, Zhong Kaihua wrote:
>> dt-bindings: spi: Documentation for Hi6220 spi driver
>>
>> Signed-off-by: Zhong Kaihua <zhongkaihua@huawei.com>
>> ---
>>  .../devicetree/bindings/spi/spi-hi6220.txt         | 45 ++++++++++++++++++++++
>>  1 file changed, 45 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/spi/spi-hi6220.txt
>>
>> diff --git a/Documentation/devicetree/bindings/spi/spi-hi6220.txt b/Documentation/devicetree/bindings/spi/spi-hi6220.txt
>> new file mode 100644
>> index 0000000..91aa169
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/spi/spi-hi6220.txt
>> @@ -0,0 +1,45 @@
>> +Hi6220 SPI controller
>> +
>> +Required properties:
>> +- compatible : "arm,pl022", "arm,primecell"
> 
> If this is just a pl022, then you don't need this document as 
> spi_pl022.txt already exists. If HiSilicon has modified this block, then 
> you need an additional HiSi specific compatible string and add it to 
> spi_pl022.txt.
> 
>> +- reg : Offset and length of the register set for the device
>> +- interrupts : Should contain SPI controller interrupt
>> +- num-cs : total number of chipselects
>> +
>> +Required Board Specific Properties:
>> +
>> +- #address-cells: should be 1.
>> +- #size-cells: should be 0.
>> +
>> +Optional properties:
>> +- cs-gpios : should specify GPIOs used for chipselects.
>> +  The gpios will be referred to as reg = <index> in the SPI child nodes.
>> +  If unspecified, a single SPI device without a chip select can be used.
>> +- dmas : Two or more DMA channel specifiers following the convention outlined
>> +         in bindings/dma/dma.txt
>> +- dma-names: Names for the dma channels, if present. There must be at
>> +	     least one channel named "tx" for transmit and named "rx" for
>> +             receive.
>> +
>> +Example:
>> +             spi_0: spi@f7106000 {
>> +			compatible = "arm,pl022", "arm,primecell";
>> +			reg = <0x0 0xf7106000 0x0 0x1000>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			interrupts = <0 50 4>;
>> +			bus-id = <0>;
> 
> This should be removed.
> 
> 
> .
>