[PATCH v2 0/8] arm64: dts: allwinner: Various DT fixes

[PATCH v2 0/8] arm64: dts: allwinner: Various DT fixes

[Andre Przywara]

Hi,

small update, mostly adding Fixes: tags.
Patch 1/7 has been split up to cover A64 and H6 separately.

I tried to reach out to people with Pine64-LTS boards to clarify on
the blue LED, as it seems like production boards are spread thinly
across developers. We got confirmation from several people with
several board revisions that this LED works and is indeed blue.

I also double checked on the CD pin situation on the two SoPine SOMs
I have, and could confirm their functionality.

Rebased on top of sunxi/dt-for-5.12.

================
a collection of DT fixes I gathered over time:

- Adding usbphy references to [EO]HCI0 nodes (A64, H6)
- Adding Pine64-LTS status LED
- Dropping non-removable from SoPine/Pine64-LTS SD card
- Enabling HS200 @ 150 MHz on Pine H64 (H6)
- Enabling HS200 @ 150 MHz on Pine64-LTS

For details please see the individual patches!

Thanks,
Andre

Changelog v1 .. v2:
- Add Fixes: tags
- Add Chen-Yu's ACKs
- split USB PHY 0 link patch

Andre Przywara (8):
  arm64: dts: allwinner: A64: properly connect USB PHY to port 0
  arm64: dts: allwinner: H6: properly connect USB PHY to port 0
  arm64: dts: allwinner: Pine64-LTS: Add status LED
  arm64: dts: allwinner: Drop non-removable from SoPine/LTS SD card
  arm64: dts: allwinner: H6: Allow up to 150 MHz MMC bus frequency
  arm64: dts: allwinner: A64: Limit MMC2 bus frequency to 150 MHz
  arm64: dts: allwinner: Pine64-LTS/SoPine: Enable HS200 eMMC mode
  arm64: dts: allwinner: Pine H64: Enable HS200 eMMC mode

 .../boot/dts/allwinner/sun50i-a64-pine64-lts.dts      | 11 +++++++++++
 arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts |  5 +----
 .../dts/allwinner/sun50i-a64-sopine-baseboard.dts     |  1 +
 arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi  |  1 -
 arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi         |  6 +++++-
 arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts  |  1 +
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi          |  7 +++++++
 7 files changed, 26 insertions(+), 6 deletions(-)

-- 
2.17.5

[PATCH v2 1/8] arm64: dts: allwinner: A64: properly connect USB PHY to port 0

[Andre Przywara]

In recent Allwinner SoCs the first USB host controller (HCI0) shares
the first PHY with the MUSB controller. Probably to make this sharing
work, we were avoiding to declare this in the DT. This has two
shortcomings:
- U-Boot (which uses the same .dts) cannot use this port in host mode
  without a PHY linked, so we were loosing one USB port there.
- It requires the MUSB driver to be enabled and loaded, although we
  don't actually use it.

To avoid those issues, let's add this PHY link to the A64 .dtsi file.
After all PHY port 0 *is* connected to HCI0, so we should describe
it as this. Remove the part from the Pinebook DTS which already had
this property.

This makes it work in U-Boot, also improves compatiblity when no MUSB
driver is loaded (for instance in distribution installers).

Fixes: dc03a047df1d ("arm64: allwinner: a64: add EHCI0/OHCI0 nodes to A64 DTSI")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts | 4 ----
 arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi         | 4 ++++
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
index 896f34fd9fc3..d07cf05549c3 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
@@ -126,8 +126,6 @@
 };
 
 &ehci0 {
-	phys = <&usbphy 0>;
-	phy-names = "usb";
 	status = "okay";
 };
 
@@ -177,8 +175,6 @@
 };
 
 &ohci0 {
-	phys = <&usbphy 0>;
-	phy-names = "usb";
 	status = "okay";
 };
 
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
index 51cc30e84e26..19e9b8ca8432 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
@@ -593,6 +593,8 @@
 				 <&ccu CLK_USB_OHCI0>;
 			resets = <&ccu RST_BUS_OHCI0>,
 				 <&ccu RST_BUS_EHCI0>;
+			phys = <&usbphy 0>;
+			phy-names = "usb";
 			status = "disabled";
 		};
 
@@ -603,6 +605,8 @@
 			clocks = <&ccu CLK_BUS_OHCI0>,
 				 <&ccu CLK_USB_OHCI0>;
 			resets = <&ccu RST_BUS_OHCI0>;
+			phys = <&usbphy 0>;
+			phy-names = "usb";
 			status = "disabled";
 		};
 
-- 
2.17.5

[PATCH v2 2/8] arm64: dts: allwinner: H6: properly connect USB PHY to port 0

[Andre Przywara]

In recent Allwinner SoCs the first USB host controller (HCI0) shares
the first PHY with the MUSB controller. Probably to make this sharing
work, we were avoiding to declare this in the DT. This has two
shortcomings:
- U-Boot (which uses the same .dts) cannot use this port in host mode
  without a PHY linked, so we were loosing one USB port there.
- It requires the MUSB driver to be enabled and loaded, although we
  don't actually use it.

To avoid those issues, let's add this PHY link to the H6 .dtsi file.
After all PHY port 0 *is* connected to HCI0, so we should describe
it as this.

This makes it work in U-Boot, also improves compatiblity when no MUSB
driver is loaded (for instance in distribution installers).

Fixes: eabb3d424b6d ("arm64: dts: allwinner: h6: add USB2-related device nodes")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
index 8a62a9fbe347..f593cfeaecc9 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
@@ -680,6 +680,8 @@
 				 <&ccu CLK_USB_OHCI0>;
 			resets = <&ccu RST_BUS_OHCI0>,
 				 <&ccu RST_BUS_EHCI0>;
+			phys = <&usb2phy 0>;
+			phy-names = "usb";
 			status = "disabled";
 		};
 
@@ -690,6 +692,8 @@
 			clocks = <&ccu CLK_BUS_OHCI0>,
 				 <&ccu CLK_USB_OHCI0>;
 			resets = <&ccu RST_BUS_OHCI0>;
+			phys = <&usb2phy 0>;
+			phy-names = "usb";
 			status = "disabled";
 		};
 
-- 
2.17.5

[PATCH v2 3/8] arm64: dts: allwinner: Pine64-LTS: Add status LED

[Andre Przywara]

The Pine64-LTS board features a blue status LED on pin PL7.

Describe it in the DT.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 .../boot/dts/allwinner/sun50i-a64-pine64-lts.dts      | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts
index 302e24be0a31..93d271fdbb6c 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts
@@ -1,10 +1,21 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 // Copyright (c) 2018 ARM Ltd.
 
+#include <dt-bindings/leds/common.h>
 #include "sun50i-a64-sopine-baseboard.dts"
 
 / {
 	model = "Pine64 LTS";
 	compatible = "pine64,pine64-lts", "allwinner,sun50i-r18",
 		     "allwinner,sun50i-a64";
+
+	led {
+		compatible = "gpio-leds";
+
+		status {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		};
+	};
 };
-- 
2.17.5

Re: [PATCH v2 3/8] arm64: dts: allwinner: Pine64-LTS: Add status LED

[Heinrich Schuchardt]

On 13.01.21 16:26, Andre Przywara wrote:
> The Pine64-LTS board features a blue status LED on pin PL7.
>
> Describe it in the DT.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

Re: [PATCH v2 3/8] arm64: dts: allwinner: Pine64-LTS: Add status LED

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 1389 bytes --]

Hi,

On Wed, Jan 13, 2021 at 03:26:25PM +0000, Andre Przywara wrote:
> The Pine64-LTS board features a blue status LED on pin PL7.
> 
> Describe it in the DT.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
>  .../boot/dts/allwinner/sun50i-a64-pine64-lts.dts      | 11 +++++++++++
>  1 file changed, 11 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts
> index 302e24be0a31..93d271fdbb6c 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts
> @@ -1,10 +1,21 @@
>  // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>  // Copyright (c) 2018 ARM Ltd.
>  
> +#include <dt-bindings/leds/common.h>
>  #include "sun50i-a64-sopine-baseboard.dts"
>  
>  / {
>  	model = "Pine64 LTS";
>  	compatible = "pine64,pine64-lts", "allwinner,sun50i-r18",
>  		     "allwinner,sun50i-a64";
> +
> +	led {
> +		compatible = "gpio-leds";
> +
> +		status {
> +			function = LED_FUNCTION_STATUS;
> +			color = <LED_COLOR_ID_BLUE>;
> +			gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> +		};

Thanks for fixing the node names, but I guess my comment was a bit too
vague: it's status that needed to be changed, not the upper level one.

I've updated it while applying

Maxime


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[PATCH v2 4/8] arm64: dts: allwinner: Drop non-removable from SoPine/LTS SD card

[Andre Przywara]

The SD card on the SoPine SoM module is somewhat concealed, so was
originally defined as "non-removable".
However there is a working card-detect pin (tested on two different
SoM versions), and in certain SoM base boards it might be actually
accessible at runtime.
Also the Pine64-LTS shares the SoPine base .dtsi, so inherited the
non-removable flag, even though the SD card slot is perfectly accessible
and usable there. (It turns out that just *my* board has a broken card
detect switch, so I originally thought CD wouldn't work on the LTS.)

Drop the "non-removable" flag to describe the SD card slot properly.

Fixes: c3904a269891 ("arm64: allwinner: a64: add DTSI file for SoPine SoM")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi
index c48692b06e1f..3402cec87035 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi
@@ -32,7 +32,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
-	non-removable;
 	disable-wp;
 	bus-width = <4>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
-- 
2.17.5

[PATCH v2 5/8] arm64: dts: allwinner: H6: Allow up to 150 MHz MMC bus frequency

[Andre Przywara]

The H6 manual explicitly lists a frequency limit of 150 MHz for the bus
frequency of the MMC controllers. So far we had no explicit limits in the
DT, which limited eMMC to the spec defined frequencies, or whatever the
driver defines (both Linux and FreeBSD use 52 MHz here).

Put those maximum frequencies in the SoC .dtsi, to allow higher speed
modes (which still would need to be explicitly enabled, per board).

Tested with an eMMC using HS-200 on a Pine H64. Running at the spec'ed
200 MHz indeed fails with I/O errors, but 150 MHz seems to work stably.

Fixes: 8f54bd1595b3 ("arm64: allwinner: h6: add device tree nodes for MMC controllers")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
index f593cfeaecc9..77765d4a05ec 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
@@ -436,6 +436,7 @@
 			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&mmc0_pins>;
+			max-frequency = <150000000>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -452,6 +453,7 @@
 			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&mmc1_pins>;
+			max-frequency = <150000000>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -468,6 +470,7 @@
 			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&mmc2_pins>;
+			max-frequency = <150000000>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
-- 
2.17.5

[PATCH v2 6/8] arm64: dts: allwinner: A64: Limit MMC2 bus frequency to 150 MHz

[Andre Przywara]

In contrast to the H6 (and later) manuals, the A64 datasheet does not
specify any limitations in the maximum possible frequency for eMMC
controllers.
However experimentation has found that a 150 MHz limit similar to other
SoCs and also the MMC0 and MMC1 controllers on the A64 seems to exist
for the MMC2 controller.

Limit the frequency for the MMC2 controller to 150 MHz in the SoC .dtsi.
The Pinebook seems to be the an odd exception, since it apparently seems
to work with 200 MHz as well, so overwrite this in its board .dts file.

Tested on a Pine64-LTS: 200 MHz HS-200 fails, 150 MHz HS-200 works.

Fixes: 22be992faea7 ("arm64: allwinner: a64: Increase the MMC max frequency")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts | 1 +
 arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi         | 2 +-
 2 files changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
index d07cf05549c3..7ae16541d14f 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
@@ -167,6 +167,7 @@
 	pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
 	vmmc-supply = <&reg_dcdc1>;
 	vqmmc-supply = <&reg_eldo1>;
+	max-frequency = <200000000>;
 	bus-width = <8>;
 	non-removable;
 	cap-mmc-hw-reset;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
index 19e9b8ca8432..57786fc120c3 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
@@ -514,7 +514,7 @@
 			resets = <&ccu RST_BUS_MMC2>;
 			reset-names = "ahb";
 			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
-			max-frequency = <200000000>;
+			max-frequency = <150000000>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
-- 
2.17.5

[PATCH v2 7/8] arm64: dts: allwinner: Pine64-LTS/SoPine: Enable HS200 eMMC mode

[Andre Przywara]

The eMMC modules offered for the Pine64 boards are capable of the HS200
eMMC speed mode, when observing the frequency limit of 150 MHz.

Enable that in the DT.

This increases the interface speed from ~80 MB/s to ~120 MB/s.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
---
 arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
index d4069749d721..e22b94c83647 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
@@ -111,6 +111,7 @@
 	bus-width = <8>;
 	non-removable;
 	cap-mmc-hw-reset;
+	mmc-hs200-1_8v;
 	status = "okay";
 };
 
-- 
2.17.5

[PATCH v2 8/8] arm64: dts: allwinner: Pine H64: Enable HS200 eMMC mode

[Andre Przywara]

The eMMC modules offered for the Pine64 boards are capable of the HS200
eMMC speed mode, when observing the frequency limit of 150 MHz.

Enable that in the DT.

This increases the interface speed from ~80 MB/s to ~120 MB/s.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
---
 arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
index 961732c52aa0..15ceba027a73 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
@@ -142,6 +142,7 @@
 	vqmmc-supply = <&reg_bldo2>;
 	non-removable;
 	cap-mmc-hw-reset;
+	mmc-hs200-1_8v;
 	bus-width = <8>;
 	status = "okay";
 };
-- 
2.17.5

Re: [linux-sunxi] [PATCH v2 0/8] arm64: dts: allwinner: Various DT fixes

[Chen-Yu Tsai]

On Wed, Jan 13, 2021 at 11:27 PM Andre Przywara <andre.przywara@arm.com> wrote:
>
> Hi,
>
> small update, mostly adding Fixes: tags.
> Patch 1/7 has been split up to cover A64 and H6 separately.
>
> I tried to reach out to people with Pine64-LTS boards to clarify on
> the blue LED, as it seems like production boards are spread thinly
> across developers. We got confirmation from several people with
> several board revisions that this LED works and is indeed blue.
>
> I also double checked on the CD pin situation on the two SoPine SOMs
> I have, and could confirm their functionality.
>
> Rebased on top of sunxi/dt-for-5.12.
>
> ================
> a collection of DT fixes I gathered over time:
>
> - Adding usbphy references to [EO]HCI0 nodes (A64, H6)
> - Adding Pine64-LTS status LED
> - Dropping non-removable from SoPine/Pine64-LTS SD card
> - Enabling HS200 @ 150 MHz on Pine H64 (H6)
> - Enabling HS200 @ 150 MHz on Pine64-LTS
>
> For details please see the individual patches!
>
> Thanks,
> Andre
>
> Changelog v1 .. v2:
> - Add Fixes: tags
> - Add Chen-Yu's ACKs
> - split USB PHY 0 link patch
>
> Andre Przywara (8):
>   arm64: dts: allwinner: A64: properly connect USB PHY to port 0
>   arm64: dts: allwinner: H6: properly connect USB PHY to port 0
>   arm64: dts: allwinner: Pine64-LTS: Add status LED
>   arm64: dts: allwinner: Drop non-removable from SoPine/LTS SD card
>   arm64: dts: allwinner: H6: Allow up to 150 MHz MMC bus frequency
>   arm64: dts: allwinner: A64: Limit MMC2 bus frequency to 150 MHz
>   arm64: dts: allwinner: Pine64-LTS/SoPine: Enable HS200 eMMC mode
>   arm64: dts: allwinner: Pine H64: Enable HS200 eMMC mode

Everything looks good to me.

Acked-by: Chen-Yu Tsai <wens@csie.org>

Re: [PATCH v2 0/8] arm64: dts: allwinner: Various DT fixes

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 1084 bytes --]

On Wed, Jan 13, 2021 at 03:26:22PM +0000, Andre Przywara wrote:
> Hi,
> 
> small update, mostly adding Fixes: tags.
> Patch 1/7 has been split up to cover A64 and H6 separately.
> 
> I tried to reach out to people with Pine64-LTS boards to clarify on
> the blue LED, as it seems like production boards are spread thinly
> across developers. We got confirmation from several people with
> several board revisions that this LED works and is indeed blue.
> 
> I also double checked on the CD pin situation on the two SoPine SOMs
> I have, and could confirm their functionality.
> 
> Rebased on top of sunxi/dt-for-5.12.
> 
> ================
> a collection of DT fixes I gathered over time:
> 
> - Adding usbphy references to [EO]HCI0 nodes (A64, H6)
> - Adding Pine64-LTS status LED
> - Dropping non-removable from SoPine/Pine64-LTS SD card
> - Enabling HS200 @ 150 MHz on Pine H64 (H6)
> - Enabling HS200 @ 150 MHz on Pine64-LTS
> 
> For details please see the individual patches!

Applied the series (with the fix mentionned in patch 3)

Thanks!
Maxime

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]