From: Changhuang Liang <changhuang.liang@starfivetech.com>
To: Linus Walleij <linusw@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Emil Renner Berthing <kernel@esmil.dk>,
Paul Walmsley <pjw@kernel.org>, Albert Ou <aou@eecs.berkeley.edu>,
Palmer Dabbelt <palmer@dabbelt.com>,
Alexandre Ghiti <alex@ghiti.fr>,
Philipp Zabel <p.zabel@pengutronix.de>,
Bartosz Golaszewski <brgl@kernel.org>
Cc: linux-gpio@vger.kernel.org, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org, linux-riscv@lists.infradead.org,
Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>,
Changhuang Liang <changhuang.liang@starfivetech.com>
Subject: [PATCH v1 02/20] pinctrl: starfive: Add StarFive JHB100 sys0 controller driver
Date: Fri, 24 Apr 2026 04:13:12 -0700 [thread overview]
Message-ID: <20260424111330.702272-3-changhuang.liang@starfivetech.com> (raw)
In-Reply-To: <20260424111330.702272-1-changhuang.liang@starfivetech.com>
Add pinctrl driver for StarFive JHB100 SoC System-0(sys0) pinctrl
controller.
Signed-off-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
MAINTAINERS | 8 +
drivers/pinctrl/starfive/Kconfig | 21 +
drivers/pinctrl/starfive/Makefile | 3 +
.../starfive/pinctrl-starfive-jhb100-sys0.c | 111 +
.../starfive/pinctrl-starfive-jhb100.c | 1821 +++++++++++++++++
.../starfive/pinctrl-starfive-jhb100.h | 191 ++
6 files changed, 2155 insertions(+)
create mode 100644 drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys0.c
create mode 100644 drivers/pinctrl/starfive/pinctrl-starfive-jhb100.c
create mode 100644 drivers/pinctrl/starfive/pinctrl-starfive-jhb100.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 4ddf8ba2e60d..b3ad0dee7307 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -25319,6 +25319,14 @@ L: linux-riscv@lists.infradead.org
S: Maintained
F: arch/riscv/boot/dts/starfive/jhb100*
+STARFIVE JHB100 PINCTRL DRIVERS
+M: Changhuang Liang <changhuang.liang@starfivetech.com>
+M: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
+L: linux-gpio@vger.kernel.org
+S: Maintained
+F: Documentation/devicetree/bindings/pinctrl/starfive,jhb1*.yaml
+F: drivers/pinctrl/starfive/pinctrl-starfive-jhb1*
+
STARFIVE JHB100 RESET CONTROLLER DRIVERS
M: Changhuang Liang <changhuang.liang@starfivetech.com>
S: Maintained
diff --git a/drivers/pinctrl/starfive/Kconfig b/drivers/pinctrl/starfive/Kconfig
index 8192ac2087fc..dc53070ee2c8 100644
--- a/drivers/pinctrl/starfive/Kconfig
+++ b/drivers/pinctrl/starfive/Kconfig
@@ -49,3 +49,24 @@ config PINCTRL_STARFIVE_JH7110_AON
This also provides an interface to the GPIO pins not used by other
peripherals supporting inputs, outputs, configuring pull-up/pull-down
and interrupts on input changes.
+
+config PINCTRL_STARFIVE_JHB100
+ bool
+ select GENERIC_PINCONF
+ select GENERIC_PINCTRL_GROUPS
+ select GENERIC_PINMUX_FUNCTIONS
+ select GPIOLIB
+ select GPIOLIB_IRQCHIP
+ select OF_GPIO
+
+config PINCTRL_STARFIVE_JHB100_SYS0
+ tristate "StarFive JHB100 SoC System-0 pinctrl and GPIO driver"
+ depends on ARCH_STARFIVE || COMPILE_TEST
+ depends on OF
+ select PINCTRL_STARFIVE_JHB100
+ default ARCH_STARFIVE
+ help
+ Say yes here to support system-0 pin control on the StarFive JHB100 SoC.
+ This also provides an interface to the GPIO pins not used by other
+ peripherals supporting inputs, outputs, configuring pull-up/pull-down
+ and interrupts on input changes.
diff --git a/drivers/pinctrl/starfive/Makefile b/drivers/pinctrl/starfive/Makefile
index ee0d32d085cb..c0d368f413bc 100644
--- a/drivers/pinctrl/starfive/Makefile
+++ b/drivers/pinctrl/starfive/Makefile
@@ -5,3 +5,6 @@ obj-$(CONFIG_PINCTRL_STARFIVE_JH7100) += pinctrl-starfive-jh7100.o
obj-$(CONFIG_PINCTRL_STARFIVE_JH7110) += pinctrl-starfive-jh7110.o
obj-$(CONFIG_PINCTRL_STARFIVE_JH7110_SYS) += pinctrl-starfive-jh7110-sys.o
obj-$(CONFIG_PINCTRL_STARFIVE_JH7110_AON) += pinctrl-starfive-jh7110-aon.o
+
+obj-$(CONFIG_PINCTRL_STARFIVE_JHB100) += pinctrl-starfive-jhb100.o
+obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0) += pinctrl-starfive-jhb100-sys0.o
diff --git a/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys0.c b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys0.c
new file mode 100644
index 000000000000..1ee3e9a617da
--- /dev/null
+++ b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys0.c
@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Pinctrl / GPIO driver for StarFive JHB100 SoC System-0 domain
+ *
+ * Copyright (C) 2024 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <yuklin.soo@starfivetech.com>
+ *
+ */
+
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-starfive-jhb100.h"
+
+static const struct jhb100_pin_layout_desc jhb100_sys0_pl_desc[] = {
+ { .pin_start = 0, .pin_cnt = 3, .name = "gpio", .gpio_func_sel = 0, },
+ { .pin_start = 3, .pin_cnt = 1, .name = "bmcpcierp_pe2rst_out", .gpio_func_sel = 1, },
+ { .pin_start = 4, .pin_cnt = 1, .name = "testen", .gpio_func_sel = -1, },
+ { .pin_start = 5, .pin_cnt = 1, .name = "syspok_in", .gpio_func_sel = -1, },
+ { .pin_start = 6, .pin_cnt = 1, .name = "sysrstn_in", .gpio_func_sel = -1, },
+ { .pin_start = 7, .pin_cnt = 1, .name = "perstn0_in", .gpio_func_sel = -1, },
+ { .pin_start = 8, .pin_cnt = 1, .name = "perstn1_in", .gpio_func_sel = -1, },
+ { .pin_start = 9, .pin_cnt = 1, .name = "aprstn_out", .gpio_func_sel = -1, },
+ { .pin_start = 10, .pin_cnt = 1, .name = "pcierp_wake", .gpio_func_sel = -1, },
+ { 0xff },
+};
+
+static struct config_reg_layout_desc jhb100_sys0_pinctrl_crl_desc[] = {
+ {
+ .pin_start = 0,
+ .pin_cnt = 4,
+ .drive_strength_2bit = { .shift = 0, .width = 2 },
+ .input_enable = { .shift = 2, .width = 1 },
+ .pull_down = { .shift = 3, .width = 1 },
+ .pull_up = { .shift = 4, .width = 1 },
+ .slew_rate = { .shift = 5, .width = 1 },
+ .schmitt_trigger_select = { .shift = 6, .width = 1 },
+ .reserved = { .shift = 7, .width = 8 },
+ .debounce_width = { .shift = 15, .width = 17 },
+ },
+ {
+ .pin_start = 4,
+ .pin_cnt = 5,
+ .schmitt_trigger_select = { .shift = 0, .width = 1 },
+ .reserved = { .shift = 1, .width = 31 },
+ },
+ {
+ .pin_start = 9,
+ .pin_cnt = 1,
+ .drive_strength_2bit = { .shift = 0, .width = 2 },
+ .slew_rate = { .shift = 2, .width = 1 },
+ .reserved = { .shift = 3, .width = 29 },
+ },
+ {
+ .pin_start = 10,
+ .pin_cnt = 1,
+ .drive_strength_2bit = { .shift = 0, .width = 2 },
+ .input_enable = { .shift = 2, .width = 1 },
+ .pull_down = { .shift = 3, .width = 1 },
+ .pull_up = { .shift = 4, .width = 1 },
+ .slew_rate = { .shift = 5, .width = 1 },
+ .schmitt_trigger_select = { .shift = 6, .width = 1 },
+ .reserved = { .shift = 7, .width = 25 },
+ },
+ { 0xff },
+};
+
+struct starfive_pinctrl_regs jhb100_sys0_pinctrl_regs = {
+ .config = { .reg = 0x0c, .width_per_pin = 1 },
+ .output = { .reg = 0x38, .width_per_pin = 1 },
+ .output_en = { .reg = 0x3c, .width_per_pin = 1 },
+ .gpio_status = { .reg = 0x40, .width_per_pin = 1 },
+ .func_sel = { .reg = 0x44, .width_per_pin = 2 },
+ .irq_en = { .reg = 0x48, .width_per_pin = 1 },
+ .irq_status = { .reg = 0x4c, .width_per_pin = 1 },
+ .irq_clr = { .reg = 0x50, .width_per_pin = 1 },
+ .irq_trigger = { .reg = 0x54, .width_per_pin = 1 },
+ .irq_level = { .reg = 0x58, .width_per_pin = 1 },
+ .irq_both_edge = { .reg = 0x5c, .width_per_pin = 1 },
+ .irq_edge = { .reg = 0x60, .width_per_pin = 1 },
+};
+
+static const struct jhb100_pinctrl_domain_info jhb100_sys0_pinctrl_info = {
+ .name = "jhb100-sys0",
+ .gc_base = -1,
+ .pl_desc = jhb100_sys0_pl_desc,
+ .crl_desc = jhb100_sys0_pinctrl_crl_desc,
+ .regs = &jhb100_sys0_pinctrl_regs,
+};
+
+static const struct of_device_id jhb100_sys0_pinctrl_of_match[] = {
+ {
+ .compatible = "starfive,jhb100-sys0-pinctrl",
+ .data = &jhb100_sys0_pinctrl_info,
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, jhb100_sys0_pinctrl_of_match);
+
+static struct platform_driver jhb100_sys0_pinctrl_driver = {
+ .probe = jhb100_pinctrl_probe,
+ .driver = {
+ .name = "starfive-jhb100-sys0-pinctrl",
+ .of_match_table = jhb100_sys0_pinctrl_of_match,
+ },
+};
+module_platform_driver(jhb100_sys0_pinctrl_driver);
+
+MODULE_DESCRIPTION("Pinctrl driver for StarFive JHB100 SoC System-0 domain");
+MODULE_AUTHOR("Alex Soo <yuklin.soo@starfivetech.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/pinctrl/starfive/pinctrl-starfive-jhb100.c b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100.c
new file mode 100644
index 000000000000..3e4c60d17bb8
--- /dev/null
+++ b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100.c
@@ -0,0 +1,1821 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Pinctrl / GPIO driver for StarFive JHB100 SoC
+ *
+ * Copyright (C) 2024 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <yuklin.soo@starfivetech.com>
+ *
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/gpio/driver.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/minmax.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+#include <linux/seq_file.h>
+#include <linux/spinlock.h>
+#include <linux/string.h>
+#include <linux/sort.h>
+
+#include <linux/pinctrl/consumer.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+
+#include "pinctrl-starfive-jhb100.h"
+
+#define GPOUT_LOW 0
+#define GPOUT_HIGH 1
+
+#define GPOEN_ENABLE 0
+#define GPOEN_DISABLE 1
+
+#define MAX_DEBOUNCE_WIDTH_STAGES 0x1FFFF
+
+/* Custom pinconf parameters */
+#define STARFIVE_PIN_CONFIG_GMAC_VSEL (PIN_CONFIG_END + 1)
+#define STARFIVE_PIN_CONFIG_DEBOUNCE_WIDTH (PIN_CONFIG_END + 2)
+#define STARFIVE_PIN_DRIVE_I2C_FAST_MODE (PIN_CONFIG_END + 3)
+#define STARFIVE_PIN_DRIVE_I2C_FAST_MODE_PLUS (PIN_CONFIG_END + 4)
+#define STARFIVE_PIN_OPEN_DRAIN_PULLUP_SELECT (PIN_CONFIG_END + 5)
+#define STARFIVE_PIN_VGA_RTE_SELECT (PIN_CONFIG_END + 6)
+
+struct field_info {
+ const char *name;
+ unsigned int shift;
+ unsigned int width;
+ unsigned int end;
+};
+
+static const struct pinconf_generic_params jhb100_custom_bindings[] = {
+ { "starfive,gmac-vsel", STARFIVE_PIN_CONFIG_GMAC_VSEL, 0 },
+ { "starfive,debounce-width", STARFIVE_PIN_CONFIG_DEBOUNCE_WIDTH, 0 },
+ { "starfive,drive-i2c-fast-mode", STARFIVE_PIN_DRIVE_I2C_FAST_MODE, 0 },
+ { "starfive,drive-i2c-fast-mode-plus", STARFIVE_PIN_DRIVE_I2C_FAST_MODE_PLUS, 0 },
+ { "starfive,i2c-open-drain-pull-up-ohm", STARFIVE_PIN_OPEN_DRAIN_PULLUP_SELECT, 0 },
+ { "starfive,vga-rte", STARFIVE_PIN_VGA_RTE_SELECT, 0 },
+};
+
+static unsigned int jhb100_pinmux_pin(u32 v)
+{
+ return FIELD_GET(GENMASK(7, 0), v);
+}
+
+static u32 jhb100_pinmux_function(u32 v)
+{
+ return FIELD_GET(GENMASK(9, 8), v);
+}
+
+static u32 jhb100_get_func_sel(struct jhb100_pinctrl *sfp, unsigned int pin)
+{
+ struct starfive_pinctrl_regs *pinctrl_regs = sfp->info->regs;
+ unsigned int offset = 4 * (pin / 16);
+ unsigned int shift = pinctrl_regs->func_sel.width_per_pin * (pin % 16);
+ u32 func_sel_mask;
+ u32 func_sel;
+ void __iomem *reg_gpio_func_sel;
+ unsigned long flags;
+
+ reg_gpio_func_sel = sfp->base + pinctrl_regs->func_sel.reg + offset;
+ func_sel_mask = GENMASK(pinctrl_regs->func_sel.width_per_pin - 1, 0) << shift;
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ func_sel = readl_relaxed(reg_gpio_func_sel);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+
+ return (func_sel & func_sel_mask) >> shift;
+}
+
+static struct config_reg_layout_desc *get_crl_desc_by_pin(struct jhb100_pinctrl *sfp,
+ unsigned int pin)
+{
+ struct config_reg_layout_desc *crl_desc = sfp->info->crl_desc;
+ unsigned int i = 0;
+
+ do {
+ if (pin >= crl_desc[i].pin_start &&
+ pin < crl_desc[i].pin_start + crl_desc[i].pin_cnt)
+ return &crl_desc[i];
+ } while (crl_desc[i++].pin_start != 0xff);
+
+ return NULL;
+}
+
+static struct jhb100_pinctrl *jhb100_from_irq_data(struct irq_data *d)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+
+ return container_of(gc, struct jhb100_pinctrl, gc);
+}
+
+static struct jhb100_pinctrl *jhb100_from_irq_desc(struct irq_desc *desc)
+{
+ struct gpio_chip *gc = irq_desc_get_handler_data(desc);
+
+ return container_of(gc, struct jhb100_pinctrl, gc);
+}
+
+static int jhb100_dt_node_to_map(struct pinctrl_dev *pctldev,
+ struct device_node *np,
+ struct pinctrl_map **maps,
+ unsigned int *num_maps)
+{
+ struct jhb100_pinctrl *sfp = pinctrl_dev_get_drvdata(pctldev);
+ unsigned int old_num_funs, new_num_funs;
+ struct device *dev = sfp->gc.parent;
+ struct device_node *child;
+ struct pinctrl_map *map;
+ struct property *pinmux_p;
+ const char **pgnames;
+ const char *mux_grpname = NULL;
+ const char *grpname = NULL;
+ int ngroups;
+ int nmaps;
+ int ret;
+
+ ngroups = 0;
+ for_each_child_of_node(np, child)
+ ngroups += 1;
+ nmaps = 2 * ngroups;
+
+ pgnames = devm_kcalloc(dev, ngroups, sizeof(*pgnames), GFP_KERNEL);
+ if (!pgnames)
+ return -ENOMEM;
+
+ map = kcalloc(nmaps, sizeof(*map), GFP_KERNEL);
+ if (!map)
+ return -ENOMEM;
+
+ nmaps = 0;
+ ngroups = 0;
+ mutex_lock(&sfp->mutex);
+ for_each_child_of_node(np, child) {
+ unsigned int old_num_groups, new_num_groups;
+ const char *pin_grpname;
+ int nmux;
+ int *mpins;
+ u32 *pinmux;
+ int i;
+
+ pinmux_p = of_find_property(child, "pinmux", NULL);
+ if (!pinmux_p) {
+ dev_err(dev,
+ "%pOFn.%pOFn: no muxing or pin config is specified\n",
+ np, child);
+ ret = -EINVAL;
+ goto put_child;
+ } else {
+ nmux = of_property_count_u32_elems(child, "pinmux");
+ if (nmux < 1) {
+ dev_err(dev,
+ "invalid pinctrl group %pOFn.%pOFn: no pinmux is set\n",
+ np, child);
+ ret = -EINVAL;
+ goto put_child;
+ }
+ }
+
+ grpname = kasprintf(GFP_KERNEL, "%pOFn.%pOFn", np, child);
+ if (!grpname) {
+ ret = -ENOMEM;
+ goto put_child;
+ }
+
+ pgnames[ngroups] = devm_kstrdup(dev, grpname, GFP_KERNEL);
+ if (!pgnames[ngroups]) {
+ ret = -ENOMEM;
+ goto free_grpname;
+ }
+ ngroups++;
+
+ pin_grpname = devm_kstrdup(dev, grpname, GFP_KERNEL);
+ if (!pin_grpname) {
+ ret = -ENOMEM;
+ goto free_grpname;
+ }
+
+ mux_grpname = kstrdup(grpname, GFP_KERNEL);
+ if (!mux_grpname) {
+ ret = -ENOMEM;
+ goto free_grpname;
+ }
+
+ mpins = devm_kcalloc(dev, nmux, sizeof(*mpins), GFP_KERNEL);
+ if (!mpins) {
+ ret = -ENOMEM;
+ goto free_mux_grpname;
+ }
+
+ pinmux = devm_kcalloc(dev, nmux, sizeof(*pinmux), GFP_KERNEL);
+ if (!pinmux) {
+ ret = -ENOMEM;
+ goto free_mux_grpname;
+ }
+
+ ret = of_property_read_u32_array(child, "pinmux", pinmux, nmux);
+ if (ret)
+ goto free_mux_grpname;
+
+ for (i = 0; i < nmux; i++)
+ mpins[i] = jhb100_pinmux_pin(pinmux[i]);
+
+ map[nmaps].type = PIN_MAP_TYPE_MUX_GROUP;
+ map[nmaps].data.mux.function = np->name;
+ map[nmaps].data.mux.group = mux_grpname;
+ nmaps += 1;
+
+ old_num_groups = pctldev->num_groups;
+
+ ret = pinctrl_generic_add_group(pctldev, pin_grpname,
+ mpins, nmux, pinmux);
+ if (ret < 0) {
+ dev_err(dev, "error adding group %s: %d\n", pin_grpname, ret);
+ goto free_mux_grpname;
+ }
+
+ new_num_groups = pctldev->num_groups;
+ if (new_num_groups == old_num_groups) {
+ devm_kfree(dev, mpins);
+ devm_kfree(dev, pinmux);
+ devm_kfree(dev, pin_grpname);
+ }
+
+ ret = pinconf_generic_parse_dt_config(child, pctldev,
+ &map[nmaps].data.configs.configs,
+ &map[nmaps].data.configs.num_configs);
+ if (ret) {
+ dev_err(dev, "error parsing pin config of group %s: %d\n",
+ grpname, ret);
+ goto free_mux_grpname;
+ }
+
+ /* don't create a map if there are no pinconf settings */
+ if (map[nmaps].data.configs.num_configs == 0) {
+ kfree(grpname);
+ continue;
+ }
+
+ map[nmaps].type = PIN_MAP_TYPE_CONFIGS_GROUP;
+ map[nmaps].data.configs.group_or_pin = grpname;
+ nmaps += 1;
+ }
+
+ old_num_funs = pctldev->num_functions;
+ ret = pinmux_generic_add_function(pctldev, np->name,
+ pgnames, ngroups, NULL);
+ if (ret < 0) {
+ dev_err(dev, "error adding function %s: %d\n", np->name, ret);
+ goto free_mux_grpname;
+ }
+
+ new_num_funs = pctldev->num_functions;
+ if (new_num_funs == old_num_funs) {
+ int i;
+
+ for (i = 0; i < ngroups; i++)
+ devm_kfree(dev, pgnames[i]);
+
+ devm_kfree(dev, pgnames);
+ }
+
+ mutex_unlock(&sfp->mutex);
+
+ *maps = map;
+ *num_maps = nmaps;
+ return 0;
+
+free_mux_grpname:
+ kfree(mux_grpname);
+
+free_grpname:
+ kfree(grpname);
+
+put_child:
+ of_node_put(child);
+ mutex_unlock(&sfp->mutex);
+ kfree(map);
+ return ret;
+}
+
+static void jhb100_dt_free_map(struct pinctrl_dev *pctldev, struct pinctrl_map *map,
+ unsigned int num_maps)
+{
+ int i;
+
+ for (i = 0; i < num_maps; i++) {
+ switch (map[i].type) {
+ case PIN_MAP_TYPE_MUX_GROUP:
+ kfree(map[i].data.mux.group);
+ break;
+ case PIN_MAP_TYPE_CONFIGS_GROUP:
+ kfree(map[i].data.configs.group_or_pin);
+ default:
+ break;
+ }
+ }
+
+ pinctrl_utils_free_map(pctldev, map, num_maps);
+}
+
+static const struct pinctrl_ops jhb100_pinctrl_ops = {
+ .get_groups_count = pinctrl_generic_get_group_count,
+ .get_group_name = pinctrl_generic_get_group_name,
+ .get_group_pins = pinctrl_generic_get_group_pins,
+ .dt_node_to_map = jhb100_dt_node_to_map,
+ .dt_free_map = jhb100_dt_free_map,
+};
+
+static void jhb100_set_gpioval(struct jhb100_pinctrl *sfp, unsigned int pin,
+ unsigned int val)
+{
+ const struct jhb100_pinctrl_domain_info *info = sfp->info;
+ unsigned int offset = 4 * (pin / 32);
+ unsigned int shift = 1 * (pin % 32);
+ unsigned int fs_offset = 4 * (pin / 16);
+ unsigned int fs_shift = 2 * (pin % 16);
+ u32 gpio_o_mask;
+ u32 gpio_oen_mask;
+ u32 func_sel_mask;
+ u32 dout, doen, fs;
+ void __iomem *reg_gpio_o;
+ void __iomem *reg_gpio_oen;
+ void __iomem *reg_gpio_func_sel;
+ unsigned long flags;
+
+ reg_gpio_o = sfp->base + info->regs->output.reg + offset;
+ reg_gpio_oen = sfp->base + info->regs->output_en.reg + offset;
+ reg_gpio_func_sel = sfp->base + info->regs->func_sel.reg + fs_offset;
+
+ gpio_o_mask = GENMASK(info->regs->output.width_per_pin - 1, 0) << shift;
+ gpio_oen_mask = GENMASK(info->regs->output_en.width_per_pin - 1, 0) << shift;
+ func_sel_mask = GENMASK(info->regs->func_sel.width_per_pin - 1, 0) << fs_shift;
+ dout = val << shift;
+ doen = 0;
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ fs = readl_relaxed(reg_gpio_func_sel);
+ if (fs & func_sel_mask) {
+ fs &= ~func_sel_mask;
+ writel_relaxed(fs, reg_gpio_func_sel);
+ }
+ dout |= readl_relaxed(reg_gpio_o) & ~gpio_o_mask;
+ writel_relaxed(dout, reg_gpio_o);
+ doen |= readl_relaxed(reg_gpio_oen) & ~gpio_oen_mask;
+ writel_relaxed(doen, reg_gpio_oen);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+}
+
+static void jhb100_set_function(struct jhb100_pinctrl *sfp,
+ unsigned int pin, u32 func)
+{
+ struct starfive_pinctrl_regs *pinctrl_regs = sfp->info->regs;
+ void __iomem *func_sel_reg;
+ unsigned long flags;
+ u32 func_sel_mask;
+ u32 func_sel_val;
+ unsigned int offset = 4 * (pin / (32 / pinctrl_regs->func_sel.width_per_pin));
+ unsigned int shift = pinctrl_regs->func_sel.width_per_pin *
+ (pin % (32 / pinctrl_regs->func_sel.width_per_pin));
+
+ if (!pinctrl_regs->func_sel.reg || !pinctrl_regs->func_sel.width_per_pin)
+ return;
+
+ func_sel_reg = sfp->base + pinctrl_regs->func_sel.reg + offset;
+ func_sel_mask = GENMASK(pinctrl_regs->func_sel.width_per_pin - 1, 0) << shift;
+ func_sel_val = func << shift;
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ func_sel_val |= readl_relaxed(func_sel_reg) & ~func_sel_mask;
+ writel_relaxed(func_sel_val, func_sel_reg);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+}
+
+static int jhb100_set_one_pin_mux(struct jhb100_pinctrl *sfp,
+ unsigned int pin,
+ u32 func,
+ int val)
+{
+ const struct pinctrl_pin_desc *desc = &sfp->pins[pin];
+ struct device *dev = sfp->gc.parent;
+ int gpio_func_sel = sfp->gpio_func_sel_arr[pin];
+
+ jhb100_set_function(sfp, pin, func);
+
+ if (pin < sfp->gc.ngpio && (val == 0 || val == 1)) {
+ if (func == gpio_func_sel)
+ jhb100_set_gpioval(sfp, pin, val);
+ else
+ dev_err(dev, "pin (%s) is not a GPIO. func=%d/%d\n",
+ desc->name, func, gpio_func_sel);
+ }
+
+ return 0;
+}
+
+static int jhb100_set_mux(struct pinctrl_dev *pctldev,
+ unsigned int fsel, unsigned int gsel)
+{
+ struct jhb100_pinctrl *sfp = pinctrl_dev_get_drvdata(pctldev);
+ const struct group_desc *group;
+ const u32 *pinmux;
+ unsigned int i;
+
+ group = pinctrl_generic_get_group(pctldev, gsel);
+ if (!group)
+ return -EINVAL;
+
+ pinmux = group->data;
+
+ for (i = 0; i < group->grp.npins; i++) {
+ u32 v = pinmux[i];
+
+ jhb100_set_one_pin_mux(sfp,
+ jhb100_pinmux_pin(v),
+ jhb100_pinmux_function(v),
+ -1);
+ }
+
+ return 0;
+}
+
+static const struct pinmux_ops jhb100_pinmux_ops = {
+ .get_functions_count = pinmux_generic_get_function_count,
+ .get_function_name = pinmux_generic_get_function_name,
+ .get_function_groups = pinmux_generic_get_function_groups,
+ .set_mux = jhb100_set_mux,
+};
+
+static const u8 jhb100_drive_strength_ma[4] = { 2, 4, 8, 12 };
+
+static const u8 jhb100_drive_strength_ma_3bit[8] = { 2, 5, 8, 10, 14, 16, 18, 20 };
+
+static u32 jhb100_padcfg_ds_to_mA(u32 padcfg)
+{
+ return jhb100_drive_strength_ma[padcfg];
+}
+
+static u32 jhb100_padcfg_ds_to_mA_3bit(u32 padcfg)
+{
+ return jhb100_drive_strength_ma_3bit[padcfg];
+}
+
+static u32 jhb100_padcfg_ds_to_uA(u32 padcfg)
+{
+ return (jhb100_drive_strength_ma[padcfg] * 1000);
+}
+
+static u32 jhb100_padcfg_ds_to_uA_3bit(u32 padcfg)
+{
+ return (jhb100_drive_strength_ma_3bit[padcfg] * 1000);
+}
+
+static u32 jhb100_padcfg_ds_from_mA(u32 v)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(jhb100_drive_strength_ma); i++) {
+ if (v <= jhb100_drive_strength_ma[i])
+ break;
+ }
+ return i;
+}
+
+static u32 jhb100_padcfg_ds_from_mA_3bit(u32 v)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(jhb100_drive_strength_ma_3bit); i++) {
+ if (v <= jhb100_drive_strength_ma_3bit[i])
+ break;
+ }
+ return i;
+}
+
+static u32 jhb100_padcfg_ds_from_uA(u32 v)
+{
+ /* Convert from uA to mA */
+ v /= 1000;
+
+ return jhb100_padcfg_ds_from_mA(v);
+}
+
+static u32 jhb100_padcfg_ds_from_uA_3bit(u32 v)
+{
+ /* Convert from uA to mA */
+ v /= 1000;
+
+ return jhb100_padcfg_ds_from_mA_3bit(v);
+}
+
+static void jhb100_padcfg_rmw(struct jhb100_pinctrl *sfp,
+ unsigned int pin, u32 mask, u32 value)
+{
+ void __iomem *reg;
+ unsigned int offset;
+ unsigned long flags;
+ int padcfg_base;
+
+ padcfg_base = sfp->info->regs->config.reg;
+
+ offset = 4 * pin;
+
+ reg = sfp->base + padcfg_base + offset;
+
+ value &= mask;
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ value |= readl_relaxed(reg) & ~mask;
+ writel_relaxed(value, reg);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+}
+
+static int jhb100_pinconf_get(struct pinctrl_dev *pctldev,
+ unsigned int pin, unsigned long *config)
+{
+ struct jhb100_pinctrl *sfp = pinctrl_dev_get_drvdata(pctldev);
+ int param = pinconf_to_config_param(*config);
+ struct device *dev = sfp->gc.parent;
+ struct config_reg_layout_desc *crl_desc;
+ unsigned int offset;
+ u32 padcfg, arg;
+ bool enabled;
+ int padcfg_base;
+
+ padcfg_base = sfp->info->regs->config.reg;
+
+ offset = 4 * pin;
+
+ if (pin <= sfp->npins)
+ padcfg = readl_relaxed(sfp->base + padcfg_base + offset);
+ else
+ return -EINVAL;
+
+ crl_desc = get_crl_desc_by_pin(sfp, pin);
+ if (!crl_desc) {
+ dev_err(dev, "pin %d can't not found reg layout descriptor\n", pin);
+ return -EINVAL;
+ }
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ arg = 0;
+
+ if (!RL_DESC_SUPPORTED(crl_desc, pull_down) ||
+ !RL_DESC_SUPPORTED(crl_desc, pull_up))
+ return -EOPNOTSUPP;
+
+ enabled = !(padcfg & (RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up)));
+ break;
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ arg = 1;
+
+ if (!RL_DESC_SUPPORTED(crl_desc, pull_down))
+ return -EOPNOTSUPP;
+
+ enabled = (padcfg & RL_DESC_GENMASK(crl_desc, pull_down))
+ >> RL_DESC_SHIFT(crl_desc, pull_down);
+ break;
+ case PIN_CONFIG_BIAS_PULL_UP:
+ arg = 1;
+
+ if (!RL_DESC_SUPPORTED(crl_desc, pull_up))
+ return -EOPNOTSUPP;
+
+ enabled = (padcfg & RL_DESC_GENMASK(crl_desc, pull_up))
+ >> RL_DESC_SHIFT(crl_desc, pull_up);
+ break;
+ case PIN_CONFIG_DRIVE_STRENGTH:
+ enabled = true;
+
+ if (RL_DESC_SUPPORTED(crl_desc, drive_strength_2bit))
+ arg = jhb100_padcfg_ds_to_mA(padcfg <<
+ RL_DESC_SHIFT(crl_desc,
+ drive_strength_2bit));
+ else if (RL_DESC_SUPPORTED(crl_desc, drive_strength_3bit))
+ arg = jhb100_padcfg_ds_to_mA_3bit(padcfg <<
+ RL_DESC_SHIFT(crl_desc,
+ drive_strength_3bit));
+ else
+ return -EOPNOTSUPP;
+ break;
+ case PIN_CONFIG_DRIVE_STRENGTH_UA:
+ enabled = true;
+
+ if (RL_DESC_SUPPORTED(crl_desc, drive_strength_2bit))
+ arg = jhb100_padcfg_ds_to_uA(padcfg
+ << RL_DESC_SHIFT(crl_desc, drive_strength_2bit));
+ else if (RL_DESC_SUPPORTED(crl_desc, drive_strength_3bit))
+ arg = jhb100_padcfg_ds_to_uA_3bit(padcfg
+ << RL_DESC_SHIFT(crl_desc, drive_strength_3bit));
+ else
+ return -EOPNOTSUPP;
+ break;
+ case PIN_CONFIG_INPUT_ENABLE:
+ if (!RL_DESC_SUPPORTED(crl_desc, input_enable))
+ return -EOPNOTSUPP;
+
+ enabled = (padcfg & RL_DESC_GENMASK(crl_desc, input_enable))
+ >> RL_DESC_SHIFT(crl_desc, input_enable);
+ arg = enabled;
+ break;
+ case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+ if (!RL_DESC_SUPPORTED(crl_desc, schmitt_trigger_select))
+ return -EOPNOTSUPP;
+
+ enabled = (padcfg & RL_DESC_GENMASK(crl_desc, schmitt_trigger_select))
+ >> RL_DESC_SHIFT(crl_desc, schmitt_trigger_select);
+ arg = enabled;
+ break;
+ case PIN_CONFIG_SLEW_RATE:
+ enabled = true;
+
+ if (!RL_DESC_SUPPORTED(crl_desc, slew_rate))
+ return -EOPNOTSUPP;
+
+ arg = (padcfg & RL_DESC_GENMASK(crl_desc, slew_rate))
+ >> RL_DESC_SHIFT(crl_desc, slew_rate);
+ break;
+ default:
+ return -ENOTSUPP;
+ }
+
+ *config = pinconf_to_config_packed(param, arg);
+ return enabled ? 0 : -EINVAL;
+}
+
+static int jhb100_pinconf_set(struct pinctrl_dev *pctldev,
+ unsigned int gpio, unsigned long *config,
+ unsigned int num_configs)
+{
+ struct jhb100_pinctrl *sfp = pinctrl_dev_get_drvdata(pctldev);
+ struct device *dev = sfp->gc.parent;
+ struct config_reg_layout_desc *crl_desc;
+ u32 param;
+ u32 arg;
+ u32 value;
+ u32 mask;
+ int i;
+
+ crl_desc = get_crl_desc_by_pin(sfp, gpio);
+ if (!crl_desc) {
+ dev_err(dev, "pin %d can't not found reg layout descriptor\n", gpio);
+ return -EINVAL;
+ }
+
+ for (i = 0; i < num_configs; i++) {
+ param = pinconf_to_config_param(config[i]);
+ arg = pinconf_to_config_argument(config[i]);
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ if (!RL_DESC_SUPPORTED(crl_desc, pull_down) ||
+ !RL_DESC_SUPPORTED(crl_desc, pull_up))
+ return -EOPNOTSUPP;
+
+ mask = RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up);
+ value = 0;
+ break;
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ if (!RL_DESC_SUPPORTED(crl_desc, pull_down) ||
+ !RL_DESC_SUPPORTED(crl_desc, pull_up))
+ return -EOPNOTSUPP;
+
+ mask = RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up);
+ value = RL_DESC_GENMASK(crl_desc, pull_down);
+ break;
+ case PIN_CONFIG_BIAS_PULL_UP:
+ if (!RL_DESC_SUPPORTED(crl_desc, pull_down) ||
+ !RL_DESC_SUPPORTED(crl_desc, pull_up))
+ return -EOPNOTSUPP;
+
+ mask = RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up);
+ value = RL_DESC_GENMASK(crl_desc, pull_up);
+ break;
+ case PIN_CONFIG_DRIVE_PUSH_PULL:
+ return 0;
+ case PIN_CONFIG_INPUT_ENABLE:
+ if (!RL_DESC_SUPPORTED(crl_desc, input_enable))
+ return -EOPNOTSUPP;
+
+ mask = RL_DESC_GENMASK(crl_desc, input_enable);
+ value = arg ? RL_DESC_GENMASK(crl_desc, input_enable) : 0;
+ break;
+ case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+ if (!RL_DESC_SUPPORTED(crl_desc, schmitt_trigger_select))
+ return -EOPNOTSUPP;
+
+ mask = RL_DESC_GENMASK(crl_desc, schmitt_trigger_select);
+ value = arg ? RL_DESC_GENMASK(crl_desc, schmitt_trigger_select) : 0;
+ break;
+ case STARFIVE_PIN_CONFIG_DEBOUNCE_WIDTH:
+ if (arg > MAX_DEBOUNCE_WIDTH_STAGES)
+ arg = MAX_DEBOUNCE_WIDTH_STAGES;
+
+ if (!RL_DESC_SUPPORTED(crl_desc, debounce_width))
+ return -EOPNOTSUPP;
+
+ mask = RL_DESC_GENMASK(crl_desc, debounce_width);
+ value = arg ? (arg << RL_DESC_SHIFT(crl_desc, debounce_width)) : 0;
+ break;
+ case STARFIVE_PIN_CONFIG_GMAC_VSEL:
+ if (!RL_DESC_SUPPORTED_FUNC(crl_desc, vsel,
+ BIT(jhb100_get_func_sel(sfp, gpio))))
+ return -EOPNOTSUPP;
+
+ mask = RL_DESC_GENMASK(crl_desc, vsel);
+ value = arg ? arg << RL_DESC_SHIFT(crl_desc, vsel) : 0;
+ break;
+ case STARFIVE_PIN_VGA_RTE_SELECT:
+ if (!RL_DESC_SUPPORTED(crl_desc, retention_signal_bus))
+ return -EOPNOTSUPP;
+
+ mask = RL_DESC_GENMASK(crl_desc, retention_signal_bus);
+ value = arg ? RL_DESC_GENMASK(crl_desc, retention_signal_bus) : 0;
+ break;
+ default:
+ return -ENOTSUPP;
+ }
+
+ jhb100_padcfg_rmw(sfp, gpio, mask, value);
+ }
+
+ return 0;
+}
+
+static int jhb100_pinconf_group_get(struct pinctrl_dev *pctldev,
+ unsigned int gsel,
+ unsigned long *config)
+{
+ const struct group_desc *group;
+
+ group = pinctrl_generic_get_group(pctldev, gsel);
+ if (!group)
+ return -EINVAL;
+
+ return jhb100_pinconf_get(pctldev, group->grp.pins[0], config);
+}
+
+static int jhb100_pinconf_group_set(struct pinctrl_dev *pctldev,
+ unsigned int gsel,
+ unsigned long *configs,
+ unsigned int num_configs)
+{
+ struct jhb100_pinctrl *sfp = pinctrl_dev_get_drvdata(pctldev);
+ struct device *dev = sfp->gc.parent;
+ struct config_reg_layout_desc *crl_desc;
+ const struct group_desc *group;
+ u32 mask, value;
+ int i;
+
+ group = pinctrl_generic_get_group(pctldev, gsel);
+ if (!group)
+ return -EINVAL;
+
+ mask = 0;
+ value = 0;
+ for (i = 0; i < num_configs; i++) {
+ int param = pinconf_to_config_param(configs[i]);
+ u32 arg = pinconf_to_config_argument(configs[i]);
+
+ crl_desc = get_crl_desc_by_pin(sfp, group->grp.pins[0]);
+ if (!crl_desc) {
+ dev_err(dev, "pin %d can't not found reg layout descriptor\n",
+ group->grp.pins[i]);
+ return -EINVAL;
+ }
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ if (!RL_DESC_SUPPORTED(crl_desc, pull_down) ||
+ !RL_DESC_SUPPORTED(crl_desc, pull_up))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up);
+ value &= ~(RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up));
+ break;
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ if (!arg || !RL_DESC_SUPPORTED(crl_desc, pull_down) ||
+ !RL_DESC_SUPPORTED(crl_desc, pull_up))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up);
+ value &= ~(RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up));
+ value |= RL_DESC_GENMASK(crl_desc, pull_down);
+ break;
+ case PIN_CONFIG_BIAS_PULL_UP:
+ if (!arg || !RL_DESC_SUPPORTED(crl_desc, pull_down) ||
+ !RL_DESC_SUPPORTED(crl_desc, pull_up))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up);
+ value &= ~(RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up));
+ value |= RL_DESC_GENMASK(crl_desc, pull_up);
+ break;
+ case PIN_CONFIG_DRIVE_STRENGTH:
+ if (RL_DESC_SUPPORTED(crl_desc, drive_strength_2bit)) {
+ mask |= RL_DESC_GENMASK(crl_desc, drive_strength_2bit);
+ value &= ~RL_DESC_GENMASK(crl_desc, drive_strength_2bit);
+ value |= jhb100_padcfg_ds_from_mA(arg) <<
+ RL_DESC_SHIFT(crl_desc, drive_strength_2bit);
+ } else if (RL_DESC_SUPPORTED(crl_desc, drive_strength_3bit)) {
+ mask |= RL_DESC_GENMASK(crl_desc, drive_strength_3bit);
+ value &= ~RL_DESC_GENMASK(crl_desc, drive_strength_3bit);
+ value |= jhb100_padcfg_ds_from_mA_3bit(arg) <<
+ RL_DESC_SHIFT(crl_desc, drive_strength_3bit);
+ } else {
+ return -EOPNOTSUPP;
+ }
+ break;
+ case PIN_CONFIG_DRIVE_STRENGTH_UA:
+ if (RL_DESC_SUPPORTED(crl_desc, drive_strength_2bit)) {
+ mask |= RL_DESC_GENMASK(crl_desc, drive_strength_2bit);
+ value &= ~RL_DESC_GENMASK(crl_desc, drive_strength_2bit);
+ value |= jhb100_padcfg_ds_from_uA(arg) <<
+ RL_DESC_SHIFT(crl_desc, drive_strength_2bit);
+ } else if (RL_DESC_SUPPORTED(crl_desc, drive_strength_3bit)) {
+ mask |= RL_DESC_GENMASK(crl_desc, drive_strength_3bit);
+ value &= ~RL_DESC_GENMASK(crl_desc, drive_strength_3bit);
+ value |= jhb100_padcfg_ds_from_uA_3bit(arg) <<
+ RL_DESC_SHIFT(crl_desc, drive_strength_3bit);
+ } else {
+ return -EOPNOTSUPP;
+ }
+ break;
+ case PIN_CONFIG_INPUT_ENABLE:
+ if (!RL_DESC_SUPPORTED(crl_desc, input_enable))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, input_enable);
+ value = arg ? (value | RL_DESC_GENMASK(crl_desc, input_enable))
+ : value;
+ break;
+ case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+ if (!RL_DESC_SUPPORTED(crl_desc, schmitt_trigger_select))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, schmitt_trigger_select);
+ value = arg
+ ? (value | RL_DESC_GENMASK(crl_desc, schmitt_trigger_select))
+ : value;
+ break;
+ case PIN_CONFIG_SLEW_RATE:
+ if (!RL_DESC_SUPPORTED(crl_desc, slew_rate))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, slew_rate);
+ value = arg ? (value | RL_DESC_GENMASK(crl_desc, slew_rate)) : value;
+ break;
+ case PIN_CONFIG_DRIVE_PUSH_PULL:
+ if (!RL_DESC_SUPPORTED(crl_desc, mode_select))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, mode_select);
+ value &= ~RL_DESC_GENMASK(crl_desc, mode_select);
+ value |= JHB100_PUSH_PULL <<
+ RL_DESC_SHIFT(crl_desc, mode_select);
+ break;
+ case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+ if (!RL_DESC_SUPPORTED(crl_desc, mode_select))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, mode_select);
+ value &= ~RL_DESC_GENMASK(crl_desc, mode_select);
+ value |= JHB100_OPEN_DRAIN <<
+ RL_DESC_SHIFT(crl_desc, mode_select);
+ break;
+ case STARFIVE_PIN_DRIVE_I2C_FAST_MODE:
+ if (!RL_DESC_SUPPORTED(crl_desc, mode_select))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, mode_select);
+ value &= ~RL_DESC_GENMASK(crl_desc, mode_select);
+ value |= JHB100_LEGACY_FAST_MODE <<
+ RL_DESC_SHIFT(crl_desc, mode_select);
+ break;
+ case STARFIVE_PIN_DRIVE_I2C_FAST_MODE_PLUS:
+ if (!RL_DESC_SUPPORTED(crl_desc, mode_select))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, mode_select);
+ value &= ~RL_DESC_GENMASK(crl_desc, mode_select);
+ value |= JHB100_LEGACY_FAST_MODE_PLUS <<
+ RL_DESC_SHIFT(crl_desc, mode_select);
+ break;
+ case STARFIVE_PIN_OPEN_DRAIN_PULLUP_SELECT:
+ if (!RL_DESC_SUPPORTED(crl_desc, open_drain_pull_up_sel))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, open_drain_pull_up_sel);
+ value &= ~RL_DESC_GENMASK(crl_desc, open_drain_pull_up_sel);
+ switch (arg) {
+ case 600:
+ value |= JHB100_I2C_OPEN_DRAIN_PU_600_OHMS <<
+ RL_DESC_SHIFT(crl_desc, open_drain_pull_up_sel);
+ break;
+ case 900:
+ value |= JHB100_I2C_OPEN_DRAIN_PU_900_OHMS <<
+ RL_DESC_SHIFT(crl_desc, open_drain_pull_up_sel);
+ break;
+ case 1200:
+ value |= JHB100_I2C_OPEN_DRAIN_PU_1200_OHMS <<
+ RL_DESC_SHIFT(crl_desc, open_drain_pull_up_sel);
+ break;
+ case 2000:
+ value |= JHB100_I2C_OPEN_DRAIN_PU_2000_OHMS <<
+ RL_DESC_SHIFT(crl_desc, open_drain_pull_up_sel);
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
+ break;
+ case STARFIVE_PIN_CONFIG_DEBOUNCE_WIDTH:
+ if (!RL_DESC_SUPPORTED(crl_desc, debounce_width))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, debounce_width);
+ value &= ~RL_DESC_GENMASK(crl_desc, debounce_width);
+ value = arg
+ ? (value | (arg << RL_DESC_SHIFT(crl_desc, debounce_width)))
+ : value;
+ break;
+ case STARFIVE_PIN_CONFIG_GMAC_VSEL:
+ if (!RL_DESC_SUPPORTED(crl_desc, vsel))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, vsel);
+ value &= ~RL_DESC_GENMASK(crl_desc, vsel);
+ value = arg
+ ? (value | (arg << RL_DESC_SHIFT(crl_desc, vsel)))
+ : value;
+ break;
+ case STARFIVE_PIN_VGA_RTE_SELECT:
+ if (!RL_DESC_SUPPORTED(crl_desc, retention_signal_bus))
+ return -EOPNOTSUPP;
+
+ mask |= RL_DESC_GENMASK(crl_desc, retention_signal_bus);
+ value &= ~RL_DESC_GENMASK(crl_desc, retention_signal_bus);
+ value = arg
+ ? (value | (arg << RL_DESC_SHIFT(crl_desc, retention_signal_bus)))
+ : value;
+ break;
+ default:
+ return -ENOTSUPP;
+ }
+ }
+
+ for (i = 0; i < group->grp.npins; i++)
+ jhb100_padcfg_rmw(sfp, group->grp.pins[i], mask, value);
+
+ return 0;
+}
+
+static const struct pinconf_ops jhb100_pinconf_ops = {
+ .pin_config_get = jhb100_pinconf_get,
+ .pin_config_set = jhb100_pinconf_set,
+ .pin_config_group_get = jhb100_pinconf_group_get,
+ .pin_config_group_set = jhb100_pinconf_group_set,
+ .is_generic = true,
+};
+
+static int jhb100_gpio_get_direction(struct gpio_chip *gc,
+ unsigned int gpio)
+{
+ struct jhb100_pinctrl *sfp = container_of(gc, struct jhb100_pinctrl, gc);
+ const struct jhb100_pinctrl_domain_info *info = sfp->info;
+ unsigned int offset = 4 * (gpio / 32);
+ unsigned int shift = 1 * (gpio % 32);
+ u32 gpio_oen_mask;
+ u32 doen;
+ void __iomem *reg_gpio_oen;
+
+ reg_gpio_oen = sfp->base + info->regs->output_en.reg + offset;
+ gpio_oen_mask = GENMASK(info->regs->output_en.width_per_pin - 1, 0) << shift;
+
+ doen = (readl_relaxed(reg_gpio_oen) & gpio_oen_mask) >> shift;
+
+ return doen == GPOEN_ENABLE ? GPIO_LINE_DIRECTION_OUT : GPIO_LINE_DIRECTION_IN;
+}
+
+static int jhb100_gpio_direction_input(struct gpio_chip *gc,
+ unsigned int gpio)
+{
+ struct jhb100_pinctrl *sfp = container_of(gc, struct jhb100_pinctrl, gc);
+ struct device *dev = sfp->gc.parent;
+ struct config_reg_layout_desc *crl_desc;
+
+ crl_desc = get_crl_desc_by_pin(sfp, gpio);
+ if (!crl_desc) {
+ dev_err(dev, "pin %d can't not found reg layout descriptor\n",
+ gpio);
+ return -EINVAL;
+ }
+
+ jhb100_padcfg_rmw(sfp, gpio,
+ RL_DESC_GENMASK(crl_desc, input_enable) |
+ RL_DESC_GENMASK(crl_desc, schmitt_trigger_select),
+ RL_DESC_GENMASK(crl_desc, input_enable) |
+ RL_DESC_GENMASK(crl_desc, schmitt_trigger_select));
+
+ jhb100_set_one_pin_mux(sfp, gpio, 0, -1);
+
+ return 0;
+}
+
+static int jhb100_gpio_direction_output(struct gpio_chip *gc,
+ unsigned int gpio, int value)
+{
+ struct jhb100_pinctrl *sfp = container_of(gc, struct jhb100_pinctrl, gc);
+ struct device *dev = sfp->gc.parent;
+ struct config_reg_layout_desc *crl_desc;
+
+ jhb100_set_one_pin_mux(sfp, gpio, 0,
+ value ? GPOUT_HIGH : GPOUT_LOW);
+
+ crl_desc = get_crl_desc_by_pin(sfp, gpio);
+ if (!crl_desc) {
+ dev_err(dev, "pin %d can't not found reg layout descriptor\n",
+ gpio);
+ return -EINVAL;
+ }
+
+ jhb100_padcfg_rmw(sfp, gpio,
+ RL_DESC_GENMASK(crl_desc, input_enable) |
+ RL_DESC_GENMASK(crl_desc, schmitt_trigger_select) |
+ RL_DESC_GENMASK(crl_desc, pull_down) |
+ RL_DESC_GENMASK(crl_desc, pull_up),
+ 0);
+
+ return 0;
+}
+
+static int jhb100_gpio_get(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct jhb100_pinctrl *sfp = container_of(gc, struct jhb100_pinctrl, gc);
+ const struct jhb100_pinctrl_domain_info *info = sfp->info;
+ unsigned int offset = 4 * (gpio / 32);
+ unsigned int shift = 1 * (gpio % 32);
+ u32 gpio_oen_mask = GENMASK(info->regs->output_en.width_per_pin - 1, 0) << shift;
+ u32 doen = 0;
+ void __iomem *reg_gpio_oen;
+ void __iomem *reg;
+ unsigned long flags;
+
+ reg_gpio_oen = sfp->base + info->regs->output_en.reg + offset;
+ reg = sfp->base + info->regs->gpio_status.reg + offset;
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ doen = readl_relaxed(reg_gpio_oen) | gpio_oen_mask;
+ writel_relaxed(doen, reg_gpio_oen);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+
+ return !!(readl_relaxed(reg) & BIT(gpio % 32));
+}
+
+static int jhb100_gpio_set(struct gpio_chip *gc, unsigned int gpio, int value)
+{
+ struct jhb100_pinctrl *sfp = container_of(gc, struct jhb100_pinctrl, gc);
+ const struct jhb100_pinctrl_domain_info *info = sfp->info;
+ unsigned int offset = 4 * (gpio / 32);
+ unsigned int shift = 1 * (gpio % 32);
+ void __iomem *reg_dout;
+ u32 dout;
+ u32 mask;
+ unsigned long flags;
+
+ reg_dout = sfp->base + info->regs->output.reg + offset;
+ dout = (value ? GPOUT_HIGH : GPOUT_LOW) << shift;
+ mask = GENMASK(info->regs->output.width_per_pin - 1, 0) << shift;
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ dout |= readl_relaxed(reg_dout) & ~mask;
+ writel_relaxed(dout, reg_dout);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+
+ return 0;
+}
+
+static void jhb100_irq_ack(struct irq_data *d)
+{
+ struct jhb100_pinctrl *sfp = jhb100_from_irq_data(d);
+ struct starfive_pinctrl_regs *pinctrl_regs = sfp->info->regs;
+ irq_hw_number_t gpio = irqd_to_hwirq(d);
+ void __iomem *ic;
+ u32 mask;
+ unsigned long flags;
+ u32 value;
+
+ ic = sfp->base + pinctrl_regs->irq_clr.reg + 4 * (gpio / 32);
+ mask = BIT(gpio % 32);
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ value = readl_relaxed(ic) & ~mask;
+ writel_relaxed(value | mask, ic);
+ value = readl_relaxed(ic) & ~mask;
+ writel_relaxed(value, ic);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+}
+
+static void jhb100_irq_mask(struct irq_data *d)
+{
+ struct jhb100_pinctrl *sfp = jhb100_from_irq_data(d);
+ struct starfive_pinctrl_regs *pinctrl_regs = sfp->info->regs;
+ irq_hw_number_t gpio = irqd_to_hwirq(d);
+ void __iomem *ien;
+ u32 mask;
+ unsigned long flags;
+ u32 value;
+
+ ien = sfp->base + pinctrl_regs->irq_en.reg + 4 * (gpio / 32);
+ mask = BIT(gpio % 32);
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ value = readl_relaxed(ien) & ~mask;
+ writel_relaxed(value, ien);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+
+ gpiochip_disable_irq(&sfp->gc, d->hwirq);
+}
+
+static void jhb100_irq_mask_ack(struct irq_data *d)
+{
+ struct jhb100_pinctrl *sfp = jhb100_from_irq_data(d);
+ struct starfive_pinctrl_regs *pinctrl_regs = sfp->info->regs;
+ irq_hw_number_t gpio = irqd_to_hwirq(d);
+ void __iomem *ien;
+ void __iomem *ic;
+ u32 mask = BIT(gpio % 32);
+ unsigned long flags;
+ u32 value;
+
+ ien = sfp->base + pinctrl_regs->irq_en.reg + 4 * (gpio / 32);
+ ic = sfp->base + pinctrl_regs->irq_clr.reg + 4 * (gpio / 32);
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ value = readl_relaxed(ien) & ~mask;
+ writel_relaxed(value, ien);
+
+ value = readl_relaxed(ic) & ~mask;
+ writel_relaxed(value | mask, ic);
+ value = readl_relaxed(ic) & ~mask;
+ writel_relaxed(value, ic);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+}
+
+static void jhb100_irq_unmask(struct irq_data *d)
+{
+ struct jhb100_pinctrl *sfp = jhb100_from_irq_data(d);
+ struct starfive_pinctrl_regs *pinctrl_regs = sfp->info->regs;
+ irq_hw_number_t gpio = irqd_to_hwirq(d);
+ void __iomem *ien;
+ u32 mask;
+ unsigned long flags;
+ u32 value;
+
+ ien = sfp->base + pinctrl_regs->irq_en.reg + 4 * (gpio / 32);
+ mask = BIT(gpio % 32);
+
+ gpiochip_enable_irq(&sfp->gc, d->hwirq);
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ value = readl_relaxed(ien) | mask;
+ writel_relaxed(value, ien);
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+}
+
+static int jhb100_irq_set_type(struct irq_data *d, unsigned int trigger)
+{
+ struct jhb100_pinctrl *sfp = jhb100_from_irq_data(d);
+ struct starfive_pinctrl_regs *pinctrl_regs = sfp->info->regs;
+ irq_hw_number_t gpio = irqd_to_hwirq(d);
+ void __iomem *base;
+ u32 mask;
+ u32 irq_type, edge_both, polarity;
+ unsigned long flags;
+
+ base = sfp->base + 4 * (gpio / 32);
+ mask = BIT(gpio % 32);
+
+ switch (trigger) {
+ case IRQ_TYPE_EDGE_RISING:
+ irq_type = mask; /* 1: edge triggered */
+ edge_both = 0; /* 0: single edge */
+ polarity = mask; /* 1: rising edge */
+ break;
+ case IRQ_TYPE_EDGE_FALLING:
+ irq_type = mask; /* 1: edge triggered */
+ edge_both = 0; /* 0: single edge */
+ polarity = 0; /* 0: falling edge */
+ break;
+ case IRQ_TYPE_EDGE_BOTH:
+ irq_type = mask; /* 1: edge triggered */
+ edge_both = mask; /* 1: both edges */
+ polarity = 0; /* 0: ignored */
+ break;
+ case IRQ_TYPE_LEVEL_HIGH:
+ irq_type = 0; /* 0: level triggered */
+ edge_both = 0; /* 0: ignored */
+ polarity = mask; /* 1: high level */
+ break;
+ case IRQ_TYPE_LEVEL_LOW:
+ irq_type = 0; /* 0: level triggered */
+ edge_both = 0; /* 0: ignored */
+ polarity = 0; /* 0: low level */
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ if (trigger & IRQ_TYPE_EDGE_BOTH)
+ irq_set_handler_locked(d, handle_edge_irq);
+ else
+ irq_set_handler_locked(d, handle_level_irq);
+
+ raw_spin_lock_irqsave(&sfp->lock, flags);
+ irq_type |= readl_relaxed(base + pinctrl_regs->irq_trigger.reg) & ~mask;
+ writel_relaxed(irq_type, base + pinctrl_regs->irq_trigger.reg);
+
+ edge_both |= readl_relaxed(base + pinctrl_regs->irq_both_edge.reg) & ~mask;
+ writel_relaxed(edge_both, base + pinctrl_regs->irq_both_edge.reg);
+
+ if (irq_type & mask) { /* edge polarity */
+ polarity |= readl_relaxed(base + pinctrl_regs->irq_edge.reg) & ~mask;
+ writel_relaxed(polarity, base + pinctrl_regs->irq_edge.reg);
+ } else if (irq_type == 0) { /* level polarity */
+ polarity |= readl_relaxed(base + pinctrl_regs->irq_level.reg) & ~mask;
+ writel_relaxed(polarity, base + pinctrl_regs->irq_level.reg);
+ }
+ raw_spin_unlock_irqrestore(&sfp->lock, flags);
+ return 0;
+}
+
+static int jhb100_irq_set_wake(struct irq_data *d, unsigned int enable)
+{
+ struct jhb100_pinctrl *sfp = jhb100_from_irq_data(d);
+ int ret = 0;
+
+ if (enable)
+ ret = enable_irq_wake(sfp->wakeup_irq);
+ else
+ ret = disable_irq_wake(sfp->wakeup_irq);
+ if (ret)
+ dev_err(sfp->dev, "failed to %s wake-up interrupt\n",
+ enable ? "enable" : "disable");
+
+ return ret;
+}
+
+static void jhb100_irq_print_chip(struct irq_data *d, struct seq_file *p)
+{
+ struct jhb100_pinctrl *sfp = jhb100_from_irq_data(d);
+
+ seq_printf(p, sfp->gc.label);
+}
+
+static const struct irq_chip jhb100_irq_chip = {
+ .irq_ack = jhb100_irq_ack,
+ .irq_mask = jhb100_irq_mask,
+ .irq_mask_ack = jhb100_irq_mask_ack,
+ .irq_unmask = jhb100_irq_unmask,
+ .irq_set_type = jhb100_irq_set_type,
+ .irq_set_wake = jhb100_irq_set_wake,
+ .irq_print_chip = jhb100_irq_print_chip,
+ .flags = IRQCHIP_SET_TYPE_MASKED |
+ IRQCHIP_IMMUTABLE |
+ IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND |
+ IRQCHIP_MASK_ON_SUSPEND |
+ IRQCHIP_SKIP_SET_WAKE,
+ GPIOCHIP_IRQ_RESOURCE_HELPERS,
+};
+
+static void jhb100_gpio_irq_handler(struct irq_desc *desc)
+{
+ struct jhb100_pinctrl *sfp = jhb100_from_irq_desc(desc);
+ struct irq_chip *chip = irq_desc_get_chip(desc);
+ struct gpio_irq_chip *girq = &sfp->gc.irq;
+ struct starfive_pinctrl_regs *pinctrl_regs = sfp->info->regs;
+ unsigned long is;
+ unsigned int pin;
+ unsigned int total, size, remain = sfp->npins;
+
+ chained_irq_enter(chip, desc);
+
+ for (total = 0, size = 0; total < sfp->npins; total += 32, remain -= size) {
+ is = readl_relaxed(sfp->base + pinctrl_regs->irq_status.reg +
+ (total >> 3));
+ size = umin(remain, 32);
+
+ for_each_set_bit(pin, &is, size) {
+ if (sfp->gpio_func_sel_arr[pin] >= 0)
+ generic_handle_domain_irq(girq->domain, pin);
+ }
+ }
+
+ chained_irq_exit(chip, desc);
+}
+
+static int jhb100_gpio_init_hw(struct gpio_chip *gc)
+{
+ struct jhb100_pinctrl *sfp = container_of(gc, struct jhb100_pinctrl, gc);
+ struct starfive_pinctrl_regs *pinctrl_regs = sfp->info->regs;
+ unsigned int i;
+
+ for (i = 0; i < sfp->npins; i += 32) {
+ /* mask all GPIO interrupts */
+ writel_relaxed(0U, sfp->base + pinctrl_regs->irq_en.reg + (i >> 3));
+ /* clear all interrupts */
+ writel_relaxed(~0U, sfp->base + pinctrl_regs->irq_clr.reg + (i >> 3));
+ writel_relaxed(0U, sfp->base + pinctrl_regs->irq_clr.reg + (i >> 3));
+ }
+
+ return 0;
+}
+
+static int field_compare(const void *a, const void *b)
+{
+ const struct field_info *fa = (const struct field_info *)a;
+ const struct field_info *fb = (const struct field_info *)b;
+
+ if (fa->shift < fb->shift)
+ return -1;
+
+ if (fa->shift > fb->shift)
+ return 1;
+
+ return 0;
+}
+
+static int check_crl_desc(struct jhb100_pinctrl *sfp, unsigned int index,
+ const struct config_reg_layout_desc *desc)
+{
+ struct device *dev = sfp->gc.parent;
+ struct field_info *fields;
+ int field_cnt = 0;
+ int num, i;
+
+ num = sizeof(struct config_reg_layout_desc) / sizeof(struct reg_layout_field);
+
+ fields = kcalloc(num, sizeof(struct field_info), GFP_KERNEL);
+ if (!fields)
+ return -ENOMEM;
+
+ #define COLLECT_FIELD(field) \
+ do { \
+ if (desc->field.width > 0) { \
+ fields[field_cnt].name = #field; \
+ fields[field_cnt].shift = desc->field.shift; \
+ fields[field_cnt].width = desc->field.width; \
+ fields[field_cnt].end = desc->field.shift + desc->field.width; \
+ field_cnt++; \
+ } \
+ } while (0)
+
+ /* same as struct config_reg_layout_desc filed except for pin_start and pin_cnt */
+ COLLECT_FIELD(debounce_width);
+ COLLECT_FIELD(drive_strength_2bit);
+ COLLECT_FIELD(drive_strength_3bit);
+ COLLECT_FIELD(function);
+ COLLECT_FIELD(input_enable);
+ COLLECT_FIELD(vsel);
+ COLLECT_FIELD(mode_select);
+ COLLECT_FIELD(open_drain_pull_up_sel);
+ COLLECT_FIELD(pull_down);
+ COLLECT_FIELD(pull_up);
+ COLLECT_FIELD(reserved);
+ COLLECT_FIELD(retention_signal_bus);
+ COLLECT_FIELD(schmitt_trigger_select);
+ COLLECT_FIELD(slew_rate);
+
+ #undef COLLECT_FIELD
+
+ sort(fields, field_cnt, sizeof(struct field_info), field_compare, NULL);
+
+ for (i = 0; i < field_cnt; i++) {
+ if (fields[i].end > 32) {
+ dev_err(dev,
+ "layout %d: field %s exceeds 32bit [shift=%u, width=%u, end=%u]\n",
+ index, fields[i].name,
+ fields[i].shift, fields[i].width, fields[i].end);
+ goto failed;
+ }
+
+ if (i < field_cnt - 1) {
+ if (fields[i].end > fields[i + 1].shift) {
+ dev_err(dev,
+ "layout %d: field overlap: %s[%u:%u] with %s[%u:%u]\n",
+ index, fields[i].name, fields[i].end - 1,
+ fields[i].shift, fields[i + 1].name,
+ fields[i + 1].end - 1, fields[i + 1].shift);
+ goto failed;
+ }
+ }
+ }
+
+ if (desc->reserved.width > 0) {
+ unsigned int used_mask = 0;
+ unsigned int reserved_mask = 0;
+
+ for (i = 0; i < field_cnt; i++) {
+ if (strcmp(fields[i].name, "reserved"))
+ used_mask |= GENMASK(fields[i].end - 1, fields[i].shift);
+ else
+ reserved_mask |= GENMASK(fields[i].end - 1, fields[i].shift);
+ }
+
+ if ((used_mask | reserved_mask) != 0xFFFFFFFF) {
+ dev_err(dev,
+ "layout %d: reserved field not cover all unused bits\n",
+ index);
+ dev_err(dev,
+ "used mask: 0x%08X, reserved mask: 0x%08X, combined: 0x%08X\n",
+ used_mask, reserved_mask, used_mask | reserved_mask);
+ }
+ }
+
+ kfree(fields);
+ return 0;
+
+failed:
+ kfree(fields);
+ return -EINVAL;
+}
+
+static int check_layout_pin_range(struct jhb100_pinctrl *sfp,
+ const struct config_reg_layout_desc *descs,
+ unsigned int num_desc)
+{
+ struct device *dev = sfp->gc.parent;
+
+ if (descs[num_desc - 1].pin_start + descs[num_desc - 1].pin_cnt > sfp->npins) {
+ dev_err(dev, "layout %u pin_start[%u] + pin_cnt[%u] exceeds pin number[%u]\n",
+ num_desc - 1, descs[num_desc - 1].pin_start,
+ descs[num_desc - 1].pin_cnt, sfp->npins);
+ return -EINVAL;
+ }
+
+ for (int i = 0; i < num_desc; i++) {
+ if (descs[i].pin_start == 0xff)
+ break;
+
+ if (i < num_desc - 1) {
+ if (descs[i].pin_start + descs[i].pin_cnt > descs[i + 1].pin_start) {
+ dev_err(dev, "pin range: [%u-%u] overlaps with [%u-%u]\n",
+ descs[i].pin_start, descs[i].pin_cnt,
+ descs[i + 1].pin_start, descs[i + 1].pin_cnt);
+ return -EINVAL;
+ }
+
+ if (descs[i].pin_start + descs[i].pin_cnt < descs[i + 1].pin_start) {
+ dev_err(dev, "pin range: [%u-%u] -> [%u-%u] has gap\n",
+ descs[i].pin_start, descs[i].pin_cnt,
+ descs[i + 1].pin_start, descs[i + 1].pin_cnt);
+ return -EINVAL;
+ }
+ }
+ }
+
+ return 0;
+}
+
+static int check_pinctrl_layouts(struct jhb100_pinctrl *sfp,
+ const struct config_reg_layout_desc *layouts)
+{
+ struct device *dev = sfp->gc.parent;
+ int i = 0, err_cnt = 0, ret;
+
+ if (!layouts) {
+ dev_err(dev, "layout pointer is NULL\n");
+ return -EINVAL;
+ }
+
+ while (layouts[i].pin_start != 0xff) {
+ ret = check_crl_desc(sfp, i, &layouts[i]);
+ if (ret) {
+ dev_err(dev, "layout %d check failed\n", i);
+ err_cnt++;
+ }
+
+ if (++i > 100) {
+ dev_err(dev, "too many layouts or missing 0xff for end\n");
+ return -EINVAL;
+ }
+ }
+
+ if (!err_cnt) {
+ ret = check_layout_pin_range(sfp, layouts, i);
+ if (ret)
+ err_cnt++;
+ }
+
+ if (err_cnt) {
+ dev_err(dev, "pinctrl layout check finish with %d error(s)\n", err_cnt);
+ return -EINVAL;
+ }
+
+ dev_info(dev, "pinctrl layout check completed!\n");
+ return 0;
+}
+
+static
+struct pinctrl_pin_desc *devm_create_pins_from_pld(struct device *dev,
+ const struct jhb100_pin_layout_desc *desc,
+ const char *prefix,
+ unsigned int *total_pins,
+ unsigned int *total_gpios,
+ int **gpio_func_sel_arr)
+{
+ struct pinctrl_pin_desc *pins = NULL;
+ unsigned int i, j, ngpios = 0, npins = 0, pin_index = 0;
+ unsigned int same_name_found = 0;
+ int *arr;
+
+ if (!dev || !desc || !prefix) {
+ dev_err(dev, "Invalid parameters: desc=%p, prefix=%s\n",
+ desc, prefix);
+ return ERR_PTR(-EINVAL);
+ }
+
+ for (i = 0; desc[i].pin_start != 0xff; i++) {
+ if (!desc[i].pin_cnt) {
+ dev_err(dev, "Invalid pin cnt\n");
+ return ERR_PTR(-EINVAL);
+ }
+
+ npins += desc[i].pin_cnt;
+ }
+
+ if (npins == 0) {
+ dev_err(dev, "No pins defined\n");
+ return ERR_PTR(-EINVAL);
+ }
+
+ dev_dbg(dev, "Total pins to create: %d\n", npins);
+
+ pins = devm_kcalloc(dev, npins, sizeof(*pins), GFP_KERNEL);
+ if (!pins)
+ return ERR_PTR(-ENOMEM);
+
+ arr = devm_kzalloc(dev, npins, GFP_KERNEL);
+ if (!arr)
+ return ERR_PTR(-ENOMEM);
+
+ for (i = 0; desc[i].pin_start != 0xff; i++) {
+ same_name_found = 0;
+
+ for (j = 0; j < i; j++) {
+ if (!strcmp(desc[j].name, desc[i].name)) {
+ same_name_found = 1;
+ break;
+ }
+ }
+
+ for (j = 0; j < desc[i].pin_cnt; j++) {
+ char *name = NULL;
+ int pin_num = desc[i].pin_start + j;
+
+ pins[pin_index].number = pin_num;
+ if (same_name_found) {
+ name = devm_kasprintf(dev, GFP_KERNEL, "%s_%s_%d",
+ prefix, desc[i].name,
+ desc[i].pin_start + j);
+ } else {
+ if (desc[i].pin_cnt > 1)
+ name = devm_kasprintf(dev, GFP_KERNEL, "%s_%s_%d",
+ prefix, desc[i].name, j);
+ else
+ name = devm_kasprintf(dev, GFP_KERNEL, "%s_%s",
+ prefix, desc[i].name);
+ }
+
+ if (!name) {
+ dev_err(dev, "Failed to allocate pin name for pin %d\n",
+ pin_num);
+ return ERR_PTR(-ENOMEM);
+ }
+
+ if (!strcmp(desc[i].name, "gpio") || desc[i].gpio_func_sel != -1)
+ ngpios++;
+
+ pins[pin_index].name = name;
+ arr[pin_index] = desc[i].gpio_func_sel;
+ pin_index++;
+ }
+ }
+
+ *total_pins = npins;
+ *total_gpios = ngpios;
+ *gpio_func_sel_arr = arr;
+
+ return pins;
+}
+
+static int of_pinvref_get(struct device *dev, const struct pinvref_desc *pv_desc, u32 *val)
+{
+ char prop_name[32];
+ struct device_node *np = dev->of_node;
+ int ret;
+
+ snprintf(prop_name, sizeof(prop_name), "%s-vref", pv_desc->name);
+ dev_dbg(dev, "Looking up %s from node %pOF\n", prop_name, np);
+
+ ret = of_property_read_u32(np, prop_name, val);
+ if (ret) {
+ dev_err(dev, "Looking up %s in node %pOF failed: %d\n", prop_name, np, ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int starfive_pinvref_set(struct device *dev, void __iomem *reg,
+ unsigned int val, const struct pinvref_desc *pv_desc)
+{
+ if (!pv_desc->range)
+ return 0;
+
+ if (pv_desc->range & BIT(val)) {
+ writel(val, reg);
+ } else {
+ dev_err(dev, "pin vref range is unsupported(%lx/%x)\n", BIT(val), pv_desc->range);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int starfive_pinvref_init(struct device *dev, void __iomem *base,
+ struct starfive_pinctrl_regs *pinctrl_regs)
+{
+ int ret = 0;
+ unsigned int val, i = 0;
+ struct pinvref_reg *vref;
+
+ vref = &pinctrl_regs->vref;
+ if (!vref->pv_desc)
+ return ret;
+
+ while (vref->pv_desc[i].name) {
+ ret = of_pinvref_get(dev, &vref->pv_desc[i], &val);
+ if (!ret)
+ ret = starfive_pinvref_set(dev, base + vref->reg + i * 4,
+ val, &vref->pv_desc[i]);
+ i++;
+ }
+
+ return ret;
+}
+
+int jhb100_pinctrl_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct gpio_irq_chip *girq;
+ const struct jhb100_pinctrl_domain_info *info;
+ struct jhb100_pinctrl *sfp;
+ struct pinctrl_desc *jhb100_pinctrl_desc;
+ struct reset_control *rst;
+ struct clk *clk;
+ int ret;
+
+ info = of_device_get_match_data(&pdev->dev);
+ if (!info)
+ return -ENODEV;
+
+ sfp = devm_kzalloc(dev, sizeof(*sfp), GFP_KERNEL);
+ if (!sfp)
+ return -ENOMEM;
+
+ sfp->base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(sfp->base))
+ return PTR_ERR(sfp->base);
+
+ clk = devm_clk_get_optional_enabled(dev, NULL);
+ if (IS_ERR(clk))
+ return dev_err_probe(dev, PTR_ERR(clk), "could not get & enable clock\n");
+
+ rst = devm_reset_control_array_get_optional_shared(dev);
+ if (IS_ERR(rst))
+ return dev_err_probe(dev, PTR_ERR(rst), "could not get reset control\n");
+
+ /*
+ * we don't want to assert reset and risk undoing pin muxing for the
+ * early boot serial console, but let's make sure the reset line is
+ * deasserted in case someone runs a really minimal bootloader.
+ */
+ ret = reset_control_deassert(rst);
+ if (ret)
+ return dev_err_probe(dev, ret, "could not deassert reset\n");
+
+ sfp->pins = devm_create_pins_from_pld(dev, info->pl_desc, info->name,
+ &sfp->npins, &sfp->ngpios,
+ &sfp->gpio_func_sel_arr);
+ if (IS_ERR(sfp->pins))
+ return PTR_ERR(sfp->pins);
+
+ jhb100_pinctrl_desc = devm_kzalloc(&pdev->dev,
+ sizeof(*jhb100_pinctrl_desc),
+ GFP_KERNEL);
+ if (!jhb100_pinctrl_desc)
+ return -ENOMEM;
+
+ jhb100_pinctrl_desc->name = dev_name(dev);
+ jhb100_pinctrl_desc->num_custom_params = ARRAY_SIZE(jhb100_custom_bindings);
+ jhb100_pinctrl_desc->custom_params = jhb100_custom_bindings;
+ jhb100_pinctrl_desc->pctlops = &jhb100_pinctrl_ops;
+ jhb100_pinctrl_desc->pmxops = &jhb100_pinmux_ops;
+ jhb100_pinctrl_desc->confops = &jhb100_pinconf_ops;
+ jhb100_pinctrl_desc->owner = THIS_MODULE;
+ jhb100_pinctrl_desc->pins = sfp->pins;
+ jhb100_pinctrl_desc->npins = sfp->npins;
+
+ sfp->info = info;
+ sfp->dev = dev;
+ platform_set_drvdata(pdev, sfp);
+ sfp->gc.parent = dev;
+ raw_spin_lock_init(&sfp->lock);
+ mutex_init(&sfp->mutex);
+
+ ret = devm_pinctrl_register_and_init(dev, jhb100_pinctrl_desc,
+ sfp, &sfp->pctl);
+ if (ret)
+ return dev_err_probe(dev, ret,
+ "could not register pinctrl driver\n");
+
+ sfp->gc.label = dev_name(dev);
+ sfp->gc.owner = THIS_MODULE;
+ sfp->gc.request = pinctrl_gpio_request;
+ sfp->gc.free = pinctrl_gpio_free;
+ sfp->gc.get_direction = jhb100_gpio_get_direction;
+ sfp->gc.direction_input = jhb100_gpio_direction_input;
+ sfp->gc.direction_output = jhb100_gpio_direction_output;
+ sfp->gc.get = jhb100_gpio_get;
+ sfp->gc.set = jhb100_gpio_set;
+ sfp->gc.set_config = gpiochip_generic_config;
+ sfp->gc.base = info->gc_base;
+ sfp->gc.ngpio = sfp->ngpios;
+
+ girq = &sfp->gc.irq;
+
+ if (info->regs->irq_edge.reg) {
+ gpio_irq_chip_set_chip(girq, &jhb100_irq_chip);
+ girq->parent_handler = jhb100_gpio_irq_handler;
+ girq->num_parents = 1;
+ girq->parents = devm_kcalloc(dev, girq->num_parents,
+ sizeof(*girq->parents),
+ GFP_KERNEL);
+ if (!girq->parents)
+ return -ENOMEM;
+
+ girq->default_type = IRQ_TYPE_NONE;
+ girq->handler = handle_bad_irq;
+ girq->init_hw = jhb100_gpio_init_hw;
+
+ ret = platform_get_irq(pdev, 0);
+ if (ret < 0)
+ return ret;
+
+ girq->parents[0] = ret;
+ }
+
+ ret = pinctrl_enable(sfp->pctl);
+ if (ret)
+ return ret;
+
+ if (sfp->gc.ngpio > 0) {
+ ret = devm_gpiochip_add_data(dev, &sfp->gc, sfp);
+ if (ret)
+ return dev_err_probe(dev, ret, "could not register gpiochip\n");
+
+ dev_info(dev, "StarFive JHB100 GPIO chip registered %d GPIOs\n",
+ sfp->gc.ngpio);
+ }
+
+ ret = check_pinctrl_layouts(sfp, info->crl_desc);
+ if (ret)
+ return ret;
+
+ ret = starfive_pinvref_init(dev, sfp->base, info->regs);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(jhb100_pinctrl_probe);
+
+MODULE_DESCRIPTION("Pinctrl driver for the StarFive JHB100 SoC");
+MODULE_AUTHOR("Alex Soo <yuklin.soo@starfivetech.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/pinctrl/starfive/pinctrl-starfive-jhb100.h b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100.h
new file mode 100644
index 000000000000..a5e7c788ba13
--- /dev/null
+++ b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100.h
@@ -0,0 +1,191 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Pinctrl / GPIO driver for StarFive JHB100 SoC
+ *
+ * Copyright (C) 2024 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <yuklin.soo@starfivetech.com>
+ *
+ */
+
+#ifndef __PINCTRL_STARFIVE_JHB100_H__
+#define __PINCTRL_STARFIVE_JHB100_H__
+
+#include <linux/gpio/driver.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinmux.h>
+
+#include "../core.h"
+
+#define PER2_GMAC_RGMII_FUNC 1
+#define PER2_GMAC_RMII_FUNC 2
+#define PER3_GMAC_RMII_FUNC 1
+
+/* mode select */
+#define JHB100_PUSH_PULL 0
+#define JHB100_OPEN_DRAIN 1
+#define JHB100_LEGACY_FAST_MODE_PLUS 2
+#define JHB100_LEGACY_FAST_MODE 3
+
+/* i2c open-drain pull-up select */
+#define JHB100_I2C_OPEN_DRAIN_PU_600_OHMS 0
+#define JHB100_I2C_OPEN_DRAIN_PU_900_OHMS 1
+#define JHB100_I2C_OPEN_DRAIN_PU_1200_OHMS 2
+#define JHB100_I2C_OPEN_DRAIN_PU_2000_OHMS 3
+
+struct jhb100_pin_layout_desc {
+ unsigned int pin_start;
+ unsigned int pin_cnt;
+ const char *name;
+ int gpio_func_sel;
+};
+
+struct jhb100_pinctrl {
+ struct device *dev;
+ struct gpio_chip gc;
+ struct pinctrl_gpio_range gpios;
+ raw_spinlock_t lock;
+ const char *iodomain_name;
+ void __iomem *base;
+ struct pinctrl_dev *pctl;
+ /* register read/write mutex */
+ struct mutex mutex;
+ const struct jhb100_pinctrl_domain_info *info;
+ /* wakeup */
+ int wakeup_gpio;
+ int wakeup_irq;
+ struct irq_domain *irq_domain;
+ const struct pinctrl_pin_desc *pins;
+ unsigned int npins;
+ unsigned int ngpios;
+ int *gpio_func_sel_arr;
+};
+
+/* pinref voltage range */
+#define JHB100_PINVREF_3_3V 0
+#define JHB100_PINVREF_2_5V 1
+#define JHB100_PINVREF_1_8V 2
+
+struct pinvref_desc {
+ const char *name;
+ unsigned int range;
+};
+
+struct pinvref_reg {
+ unsigned int reg;
+ const struct pinvref_desc *pv_desc;
+};
+
+struct gpio_irq_reg {
+ unsigned int reg;
+ unsigned int width_per_pin;
+};
+
+struct starfive_pinctrl_regs {
+ struct pinvref_reg vref;
+ struct gpio_irq_reg config;
+ struct gpio_irq_reg output;
+ struct gpio_irq_reg output_en;
+ struct gpio_irq_reg func_sel;
+ struct gpio_irq_reg gpio_status;
+ struct gpio_irq_reg irq_en;
+ struct gpio_irq_reg irq_status;
+ struct gpio_irq_reg irq_clr;
+ struct gpio_irq_reg irq_trigger;
+ struct gpio_irq_reg irq_level;
+ struct gpio_irq_reg irq_both_edge;
+ struct gpio_irq_reg irq_edge;
+};
+
+struct reg_layout_field {
+ unsigned char shift;
+ unsigned char width;
+ unsigned int func;
+};
+
+#define RL_DESC_SUPPORTED(crl_desc, field) ({ \
+ typeof(crl_desc) _desc = (crl_desc); \
+ (_desc && _desc->field.width > 0); \
+})
+
+#define RL_DESC_SHIFT(crl_desc, field) ({ \
+ typeof(crl_desc) __desc = (crl_desc); \
+ __desc->field.shift; \
+})
+
+#define RL_DESC_GENMASK(crl_desc, field) ({ \
+ typeof(crl_desc) __desc = (crl_desc); \
+ RL_DESC_SUPPORTED(__desc, field) ? \
+ GENMASK(__desc->field.shift + __desc->field.width - 1, __desc->field.shift) : 0; \
+})
+
+#define RL_DESC_SUPPORTED_FUNC(crl_desc, field, pinfunc) ({ \
+ typeof(crl_desc) _desc = (crl_desc); \
+ (_desc && _desc->field.width > 0 && \
+ (!_desc->field.func || (_desc->field.func & pinfunc))); \
+})
+
+struct config_reg_layout_desc {
+ unsigned int pin_start;
+ unsigned int pin_cnt;
+
+ struct reg_layout_field debounce_width;
+ struct reg_layout_field drive_strength_2bit;
+ struct reg_layout_field drive_strength_3bit;
+ struct reg_layout_field function;
+ struct reg_layout_field input_enable;
+ struct reg_layout_field vsel;
+ struct reg_layout_field mode_select;
+ struct reg_layout_field open_drain_pull_up_sel;
+ struct reg_layout_field pull_down;
+ struct reg_layout_field pull_up;
+ struct reg_layout_field reserved;
+ struct reg_layout_field retention_signal_bus;
+ struct reg_layout_field schmitt_trigger_select;
+ struct reg_layout_field slew_rate;
+};
+
+struct funcsel_reg_layout_desc {
+ unsigned int pin_start;
+ unsigned int pin_cnt;
+ unsigned int width;
+};
+
+struct jhb100_pinctrl_domain_info {
+ const char *name;
+ unsigned int gc_base;
+ const struct pinctrl_pin_desc *pins;
+ const struct jhb100_pin_layout_desc *pl_desc;
+ struct config_reg_layout_desc *crl_desc;
+ struct starfive_pinctrl_regs *regs;
+};
+
+static inline irq_hw_number_t pin_to_hwirq(struct jhb100_pinctrl *sfp)
+{
+ return sfp->wakeup_gpio - sfp->info->gc_base;
+}
+
+int jhb100_pinctrl_probe(struct platform_device *pdev);
+
+void pinctrl_utils_free_map(struct pinctrl_dev *pctldev,
+ struct pinctrl_map *map, unsigned int num_maps);
+int pinmux_generic_get_function_count(struct pinctrl_dev *pctldev);
+const char *pinmux_generic_get_function_name(struct pinctrl_dev *pctldev,
+ unsigned int selector);
+int pinmux_generic_get_function_groups(struct pinctrl_dev *pctldev,
+ unsigned int selector,
+ const char * const **groups,
+ unsigned int * const num_groups);
+int pinmux_generic_add_function(struct pinctrl_dev *pctldev,
+ const char *name,
+ const char * const *groups,
+ unsigned int const num_groups,
+ void *data);
+
+#if defined(CONFIG_GENERIC_PINCONF) && defined(CONFIG_OF)
+int pinconf_generic_parse_dt_config(struct device_node *np,
+ struct pinctrl_dev *pctldev,
+ unsigned long **configs,
+ unsigned int *nconfigs);
+#endif
+
+#endif /* __PINCTRL_STARFIVE_JHB100_H__ */
--
2.25.1
next prev parent reply other threads:[~2026-04-24 12:48 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-04-24 11:13 [PATCH v1 00/20] Add basic pinctrl drivers for JHB100 SoC Changhuang Liang
2026-04-24 11:13 ` [PATCH v1 01/20] dt-bindings: pinctrl: Add starfive,jhb100-sys0-pinctrl Changhuang Liang
2026-04-28 10:34 ` Linus Walleij
2026-04-24 11:13 ` Changhuang Liang [this message]
2026-04-28 10:29 ` [PATCH v1 02/20] pinctrl: starfive: Add StarFive JHB100 sys0 controller driver Linus Walleij
2026-04-24 11:13 ` [PATCH v1 03/20] dt-bindings: pinctrl: Add starfive,jhb100-sys0h-pinctrl Changhuang Liang
2026-04-24 11:13 ` [PATCH v1 04/20] pinctrl: starfive: Add StarFive JHB100 sys0h controller driver Changhuang Liang
2026-04-24 11:13 ` [PATCH v1 05/20] dt-bindings: pinctrl: Add starfive,jhb100-sys1-pinctrl Changhuang Liang
2026-04-24 11:13 ` [PATCH v1 06/20] pinctrl: starfive: Add StarFive JHB100 sys1 controller driver Changhuang Liang
2026-04-24 11:13 ` [PATCH v1 07/20] dt-bindings: pinctrl: Add starfive,jhb100-sys2-pinctrl Changhuang Liang
2026-04-25 10:28 ` Krzysztof Kozlowski
2026-04-24 11:13 ` [PATCH v1 08/20] pinctrl: starfive: Add StarFive JHB100 sys2 controller driver Changhuang Liang
2026-04-24 11:13 ` [PATCH v1 09/20] dt-bindings: pinctrl: Add starfive,jhb100-per0-pinctrl Changhuang Liang
2026-04-24 11:13 ` [PATCH v1 10/20] pinctrl: starfive: Add StarFive JHB100 per0 controller driver Changhuang Liang
2026-04-24 11:13 ` [PATCH v1 11/20] dt-bindings: pinctrl: Add starfive,jhb100-per1-pinctrl Changhuang Liang
2026-04-24 16:56 ` Conor Dooley
2026-04-28 1:28 ` Changhuang Liang
2026-04-28 18:51 ` Conor Dooley
2026-04-28 11:08 ` Linus Walleij
2026-04-24 11:13 ` [PATCH v1 12/20] pinctrl: starfive: Add StarFive JHB100 per1 controller driver Changhuang Liang
2026-04-24 11:13 ` [PATCH v1 13/20] dt-bindings: pinctrl: Add starfive,jhb100-per2-pinctrl Changhuang Liang
2026-04-24 13:17 ` Rob Herring (Arm)
2026-04-24 11:13 ` [PATCH v1 14/20] pinctrl: starfive: Add StarFive JHB100 per2 controller driver Changhuang Liang
2026-04-24 11:13 ` [PATCH v1 15/20] dt-bindings: pinctrl: Add starfive,jhb100-per2pok-pinctrl Changhuang Liang
2026-04-24 11:13 ` [PATCH v1 16/20] pinctrl: starfive: Add StarFive JHB100 per2pok controller driver Changhuang Liang
2026-04-24 11:13 ` [PATCH v1 17/20] dt-bindings: pinctrl: Add starfive,jhb100-per3-pinctrl Changhuang Liang
2026-04-24 11:13 ` [PATCH v1 18/20] pinctrl: starfive: Add StarFive JHB100 per3 controller driver Changhuang Liang
2026-04-24 11:13 ` [PATCH v1 19/20] riscv: dts: starfive: Add StarFive JHB100 pin function definitions Changhuang Liang
2026-04-24 17:00 ` Conor Dooley
2026-04-24 11:13 ` [PATCH v1 20/20] riscv: dts: starfive: jhb100: Add pinctrl nodes Changhuang Liang
2026-04-24 17:01 ` Conor Dooley
2026-04-28 1:53 ` Changhuang Liang
2026-04-28 10:11 ` [PATCH v1 00/20] Add basic pinctrl drivers for JHB100 SoC Linus Walleij
2026-04-29 0:53 ` Changhuang Liang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260424111330.702272-3-changhuang.liang@starfivetech.com \
--to=changhuang.liang@starfivetech.com \
--cc=alex@ghiti.fr \
--cc=aou@eecs.berkeley.edu \
--cc=brgl@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=kernel@esmil.dk \
--cc=krzk+dt@kernel.org \
--cc=lianfeng.ouyang@starfivetech.com \
--cc=linusw@kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=p.zabel@pengutronix.de \
--cc=palmer@dabbelt.com \
--cc=pjw@kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox