[PATCH v3 0/9] ARM: dts: aspeed: anacapa: restructure devicetree for development-phase

[PATCH v3 0/9] ARM: dts: aspeed: anacapa: restructure devicetree for development-phase

[Colin Huang via B4 Relay]

This series refactors the Anacapa BMC devicetree layout to better support
development-phase hardware revisions (EVT1/EVT2/DVT) while keeping a platform
entrypoint.

Signed-off-by: Colin Huang <u8813345@gmail.com>
---
Changes in v3:
- Restructure the EVT2 devicetree to inherit from the EVT1 devicetree, making it incremental rather than standalone.
- Add the DVT devicetree, inheriting from the EVT2 devicetree.
- Enable MCTP and FRU support for the NIC.
- Align PDB fan GPIO numbering.
- Add an EEPROM device node for the NFC adaptor board.
- Add an additional EEPROM device node for the SCM.
- Add shunt resistor values for HSC monitors
- Link to v2: https://lore.kernel.org/r/20260409-anacapa-devlop-phase-devicetree-v2-0-68f328671653@gmail.com

Changes in v2:
- Fix dtbs_check fail.
  Validated by following command:
    make dt_binding_check DT_SCHEMA_FILES=arm/aspeed/aspeed.yaml
    make CHECK_DTBS=y DT_SCHEMA_FILES=arm/aspeed/aspeed.yaml aspeed/aspeed-bmc-facebook-anacapa.dtb
    make CHECK_DTBS=y DT_SCHEMA_FILES=arm/aspeed/aspeed.yaml aspeed/aspeed-bmc-facebook-anacapa-evt1.dtb
    make CHECK_DTBS=y DT_SCHEMA_FILES=arm/aspeed/aspeed.yaml aspeed/aspeed-bmc-facebook-anacapa-evt2.dtb
- Link to v1: https://lore.kernel.org/r/20260407-anacapa-devlop-phase-devicetree-v1-0-97b96367cac3@gmail.com

---
Andy Chung (1):
      ARM: dts: aspeed: anacapa: Enable MCTP and FRU for NIC

Carl Lee (1):
      ARM: dts: aspeed: anacapa: Add eeprom device node for NFC adaptor board

Colin Huang (5):
      dt-bindings: arm: aspeed: add Anacapa EVT1 EVT2 DVT board
      ARM: dts: aspeed: anacapa: add EVT1 devicetree and point wrapper to it
      ARM: dts: aspeed: anacapa: add EVT2 devicetree inheriting EVT1
      ARM: dts: aspeed: anacapa: add DVT devicetree inheriting EVT2
      ARM: dts: aspeed: anacapa: add additional EEPROM node for SCM

Peter Shen (1):
      ARM: dts: aspeed: anacapa: evt2: add shunt resistor values for HSC monitors

Rex Fu (1):
      ARM: dts: aspeed: anacapa: Align PDB fan GPIO numbering

 .../devicetree/bindings/arm/aspeed/aspeed.yaml     |    3 +
 .../dts/aspeed/aspeed-bmc-facebook-anacapa-dvt.dts |  178 +++
 .../aspeed/aspeed-bmc-facebook-anacapa-evt1.dts    | 1179 ++++++++++++++++++++
 .../aspeed/aspeed-bmc-facebook-anacapa-evt2.dts    |  228 ++++
 .../dts/aspeed/aspeed-bmc-facebook-anacapa.dts     | 1077 +-----------------
 5 files changed, 1589 insertions(+), 1076 deletions(-)
---
base-commit: 7ca1caf017d34396397b19fb4de9ecef256f4acc
change-id: 20260407-anacapa-devlop-phase-devicetree-4101d3f312c0

Best regards,
-- 
Colin Huang <u8813345@gmail.com>

[PATCH v3 1/9] dt-bindings: arm: aspeed: add Anacapa EVT1 EVT2 DVT board

[Colin Huang via B4 Relay]

From: Colin Huang <u8813345@gmail.com>

Document Anacapa BMC EVT1, EVT2, and DVT compatibles.

Signed-off-by: Colin Huang <u8813345@gmail.com>
---
 Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
index 9ba195b8f22d..d3e9d9a2f881 100644
--- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
+++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
@@ -84,6 +84,9 @@ properties:
               - asus,ast2600-kommando-ipmi-card
               - asus,x4tf-bmc
               - facebook,anacapa-bmc
+              - facebook,anacapa-bmc-evt1
+              - facebook,anacapa-bmc-evt2
+              - facebook,anacapa-bmc-dvt
               - facebook,bletchley-bmc
               - facebook,catalina-bmc
               - facebook,clemente-bmc

-- 
2.34.1

[PATCH v3 2/9] ARM: dts: aspeed: anacapa: add EVT1 devicetree and point wrapper to it

[Colin Huang via B4 Relay]

From: Colin Huang <u8813345@gmail.com>

This change introduces a development-phase devicetree for the
Facebook Anacapa BMC EVT1 hardware revision and updates the Anacapa
wrapper DTS to reference it.

A dedicated EVT1 DTS is added for revision-specific hardware while
keeping a single, Anacapa entrypoint used by the build and deployment
flow. The top-level aspeed-bmc-facebook-anacapa.dts

Signed-off-by: Colin Huang <u8813345@gmail.com>
---
 .../aspeed/aspeed-bmc-facebook-anacapa-evt1.dts    | 1103 ++++++++++++++++++++
 .../dts/aspeed/aspeed-bmc-facebook-anacapa.dts     | 1077 +------------------
 2 files changed, 1104 insertions(+), 1076 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts
new file mode 100644
index 000000000000..9314ee493c61
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts
@@ -0,0 +1,1103 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+/dts-v1/;
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+	model = "Facebook Anacapa BMC";
+	compatible = "facebook,anacapa-bmc-evt1", "aspeed,ast2600";
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		serial4 = &uart5;
+		i2c16 = &i2c0mux0ch0;
+		i2c17 = &i2c0mux0ch1;
+		i2c18 = &i2c0mux0ch2;
+		i2c19 = &i2c0mux0ch3;
+		i2c20 = &i2c1mux0ch0;
+		i2c21 = &i2c1mux0ch1;
+		i2c22 = &i2c1mux0ch2;
+		i2c23 = &i2c1mux0ch3;
+		i2c24 = &i2c4mux0ch0;
+		i2c25 = &i2c4mux0ch1;
+		i2c26 = &i2c4mux0ch2;
+		i2c27 = &i2c4mux0ch3;
+		i2c28 = &i2c4mux0ch4;
+		i2c29 = &i2c4mux0ch5;
+		i2c30 = &i2c4mux0ch6;
+		i2c31 = &i2c4mux0ch7;
+		i2c32 = &i2c8mux0ch0;
+		i2c33 = &i2c8mux0ch1;
+		i2c34 = &i2c8mux0ch2;
+		i2c35 = &i2c8mux0ch3;
+		i2c36 = &i2c10mux0ch0;
+		i2c37 = &i2c10mux0ch1;
+		i2c38 = &i2c10mux0ch2;
+		i2c39 = &i2c10mux0ch3;
+		i2c40 = &i2c10mux0ch4;
+		i2c41 = &i2c10mux0ch5;
+		i2c42 = &i2c10mux0ch6;
+		i2c43 = &i2c10mux0ch7;
+		i2c44 = &i2c11mux0ch0;
+		i2c45 = &i2c11mux0ch1;
+		i2c46 = &i2c11mux0ch2;
+		i2c47 = &i2c11mux0ch3;
+		i2c48 = &i2c11mux0ch4;
+		i2c49 = &i2c11mux0ch5;
+		i2c50 = &i2c11mux0ch6;
+		i2c51 = &i2c11mux0ch7;
+		i2c52 = &i2c13mux0ch0;
+		i2c53 = &i2c13mux0ch1;
+		i2c54 = &i2c13mux0ch2;
+		i2c55 = &i2c13mux0ch3;
+		i2c56 = &i2c13mux0ch4;
+		i2c57 = &i2c13mux0ch5;
+		i2c58 = &i2c13mux0ch6;
+		i2c59 = &i2c13mux0ch7;
+	};
+
+	chosen {
+		stdout-path = "serial4:57600n8";
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+				  <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+				  <&adc1 2>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "bmc_heartbeat_amber";
+			gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-1 {
+			label = "fp_id_amber";
+			default-state = "off";
+			gpios = <&gpio0 ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		video_engine_memory: video {
+			size = <0x02c00000>;
+			alignment = <0x00100000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	p3v3_bmc_aux: regulator-p3v3-bmc-aux {
+		compatible = "regulator-fixed";
+		regulator-name = "p3v3_bmc_aux";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	spi_gpio: spi {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sck-gpios = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+		status = "okay";
+
+		tpm@0 {
+			compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+			spi-max-frequency = <33000000>;
+			reg = <0>;
+		};
+	};
+};
+
+&adc0 {
+	aspeed,int-vref-microvolt = <2500000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+	status = "okay";
+};
+
+&adc1 {
+	aspeed,int-vref-microvolt = <2500000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc10_default>;
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&fmc {
+	status = "okay";
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&gfx {
+	status = "okay";
+	memory-region = <&gfx_memory>;
+};
+
+&gpio0 {
+	gpio-line-names =
+
+	/*A0-A7*/
+	"","","","","","","","",
+
+	/*B0-B7*/
+	"BATTERY_DETECT", "", "", "BMC_READY",
+	"", "FM_ID_LED", "", "",
+
+	/*C0-C7*/
+	"","","","","","","","",
+
+	/*D0-D7*/
+	"","","","","","","","",
+
+	/*E0-E7*/
+	"","","","","","","","",
+
+	/*F0-F7*/
+	"","","","","","","","",
+
+	/*G0-G7*/
+	"FM_MUX1_SEL", "", "", "",
+	"", "", "FM_DEBUG_PORT_PRSNT_N", "FM_BMC_DBP_PRESENT_N",
+
+	/*H0-H7*/
+	"","","","","","","","",
+
+	/*I0-I7*/
+	"", "", "", "",
+	"", "FLASH_WP_STATUS", "BMC_JTAG_MUX_SEL", "",
+
+	/*J0-J7*/
+	"","","","","","","","",
+
+	/*K0-K7*/
+	"","","","","","","","",
+
+	/*L0-L7*/
+	"","","","","","","","",
+
+	/*M0-M7*/
+	"", "BMC_FRU_WP", "", "",
+	"", "", "", "",
+
+	/*N0-N7*/
+	"LED_POSTCODE_0", "LED_POSTCODE_1", "LED_POSTCODE_2", "LED_POSTCODE_3",
+	"LED_POSTCODE_4", "LED_POSTCODE_5", "LED_POSTCODE_6", "LED_POSTCODE_7",
+
+	/*O0-O7*/
+	"","","","","","","","",
+
+	/*P0-P7*/
+	"PWR_BTN_BMC_BUF_N", "", "ID_RST_BTN_BMC_N", "",
+	"PWR_LED", "", "", "BMC_HEARTBEAT_N",
+
+	/*Q0-Q7*/
+	"","","","","","","","",
+
+	/*R0-R7*/
+	"","","","","","","","",
+
+	/*S0-S7*/
+	"", "", "SYS_BMC_PWRBTN_N", "",
+	"", "", "", "RUN_POWER_FAULT",
+
+	/*T0-T7*/
+	"","","","","","","","",
+
+	/*U0-U7*/
+	"","","","","","","","",
+
+	/*V0-V7*/
+	"","","","","","","","",
+
+	/*W0-W7*/
+	"","","","","","","","",
+
+	/*X0-X7*/
+	"","","","","","","","",
+
+	/*Y0-Y7*/
+	"","","","","","","","",
+
+	/*Z0-Z7*/
+	"SPI_BMC_TPM_CS2_N", "", "", "SPI_BMC_TPM_CLK",
+	"SPI_BMC_TPM_MOSI", "SPI_BMC_TPM_MISO", "", "";
+};
+
+&gpio1 {
+	gpio-line-names =
+	/*18A0-18A7*/
+	"","","","","","","","",
+
+	/*18B0-18B7*/
+	"","","","",
+	"FM_BOARD_BMC_REV_ID0", "FM_BOARD_BMC_REV_ID1",
+	"FM_BOARD_BMC_REV_ID2", "",
+
+	/*18C0-18C7*/
+	"","","","","","","","",
+
+	/*18D0-18D7*/
+	"","","","","","","","",
+
+	/*18E0-18E3*/
+	"FM_BMC_PROT_LS_EN", "AC_PWR_BMC_BTN_N", "", "";
+};
+
+// L Bridge Board
+&i2c0 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c2048";
+		reg = <0x50>;
+		pagesize = <128>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c0mux0ch0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c0mux0ch1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c0mux0ch2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c0mux0ch3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+// R Bridge Board
+&i2c1 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c2048";
+		reg = <0x50>;
+		pagesize = <128>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c1mux0ch0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c1mux0ch1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c1mux0ch2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c1mux0ch3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+// MB - E1.S
+&i2c4 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c4mux0ch0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c4mux0ch1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c4mux0ch2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c4mux0ch3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c4mux0ch4: i2c@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c4mux0ch5: i2c@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c4mux0ch6: i2c@6 {
+			reg = <6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c4mux0ch7: i2c@7 {
+			reg = <7>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+// AMC
+&i2c5 {
+	status = "okay";
+};
+
+// MB
+&i2c6 {
+	status = "okay";
+
+	// HPM FRU
+	eeprom@50 {
+		compatible = "atmel,24c256";
+		reg = <0x50>;
+	};
+};
+
+// SCM
+&i2c7 {
+	status = "okay";
+
+
+};
+
+// MB - PDB
+&i2c8 {
+	status = "okay";
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9546";
+		reg = <0x72>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c8mux0ch0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			adc@1f {
+				compatible = "ti,adc128d818";
+				reg = <0x1f>;
+				ti,mode = /bits/ 8 <1>;
+			};
+
+			gpio@22 {
+				compatible = "nxp,pca9555";
+				reg = <0x22>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <174 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+					"RPDB_FAN_FULL_SPEED_R_N", "RPDB_I2C_TEMP75_U8_ALERT_R_N",
+					"RPDB_I2C_TMP432_U29_ALERT_R_N", "RPDB_GLOBAL_WP",
+					"RPDB_FAN_CT_FAN_FAIL_R_N", "",
+					"", "",
+					"RPDB_ALERT_P50V_HSC2_R_N", "RPDB_ALERT_P50V_HSC3_R_N",
+					"RPDB_ALERT_P50V_HSC4_R_N", "RPDB_ALERT_P50V_STBY_R_N",
+					"RPDB_I2C_P12V_MB_VRM_ALERT_R_N",
+					"RPDB_I2C_P12V_STBY_VRM_ALERT_R_N",
+					"RPDB_PGD_P3V3_STBY_PWRGD_R",
+					"RPDB_P12V_STBY_VRM_PWRGD_BUF_R";
+			};
+
+			gpio@24 {
+				compatible = "nxp,pca9555";
+				reg = <0x24>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <174 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+					"RPDB_EAM2_PRSNT_MOS_N_R", "RPDB_EAM3_PRSNT_MOS_N_R",
+					"RPDB_PWRGD_P50V_HSC4_SYS_R",
+					"RPDB_PWRGD_P50V_STBY_SYS_BUF_R",
+					"RPDB_P50V_FAN1_R2_PG", "RPDB_P50V_FAN2_R2_PG",
+					"RPDB_P50V_FAN3_R2_PG", "RPDB_P50V_FAN4_R2_PG",
+					"", "RPDB_FAN1_PRSNT_N_R",
+					"", "RPDB_FAN2_PRSNT_N_R",
+					"RPDB_FAN3_PRSNT_N_R", "RPDB_FAN4_PRSNT_N_R",
+					"", "";
+			};
+
+			// R-PDB FRU
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+		};
+		i2c8mux0ch1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpio@22 {
+				compatible = "nxp,pca9555";
+				reg = <0x22>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <174 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+					"LPDB_FAN_FULL_SPEED_R_N","LPDB_I2C_TEMP75_U8_ALERT_R_N",
+					"LPDB_I2C_TMP432_U29_ALERT_R_N","LPDB_GLOBAL_WP",
+					"LPDB_FAN_CT_FAN_FAIL_R_N","",
+					"","",
+					"LPDB_ALERT_P50V_HSC0_R_N","LPDB_ALERT_P50V_HSC1_R_N",
+					"LPDB_ALERT_P50V_HSC5_R_N","LPDB_I2C_P12V_SW_VRM_ALERT_R_N",
+					"LPDB_EAM0_PRSNT_MOS_N_R","LPDB_EAM1_PRSNT_MOS_N_R",
+					"LPDB_PWRGD_P50V_HSC5_SYS_R","";
+			};
+
+			gpio@24 {
+				compatible = "nxp,pca9555";
+				reg = <0x24>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <174 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+					"LPDB_P50V_FAN1_R2_PG","LPDB_P50V_FAN2_R2_PG",
+					"LPDB_P50V_FAN3_R2_PG","LPDB_P50V_FAN4_R2_PG",
+					"LPDB_P50V_FAN5_R2_PG","LPDB_FAN1_PRSNT_N_R",
+					"LPDB_FAN2_PRSNT_N_R","LPDB_FAN3_PRSNT_N_R",
+					"LPDB_FAN4_PRSNT_N_R","LPDB_FAN5_PRSNT_N_R",
+					"","",
+					"","",
+					"","";
+			};
+
+			// L-PDB FRU
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+		};
+		i2c8mux0ch2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c8mux0ch3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+// SCM
+&i2c9 {
+	status = "okay";
+
+	// SCM FRU
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	// BSM FRU
+	eeprom@56 {
+		compatible = "atmel,24c64";
+		reg = <0x56>;
+	};
+};
+
+// R Bridge Board
+&i2c10 {
+	status = "okay";
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9548";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c10mux0ch0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c10mux0ch1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c10mux0ch2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c10mux0ch3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c10mux0ch4: i2c@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c10mux0ch5: i2c@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpio@22 {
+				compatible = "nxp,pca9555";
+				reg = <0x22>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				gpio-line-names =
+					"","",
+					"","RBB_CPLD_REFRESH_IN_PRGRS_R_L",
+					"RBB_EAM0_NIC_CBL_PRSNT_R_L","RBB_EAM1_NIC_CBL_PRSNT_R_L",
+					"RBB_AINIC_JTAG_MUX_R2_SEL","RBB_SPI_MUX0_R2_SEL",
+					"RBB_AINIC_PRSNT_R_L","RBB_AINIC_OE_R_N",
+					"RBB_AINIC_BOARD_R2_ID","RBB_RST_USB2_HUB_R_N",
+					"RBB_RST_FT4222_R_N","RBB_RST_MCP2210_R_N",
+					"","";
+			};
+
+			// R Bridge Board FRU
+			eeprom@52 {
+				compatible = "atmel,24c256";
+				reg = <0x52>;
+			};
+		};
+		i2c10mux0ch6: i2c@6 {
+			reg = <6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c10mux0ch7: i2c@7 {
+			reg = <7>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+// L Bridge Board
+&i2c11 {
+	status = "okay";
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9548";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c11mux0ch0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c11mux0ch1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c11mux0ch2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c11mux0ch3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c11mux0ch4: i2c@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c11mux0ch5: i2c@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpio@22 {
+				compatible = "nxp,pca9555";
+				reg = <0x22>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				gpio-line-names =
+					"","",
+					"","LBB_CPLD_REFRESH_IN_PRGRS_R_L",
+					"LBB_EAM0_NIC_CBL_PRSNT_R_L","LBB_EAM1_NIC_CBL_PRSNT_R_L",
+					"LBB_AINIC_JTAG_MUX_R2_SEL","LBB_SPI_MUX0_R2_SEL",
+					"LBB_AINIC_PRSNT_R_L","LBB_AINIC_OE_R_N",
+					"LBB_AINIC_BOARD_R2_ID","LBB_RST_USB2_HUB_R_N",
+					"LBB_RST_FT4222_R_N","LBB_RST_MCP2210_R_N",
+					"","";
+			};
+
+			// L Bridge Board FRU
+			eeprom@52 {
+				compatible = "atmel,24c256";
+				reg = <0x52>;
+			};
+		};
+		i2c11mux0ch6: i2c@6 {
+			reg = <6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c11mux0ch7: i2c@7 {
+			reg = <7>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+// Debug Card
+&i2c12 {
+	status = "okay";
+};
+
+// MB
+&i2c13 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c13mux0ch0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c13mux0ch1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c13mux0ch2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c13mux0ch3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			adc@1f {
+				compatible = "ti,adc128d818";
+				reg = <0x1f>;
+				ti,mode = /bits/ 8 <1>;
+			};
+		};
+		i2c13mux0ch4: i2c@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			// HPM BRD ID FRU
+			eeprom@51 {
+				compatible = "atmel,24c256";
+				reg = <0x51>;
+			};
+		};
+		i2c13mux0ch5: i2c@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c13mux0ch6: i2c@6 {
+			reg = <6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c13mux0ch7: i2c@7 {
+			reg = <7>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			nfc@28 {
+				compatible = "nxp,nxp-nci-i2c";
+				reg = <0x28>;
+
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <156 IRQ_TYPE_LEVEL_HIGH>;
+
+				enable-gpios = <&sgpiom0 241 GPIO_ACTIVE_HIGH>;
+			};
+		};
+	};
+};
+
+// SCM
+&i2c14 {
+	status = "okay";
+};
+
+&i2c15 {
+	status = "okay";
+};
+
+&kcs2 {
+	aspeed,lpc-io-reg = <0xca8>;
+	status = "okay";
+};
+
+&kcs3 {
+	aspeed,lpc-io-reg = <0xca2>;
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ncsi3_default>;
+	use-ncsi;
+};
+
+&sgpiom0 {
+	ngpios = <128>;
+	bus-frequency = <2000000>;
+	gpio-line-names =
+	/*in - out */
+	/* A0-A7 line 0-15 */
+	"L_FNIC_FLT", "FM_CPU0_SYS_RESET_N",
+	"L_BNIC0_FLT", "CPU0_KBRST_N",
+	"L_BNIC1_FLT", "FM_CPU0_PROCHOT_trigger_N",
+	"L_BNIC2_FLT", "FM_CLR_CMOS_R_P0",
+	"L_BNIC3_FLT", "Force_I3C_SEL",
+	"L_RTM_SW_FLT", "SYSTEM_Force_Run_AC_Cycle",
+	"", "",
+	"", "",
+
+	/* B0-B7 line 16-31 */
+	"Channel0_leakage_EAM3", "FM_CPU_FPGA_JTAG_MUX_SEL",
+	"Channel1_leakage_EAM0", "FM_SCM_JTAG_MUX_SEL",
+	"Channel2_leakage_Manifold1", "FM_BRIDGE_JTAG_MUX_SEL",
+	"Channel5_leakage_present_EAM1", "FM_CPU0_NMI_SYNC_FLOOD_N",
+	"Channel4_leakage_Manifold2", "",
+	"Channel5_leakage_EAM1", "",
+	"Channel6_leakage_CPU_DIMM", "",
+	"Channel7_leakage_EAM2", "",
+
+	/* C0-C7 line 32-47 */
+	"RSVD_RMC_GPIO3", "",
+	"LEAK_DETECT_RMC_N", "",
+	"HDR_P0_NMI_BTN_BUF_R_N", "",
+	"Channel6_leakage_present_CPU_DIMM", "",
+	"", "",
+	"", "",
+	"", "",
+	"", "",
+
+	/* D0-D7 line 48-63 */
+	"Channel0_leakage_present_EAM3", "",
+	"Channel1_leakage_present_EAM0", "",
+	"Channel2_leakage_present_Manifold1", "",
+	"Channel4_leakage_present_Manifold2", "",
+	"AMC_BRD_PRSNT_CPLD_L", "",
+	"Channel7_leakage_present_EAM2", "",
+	"", "",
+	"", "",
+
+	/* E0-E7 line 64-79 */
+	"L_PRSNT_B_FENIC_R2_N", "",
+	"L_PRSNT_B_BENIC0_R2_N", "",
+	"L_PRSNT_B_BENIC1_R2_N", "",
+	"L_PRSNT_B_BENIC2_R2_N", "",
+	"L_PRSNT_B_BENIC3_R2_N", "",
+	"", "",
+	"", "",
+	"", "",
+
+	/* F0-F7 line 80-95 */
+	"R_PRSNT_B_FENIC_R2_N", "SGPIO_READY",
+	"R_PRSNT_B_BENIC0_R2_N", "",
+	"R_PRSNT_B_BENIC1_R2_N", "",
+	"R_PRSNT_B_BENIC2_R2_N", "",
+	"R_PRSNT_B_BENIC3_R2_N", "",
+	"", "",
+	"", "",
+	"", "",
+
+	/* G0-G7 line 96-111 */
+	"L_PRSNT_EDSFF0_N", "",
+	"L_PRSNT_EDSFF1_N", "",
+	"R_PRSNT_EDSFF2_N", "",
+	"R_PRSNT_EDSFF3_N", "",
+	"HPM_EDSFF_PG", "",
+	"", "",
+	"", "FM_BMC_READY_PLD",
+	"", "",
+
+	/* H0-H7 line 112-127 */
+	"R_FNIC_FLT", "",
+	"R_BNIC0_FLT", "",
+	"R_BNIC1_FLT", "",
+	"R_BNIC2_FLT", "",
+	"R_BNIC3_FLT", "",
+	"R_RTM_SW_FLT", "",
+	"", "",
+	"", "",
+
+	/* I0-I7 line 128-143 */
+	"EAM0_BRD_PRSNT_R_L", "",
+	"EAM1_BRD_PRSNT_R_L", "",
+	"EAM2_BRD_PRSNT_R_L", "",
+	"EAM3_BRD_PRSNT_R_L", "",
+	"FM_TPM_PRSNT_R_N", "",
+	"PDB_L_PRSNT_R_N", "",
+	"PRSNT_EDSFF_BOOT_N", "",
+	"PRSNT_CPU0_N", "",
+
+	/* J0-J7 line 144-159 */
+	"PRSNT_L_BRIDGE_R", "",
+	"PRSNT_R_BRIDGE_R", "",
+	"BRIDGE_L_MAIN_PG_R", "",
+	"BRIDGE_R_MAIN_PG_R", "",
+	"BRIDGE_L_STBY_PG_R", "",
+	"BRIDGE_R_STBY_PG_R", "",
+	"", "",
+	"", "",
+
+	/* K0-K7 line 160-175 */
+	"ADC_I2C_ALERT_N", "",
+	"TEMP_I2C_ALERT_R_L", "",
+	"CPU0_VR_SMB_ALERT_CPLD_N", "",
+	"COVER_INTRUDER_R_N", "",
+	"HANDLE_INTRUDER_CPLD_N", "",
+	"IRQ_MCIO_CPLD_WAKE_R_N", "",
+	"APML_CPU0_ALERT_R_N", "",
+	"PDB_ALERT_R_N", "",
+
+	/* L0-L7 line 176-191 */
+	"L_EDSFF0_PG", "",
+	"L_EDSFF1_PG", "",
+	"R_EDSFF2_PG", "",
+	"R_EDSFF3_PG", "",
+	"HPM_CPLD_HEART_BIT", "",
+	"RBB_CPLD_HEART_BIT", "",
+	"LBB_CPLD_HEART_BIT", "",
+	"FM_BIOS_POST_CMPLT_R_N", "",
+
+	/* M0-M7 line 192-207 */
+	"EAM0_SMERR_CPLD_R_L", "",
+	"EAM1_SMERR_CPLD_R_L", "",
+	"EAM2_SMERR_CPLD_R_L", "",
+	"EAM3_SMERR_CPLD_R_L", "",
+	"CPU0_SMERR_N_R", "",
+	"CPU0_NV_SAVE_N_R", "",
+	"PDB_PWR_LOSS_CPLD_N", "",
+	"IRQ_BMC_SMI_ACTIVE_R_N", "",
+
+	/* N0-N7 line 208-223 */
+	"AMCROT_BMC_S5_RDY_R", "",
+	"AMC_RDY_R", "",
+	"AMC_STBY_PGOOD_R", "",
+	"CPU_AMC_SLP_S5_R_L", "",
+	"AMC_CPU_EAMPG_R", "",
+	"DIMM_PMIC_PG_TIMEOUT", "",
+	"", "",
+	"", "",
+
+	/* O0-O7 line 224-239 */
+	"HPM_PWR_FAIL", "Port80_b0",
+	"FM_DIMM_IP_FAIL", "Port80_b1",
+	"FM_DIMM_AH_FAIL", "Port80_b2",
+	"AMC_THERMTRIP_ASSERT", "Port80_b3",
+	"CPU_THERMTRIP_ASSERT", "Port80_b4",
+	"PVDDCR_SOC_P0_OCP_L", "Port80_b5",
+	"CPLD_SGPIO_RDY", "Port80_b6",
+	"FM_MAIN_PWREN_RMC_EN_ISO", "Port80_b7",
+
+	/* P0-P7 line 240-255 */
+	"CPU0_SLP_S5_N_R", "NFC_VEN",
+	"CPU0_SLP_S3_N_R", "",
+	"FM_CPU0_PWRGD", "",
+	"PWRGD_RMC", "",
+	"FM_RST_CPU0_RESET_N", "",
+	"FM_PWRGD_CPU0_PWROK", "",
+	"AMC_FAIL", "",
+	"S0_ON", "";
+
+	status = "okay";
+};
+
+// BIOS Flash
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi2_default>;
+	status = "okay";
+	reg = <0x1e631000 0xc4>, <0x50000000 0x8000000>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		label = "pnor";
+		spi-max-frequency = <12000000>;
+		spi-tx-bus-width = <2>;
+		spi-rx-bus-width = <2>;
+		status = "okay";
+	};
+};
+
+// HOST BIOS Debug
+&uart1 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+// BMC Debug Console
+&uart5 {
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+	pinctrl-names = "default";
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&wdt1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+	aspeed,reset-type = "soc";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+	aspeed,ext-pulse-duration = <256>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa.dts
index 1fddf3a5d138..209eef65cedb 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa.dts
@@ -1,1079 +1,4 @@
 // SPDX-License-Identifier: GPL-2.0-or-later
 
-/dts-v1/;
-#include "aspeed-g6.dtsi"
-#include <dt-bindings/gpio/aspeed-gpio.h>
-#include <dt-bindings/i2c/i2c.h>
+#include "aspeed-bmc-facebook-anacapa-evt1.dts"
 
-/ {
-	model = "Facebook Anacapa BMC";
-	compatible = "facebook,anacapa-bmc", "aspeed,ast2600";
-
-	aliases {
-		serial0 = &uart1;
-		serial1 = &uart2;
-		serial2 = &uart3;
-		serial3 = &uart4;
-		serial4 = &uart5;
-		i2c16 = &i2c0mux0ch0;
-		i2c17 = &i2c0mux0ch1;
-		i2c18 = &i2c0mux0ch2;
-		i2c19 = &i2c0mux0ch3;
-		i2c20 = &i2c1mux0ch0;
-		i2c21 = &i2c1mux0ch1;
-		i2c22 = &i2c1mux0ch2;
-		i2c23 = &i2c1mux0ch3;
-		i2c24 = &i2c4mux0ch0;
-		i2c25 = &i2c4mux0ch1;
-		i2c26 = &i2c4mux0ch2;
-		i2c27 = &i2c4mux0ch3;
-		i2c28 = &i2c4mux0ch4;
-		i2c29 = &i2c4mux0ch5;
-		i2c30 = &i2c4mux0ch6;
-		i2c31 = &i2c4mux0ch7;
-		i2c32 = &i2c8mux0ch0;
-		i2c33 = &i2c8mux0ch1;
-		i2c34 = &i2c8mux0ch2;
-		i2c35 = &i2c8mux0ch3;
-		i2c36 = &i2c10mux0ch0;
-		i2c37 = &i2c10mux0ch1;
-		i2c38 = &i2c10mux0ch2;
-		i2c39 = &i2c10mux0ch3;
-		i2c40 = &i2c10mux0ch4;
-		i2c41 = &i2c10mux0ch5;
-		i2c42 = &i2c10mux0ch6;
-		i2c43 = &i2c10mux0ch7;
-		i2c44 = &i2c11mux0ch0;
-		i2c45 = &i2c11mux0ch1;
-		i2c46 = &i2c11mux0ch2;
-		i2c47 = &i2c11mux0ch3;
-		i2c48 = &i2c11mux0ch4;
-		i2c49 = &i2c11mux0ch5;
-		i2c50 = &i2c11mux0ch6;
-		i2c51 = &i2c11mux0ch7;
-		i2c52 = &i2c13mux0ch0;
-		i2c53 = &i2c13mux0ch1;
-		i2c54 = &i2c13mux0ch2;
-		i2c55 = &i2c13mux0ch3;
-		i2c56 = &i2c13mux0ch4;
-		i2c57 = &i2c13mux0ch5;
-		i2c58 = &i2c13mux0ch6;
-		i2c59 = &i2c13mux0ch7;
-	};
-
-	chosen {
-		stdout-path = "serial4:57600n8";
-	};
-
-	iio-hwmon {
-		compatible = "iio-hwmon";
-		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
-				  <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
-				  <&adc1 2>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		led-0 {
-			label = "bmc_heartbeat_amber";
-			gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "heartbeat";
-		};
-
-		led-1 {
-			label = "fp_id_amber";
-			default-state = "off";
-			gpios = <&gpio0 ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
-		};
-	};
-
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x80000000>;
-	};
-
-	reserved-memory {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		video_engine_memory: video {
-			size = <0x02c00000>;
-			alignment = <0x00100000>;
-			compatible = "shared-dma-pool";
-			reusable;
-		};
-
-		gfx_memory: framebuffer {
-			size = <0x01000000>;
-			alignment = <0x01000000>;
-			compatible = "shared-dma-pool";
-			reusable;
-		};
-	};
-
-	p3v3_bmc_aux: regulator-p3v3-bmc-aux {
-		compatible = "regulator-fixed";
-		regulator-name = "p3v3_bmc_aux";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	spi_gpio: spi {
-		compatible = "spi-gpio";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		sck-gpios = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
-		mosi-gpios = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
-		miso-gpios = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>;
-		cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
-		num-chipselects = <1>;
-		status = "okay";
-
-		tpm@0 {
-			compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
-			spi-max-frequency = <33000000>;
-			reg = <0>;
-		};
-	};
-};
-
-&adc0 {
-	aspeed,int-vref-microvolt = <2500000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
-		&pinctrl_adc2_default &pinctrl_adc3_default
-		&pinctrl_adc4_default &pinctrl_adc5_default
-		&pinctrl_adc6_default &pinctrl_adc7_default>;
-	status = "okay";
-};
-
-&adc1 {
-	aspeed,int-vref-microvolt = <2500000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_adc10_default>;
-	status = "okay";
-};
-
-&ehci1 {
-	status = "okay";
-};
-
-&fmc {
-	status = "okay";
-
-	flash@0 {
-		status = "okay";
-		m25p,fast-read;
-		label = "bmc";
-		spi-max-frequency = <50000000>;
-#include "openbmc-flash-layout-128.dtsi"
-	};
-
-	flash@1 {
-		status = "okay";
-		m25p,fast-read;
-		label = "alt-bmc";
-		spi-max-frequency = <50000000>;
-	};
-};
-
-&gfx {
-	status = "okay";
-	memory-region = <&gfx_memory>;
-};
-
-&gpio0 {
-	gpio-line-names =
-
-	/*A0-A7*/
-	"","","","","","","","",
-
-	/*B0-B7*/
-	"BATTERY_DETECT", "", "", "BMC_READY",
-	"", "FM_ID_LED", "", "",
-
-	/*C0-C7*/
-	"","","","","","","","",
-
-	/*D0-D7*/
-	"","","","","","","","",
-
-	/*E0-E7*/
-	"","","","","","","","",
-
-	/*F0-F7*/
-	"","","","","","","","",
-
-	/*G0-G7*/
-	"FM_MUX1_SEL", "", "", "",
-	"", "", "FM_DEBUG_PORT_PRSNT_N", "FM_BMC_DBP_PRESENT_N",
-
-	/*H0-H7*/
-	"","","","","","","","",
-
-	/*I0-I7*/
-	"", "", "", "",
-	"", "FLASH_WP_STATUS", "BMC_JTAG_MUX_SEL", "",
-
-	/*J0-J7*/
-	"","","","","","","","",
-
-	/*K0-K7*/
-	"","","","","","","","",
-
-	/*L0-L7*/
-	"","","","","","","","",
-
-	/*M0-M7*/
-	"", "BMC_FRU_WP", "", "",
-	"", "", "", "",
-
-	/*N0-N7*/
-	"LED_POSTCODE_0", "LED_POSTCODE_1", "LED_POSTCODE_2", "LED_POSTCODE_3",
-	"LED_POSTCODE_4", "LED_POSTCODE_5", "LED_POSTCODE_6", "LED_POSTCODE_7",
-
-	/*O0-O7*/
-	"","","","","","","","",
-
-	/*P0-P7*/
-	"PWR_BTN_BMC_BUF_N", "", "ID_RST_BTN_BMC_N", "",
-	"PWR_LED", "", "", "BMC_HEARTBEAT_N",
-
-	/*Q0-Q7*/
-	"","","","","","","","",
-
-	/*R0-R7*/
-	"","","","","","","","",
-
-	/*S0-S7*/
-	"", "", "SYS_BMC_PWRBTN_N", "",
-	"", "", "", "RUN_POWER_FAULT",
-
-	/*T0-T7*/
-	"","","","","","","","",
-
-	/*U0-U7*/
-	"","","","","","","","",
-
-	/*V0-V7*/
-	"","","","","","","","",
-
-	/*W0-W7*/
-	"","","","","","","","",
-
-	/*X0-X7*/
-	"","","","","","","","",
-
-	/*Y0-Y7*/
-	"","","","","","","","",
-
-	/*Z0-Z7*/
-	"SPI_BMC_TPM_CS2_N", "", "", "SPI_BMC_TPM_CLK",
-	"SPI_BMC_TPM_MOSI", "SPI_BMC_TPM_MISO", "", "";
-};
-
-&gpio1 {
-	gpio-line-names =
-	/*18A0-18A7*/
-	"","","","","","","","",
-
-	/*18B0-18B7*/
-	"","","","",
-	"FM_BOARD_BMC_REV_ID0", "FM_BOARD_BMC_REV_ID1",
-	"FM_BOARD_BMC_REV_ID2", "",
-
-	/*18C0-18C7*/
-	"","","","","","","","",
-
-	/*18D0-18D7*/
-	"","","","","","","","",
-
-	/*18E0-18E3*/
-	"FM_BMC_PROT_LS_EN", "AC_PWR_BMC_BTN_N", "", "";
-};
-
-// L Bridge Board
-&i2c0 {
-	status = "okay";
-
-	eeprom@50 {
-		compatible = "atmel,24c2048";
-		reg = <0x50>;
-		pagesize = <128>;
-	};
-
-	i2c-mux@70 {
-		compatible = "nxp,pca9546";
-		reg = <0x70>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		i2c-mux-idle-disconnect;
-
-		i2c0mux0ch0: i2c@0 {
-			reg = <0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c0mux0ch1: i2c@1 {
-			reg = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c0mux0ch2: i2c@2 {
-			reg = <2>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c0mux0ch3: i2c@3 {
-			reg = <3>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-	};
-};
-
-// R Bridge Board
-&i2c1 {
-	status = "okay";
-
-	eeprom@50 {
-		compatible = "atmel,24c2048";
-		reg = <0x50>;
-		pagesize = <128>;
-	};
-
-	i2c-mux@70 {
-		compatible = "nxp,pca9546";
-		reg = <0x70>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		i2c-mux-idle-disconnect;
-
-		i2c1mux0ch0: i2c@0 {
-			reg = <0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c1mux0ch1: i2c@1 {
-			reg = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c1mux0ch2: i2c@2 {
-			reg = <2>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c1mux0ch3: i2c@3 {
-			reg = <3>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-	};
-};
-
-// MB - E1.S
-&i2c4 {
-	status = "okay";
-
-	i2c-mux@70 {
-		compatible = "nxp,pca9548";
-		reg = <0x70>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		i2c-mux-idle-disconnect;
-
-		i2c4mux0ch0: i2c@0 {
-			reg = <0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c4mux0ch1: i2c@1 {
-			reg = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c4mux0ch2: i2c@2 {
-			reg = <2>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c4mux0ch3: i2c@3 {
-			reg = <3>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c4mux0ch4: i2c@4 {
-			reg = <4>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c4mux0ch5: i2c@5 {
-			reg = <5>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c4mux0ch6: i2c@6 {
-			reg = <6>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c4mux0ch7: i2c@7 {
-			reg = <7>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-	};
-};
-
-// AMC
-&i2c5 {
-	status = "okay";
-};
-
-// MB
-&i2c6 {
-	status = "okay";
-
-	// HPM FRU
-	eeprom@50 {
-		compatible = "atmel,24c256";
-		reg = <0x50>;
-	};
-};
-
-// SCM
-&i2c7 {
-	status = "okay";
-
-
-};
-
-// MB - PDB
-&i2c8 {
-	status = "okay";
-
-	i2c-mux@72 {
-		compatible = "nxp,pca9546";
-		reg = <0x72>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		i2c-mux-idle-disconnect;
-
-		i2c8mux0ch0: i2c@0 {
-			reg = <0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			adc@1f {
-				compatible = "ti,adc128d818";
-				reg = <0x1f>;
-				ti,mode = /bits/ 8 <1>;
-			};
-
-			gpio@22 {
-				compatible = "nxp,pca9555";
-				reg = <0x22>;
-				gpio-controller;
-				#gpio-cells = <2>;
-
-				interrupt-parent = <&sgpiom0>;
-				interrupts = <174 IRQ_TYPE_LEVEL_LOW>;
-
-				gpio-line-names =
-					"RPDB_FAN_FULL_SPEED_R_N", "RPDB_I2C_TEMP75_U8_ALERT_R_N",
-					"RPDB_I2C_TMP432_U29_ALERT_R_N", "RPDB_GLOBAL_WP",
-					"RPDB_FAN_CT_FAN_FAIL_R_N", "",
-					"", "",
-					"RPDB_ALERT_P50V_HSC2_R_N", "RPDB_ALERT_P50V_HSC3_R_N",
-					"RPDB_ALERT_P50V_HSC4_R_N", "RPDB_ALERT_P50V_STBY_R_N",
-					"RPDB_I2C_P12V_MB_VRM_ALERT_R_N",
-					"RPDB_I2C_P12V_STBY_VRM_ALERT_R_N",
-					"RPDB_PGD_P3V3_STBY_PWRGD_R",
-					"RPDB_P12V_STBY_VRM_PWRGD_BUF_R";
-			};
-
-			gpio@24 {
-				compatible = "nxp,pca9555";
-				reg = <0x24>;
-				gpio-controller;
-				#gpio-cells = <2>;
-
-				interrupt-parent = <&sgpiom0>;
-				interrupts = <174 IRQ_TYPE_LEVEL_LOW>;
-
-				gpio-line-names =
-					"RPDB_EAM2_PRSNT_MOS_N_R", "RPDB_EAM3_PRSNT_MOS_N_R",
-					"RPDB_PWRGD_P50V_HSC4_SYS_R",
-					"RPDB_PWRGD_P50V_STBY_SYS_BUF_R",
-					"RPDB_P50V_FAN1_R2_PG", "RPDB_P50V_FAN2_R2_PG",
-					"RPDB_P50V_FAN3_R2_PG", "RPDB_P50V_FAN4_R2_PG",
-					"", "RPDB_FAN1_PRSNT_N_R",
-					"", "RPDB_FAN2_PRSNT_N_R",
-					"RPDB_FAN3_PRSNT_N_R", "RPDB_FAN4_PRSNT_N_R",
-					"", "";
-			};
-
-			// R-PDB FRU
-			eeprom@50 {
-				compatible = "atmel,24c128";
-				reg = <0x50>;
-			};
-		};
-		i2c8mux0ch1: i2c@1 {
-			reg = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			gpio@22 {
-				compatible = "nxp,pca9555";
-				reg = <0x22>;
-				gpio-controller;
-				#gpio-cells = <2>;
-
-				interrupt-parent = <&sgpiom0>;
-				interrupts = <174 IRQ_TYPE_LEVEL_LOW>;
-
-				gpio-line-names =
-					"LPDB_FAN_FULL_SPEED_R_N","LPDB_I2C_TEMP75_U8_ALERT_R_N",
-					"LPDB_I2C_TMP432_U29_ALERT_R_N","LPDB_GLOBAL_WP",
-					"LPDB_FAN_CT_FAN_FAIL_R_N","",
-					"","",
-					"LPDB_ALERT_P50V_HSC0_R_N","LPDB_ALERT_P50V_HSC1_R_N",
-					"LPDB_ALERT_P50V_HSC5_R_N","LPDB_I2C_P12V_SW_VRM_ALERT_R_N",
-					"LPDB_EAM0_PRSNT_MOS_N_R","LPDB_EAM1_PRSNT_MOS_N_R",
-					"LPDB_PWRGD_P50V_HSC5_SYS_R","";
-			};
-
-			gpio@24 {
-				compatible = "nxp,pca9555";
-				reg = <0x24>;
-				gpio-controller;
-				#gpio-cells = <2>;
-
-				interrupt-parent = <&sgpiom0>;
-				interrupts = <174 IRQ_TYPE_LEVEL_LOW>;
-
-				gpio-line-names =
-					"LPDB_P50V_FAN1_R2_PG","LPDB_P50V_FAN2_R2_PG",
-					"LPDB_P50V_FAN3_R2_PG","LPDB_P50V_FAN4_R2_PG",
-					"LPDB_P50V_FAN5_R2_PG","LPDB_FAN1_PRSNT_N_R",
-					"LPDB_FAN2_PRSNT_N_R","LPDB_FAN3_PRSNT_N_R",
-					"LPDB_FAN4_PRSNT_N_R","LPDB_FAN5_PRSNT_N_R",
-					"","",
-					"","",
-					"","";
-			};
-
-			// L-PDB FRU
-			eeprom@50 {
-				compatible = "atmel,24c128";
-				reg = <0x50>;
-			};
-		};
-		i2c8mux0ch2: i2c@2 {
-			reg = <2>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c8mux0ch3: i2c@3 {
-			reg = <3>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-	};
-};
-
-// SCM
-&i2c9 {
-	status = "okay";
-
-	// SCM FRU
-	eeprom@50 {
-		compatible = "atmel,24c128";
-		reg = <0x50>;
-	};
-
-	// BSM FRU
-	eeprom@56 {
-		compatible = "atmel,24c64";
-		reg = <0x56>;
-	};
-};
-
-// R Bridge Board
-&i2c10 {
-	status = "okay";
-
-	i2c-mux@71 {
-		compatible = "nxp,pca9548";
-		reg = <0x71>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		i2c-mux-idle-disconnect;
-
-		i2c10mux0ch0: i2c@0 {
-			reg = <0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c10mux0ch1: i2c@1 {
-			reg = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c10mux0ch2: i2c@2 {
-			reg = <2>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c10mux0ch3: i2c@3 {
-			reg = <3>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c10mux0ch4: i2c@4 {
-			reg = <4>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c10mux0ch5: i2c@5 {
-			reg = <5>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			gpio@22 {
-				compatible = "nxp,pca9555";
-				reg = <0x22>;
-				gpio-controller;
-				#gpio-cells = <2>;
-
-				gpio-line-names =
-					"","",
-					"","RBB_CPLD_REFRESH_IN_PRGRS_R_L",
-					"RBB_EAM0_NIC_CBL_PRSNT_R_L","RBB_EAM1_NIC_CBL_PRSNT_R_L",
-					"RBB_AINIC_JTAG_MUX_R2_SEL","RBB_SPI_MUX0_R2_SEL",
-					"RBB_AINIC_PRSNT_R_L","RBB_AINIC_OE_R_N",
-					"RBB_AINIC_BOARD_R2_ID","RBB_RST_USB2_HUB_R_N",
-					"RBB_RST_FT4222_R_N","RBB_RST_MCP2210_R_N",
-					"","";
-			};
-
-			// R Bridge Board FRU
-			eeprom@52 {
-				compatible = "atmel,24c256";
-				reg = <0x52>;
-			};
-		};
-		i2c10mux0ch6: i2c@6 {
-			reg = <6>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c10mux0ch7: i2c@7 {
-			reg = <7>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-	};
-};
-
-// L Bridge Board
-&i2c11 {
-	status = "okay";
-
-	i2c-mux@71 {
-		compatible = "nxp,pca9548";
-		reg = <0x71>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		i2c-mux-idle-disconnect;
-
-		i2c11mux0ch0: i2c@0 {
-			reg = <0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c11mux0ch1: i2c@1 {
-			reg = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c11mux0ch2: i2c@2 {
-			reg = <2>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c11mux0ch3: i2c@3 {
-			reg = <3>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c11mux0ch4: i2c@4 {
-			reg = <4>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c11mux0ch5: i2c@5 {
-			reg = <5>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			gpio@22 {
-				compatible = "nxp,pca9555";
-				reg = <0x22>;
-				gpio-controller;
-				#gpio-cells = <2>;
-
-				gpio-line-names =
-					"","",
-					"","LBB_CPLD_REFRESH_IN_PRGRS_R_L",
-					"LBB_EAM0_NIC_CBL_PRSNT_R_L","LBB_EAM1_NIC_CBL_PRSNT_R_L",
-					"LBB_AINIC_JTAG_MUX_R2_SEL","LBB_SPI_MUX0_R2_SEL",
-					"LBB_AINIC_PRSNT_R_L","LBB_AINIC_OE_R_N",
-					"LBB_AINIC_BOARD_R2_ID","LBB_RST_USB2_HUB_R_N",
-					"LBB_RST_FT4222_R_N","LBB_RST_MCP2210_R_N",
-					"","";
-			};
-
-			// L Bridge Board FRU
-			eeprom@52 {
-				compatible = "atmel,24c256";
-				reg = <0x52>;
-			};
-		};
-		i2c11mux0ch6: i2c@6 {
-			reg = <6>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c11mux0ch7: i2c@7 {
-			reg = <7>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-	};
-};
-
-// Debug Card
-&i2c12 {
-	status = "okay";
-};
-
-// MB
-&i2c13 {
-	status = "okay";
-
-	i2c-mux@70 {
-		compatible = "nxp,pca9548";
-		reg = <0x70>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		i2c-mux-idle-disconnect;
-
-		i2c13mux0ch0: i2c@0 {
-			reg = <0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c13mux0ch1: i2c@1 {
-			reg = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c13mux0ch2: i2c@2 {
-			reg = <2>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c13mux0ch3: i2c@3 {
-			reg = <3>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			adc@1f {
-				compatible = "ti,adc128d818";
-				reg = <0x1f>;
-				ti,mode = /bits/ 8 <1>;
-			};
-		};
-		i2c13mux0ch4: i2c@4 {
-			reg = <4>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			// HPM BRD ID FRU
-			eeprom@51 {
-				compatible = "atmel,24c256";
-				reg = <0x51>;
-			};
-		};
-		i2c13mux0ch5: i2c@5 {
-			reg = <5>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c13mux0ch6: i2c@6 {
-			reg = <6>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-		i2c13mux0ch7: i2c@7 {
-			reg = <7>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			nfc@28 {
-				compatible = "nxp,nxp-nci-i2c";
-				reg = <0x28>;
-
-				interrupt-parent = <&sgpiom0>;
-				interrupts = <156 IRQ_TYPE_LEVEL_HIGH>;
-
-				enable-gpios = <&sgpiom0 241 GPIO_ACTIVE_HIGH>;
-			};
-		};
-	};
-};
-
-// SCM
-&i2c14 {
-	status = "okay";
-};
-
-&i2c15 {
-	status = "okay";
-};
-
-&kcs2 {
-	aspeed,lpc-io-reg = <0xca8>;
-	status = "okay";
-};
-
-&kcs3 {
-	aspeed,lpc-io-reg = <0xca2>;
-	status = "okay";
-};
-
-&lpc_ctrl {
-	status = "okay";
-};
-
-&mac2 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ncsi3_default>;
-	use-ncsi;
-};
-
-&sgpiom0 {
-	ngpios = <128>;
-	bus-frequency = <2000000>;
-	gpio-line-names =
-	/*in - out - in - out */
-	/* A0-A7 line 0-15 */
-	"", "FM_CPU0_SYS_RESET_N", "", "CPU0_KBRST_N",
-	"", "FM_CPU0_PROCHOT_trigger_N", "", "FM_CLR_CMOS_R_P0",
-	"", "Force_I3C_SEL", "", "SYSTEM_Force_Run_AC_Cycle",
-	"", "", "", "",
-
-	/* B0-B7 line 16-31 */
-	"Channel0_leakage_EAM3", "FM_CPU_FPGA_JTAG_MUX_SEL",
-	"Channel1_leakage_EAM0", "FM_SCM_JTAG_MUX_SEL",
-	"Channel2_leakage_Manifold1", "FM_BRIDGE_JTAG_MUX_SEL",
-	"Channel3_leakage", "FM_CPU0_NMI_SYNC_FLOOD_N",
-	"Channel4_leakage_Manifold2", "",
-	"Channel5_leakage_EAM1", "",
-	"Channel6_leakage_CPU_DIMM", "",
-	"Channel7_leakage_EAM2", "",
-
-	/* C0-C7 line 32-47 */
-	"RSVD_RMC_GPIO3", "", "", "",
-	"", "", "", "",
-	"LEAK_DETECT_RMC_N", "JTAG_CPLD_TRST_R_N", "", "",
-	"", "", "", "",
-
-	/* D0-D7 line 48-63 */
-	"PWRGD_PDB_EAMHSC0_CPLD_PG_R", "",
-	"PWRGD_PDB_EAMHSC1_CPLD_PG_R", "",
-	"PWRGD_PDB_EAMHSC2_CPLD_PG_R", "",
-	"PWRGD_PDB_EAMHSC3_CPLD_PG_R", "",
-	"AMC_BRD_PRSNT_CPLD_L", "", "", "",
-	"", "", "", "",
-
-	/* E0-E7 line 64-79 */
-	"AMC_PDB_EAMHSC0_CPLD_EN_R", "",
-	"AMC_PDB_EAMHSC1_CPLD_EN_R", "",
-	"AMC_PDB_EAMHSC2_CPLD_EN_R", "",
-	"AMC_PDB_EAMHSC3_CPLD_EN_R", "",
-	"", "", "", "",
-	"", "", "", "",
-
-	/* F0-F7 line 80-95 */
-	"PWRGD_PVDDCR_CPU1_P0", "SGPIO_READY",
-	"PWRGD_PVDDCR_CPU0_P0", "",
-	"", "", "", "",
-	"", "", "", "",
-
-	/* G0-G7 line 96-111 */
-	"L_PRSNT_EDSFF0_N", "",
-	"L_PRSNT_EDSFF1_N", "",
-	"R_PRSNT_EDSFF2_N", "",
-	"R_PRSNT_EDSFF3_N", "",
-	"HPM_EDSFF_PG", "",
-	"PWRGD_CHEH_CPU0_FPGA", "",
-	"PWRGD_CHAD_CPU0_FPGA", "FM_BMC_READY_PLD",
-	"", "",
-
-	/* H0-H7 line 112-127 */
-	"PWRGD_P3V3", "",
-	"P12V_DDR_IP_PWRGD_R", "",
-	"P12V_DDR_AH_PWRGD_R", "",
-	"PWRGD_P12V_VRM1_CPLD_PG_R", "",
-	"PWRGD_P12V_VRM0_CPLD_PG_R", "",
-	"PWRGD_PDB_HSC4_CPLD_PG_R", "",
-	"PWRGD_PVDD18_S5_P0_PG", "",
-	"PWRGD_PVDD33_S5_P0_PG", "",
-
-	/* I0-I7 line 128-143 */
-	"EAM0_BRD_PRSNT_R_L", "",
-	"EAM1_BRD_PRSNT_R_L", "",
-	"EAM2_BRD_PRSNT_R_L", "",
-	"EAM3_BRD_PRSNT_R_L", "",
-	"EAM0_CPU_MOD_PWR_GD_R", "",
-	"EAM1_CPU_MOD_PWR_GD_R", "",
-	"PRSNT_EDSFF_BOOT_N", "",
-	"EAM3_CPU_MOD_PWR_GD_R", "",
-
-	/* J0-J7 line 144-159 */
-	"PRSNT_L_BIRDGE_R", "",
-	"PRSNT_R_BIRDGE_R", "",
-	"BRIDGE_L_MAIN_PG_R", "",
-	"BRIDGE_R_MAIN_PG_R", "",
-	"BRIDGE_L_STBY_PG_R", "",
-	"BRIDGE_R_STBY_PG_R", "",
-	"", "", "", "",
-
-	/* K0-K7 line 160-175 */
-	"ADC_I2C_ALERT_N", "",
-	"TEMP_I2C_ALERT_R_L", "",
-	"CPU0_VR_SMB_ALERT_CPLD_N", "",
-	"COVER_INTRUDER_R_N", "",
-	"HANDLE_INTRUDER_CPLD_N", "",
-	"IRQ_MCIO_CPLD_WAKE_R_N", "",
-	"APML_CPU0_ALERT_R_N", "",
-	"PDB_ALERT_R_N", "",
-
-	/* L0-L7 line 176-191 */
-	"L_EDSFF0_PG", "", "L_EDSFF1_PG", "",
-	"R_EDSFF2_PG", "", "R_EDSFF3_PG", "",
-	"CPU0_CORETYPE0", "", "CPU0_CORETYPE1", "",
-	"CPU0_CORETYPE2", "", "FM_BIOS_POST_CMPLT_R_N", "",
-
-	/* M0-M7 line 192-207 */
-	"EAM0_SMERR_CPLD_R_L", "",
-	"EAM1_SMERR_CPLD_R_L", "",
-	"EAM2_SMERR_CPLD_R_L", "",
-	"EAM3_SMERR_CPLD_R_L", "",
-	"CPU0_SMERR_N_R", "",
-	"CPU0_NV_SAVE_N_R", "",
-	"PDB_PWR_LOSS_CPLD_N", "",
-	"IRQ_BMC_SMI_ACTIVE_R_N", "",
-
-	/* N0-N7 line 208-223 */
-	"AMCROT_BMC_S5_RDY_R", "",
-	"AMC_RDY_R", "",
-	"AMC_STBY_PGOOD_R", "",
-	"CPU_AMC_SLP_S5_R_L", "",
-	"AMC_CPU_EAMPG_R", "",
-	"", "", "", "",
-
-	/* O0-O7 line 224-239 */
-	"HPM_PWR_FAIL", "Port80_b0",
-	"FM_DIMM_IP_FAIL", "Port80_b1",
-	"FM_DIMM_AH_FAIL", "Port80_b2",
-	"AMC_THERMTRIP_ASSERT", "Port80_b3",
-	"CPU_THERMTRIP_ASSERT", "Port80_b4",
-	"PVDDCR_SOC_P0_OCP_L", "Port80_b5",
-	"CPLD_SGPIO_RDY", "Port80_b6",
-	"", "Port80_b7",
-
-	/* P0-P7 line 240-255 */
-	"CPU0_SLP_S5_N_R", "NFC_VEN",
-	"CPU0_SLP_S3_N_R", "",
-	"FM_CPU0_PWRGD", "",
-	"PWRGD_RMC", "",
-	"FM_RST_CPU0_RESET_N", "",
-	"FM_PWRGD_CPU0_PWROK", "",
-	"wS5_PWR_Ready", "",
-	"wS0_ON_N", "PWRGD_P1V0_AUX";
-	status = "okay";
-};
-
-// BIOS Flash
-&spi2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_spi2_default>;
-	status = "okay";
-	reg = <0x1e631000 0xc4>, <0x50000000 0x8000000>;
-
-	flash@0 {
-		compatible = "jedec,spi-nor";
-		label = "pnor";
-		spi-max-frequency = <12000000>;
-		spi-tx-bus-width = <2>;
-		spi-rx-bus-width = <2>;
-		status = "okay";
-	};
-};
-
-// HOST BIOS Debug
-&uart1 {
-	status = "okay";
-};
-
-&uart3 {
-	status = "okay";
-};
-
-&uart4 {
-	status = "okay";
-};
-
-// BMC Debug Console
-&uart5 {
-	status = "okay";
-};
-
-&uart_routing {
-	status = "okay";
-};
-
-&uhci {
-	status = "okay";
-};
-
-&vhub {
-	status = "okay";
-	pinctrl-names = "default";
-};
-
-&video {
-	status = "okay";
-	memory-region = <&video_engine_memory>;
-};
-
-&wdt1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_wdtrst1_default>;
-	aspeed,reset-type = "soc";
-	aspeed,external-signal;
-	aspeed,ext-push-pull;
-	aspeed,ext-active-high;
-	aspeed,ext-pulse-duration = <256>;
-	status = "okay";
-};

-- 
2.34.1

[PATCH v3 3/9] ARM: dts: aspeed: anacapa: add EVT2 devicetree inheriting EVT1

[Colin Huang via B4 Relay]

From: Colin Huang <u8813345@gmail.com>

Add a development-phase devicetree for the Facebook Anacapa BMC EVT2
hardware revision and update the Anacapa wrapper DTS to reference
it.

Signed-off-by: Colin Huang <u8813345@gmail.com>
---
 .../aspeed/aspeed-bmc-facebook-anacapa-evt2.dts    | 178 +++++++++++++++++++++
 .../dts/aspeed/aspeed-bmc-facebook-anacapa.dts     |   2 +-
 2 files changed, 179 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt2.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt2.dts
new file mode 100644
index 000000000000..4a6ae7c6cbf8
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt2.dts
@@ -0,0 +1,178 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+/dts-v1/;
+#include "aspeed-bmc-facebook-anacapa-evt1.dts"
+
+/ {
+	model = "Facebook Anacapa BMC";
+	compatible = "facebook,anacapa-bmc-evt2", "aspeed,ast2600";
+};
+
+&sgpiom0 {
+	ngpios = <128>;
+	bus-frequency = <2000000>;
+	gpio-line-names =
+	/*in - out */
+	/* A0-A7 line 0-15 */
+	"L_FNIC_FLT", "FM_CPU0_SYS_RESET_N",
+	"L_BNIC0_FLT", "CPU0_KBRST_N",
+	"L_BNIC1_FLT", "FM_CPU0_PROCHOT_trigger_N",
+	"L_BNIC2_FLT", "FM_CLR_CMOS_R_P0",
+	"L_BNIC3_FLT", "Force_I3C_SEL",
+	"L_RTM_SW_FLT", "SYSTEM_Force_Run_AC_Cycle",
+	"", "",
+	"", "",
+
+	/* B0-B7 line 16-31 */
+	"Channel0_leakage_EAM3", "FM_CPU_FPGA_JTAG_MUX_SEL",
+	"Channel1_leakage_EAM0", "FM_SCM_JTAG_MUX_SEL",
+	"Channel2_leakage_Manifold1", "FM_BRIDGE_JTAG_MUX_SEL",
+	"Channel5_leakage_present_EAM1", "FM_CPU0_NMI_SYNC_FLOOD_N",
+	"Channel4_leakage_Manifold2", "BMC_AINIC0_WP_R2_L",
+	"Channel5_leakage_EAM1", "BMC_AINIC1_WP_R2_L",
+	"Channel6_leakage_CPU_DIMM", "CPLD_BUF_R_AGPIO330",
+	"Channel7_leakage_EAM2", "CPLD_BUF_R_AGPIO331",
+
+	/* C0-C7 line 32-47 */
+	"RSVD_RMC_GPIO3", "RTM_MUX_L",
+	"LEAK_DETECT_RMC_N", "RTM_MUX_R",
+	"HDR_P0_NMI_BTN_BUF_R_N", "FPGA_JTAG_SCM_DBREQ_N",
+	"Channel6_leakage_present_CPU_DIMM", "whdt_sel",
+	"", "JTAG_CPLD_TRST_R_N",
+	"", "",
+	"", "",
+	"", "",
+
+	/* D0-D7 line 48-63 */
+	"Channel0_leakage_present_EAM3", "",
+	"Channel1_leakage_present_EAM0", "",
+	"Channel2_leakage_present_Manifold1", "",
+	"Channel4_leakage_present_Manifold2", "",
+	"AMC_BRD_PRSNT_CPLD_L", "",
+	"Channel7_leakage_present_EAM2", "",
+	"", "",
+	"", "",
+
+	/* E0-E7 line 64-79 */
+	"L_PRSNT_B_FENIC_R2_N", "",
+	"L_PRSNT_B_BENIC0_R2_N", "",
+	"L_PRSNT_B_BENIC1_R2_N", "",
+	"L_PRSNT_B_BENIC2_R2_N", "",
+	"L_PRSNT_B_BENIC3_R2_N", "",
+	"", "",
+	"", "",
+	"", "",
+
+	/* F0-F7 line 80-95 */
+	"R_PRSNT_B_FENIC_R2_N", "SGPIO_READY",
+	"R_PRSNT_B_BENIC0_R2_N", "",
+	"R_PRSNT_B_BENIC1_R2_N", "",
+	"R_PRSNT_B_BENIC2_R2_N", "",
+	"R_PRSNT_B_BENIC3_R2_N", "",
+	"", "",
+	"", "",
+	"", "",
+
+	/* G0-G7 line 96-111 */
+	"L_PRSNT_EDSFF0_N", "",
+	"L_PRSNT_EDSFF1_N", "",
+	"R_PRSNT_EDSFF2_N", "",
+	"R_PRSNT_EDSFF3_N", "",
+	"HPM_EDSFF_PG", "",
+	"", "",
+	"", "FM_BMC_READY_PLD",
+	"PRSNT_NFC_BOARD_R", "",
+
+	/* H0-H7 line 112-127 */
+	"R_FNIC_FLT", "",
+	"R_BNIC0_FLT", "",
+	"R_BNIC1_FLT", "",
+	"R_BNIC2_FLT", "",
+	"R_BNIC3_FLT", "",
+	"R_RTM_SW_FLT", "",
+	"", "",
+	"", "",
+
+	/* I0-I7 line 128-143 */
+	"EAM0_BRD_PRSNT_R_L", "",
+	"EAM1_BRD_PRSNT_R_L", "",
+	"EAM2_BRD_PRSNT_R_L", "",
+	"EAM3_BRD_PRSNT_R_L", "",
+	"FM_TPM_PRSNT_R_N", "",
+	"PDB_L_PRSNT_R_N", "",
+	"PRSNT_EDSFF_BOOT_N", "",
+	"PRSNT_CPU0_N", "",
+
+	/* J0-J7 line 144-159 */
+	"PRSNT_L_BRIDGE_R", "",
+	"PRSNT_R_BRIDGE_R", "",
+	"BRIDGE_L_MAIN_PG_R", "",
+	"BRIDGE_R_MAIN_PG_R", "",
+	"BRIDGE_L_STBY_PG_R", "",
+	"BRIDGE_R_STBY_PG_R", "",
+	"IRQ_NFC_BOARD_R", "",
+	"RSMRST_N", "",
+
+	/* K0-K7 line 160-175 */
+	"ADC_I2C_ALERT_N", "",
+	"TEMP_I2C_ALERT_R_L", "",
+	"CPU0_VR_SMB_ALERT_CPLD_N", "",
+	"COVER_INTRUDER_R_N", "",
+	"HANDLE_INTRUDER_CPLD_N", "",
+	"IRQ_MCIO_CPLD_WAKE_R_N", "",
+	"APML_CPU0_ALERT_R_N", "",
+	"PDB_ALERT_R_N", "",
+
+	/* L0-L7 line 176-191 */
+	"L_EDSFF0_PG", "",
+	"L_EDSFF1_PG", "",
+	"R_EDSFF2_PG", "",
+	"R_EDSFF3_PG", "",
+	"HPM_CPLD_HEART_BIT", "",
+	"RBB_CPLD_HEART_BIT", "",
+	"LBB_CPLD_HEART_BIT", "",
+	"FM_BIOS_POST_CMPLT_R_N", "",
+
+	/* M0-M7 line 192-207 */
+	"EAM0_SMERR_CPLD_R_L", "",
+	"EAM1_SMERR_CPLD_R_L", "",
+	"EAM2_SMERR_CPLD_R_L", "",
+	"EAM3_SMERR_CPLD_R_L", "",
+	"CPU0_SMERR_N_R", "",
+	"CPU0_NV_SAVE_N_R", "",
+	"PDB_PWR_LOSS_CPLD_N", "",
+	"IRQ_BMC_SMI_ACTIVE_R_N", "",
+
+	/* N0-N7 line 208-223 */
+	"AMCROT_BMC_S5_RDY_R", "",
+	"AMC_RDY_R", "",
+	"AMC_STBY_PGOOD_R", "",
+	"CPU_AMC_SLP_S5_R_L", "",
+	"AMC_CPU_EAMPG_R", "",
+	"DIMM_PMIC_PG_TIMEOUT", "",
+	"EAM_MOD_PWR_GD_TIMEOUT", "",
+	"CPLD_AMC_STBY_PWR_EN", "",
+
+	/* O0-O7 line 224-239 */
+	"HPM_PWR_FAIL", "Port80_b0",
+	"FM_DIMM_IP_FAIL", "Port80_b1",
+	"FM_DIMM_AH_FAIL", "Port80_b2",
+	"AMC_THERMTRIP_ASSERT", "Port80_b3",
+	"CPU_THERMTRIP_ASSERT", "Port80_b4",
+	"PVDDCR_SOC_P0_OCP_L", "Port80_b5",
+	"CPLD_SGPIO_RDY", "Port80_b6",
+	"FM_MAIN_PWREN_RMC_EN_ISO", "Port80_b7",
+
+	/* P0-P7 line 240-255 */
+	"CPU0_SLP_S5_N_R", "NFC_VEN",
+	"CPU0_SLP_S3_N_R", "",
+	"FM_CPU0_PWRGD", "",
+	"PWRGD_RMC", "",
+	"FM_RST_CPU0_RESET_N", "RBB_CPLD_RISCV_RST",
+	"FM_PWRGD_CPU0_PWROK", "LBB_CPLD_RISCV_RST",
+	"AMC_FAIL", "HPM_CPLD_RISCV_RST",
+	"S0_ON", "";
+
+	status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa.dts
index 209eef65cedb..1848ca347621 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa.dts
@@ -1,4 +1,4 @@
 // SPDX-License-Identifier: GPL-2.0-or-later
 
-#include "aspeed-bmc-facebook-anacapa-evt1.dts"
+#include "aspeed-bmc-facebook-anacapa-evt2.dts"
 

-- 
2.34.1

[PATCH v3 4/9] ARM: dts: aspeed: anacapa: add DVT devicetree inheriting EVT2

[Colin Huang via B4 Relay]

From: Colin Huang <u8813345@gmail.com>

Add a development-phase devicetree for the Facebook Anacapa BMC DVT
hardware revision and update the Anacapa wrapper DTS to reference
it.

Signed-off-by: Colin Huang <u8813345@gmail.com>
---
 .../dts/aspeed/aspeed-bmc-facebook-anacapa-dvt.dts | 178 +++++++++++++++++++++
 .../dts/aspeed/aspeed-bmc-facebook-anacapa.dts     |   2 +-
 2 files changed, 179 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-dvt.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-dvt.dts
new file mode 100644
index 000000000000..0eb547ad0ec1
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-dvt.dts
@@ -0,0 +1,178 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+/dts-v1/;
+#include "aspeed-bmc-facebook-anacapa-evt2.dts"
+
+/ {
+	model = "Facebook Anacapa BMC";
+	compatible = "facebook,anacapa-bmc-dvt", "aspeed,ast2600";
+};
+
+&sgpiom0 {
+	ngpios = <128>;
+	bus-frequency = <2000000>;
+	gpio-line-names =
+	/*in - out */
+	/* A0-A7 line 0-15 */
+	"L_FNIC_FLT", "FM_CPU0_SYS_RESET_N",
+	"L_BNIC0_FLT", "CPU0_KBRST_N",
+	"L_BNIC1_FLT", "FM_CPU0_PROCHOT_trigger_N",
+	"L_BNIC2_FLT", "FM_CLR_CMOS_R_P0",
+	"L_BNIC3_FLT", "Force_I3C_SEL",
+	"L_RTM_SW_FLT", "SYSTEM_Force_Run_AC_Cycle",
+	"", "",
+	"", "",
+
+	/* B0-B7 line 16-31 */
+	"Channel0_leakage_EAM3", "FM_CPU_FPGA_JTAG_MUX_SEL",
+	"Channel1_leakage_EAM0", "FM_SCM_JTAG_MUX_SEL",
+	"Channel2_leakage_Manifold1", "FM_BRIDGE_JTAG_MUX_SEL",
+	"Channel5_leakage_present_EAM1", "FM_CPU0_NMI_SYNC_FLOOD_N",
+	"Channel4_leakage_Manifold2", "BMC_AINIC0_WP_R2_L",
+	"Channel5_leakage_EAM1", "BMC_AINIC1_WP_R2_L",
+	"Channel6_leakage_CPU_DIMM", "CPLD_BUF_R_AGPIO330",
+	"Channel7_leakage_EAM2", "CPLD_BUF_R_AGPIO331",
+
+	/* C0-C7 line 32-47 */
+	"RSVD_RMC_GPIO3", "RTM_MUX_L",
+	"LEAK_DETECT_RMC_N", "RTM_MUX_R",
+	"HDR_P0_NMI_BTN_BUF_R_N", "FPGA_JTAG_SCM_DBREQ_N",
+	"Channel6_leakage_present_CPU_DIMM", "whdt_sel",
+	"R_EAM0_NIC_CBL_PRSNT_L", "JTAG_CPLD_TRST_R_N",
+	"R_EAM1_NIC_CBL_PRSNT_L", "",
+	"L_EAM0_NIC_CBL_PRSNT_L", "",
+	"L_EAM1_NIC_CBL_PRSNT_L", "",
+
+	/* D0-D7 line 48-63 */
+	"Channel0_leakage_present_EAM3", "",
+	"Channel1_leakage_present_EAM0", "",
+	"Channel2_leakage_present_Manifold1", "",
+	"Channel4_leakage_present_Manifold2", "",
+	"AMC_BRD_PRSNT_CPLD_L", "",
+	"Channel7_leakage_present_EAM2", "",
+	"", "",
+	"", "",
+
+	/* E0-E7 line 64-79 */
+	"L_PRSNT_B_FENIC_R2_N", "",
+	"L_PRSNT_B_BENIC0_R2_N", "",
+	"L_PRSNT_B_BENIC1_R2_N", "",
+	"L_PRSNT_B_BENIC2_R2_N", "",
+	"L_PRSNT_B_BENIC3_R2_N", "",
+	"", "",
+	"", "",
+	"", "",
+
+	/* F0-F7 line 80-95 */
+	"R_PRSNT_B_FENIC_R2_N", "SGPIO_READY",
+	"R_PRSNT_B_BENIC0_R2_N", "",
+	"R_PRSNT_B_BENIC1_R2_N", "",
+	"R_PRSNT_B_BENIC2_R2_N", "",
+	"R_PRSNT_B_BENIC3_R2_N", "",
+	"", "",
+	"", "",
+	"", "",
+
+	/* G0-G7 line 96-111 */
+	"L_PRSNT_EDSFF0_N", "",
+	"L_PRSNT_EDSFF1_N", "",
+	"R_PRSNT_EDSFF2_N", "",
+	"R_PRSNT_EDSFF3_N", "",
+	"HPM_EDSFF_PG", "",
+	"", "",
+	"P12V_PWR_CABLE_PRSNT_L_R", "FM_BMC_READY_PLD",
+	"PRSNT_NFC_BOARD_R", "",
+
+	/* H0-H7 line 112-127 */
+	"R_FNIC_FLT", "",
+	"R_BNIC0_FLT", "",
+	"R_BNIC1_FLT", "",
+	"R_BNIC2_FLT", "",
+	"R_BNIC3_FLT", "",
+	"R_RTM_SW_FLT", "",
+	"RBB_Cable_Present", "",
+	"LBB_Cable_Present", "",
+
+	/* I0-I7 line 128-143 */
+	"EAM0_BRD_PRSNT_R_L", "",
+	"EAM1_BRD_PRSNT_R_L", "",
+	"EAM2_BRD_PRSNT_R_L", "",
+	"EAM3_BRD_PRSNT_R_L", "",
+	"FM_TPM_PRSNT_R_N", "",
+	"PDB_L_PRSNT_R_N", "",
+	"PRSNT_EDSFF_BOOT_N", "",
+	"PRSNT_CPU0_N", "",
+
+	/* J0-J7 line 144-159 */
+	"PRSNT_L_BRIDGE_R", "",
+	"PRSNT_R_BRIDGE_R", "",
+	"BRIDGE_L_MAIN_PG_R", "",
+	"BRIDGE_R_MAIN_PG_R", "",
+	"BRIDGE_L_STBY_PG_R", "",
+	"BRIDGE_R_STBY_PG_R", "",
+	"IRQ_NFC_BOARD_R", "",
+	"RSMRST_N", "",
+
+	/* K0-K7 line 160-175 */
+	"ADC_I2C_ALERT_N", "",
+	"TEMP_I2C_ALERT_R_L", "",
+	"CPU0_VR_SMB_ALERT_CPLD_N", "",
+	"COVER_INTRUDER_R_N", "",
+	"HANDLE_INTRUDER_CPLD_N", "",
+	"IRQ_MCIO_CPLD_WAKE_R_N", "",
+	"APML_CPU0_ALERT_R_N", "",
+	"PDB_ALERT_R_N", "",
+
+	/* L0-L7 line 176-191 */
+	"L_EDSFF0_PG", "",
+	"L_EDSFF1_PG", "",
+	"R_EDSFF2_PG", "",
+	"R_EDSFF3_PG", "",
+	"HPM_CPLD_HEART_BIT", "",
+	"RBB_CPLD_HEART_BIT", "",
+	"LBB_CPLD_HEART_BIT", "",
+	"FM_BIOS_POST_CMPLT_R_N", "",
+
+	/* M0-M7 line 192-207 */
+	"EAM0_SMERR_CPLD_R_L", "",
+	"EAM1_SMERR_CPLD_R_L", "",
+	"EAM2_SMERR_CPLD_R_L", "",
+	"EAM3_SMERR_CPLD_R_L", "",
+	"CPU0_SMERR_N_R", "",
+	"CPU0_NV_SAVE_N_R", "",
+	"PDB_PWR_LOSS_CPLD_N", "",
+	"IRQ_BMC_SMI_ACTIVE_R_N", "",
+
+	/* N0-N7 line 208-223 */
+	"AMCROT_BMC_S5_RDY_R", "",
+	"AMC_RDY_R", "",
+	"AMC_STBY_PGOOD_R", "",
+	"CPU_AMC_SLP_S5_R_L", "",
+	"AMC_CPU_EAMPG_R", "",
+	"DIMM_PMIC_PG_TIMEOUT", "",
+	"EAM_MOD_PWR_GD_TIMEOUT", "",
+	"CPLD_AMC_STBY_PWR_EN", "",
+
+	/* O0-O7 line 224-239 */
+	"HPM_PWR_FAIL", "Port80_b0",
+	"FM_DIMM_IP_FAIL", "Port80_b1",
+	"FM_DIMM_AH_FAIL", "Port80_b2",
+	"AMC_THERMTRIP_ASSERT", "Port80_b3",
+	"CPU_THERMTRIP_ASSERT", "Port80_b4",
+	"PVDDCR_SOC_P0_OCP_L", "Port80_b5",
+	"CPLD_SGPIO_RDY", "Port80_b6",
+	"FM_MAIN_PWREN_RMC_EN_ISO", "Port80_b7",
+
+	/* P0-P7 line 240-255 */
+	"CPU0_SLP_S5_N_R", "NFC_VEN",
+	"CPU0_SLP_S3_N_R", "",
+	"FM_CPU0_PWRGD", "",
+	"PWRGD_RMC", "",
+	"FM_RST_CPU0_RESET_N", "RBB_CPLD_RISCV_RST",
+	"FM_PWRGD_CPU0_PWROK", "LBB_CPLD_RISCV_RST",
+	"AMC_FAIL", "HPM_CPLD_RISCV_RST",
+	"S0_ON", "";
+
+	status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa.dts
index 1848ca347621..c74b211c42e6 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa.dts
@@ -1,4 +1,4 @@
 // SPDX-License-Identifier: GPL-2.0-or-later
 
-#include "aspeed-bmc-facebook-anacapa-evt2.dts"
+#include "aspeed-bmc-facebook-anacapa-dvt.dts"
 

-- 
2.34.1

[PATCH v3 5/9] ARM: dts: aspeed: anacapa: add additional EEPROM node for SCM

[Colin Huang via B4 Relay]

From: Colin Huang <u8813345@gmail.com>

The SCM FRU EEPROM I2C address differs between SCM revisions:
- Rev B uses address 0x50
- Rev C/D/E/F and later use address 0x51

Add an additional AT24C128 EEPROM node at 0x51 on i2c9 so the same
device tree can support multiple SCM revisions.

Signed-off-by: Colin Huang <u8813345@gmail.com>
---
 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts
index 9314ee493c61..1d2f46e83be8 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts
@@ -593,11 +593,20 @@ &i2c9 {
 	status = "okay";
 
 	// SCM FRU
+	// | DC-SCM Rev        | Slave address of eeprom  |
+	// |-------------------|--------------------------|
+	// | Rev B             | 0x50                     |
+	// | Rev C/D/E/F/above | 0x51                     |
 	eeprom@50 {
 		compatible = "atmel,24c128";
 		reg = <0x50>;
 	};
 
+	eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
 	// BSM FRU
 	eeprom@56 {
 		compatible = "atmel,24c64";

-- 
2.34.1

[PATCH v3 6/9] ARM: dts: aspeed: anacapa: Add eeprom device node for NFC adaptor board

[Colin Huang via B4 Relay]

From: Carl Lee <carl.lee@amd.com>

Add eeprom device node for NFC adaptor board FRU.

Signed-off-by: Carl Lee <carl.lee@amd.com>
---
 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts
index 1d2f46e83be8..c703d64edfae 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts
@@ -845,6 +845,11 @@ nfc@28 {
 
 				enable-gpios = <&sgpiom0 241 GPIO_ACTIVE_HIGH>;
 			};
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
 		};
 	};
 };

-- 
2.34.1

[PATCH v3 7/9] ARM: dts: aspeed: anacapa: Align PDB fan GPIO numbering

[Colin Huang via B4 Relay]

From: Rex Fu <rex.fu.amd@gmail.com>

Update the LPDB and RPDB fan GPIO line names to align with the platform
fan numbering scheme.

The LPDB fan GPIOs are named FAN0 through FAN4, while the RPDB fan GPIOs
are named FAN5 through FAN8. This keeps the GPIO line names consistent
with the fan inventory and platform-level fan numbering.

Signed-off-by: Rex Fu <rex.fu.amd@gmail.com>
---
 .../dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts  | 20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts
index c703d64edfae..29df10697613 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts
@@ -510,11 +510,11 @@ gpio@24 {
 					"RPDB_EAM2_PRSNT_MOS_N_R", "RPDB_EAM3_PRSNT_MOS_N_R",
 					"RPDB_PWRGD_P50V_HSC4_SYS_R",
 					"RPDB_PWRGD_P50V_STBY_SYS_BUF_R",
-					"RPDB_P50V_FAN1_R2_PG", "RPDB_P50V_FAN2_R2_PG",
-					"RPDB_P50V_FAN3_R2_PG", "RPDB_P50V_FAN4_R2_PG",
-					"", "RPDB_FAN1_PRSNT_N_R",
-					"", "RPDB_FAN2_PRSNT_N_R",
-					"RPDB_FAN3_PRSNT_N_R", "RPDB_FAN4_PRSNT_N_R",
+					"RPDB_P50V_FAN5_R2_PG", "RPDB_P50V_FAN6_R2_PG",
+					"RPDB_P50V_FAN7_R2_PG", "RPDB_P50V_FAN8_R2_PG",
+					"", "RPDB_FAN5_PRSNT_N_R",
+					"", "RPDB_FAN6_PRSNT_N_R",
+					"RPDB_FAN7_PRSNT_N_R", "RPDB_FAN8_PRSNT_N_R",
 					"", "";
 			};
 
@@ -559,11 +559,11 @@ gpio@24 {
 				interrupts = <174 IRQ_TYPE_LEVEL_LOW>;
 
 				gpio-line-names =
-					"LPDB_P50V_FAN1_R2_PG","LPDB_P50V_FAN2_R2_PG",
-					"LPDB_P50V_FAN3_R2_PG","LPDB_P50V_FAN4_R2_PG",
-					"LPDB_P50V_FAN5_R2_PG","LPDB_FAN1_PRSNT_N_R",
-					"LPDB_FAN2_PRSNT_N_R","LPDB_FAN3_PRSNT_N_R",
-					"LPDB_FAN4_PRSNT_N_R","LPDB_FAN5_PRSNT_N_R",
+					"LPDB_P50V_FAN0_R2_PG","LPDB_P50V_FAN1_R2_PG",
+					"LPDB_P50V_FAN2_R2_PG","LPDB_P50V_FAN3_R2_PG",
+					"LPDB_P50V_FAN4_R2_PG","LPDB_FAN0_PRSNT_N_R",
+					"LPDB_FAN1_PRSNT_N_R","LPDB_FAN2_PRSNT_N_R",
+					"LPDB_FAN3_PRSNT_N_R","LPDB_FAN4_PRSNT_N_R",
 					"","",
 					"","",
 					"","";

-- 
2.34.1

[PATCH v3 8/9] ARM: dts: aspeed: anacapa: Enable MCTP and FRU for NIC

[Colin Huang via B4 Relay]

From: Andy Chung <Andy.Chung@amd.com>

Add the mctp-controller property to enable frontend NIC management
via PLDM over MCTP.
Also add EEPROM device for NIC FRU and reorder the I2C virtual bus
index accroding to the system silkscreen index.

Signed-off-by: Andy Chung <Andy.Chung@amd.com>
---
 .../aspeed/aspeed-bmc-facebook-anacapa-evt1.dts    | 98 ++++++++++++++++++----
 1 file changed, 80 insertions(+), 18 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts
index 29df10697613..5b6ce3c556fe 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts
@@ -35,22 +35,22 @@ aliases {
 		i2c33 = &i2c8mux0ch1;
 		i2c34 = &i2c8mux0ch2;
 		i2c35 = &i2c8mux0ch3;
-		i2c36 = &i2c10mux0ch0;
-		i2c37 = &i2c10mux0ch1;
-		i2c38 = &i2c10mux0ch2;
-		i2c39 = &i2c10mux0ch3;
-		i2c40 = &i2c10mux0ch4;
-		i2c41 = &i2c10mux0ch5;
-		i2c42 = &i2c10mux0ch6;
-		i2c43 = &i2c10mux0ch7;
-		i2c44 = &i2c11mux0ch0;
-		i2c45 = &i2c11mux0ch1;
-		i2c46 = &i2c11mux0ch2;
-		i2c47 = &i2c11mux0ch3;
-		i2c48 = &i2c11mux0ch4;
-		i2c49 = &i2c11mux0ch5;
-		i2c50 = &i2c11mux0ch6;
-		i2c51 = &i2c11mux0ch7;
+		i2c36 = &i2c11mux0ch5;
+		i2c37 = &i2c11mux0ch6;
+		i2c38 = &i2c11mux0ch7;
+		i2c39 = &i2c11mux0ch0;
+		i2c40 = &i2c11mux0ch1;
+		i2c41 = &i2c11mux0ch2;
+		i2c42 = &i2c11mux0ch3;
+		i2c43 = &i2c11mux0ch4;
+		i2c44 = &i2c10mux0ch1;
+		i2c45 = &i2c10mux0ch2;
+		i2c46 = &i2c10mux0ch3;
+		i2c47 = &i2c10mux0ch4;
+		i2c48 = &i2c10mux0ch5;
+		i2c49 = &i2c10mux0ch6;
+		i2c50 = &i2c10mux0ch7;
+		i2c51 = &i2c10mux0ch0;
 		i2c52 = &i2c13mux0ch0;
 		i2c53 = &i2c13mux0ch1;
 		i2c54 = &i2c13mux0ch2;
@@ -617,13 +617,17 @@ eeprom@56 {
 // R Bridge Board
 &i2c10 {
 	status = "okay";
+	multi-master;
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
 
 	i2c-mux@71 {
 		compatible = "nxp,pca9548";
 		reg = <0x71>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		i2c-mux-idle-disconnect;
 
 		i2c10mux0ch0: i2c@0 {
 			reg = <0>;
@@ -634,21 +638,45 @@ i2c10mux0ch1: i2c@1 {
 			reg = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			mctp-controller;
+			// BE NIC FRU
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
 		};
 		i2c10mux0ch2: i2c@2 {
 			reg = <2>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			mctp-controller;
+			// BE NIC FRU
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
 		};
 		i2c10mux0ch3: i2c@3 {
 			reg = <3>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			mctp-controller;
+			// BE NIC FRU
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
 		};
 		i2c10mux0ch4: i2c@4 {
 			reg = <4>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			mctp-controller;
+			// BE NIC FRU
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
 		};
 		i2c10mux0ch5: i2c@5 {
 			reg = <5>;
@@ -694,38 +722,72 @@ i2c10mux0ch7: i2c@7 {
 // L Bridge Board
 &i2c11 {
 	status = "okay";
+	multi-master;
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
 
 	i2c-mux@71 {
 		compatible = "nxp,pca9548";
 		reg = <0x71>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		i2c-mux-idle-disconnect;
 
 		i2c11mux0ch0: i2c@0 {
 			reg = <0>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			mctp-controller;
+			// FE NIC FRU
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
 		};
 		i2c11mux0ch1: i2c@1 {
 			reg = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			mctp-controller;
+			// BE NIC FRU
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
 		};
 		i2c11mux0ch2: i2c@2 {
 			reg = <2>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			mctp-controller;
+			// BE NIC FRU
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
 		};
 		i2c11mux0ch3: i2c@3 {
 			reg = <3>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			mctp-controller;
+			// BE NIC FRU
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
 		};
 		i2c11mux0ch4: i2c@4 {
 			reg = <4>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			mctp-controller;
+			// BE NIC FRU
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
 		};
 		i2c11mux0ch5: i2c@5 {
 			reg = <5>;

-- 
2.34.1

[PATCH v3 9/9] ARM: dts: aspeed: anacapa: evt2: add shunt resistor values for HSC monitors

[Colin Huang via B4 Relay]

From: Peter Shen <peter.shen@amd.com>

Add shunt resistor configuration for LTC4287 hot-swap controllers on
Anacapa EVT2 platform.

The resistor values are required for accurate current and power
measurement by the driver. These settings reflect the actual BOM used
on EVT2, where different sense resistor values (150 uOhm and 250 uOhm)
are populated across rails.

Without this configuration, the reported readings would be incorrect.

Signed-off-by: Peter Shen <peter.shen@amd.com>
---
 .../aspeed/aspeed-bmc-facebook-anacapa-evt2.dts    | 50 ++++++++++++++++++++++
 1 file changed, 50 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt2.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt2.dts
index 4a6ae7c6cbf8..59875e9d84fd 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt2.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt2.dts
@@ -8,6 +8,56 @@ / {
 	compatible = "facebook,anacapa-bmc-evt2", "aspeed,ast2600";
 };
 
+// MB - PDB
+&i2c8 {
+
+	i2c-mux@72 {
+
+		i2c8mux0ch0: i2c@0 {
+
+			power-monitor@42 {
+				compatible = "lltc,ltc4287";
+				reg = <0x42>;
+				shunt-resistor-micro-ohms = <150>;
+			};
+			power-monitor@43 {
+				compatible = "lltc,ltc4287";
+				reg = <0x43>;
+				shunt-resistor-micro-ohms = <150>;
+			};
+			power-monitor@44 {
+				compatible = "lltc,ltc4287";
+				reg = <0x44>;
+				shunt-resistor-micro-ohms = <250>;
+			};
+			power-monitor@45 {
+				compatible = "lltc,ltc4287";
+				reg = <0x45>;
+				shunt-resistor-micro-ohms = <250>;
+			};
+		};
+
+		i2c8mux0ch1: i2c@1 {
+
+			power-monitor@40 {
+				compatible = "lltc,ltc4287";
+				reg = <0x40>;
+				shunt-resistor-micro-ohms = <150>;
+			};
+			power-monitor@41 {
+				compatible = "lltc,ltc4287";
+				reg = <0x41>;
+				shunt-resistor-micro-ohms = <150>;
+			};
+			power-monitor@45 {
+				compatible = "lltc,ltc4287";
+				reg = <0x45>;
+				shunt-resistor-micro-ohms = <250>;
+			};
+		};
+	};
+};
+
 &sgpiom0 {
 	ngpios = <128>;
 	bus-frequency = <2000000>;

-- 
2.34.1

Re: [PATCH v3 2/9] ARM: dts: aspeed: anacapa: add EVT1 devicetree and point wrapper to it

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 2 potential issue(s) to consider:
- [Critical] Removal of the generic 'facebook,anacapa-bmc' compatible string from the root node breaks backward compatibility.
- [Low] Including a `.dts` file directly from another `.dts` file instead of using a `.dtsi`, and failing to register the new `.dts` in the Makefile.
--

commit 07c91fec99a871ad9f2589f35f8c19205df00ae9
Author: Colin Huang <u8813345@gmail.com>

ARM: dts: aspeed: anacapa: add EVT1 devicetree and point wrapper to it

This change introduces a development-phase devicetree for the Facebook Anacapa
BMC EVT1 hardware revision and updates the Anacapa wrapper DTS to reference it.

> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts
> new file mode 100644
> index 0000000000000..9314ee493c617
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts
> @@ -0,0 +1,1103 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +
> +/dts-v1/;

[Severity: Low]
Is this intended to be compiled independently as a top-level board?

Files that are included by other device trees usually use the .dtsi extension
and omit the /dts-v1/; tag. This file is also not added to the Makefile.

> +#include "aspeed-g6.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +#include <dt-bindings/i2c/i2c.h>
> +
> +/ {
> +	model = "Facebook Anacapa BMC";
> +	compatible = "facebook,anacapa-bmc-evt1", "aspeed,ast2600";

[Severity: Critical]
Does the removal of the generic "facebook,anacapa-bmc" compatible string
break backward compatibility with existing bootloaders or management tools?

Replacing the wrapper file with an include to this one completely removes the
original compatible string from the output DTB. 

Could this include a fallback like the following?
compatible = "facebook,anacapa-bmc-evt1", "facebook,anacapa-bmc", "aspeed,ast2600";

[ ... ]

> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa.dts
> index 1fddf3a5d1383..209eef65cedbc 100644
> --- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa.dts
> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa.dts
> @@ -1,1079 +1,4 @@
>  // SPDX-License-Identifier: GPL-2.0-or-later
>  
> -/dts-v1/;
> -#include "aspeed-g6.dtsi"
> -#include <dt-bindings/gpio/aspeed-gpio.h>
> -#include <dt-bindings/i2c/i2c.h>
> +#include "aspeed-bmc-facebook-anacapa-evt1.dts"

[Severity: Low]
Is there a reason to include a .dts file directly instead of using a .dtsi?

Using a .dts as an include bypasses standalone syntax checks and compilation.

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260602-anacapa-devlop-phase-devicetree-v3-0-7c93c5df8d9b@gmail.com?part=2

Re: [PATCH v3 8/9] ARM: dts: aspeed: anacapa: Enable MCTP and FRU for NIC

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 2 potential issue(s) to consider:
- [Medium] Incomplete implementation: missing MCTP and FRU enablement for the Right Frontend NIC.
- [Medium] Undocumented removal of the `i2c-mux-idle-disconnect` property.
--

commit e274c5d6bfd9557e3fa26fe21930d08b6e1b3ec0
Author: Andy Chung <Andy.Chung@amd.com>

ARM: dts: aspeed: anacapa: Enable MCTP and FRU for NIC

Add the mctp-controller property to enable frontend NIC management
via PLDM over MCTP. Also add EEPROM device for NIC FRU and reorder
the I2C virtual bus index accroding to the system silkscreen index.

> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts
> index 29df10697613a..5b6ce3c556fe2 100644
> --- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts
> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-anacapa-evt1.dts

[ ... ]

>  // R Bridge Board
>  &i2c10 {
>  	status = "okay";
> +	multi-master;
> +	mctp@10 {
> +		compatible = "mctp-i2c-controller";
> +		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
> +	};
>  
>  	i2c-mux@71 {
>  		compatible = "nxp,pca9548";
>  		reg = <0x71>;
>  		#address-cells = <1>;
>  		#size-cells = <0>;
> -		i2c-mux-idle-disconnect;

[Severity: Medium]
The commit message doesn't mention removing the i2c-mux-idle-disconnect
property.

While this is likely needed to allow asynchronous multi-master MCTP traffic
from endpoints, could the commit message document this topology change so
future maintainers don't inadvertently revert it?

>  
>  		i2c10mux0ch0: i2c@0 {
>  			reg = <0>;
>  			#address-cells = <1>;
>  			#size-cells = <0>;
>  		};

[Severity: Medium]
The commit message mentions enabling MCTP and FRU for frontend NICs, and the
symmetrically equivalent left frontend NIC (i2c11mux0ch0) was updated, but
this right frontend NIC node was left unmodified.

Did we miss adding the mctp-controller property and FRU eeprom for this
channel?

[ ... ]

>  // L Bridge Board
>  &i2c11 {
>  	status = "okay";
> +	multi-master;
> +	mctp@10 {
> +		compatible = "mctp-i2c-controller";
> +		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
> +	};
>  
>  	i2c-mux@71 {
>  		compatible = "nxp,pca9548";
>  		reg = <0x71>;
>  		#address-cells = <1>;
>  		#size-cells = <0>;
> -		i2c-mux-idle-disconnect;

[Severity: Medium]
Similarly here on the left bridge board, could we mention the removal of
the i2c-mux-idle-disconnect property in the commit message?

[ ... ]

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260602-anacapa-devlop-phase-devicetree-v3-0-7c93c5df8d9b@gmail.com?part=8

Re: [PATCH v3 1/9] dt-bindings: arm: aspeed: add Anacapa EVT1 EVT2 DVT board

[Conor Dooley]

[-- Attachment #1: Type: text/plain, Size: 75 bytes --]

Acked-by: Conor Dooley <conor.dooley@microchip.com>
pw-bot: not-applicable

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]