Devicetree
 help / color / mirror / Atom feed
From: Santhosh Kumar K <s-k6@ti.com>
To: <broonie@kernel.org>, <robh@kernel.org>, <krzk+dt@kernel.org>,
	<conor+dt@kernel.org>, <miquel.raynal@bootlin.com>,
	<richard@nod.at>, <vigneshr@ti.com>, <pratyush@kernel.org>,
	<mwalle@kernel.org>, <takahiro.kuwano@infineon.com>
Cc: <linux-spi@vger.kernel.org>, <devicetree@vger.kernel.org>,
	<linux-kernel@vger.kernel.org>, <linux-mtd@lists.infradead.org>,
	<praneeth@ti.com>, <u-kumar1@ti.com>, <a-dutta@ti.com>,
	<s-k6@ti.com>
Subject: [PATCH v4 06/16] spi: cadence-quadspi: move cqspi_readdata_capture earlier
Date: Thu, 18 Jun 2026 13:07:15 +0530	[thread overview]
Message-ID: <20260618073725.84733-7-s-k6@ti.com> (raw)
In-Reply-To: <20260618073725.84733-1-s-k6@ti.com>

Move cqspi_readdata_capture() function earlier in the file. This is
preparatory refactoring for upcoming PHY tuning support for read and
write operations.

No functional changes.

Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
---
 drivers/spi/spi-cadence-quadspi.c | 45 +++++++++++++++----------------
 1 file changed, 22 insertions(+), 23 deletions(-)

diff --git a/drivers/spi/spi-cadence-quadspi.c b/drivers/spi/spi-cadence-quadspi.c
index aaba1a3ad577..54fd7b591e06 100644
--- a/drivers/spi/spi-cadence-quadspi.c
+++ b/drivers/spi/spi-cadence-quadspi.c
@@ -453,6 +453,28 @@ static int cqspi_wait_idle(struct cqspi_st *cqspi)
 	}
 }
 
+static void cqspi_readdata_capture(struct cqspi_st *cqspi, const bool bypass,
+				   const unsigned int delay)
+{
+	void __iomem *reg_base = cqspi->iobase;
+	unsigned int reg;
+
+	reg = readl(reg_base + CQSPI_REG_READCAPTURE);
+
+	if (bypass)
+		reg |= BIT(CQSPI_REG_READCAPTURE_BYPASS_LSB);
+	else
+		reg &= ~BIT(CQSPI_REG_READCAPTURE_BYPASS_LSB);
+
+	reg &= ~(CQSPI_REG_READCAPTURE_DELAY_MASK
+		 << CQSPI_REG_READCAPTURE_DELAY_LSB);
+
+	reg |= (delay & CQSPI_REG_READCAPTURE_DELAY_MASK)
+	       << CQSPI_REG_READCAPTURE_DELAY_LSB;
+
+	writel(reg, reg_base + CQSPI_REG_READCAPTURE);
+}
+
 static int cqspi_exec_flash_cmd(struct cqspi_st *cqspi, unsigned int reg)
 {
 	void __iomem *reg_base = cqspi->iobase;
@@ -1270,29 +1292,6 @@ static void cqspi_config_baudrate_div(struct cqspi_st *cqspi)
 	writel(reg, reg_base + CQSPI_REG_CONFIG);
 }
 
-static void cqspi_readdata_capture(struct cqspi_st *cqspi,
-				   const bool bypass,
-				   const unsigned int delay)
-{
-	void __iomem *reg_base = cqspi->iobase;
-	unsigned int reg;
-
-	reg = readl(reg_base + CQSPI_REG_READCAPTURE);
-
-	if (bypass)
-		reg |= BIT(CQSPI_REG_READCAPTURE_BYPASS_LSB);
-	else
-		reg &= ~BIT(CQSPI_REG_READCAPTURE_BYPASS_LSB);
-
-	reg &= ~(CQSPI_REG_READCAPTURE_DELAY_MASK
-		 << CQSPI_REG_READCAPTURE_DELAY_LSB);
-
-	reg |= (delay & CQSPI_REG_READCAPTURE_DELAY_MASK)
-		<< CQSPI_REG_READCAPTURE_DELAY_LSB;
-
-	writel(reg, reg_base + CQSPI_REG_READCAPTURE);
-}
-
 static void cqspi_configure(struct cqspi_flash_pdata *f_pdata,
 			    unsigned long sclk)
 {
-- 
2.34.1


  parent reply	other threads:[~2026-06-18  7:39 UTC|newest]

Thread overview: 29+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-06-18  7:37 [PATCH v4 00/16] spi: cadence-quadspi: add PHY tuning support Santhosh Kumar K
2026-06-18  7:37 ` [PATCH v4 01/16] spi: dt-bindings: add spi-max-post-config-frequency property Santhosh Kumar K
2026-06-18  7:37 ` [PATCH v4 02/16] spi: dt-bindings: add spi-phy-pattern-partition property Santhosh Kumar K
2026-06-18  7:50   ` sashiko-bot
2026-06-18  7:37 ` [PATCH v4 03/16] spi: parse spi-max-post-config-frequency into post_config_max_speed_hz Santhosh Kumar K
2026-06-18  7:54   ` sashiko-bot
2026-06-18  7:37 ` [PATCH v4 04/16] spi: spi-mem: teach spi_mem_adjust_op_freq() about post-config ops Santhosh Kumar K
2026-06-18  8:02   ` sashiko-bot
2026-06-18  7:37 ` [PATCH v4 05/16] spi: spi-mem: add execute_tuning callback and spi_mem_execute_tuning() Santhosh Kumar K
2026-06-18  7:57   ` sashiko-bot
2026-06-18  7:37 ` Santhosh Kumar K [this message]
2026-06-18  7:48   ` [PATCH v4 06/16] spi: cadence-quadspi: move cqspi_readdata_capture earlier sashiko-bot
2026-06-18  7:37 ` [PATCH v4 07/16] spi: cadence-quadspi: add DQS support to read data capture Santhosh Kumar K
2026-06-18  7:37 ` [PATCH v4 08/16] spi: cadence-quadspi: add PHY tuning support Santhosh Kumar K
2026-06-18  7:59   ` sashiko-bot
2026-06-18  7:37 ` [PATCH v4 09/16] spi: cadence-quadspi: skip DDR PHY tuning for 2-byte-address ops (i2383) Santhosh Kumar K
2026-06-18  8:04   ` sashiko-bot
2026-06-18  7:37 ` [PATCH v4 10/16] spi: cadence-quadspi: refactor direct read path for PHY support Santhosh Kumar K
2026-06-18  7:57   ` sashiko-bot
2026-06-18  7:37 ` [PATCH v4 11/16] spi: cadence-quadspi: enable PHY for direct reads Santhosh Kumar K
2026-06-18  7:53   ` sashiko-bot
2026-06-18  7:37 ` [PATCH v4 12/16] spi: cadence-quadspi: enable PHY for indirect writes Santhosh Kumar K
2026-06-18  7:53   ` sashiko-bot
2026-06-18  7:37 ` [PATCH v4 13/16] mtd: spinand: extract variant ranking logic into spinand_op_find_best() Santhosh Kumar K
2026-06-18  7:37 ` [PATCH v4 14/16] mtd: spinand: negotiate optimal PHY operating point before dirmap creation Santhosh Kumar K
2026-06-18  8:02   ` sashiko-bot
2026-06-18  7:37 ` [PATCH v4 15/16] mtd: spi-nor: extract read op template construction into helper Santhosh Kumar K
2026-06-18  7:37 ` [PATCH v4 16/16] mtd: spi-nor: run PHY tuning after init and update dirmap frequency Santhosh Kumar K
2026-06-18  8:01   ` sashiko-bot

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20260618073725.84733-7-s-k6@ti.com \
    --to=s-k6@ti.com \
    --cc=a-dutta@ti.com \
    --cc=broonie@kernel.org \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=krzk+dt@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mtd@lists.infradead.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=miquel.raynal@bootlin.com \
    --cc=mwalle@kernel.org \
    --cc=praneeth@ti.com \
    --cc=pratyush@kernel.org \
    --cc=richard@nod.at \
    --cc=robh@kernel.org \
    --cc=takahiro.kuwano@infineon.com \
    --cc=u-kumar1@ti.com \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox