[PATCH v4 08/16] spi: cadence-quadspi: add PHY tuning support

[Santhosh Kumar K <s-k6@ti.com>]

The Cadence QSPI controller supports a delay-line PHY for high-speed
operation. Without calibration the PHY is unused and read capture relies
on a fixed delay, limiting throughput at frequencies above the base
operating speed.

Add an execute_tuning callback that performs delay-line calibration using
a known data pattern written to a dedicated flash region. The pattern is
either read from a NOR partition identified by the DT property
spi-phy-pattern-partition, or written to the NAND page cache before
each calibration read.

For DDR protocols (8D-8D-8D) a 2D sweep of (rx_delay, tx_delay) pairs
is performed to find the widest passing region in the combined RX/TX
space. Binary search locates the gap boundary between passing regions
when two separate windows exist; the final operating point is placed at
the centre of the larger region with a small temperature-dependent
offset.

For SDR protocols a 1D sweep of the RX delay is sufficient. Two windows
at adjacent read_delay values are measured; the wider one's midpoint is
selected.

The tuning infrastructure is platform-specific: only am654-based OSPI
controllers populate the execute_tuning hook. All other platform data
entries return -EOPNOTSUPP and are unaffected.

The calibration target is sourced from spi->post_config_max_speed_hz,
populated by the SPI core from the spi-max-post-config-frequency DT
property. Tuning is skipped when post_config_max_speed_hz is zero.

Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
---
 drivers/spi/spi-cadence-quadspi.c | 1776 ++++++++++++++++++++++++++++-
 1 file changed, 1763 insertions(+), 13 deletions(-)

diff --git a/drivers/spi/spi-cadence-quadspi.c b/drivers/spi/spi-cadence-quadspi.c
index 201d69c64c49..72768292a32b 100644
--- a/drivers/spi/spi-cadence-quadspi.c
+++ b/drivers/spi/spi-cadence-quadspi.c
@@ -65,15 +65,25 @@ enum {
 
 struct cqspi_st;
 
+struct phy_setting {
+	u8			rx;
+	u8			tx;
+	u8			read_delay;
+};
+
 struct cqspi_flash_pdata {
-	struct cqspi_st	*cqspi;
-	u32		clk_rate;
-	u32		read_delay;
-	u32		tshsl_ns;
-	u32		tsd2d_ns;
-	u32		tchsh_ns;
-	u32		tslch_ns;
-	u8		cs;
+	struct cqspi_st		*cqspi;
+	u32			read_delay;
+	u32			tshsl_ns;
+	u32			tsd2d_ns;
+	u32			tchsh_ns;
+	u32			tslch_ns;
+	bool			use_dqs;
+	bool			use_tuned_phy;
+	u8			cs;
+	struct phy_setting	phy_setting;
+	struct spi_mem_op	phy_read_op;
+	struct spi_mem_op	phy_write_op;
 };
 
 static const struct clk_bulk_data cqspi_clks[CLK_QSPI_NUM] = {
@@ -129,12 +139,15 @@ struct cqspi_driver_platdata {
 	int (*indirect_read_dma)(struct cqspi_flash_pdata *f_pdata,
 				 u_char *rxbuf, loff_t from_addr, size_t n_rx);
 	u32 (*get_dma_status)(struct cqspi_st *cqspi);
+	int (*execute_tuning)(struct spi_mem *mem, struct spi_mem_op *read_op,
+			      struct spi_mem_op *write_op);
 };
 
 /* Operation timeout value */
 #define CQSPI_TIMEOUT_MS			500
 #define CQSPI_READ_TIMEOUT_MS			10
 #define CQSPI_BUSYWAIT_TIMEOUT_US		500
+#define CQSPI_DLL_TIMEOUT_US			300
 
 /* Runtime_pm autosuspend delay */
 #define CQSPI_AUTOSUSPEND_TIMEOUT		2000
@@ -148,12 +161,14 @@ struct cqspi_driver_platdata {
 /* Register map */
 #define CQSPI_REG_CONFIG			0x00
 #define CQSPI_REG_CONFIG_ENABLE_MASK		BIT(0)
+#define CQSPI_REG_CONFIG_PHY_EN			BIT(3)
 #define CQSPI_REG_CONFIG_ENB_DIR_ACC_CTRL	BIT(7)
 #define CQSPI_REG_CONFIG_DECODE_MASK		BIT(9)
 #define CQSPI_REG_CONFIG_CHIPSELECT_LSB		10
 #define CQSPI_REG_CONFIG_DMA_MASK		BIT(15)
 #define CQSPI_REG_CONFIG_BAUD_LSB		19
 #define CQSPI_REG_CONFIG_DTR_PROTO		BIT(24)
+#define CQSPI_REG_CONFIG_PHY_PIPELINE		BIT(25)
 #define CQSPI_REG_CONFIG_DUAL_OPCODE		BIT(30)
 #define CQSPI_REG_CONFIG_IDLE_LSB		31
 #define CQSPI_REG_CONFIG_CHIPSELECT_MASK	0xF
@@ -192,6 +207,7 @@ struct cqspi_driver_platdata {
 #define CQSPI_REG_READCAPTURE_BYPASS_LSB	0
 #define CQSPI_REG_READCAPTURE_DELAY_LSB		1
 #define CQSPI_REG_READCAPTURE_DELAY_MASK	0xF
+#define CQSPI_REG_READCAPTURE_EDGE_LSB		5
 #define CQSPI_REG_READCAPTURE_DQS_LSB		8
 
 #define CQSPI_REG_SIZE				0x14
@@ -273,6 +289,27 @@ struct cqspi_driver_platdata {
 #define CQSPI_REG_POLLING_STATUS		0xB0
 #define CQSPI_REG_POLLING_STATUS_DUMMY_LSB	16
 
+#define CQSPI_REG_PHY_CONFIG			0xB4
+#define CQSPI_REG_PHY_CONFIG_RX_DEL_LSB		0
+#define CQSPI_REG_PHY_CONFIG_RX_DEL_MASK	0x7F
+#define CQSPI_REG_PHY_CONFIG_TX_DEL_LSB		16
+#define CQSPI_REG_PHY_CONFIG_TX_DEL_MASK	0x7F
+#define CQSPI_REG_PHY_CONFIG_DLL_RESET		BIT(30)
+#define CQSPI_REG_PHY_CONFIG_RESYNC		BIT(31)
+
+#define CQSPI_REG_PHY_DLL_MASTER		0xB8
+#define CQSPI_REG_PHY_DLL_MASTER_INIT_DELAY_LSB	0
+#define CQSPI_REG_PHY_DLL_MASTER_INIT_DELAY_VAL	16
+#define CQSPI_REG_PHY_DLL_MASTER_DLY_ELMTS_LEN	0x7
+#define CQSPI_REG_PHY_DLL_MASTER_DLY_ELMTS_LSB	20
+#define CQSPI_REG_PHY_DLL_MASTER_DLY_ELMTS_3	0x2
+#define CQSPI_REG_PHY_DLL_MASTER_BYPASS		BIT(23)
+#define CQSPI_REG_PHY_DLL_MASTER_CYCLE		BIT(24)
+
+#define CQSPI_REG_DLL_OBS_LOW			0xBC
+#define CQSPI_REG_DLL_OBS_LOW_DLL_LOCK		BIT(0)
+#define CQSPI_REG_DLL_OBS_LOW_LOOPBACK_LOCK	BIT(15)
+
 #define CQSPI_REG_OP_EXT_LOWER			0xE0
 #define CQSPI_REG_OP_EXT_READ_LSB		24
 #define CQSPI_REG_OP_EXT_WRITE_LSB		16
@@ -321,6 +358,50 @@ struct cqspi_driver_platdata {
 
 #define CQSPI_REG_VERSAL_DMA_VAL		0x602
 
+#define CQSPI_PHY_INIT_RD			1
+#define CQSPI_PHY_MAX_RD			4
+#define CQSPI_PHY_MAX_DELAY			127
+#define CQSPI_PHY_DDR_SEARCH_STEP		4
+#define CQSPI_PHY_TX_LOOKUP_LOW_START		28
+#define CQSPI_PHY_TX_LOOKUP_LOW_END		48
+#define CQSPI_PHY_TX_LOOKUP_HIGH_START		60
+#define CQSPI_PHY_TX_LOOKUP_HIGH_END		96
+#define CQSPI_PHY_RX_LOW_SEARCH_START		0
+#define CQSPI_PHY_RX_LOW_SEARCH_END		40
+#define CQSPI_PHY_RX_HIGH_SEARCH_START		24
+#define CQSPI_PHY_RX_HIGH_SEARCH_END		127
+#define CQSPI_PHY_TX_LOW_SEARCH_START		0
+#define CQSPI_PHY_TX_LOW_SEARCH_END		64
+#define CQSPI_PHY_TX_HIGH_SEARCH_START		78
+#define CQSPI_PHY_TX_HIGH_SEARCH_END		127
+#define CQSPI_PHY_SEARCH_OFFSET			8
+
+#define CQSPI_PHY_DEFAULT_TEMP			45
+#define CQSPI_PHY_MIN_TEMP			-45
+#define CQSPI_PHY_MAX_TEMP			130
+#define CQSPI_PHY_MID_TEMP			(CQSPI_PHY_MIN_TEMP +	\
+						 ((CQSPI_PHY_MAX_TEMP -	\
+						   CQSPI_PHY_MIN_TEMP) / 2))
+
+/*
+ * PHY tuning pattern for calibrating read data capture delay. This 128-byte
+ * pattern provides sufficient bit transitions across all byte lanes to
+ * reliably detect timing windows at high frequencies.
+ */
+static const u8 phy_tuning_pattern[] __aligned(64) = {
+	0xFE, 0xFF, 0x01, 0x01, 0x01, 0x01, 0x01, 0x00, 0x00, 0xFE, 0xFE, 0x01,
+	0x01, 0x01, 0x01, 0x00, 0x00, 0xFE, 0xFE, 0x01, 0xFF, 0xFF, 0xFF, 0xFF,
+	0xFF, 0x00, 0x00, 0xFE, 0xFE, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x00, 0xFE,
+	0xFE, 0xFF, 0x01, 0x01, 0x01, 0x01, 0x01, 0xFE, 0x00, 0xFE, 0xFE, 0x01,
+	0x01, 0x01, 0x01, 0xFE, 0x00, 0xFE, 0xFE, 0x01, 0xFF, 0xFF, 0xFF, 0xFF,
+	0xFF, 0xFE, 0x00, 0xFE, 0xFE, 0xFF, 0xFF, 0xFF, 0xFF, 0xFE, 0x00, 0xFE,
+	0xFE, 0xFF, 0x01, 0x01, 0x01, 0x01, 0x01, 0x00, 0xFE, 0xFE, 0xFE, 0x01,
+	0x01, 0x01, 0x01, 0x00, 0xFE, 0xFE, 0xFE, 0x01, 0xFF, 0xFF, 0xFF, 0xFF,
+	0xFF, 0x00, 0xFE, 0xFE, 0xFE, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0xFE, 0xFE,
+	0xFE, 0xFF, 0x01, 0x01, 0x01, 0x01, 0x01, 0xFE, 0xFE, 0xFE, 0xFE, 0x01,
+	0x01, 0x01, 0x01, 0xFE, 0xFE, 0xFE, 0xFE, 0x01,
+};
+
 static int cqspi_wait_for_bit(const struct cqspi_driver_platdata *ddata,
 			      void __iomem *reg, const u32 mask, bool clr,
 			      bool busywait)
@@ -1555,6 +1636,1678 @@ static bool cqspi_supports_mem_op(struct spi_mem *mem,
 	return spi_mem_default_supports_op(mem, op);
 }
 
+static int cqspi_write_pattern_to_cache(struct cqspi_flash_pdata *f_pdata,
+					struct spi_mem *mem,
+					struct spi_mem_op *write_op)
+{
+	struct device *dev = &f_pdata->cqspi->pdev->dev;
+	int ret;
+
+	write_op->data.nbytes = sizeof(phy_tuning_pattern);
+	write_op->data.buf.out = phy_tuning_pattern;
+
+	ret = spi_mem_exec_op(mem, write_op);
+	if (ret) {
+		dev_err(dev, "Failed to write PHY pattern to cache: %d\n", ret);
+		return ret;
+	}
+	dev_dbg(dev, "PHY pattern (%zu bytes) written to cache\n",
+		sizeof(phy_tuning_pattern));
+
+	return 0;
+}
+
+static int cqspi_get_phy_pattern_offset(struct device *dev, u32 *offset)
+{
+	struct device_node *np, *flash_np = NULL, *part_np;
+	const __be32 *reg;
+	int len;
+
+	if (!dev || !dev->of_node)
+		return -EINVAL;
+
+	for_each_child_of_node(dev->of_node, np) {
+		if (of_node_name_prefix(np, "flash")) {
+			flash_np = np;
+			break;
+		}
+	}
+
+	if (!flash_np)
+		return -ENODEV;
+
+	part_np = of_parse_phandle(flash_np, "spi-phy-pattern-partition", 0);
+	of_node_put(flash_np);
+	if (!part_np)
+		return -ENODEV;
+
+	reg = of_get_property(part_np, "reg", &len);
+	if (reg && len >= sizeof(__be32)) {
+		*offset = be32_to_cpu(reg[0]);
+		of_node_put(part_np);
+		return 0;
+	}
+
+	of_node_put(part_np);
+	return -ENOENT;
+}
+
+static int cqspi_phy_check_pattern(struct cqspi_flash_pdata *f_pdata,
+				   struct spi_mem *mem)
+{
+	struct spi_mem_op op;
+	u8 *read_data;
+	int ret;
+
+	read_data = kmalloc_array(ARRAY_SIZE(phy_tuning_pattern),
+				  sizeof(phy_tuning_pattern[0]), GFP_KERNEL);
+	if (!read_data)
+		return -ENOMEM;
+
+	op = f_pdata->phy_read_op;
+	op.data.buf.in = read_data;
+	op.data.nbytes = sizeof(phy_tuning_pattern);
+
+	ret = spi_mem_exec_op(mem, &op);
+	if (ret)
+		goto out;
+
+	if (memcmp(read_data, phy_tuning_pattern, sizeof(phy_tuning_pattern)))
+		ret = -EAGAIN;
+
+out:
+	kfree(read_data);
+	return ret;
+}
+
+static void cqspi_phy_set_dll_master(struct cqspi_st *cqspi)
+{
+	void __iomem *reg_base = cqspi->iobase;
+	unsigned int reg;
+
+	reg = readl(reg_base + CQSPI_REG_PHY_DLL_MASTER);
+	reg &= ~((CQSPI_REG_PHY_DLL_MASTER_DLY_ELMTS_LEN
+		  << CQSPI_REG_PHY_DLL_MASTER_DLY_ELMTS_LSB) |
+		 CQSPI_REG_PHY_DLL_MASTER_BYPASS |
+		 CQSPI_REG_PHY_DLL_MASTER_CYCLE);
+	reg |= ((CQSPI_REG_PHY_DLL_MASTER_DLY_ELMTS_3
+		 << CQSPI_REG_PHY_DLL_MASTER_DLY_ELMTS_LSB) |
+		CQSPI_REG_PHY_DLL_MASTER_CYCLE);
+
+	writel(reg, reg_base + CQSPI_REG_PHY_DLL_MASTER);
+}
+
+static void cqspi_phy_pre_config(struct cqspi_st *cqspi,
+				 struct cqspi_flash_pdata *f_pdata,
+				 const bool bypass)
+{
+	void __iomem *reg_base = cqspi->iobase;
+	unsigned int reg;
+	u8 dummy;
+
+	cqspi_readdata_capture(cqspi, bypass, f_pdata->use_dqs,
+			       f_pdata->phy_setting.read_delay);
+
+	reg = readl(reg_base + CQSPI_REG_CONFIG);
+	reg &= ~(CQSPI_REG_CONFIG_PHY_EN | CQSPI_REG_CONFIG_PHY_PIPELINE);
+	reg |= CQSPI_REG_CONFIG_PHY_EN;
+	writel(reg, reg_base + CQSPI_REG_CONFIG);
+
+	reg = readl(reg_base + CQSPI_REG_RD_INSTR);
+	dummy = FIELD_GET(CQSPI_REG_RD_INSTR_DUMMY_MASK
+				  << CQSPI_REG_RD_INSTR_DUMMY_LSB,
+			  reg);
+	dummy--;
+	reg &= ~(CQSPI_REG_RD_INSTR_DUMMY_MASK << CQSPI_REG_RD_INSTR_DUMMY_LSB);
+	reg |= FIELD_PREP(CQSPI_REG_RD_INSTR_DUMMY_MASK
+				  << CQSPI_REG_RD_INSTR_DUMMY_LSB,
+			  dummy);
+	writel(reg, reg_base + CQSPI_REG_RD_INSTR);
+
+	cqspi_phy_set_dll_master(cqspi);
+}
+
+static void cqspi_phy_post_config(struct cqspi_st *cqspi,
+				  const unsigned int delay)
+{
+	void __iomem *reg_base = cqspi->iobase;
+	unsigned int reg;
+	u8 dummy;
+
+	reg = readl(reg_base + CQSPI_REG_READCAPTURE);
+	reg &= ~(CQSPI_REG_READCAPTURE_DELAY_MASK
+		 << CQSPI_REG_READCAPTURE_DELAY_LSB);
+
+	reg |= (delay & CQSPI_REG_READCAPTURE_DELAY_MASK)
+	       << CQSPI_REG_READCAPTURE_DELAY_LSB;
+	writel(reg, reg_base + CQSPI_REG_READCAPTURE);
+
+	reg = readl(reg_base + CQSPI_REG_CONFIG);
+	reg &= ~(CQSPI_REG_CONFIG_PHY_EN | CQSPI_REG_CONFIG_PHY_PIPELINE);
+	writel(reg, reg_base + CQSPI_REG_CONFIG);
+
+	reg = readl(reg_base + CQSPI_REG_RD_INSTR);
+	dummy = FIELD_GET(CQSPI_REG_RD_INSTR_DUMMY_MASK
+				  << CQSPI_REG_RD_INSTR_DUMMY_LSB,
+			  reg);
+	dummy++;
+	reg &= ~(CQSPI_REG_RD_INSTR_DUMMY_MASK << CQSPI_REG_RD_INSTR_DUMMY_LSB);
+	reg |= FIELD_PREP(CQSPI_REG_RD_INSTR_DUMMY_MASK
+				  << CQSPI_REG_RD_INSTR_DUMMY_LSB,
+			  dummy);
+	writel(reg, reg_base + CQSPI_REG_RD_INSTR);
+}
+
+static void cqspi_set_dll(void __iomem *reg_base, u8 rx_dll, u8 tx_dll)
+{
+	unsigned int reg;
+
+	reg = readl(reg_base + CQSPI_REG_PHY_CONFIG);
+	reg &= ~((CQSPI_REG_PHY_CONFIG_RX_DEL_MASK
+		  << CQSPI_REG_PHY_CONFIG_RX_DEL_LSB) |
+		 (CQSPI_REG_PHY_CONFIG_TX_DEL_MASK
+		  << CQSPI_REG_PHY_CONFIG_TX_DEL_LSB));
+	reg |= ((rx_dll & CQSPI_REG_PHY_CONFIG_RX_DEL_MASK)
+		<< CQSPI_REG_PHY_CONFIG_RX_DEL_LSB) |
+	       ((tx_dll & CQSPI_REG_PHY_CONFIG_TX_DEL_MASK)
+		<< CQSPI_REG_PHY_CONFIG_TX_DEL_LSB) |
+	       CQSPI_REG_PHY_CONFIG_RESYNC;
+	writel(reg, reg_base + CQSPI_REG_PHY_CONFIG);
+}
+
+static int cqspi_resync_dll(struct cqspi_st *cqspi)
+{
+	void __iomem *reg_base = cqspi->iobase;
+	unsigned int reg;
+	int ret;
+
+	ret = cqspi_wait_idle(cqspi);
+	if (ret)
+		return ret;
+
+	reg = readl(reg_base + CQSPI_REG_CONFIG);
+	reg &= ~CQSPI_REG_CONFIG_ENABLE_MASK;
+	writel(reg, reg_base + CQSPI_REG_CONFIG);
+
+	reg = readl(reg_base + CQSPI_REG_PHY_CONFIG);
+	reg &= ~(CQSPI_REG_PHY_CONFIG_DLL_RESET | CQSPI_REG_PHY_CONFIG_RESYNC);
+	writel(reg, reg_base + CQSPI_REG_PHY_CONFIG);
+
+	reg = readl(reg_base + CQSPI_REG_PHY_DLL_MASTER);
+	reg |= (CQSPI_REG_PHY_DLL_MASTER_INIT_DELAY_VAL
+		<< CQSPI_REG_PHY_DLL_MASTER_INIT_DELAY_LSB);
+	writel(reg, reg_base + CQSPI_REG_PHY_DLL_MASTER);
+
+	reg = readl(reg_base + CQSPI_REG_PHY_CONFIG);
+	reg |= CQSPI_REG_PHY_CONFIG_DLL_RESET;
+	writel(reg, reg_base + CQSPI_REG_PHY_CONFIG);
+
+	ret = readl_poll_timeout(reg_base + CQSPI_REG_DLL_OBS_LOW, reg,
+				 (reg & CQSPI_REG_DLL_OBS_LOW_DLL_LOCK), 0,
+				 CQSPI_DLL_TIMEOUT_US);
+	if (ret)
+		goto re_enable;
+
+	ret = readl_poll_timeout(reg_base + CQSPI_REG_DLL_OBS_LOW, reg,
+				 (reg & CQSPI_REG_DLL_OBS_LOW_LOOPBACK_LOCK), 0,
+				 CQSPI_DLL_TIMEOUT_US);
+	if (ret)
+		goto re_enable;
+
+	reg = readl(reg_base + CQSPI_REG_PHY_CONFIG);
+	reg |= CQSPI_REG_PHY_CONFIG_RESYNC;
+	writel(reg, reg_base + CQSPI_REG_PHY_CONFIG);
+
+re_enable:
+	reg = readl(reg_base + CQSPI_REG_CONFIG);
+	reg |= CQSPI_REG_CONFIG_ENABLE_MASK;
+	writel(reg, reg_base + CQSPI_REG_CONFIG);
+
+	return ret;
+}
+
+static int cqspi_phy_apply_setting(struct cqspi_flash_pdata *f_pdata,
+				   struct phy_setting *phy)
+{
+	struct cqspi_st *cqspi = f_pdata->cqspi;
+	unsigned int reg;
+	int ret;
+
+	reg = readl(cqspi->iobase + CQSPI_REG_READCAPTURE);
+	reg |= BIT(CQSPI_REG_READCAPTURE_EDGE_LSB);
+	writel(reg, cqspi->iobase + CQSPI_REG_READCAPTURE);
+
+	cqspi_set_dll(cqspi->iobase, phy->rx, phy->tx);
+
+	ret = cqspi_resync_dll(cqspi);
+	if (ret)
+		return ret;
+
+	f_pdata->phy_setting.read_delay = phy->read_delay;
+	return 0;
+}
+
+static int cqspi_find_rx_low_ddr(struct cqspi_flash_pdata *f_pdata,
+				 struct spi_mem *mem, struct phy_setting *phy)
+{
+	struct device *dev = &f_pdata->cqspi->pdev->dev;
+	int ret;
+
+	do {
+		phy->rx = CQSPI_PHY_RX_LOW_SEARCH_START;
+		do {
+			ret = cqspi_phy_apply_setting(f_pdata, phy);
+			if (!ret) {
+				ret = cqspi_phy_check_pattern(f_pdata, mem);
+				if (!ret)
+					return 0;
+			}
+
+			phy->rx += CQSPI_PHY_DDR_SEARCH_STEP;
+		} while (phy->rx <= CQSPI_PHY_RX_LOW_SEARCH_END);
+
+		phy->read_delay++;
+	} while (phy->read_delay <= CQSPI_PHY_MAX_RD);
+
+	dev_dbg(dev, "Unable to find RX low\n");
+	return -ENOENT;
+}
+
+static int cqspi_find_rx_low_sdr(struct cqspi_flash_pdata *f_pdata,
+				 struct spi_mem *mem, struct phy_setting *phy)
+{
+	struct device *dev = &f_pdata->cqspi->pdev->dev;
+	int ret;
+
+	phy->rx = 0;
+	do {
+		ret = cqspi_phy_apply_setting(f_pdata, phy);
+		if (!ret) {
+			ret = cqspi_phy_check_pattern(f_pdata, mem);
+			if (!ret)
+				return 0;
+		}
+		phy->rx++;
+	} while (phy->rx <= CQSPI_PHY_MAX_DELAY);
+
+	dev_dbg(dev, "Unable to find RX low\n");
+	return -ENOENT;
+}
+
+static int cqspi_find_rx_high_ddr(struct cqspi_flash_pdata *f_pdata,
+				  struct spi_mem *mem, struct phy_setting *phy)
+{
+	struct device *dev = &f_pdata->cqspi->pdev->dev;
+	int ret;
+
+	do {
+		phy->rx = CQSPI_PHY_RX_HIGH_SEARCH_END;
+		do {
+			ret = cqspi_phy_apply_setting(f_pdata, phy);
+			if (!ret) {
+				ret = cqspi_phy_check_pattern(f_pdata, mem);
+				if (!ret)
+					return 0;
+			}
+
+			phy->rx -= CQSPI_PHY_DDR_SEARCH_STEP;
+		} while (phy->rx >= CQSPI_PHY_RX_HIGH_SEARCH_START);
+
+		phy->read_delay--;
+	} while (phy->read_delay >= CQSPI_PHY_INIT_RD);
+
+	dev_dbg(dev, "Unable to find RX high\n");
+	return -ENOENT;
+}
+
+static int cqspi_find_rx_high_sdr(struct cqspi_flash_pdata *f_pdata,
+				  struct spi_mem *mem, struct phy_setting *phy,
+				  u8 lowerbound)
+{
+	struct device *dev = &f_pdata->cqspi->pdev->dev;
+	int ret;
+
+	phy->rx = CQSPI_PHY_MAX_DELAY;
+	do {
+		ret = cqspi_phy_apply_setting(f_pdata, phy);
+		if (!ret) {
+			ret = cqspi_phy_check_pattern(f_pdata, mem);
+			if (!ret)
+				return 0;
+		}
+		phy->rx--;
+	} while (phy->rx > lowerbound);
+
+	dev_dbg(dev, "Unable to find RX high\n");
+	return -ENOENT;
+}
+
+static int cqspi_find_tx_low_ddr(struct cqspi_flash_pdata *f_pdata,
+				 struct spi_mem *mem, struct phy_setting *phy)
+{
+	struct device *dev = &f_pdata->cqspi->pdev->dev;
+	int ret;
+
+	do {
+		phy->tx = CQSPI_PHY_TX_LOW_SEARCH_START;
+		do {
+			ret = cqspi_phy_apply_setting(f_pdata, phy);
+			if (!ret) {
+				ret = cqspi_phy_check_pattern(f_pdata, mem);
+				if (!ret)
+					return 0;
+			}
+
+			phy->tx += CQSPI_PHY_DDR_SEARCH_STEP;
+		} while (phy->tx <= CQSPI_PHY_TX_LOW_SEARCH_END);
+
+		phy->read_delay++;
+	} while (phy->read_delay <= CQSPI_PHY_MAX_RD);
+
+	dev_dbg(dev, "Unable to find TX low\n");
+	return -ENOENT;
+}
+
+static int cqspi_find_tx_high_ddr(struct cqspi_flash_pdata *f_pdata,
+				  struct spi_mem *mem, struct phy_setting *phy)
+{
+	struct device *dev = &f_pdata->cqspi->pdev->dev;
+	int ret;
+
+	do {
+		phy->tx = CQSPI_PHY_TX_HIGH_SEARCH_END;
+		do {
+			ret = cqspi_phy_apply_setting(f_pdata, phy);
+			if (!ret) {
+				ret = cqspi_phy_check_pattern(f_pdata, mem);
+				if (!ret)
+					return 0;
+			}
+
+			phy->tx -= CQSPI_PHY_DDR_SEARCH_STEP;
+		} while (phy->tx >= CQSPI_PHY_TX_HIGH_SEARCH_START);
+
+		phy->read_delay--;
+	} while (phy->read_delay >= CQSPI_PHY_INIT_RD);
+
+	dev_dbg(dev, "Unable to find TX high\n");
+	return -ENOENT;
+}
+
+static void cqspi_phy_find_gaplow_ddr(struct cqspi_flash_pdata *f_pdata,
+				      struct spi_mem *mem,
+				      struct phy_setting *bottomleft,
+				      struct phy_setting *topright,
+				      struct phy_setting *gaplow)
+{
+	struct phy_setting left, right, mid;
+	int ret;
+
+	left = *bottomleft;
+	right = *topright;
+
+	mid.tx = left.tx + ((right.tx - left.tx) / 2);
+	mid.rx = left.rx + ((right.rx - left.rx) / 2);
+	mid.read_delay = left.read_delay;
+
+	do {
+		ret = cqspi_phy_apply_setting(f_pdata, &mid);
+		if (!ret)
+			ret = cqspi_phy_check_pattern(f_pdata, mem);
+
+		if (ret) {
+			/* The pattern was not found. Go to the lower half. */
+			right.tx = mid.tx;
+			right.rx = mid.rx;
+
+			mid.tx = left.tx + ((mid.tx - left.tx) / 2);
+			mid.rx = left.rx + ((mid.rx - left.rx) / 2);
+		} else {
+			/* The pattern was found. Go to the upper half. */
+			left.tx = mid.tx;
+			left.rx = mid.rx;
+
+			mid.tx = mid.tx + ((right.tx - mid.tx) / 2);
+			mid.rx = mid.rx + ((right.rx - mid.rx) / 2);
+		}
+
+		/* Break the loop if the window has closed. */
+	} while ((right.tx - left.tx >= 2) && (right.rx - left.rx >= 2));
+
+	*gaplow = mid;
+}
+
+static void cqspi_phy_find_gaphigh_ddr(struct cqspi_flash_pdata *f_pdata,
+				       struct spi_mem *mem,
+				       struct phy_setting *bottomleft,
+				       struct phy_setting *topright,
+				       struct phy_setting *gaphigh)
+{
+	struct phy_setting left, right, mid;
+	int ret;
+
+	left = *bottomleft;
+	right = *topright;
+
+	mid.tx = left.tx + ((right.tx - left.tx) / 2);
+	mid.rx = left.rx + ((right.rx - left.rx) / 2);
+	mid.read_delay = right.read_delay;
+
+	do {
+		ret = cqspi_phy_apply_setting(f_pdata, &mid);
+		if (!ret)
+			ret = cqspi_phy_check_pattern(f_pdata, mem);
+
+		if (ret) {
+			/* The pattern was not found. Go to the upper half. */
+			left.tx = mid.tx;
+			left.rx = mid.rx;
+
+			mid.tx = mid.tx + ((right.tx - mid.tx) / 2);
+			mid.rx = mid.rx + ((right.rx - mid.rx) / 2);
+		} else {
+			/* The pattern was found. Go to the lower half. */
+			right.tx = mid.tx;
+			right.rx = mid.rx;
+
+			mid.tx = left.tx + ((mid.tx - left.tx) / 2);
+			mid.rx = left.rx + ((mid.rx - left.rx) / 2);
+		}
+
+		/* Break the loop if the window has closed. */
+	} while ((right.tx - left.tx >= 2) && (right.rx - left.rx >= 2));
+
+	*gaphigh = mid;
+}
+
+static int cqspi_get_temp(int *temp)
+{
+	/* TODO: read SoC thermal sensor; caller falls back to room temperature */
+	return -EOPNOTSUPP;
+}
+
+static inline void cqspi_phy_reset_setting(struct phy_setting *phy)
+{
+	*phy = (struct phy_setting){ .rx = 0, .tx = 127, .read_delay = 0 };
+}
+
+static int cqspi_phy_tuning_ddr(struct cqspi_flash_pdata *f_pdata,
+				struct spi_mem *mem)
+{
+	struct cqspi_st *cqspi = f_pdata->cqspi;
+	struct device *dev = &cqspi->pdev->dev;
+	struct phy_setting rxlow, rxhigh, txlow, txhigh;
+	struct phy_setting srxlow, srxhigh;
+	struct phy_setting bottomleft, topright, searchpoint;
+	struct phy_setting gaplow, gaphigh;
+	struct phy_setting backuppoint, backupcornerpoint;
+	int ret, rx_window, temp;
+	bool primary = true, secondary = true;
+
+	/*
+	 * DDR tuning: 2D search across RX and TX delays for optimal timing.
+	 *
+	 * Algorithm: Find RX boundaries (rxlow/rxhigh) using TX window search,
+	 * find TX boundaries (txlow/txhigh) at fixed RX, define valid region,
+	 * locate gaps via binary search, select final point with temperature
+	 * compensation.
+	 *
+	 *              rx
+	 *          127 ^
+	 *              |                                 topright
+	 *              |                                    *
+	 *              |       xxxxx     ++++++++++++++++++++
+	 *              |       xxxxxx     +++++++++++++++++++
+	 *              |       xxxxxxx     ++++++++++++++++++
+	 *              |       xxxxxxxx     +++++++++++++++++
+	 *              |       xxxxxxxxx     ++++++++++++++++
+	 *              |       xxxxxxxxxx     +++++++++++++++
+	 *              |       xxxxxxxxxxx     ++++++++++++++
+	 *              |       xxxxxxxxxxxx     +++++++++++++
+	 *              |       xxxxxxxxxxxxx     ++++++++++++
+	 *              |       xxxxxxxxxxxxxx     +++++++++++
+	 *              |       xxxxxxxxxxxxxxx     ++++++++++
+	 *              |       xxxxxxxxxxxxxxxx     +++++++++
+	 *              |       xxxxxxxxxxxxxxxxx     ++++++++
+	 *              |       xxxxxxxxxxxxxxxxxx     +++++++
+	 *              |       *
+	 *              |  bottomleft
+	 *              -----------------------------------------> tx
+	 *              0                                      127
+	 */
+
+	f_pdata->use_tuned_phy = true;
+
+	/* Golden rxlow search: Find lower RX boundary using TX window sweep */
+
+	/*
+	 *              rx
+	 *          127 ^
+	 *              |       xxxxx     ++++++++++++++++++++
+	 *              |       xxxxxx     +++++++++++++++++++
+	 *              |       xxxxxxx     ++++++++++++++++++
+	 *              |       xxxxxxxx     +++++++++++++++++
+	 *              |       xxxxxxxxx     ++++++++++++++++
+	 *              |       xxxxxxxxxx     +++++++++++++++
+	 *              |       xxxxxxxxxxx     ++++++++++++++
+	 *              |       |xxxxx|xxxxx     +++++++++++++
+	 *              |       |xxxxx|xxxxxx     ++++++++++++
+	 *      search  |       |xxxxx|xxxxxxx     +++++++++++
+	 *      rxlow --------->|xxxxx|xxxxxxxx     ++++++++++
+	 *              |       |xxxxx|xxxxxxxxx     +++++++++
+	 *              |       |xxxxx|xxxxxxxxxx     ++++++++
+	 *              |       |xxxxx|xxxxxxxxxxx     +++++++
+	 *              |       |     |
+	 *              --------|-----|----------------------------> tx
+	 *              0       |     |                          127
+	 *                  txlow     txlow
+	 *                  start     end
+	 *
+	 *      |----------------------------------------------------------|
+	 *      | Primary | Secondary | Final                              |
+	 *      | Search  | Search    | Point                              |
+	 *      |---------|-----------|------------------------------------|
+	 *      | Fail    | Fail      | Return Fail                        |
+	 *      |---------|-----------|------------------------------------|
+	 *      | Fail    | Pass      | Return Fail                        |
+	 *      |---------|-----------|------------------------------------|
+	 *      | Pass    | Fail      | Return Fail                        |
+	 *      |---------|-----------|------------------------------------|
+	 *      | Pass    | Pass      | rx = min(primary.rx, secondary.rx) |
+	 *      |         |           | tx = primary.tx                    |
+	 *      |         |           | read_delay =                       |
+	 *      |         |           |         min(primary.read_delay,    |
+	 *      |         |           |             secondary.read_delay)  |
+	 *      |----------------------------------------------------------|
+	 */
+
+	/* Primary rxlow: Sweep TX window to find valid RX lower bound */
+
+	rxlow.tx = CQSPI_PHY_TX_LOOKUP_LOW_START;
+	do {
+		dev_dbg(dev, "Searching for Golden Primary rxlow on TX = %d\n",
+			rxlow.tx);
+		rxlow.read_delay = CQSPI_PHY_INIT_RD;
+		ret = cqspi_find_rx_low_ddr(f_pdata, mem, &rxlow);
+		rxlow.tx += CQSPI_PHY_DDR_SEARCH_STEP;
+	} while (ret && rxlow.tx <= CQSPI_PHY_TX_LOOKUP_LOW_END);
+	if (ret)
+		goto out;
+	dev_dbg(dev, "Golden Primary rxlow: RX: %d TX: %d RD: %d\n", rxlow.rx,
+		rxlow.tx, rxlow.read_delay);
+
+	/* Secondary rxlow: Verify at offset TX for robustness */
+
+	if (rxlow.tx <= (CQSPI_PHY_TX_LOOKUP_LOW_END - CQSPI_PHY_SEARCH_OFFSET))
+		srxlow.tx = rxlow.tx + CQSPI_PHY_SEARCH_OFFSET;
+	else
+		srxlow.tx = CQSPI_PHY_TX_LOOKUP_LOW_END;
+	dev_dbg(dev, "Searching for Golden Secondary rxlow on TX = %d\n",
+		srxlow.tx);
+	srxlow.read_delay = CQSPI_PHY_INIT_RD;
+	ret = cqspi_find_rx_low_ddr(f_pdata, mem, &srxlow);
+	if (ret)
+		goto out;
+	dev_dbg(dev, "Golden Secondary rxlow: RX: %d TX: %d RD: %d\n",
+		srxlow.rx, srxlow.tx, srxlow.read_delay);
+
+	rxlow.rx = min(rxlow.rx, srxlow.rx);
+	rxlow.read_delay = min(rxlow.read_delay, srxlow.read_delay);
+	dev_dbg(dev, "Golden Final rxlow: RX: %d TX: %d RD: %d\n", rxlow.rx,
+		rxlow.tx, rxlow.read_delay);
+
+	/* Golden rxhigh search: Find upper RX boundary at fixed TX */
+
+	/*
+	 *              rx
+	 *          127 ^
+	 *              |       |xxxx     ++++++++++++++++++++
+	 *              |       |xxxxx     +++++++++++++++++++
+	 *    search    |       |xxxxxx     ++++++++++++++++++
+	 *    rxhigh  --------->|xxxxxxx     +++++++++++++++++
+	 *    on fixed  |       |xxxxxxxx     ++++++++++++++++
+	 *    tx        |       |xxxxxxxxx     +++++++++++++++
+	 *              |       |xxxxxxxxxx     ++++++++++++++
+	 *              |       xxxxxxxxxxxx     +++++++++++++
+	 *              |       xxxxxxxxxxxxx     ++++++++++++
+	 *              |       xxxxxxxxxxxxxx     +++++++++++
+	 *              |       xxxxxxxxxxxxxxx     ++++++++++
+	 *              |       xxxxxxxxxxxxxxxx     +++++++++
+	 *              |       xxxxxxxxxxxxxxxxx     ++++++++
+	 *              |       xxxxxxxxxxxxxxxxxx     +++++++
+	 *              |
+	 *              -------------------------------------------> tx
+	 *              0                                        127
+	 *
+	 *      |----------------------------------------------------------|
+	 *      | Primary | Secondary | Final                              |
+	 *      | Search  | Search    | Point                              |
+	 *      |---------|-----------|------------------------------------|
+	 *      | Fail    | Fail      | Return Fail                        |
+	 *      |---------|-----------|------------------------------------|
+	 *      | Fail    | Pass      | Choose Secondary                   |
+	 *      |---------|-----------|------------------------------------|
+	 *      | Pass    | Fail      | Choose Primary                     |
+	 *      |---------|-----------|------------------------------------|
+	 *      | Pass    | Pass      | if (secondary.rx > primary.rx)     |
+	 *      |         |           |         Choose Secondary           |
+	 *      |         |           | else                               |
+	 *      |         |           |         Choose Primary             |
+	 *      |----------------------------------------------------------|
+	 */
+
+	/* Primary rxhigh: Search at rxlow's TX, decrement from max read_delay */
+
+	rxhigh.tx = rxlow.tx;
+	dev_dbg(dev, "Searching for Golden Primary rxhigh on TX = %d\n",
+		rxhigh.tx);
+	rxhigh.read_delay = CQSPI_PHY_MAX_RD;
+	ret = cqspi_find_rx_high_ddr(f_pdata, mem, &rxhigh);
+	if (ret)
+		primary = false;
+	dev_dbg(dev, "Golden Primary rxhigh: RX: %d TX: %d RD: %d\n", rxhigh.rx,
+		rxhigh.tx, rxhigh.read_delay);
+
+	/* Secondary rxhigh: Verify at offset TX */
+
+	if (rxhigh.tx <=
+	    (CQSPI_PHY_TX_LOOKUP_LOW_END - CQSPI_PHY_SEARCH_OFFSET))
+		srxhigh.tx = rxhigh.tx + CQSPI_PHY_SEARCH_OFFSET;
+	else
+		srxhigh.tx = CQSPI_PHY_TX_LOOKUP_LOW_END;
+	dev_dbg(dev, "Searching for Golden Secondary rxhigh on TX = %d\n",
+		srxhigh.tx);
+	srxhigh.read_delay = CQSPI_PHY_MAX_RD;
+	ret = cqspi_find_rx_high_ddr(f_pdata, mem, &srxhigh);
+	if (ret)
+		secondary = false;
+	dev_dbg(dev, "Golden Secondary rxhigh: RX: %d TX: %d RD: %d\n",
+		srxhigh.rx, srxhigh.tx, srxhigh.read_delay);
+
+	if (!primary && !secondary)
+		goto out;
+	else if (!primary)
+		rxhigh = srxhigh;
+	else if (secondary && srxhigh.rx > rxhigh.rx)
+		rxhigh = srxhigh;
+	dev_dbg(dev, "Golden Final rxhigh: RX: %d TX: %d RD: %d\n", rxhigh.rx,
+		rxhigh.tx, rxhigh.read_delay);
+
+	primary = true;
+	secondary = true;
+
+	/* If rxlow/rxhigh at same read_delay, search backup at upper TX range */
+
+	if (rxlow.read_delay == rxhigh.read_delay) {
+		dev_dbg(dev, "rxlow and rxhigh at the same read delay.\n");
+
+		/* Backup rxlow: Search at high TX window */
+
+		/*
+		 *              rx
+		 *          127 ^
+		 *              |       xxxxx     ++++++++++++++++++++
+		 *              |       xxxxxx     +++++++++++++++++++
+		 *              |       xxxxxxx     ++++++++++++++++++
+		 *              |       xxxxxxxx     +++++++++++++++++
+		 *              |       xxxxxxxxx     ++++++++++++++++
+		 *              |       xxxxxxxxxx     +++++++++++++++
+		 *              |       xxxxxxxxxxx     ++++++++++++++
+		 *              |       xxxxxxxxxxxx     +++++++|++++|
+		 *              |       xxxxxxxxxxxxx     ++++++|++++|
+		 *      search  |       xxxxxxxxxxxxxx     +++++|++++|
+		 *      rxlow --------------------------------->|++++|
+		 *              |       xxxxxxxxxxxxxxxx     +++|++++|
+		 *              |       xxxxxxxxxxxxxxxxx     ++|++++|
+		 *              |       xxxxxxxxxxxxxxxxxx     +|++++|
+		 *              |                               |    |
+		 *              --------------------------------|----|-----> tx
+		 *              0                               |    |   127
+		 *                                         txhigh    txhigh
+		 *                                          start    end
+		 *
+		 *      |-----------------------------------------------------|
+		 *      | Primary | Secondary | Final                         |
+		 *      | Search  | Search    | Point                         |
+		 *      |---------|-----------|-------------------------------|
+		 *      | Fail    | Fail      | Return Fail                   |
+		 *      |---------|-----------|-------------------------------|
+		 *      | Fail    | Pass      | Return Fail                   |
+		 *      |---------|-----------|-------------------------------|
+		 *      | Pass    | Fail      | Return Fail                   |
+		 *      |---------|-----------|-------------------------------|
+		 *      | Pass    | Pass      | rx =                          |
+		 *      |         |           |  min(primary.rx, secondary.rx)|
+		 *      |         |           | tx = primary.tx               |
+		 *      |         |           | read_delay =                  |
+		 *      |         |           |  min(primary.read_delay,      |
+		 *      |         |           |      secondary.read_delay)    |
+		 *      |-----------------------------------------------------|
+		 */
+
+		/* Primary backup: Decrement TX from high window end */
+
+		backuppoint.tx = CQSPI_PHY_TX_LOOKUP_HIGH_END;
+		do {
+			dev_dbg(dev,
+				"Searching for Backup Primary rxlow on TX = %d\n",
+				backuppoint.tx);
+			backuppoint.read_delay = CQSPI_PHY_INIT_RD;
+			ret = cqspi_find_rx_low_ddr(f_pdata, mem, &backuppoint);
+			backuppoint.tx -= CQSPI_PHY_DDR_SEARCH_STEP;
+		} while (ret &&
+			 backuppoint.tx >= CQSPI_PHY_TX_LOOKUP_HIGH_START);
+		if (ret)
+			goto out;
+		dev_dbg(dev, "Backup Primary rxlow: RX: %d TX: %d RD: %d\n",
+			backuppoint.rx, backuppoint.tx, backuppoint.read_delay);
+
+		/* Secondary backup: Verify at offset TX */
+
+		if (backuppoint.tx >=
+		    (CQSPI_PHY_TX_LOOKUP_HIGH_START + CQSPI_PHY_SEARCH_OFFSET))
+			srxlow.tx = backuppoint.tx - CQSPI_PHY_SEARCH_OFFSET;
+		else
+			srxlow.tx = CQSPI_PHY_TX_LOOKUP_HIGH_START;
+		dev_dbg(dev,
+			"Searching for Backup Secondary rxlow on TX = %d\n",
+			srxlow.tx);
+		srxlow.read_delay = CQSPI_PHY_INIT_RD;
+		ret = cqspi_find_rx_low_ddr(f_pdata, mem, &srxlow);
+		if (ret)
+			goto out;
+		dev_dbg(dev, "Backup Secondary rxlow: RX: %d TX: %d RD: %d\n",
+			srxlow.rx, srxlow.tx, srxlow.read_delay);
+
+		backuppoint.rx = min(backuppoint.rx, srxlow.rx);
+		backuppoint.read_delay =
+			min(backuppoint.read_delay, srxlow.read_delay);
+		dev_dbg(dev, "Backup Final rxlow: RX: %d TX: %d RD: %d\n",
+			backuppoint.rx, backuppoint.tx, backuppoint.read_delay);
+
+		if (backuppoint.rx < rxlow.rx) {
+			rxlow = backuppoint;
+			dev_dbg(dev, "Updating rxlow to the one at TX = %d\n",
+				backuppoint.tx);
+		}
+		dev_dbg(dev, "Final rxlow: RX: %d TX: %d RD: %d\n", rxlow.rx,
+			rxlow.tx, rxlow.read_delay);
+
+		/* Backup rxhigh: Search at fixed backup TX */
+
+		/*
+		 *              rx
+		 *          127 ^
+		 *              |       xxxxx     +++++++++++++++++++|
+		 *              |       xxxxxx     ++++++++++++++++++|
+		 *    search    |       xxxxxxx     +++++++++++++++++|
+		 *    rxhigh  -------------------------------------->|
+		 *    on fixed  |       xxxxxxxxx     +++++++++++++++|
+		 *    tx        |       xxxxxxxxxx     ++++++++++++++|
+		 *              |       xxxxxxxxxxx     +++++++++++++|
+		 *              |       xxxxxxxxxxxx     +++++++++++++
+		 *              |       xxxxxxxxxxxxx     ++++++++++++
+		 *              |       xxxxxxxxxxxxxx     +++++++++++
+		 *              |       xxxxxxxxxxxxxxx     ++++++++++
+		 *              |       xxxxxxxxxxxxxxxx     +++++++++
+		 *              |       xxxxxxxxxxxxxxxxx     ++++++++
+		 *              |       xxxxxxxxxxxxxxxxxx     +++++++
+		 *              |
+		 *              -------------------------------------------> tx
+		 *               0                                        127
+		 *
+		 *      |-----------------------------------------------------|
+		 *      | Primary | Secondary | Final                         |
+		 *      | Search  | Search    | Point                         |
+		 *      |---------|-----------|-------------------------------|
+		 *      | Fail    | Fail      | Return Fail                   |
+		 *      |---------|-----------|-------------------------------|
+		 *      | Fail    | Pass      | Choose Secondary              |
+		 *      |---------|-----------|-------------------------------|
+		 *      | Pass    | Fail      | Choose Primary                |
+		 *      |---------|-----------|-------------------------------|
+		 *      | Pass    | Pass      | if (secondary.rx > primary.rx)|
+		 *      |         |           |         Choose Secondary      |
+		 *      |         |           | else                          |
+		 *      |         |           |         Choose Primary        |
+		 *      |-----------------------------------------------------|
+		 */
+
+		/* Primary backup rxhigh: Use backup TX, decrement from max read_delay */
+
+		dev_dbg(dev, "Searching for Backup Primary rxhigh on TX = %d\n",
+			backuppoint.tx);
+		backuppoint.read_delay = CQSPI_PHY_MAX_RD;
+		ret = cqspi_find_rx_high_ddr(f_pdata, mem, &backuppoint);
+		if (ret)
+			primary = false;
+		dev_dbg(dev, "Backup Primary rxhigh: RX: %d TX: %d RD: %d\n",
+			backuppoint.rx, backuppoint.tx, backuppoint.read_delay);
+
+		/* Secondary backup rxhigh: Verify at offset TX */
+
+		if (backuppoint.tx >=
+		    (CQSPI_PHY_TX_LOOKUP_HIGH_START + CQSPI_PHY_SEARCH_OFFSET))
+			srxhigh.tx = backuppoint.tx - CQSPI_PHY_SEARCH_OFFSET;
+		else
+			srxhigh.tx = CQSPI_PHY_TX_LOOKUP_HIGH_START;
+		dev_dbg(dev,
+			"Searching for Backup Secondary rxhigh on TX = %d\n",
+			srxhigh.tx);
+		srxhigh.read_delay = CQSPI_PHY_MAX_RD;
+		ret = cqspi_find_rx_high_ddr(f_pdata, mem, &srxhigh);
+		if (ret)
+			secondary = false;
+		dev_dbg(dev, "Backup Secondary rxhigh: RX: %d TX: %d RD: %d\n",
+			srxhigh.rx, srxhigh.tx, srxhigh.read_delay);
+
+		if (!primary && !secondary)
+			goto out;
+		else if (!primary)
+			backuppoint = srxhigh;
+		else if (secondary && srxhigh.rx > backuppoint.rx)
+			backuppoint = srxhigh;
+		dev_dbg(dev, "Backup Final rxhigh: RX: %d TX: %d RD: %d\n",
+			backuppoint.rx, backuppoint.tx, backuppoint.read_delay);
+
+		if (backuppoint.rx > rxhigh.rx) {
+			rxhigh = backuppoint;
+			dev_dbg(dev, "Updating rxhigh to the one at TX = %d\n",
+				backuppoint.tx);
+		}
+		dev_dbg(dev, "Final rxhigh: RX: %d TX: %d RD: %d\n", rxhigh.rx,
+			rxhigh.tx, rxhigh.read_delay);
+	}
+
+	/* Golden txlow: Fix RX at 1/4 of RX window, search TX lower bound */
+
+	/*
+	 *              rx
+	 *          127 ^
+	 *              |
+	 *     rxhigh --------->xxxxx     ++++++++++++++++++++
+	 *              |       xxxxxx     +++++++++++++++++++
+	 *              |       xxxxxxx     ++++++++++++++++++
+	 *              |       xxxxxxxx     +++++++++++++++++
+	 *              |       xxxxxxxxx     ++++++++++++++++
+	 *              |       xxxxxxxxxx     +++++++++++++++
+	 *              |       xxxxxxxxxxx     ++++++++++++++
+	 *              |       xxxxxxxxxxxx     +++++++++++++
+	 *    fix rx    |       xxxxxxxxxxxxx     ++++++++++++
+	 *    1/4 b/w ---------><------->xxxxx     +++++++++++
+	 *    rxlow and |       xxxx|xxxxxxxxxx     ++++++++++
+	 *    rxhigh    |       xxxx|xxxxxxxxxxx     +++++++++
+	 *              |       xxxx|xxxxxxxxxxxx     ++++++++
+	 *      rxlow --------->xxxx|xxxxxxxxxxxxx     +++++++
+	 *              |           |
+	 *              ------------|------------------------------> tx
+	 *              0           |                            127
+	 *                     search
+	 *                      txlow
+	 */
+
+	rx_window = rxhigh.rx - rxlow.rx;
+	txlow.rx = rxlow.rx + (rx_window / 4);
+	dev_dbg(dev, "Searching for Golden txlow on RX = %d\n", txlow.rx);
+	txlow.read_delay = CQSPI_PHY_INIT_RD;
+	ret = cqspi_find_tx_low_ddr(f_pdata, mem, &txlow);
+	if (ret)
+		goto out;
+	dev_dbg(dev, "Golden txlow: RX: %d TX: %d RD: %d\n", txlow.rx, txlow.tx,
+		txlow.read_delay);
+
+	/* Golden txhigh: Same RX as txlow, decrement from max read_delay */
+
+	/*
+	 *              rx
+	 *          127 ^
+	 *              |
+	 *     rxhigh --------->xxxxx     ++++++++++++++++++++
+	 *              |       xxxxxx     +++++++++++++++++++
+	 *              |       xxxxxxx     ++++++++++++++++++
+	 *              |       xxxxxxxx     +++++++++++++++++
+	 *              |       xxxxxxxxx     ++++++++++++++++
+	 *              |       xxxxxxxxxx     +++++++++++++++
+	 *              |       xxxxxxxxxxx     ++++++++++++++
+	 *              |       xxxxxxxxxxxx     +++++++++++++
+	 *    fix rx    |       xxxxxxxxxxxxx     ++++++++++++
+	 *    1/4 b/w --------------------------------><----->
+	 *    rxlow and |       xxxxxxxxxxxxxxx     ++++++|+++
+	 *    rxhigh    |       xxxxxxxxxxxxxxxx     +++++|+++
+	 *              |       xxxxxxxxxxxxxxxxx     ++++|+++
+	 *      rxlow --------->xxxxxxxxxxxxxxxxxx     +++|+++
+	 *              |                                 |
+	 *              ----------------------------------|--------> tx
+	 *              0                                 |      127
+	 *                                           search
+	 *                                           txhigh
+	 */
+
+	txhigh.rx = txlow.rx;
+	dev_dbg(dev, "Searching for Golden txhigh on RX = %d\n", txhigh.rx);
+	txhigh.read_delay = CQSPI_PHY_MAX_RD;
+	ret = cqspi_find_tx_high_ddr(f_pdata, mem, &txhigh);
+	if (ret)
+		goto out;
+	dev_dbg(dev, "Golden txhigh: RX: %d TX: %d RD: %d\n", txhigh.rx,
+		txhigh.tx, txhigh.read_delay);
+
+	/* If txlow/txhigh at same read_delay, search backup at 3/4 RX window */
+
+	if (txlow.read_delay == txhigh.read_delay) {
+		/* Backup txlow: Fix RX at 3/4 of RX window */
+
+		/*
+		 *              rx
+		 *          127 ^
+		 *              |
+		 *     rxhigh --------->xxxxx     ++++++++++++++++++++
+		 *              |       xxxxxx     +++++++++++++++++++
+		 *    fix rx    |       xxxxxxx     ++++++++++++++++++
+		 *    3/4 b/w ---------><----->x     +++++++++++++++++
+		 *    rxlow and |       xxxx|xxxx     ++++++++++++++++
+		 *    rxhigh    |       xxxx|xxxxx     +++++++++++++++
+		 *              |       xxxx|xxxxxx     ++++++++++++++
+		 *              |       xxxx|xxxxxxx     +++++++++++++
+		 *              |       xxxx|xxxxxxxx     ++++++++++++
+		 *              |       xxxx|xxxxxxxxx     +++++++++++
+		 *              |       xxxx|xxxxxxxxxx     ++++++++++
+		 *              |       xxxx|xxxxxxxxxxx     +++++++++
+		 *              |       xxxx|xxxxxxxxxxxx     ++++++++
+		 *      rxlow --------->xxxx|xxxxxxxxxxxxx     +++++++
+		 *              |           |
+		 *              ------------|------------------------------> tx
+		 *              0           |                            127
+		 *                     search
+		 *                      txlow
+		 */
+
+		dev_dbg(dev, "txlow and txhigh at the same read delay.\n");
+		backuppoint.rx = rxlow.rx + ((rx_window * 3) / 4);
+		dev_dbg(dev, "Searching for Backup txlow on RX = %d\n",
+			backuppoint.rx);
+		backuppoint.read_delay = CQSPI_PHY_INIT_RD;
+		ret = cqspi_find_tx_low_ddr(f_pdata, mem, &backuppoint);
+		if (ret)
+			goto out;
+		dev_dbg(dev, "Backup txlow: RX: %d TX: %d RD: %d\n",
+			backuppoint.rx, backuppoint.tx, backuppoint.read_delay);
+
+		if (backuppoint.tx < txlow.tx) {
+			txlow = backuppoint;
+			dev_dbg(dev, "Updating txlow with the one at RX = %d\n",
+				backuppoint.rx);
+		}
+		dev_dbg(dev, "Final txlow: RX: %d TX: %d RD: %d\n", txlow.rx,
+			txlow.tx, txlow.read_delay);
+
+		/* Backup txhigh: Same RX as backup txlow, decrement from max */
+
+		/*
+		 *              rx
+		 *          127 ^
+		 *              |
+		 *     rxhigh --------->xxxxx     ++++++++++++++++++++
+		 *              |       xxxxxx     +++++++++++++++++++
+		 *    fix rx    |       xxxxxxx     ++++++++++++++++++
+		 *    3/4 b/w ------------------------------><------->
+		 *    rxlow and |       xxxxxxxxx     +++++++++++|++++
+		 *    rxhigh    |       xxxxxxxxxx     ++++++++++|++++
+		 *              |       xxxxxxxxxxx     +++++++++|++++
+		 *              |       xxxxxxxxxxxx     ++++++++|++++
+		 *              |       xxxxxxxxxxxxx     +++++++|++++
+		 *              |       xxxxxxxxxxxxxx     ++++++|++++
+		 *              |       xxxxxxxxxxxxxxx     +++++|++++
+		 *              |       xxxxxxxxxxxxxxxx     ++++|++++
+		 *              |       xxxxxxxxxxxxxxxxx     +++|++++
+		 *      rxlow --------->xxxxxxxxxxxxxxxxxx     ++|++++
+		 *              |                                |
+		 *              ---------------------------------|---------> tx
+		 *              0                                |       127
+		 *                                               search
+		 *                                               txhigh
+		 */
+
+		dev_dbg(dev, "Searching for Backup txhigh on RX = %d\n",
+			backuppoint.rx);
+		backuppoint.read_delay = CQSPI_PHY_MAX_RD;
+		ret = cqspi_find_tx_high_ddr(f_pdata, mem, &backuppoint);
+		if (ret)
+			goto out;
+		dev_dbg(dev, "Backup txhigh: RX: %d TX: %d RD: %d\n",
+			backuppoint.rx, backuppoint.tx, backuppoint.read_delay);
+
+		if (backuppoint.tx > txhigh.tx) {
+			txhigh = backuppoint;
+			dev_dbg(dev,
+				"Updating txhigh with the one at RX = %d\n",
+				backuppoint.rx);
+		}
+		dev_dbg(dev, "Final txhigh: RX: %d TX: %d RD: %d\n", txhigh.rx,
+			txhigh.tx, txhigh.read_delay);
+	}
+
+	/* Corner points: Define and verify bottomleft and topright boundaries */
+
+	/*
+	 *              rx
+	 *          127 ^
+	 *              |                                 topright
+	 *              |                                    *
+	 *    rxhigh -----------xxxxx     ++++++++++++++++++++
+	 *              |       xxxxxx     +++++++++++++++++++
+	 *              |       xxxxxxx     ++++++++++++++++++
+	 *              |       xxxxxxxx     +++++++++++++++++
+	 *              |       xxxxxxxxx     ++++++++++++++++
+	 *              |       xxxxxxxxxx     +++++++++++++++
+	 *              |       xxxxxxxxxxx     ++++++++++++++
+	 *              |       xxxxxxxxxxxx     +++++++++++++
+	 *              |       xxxxxxxxxxxxx     ++++++++++++
+	 *              |       xxxxxxxxxxxxxx     +++++++++++
+	 *              |       xxxxxxxxxxxxxxx     ++++++++++
+	 *              |       xxxxxxxxxxxxxxxx     +++++++++
+	 *              |       xxxxxxxxxxxxxxxxx     ++++++++
+	 *     rxlow -----------xxxxxxxxxxxxxxxxxx     +++++++
+	 *              |       *                            |
+	 *              | bottom|left                        |
+	 *              --------|----------------------------|---> tx
+	 *              0       |                            | 127
+	 *                      |                            |
+	 *                      txlow                   txhigh
+	 *
+	 * Verification: Test point 4 taps inside each corner, adjust
+	 * read_delay ±1 if needed to ensure valid corners for gap search.
+	 */
+
+	bottomleft.tx = txlow.tx;
+	bottomleft.rx = rxlow.rx;
+	if (txlow.read_delay <= rxlow.read_delay)
+		bottomleft.read_delay = txlow.read_delay;
+	else
+		bottomleft.read_delay = rxlow.read_delay;
+
+	/* Verify bottomleft: Test 4 taps inside, adjust read_delay if needed */
+	backupcornerpoint = bottomleft;
+	backupcornerpoint.tx += 4;
+	backupcornerpoint.rx += 4;
+	ret = cqspi_phy_apply_setting(f_pdata, &backupcornerpoint);
+	if (!ret)
+		ret = cqspi_phy_check_pattern(f_pdata, mem);
+
+	if (ret) {
+		backupcornerpoint.read_delay--;
+		ret = cqspi_phy_apply_setting(f_pdata, &backupcornerpoint);
+		if (!ret)
+			ret = cqspi_phy_check_pattern(f_pdata, mem);
+	}
+
+	if (ret)
+		goto out;
+
+	bottomleft.read_delay = backupcornerpoint.read_delay;
+
+	topright.tx = txhigh.tx;
+	topright.rx = rxhigh.rx;
+	if (txhigh.read_delay >= rxhigh.read_delay)
+		topright.read_delay = txhigh.read_delay;
+	else
+		topright.read_delay = rxhigh.read_delay;
+
+	/* Verify topright: Test 4 taps inside, adjust read_delay if needed */
+	backupcornerpoint = topright;
+	backupcornerpoint.tx -= 4;
+	backupcornerpoint.rx -= 4;
+	ret = cqspi_phy_apply_setting(f_pdata, &backupcornerpoint);
+	if (!ret)
+		ret = cqspi_phy_check_pattern(f_pdata, mem);
+
+	if (ret) {
+		backupcornerpoint.read_delay++;
+		ret = cqspi_phy_apply_setting(f_pdata, &backupcornerpoint);
+		if (!ret)
+			ret = cqspi_phy_check_pattern(f_pdata, mem);
+	}
+
+	if (ret)
+		goto out;
+
+	topright.read_delay = backupcornerpoint.read_delay;
+
+	dev_dbg(dev, "topright: RX: %d TX: %d RD: %d\n", topright.rx,
+		topright.tx, topright.read_delay);
+	dev_dbg(dev, "bottomleft: RX: %d TX: %d RD: %d\n", bottomleft.rx,
+		bottomleft.tx, bottomleft.read_delay);
+	cqspi_phy_find_gaplow_ddr(f_pdata, mem, &bottomleft, &topright, &gaplow);
+	dev_dbg(dev, "gaplow: RX: %d TX: %d RD: %d\n", gaplow.rx, gaplow.tx,
+		gaplow.read_delay);
+
+	/* Final point selection: Handle single vs dual passing regions */
+
+	if (bottomleft.read_delay == topright.read_delay) {
+		/*
+		 * Single region: Use midpoint with temperature compensation.
+		 * Gaplow approximates upper boundary of valid region.
+		 *
+		 *              rx
+		 *          127 ^
+		 *              |              gaplow (approx. topright)
+		 *              |              |
+		 *    rxhigh -----------xxxxxxx|          failing
+		 *              |       xxxxxxx|           region
+		 *              |       xxxxxxx|     <--------------->
+		 *              |       xxxxxxx|     +++++++++++++++++
+		 *              |       xxxxxxxxx     ++++++++++++++++
+		 *              |       xxxxxxxxxx     +++++++++++++++
+		 *              |       xxxxxxxxxxx     ++++++++++++++
+		 *              |       xxxxxxxxxxxx     +++++++++++++
+		 *              |       xxxxxxxxxxxxx     ++++++++++++
+		 *              |       xxxxxxxxxxxxxx     +++++++++++
+		 *              |       xxxxxxxxxxxxxxx     ++++++++++
+		 *              |       xxxxxxxxxxxxxxxx     +++++++++
+		 *              |       xxxxxxxxxxxxxxxxx     ++++++++
+		 *     rxlow -----------xxxxxxxxxxxxxxxxxx     +++++++
+		 *              |       *                            |
+		 *              | bottom|left                        |
+		 *              --------|----------------------------|---> tx
+		 *              0       |                            | 127
+		 *                      |                            |
+		 *                      txlow                   txhigh
+		 *                             (same read_delay)
+		 *
+		 * Temperature compensation: Valid region shifts with temp.
+		 * Offset = region_size / (330 / (temp - 42°C))
+		 * Factor 330 is empirically determined for this hardware.
+		 */
+
+		dev_dbg(dev,
+			"bottomleft and topright at the same read delay.\n");
+
+		topright = gaplow;
+		searchpoint.read_delay = bottomleft.read_delay;
+		searchpoint.tx =
+			bottomleft.tx + ((topright.tx - bottomleft.tx) / 2);
+		searchpoint.rx =
+			bottomleft.rx + ((topright.rx - bottomleft.rx) / 2);
+
+		ret = cqspi_get_temp(&temp);
+		if (ret) {
+			/* Assume room temperature if sensor unavailable */
+			dev_dbg(dev,
+				"Unable to get temperature. Assuming room temperature\n");
+			temp = CQSPI_PHY_DEFAULT_TEMP;
+		}
+
+		if (temp < CQSPI_PHY_MIN_TEMP || temp > CQSPI_PHY_MAX_TEMP) {
+			dev_err(dev,
+				"Temperature outside operating range: %dC\n",
+				temp);
+			ret = -EINVAL;
+			goto out;
+		}
+
+		if (temp == CQSPI_PHY_MID_TEMP)
+			temp++; /* Avoid divide-by-zero */
+		dev_dbg(dev, "Temperature: %dC\n", temp);
+
+		/*
+		 * Apply temperature offset: positive at high temp, negative at low.
+		 * Compute the divisor once and apply to both TX and RX. Use int
+		 * arithmetic throughout to avoid u8 wrapping on negative offsets.
+		 */
+		temp = 330 / (temp - CQSPI_PHY_MID_TEMP);
+		searchpoint.tx = clamp((int)searchpoint.tx +
+				       (topright.tx - bottomleft.tx) / temp,
+				       0, CQSPI_PHY_MAX_DELAY);
+		searchpoint.rx = clamp((int)searchpoint.rx +
+				       (topright.rx - bottomleft.rx) / temp,
+				       0, CQSPI_PHY_MAX_DELAY);
+	} else {
+		/*
+		 * Dual regions: Gap separates two valid regions, choose larger.
+		 *
+		 *              rx
+		 *          127 ^
+		 *              |                                 topright
+		 *              |                                    *
+		 *    rxhigh -----------xxxxx     +++++++++++++++++++|
+		 *              |       xxxxxx    <region 2> ++++++++|
+		 *              |       xxxxxxx     +++++++++++++++++|
+		 *              |       xxxxxxxx     ++++++++++++++++|
+		 *              |       xxxxxxxxx     +++++++++++++++|
+		 *              |       xxxxxxxxxx     ++++++++++++++|
+		 *              |                  failing           |
+		 *              |                  region            |
+		 *              |       xxxxxxxxxxxxx     +++++++++++|
+		 *              |       xxxxxxxxxxxxxx     ++++++++++|
+		 *              |       xxxxxxxxxxxxxxx     +++++++++|
+		 *              |       xxxxxxxxxxxxxxxx     ++++++++|
+		 *              |       xxxxxxxxx <region 1>  +++++++|
+		 *     rxlow -----------xxxxxxxxxxxxxxxxxx     ++++++|
+		 *              |       *                            |
+		 *              | bottom|left                        |
+		 *              --------|----------------------------|---> tx
+		 *              0       |                            | 127
+		 *                      |                            |
+		 *                      txlow                   txhigh
+		 *
+		 * Strategy: Compare Manhattan distances from gap boundaries to
+		 * corners. Choose corner furthest from gap (larger region).
+		 * Apply 16-tap margin inward, scale RX proportionally.
+		 */
+
+		cqspi_phy_find_gaphigh_ddr(f_pdata, mem, &bottomleft,
+					   &topright, &gaphigh);
+		dev_dbg(dev, "gaphigh: RX: %d TX: %d RD: %d\n", gaphigh.rx,
+			gaphigh.tx, gaphigh.read_delay);
+
+		if (topright.tx == bottomleft.tx) {
+			dev_err(dev, "zero TX span in dual-region: cannot compute search point\n");
+			ret = -EINVAL;
+			goto out;
+		}
+
+		/* Compare Manhattan distances: choose corner furthest from gap */
+		if ((abs(gaplow.tx - bottomleft.tx) +
+		     abs(gaplow.rx - bottomleft.rx)) <
+		    (abs(gaphigh.tx - topright.tx) +
+		     abs(gaphigh.rx - topright.rx))) {
+			/* Topright further: Use Region 2, 16 taps inward */
+			searchpoint = topright;
+			searchpoint.tx -= 16;
+			searchpoint.rx -= (16 * (topright.rx - bottomleft.rx)) /
+					  (topright.tx - bottomleft.tx);
+		} else {
+			/* Bottomleft further: Use Region 1, 16 taps inward */
+			searchpoint = bottomleft;
+			searchpoint.tx += 16;
+			searchpoint.rx += (16 * (topright.rx - bottomleft.rx)) /
+					  (topright.tx - bottomleft.tx);
+		}
+	}
+
+	/* Apply and verify final tuning point */
+	dev_dbg(dev, "Final tuning point: RX: %d TX: %d RD: %d\n",
+		searchpoint.rx, searchpoint.tx, searchpoint.read_delay);
+	ret = cqspi_phy_apply_setting(f_pdata, &searchpoint);
+	if (!ret)
+		ret = cqspi_phy_check_pattern(f_pdata, mem);
+
+	if (ret) {
+		dev_err(dev,
+			"Failed to find pattern at final calibration point\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	f_pdata->phy_setting.read_delay = searchpoint.read_delay;
+	f_pdata->phy_setting.rx = searchpoint.rx;
+	f_pdata->phy_setting.tx = searchpoint.tx;
+out:
+	if (ret)
+		f_pdata->use_tuned_phy = false;
+
+	return ret;
+}
+
+static int cqspi_phy_tuning_sdr(struct cqspi_flash_pdata *f_pdata,
+				struct spi_mem *mem)
+{
+	struct cqspi_st *cqspi = f_pdata->cqspi;
+	struct device *dev = &cqspi->pdev->dev;
+	struct phy_setting rxlow, rxhigh, first, second, final;
+	u8 window1 = 0;
+	u8 window2 = 0;
+	int ret;
+
+	/*
+	 * SDR tuning: 1D search for optimal RX delay (TX less critical).
+	 * Find two consecutive windows, choose larger, use midpoint.
+	 *
+	 *              rx
+	 *          127 ^
+	 *              |        |-----window at----------|
+	 *              |        |-----read_delay = n+1---|
+	 *              |        |xxxxxxxxxxxxxxxxxxxxxxxx|
+	 *              |        |xxxxxxxxxxxxxxxxxxxxxxxx|
+	 *              |        |xxxxxxxxxxxxxxxxxxxxxxxx|
+	 *              |        |xxxxxxxxxxxxxxxxxxxxxxxx|
+	 *              |        |xxxxxxxxxxxxxxxxxxxxxxxx|
+	 *              |        rxlow(n+1)   midpoint    rxhigh(n+1)
+	 *              |
+	 *              |   |---window at--------|
+	 *              |   |---read_delay = n---|
+	 *              |   |xxxxxxxxxxxxxxxxxxxx|
+	 *              |   |xxxxxxxxxxxxxxxxxxxx|
+	 *              |   |xxxxxxxxxxxxxxxxxxxx|
+	 *              |   |xxxxxxxxxxxxxxxxxxxx|
+	 *              |   |xxxxxxxxxxxxxxxxxxxx|
+	 *              |   rxlow(n)   midpoint  rxhigh(n)
+	 *              |
+	 *              -----------------------------------------> tx
+	 *              0                                      127
+	 *                  read_delay=n                  read_delay=n+1
+	 */
+
+	f_pdata->use_tuned_phy = true;
+	cqspi_phy_reset_setting(&rxlow);
+	cqspi_phy_reset_setting(&rxhigh);
+	cqspi_phy_reset_setting(&first);
+
+	/* First window: Find rxlow by incrementing read_delay from 0 */
+
+	/*
+	 *              rx
+	 *          127 ^
+	 *              |   |xxxxxxxxxxxxxxxxxxxx|
+	 *  search      |   |xxxxxxxxxxxxxxxxxxxx|
+	 *  rxlow       |   |xxxxxxxxxxxxxxxxxxxx|
+	 *  increasing  |   |xxxxxxxxxxxxxxxxxxxx|
+	 *           --------->|xxxxxxxxxxxxxxxxxxxx|
+	 *  read_delay  |        |xxxxxxxxxxxxxxxxxxx|
+	 *  until found |        |xxxxxxxxxxxxxxxxxxx|
+	 *              |        rxlow
+	 *              -----------------------------------------> tx
+	 *              0                            tx fixed at 127
+	 */
+
+	do {
+		ret = cqspi_find_rx_low_sdr(f_pdata, mem, &rxlow);
+
+		if (ret)
+			rxlow.read_delay++;
+	} while (ret && rxlow.read_delay <= CQSPI_PHY_MAX_RD);
+
+	/* Find rxhigh: Decrement from RX=127 at same read_delay */
+
+	/*
+	 *              rx
+	 *          127 ^        search rxhigh
+	 *              |        (decrement from
+	 *              |        127 until found)
+	 *              |          |
+	 *              |          |
+	 *              |          v
+	 *              |        |------------------------|
+	 *              |        |xxxxxxxxxxxxxxxxxxxxxxxx|
+	 *              |        |xxxxxxxxxxxxxxxxxxxxxxxx|
+	 *              |        |xxxxxxxxxxxxxxxxxxxxxxxx|
+	 *              |        |xxxxxxxxxxxxxxxxxxxxxxxx|
+	 *              |        |xxxxxxxxxxxxxxxxxxxxxxxx|
+	 *              |        rxlow                    rxhigh
+	 *              -----------------------------------------> tx
+	 *              0                            tx fixed at 127
+	 */
+
+	rxhigh.read_delay = rxlow.read_delay;
+	ret = cqspi_find_rx_high_sdr(f_pdata, mem, &rxhigh, rxlow.rx);
+	if (ret)
+		goto out;
+
+	/* Calculate first window midpoint for max margin */
+
+	/*
+	 *              rx
+	 *          127 ^
+	 *              |        |--------window1---------|
+	 *              |        |xxxxxxxxxxxxxxxxxxxxxxxx|
+	 *              |        |xxxxxxxxxxxxxxxxxxxxxxxx|
+	 *              |        |xxxxxxxxxxx * xxxxxxxxxx|
+	 *              |        |xxxxxxxxxxxxxxxxxxxxxxxx|
+	 *              |        |xxxxxxxxxxxxxxxxxxxxxxxx|
+	 *              |        rxlow        ^           rxhigh
+	 *              ----------------------|------------------> tx
+	 *              0                     |      tx fixed at 127
+	 *                            window1/2
+	 */
+
+	first.read_delay = rxlow.read_delay;
+	window1 = rxhigh.rx - rxlow.rx;
+	first.rx = rxlow.rx + (window1 / 2);
+
+	dev_dbg(dev, "First tuning point: RX: %d TX: %d RD: %d\n", first.rx,
+		first.tx, first.read_delay);
+	ret = cqspi_phy_apply_setting(f_pdata, &first);
+	if (!ret)
+		ret = cqspi_phy_check_pattern(f_pdata, mem);
+
+	if (ret || first.read_delay > CQSPI_PHY_MAX_RD)
+		goto out;
+
+	/* Second window: Search at read_delay+1, may differ in size */
+
+	/*
+	 *              rx
+	 *          127 ^
+	 *              |        |-------|
+	 *              |        |xxxxxxx|
+	 *              |        |xxxxxxx|
+	 *              |        |xxxxxxx|
+	 *              |        |xxxxxxx|
+	 *              |        |xxxxxxx|
+	 *              |        rxlow   rxhigh
+	 *              -----------------------------------------> tx
+	 *              0
+	 *              read_delay = n (smaller window)
+	 *
+	 *              rx
+	 *          127 ^
+	 *              |        |-----------------|
+	 *              |        |xxxxxxxxxxxxxxxxx|
+	 *              |        |xxxxxxxxxxxxxxxxx|
+	 *              |        |xxxxxxxxxxxxxxxxx|
+	 *              |        |xxxxxxxxxxxxxxxxx|
+	 *              |        |xxxxxxxxxxxxxxxxx|
+	 *              |        rxlow             rxhigh
+	 *              -----------------------------------------> tx
+	 *              0
+	 *              read_delay = n+1 (larger window - better)
+	 */
+
+	cqspi_phy_reset_setting(&rxlow);
+	cqspi_phy_reset_setting(&rxhigh);
+	cqspi_phy_reset_setting(&second);
+
+	rxlow.read_delay = first.read_delay + 1;
+	if (rxlow.read_delay > CQSPI_PHY_MAX_RD)
+		goto compare;
+
+	ret = cqspi_find_rx_low_sdr(f_pdata, mem, &rxlow);
+	if (ret)
+		goto compare;
+
+	rxhigh.read_delay = rxlow.read_delay;
+	ret = cqspi_find_rx_high_sdr(f_pdata, mem, &rxhigh, rxlow.rx);
+	if (ret)
+		goto compare;
+
+	/* Calculate second window midpoint */
+
+	/*
+	 *              rx
+	 *          127 ^
+	 *              |        |--------window2---------|
+	 *              |        |xxxxxxxxxxxxxxxxxxxxxxxx|
+	 *              |        |xxxxxxxxxxxxxxxxxxxxxxxx|
+	 *              |        |xxxxxxxxxxx * xxxxxxxxxx|
+	 *              |        |xxxxxxxxxxxxxxxxxxxxxxxx|
+	 *              |        |xxxxxxxxxxxxxxxxxxxxxxxx|
+	 *              |        rxlow        ^           rxhigh
+	 *              ----------------------|------------------> tx
+	 *              0                     |      tx fixed at 127
+	 *                            window2/2
+	 *              read_delay = n+1
+	 */
+
+	window2 = rxhigh.rx - rxlow.rx;
+	second.rx = rxlow.rx + (window2 / 2);
+	second.read_delay = rxlow.read_delay;
+
+	dev_dbg(dev, "Second tuning point: RX: %d TX: %d RD: %d\n", second.rx,
+		second.tx, second.read_delay);
+	ret = cqspi_phy_apply_setting(f_pdata, &second);
+	if (!ret)
+		ret = cqspi_phy_check_pattern(f_pdata, mem);
+
+	if (ret || second.read_delay > CQSPI_PHY_MAX_RD)
+		window2 = 0;
+
+	/* Window comparison: Choose larger window for better margin */
+
+compare:
+	cqspi_phy_reset_setting(&final);
+	if (window2 > window1) {
+		final.rx = second.rx;
+		final.read_delay = second.read_delay;
+	} else {
+		final.rx = first.rx;
+		final.read_delay = first.read_delay;
+	}
+
+	/* Apply and verify final tuning point */
+
+	dev_dbg(dev, "Final tuning point: RX: %d TX: %d RD: %d\n", final.rx,
+		final.tx, final.read_delay);
+	ret = cqspi_phy_apply_setting(f_pdata, &final);
+	if (!ret)
+		ret = cqspi_phy_check_pattern(f_pdata, mem);
+
+	if (ret) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	f_pdata->phy_setting.read_delay = final.read_delay;
+	f_pdata->phy_setting.rx = final.rx;
+	f_pdata->phy_setting.tx = final.tx;
+
+out:
+	if (ret)
+		f_pdata->use_tuned_phy = false;
+
+	return ret;
+}
+
+static int cqspi_am654_ospi_execute_tuning(struct spi_mem *mem,
+					   struct spi_mem_op *read_op,
+					   struct spi_mem_op *write_op)
+{
+	struct cqspi_st *cqspi =
+		spi_controller_get_devdata(mem->spi->controller);
+	struct cqspi_flash_pdata *f_pdata;
+	struct device *dev = &cqspi->pdev->dev;
+	u32 phy_offset = 0;
+	int ret;
+
+	f_pdata = &cqspi->f_pdata[spi_get_chipselect(mem->spi, 0)];
+
+	/*
+	 * spi-max-post-config-frequency must be present for PHY tuning.
+	 * If absent, post_config_max_speed_hz is zero and there is no
+	 * calibration target, so skip tuning gracefully.
+	 */
+	if (!mem->spi->post_config_max_speed_hz) {
+		dev_dbg(dev,
+			"No post-config frequency configured, skipping tuning\n");
+		return -EOPNOTSUPP;
+	}
+
+	if (write_op) {
+		/*
+		 * For NAND: write the calibration pattern to the page cache.
+		 * The write op runs at the conservative base speed (spi->max_speed_hz)
+		 * so the write itself is reliable before PHY calibration.
+		 */
+		ret = cqspi_write_pattern_to_cache(f_pdata, mem, write_op);
+		if (ret) {
+			dev_warn(dev,
+				 "failed to write pattern to cache: %d, skipping tuning\n",
+				 ret);
+			goto out;
+		}
+
+		f_pdata->phy_write_op = *write_op;
+	} else {
+		ret = cqspi_get_phy_pattern_offset(dev, &phy_offset);
+		if (ret) {
+			dev_warn(dev,
+				 "pattern partition not found: %d, skipping tuning\n",
+				 ret);
+			goto out;
+		}
+
+		read_op->addr.val = phy_offset;
+	}
+
+	/*
+	 * Verify the calibration pattern exists using the conservative base
+	 * speed.  At high clock rates the DLL is not yet trained, so DTR
+	 * data capture is unreliable and the read would return garbage.
+	 * Setting max_freq to 0 causes spi_mem_adjust_op_freq() to cap the
+	 * read to max_speed_hz (the base rate), well within reliable DTR
+	 * margins.  max_freq is set to post_config_max_speed_hz below after
+	 * the pattern is confirmed, so the tuning-loop reads run at full rate.
+	 */
+	f_pdata->phy_read_op = *read_op;
+	f_pdata->phy_read_op.max_freq = 0;
+
+	ret = cqspi_phy_check_pattern(f_pdata, mem);
+	if (ret) {
+		dev_err(dev, "pattern not found: %d, skipping tuning\n", ret);
+		goto out;
+	}
+
+	/*
+	 * Pattern confirmed.  Set phy_read_op.max_freq to
+	 * post_config_max_speed_hz so that tuning-loop reads bypass the base
+	 * frequency cap in spi_mem_adjust_op_freq() and run at the full
+	 * calibration rate.
+	 */
+	f_pdata->phy_read_op.max_freq = mem->spi->post_config_max_speed_hz;
+
+	if (read_op->cmd.dtr || read_op->addr.dtr || read_op->dummy.dtr ||
+	    read_op->data.dtr) {
+		f_pdata->use_dqs = true;
+		cqspi_phy_pre_config(cqspi, f_pdata, false);
+		ret = cqspi_phy_tuning_ddr(f_pdata, mem);
+	} else {
+		f_pdata->use_dqs = false;
+		cqspi_phy_pre_config(cqspi, f_pdata, true);
+		ret = cqspi_phy_tuning_sdr(f_pdata, mem);
+	}
+
+	if (ret)
+		dev_warn(dev, "tuning failed: %d\n", ret);
+
+	cqspi_phy_post_config(cqspi, f_pdata->read_delay);
+
+out:
+	/*
+	 * On success, write back the validated maximum speed into the caller's
+	 * op templates so that those specific ops bypass the cap in subsequent
+	 * exec_op calls.
+	 */
+	if (!ret) {
+		read_op->max_freq = mem->spi->post_config_max_speed_hz;
+		if (write_op)
+			write_op->max_freq = mem->spi->post_config_max_speed_hz;
+	}
+
+	return ret;
+}
+
+static int cqspi_mem_op_execute_tuning(struct spi_mem *mem,
+				       struct spi_mem_op *read_op,
+				       struct spi_mem_op *write_op)
+{
+	struct cqspi_st *cqspi =
+		spi_controller_get_devdata(mem->spi->controller);
+
+	if (!cqspi->ddata->execute_tuning)
+		return -EOPNOTSUPP;
+
+	return cqspi->ddata->execute_tuning(mem, read_op, write_op);
+}
+
 static int cqspi_of_get_flash_pdata(struct platform_device *pdev,
 				    struct cqspi_flash_pdata *f_pdata,
 				    struct device_node *np)
@@ -1584,11 +3337,6 @@ static int cqspi_of_get_flash_pdata(struct platform_device *pdev,
 		return -ENXIO;
 	}
 
-	if (of_property_read_u32(np, "spi-max-frequency", &f_pdata->clk_rate)) {
-		dev_err(&pdev->dev, "couldn't determine spi-max-frequency\n");
-		return -ENXIO;
-	}
-
 	return 0;
 }
 
@@ -1736,6 +3484,7 @@ static const struct spi_controller_mem_ops cqspi_mem_ops = {
 	.exec_op = cqspi_exec_mem_op,
 	.get_name = cqspi_get_name,
 	.supports_op = cqspi_supports_mem_op,
+	.execute_tuning = cqspi_mem_op_execute_tuning,
 };
 
 static const struct spi_controller_mem_caps cqspi_mem_caps = {
@@ -2104,6 +3853,7 @@ static const struct cqspi_driver_platdata k2g_qspi = {
 static const struct cqspi_driver_platdata am654_ospi = {
 	.hwcaps_mask = CQSPI_SUPPORTS_OCTAL | CQSPI_SUPPORTS_QUAD,
 	.quirks = CQSPI_NEEDS_WR_DELAY,
+	.execute_tuning = cqspi_am654_ospi_execute_tuning,
 };
 
 static const struct cqspi_driver_platdata intel_lgm_qspi = {
-- 
2.34.1