* [PATCH v5] dt-bindings: misc: convert lis302.txt to YAML
@ 2026-06-19 12:59 Jad Keskes
2026-06-19 13:08 ` sashiko-bot
0 siblings, 1 reply; 2+ messages in thread
From: Jad Keskes @ 2026-06-19 12:59 UTC (permalink / raw)
To: Eric Piel, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Jonathan Cameron, devicetree, linux-kernel, Jad Keskes
Replace the old lis302.txt with a YAML binding covering all four
compatibles (st,lis3lv02d, st,lis302dl-spi, st,lis331dlh,
st,lis33de) and their ~35 DT properties.
The old txt documented st,click-thresh-* and st,click-click-time-limit
but the code reads st,click-threshold-* and st,click-time-limit.
Keep the old names as deprecated so existing DTBs don't break.
Tested: dt_binding_check. dtbs_check against 7 omap/am335x DTBs
(am335x-evm, am335x-evmsk, am335x-pepper, am437x-sk-evm, omap3-n900,
omap3-n950, omap3-gta04a3) — no misc schema errors. Pre-existing
IIO schema errors on paired compatible nodes unchanged.
Signed-off-by: Jad Keskes <inasj268@gmail.com>
---
v5:
- Remove Vdd-supply/Vdd_IO-supply: false from SPI branch (hardware needs power regardless of bus)
- Split if/then into two branches: SPI requires spi-max-frequency + interrupts,
I2C requires Vdd-supply + Vdd_IO-supply (both optional on the other bus)
v4:
- Drop explicit select block (redundant)
- Fix commit message: select does not prevent IIO validation
v3:
- Add st,lis3lv02d to select block
- Drop Patch 2 entirely, single patch, no IIO changes
v2:
- Rebase onto Linux 7.1-rc6, drop IIO changes
.../devicetree/bindings/iio/accel/lis302.txt | 119 ------
.../bindings/misc/st,lis3lv02d.yaml | 400 ++++++++++++++++++
MAINTAINERS | 1 +
3 files changed, 401 insertions(+), 119 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/iio/accel/lis302.txt
create mode 100644 Documentation/devicetree/bindings/misc/st,lis3lv02d.yaml
diff --git a/Documentation/devicetree/bindings/iio/accel/lis302.txt b/Documentation/devicetree/bindings/iio/accel/lis302.txt
deleted file mode 100644
index 457539647f36..000000000000
--- a/Documentation/devicetree/bindings/iio/accel/lis302.txt
+++ /dev/null
@@ -1,119 +0,0 @@
-LIS302 accelerometer devicetree bindings
-
-This device is matched via its bus drivers, and has a number of properties
-that apply in on the generic device (independent from the bus).
-
-
-Required properties for the SPI bindings:
- - compatible: should be set to "st,lis3lv02d-spi"
- - reg: the chipselect index
- - spi-max-frequency: maximal bus speed, should be set to 1000000 unless
- constrained by external circuitry
- - interrupts: the interrupt generated by the device
-
-Required properties for the I2C bindings:
- - compatible: should be set to "st,lis3lv02d"
- - reg: i2c slave address
- - Vdd-supply: The input supply for Vdd
- - Vdd_IO-supply: The input supply for Vdd_IO
-
-
-Optional properties for all bus drivers:
-
- - st,click-single-{x,y,z}: if present, tells the device to issue an
- interrupt on single click events on the
- x/y/z axis.
- - st,click-double-{x,y,z}: if present, tells the device to issue an
- interrupt on double click events on the
- x/y/z axis.
- - st,click-thresh-{x,y,z}: set the x/y/z axis threshold
- - st,click-click-time-limit: click time limit, from 0 to 127.5msec
- with step of 0.5 msec
- - st,click-latency: click latency, from 0 to 255 msec with
- step of 1 msec.
- - st,click-window: click window, from 0 to 255 msec with
- step of 1 msec.
- - st,irq{1,2}-disable: disable IRQ 1/2
- - st,irq{1,2}-ff-wu-1: raise IRQ 1/2 on FF_WU_1 condition
- - st,irq{1,2}-ff-wu-2: raise IRQ 1/2 on FF_WU_2 condition
- - st,irq{1,2}-data-ready: raise IRQ 1/2 on data ready condition
- - st,irq{1,2}-click: raise IRQ 1/2 on click condition
- - st,irq-open-drain: consider IRQ lines open-drain
- - st,irq-active-low: make IRQ lines active low
- - st,wu-duration-1: duration register for Free-Fall/Wake-Up
- interrupt 1
- - st,wu-duration-2: duration register for Free-Fall/Wake-Up
- interrupt 2
- - st,wakeup-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for
- upper/lower limit
- - st,wakeup-threshold: set wakeup threshold
- - st,wakeup2-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for
- upper/lower limit for second wakeup
- engine.
- - st,wakeup2-threshold: set wakeup threshold for second wakeup
- engine.
- - st,highpass-cutoff-hz=: 1, 2, 4 or 8 for 1Hz, 2Hz, 4Hz or 8Hz of
- highpass cut-off frequency
- - st,hipass{1,2}-disable: disable highpass 1/2.
- - st,default-rate=: set the default rate
- - st,axis-{x,y,z}=: set the axis to map to the three coordinates.
- Negative values can be used for inverted axis.
- - st,{min,max}-limit-{x,y,z} set the min/max limits for x/y/z axis
- (used by self-test)
-
-
-Example for a SPI device node:
-
- accelerometer@0 {
- compatible = "st,lis302dl-spi";
- reg = <0>;
- spi-max-frequency = <1000000>;
- interrupt-parent = <&gpio>;
- interrupts = <104 0>;
-
- st,click-single-x;
- st,click-single-y;
- st,click-single-z;
- st,click-thresh-x = <10>;
- st,click-thresh-y = <10>;
- st,click-thresh-z = <10>;
- st,irq1-click;
- st,irq2-click;
- st,wakeup-x-lo;
- st,wakeup-x-hi;
- st,wakeup-y-lo;
- st,wakeup-y-hi;
- st,wakeup-z-lo;
- st,wakeup-z-hi;
- };
-
-Example for a I2C device node:
-
- lis331dlh: accelerometer@18 {
- compatible = "st,lis331dlh", "st,lis3lv02d";
- reg = <0x18>;
- Vdd-supply = <&lis3_reg>;
- Vdd_IO-supply = <&lis3_reg>;
-
- st,click-single-x;
- st,click-single-y;
- st,click-single-z;
- st,click-thresh-x = <10>;
- st,click-thresh-y = <10>;
- st,click-thresh-z = <10>;
- st,irq1-click;
- st,irq2-click;
- st,wakeup-x-lo;
- st,wakeup-x-hi;
- st,wakeup-y-lo;
- st,wakeup-y-hi;
- st,wakeup-z-lo;
- st,wakeup-z-hi;
- st,min-limit-x = <120>;
- st,min-limit-y = <120>;
- st,min-limit-z = <140>;
- st,max-limit-x = <550>;
- st,max-limit-y = <550>;
- st,max-limit-z = <750>;
- };
-
diff --git a/Documentation/devicetree/bindings/misc/st,lis3lv02d.yaml b/Documentation/devicetree/bindings/misc/st,lis3lv02d.yaml
new file mode 100644
index 000000000000..c73371b754a1
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/st,lis3lv02d.yaml
@@ -0,0 +1,400 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/misc/st,lis3lv02d.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics LIS3LV02D and similar accelerometers (misc driver)
+
+maintainers:
+ - Eric Piel <eric.piel@tremplin-utc.net>
+
+description:
+ This binding describes the STMicroelectronics accelerometers supported by
+ the misc/lis3lv02d driver. This driver provides input (joystick) and
+ hardware monitoring support, in contrast to the IIO st-accel driver which
+ also supports some of these devices.
+ Refer to Documentation/devicetree/bindings/iio/st,st-sensors.yaml for the
+ IIO binding.
+
+select:
+ anyOf:
+ - properties:
+ compatible:
+ contains:
+ const: st,lis302dl-spi
+ - properties:
+ compatible:
+ contains:
+ const: st,lis331dlh
+ - properties:
+ compatible:
+ contains:
+ const: st,lis33de
+ - properties:
+ compatible:
+ contains:
+ const: st,lis3lv02d
+ required:
+ - compatible
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - enum:
+ - st,lis331dlh
+ - st,lis33de
+ - const: st,lis3lv02d
+ - const: st,lis331dlh
+ - const: st,lis3lv02d
+ - const: st,lis302dl-spi
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ minItems: 1
+ maxItems: 2
+
+ spi-max-frequency:
+ description: SPI bus frequency; should be set to 1000000 unless
+ constrained by external circuitry.
+ maximum: 1000000
+
+ Vdd-supply:
+ description: The input supply for Vdd.
+
+ Vdd_IO-supply:
+ description: The input supply for Vdd_IO.
+
+ st,click-single-x:
+ description: Issue an interrupt on single click events on the X axis.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,click-double-x:
+ description: Issue an interrupt on double click events on the X axis.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,click-single-y:
+ description: Issue an interrupt on single click events on the Y axis.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,click-double-y:
+ description: Issue an interrupt on double click events on the Y axis.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,click-single-z:
+ description: Issue an interrupt on single click events on the Z axis.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,click-double-z:
+ description: Issue an interrupt on double click events on the Z axis.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,click-thresh-x:
+ description: X axis click threshold (deprecated spelling, use st,click-threshold-x).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ deprecated: true
+
+ st,click-thresh-y:
+ description: Y axis click threshold (deprecated spelling, use st,click-threshold-y).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ deprecated: true
+
+ st,click-thresh-z:
+ description: Z axis click threshold (deprecated spelling, use st,click-threshold-z).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ deprecated: true
+
+ st,click-threshold-x:
+ description: X axis click threshold.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ st,click-threshold-y:
+ description: Y axis click threshold.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ st,click-threshold-z:
+ description: Z axis click threshold.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ st,click-click-time-limit:
+ description: Click time limit (deprecated spelling, use st,click-time-limit).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+ deprecated: true
+
+ st,click-time-limit:
+ description: Click time limit, from 0 to 127.5 msec with step of 0.5 msec.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+
+ st,click-latency:
+ description: Click latency, from 0 to 255 msec with step of 1 msec.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+
+ st,click-window:
+ description: Click window, from 0 to 255 msec with step of 1 msec.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+
+ st,irq1-disable:
+ description: Disable IRQ 1.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq1-ff-wu-1:
+ description: Raise IRQ 1 on FF_WU_1 condition.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq1-ff-wu-2:
+ description: Raise IRQ 1 on FF_WU_2 condition.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq1-data-ready:
+ description: Raise IRQ 1 on data ready condition.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq1-click:
+ description: Raise IRQ 1 on click condition.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq2-disable:
+ description: Disable IRQ 2.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq2-ff-wu-1:
+ description: Raise IRQ 2 on FF_WU_1 condition.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq2-ff-wu-2:
+ description: Raise IRQ 2 on FF_WU_2 condition.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq2-data-ready:
+ description: Raise IRQ 2 on data ready condition.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq2-click:
+ description: Raise IRQ 2 on click condition.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq-open-drain:
+ description: Consider IRQ lines open-drain.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq-active-low:
+ description: Make IRQ lines active low.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wu-duration-1:
+ description: Duration register for Free-Fall/Wake-Up interrupt 1.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+
+ st,wu-duration-2:
+ description: Duration register for Free-Fall/Wake-Up interrupt 2.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+
+ st,wakeup-x-lo:
+ description: Set wakeup condition on X axis for lower limit.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup-x-hi:
+ description: Set wakeup condition on X axis for upper limit.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup-y-lo:
+ description: Set wakeup condition on Y axis for lower limit.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup-y-hi:
+ description: Set wakeup condition on Y axis for upper limit.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup-z-lo:
+ description: Set wakeup condition on Z axis for lower limit.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup-z-hi:
+ description: Set wakeup condition on Z axis for upper limit.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup-threshold:
+ description: Set wakeup threshold.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+
+ st,wakeup2-x-lo:
+ description: Set wakeup condition on X axis for lower limit for second wakeup engine.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup2-x-hi:
+ description: Set wakeup condition on X axis for upper limit for second wakeup engine.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup2-y-lo:
+ description: Set wakeup condition on Y axis for lower limit for second wakeup engine.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup2-y-hi:
+ description: Set wakeup condition on Y axis for upper limit for second wakeup engine.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup2-z-lo:
+ description: Set wakeup condition on Z axis for lower limit for second wakeup engine.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup2-z-hi:
+ description: Set wakeup condition on Z axis for upper limit for second wakeup engine.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup2-threshold:
+ description: Set wakeup threshold for second wakeup engine.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+
+ st,highpass-cutoff-hz:
+ description: Highpass cut-off frequency. Valid values are 1, 2, 4 or 8.
+ enum: [1, 2, 4, 8]
+
+ st,hipass1-disable:
+ description: Disable highpass filter 1.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,hipass2-disable:
+ description: Disable highpass filter 2.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,default-rate:
+ description: Set the default output data rate.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ st,axis-x:
+ description: Set the X axis mapping. Negative values can be used for inverted axis.
+ $ref: /schemas/types.yaml#/definitions/int32
+
+ st,axis-y:
+ description: Set the Y axis mapping. Negative values can be used for inverted axis.
+ $ref: /schemas/types.yaml#/definitions/int32
+
+ st,axis-z:
+ description: Set the Z axis mapping. Negative values can be used for inverted axis.
+ $ref: /schemas/types.yaml#/definitions/int32
+
+ st,min-limit-x:
+ description: Minimum limit for X axis (used by self-test).
+ $ref: /schemas/types.yaml#/definitions/int32
+
+ st,min-limit-y:
+ description: Minimum limit for Y axis (used by self-test).
+ $ref: /schemas/types.yaml#/definitions/int32
+
+ st,min-limit-z:
+ description: Minimum limit for Z axis (used by self-test).
+ $ref: /schemas/types.yaml#/definitions/int32
+
+ st,max-limit-x:
+ description: Maximum limit for X axis (used by self-test).
+ $ref: /schemas/types.yaml#/definitions/int32
+
+ st,max-limit-y:
+ description: Maximum limit for Y axis (used by self-test).
+ $ref: /schemas/types.yaml#/definitions/int32
+
+ st,max-limit-z:
+ description: Maximum limit for Z axis (used by self-test).
+ $ref: /schemas/types.yaml#/definitions/int32
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ not:
+ contains:
+ const: st,lis302dl-spi
+ then:
+ required:
+ - Vdd-supply
+ - Vdd_IO-supply
+ else:
+ properties:
+ Vdd-supply: false
+ Vdd_IO-supply: false
+ required:
+ - spi-max-frequency
+ - interrupts
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ accelerometer@18 {
+ compatible = "st,lis331dlh", "st,lis3lv02d";
+ reg = <0x18>;
+ Vdd-supply = <&lis3_reg>;
+ Vdd_IO-supply = <&lis3_reg>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <18 0>;
+
+ st,click-single-x;
+ st,click-single-y;
+ st,click-single-z;
+ st,click-threshold-x = <10>;
+ st,click-threshold-y = <10>;
+ st,click-threshold-z = <10>;
+ st,irq1-click;
+ st,irq2-click;
+ st,wakeup-x-lo;
+ st,wakeup-x-hi;
+ st,wakeup-y-lo;
+ st,wakeup-y-hi;
+ st,wakeup-z-lo;
+ st,wakeup-z-hi;
+ st,min-limit-x = <120>;
+ st,min-limit-y = <120>;
+ st,min-limit-z = <140>;
+ st,max-limit-x = <550>;
+ st,max-limit-y = <550>;
+ st,max-limit-z = <750>;
+ };
+ };
+ - |
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ accelerometer@0 {
+ compatible = "st,lis302dl-spi";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ interrupt-parent = <&gpio>;
+ interrupts = <104 0>;
+
+ st,click-single-x;
+ st,click-single-y;
+ st,click-single-z;
+ st,click-threshold-x = <10>;
+ st,click-threshold-y = <10>;
+ st,click-threshold-z = <10>;
+ st,irq1-click;
+ st,irq2-click;
+ st,wakeup-x-lo;
+ st,wakeup-x-hi;
+ st,wakeup-y-lo;
+ st,wakeup-y-hi;
+ st,wakeup-z-lo;
+ st,wakeup-z-hi;
+ };
+ };
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 9ec290e38b44..4cffabbabf0e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14858,6 +14858,7 @@ T: git git://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/
LIS3LV02D ACCELEROMETER DRIVER
M: Eric Piel <eric.piel@tremplin-utc.net>
S: Maintained
+F: Documentation/devicetree/bindings/misc/st,lis3lv02d.yaml
F: Documentation/misc-devices/lis3lv02d.rst
F: drivers/misc/lis3lv02d/
F: drivers/platform/x86/hp/hp_accel.c
--
2.54.0
^ permalink raw reply related [flat|nested] 2+ messages in thread
* Re: [PATCH v5] dt-bindings: misc: convert lis302.txt to YAML
2026-06-19 12:59 [PATCH v5] dt-bindings: misc: convert lis302.txt to YAML Jad Keskes
@ 2026-06-19 13:08 ` sashiko-bot
0 siblings, 0 replies; 2+ messages in thread
From: sashiko-bot @ 2026-06-19 13:08 UTC (permalink / raw)
To: Jad Keskes; +Cc: conor+dt, robh, devicetree
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Medium] The YAML schema incorrectly forbids the `Vdd-supply` and `Vdd_IO-supply` properties for the SPI variant and contains a redundant `select` block.
--
commit 124e32c58b0e195eb97adbc2880712f6df5eb1b2
Author: Jad Keskes <inasj268@gmail.com>
dt-bindings: misc: convert lis302.txt to YAML
This commit converts the old lis302.txt dt-binding to YAML format,
supporting the st,lis3lv02d, st,lis302dl-spi, st,lis331dlh, and
st,lis33de compatibles. It retains old property names as deprecated
to maintain backward compatibility with existing device trees.
> diff --git a/Documentation/devicetree/bindings/misc/st,lis3lv02d.yaml b/Documentation/devicetree/bindings/misc/st,lis3lv02d.yaml
> new file mode 100644
> index 0000000000000..c73371b754a1e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/misc/st,lis3lv02d.yaml
[ ... ]
> +description:
> + This binding describes the STMicroelectronics accelerometers supported by
> + the misc/lis3lv02d driver. This driver provides input (joystick) and
> + hardware monitoring support, in contrast to the IIO st-accel driver which
> + also supports some of these devices.
> + Refer to Documentation/devicetree/bindings/iio/st,st-sensors.yaml for the
> + IIO binding.
> +
> +select:
> + anyOf:
> + - properties:
> + compatible:
> + contains:
> + const: st,lis302dl-spi
> + - properties:
> + compatible:
> + contains:
> + const: st,lis331dlh
> + - properties:
> + compatible:
> + contains:
> + const: st,lis33de
> + - properties:
> + compatible:
> + contains:
> + const: st,lis3lv02d
> + required:
> + - compatible
> +
> +properties:
[Severity: Medium]
Is this explicit select block necessary? The dt-schema tooling
automatically selects bindings based on the top-level compatible
property definition, making this manual select block redundant.
[ ... ]
> +allOf:
> + - if:
> + properties:
> + compatible:
> + not:
> + contains:
> + const: st,lis302dl-spi
> + then:
> + required:
> + - Vdd-supply
> + - Vdd_IO-supply
> + else:
> + properties:
> + Vdd-supply: false
> + Vdd_IO-supply: false
[Severity: Medium]
Does setting these properties to false incorrectly enforce a hardware
abstraction violation? The physical chip requires power to operate
regardless of whether it uses the SPI bus or I2C. Device tree bindings
should describe the hardware, not the current limitations of the driver code.
> + required:
> + - spi-max-frequency
> + - interrupts
> +
> +required:
--
Sashiko AI review · https://sashiko.dev/#/patchset/20260619125902.893742-1-inasj268@gmail.com?part=1
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2026-06-19 13:08 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-06-19 12:59 [PATCH v5] dt-bindings: misc: convert lis302.txt to YAML Jad Keskes
2026-06-19 13:08 ` sashiko-bot
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox