[PATCH v5 0/4] clk: sun6i-rtc: Add support for Allwinner A733 SoC

[PATCH v5 0/4] clk: sun6i-rtc: Add support for Allwinner A733 SoC

[Jerome Brunet]

Add support for the Allwinner A733 RTC and its internal Clock Control
Unit (CCU). Reuse the rtc-sun6i rtc driver while introducing a new
SoC-specific RTC CCU driver to handle the hardware's evolved clock
structure.

The A733 implementation supports hardware detection of three external
crystal frequencies (19.2MHz, 24MHz and 26MHz), which is represented in
the driver via read-only divider operations. Implement logic to derive a
normalized 32kHz reference from these DCXO sources using fixed
pre-dividers. Additionally, provide several new DCXO gate clocks for
peripherals, including SerDes, HDMI, and UFS.

This was tested on a Raxda Cubie A7A.

Changes in v5:
- Droped already applied changes
- Fix determine rate mux helper calculation
- Changed clock split commit description
- Added a macro for the clock number without gates
- Link to v4: https://patch.msgid.link/20260706-a733-rtc-v4-0-f330728db3d3@baylibre.com

Changes in v4:
- Remove unneeded export of mux prediv helpers
- Link to v3: https://patch.msgid.link/20260702-a733-rtc-v3-0-eb2580374de6@baylibre.com

Changes in v3:
- Disallow clock-output-names DT property for h616/r329 chips
- Fix ccu probe helper to properly unregister clocks on error
- Implement .determine_rate for ccu divider RO ops
- Drop unused DCXO_CTRL_REG_EN define
- Link to v2: https://patch.msgid.link/20260629-a733-rtc-v2-0-7b72112784f8@baylibre.com

Changes in v2:
* Changed DT bindings as suggested. Those have changed significantly
  since v1 so I did not pick up Rob's review trailer
* Support added in the existing RTC CCU driver rather than a separate driver
* Added DT parsing clean up of the existing driver
* Xtal detection exposed by RO divider rather than a MUX.
* Dropped conversion to aux device for now. This is not strictly related
  the a733 support and will submitted again later on.
* Link to v1: https://lore.kernel.org/r/20260121-a733-rtc-v1-0-d359437f23a7@pigmoral.tech

---
Jerome Brunet (4):
      clk: sunxi-ng: mux: fix determine helper rate propagation
      clk: sunxi-ng: div: add read-only operation support
      clk: sunxi-ng: sun6i-rtc: split main oscillator div and gate.
      clk: sunxi-ng: sun6i-rtc: add a733 support

 drivers/clk/sunxi-ng/ccu-sun6i-rtc.c | 89 ++++++++++++++++++++++++++++++++----
 drivers/clk/sunxi-ng/ccu-sun6i-rtc.h |  3 +-
 drivers/clk/sunxi-ng/ccu_div.c       | 30 +++++++++++-
 drivers/clk/sunxi-ng/ccu_div.h       |  1 +
 drivers/clk/sunxi-ng/ccu_mux.c       | 58 ++++++++++++-----------
 drivers/clk/sunxi-ng/ccu_mux.h       |  4 ++
 6 files changed, 144 insertions(+), 41 deletions(-)
---
base-commit: c52b5090bf1e3b88745f8a81f264f34100ecde42
change-id: 20251226-a733-rtc-c5167df14e6e

Best regards,
--  
Jerome

[PATCH v5 1/4] clk: sunxi-ng: mux: fix determine helper rate propagation

[Jerome Brunet]

Applying the pre divider on the parent rate is wrong because, while
handling rate propagation through determine_rate(), the framework will
likely round the parent rate again while cycling through the possibilities,
throwing away the prediv applied. This means, the parent rate will then
be wrong when the prediv is unapplied from a parent rate on which it
was never applied to begin with.

The right way to do it is to unapply the prediv from the requested rate,
which is the wanted rate at the input on the clock element, and pass this
to framework to do its thing.

Change the determine rate mux helper in this way.

Fixes: 1c8d7af61b37 ("clk: sunxi-ng: convert from divider_round_rate_parent() to divider_determine_rate()")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
 drivers/clk/sunxi-ng/ccu_mux.c | 56 ++++++++++++++++++++----------------------
 1 file changed, 27 insertions(+), 29 deletions(-)

diff --git a/drivers/clk/sunxi-ng/ccu_mux.c b/drivers/clk/sunxi-ng/ccu_mux.c
index 09230728c400..75ec3457324c 100644
--- a/drivers/clk/sunxi-ng/ccu_mux.c
+++ b/drivers/clk/sunxi-ng/ccu_mux.c
@@ -92,66 +92,64 @@ int ccu_mux_helper_determine_rate(struct ccu_common *common,
 		struct clk_rate_request adj_req = *req;
 
 		best_parent = clk_hw_get_parent(hw);
-		best_parent_rate = clk_hw_get_rate(best_parent);
-
+		adj_req.best_parent_rate = clk_hw_get_rate(best_parent);
 		adj_req.best_parent_hw = best_parent;
-		adj_req.best_parent_rate = ccu_mux_helper_apply_prediv(common, cm, -1,
-								       best_parent_rate);
+
+		/*
+		 * This effectively treat the predivider as a postdivider.
+		 * It stays mathematically correct and ensure whatever
+		 * round() will do stays correct while walking the tree.
+		 * It may query the parent rate too while handling rate propagation
+		 */
+		adj_req.rate = ccu_mux_helper_unapply_prediv(common, cm, -1,
+							     req->rate);
 
 		ret = round(cm, &adj_req, data);
 		if (ret)
 			return ret;
 
-		best_rate = adj_req.rate;
-
 		/*
-		 * best_parent_rate might have been modified by our clock.
-		 * Unapply the pre-divider if there's one, and give
-		 * the actual frequency the parent needs to run at.
+		 * parent_rate might have been modified by our clock as part
+		 * of the rate propagation mechnanism. Same goes below.
 		 */
-		best_parent_rate = ccu_mux_helper_unapply_prediv(common, cm, -1,
-								 adj_req.best_parent_rate);
+		best_parent_rate = adj_req.best_parent_rate;
+		best_rate = ccu_mux_helper_apply_prediv(common, cm, -1,
+							adj_req.rate);
 
 		goto out;
 	}
 
 	for (i = 0; i < clk_hw_get_num_parents(hw); i++) {
 		struct clk_rate_request tmp_req = *req;
-		unsigned long parent_rate;
+		unsigned long rate;
 		struct clk_hw *parent;
 
 		parent = clk_hw_get_parent_by_index(hw, i);
 		if (!parent)
 			continue;
 
-		parent_rate = ccu_mux_helper_apply_prediv(common, cm, i,
-							  clk_hw_get_rate(parent));
-
 		tmp_req.best_parent_hw = parent;
-		tmp_req.best_parent_rate = parent_rate;
+		tmp_req.best_parent_rate = clk_hw_get_rate(parent);
+		tmp_req.rate = ccu_mux_helper_unapply_prediv(common, cm, i,
+							     req->rate);
 
 		ret = round(cm, &tmp_req, data);
 		if (ret)
 			continue;
 
-		/*
-		 * parent_rate might have been modified by our clock.
-		 * Unapply the pre-divider if there's one, and give
-		 * the actual frequency the parent needs to run at.
-		 */
-		parent_rate = ccu_mux_helper_unapply_prediv(common, cm, i,
-							    tmp_req.best_parent_rate);
+		rate = ccu_mux_helper_apply_prediv(common, cm, i,
+						   tmp_req.rate);
 
-		if (tmp_req.rate == req->rate) {
+		if (rate == req->rate) {
 			best_parent = parent;
-			best_parent_rate = parent_rate;
-			best_rate = tmp_req.rate;
+			best_parent_rate = tmp_req.best_parent_rate;
+			best_rate = rate;
 			goto out;
 		}
 
-		if (ccu_is_better_rate(common, req->rate, tmp_req.rate, best_rate)) {
-			best_rate = tmp_req.rate;
-			best_parent_rate = parent_rate;
+		if (ccu_is_better_rate(common, req->rate, rate, best_rate)) {
+			best_rate = rate;
+			best_parent_rate = tmp_req.best_parent_rate;
 			best_parent = parent;
 		}
 	}

-- 
2.47.3

Re: [PATCH v5 1/4] clk: sunxi-ng: mux: fix determine helper rate propagation

[sashiko-bot]

> Applying the pre divider on the parent rate is wrong because, while
> handling rate propagation through determine_rate(), the framework will
> likely round the parent rate again while cycling through the possibilities,
> throwing away the prediv applied. This means, the parent rate will then
> be wrong when the prediv is unapplied from a parent rate on which it
> was never applied to begin with.
> 
> The right way to do it is to unapply the prediv from the requested rate,
> which is the wanted rate at the input on the clock element, and pass this
> to framework to do its thing.
> 
> Change the determine rate mux helper in this way.
> 
> Fixes: 1c8d7af61b37 ("clk: sunxi-ng: convert from divider_round_rate_parent() to divider_determine_rate()")
> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

Sashiko has reviewed this patch and found no issues. It looks great!

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260717-a733-rtc-v5-0-3874cc26abf7@baylibre.com?part=1

[PATCH v5 2/4] clk: sunxi-ng: div: add read-only operation support

[Jerome Brunet]

Add support for sunxi-ng read-only dividers. This will be
useful to the a733 oscillator detection logic.

Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
 drivers/clk/sunxi-ng/ccu_div.c | 30 ++++++++++++++++++++++++++++--
 drivers/clk/sunxi-ng/ccu_div.h |  1 +
 drivers/clk/sunxi-ng/ccu_mux.c |  2 +-
 drivers/clk/sunxi-ng/ccu_mux.h |  4 ++++
 4 files changed, 34 insertions(+), 3 deletions(-)

diff --git a/drivers/clk/sunxi-ng/ccu_div.c b/drivers/clk/sunxi-ng/ccu_div.c
index 62d680ccb524..93cb4cb93abe 100644
--- a/drivers/clk/sunxi-ng/ccu_div.c
+++ b/drivers/clk/sunxi-ng/ccu_div.c
@@ -20,8 +20,22 @@ static int ccu_div_determine_rate_helper(struct ccu_mux_internal *mux,
 	if (cd->common.features & CCU_FEATURE_FIXED_POSTDIV)
 		req->rate *= cd->fixed_post_div;
 
-	ret = divider_determine_rate(&cd->common.hw, req, cd->div.table,
-				     cd->div.width, cd->div.flags);
+	if (cd->div.flags & CLK_DIVIDER_READ_ONLY) {
+		unsigned long val;
+		u32 reg;
+
+		reg = readl(cd->common.base + cd->common.reg);
+		val = reg >> cd->div.shift;
+		val &= (1 << cd->div.width) - 1;
+
+		ret = divider_ro_determine_rate(&cd->common.hw, req, cd->div.table,
+						cd->div.width, cd->div.flags, val);
+
+	} else {
+		ret = divider_determine_rate(&cd->common.hw, req, cd->div.table,
+					     cd->div.width, cd->div.flags);
+	}
+
 	if (ret)
 		return ret;
 
@@ -143,3 +157,15 @@ const struct clk_ops ccu_div_ops = {
 	.set_rate	= ccu_div_set_rate,
 };
 EXPORT_SYMBOL_NS_GPL(ccu_div_ops, "SUNXI_CCU");
+
+const struct clk_ops ccu_rodiv_ops = {
+	.disable	= ccu_div_disable,
+	.enable		= ccu_div_enable,
+	.is_enabled	= ccu_div_is_enabled,
+
+	.get_parent	= ccu_div_get_parent,
+
+	.determine_rate	= ccu_div_determine_rate,
+	.recalc_rate	= ccu_div_recalc_rate,
+};
+EXPORT_SYMBOL_NS_GPL(ccu_rodiv_ops, "SUNXI_CCU");
diff --git a/drivers/clk/sunxi-ng/ccu_div.h b/drivers/clk/sunxi-ng/ccu_div.h
index be00b3277e97..a30a92780a05 100644
--- a/drivers/clk/sunxi-ng/ccu_div.h
+++ b/drivers/clk/sunxi-ng/ccu_div.h
@@ -300,5 +300,6 @@ static inline struct ccu_div *hw_to_ccu_div(struct clk_hw *hw)
 }
 
 extern const struct clk_ops ccu_div_ops;
+extern const struct clk_ops ccu_rodiv_ops;
 
 #endif /* _CCU_DIV_H_ */
diff --git a/drivers/clk/sunxi-ng/ccu_mux.c b/drivers/clk/sunxi-ng/ccu_mux.c
index 75ec3457324c..905570375711 100644
--- a/drivers/clk/sunxi-ng/ccu_mux.c
+++ b/drivers/clk/sunxi-ng/ccu_mux.c
@@ -67,7 +67,7 @@ unsigned long ccu_mux_helper_apply_prediv(struct ccu_common *common,
 	return parent_rate / ccu_mux_get_prediv(common, cm, parent_index);
 }
 
-static unsigned long ccu_mux_helper_unapply_prediv(struct ccu_common *common,
+unsigned long ccu_mux_helper_unapply_prediv(struct ccu_common *common,
 					    struct ccu_mux_internal *cm,
 					    int parent_index,
 					    unsigned long parent_rate)
diff --git a/drivers/clk/sunxi-ng/ccu_mux.h b/drivers/clk/sunxi-ng/ccu_mux.h
index c94a4bde5d01..272a2c36a8f2 100644
--- a/drivers/clk/sunxi-ng/ccu_mux.h
+++ b/drivers/clk/sunxi-ng/ccu_mux.h
@@ -134,6 +134,10 @@ unsigned long ccu_mux_helper_apply_prediv(struct ccu_common *common,
 					  struct ccu_mux_internal *cm,
 					  int parent_index,
 					  unsigned long parent_rate);
+unsigned long ccu_mux_helper_unapply_prediv(struct ccu_common *common,
+					    struct ccu_mux_internal *cm,
+					    int parent_index,
+					    unsigned long parent_rate);
 int ccu_mux_helper_determine_rate(struct ccu_common *common,
 				  struct ccu_mux_internal *cm,
 				  struct clk_rate_request *req,

-- 
2.47.3

Re: [PATCH v5 2/4] clk: sunxi-ng: div: add read-only operation support

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 2 potential issue(s) to consider:

New issues:
- [High] Missing `.set_parent` in `ccu_rodiv_ops` leads to silent software-hardware clock tree desynchronization during reparenting.

Pre-existing issues:
- [High] Unvalidated hardware register read passed to `divider_ro_determine_rate()` can cause a divide-by-zero kernel panic.
--

--- Patch [2]: [PATCH v5 2/4] clk: sunxi-ng: div: add read-only operation support ---
commit d732b1bc291c593bb4873ef5f04edb2855137f30
Author: Jerome Brunet <jbrunet@baylibre.com>

clk: sunxi-ng: div: add read-only operation support

This commit adds support for read-only dividers in the sunxi-ng clock
driver. It introduces a new ccu_rodiv_ops structure and updates the rate
determination helper to handle the read-only flag.

> diff --git a/drivers/clk/sunxi-ng/ccu_div.c b/drivers/clk/sunxi-ng/ccu_div.c
> index 62d680ccb524b..93cb4cb93abe8 100644
> --- a/drivers/clk/sunxi-ng/ccu_div.c
> +++ b/drivers/clk/sunxi-ng/ccu_div.c
> @@ -20,8 +20,22 @@ static int ccu_div_determine_rate_helper(struct ccu_mux_internal *mux,
>  	if (cd->common.features & CCU_FEATURE_FIXED_POSTDIV)
>  		req->rate *= cd->fixed_post_div;
>  
> -	ret = divider_determine_rate(&cd->common.hw, req, cd->div.table,
> -				     cd->div.width, cd->div.flags);
> +	if (cd->div.flags & CLK_DIVIDER_READ_ONLY) {
> +		unsigned long val;
> +		u32 reg;
> +
> +		reg = readl(cd->common.base + cd->common.reg);
> +		val = reg >> cd->div.shift;
> +		val &= (1 << cd->div.width) - 1;
> +
> +		ret = divider_ro_determine_rate(&cd->common.hw, req, cd->div.table,
> +						cd->div.width, cd->div.flags, val);

[Severity: High]
This is a pre-existing issue, but could this unvalidated register read cause 
a divide-by-zero kernel panic?

In ccu_div_determine_rate_helper(), the raw register value is read and
passed as 'val' to divider_ro_determine_rate(). If the register contains
an unexpected value from the bootloader (or 0 when CLK_DIVIDER_ONE_BASED
is set) that _get_div() maps to 0, divider_ro_determine_rate() lacks a 
zero-check before calculating:

    req->rate = DIV_ROUND_UP_ULL((u64)req->best_parent_rate, div);

> +
> +	} else {

[ ... ]

> @@ -143,3 +157,15 @@ const struct clk_ops ccu_div_ops = {
>  	.set_rate	= ccu_div_set_rate,
>  };
>  EXPORT_SYMBOL_NS_GPL(ccu_div_ops, "SUNXI_CCU");
> +
> +const struct clk_ops ccu_rodiv_ops = {
> +	.disable	= ccu_div_disable,
> +	.enable		= ccu_div_enable,
> +	.is_enabled	= ccu_div_is_enabled,
> +
> +	.get_parent	= ccu_div_get_parent,
> +
> +	.determine_rate	= ccu_div_determine_rate,
> +	.recalc_rate	= ccu_div_recalc_rate,
> +};

[Severity: High]
Could the missing .set_parent callback in ccu_rodiv_ops lead to a silent
desynchronization between the software clock tree and the hardware?

The struct provides reparenting capabilities via .get_parent and
.determine_rate, but omits .set_parent. If a rate request causes
ccu_mux_helper_determine_rate() to evaluate and select a new parent, the
Common Clock Framework will apply this new parent in software but skip
updating the hardware since .set_parent is NULL. 

This would leave all downstream clock rate calculations incorrect.

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260717-a733-rtc-v5-0-3874cc26abf7@baylibre.com?part=2

[PATCH v5 3/4] clk: sunxi-ng: sun6i-rtc: split main oscillator div and gate.

[Jerome Brunet]

On the a733 the "osc24M-32k" clock has the same gate bits as the previously
supported SoC but a different divider implementation.

Instead of a fixed 750 divider, the divider is selected based on the
rate of the oscillator. It can be seen as a simple read-only divider.

On the A733 the gate and the divider are on different register which is
not supported by sunxi combined clocks. These element will be split on the
A733. Split them for the older SoC as well to keep on sharing the gate
definition.

Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
 drivers/clk/sunxi-ng/ccu-sun6i-rtc.c | 20 +++++++++++---------
 drivers/clk/sunxi-ng/ccu-sun6i-rtc.h |  3 ++-
 2 files changed, 13 insertions(+), 10 deletions(-)

diff --git a/drivers/clk/sunxi-ng/ccu-sun6i-rtc.c b/drivers/clk/sunxi-ng/ccu-sun6i-rtc.c
index b24c8b196e66..25dd87e78eb7 100644
--- a/drivers/clk/sunxi-ng/ccu-sun6i-rtc.c
+++ b/drivers/clk/sunxi-ng/ccu-sun6i-rtc.c
@@ -218,17 +218,18 @@ static const struct clk_parent_data osc24M[] = {
 	{ .fw_name = "hosc", .name = "osc24M" }
 };
 
-static struct ccu_gate osc24M_32k_clk = {
-	.enable	= BIT(16),
-	.common	= {
-		.reg		= LOSC_OUT_GATING_REG,
-		.prediv		= 750,
-		.features	= CCU_FEATURE_ALL_PREDIV,
-		.hw.init	= CLK_HW_INIT_PARENTS_DATA("osc24M-32k", osc24M,
-							   &ccu_gate_ops, 0),
-	},
+static struct clk_fixed_factor osc24M_32k_div_clk = {
+	.mult = 1,
+	.div = 750,
+	.hw.init = CLK_HW_INIT_PARENTS_DATA("osc24M-32k-div",
+					    osc24M,
+					    &clk_fixed_factor_ops,
+					    0),
 };
 
+static SUNXI_CCU_GATE_HW(osc24M_32k_clk, "osc24M-32k", &osc24M_32k_div_clk.hw,
+			 LOSC_OUT_GATING_REG, BIT(16), 0);
+
 static const struct clk_hw *rtc_32k_parents[] = {
 	&osc32k_clk.common.hw,
 	&osc24M_32k_clk.common.hw
@@ -286,6 +287,7 @@ static struct clk_hw_onecell_data sun6i_rtc_ccu_hw_clks = {
 		[CLK_EXT_OSC32K_GATE]	= &ext_osc32k_gate_clk.common.hw,
 		[CLK_OSC24M_32K]	= &osc24M_32k_clk.common.hw,
 		[CLK_RTC_32K]		= &rtc_32k_clk.common.hw,
+		[CLK_OSC24M_32K_DIV]	= &osc24M_32k_div_clk.hw,
 	},
 };
 
diff --git a/drivers/clk/sunxi-ng/ccu-sun6i-rtc.h b/drivers/clk/sunxi-ng/ccu-sun6i-rtc.h
index 9ae821fc2599..ab7b92b47f59 100644
--- a/drivers/clk/sunxi-ng/ccu-sun6i-rtc.h
+++ b/drivers/clk/sunxi-ng/ccu-sun6i-rtc.h
@@ -9,7 +9,8 @@
 #define CLK_EXT_OSC32K_GATE	4
 #define CLK_OSC24M_32K		5
 #define CLK_RTC_32K		6
+#define CLK_OSC24M_32K_DIV	7
 
-#define CLK_NUMBER		(CLK_RTC_32K + 1)
+#define CLK_NUMBER		(CLK_OSC24M_32K_DIV + 1)
 
 #endif /* _CCU_SUN6I_RTC_H */

-- 
2.47.3

Re: [PATCH v5 3/4] clk: sunxi-ng: sun6i-rtc: split main oscillator div and gate.

[sashiko-bot]

> On the a733 the "osc24M-32k" clock has the same gate bits as the previously
> supported SoC but a different divider implementation.
> 
> Instead of a fixed 750 divider, the divider is selected based on the
> rate of the oscillator. It can be seen as a simple read-only divider.
> 
> On the A733 the gate and the divider are on different register which is
> not supported by sunxi combined clocks. These element will be split on the
> A733. Split them for the older SoC as well to keep on sharing the gate
> definition.
> 
> Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

Sashiko has reviewed this patch and found no issues. It looks great!

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260717-a733-rtc-v5-0-3874cc26abf7@baylibre.com?part=3

[PATCH v5 4/4] clk: sunxi-ng: sun6i-rtc: add a733 support

[Jerome Brunet]

Add support for the sun60i a733 CCU RTC.

Compared to the a523, this SoC has a different input oscillator divider
which auto-detects the oscillator rate and select a divider to provide
a fixed 32768Hz clock. It also provides several phy reference clocks
with dedicated clock gates.

Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
 drivers/clk/sunxi-ng/ccu-sun6i-rtc.c | 77 ++++++++++++++++++++++++++++++++++--
 drivers/clk/sunxi-ng/ccu-sun6i-rtc.h |  2 +-
 2 files changed, 75 insertions(+), 4 deletions(-)

diff --git a/drivers/clk/sunxi-ng/ccu-sun6i-rtc.c b/drivers/clk/sunxi-ng/ccu-sun6i-rtc.c
index 25dd87e78eb7..98ae10307f43 100644
--- a/drivers/clk/sunxi-ng/ccu-sun6i-rtc.c
+++ b/drivers/clk/sunxi-ng/ccu-sun6i-rtc.c
@@ -44,9 +44,15 @@
 #define DCXO_CTRL_REG			0x160
 #define DCXO_CTRL_CLK16M_RC_EN		BIT(0)
 
+#define DCXO_GATING_REG			0x16c
+
+#define CLK_NUMBER_NO_GATES		(CLK_OSC24M_32K_DIV + 1)
+
 struct sun6i_rtc_match_data {
 	bool				have_ext_osc32k		: 1;
 	bool				have_iosc_calibration	: 1;
+	bool				have_dcxo_status	: 1;
+	bool				have_phy_ref_gates	: 1;
 	bool				rtc_32k_single_parent	: 1;
 	const struct clk_parent_data	*osc32k_fanout_parents;
 	u8				osc32k_fanout_nparents;
@@ -213,7 +219,12 @@ static struct ccu_mux osc32k_clk = {
 	},
 };
 
-/* This falls back to the global name for fwnodes without a named reference. */
+/*
+ * This falls back to the global name for fwnodes without a named reference.
+ * NOTE: osc24M name might be misleading the oscillator could also be a 26MHz
+ * or a 19.2MHz one starting with the a733. The original name is kept anyway
+ * in case anything is relying on it.
+ */
 static const struct clk_parent_data osc24M[] = {
 	{ .fw_name = "hosc", .name = "osc24M" }
 };
@@ -227,8 +238,30 @@ static struct clk_fixed_factor osc24M_32k_div_clk = {
 					    0),
 };
 
-static SUNXI_CCU_GATE_HW(osc24M_32k_clk, "osc24M-32k", &osc24M_32k_div_clk.hw,
-			 LOSC_OUT_GATING_REG, BIT(16), 0);
+static struct clk_div_table osc24M_32k_div_a733_table[] = {
+	{ .val = 0, .div = 732 },
+	{ .val = 1, .div = 586 },
+	{ .val = 2, .div = 793 },
+	{ .val = 3, .div = 732 },
+	{ /* Sentinel */ },
+};
+
+static struct ccu_div osc24M_32k_div_a733_clk = {
+	.enable = BIT(1),
+	.div	= _SUNXI_CCU_DIV_TABLE_FLAGS(14, 2,
+					     osc24M_32k_div_a733_table,
+					     CLK_DIVIDER_READ_ONLY),
+	.common	= {
+		.reg		= DCXO_CTRL_REG,
+		.hw.init	= CLK_HW_INIT_PARENTS_DATA("osc24M-32k-div",
+							   osc24M,
+							   &ccu_rodiv_ops,
+							   0),
+	},
+};
+
+static SUNXI_CCU_GATE(osc24M_32k_clk, "osc24M-32k", "osc24M-32k-div",
+		      LOSC_OUT_GATING_REG, BIT(16), 0);
 
 static const struct clk_hw *rtc_32k_parents[] = {
 	&osc32k_clk.common.hw,
@@ -267,6 +300,15 @@ static struct ccu_mux osc32k_fanout_clk = {
 	},
 };
 
+static SUNXI_CCU_GATE_FW(hosc_serdes1_clk, "hosc-serdes1", "hosc",
+		      DCXO_GATING_REG, BIT(5), 0);
+static SUNXI_CCU_GATE_FW(hosc_serdes0_clk, "hosc-serdes0", "hosc",
+		      DCXO_GATING_REG, BIT(4), 0);
+static SUNXI_CCU_GATE_FW(hosc_hdmi_clk, "hosc-hdmi", "hosc",
+		      DCXO_GATING_REG, BIT(1), 0);
+static SUNXI_CCU_GATE_FW(hosc_ufs_clk, "hosc-ufs", "hosc",
+		      DCXO_GATING_REG, BIT(0), 0);
+
 static struct ccu_common *sun6i_rtc_ccu_clks[] = {
 	&iosc_clk,
 	&iosc_32k_clk,
@@ -275,6 +317,11 @@ static struct ccu_common *sun6i_rtc_ccu_clks[] = {
 	&osc24M_32k_clk.common,
 	&rtc_32k_clk.common,
 	&osc32k_fanout_clk.common,
+	&osc24M_32k_div_a733_clk.common,
+	&hosc_serdes1_clk.common,
+	&hosc_serdes0_clk.common,
+	&hosc_hdmi_clk.common,
+	&hosc_ufs_clk.common,
 };
 
 static struct clk_hw_onecell_data sun6i_rtc_ccu_hw_clks = {
@@ -288,6 +335,10 @@ static struct clk_hw_onecell_data sun6i_rtc_ccu_hw_clks = {
 		[CLK_OSC24M_32K]	= &osc24M_32k_clk.common.hw,
 		[CLK_RTC_32K]		= &rtc_32k_clk.common.hw,
 		[CLK_OSC24M_32K_DIV]	= &osc24M_32k_div_clk.hw,
+		[CLK_HOSC_UFS]		= &hosc_ufs_clk.common.hw,
+		[CLK_HOSC_HDMI]		= &hosc_hdmi_clk.common.hw,
+		[CLK_HOSC_SERDES0]	= &hosc_serdes0_clk.common.hw,
+		[CLK_HOSC_SERDES1]	= &hosc_serdes1_clk.common.hw,
 	},
 };
 
@@ -330,6 +381,15 @@ static const struct sun6i_rtc_match_data sun55i_a523_rtc_ccu_data = {
 	.osc32k_fanout_nparents	= ARRAY_SIZE(sun50i_r329_osc32k_fanout_parents),
 };
 
+static const struct sun6i_rtc_match_data sun60i_a733_rtc_ccu_data = {
+	.have_ext_osc32k	= true,
+	.have_iosc_calibration	= true,
+	.have_dcxo_status	= true,
+	.have_phy_ref_gates	= true,
+	.osc32k_fanout_parents	= sun50i_r329_osc32k_fanout_parents,
+	.osc32k_fanout_nparents	= ARRAY_SIZE(sun50i_r329_osc32k_fanout_parents),
+};
+
 static const struct of_device_id sun6i_rtc_ccu_match[] = {
 	{
 		.compatible	= "allwinner,sun50i-h616-rtc",
@@ -343,6 +403,10 @@ static const struct of_device_id sun6i_rtc_ccu_match[] = {
 		.compatible	= "allwinner,sun55i-a523-rtc",
 		.data		= &sun55i_a523_rtc_ccu_data,
 	},
+	{
+		.compatible	= "allwinner,sun60i-a733-rtc",
+		.data		= &sun60i_a733_rtc_ccu_data,
+	},
 	{},
 };
 MODULE_DEVICE_TABLE(of, sun6i_rtc_ccu_match);
@@ -375,6 +439,13 @@ int sun6i_rtc_ccu_probe(struct device *dev, void __iomem *reg)
 	osc32k_fanout_init_data.parent_data = data->osc32k_fanout_parents;
 	osc32k_fanout_init_data.num_parents = data->osc32k_fanout_nparents;
 
+	if (data->have_dcxo_status)
+		sun6i_rtc_ccu_hw_clks.hws[CLK_OSC24M_32K_DIV] =
+			&osc24M_32k_div_a733_clk.common.hw;
+
+	if (!data->have_phy_ref_gates)
+		sun6i_rtc_ccu_hw_clks.num = CLK_NUMBER_NO_GATES;
+
 	return devm_sunxi_ccu_probe(dev, reg, &sun6i_rtc_ccu_desc);
 }
 
diff --git a/drivers/clk/sunxi-ng/ccu-sun6i-rtc.h b/drivers/clk/sunxi-ng/ccu-sun6i-rtc.h
index ab7b92b47f59..4f4f4cb00f1d 100644
--- a/drivers/clk/sunxi-ng/ccu-sun6i-rtc.h
+++ b/drivers/clk/sunxi-ng/ccu-sun6i-rtc.h
@@ -11,6 +11,6 @@
 #define CLK_RTC_32K		6
 #define CLK_OSC24M_32K_DIV	7
 
-#define CLK_NUMBER		(CLK_OSC24M_32K_DIV + 1)
+#define CLK_NUMBER		(CLK_HOSC_SERDES1 + 1)
 
 #endif /* _CCU_SUN6I_RTC_H */

-- 
2.47.3

Re: [PATCH v5 4/4] clk: sunxi-ng: sun6i-rtc: add a733 support

[sashiko-bot]

> Add support for the sun60i a733 CCU RTC.
> 
> Compared to the a523, this SoC has a different input oscillator divider
> which auto-detects the oscillator rate and select a divider to provide
> a fixed 32768Hz clock. It also provides several phy reference clocks
> with dedicated clock gates.
> 
> Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

Sashiko has reviewed this patch and found no issues. It looks great!

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260717-a733-rtc-v5-0-3874cc26abf7@baylibre.com?part=4