[PATCH v2 3/7] dt-bindings: display: tegra: Document 8-bit CPU parallel interface

[Svyatoslav Ryhel <clamor95@gmail.com>]

Document 8-bit CPU parallel MIPI DBI Type B interface provided by
Tegra20/30 SoCs display controller.

Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
---
 .../display/tegra/nvidia,tegra-dbi.yaml       | 143 ++++++++++++++++++
 .../display/tegra/nvidia,tegra20-dc.yaml      |   3 +
 2 files changed, 146 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/tegra/nvidia,tegra-dbi.yaml

diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra-dbi.yaml b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra-dbi.yaml
new file mode 100644
index 0000000000000..184c33d436308
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra-dbi.yaml
@@ -0,0 +1,143 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra-dbi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Nvidia Tegra DC based MIPI DBI Type B interface
+
+maintainers:
+  - Svyatoslav Ryhel <clamor95@gmail.com>
+
+description: The display controller in Tegra20/30 SoCs features an
+  8-bit SPI interface that closely resembles the MIPI DBI Type B
+  protocol and is referred to as '8-bit CPU'. Each display controller
+  provides two such interfaces, which can be used to send MIPI DCS
+  commands to initialize and control the panel while image data is
+  transmitted via 16/18/24-line RGB.
+
+properties:
+  dc-gpios:
+    description: Data/command selection pin.
+    maxItems: 1
+
+  rw-gpios:
+    description: Read/write pin.
+    maxItems: 1
+
+  cs-gpios:
+    description: Chip select pin.
+    maxItems: 1
+
+  data-gpios:
+    description: Specifies a set of 8 gpio pins used to transfer data.
+    minItems: 8
+    maxItems: 8
+
+  nvidia,init-sequence:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    description:
+      Device specific set of values used in DC DISP_SPI_INIT_SEQ registers.
+    minItems: 4
+    maxItems: 4
+
+  panel:
+    type: object
+    description: Node of supported panel driven by the bridge.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description: Video port for RGB input.
+
+        properties:
+          endpoint:
+            $ref: /schemas/graph.yaml#/$defs/endpoint-base
+            unevaluatedProperties: false
+
+            properties:
+              bus-width:
+                enum: [ 16, 18, 24 ]
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Video port for DBI output (panel or connector).
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - dc-gpios
+  - rw-gpios
+  - cs-gpios
+  - data-gpios
+  - panel
+  - ports
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    dc@54200000 {
+        reg = <0x54200000 0x00040000>;
+
+        dbi {
+            dc-gpios = <&gpio 110 GPIO_ACTIVE_HIGH>;
+            rw-gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
+            cs-gpios = <&gpio 108 GPIO_ACTIVE_HIGH>;
+
+            data-gpios = <&gpio 32 GPIO_ACTIVE_HIGH>, <&gpio 33 GPIO_ACTIVE_HIGH>,
+                         <&gpio 34 GPIO_ACTIVE_HIGH>, <&gpio 35 GPIO_ACTIVE_HIGH>,
+                         <&gpio 36 GPIO_ACTIVE_HIGH>, <&gpio 37 GPIO_ACTIVE_HIGH>,
+                         <&gpio 38 GPIO_ACTIVE_HIGH>, <&gpio 39 GPIO_ACTIVE_HIGH>;
+
+            nvidia,init-sequence = <0x0000002c 0x0 0x0 0x00005000>;
+
+            panel {
+                compatible = "hit,tx10d07vm0baa";
+
+                reset-gpios = <&gpio 175 GPIO_ACTIVE_LOW>;
+
+                avci-supply = <&vcc_2v8_lcd>;
+                iovcc-supply = <&iovcc_1v8_lcd>;
+
+                backlight = <&backlight>;
+
+                port {
+                    panel_input: endpoint {
+                        remote-endpoint = <&bridge_output>;
+                    };
+                };
+            };
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+
+                    bridge_input: endpoint {
+                        remote-endpoint = <&dpi_output>;
+                        bus-width = <24>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+
+                    bridge_output: endpoint {
+                        remote-endpoint = <&panel_input>;
+                    };
+                };
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-dc.yaml b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-dc.yaml
index 69be95afd5627..bb280f8dbfc7c 100644
--- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-dc.yaml
+++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-dc.yaml
@@ -76,6 +76,9 @@ properties:
     $ref: /schemas/types.yaml#/definitions/phandle-array
     description: A list of phandles of outputs that this display controller can drive.
 
+  dbi:
+    $ref: /schemas/display/tegra/nvidia,tegra-dbi.yaml#
+
   rgb:
     type: object
 
-- 
2.53.0