[PATCH v1 0/8] Enable audio on qcs6490-RB3Gen2 and qcm6490-idp boards

[PATCH v1 0/8] Enable audio on qcs6490-RB3Gen2 and qcm6490-idp boards

[Prasad Kumpatla]

From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>

Audio support is now enabled on the qcs6490-RB3Gen2 and qcm6490-idp boards.
The updates include adding the necessary audio device tree support and the required
dependencies.

Both the qcs6490-RB3Gen2 and qcm6490-idp boards are derived from the same SoC 
platform. Therefore, the audio support changes are included in a single patch 
set for consistency and ease of maintenance.

Mohammad Rafi Shaik (8):
  arm64: dts: qcom: sc7280: Add gpr node
  arm64: dts: qcom: sc7280: Add WSA SoundWire and LPASS support
  arm64: dts: qcom: qcs6490-rb3gen2: Modify WSA and VA macro clock nodes
    for audioreach solution
  arm64: dts: qcom: qcs6490-rb3gen2: add WSA8830 speakers
  arm64: dts: qcom: qcs6490-rb3gen2: Add sound card
  arm64: dts: qcom: qcm6490-idp: Modify WSA/VA/RX/TX macro clock nodes
    for audioreach solution
  arm64: dts: qcom: qcm6490-idp: Add WSA8830 speakers and WCD9370
    headset codec
  arm64: dts: qcom: qcm6490-idp: Add sound card

 arch/arm64/boot/dts/qcom/qcm6490-idp.dts     | 282 +++++++++++++++++++
 arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 138 +++++++++
 arch/arm64/boot/dts/qcom/sc7280.dtsi         | 105 +++++++
 3 files changed, 525 insertions(+)

-- 
2.34.1

[PATCH v1 1/8] arm64: dts: qcom: sc7280: Add gpr node

[Prasad Kumpatla]

From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>

Add GPR node along with APM(Audio Process Manager) and PRM(Proxy
resource Manager) audio services.

Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
---
 arch/arm64/boot/dts/qcom/sc7280.dtsi | 37 ++++++++++++++++++++++++++++
 1 file changed, 37 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 0f2caf36910b..39fbd3c40e47 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -25,6 +25,8 @@
 #include <dt-bindings/reset/qcom,sdm845-aoss.h>
 #include <dt-bindings/reset/qcom,sdm845-pdc.h>
 #include <dt-bindings/soc/qcom,apr.h>
+#include <dt-bindings/soc/qcom,gpr.h>
+#include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
 #include <dt-bindings/sound/qcom,lpass.h>
 #include <dt-bindings/thermal/thermal.h>
@@ -3857,6 +3859,41 @@ q6routing: routing {
 					};
 				};
 
+				gpr {
+					compatible = "qcom,gpr";
+					qcom,glink-channels = "adsp_apps";
+					qcom,domain = <GPR_DOMAIN_ID_ADSP>;
+					qcom,intents = <512 20>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					q6apm: service@1 {
+						compatible = "qcom,q6apm";
+						reg = <GPR_APM_MODULE_IID>;
+						#sound-dai-cells = <0>;
+
+						q6apmdai: dais {
+							compatible = "qcom,q6apm-dais";
+							iommus = <&apps_smmu 0x1801 0x0>;
+						};
+
+						q6apmbedai: bedais {
+							compatible = "qcom,q6apm-lpass-dais";
+							#sound-dai-cells = <1>;
+						};
+					};
+
+					q6prm: service@2 {
+						compatible = "qcom,q6prm";
+						reg = <GPR_PRM_MODULE_IID>;
+
+						q6prmcc: clock-controller {
+							compatible = "qcom,q6prm-lpass-clocks";
+							#clock-cells = <2>;
+						};
+					};
+				};
+
 				fastrpc {
 					compatible = "qcom,fastrpc";
 					qcom,glink-channels = "fastrpcglink-apps-dsp";
-- 
2.34.1

Re: [PATCH v1 1/8] arm64: dts: qcom: sc7280: Add gpr node

[Bryan O'Donoghue]

On 17/03/2025 05:41, Prasad Kumpatla wrote:
> Add GPR node along with APM(Audio Process Manager) and PRM(Proxy
> resource Manager) audio services.

Nitpick.

You've defined APM and RPM but not GPR.

Your triumvirate of TLAs is missing 1/3 !

Please add.

---
bod

Re: [PATCH v1 1/8] arm64: dts: qcom: sc7280: Add gpr node

[Prasad Kumpatla]

On 3/27/2025 4:21 AM, Bryan O'Donoghue wrote:
> On 17/03/2025 05:41, Prasad Kumpatla wrote:
>> Add GPR node along with APM(Audio Process Manager) and PRM(Proxy
>> resource Manager) audio services.
>
> Nitpick.
>
> You've defined APM and RPM but not GPR.
>
> Your triumvirate of TLAs is missing 1/3 !
>
> Please add.

Ack, Will update in next patchset version.

Thanks,
Prasad

>
> ---
> bod

[PATCH v1 2/8] arm64: dts: qcom: sc7280: Add WSA SoundWire and LPASS support

[Prasad Kumpatla]

From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>

Add WSA macroLPASS Codecs along with SoundWire controller.

Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
---
 arch/arm64/boot/dts/qcom/sc7280.dtsi | 68 ++++++++++++++++++++++++++++
 1 file changed, 68 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 39fbd3c40e47..90b2f6e2b7c0 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -2602,6 +2602,64 @@ swr1: soundwire@3230000 {
 			status = "disabled";
 		};
 
+		lpass_wsa_macro: codec@3240000 {
+			compatible = "qcom,sc7280-lpass-wsa-macro";
+			reg = <0x0 0x03240000 0x0 0x1000>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&lpass_wsa_swr_clk>, <&lpass_wsa_swr_data>;
+
+			clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>,
+				 <&lpass_aon LPASS_AON_CC_TX_MCLK_2X_CLK>,
+				 <&lpass_va_macro>;
+			clock-names = "mclk", "npl", "fsgen";
+
+			power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
+					<&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
+			power-domain-names = "macro", "dcodec";
+
+			#clock-cells = <0>;
+			clock-output-names = "mclk";
+			#sound-dai-cells = <1>;
+
+			status = "disabled";
+		};
+
+		swr2: soundwire@3250000 {
+			compatible = "qcom,soundwire-v1.6.0";
+			reg = <0x0 0x03250000 0x0 0x2000>;
+
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&lpass_wsa_macro>;
+			clock-names = "iface";
+
+			qcom,din-ports = <2>;
+			qcom,dout-ports = <6>;
+
+			resets = <&lpass_audiocc LPASS_AUDIO_SWR_WSA_CGCR>;
+			reset-names = "swr_audio_cgcr";
+
+			qcom,ports-sinterval-low = /bits/ 8 <0x07 0x1f 0x3f 0x07
+								0x1f 0x3f 0x0f 0x0f>;
+			qcom,ports-offset1 = /bits/ 8 <0x01 0x02 0x0c 0x06 0x12 0x0d 0x07 0x0a>;
+			qcom,ports-offset2 = /bits/ 8 <0xff 0x00 0x1f 0xff 0x00 0x1f 0x00 0x00>;
+			qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+			qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+			qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+			qcom,ports-block-pack-mode = /bits/ 8 <0xff 0xff 0x01 0xff 0xff 0x01
+							       0xff 0xff>;
+			qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff
+								0xff 0xff>;
+			qcom,ports-lane-control = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff
+							    0xff 0xff>;
+
+			#address-cells = <2>;
+			#size-cells = <0>;
+			#sound-dai-cells = <1>;
+
+			status = "disabled";
+		};
+
 		lpass_audiocc: clock-controller@3300000 {
 			compatible = "qcom,sc7280-lpassaudiocc";
 			reg = <0 0x03300000 0 0x30000>,
@@ -2808,6 +2866,16 @@ lpass_tx_swr_data: tx-swr-data-state {
 				pins = "gpio1", "gpio2", "gpio14";
 				function = "swr_tx_data";
 			};
+
+			lpass_wsa_swr_clk: wsa-swr-clk-state {
+				pins = "gpio10";
+				function = "wsa_swr_clk";
+			};
+
+			lpass_wsa_swr_data: wsa-swr-data-state {
+				pins = "gpio11";
+				function = "wsa_swr_data";
+			};
 		};
 
 		gpu: gpu@3d00000 {
-- 
2.34.1

Re: [PATCH v1 2/8] arm64: dts: qcom: sc7280: Add WSA SoundWire and LPASS support

[Bryan O'Donoghue]

On 17/03/2025 05:41, Prasad Kumpatla wrote:
> From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
> 
> Add WSA macroLPASS Codecs along with SoundWire controller.
> 
> Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
> Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
> Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
> ---
>   arch/arm64/boot/dts/qcom/sc7280.dtsi | 68 ++++++++++++++++++++++++++++
>   1 file changed, 68 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> index 39fbd3c40e47..90b2f6e2b7c0 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> @@ -2602,6 +2602,64 @@ swr1: soundwire@3230000 {
>   			status = "disabled";
>   		};
> 
> +		lpass_wsa_macro: codec@3240000 {
> +			compatible = "qcom,sc7280-lpass-wsa-macro";
> +			reg = <0x0 0x03240000 0x0 0x1000>;
> +
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&lpass_wsa_swr_clk>, <&lpass_wsa_swr_data>;
> +
> +			clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>,
> +				 <&lpass_aon LPASS_AON_CC_TX_MCLK_2X_CLK>,
> +				 <&lpass_va_macro>;
> +			clock-names = "mclk", "npl", "fsgen";

clocks* go before pinctrl*

> +
> +			power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
> +					<&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
> +			power-domain-names = "macro", "dcodec";
> +
> +			#clock-cells = <0>;
> +			clock-output-names = "mclk";
> +			#sound-dai-cells = <1>;
> +
> +			status = "disabled";
> +		};
> +
> +		swr2: soundwire@3250000 {
> +			compatible = "qcom,soundwire-v1.6.0";
> +			reg = <0x0 0x03250000 0x0 0x2000>;
> +
> +			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&lpass_wsa_macro>;
> +			clock-names = "iface";
> +
> +			qcom,din-ports = <2>;
> +			qcom,dout-ports = <6>;
> +
> +			resets = <&lpass_audiocc LPASS_AUDIO_SWR_WSA_CGCR>;
> +			reset-names = "swr_audio_cgcr";

vendor prefixes should come after standard names

Documentation/devicetree/bindings/dts-coding-style.rst
"Order of Properties in Device Node"

> +
> +			qcom,ports-sinterval-low = /bits/ 8 <0x07 0x1f 0x3f 0x07
> +								0x1f 0x3f 0x0f 0x0f>;
> +			qcom,ports-offset1 = /bits/ 8 <0x01 0x02 0x0c 0x06 0x12 0x0d 0x07 0x0a>;
> +			qcom,ports-offset2 = /bits/ 8 <0xff 0x00 0x1f 0xff 0x00 0x1f 0x00 0x00>;
> +			qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> +			qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> +			qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> +			qcom,ports-block-pack-mode = /bits/ 8 <0xff 0xff 0x01 0xff 0xff 0x01
> +							       0xff 0xff>;
> +			qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff
> +								0xff 0xff>;
> +			qcom,ports-lane-control = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff
> +							    0xff 0xff>;
> +
> +			#address-cells = <2>;
> +			#size-cells = <0>;
> +			#sound-dai-cells = <1>;
> +
> +			status = "disabled";
> +		};
> +
>   		lpass_audiocc: clock-controller@3300000 {
>   			compatible = "qcom,sc7280-lpassaudiocc";
>   			reg = <0 0x03300000 0 0x30000>,
> @@ -2808,6 +2866,16 @@ lpass_tx_swr_data: tx-swr-data-state {
>   				pins = "gpio1", "gpio2", "gpio14";
>   				function = "swr_tx_data";
>   			};
> +
> +			lpass_wsa_swr_clk: wsa-swr-clk-state {
> +				pins = "gpio10";
> +				function = "wsa_swr_clk";
> +			};
> +
> +			lpass_wsa_swr_data: wsa-swr-data-state {
> +				pins = "gpio11";
> +				function = "wsa_swr_data";
> +			};
>   		};
> 
>   		gpu: gpu@3d00000 {
> --
> 2.34.1
> 
> 

Re: [PATCH v1 2/8] arm64: dts: qcom: sc7280: Add WSA SoundWire and LPASS support

[Prasad Kumpatla]

On 3/27/2025 4:32 AM, Bryan O'Donoghue wrote:
> On 17/03/2025 05:41, Prasad Kumpatla wrote:
>> From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
>>
>> Add WSA macroLPASS Codecs along with SoundWire controller.
>>
>> Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
>> Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
>> Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
>> ---
>>   arch/arm64/boot/dts/qcom/sc7280.dtsi | 68 ++++++++++++++++++++++++++++
>>   1 file changed, 68 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi 
>> b/arch/arm64/boot/dts/qcom/sc7280.dtsi
>> index 39fbd3c40e47..90b2f6e2b7c0 100644
>> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
>> @@ -2602,6 +2602,64 @@ swr1: soundwire@3230000 {
>>               status = "disabled";
>>           };
>>
>> +        lpass_wsa_macro: codec@3240000 {
>> +            compatible = "qcom,sc7280-lpass-wsa-macro";
>> +            reg = <0x0 0x03240000 0x0 0x1000>;
>> +
>> +            pinctrl-names = "default";
>> +            pinctrl-0 = <&lpass_wsa_swr_clk>, <&lpass_wsa_swr_data>;
>> +
>> +            clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>,
>> +                 <&lpass_aon LPASS_AON_CC_TX_MCLK_2X_CLK>,
>> +                 <&lpass_va_macro>;
>> +            clock-names = "mclk", "npl", "fsgen";
>
> clocks* go before pinctrl*
ACK,
>
>> +
>> +            power-domains = <&lpass_hm 
>> LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
>> +                    <&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
>> +            power-domain-names = "macro", "dcodec";
>> +
>> +            #clock-cells = <0>;
>> +            clock-output-names = "mclk";
>> +            #sound-dai-cells = <1>;
>> +
>> +            status = "disabled";
>> +        };
>> +
>> +        swr2: soundwire@3250000 {
>> +            compatible = "qcom,soundwire-v1.6.0";
>> +            reg = <0x0 0x03250000 0x0 0x2000>;
>> +
>> +            interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
>> +            clocks = <&lpass_wsa_macro>;
>> +            clock-names = "iface";
>> +
>> +            qcom,din-ports = <2>;
>> +            qcom,dout-ports = <6>;
>> +
>> +            resets = <&lpass_audiocc LPASS_AUDIO_SWR_WSA_CGCR>;
>> +            reset-names = "swr_audio_cgcr";
>
> vendor prefixes should come after standard names
>
> Documentation/devicetree/bindings/dts-coding-style.rst
> "Order of Properties in Device Node"

ACK, will check and update in next patch version.

Thanks,
Prasad

>
>> +
>> +            qcom,ports-sinterval-low = /bits/ 8 <0x07 0x1f 0x3f 0x07
>> +                                0x1f 0x3f 0x0f 0x0f>;
>> +            qcom,ports-offset1 = /bits/ 8 <0x01 0x02 0x0c 0x06 0x12 
>> 0x0d 0x07 0x0a>;
>> +            qcom,ports-offset2 = /bits/ 8 <0xff 0x00 0x1f 0xff 0x00 
>> 0x1f 0x00 0x00>;
>> +            qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 
>> 0xff 0xff 0xff>;
>> +            qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 
>> 0xff 0xff 0xff>;
>> +            qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff 
>> 0xff 0xff 0xff 0xff>;
>> +            qcom,ports-block-pack-mode = /bits/ 8 <0xff 0xff 0x01 
>> 0xff 0xff 0x01
>> +                                   0xff 0xff>;
>> +            qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 
>> 0xff 0xff 0xff
>> +                                0xff 0xff>;
>> +            qcom,ports-lane-control = /bits/ 8 <0xff 0xff 0xff 0xff 
>> 0xff 0xff
>> +                                0xff 0xff>;
>> +
>> +            #address-cells = <2>;
>> +            #size-cells = <0>;
>> +            #sound-dai-cells = <1>;
>> +
>> +            status = "disabled";
>> +        };
>> +
>>           lpass_audiocc: clock-controller@3300000 {
>>               compatible = "qcom,sc7280-lpassaudiocc";
>>               reg = <0 0x03300000 0 0x30000>,
>> @@ -2808,6 +2866,16 @@ lpass_tx_swr_data: tx-swr-data-state {
>>                   pins = "gpio1", "gpio2", "gpio14";
>>                   function = "swr_tx_data";
>>               };
>> +
>> +            lpass_wsa_swr_clk: wsa-swr-clk-state {
>> +                pins = "gpio10";
>> +                function = "wsa_swr_clk";
>> +            };
>> +
>> +            lpass_wsa_swr_data: wsa-swr-data-state {
>> +                pins = "gpio11";
>> +                function = "wsa_swr_data";
>> +            };
>>           };
>>
>>           gpu: gpu@3d00000 {
>> -- 
>> 2.34.1
>>
>>
>

Re: [PATCH v1 2/8] arm64: dts: qcom: sc7280: Add WSA SoundWire and LPASS support

[Dmitry Baryshkov]

On Mon, Mar 17, 2025 at 11:11:45AM +0530, Prasad Kumpatla wrote:
> From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
> 
> Add WSA macroLPASS Codecs along with SoundWire controller.
> 
> Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
> Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
> Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
> ---
>  arch/arm64/boot/dts/qcom/sc7280.dtsi | 68 ++++++++++++++++++++++++++++
>  1 file changed, 68 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> index 39fbd3c40e47..90b2f6e2b7c0 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> @@ -2602,6 +2602,64 @@ swr1: soundwire@3230000 {
>  			status = "disabled";
>  		};
>  
> +		lpass_wsa_macro: codec@3240000 {
> +			compatible = "qcom,sc7280-lpass-wsa-macro";
> +			reg = <0x0 0x03240000 0x0 0x1000>;
> +
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&lpass_wsa_swr_clk>, <&lpass_wsa_swr_data>;

pinctrl-N
pinctrl-names

> +
> +			clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>,
> +				 <&lpass_aon LPASS_AON_CC_TX_MCLK_2X_CLK>,
> +				 <&lpass_va_macro>;
> +			clock-names = "mclk", "npl", "fsgen";
> +

-- 
With best wishes
Dmitry

Re: [PATCH v1 2/8] arm64: dts: qcom: sc7280: Add WSA SoundWire and LPASS support

[Prasad Kumpatla]

On 3/27/2025 7:42 PM, Dmitry Baryshkov wrote:
> On Mon, Mar 17, 2025 at 11:11:45AM +0530, Prasad Kumpatla wrote:
>> From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
>>
>> Add WSA macroLPASS Codecs along with SoundWire controller.
>>
>> Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
>> Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
>> Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
>> ---
>>   arch/arm64/boot/dts/qcom/sc7280.dtsi | 68 ++++++++++++++++++++++++++++
>>   1 file changed, 68 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
>> index 39fbd3c40e47..90b2f6e2b7c0 100644
>> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
>> @@ -2602,6 +2602,64 @@ swr1: soundwire@3230000 {
>>   			status = "disabled";
>>   		};
>>   
>> +		lpass_wsa_macro: codec@3240000 {
>> +			compatible = "qcom,sc7280-lpass-wsa-macro";
>> +			reg = <0x0 0x03240000 0x0 0x1000>;
>> +
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&lpass_wsa_swr_clk>, <&lpass_wsa_swr_data>;
> pinctrl-N
> pinctrl-names

ACK, will takecare on next patchset version.

Thanks,
Prasad

>
>> +
>> +			clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>,
>> +				 <&lpass_aon LPASS_AON_CC_TX_MCLK_2X_CLK>,
>> +				 <&lpass_va_macro>;
>> +			clock-names = "mclk", "npl", "fsgen";
>> +

[PATCH v1 3/8] arm64: dts: qcom: qcs6490-rb3gen2: Modify WSA and VA macro clock nodes for audioreach solution

[Prasad Kumpatla]

From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>

Modify and enable WSA, VA and lpass_tlmm clock properties.
For audioreach solution mclk, npl and fsgen clocks
are enabled through the q6prm clock driver.

Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
---
 arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 31 ++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
index 7a36c90ad4ec..23dea375c213 100644
--- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
+++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
@@ -12,6 +12,7 @@
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
 #include "sc7280.dtsi"
 #include "pm7250b.dtsi"
 #include "pm7325.dtsi"
@@ -666,6 +667,36 @@ redriver_usb_con_sbu: endpoint {
 	};
 };
 
+&lpass_tlmm {
+	clocks = <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+	clock-names = "core", "audio";
+};
+
+&lpass_va_macro {
+	/delete-property/ power-domains;
+	/delete-property/ power-domain-names;
+	clocks = <&q6prmcc LPASS_CLK_ID_VA_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+	clock-names = "mclk", "macro", "dcodec";
+
+	status = "okay";
+};
+
+&lpass_wsa_macro {
+	/delete-property/ power-domains;
+	/delete-property/ power-domain-names;
+	clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&q6prmcc LPASS_CLK_ID_TX_CORE_NPL_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&lpass_va_macro>;
+	clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
+
+	status = "okay";
+};
+
 &mdss {
 	status = "okay";
 };
-- 
2.34.1

Re: [PATCH v1 3/8] arm64: dts: qcom: qcs6490-rb3gen2: Modify WSA and VA macro clock nodes for audioreach solution

[Konrad Dybcio]

On 3/17/25 6:41 AM, Prasad Kumpatla wrote:
> From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
> 
> Modify and enable WSA, VA and lpass_tlmm clock properties.
> For audioreach solution mclk, npl and fsgen clocks
> are enabled through the q6prm clock driver.
> 
> Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
> Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
> Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
> ---

Instead, put the inverse changes in sc7280-chrome-common.dtsi please

Konrad

Re: [PATCH v1 3/8] arm64: dts: qcom: qcs6490-rb3gen2: Modify WSA and VA macro clock nodes for audioreach solution

[Luca Weiss]

Hi Konrad,

On Tue Apr 1, 2025 at 6:05 PM CEST, Konrad Dybcio wrote:
> On 3/17/25 6:41 AM, Prasad Kumpatla wrote:
>> From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
>> 
>> Modify and enable WSA, VA and lpass_tlmm clock properties.
>> For audioreach solution mclk, npl and fsgen clocks
>> are enabled through the q6prm clock driver.
>> 
>> Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
>> Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
>> Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
>> ---
>
> Instead, put the inverse changes in sc7280-chrome-common.dtsi please

How are we going to handle other sc7280-based platforms, such as my
QCM6490 Fairphone 5 needing to use q6afecc instead of q6prmcc which gets
used in this patchset?

One solution might be to put q6afecc into the base sc7280.dtsi file,
then we have a sc7280-audioreach.dtsi which overwrites q6afecc with
q6prmcc which then gets included by boards using audioreach.

I also don't think we can split this across sc7280 vs qcm6490 vs sm7325,
there seems to be any combination possible on any of these SoCs -
depending on the firmware shipped with it.

So somewhat similar to the current sc7280-chrome-common.dtsi but just
for audioreach.

Regards
Luca

>
> Konrad

Re: [PATCH v1 3/8] arm64: dts: qcom: qcs6490-rb3gen2: Modify WSA and VA macro clock nodes for audioreach solution

[Prasad Kumpatla]

On 4/4/2025 12:42 PM, Luca Weiss wrote:
> Hi Konrad,
> 
> On Tue Apr 1, 2025 at 6:05 PM CEST, Konrad Dybcio wrote:
>> On 3/17/25 6:41 AM, Prasad Kumpatla wrote:
>>> From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
>>>
>>> Modify and enable WSA, VA and lpass_tlmm clock properties.
>>> For audioreach solution mclk, npl and fsgen clocks
>>> are enabled through the q6prm clock driver.
>>>
>>> Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
>>> Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
>>> Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
>>> ---
>>
>> Instead, put the inverse changes in sc7280-chrome-common.dtsi please
> 
> How are we going to handle other sc7280-based platforms, such as my
> QCM6490 Fairphone 5 needing to use q6afecc instead of q6prmcc which gets
> used in this patchset?
> 
> One solution might be to put q6afecc into the base sc7280.dtsi file,
> then we have a sc7280-audioreach.dtsi which overwrites q6afecc with
> q6prmcc which then gets included by boards using audioreach.
> 
> I also don't think we can split this across sc7280 vs qcm6490 vs sm7325,
> there seems to be any combination possible on any of these SoCs -
> depending on the firmware shipped with it.
> 
> So somewhat similar to the current sc7280-chrome-common.dtsi but just
> for audioreach.
> 
> Regards
> Luca
ACK, We will handle in next patchset version by creating a new 
qcs6490-audioreach.dtsi file.

Thanks,
Prasad>
>>
>> Konrad
> 

[PATCH v1 4/8] arm64: dts: qcom: qcs6490-rb3gen2: add WSA8830 speakers amplifier

[Prasad Kumpatla]

From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>

Add nodes for WSA8830 speakers amplifier on qcs6490-rb3gen2 board.

Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
---
 arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 27 ++++++++++++++++++++
 1 file changed, 27 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
index 23dea375c213..a1a3df77ad57 100644
--- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
+++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
@@ -870,6 +870,33 @@ &sdhc_2 {
 	status = "okay";
 };
 
+&swr2 {
+	qcom,din-ports = <0>;
+	qcom,dout-ports = <8>;
+
+	left_spkr: speaker@0,1 {
+		compatible = "sdw10217020200";
+		reg = <0 1>;
+		powerdown-gpios = <&tlmm 158 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrLeft";
+		#thermal-sensor-cells = <0>;
+		vdd-supply = <&vreg_l18b_1p8>;
+		qcom,port-mapping = <1 2 3 7>;
+	};
+
+	right_spkr: speaker@0,2 {
+		compatible = "sdw10217020200";
+		reg = <0 2>;
+		powerdown-gpios = <&tlmm 158 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrRight";
+		#thermal-sensor-cells = <0>;
+		vdd-supply = <&vreg_l18b_1p8>;
+		qcom,port-mapping = <4 5 6 8>;
+	};
+};
+
 &tlmm {
 	gpio-reserved-ranges = <32 2>, /* ADSP */
 			       <48 4>; /* NFC */
-- 
2.34.1

Re: [PATCH v1 4/8] arm64: dts: qcom: qcs6490-rb3gen2: add WSA8830 speakers amplifier

[Jorge Ramirez]

On 17/03/25 11:11:47, Prasad Kumpatla wrote:
> From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
> 
> Add nodes for WSA8830 speakers amplifier on qcs6490-rb3gen2 board.
> 
> Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
> Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
> Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
> ---
>  arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 27 ++++++++++++++++++++
>  1 file changed, 27 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> index 23dea375c213..a1a3df77ad57 100644
> --- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> +++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> @@ -870,6 +870,33 @@ &sdhc_2 {
>  	status = "okay";
>  };
>  
> +&swr2 {
> +	qcom,din-ports = <0>;
> +	qcom,dout-ports = <8>;

are these number of ports correct? from my unit tests, 8 seems to be out
of bounds (soundwire probe error)

> +
> +	left_spkr: speaker@0,1 {
> +		compatible = "sdw10217020200";
> +		reg = <0 1>;
> +		powerdown-gpios = <&tlmm 158 GPIO_ACTIVE_LOW>;
> +		#sound-dai-cells = <0>;
> +		sound-name-prefix = "SpkrLeft";
> +		#thermal-sensor-cells = <0>;
> +		vdd-supply = <&vreg_l18b_1p8>;
> +		qcom,port-mapping = <1 2 3 7>;
> +	};
> +
> +	right_spkr: speaker@0,2 {
> +		compatible = "sdw10217020200";
> +		reg = <0 2>;
> +		powerdown-gpios = <&tlmm 158 GPIO_ACTIVE_LOW>;
> +		#sound-dai-cells = <0>;
> +		sound-name-prefix = "SpkrRight";
> +		#thermal-sensor-cells = <0>;
> +		vdd-supply = <&vreg_l18b_1p8>;
> +		qcom,port-mapping = <4 5 6 8>;
> +	};
> +};
> +

also, should we enable the soundwire controller?

>  &tlmm {
>  	gpio-reserved-ranges = <32 2>, /* ADSP */
>  			       <48 4>; /* NFC */
> -- 
> 2.34.1
> 

Re: [PATCH v1 4/8] arm64: dts: qcom: qcs6490-rb3gen2: add WSA8830 speakers amplifier

[Prasad Kumpatla]

On 3/26/2025 10:58 PM, Jorge Ramirez wrote:
> On 17/03/25 11:11:47, Prasad Kumpatla wrote:
>> From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
>>
>> Add nodes for WSA8830 speakers amplifier on qcs6490-rb3gen2 board.
>>
>> Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
>> Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
>> Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
>> ---
>>   arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 27 ++++++++++++++++++++
>>   1 file changed, 27 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
>> index 23dea375c213..a1a3df77ad57 100644
>> --- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
>> +++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
>> @@ -870,6 +870,33 @@ &sdhc_2 {
>>   	status = "okay";
>>   };
>>   
>> +&swr2 {
>> +	qcom,din-ports = <0>;
>> +	qcom,dout-ports = <8>;
> 
> are these number of ports correct? from my unit tests, 8 seems to be out
> of bounds (soundwire probe error)

ACK,
Will fix it in next patchset version.

> 
>> +
>> +	left_spkr: speaker@0,1 {
>> +		compatible = "sdw10217020200";
>> +		reg = <0 1>;
>> +		powerdown-gpios = <&tlmm 158 GPIO_ACTIVE_LOW>;
>> +		#sound-dai-cells = <0>;
>> +		sound-name-prefix = "SpkrLeft";
>> +		#thermal-sensor-cells = <0>;
>> +		vdd-supply = <&vreg_l18b_1p8>;
>> +		qcom,port-mapping = <1 2 3 7>;
>> +	};
>> +
>> +	right_spkr: speaker@0,2 {
>> +		compatible = "sdw10217020200";
>> +		reg = <0 2>;
>> +		powerdown-gpios = <&tlmm 158 GPIO_ACTIVE_LOW>;
>> +		#sound-dai-cells = <0>;
>> +		sound-name-prefix = "SpkrRight";
>> +		#thermal-sensor-cells = <0>;
>> +		vdd-supply = <&vreg_l18b_1p8>;
>> +		qcom,port-mapping = <4 5 6 8>;
>> +	};
>> +};
>> +
> 
> also, should we enable the soundwire controller?

ACK,
yes need to enable soundwire controller, Will take care to enable in 
next patchset version.

Thanks,
Prasad

> 
>>   &tlmm {
>>   	gpio-reserved-ranges = <32 2>, /* ADSP */
>>   			       <48 4>; /* NFC */
>> -- 
>> 2.34.1
>>

[PATCH v1 5/8] arm64: dts: qcom: qcs6490-rb3gen2: Add sound card

[Prasad Kumpatla]

From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>

Add the sound card node with tested playback over WSA8835 speakers
and msm mics.

Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
---
 arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 80 ++++++++++++++++++++
 1 file changed, 80 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
index a1a3df77ad57..5d4d3df6eff9 100644
--- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
+++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
@@ -219,6 +219,56 @@ vph_pwr: vph-pwr-regulator {
 		regulator-min-microvolt = <3700000>;
 		regulator-max-microvolt = <3700000>;
 	};
+
+	sound: sound {
+		compatible = "qcom,qcs6490-rb3gen2-sndcard";
+		model = "qcs6490-rb3gen2-snd-card";
+
+		audio-routing =
+			"SpkrLeft IN", "WSA_SPK1 OUT",
+			"SpkrRight IN", "WSA_SPK2 OUT",
+			"VA DMIC0", "vdd-micb",
+			"VA DMIC1", "vdd-micb",
+			"VA DMIC2", "vdd-micb",
+			"VA DMIC3", "vdd-micb";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+		wsa-dai-link {
+			link-name = "CODEC_DMA-LPAIF_WSA-RX-0";
+
+			cpu {
+				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+			};
+
+			codec {
+				sound-dai = <&left_spkr>, <&right_spkr>, <&swr2 0>,
+					    <&lpass_wsa_macro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		va-dai-link {
+			link-name = "CODEC_DMA-LPAIF_VA-TX-0";
+
+			cpu {
+				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+			};
+
+			codec {
+				sound-dai = <&lpass_va_macro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+	};
+
 };
 
 &apps_rsc {
@@ -697,6 +747,36 @@ &lpass_wsa_macro {
 	status = "okay";
 };
 
+&lpass_dmic01_clk {
+	drive-strength = <8>;
+	bias-disable;
+};
+
+&lpass_dmic01_data {
+	bias-pull-down;
+};
+
+&lpass_dmic23_clk {
+	drive-strength = <8>;
+	bias-disable;
+};
+
+&lpass_dmic23_data {
+	bias-pull-down;
+};
+
+&lpass_wsa_swr_clk {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-disable;
+};
+
+&lpass_wsa_swr_data {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-bus-hold;
+};
+
 &mdss {
 	status = "okay";
 };
-- 
2.34.1

Re: [PATCH v1 5/8] arm64: dts: qcom: qcs6490-rb3gen2: Add sound card

[Konrad Dybcio]

On 3/17/25 6:41 AM, Prasad Kumpatla wrote:
> From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
> 
> Add the sound card node with tested playback over WSA8835 speakers
> and msm mics.
> 
> Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
> Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
> Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
> ---
>  arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 80 ++++++++++++++++++++
>  1 file changed, 80 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> index a1a3df77ad57..5d4d3df6eff9 100644
> --- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> +++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> @@ -219,6 +219,56 @@ vph_pwr: vph-pwr-regulator {
>  		regulator-min-microvolt = <3700000>;
>  		regulator-max-microvolt = <3700000>;
>  	};
> +
> +	sound: sound {

The label is not used, please drop

> +		compatible = "qcom,qcs6490-rb3gen2-sndcard";
> +		model = "qcs6490-rb3gen2-snd-card";
> +
> +		audio-routing =

Please don't break the line here

> +			"SpkrLeft IN", "WSA_SPK1 OUT",
> +			"SpkrRight IN", "WSA_SPK2 OUT",
> +			"VA DMIC0", "vdd-micb",
> +			"VA DMIC1", "vdd-micb",
> +			"VA DMIC2", "vdd-micb",
> +			"VA DMIC3", "vdd-micb";
> +
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +		wsa-dai-link {
> +			link-name = "CODEC_DMA-LPAIF_WSA-RX-0";

Very unusual link name

> +
> +			cpu {
> +				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
> +			};
> +
> +			codec {
> +				sound-dai = <&left_spkr>, <&right_spkr>, <&swr2 0>,
> +					    <&lpass_wsa_macro 0>;
> +			};

'co'dec < 'cp'u


Konrad

Re: [PATCH v1 5/8] arm64: dts: qcom: qcs6490-rb3gen2: Add sound card

[Prasad Kumpatla]

On 4/2/2025 3:02 AM, Konrad Dybcio wrote:
> On 3/17/25 6:41 AM, Prasad Kumpatla wrote:
>> From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
>>
>> Add the sound card node with tested playback over WSA8835 speakers
>> and msm mics.
>>
>> Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
>> Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
>> Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
>> ---
>>   arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 80 ++++++++++++++++++++
>>   1 file changed, 80 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
>> index a1a3df77ad57..5d4d3df6eff9 100644
>> --- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
>> +++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
>> @@ -219,6 +219,56 @@ vph_pwr: vph-pwr-regulator {
>>   		regulator-min-microvolt = <3700000>;
>>   		regulator-max-microvolt = <3700000>;
>>   	};
>> +
>> +	sound: sound {
> 
> The label is not used, please drop

ACK,
Will fix it.

> 
>> +		compatible = "qcom,qcs6490-rb3gen2-sndcard";
>> +		model = "qcs6490-rb3gen2-snd-card";
>> +
>> +		audio-routing =
> 
> Please don't break the line here

Yes, Will update.

> 
>> +			"SpkrLeft IN", "WSA_SPK1 OUT",
>> +			"SpkrRight IN", "WSA_SPK2 OUT",
>> +			"VA DMIC0", "vdd-micb",
>> +			"VA DMIC1", "vdd-micb",
>> +			"VA DMIC2", "vdd-micb",
>> +			"VA DMIC3", "vdd-micb";
>> +
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +
>> +		wsa-dai-link {
>> +			link-name = "CODEC_DMA-LPAIF_WSA-RX-0";
> 
> Very unusual link name

ACK,
Will check and update.

> 
>> +
>> +			cpu {
>> +				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
>> +			};
>> +
>> +			codec {
>> +				sound-dai = <&left_spkr>, <&right_spkr>, <&swr2 0>,
>> +					    <&lpass_wsa_macro 0>;
>> +			};
> 
> 'co'dec < 'cp'u

ACK,
Will update in next patchset.

Thanks,
Prasad

> 
> 
> Konrad

[PATCH v1 6/8] arm64: dts: qcom: qcm6490-idp: Modify WSA/VA/RX/TX macro clock nodes for audioreach solution

[Prasad Kumpatla]

From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>

Modify and enable WSA, VA, RX and TX macro and lpass_tlmm clock properties.
For audioreach solution mclk, npl and fsgen clocks are enabled through
the q6prm clock driver.

Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
---
 arch/arm64/boot/dts/qcom/qcm6490-idp.dts | 57 ++++++++++++++++++++++++
 1 file changed, 57 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcm6490-idp.dts b/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
index 9209efcc49b5..5f994188bb0b 100644
--- a/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
+++ b/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
@@ -13,6 +13,7 @@
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
 #include "sc7280.dtsi"
 #include "pm7250b.dtsi"
 #include "pm7325.dtsi"
@@ -515,6 +516,62 @@ &gpu_zap_shader {
 	firmware-name = "qcom/qcm6490/a660_zap.mbn";
 };
 
+&lpass_rx_macro {
+	/delete-property/ power-domains;
+	/delete-property/ power-domain-names;
+	clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&q6prmcc LPASS_CLK_ID_TX_CORE_NPL_MCLK  LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&lpass_va_macro>;
+	clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
+
+	status = "okay";
+};
+
+&lpass_tlmm {
+	clocks = <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+	clock-names = "core", "audio";
+};
+
+&lpass_tx_macro {
+	/delete-property/ power-domains;
+	/delete-property/ power-domain-names;
+	clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&q6prmcc LPASS_CLK_ID_TX_CORE_NPL_MCLK  LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&lpass_va_macro>;
+	clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
+
+	status = "okay";
+};
+
+&lpass_va_macro {
+	/delete-property/ power-domains;
+	/delete-property/ power-domain-names;
+	clocks = <&q6prmcc LPASS_CLK_ID_VA_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+	clock-names = "mclk", "macro", "dcodec";
+
+	status = "okay";
+};
+
+&lpass_wsa_macro {
+	/delete-property/ power-domains;
+	/delete-property/ power-domain-names;
+	clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&q6prmcc LPASS_CLK_ID_TX_CORE_NPL_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+		 <&lpass_va_macro>;
+	clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
+
+	status = "okay";
+};
+
 &mdss {
 	status = "okay";
 };
-- 
2.34.1

[PATCH v1 7/8] arm64: dts: qcom: qcm6490-idp: Add WSA8830 speakers amplifier and WCD9370 headset codec

[Prasad Kumpatla]

From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>

Add nodes for WSA8830 speakers amplifier and WCD9370 headset codec
on qcm6490-idp board.

Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
---
 arch/arm64/boot/dts/qcom/qcm6490-idp.dts | 83 ++++++++++++++++++++++++
 1 file changed, 83 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcm6490-idp.dts b/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
index 5f994188bb0b..cbe11c6b6672 100644
--- a/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
+++ b/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
@@ -170,6 +170,30 @@ vph_pwr: vph-pwr-regulator {
 		regulator-min-microvolt = <3700000>;
 		regulator-max-microvolt = <3700000>;
 	};
+
+	wcd9370: audio-codec-0 {
+		compatible = "qcom,wcd9370-codec";
+
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&wcd_reset_n>;
+		pinctrl-1 = <&wcd_reset_n_sleep>;
+
+		reset-gpios = <&tlmm 83 GPIO_ACTIVE_HIGH>;
+
+		vdd-buck-supply = <&vreg_l17b_1p7>;
+		vdd-rxtx-supply = <&vreg_l18b_1p8>;
+		vdd-px-supply = <&vreg_l18b_1p8>;
+		vdd-mic-bias-supply = <&vreg_bob_3p296>;
+
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+
+		qcom,rx-device = <&wcd937x_rx>;
+		qcom,tx-device = <&wcd937x_tx>;
+
+		#sound-dai-cells = <1>;
+	};
 };
 
 &apps_rsc {
@@ -729,6 +753,30 @@ &sdc2_data {
 	drive-strength = <10>;
 };
 
+&swr2 {
+	left_spkr: speaker@0,1 {
+		compatible = "sdw10217020200";
+		reg = <0 1>;
+		powerdown-gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrLeft";
+		#thermal-sensor-cells = <0>;
+		vdd-supply = <&vreg_l18b_1p8>;
+		qcom,port-mapping = <1 2 3 7>;
+	};
+
+	right_spkr: speaker@0,2 {
+		compatible = "sdw10217020200";
+		reg = <0 2>;
+		powerdown-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrRight";
+		#thermal-sensor-cells = <0>;
+		vdd-supply = <&vreg_l18b_1p8>;
+		qcom,port-mapping = <4 5 6 8>;
+	};
+};
+
 &sdhc_1 {
 	non-removable;
 	no-sd;
@@ -752,6 +800,22 @@ &sdhc_2 {
 	cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>;
 };
 
+&swr0 {
+	wcd937x_rx: codec@0,4 {
+		compatible = "sdw20217010a00";
+		reg = <0 4>;
+		qcom,rx-port-mapping = <1 2 3 4 5>;
+	};
+};
+
+&swr1 {
+	wcd937x_tx: codec@0,3 {
+		compatible = "sdw20217010a00";
+		reg = <0 3>;
+		qcom,tx-port-mapping = <1 1 2 3>;
+	};
+};
+
 &tlmm {
 	gpio-reserved-ranges = <32 2>, /* ADSP */
 			       <48 4>; /* NFC */
@@ -761,6 +825,25 @@ sd_cd: sd-cd-state {
 		function = "gpio";
 		bias-pull-up;
 	};
+
+	sw_ctrl: sw-ctrl-state {
+		pins = "gpio86";
+		function = "gpio";
+		bias-pull-down;
+	};
+
+	wcd_reset_n: wcd-reset-n-state {
+		pins = "gpio83";
+		function = "gpio";
+		drive-strength = <8>;
+	};
+
+	wcd_reset_n_sleep: wcd-reset-n-sleep-state {
+		pins = "gpio83";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
 };
 
 &uart5 {
-- 
2.34.1

[PATCH v1 8/8] arm64: dts: qcom: qcm6490-idp: Add sound card

[Prasad Kumpatla]

From: Mohammad Rafi Shaik <quic_mohs@quicinc.com>

Add the sound card node with tested playback over WSA8835 speakers,
msm mic along with wcd9370 headset playabck and record.

Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
---
 arch/arm64/boot/dts/qcom/qcm6490-idp.dts | 142 +++++++++++++++++++++++
 1 file changed, 142 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcm6490-idp.dts b/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
index cbe11c6b6672..1c8b82bf6c1a 100644
--- a/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
+++ b/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
@@ -164,6 +164,94 @@ debug_vm_mem: debug-vm@d0600000 {
 		};
 	};
 
+	sound: sound {
+		compatible = "qcom,qcm6490-idp-sndcard";
+		model = "qcm6490-idp-snd-card";
+
+		audio-routing =
+			"SpkrLeft IN", "WSA_SPK1 OUT",
+			"SpkrRight IN", "WSA_SPK2 OUT",
+			"IN1_HPHL", "HPHL_OUT",
+			"IN2_HPHR", "HPHR_OUT",
+			"AMIC2", "MIC BIAS2",
+			"TX DMIC0", "MIC BIAS1",
+			"TX DMIC1", "MIC BIAS2",
+			"TX DMIC2", "MIC BIAS3",
+			"TX SWR_ADC1", "ADC2_OUTPUT",
+			"VA DMIC0", "VA MIC BIAS3",
+			"VA DMIC1", "VA MIC BIAS3",
+			"VA DMIC2", "VA MIC BIAS1",
+			"VA DMIC3", "VA MIC BIAS1";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+		wsa-dai-link {
+			link-name = "CODEC_DMA-LPAIF_WSA-RX-0";
+
+			cpu {
+				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+			};
+
+			codec {
+				sound-dai = <&left_spkr>, <&right_spkr>, <&swr2 0>,
+					    <&lpass_wsa_macro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wcd-playback-dai-link {
+			link-name = "CODEC_DMA-LPAIF_RXTX-RX-0";
+
+			cpu {
+				sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+			};
+
+			codec {
+				sound-dai = <&wcd9370 0>, <&swr0 0>, <&lpass_rx_macro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wcd-capture-dai-link {
+			link-name = "CODEC_DMA-LPAIF_RXTX-TX-3";
+
+			cpu {
+				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+			};
+
+			codec {
+				sound-dai = <&wcd9370 1>, <&swr1 0>, <&lpass_tx_macro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		va-dai-link {
+			link-name = "CODEC_DMA-LPAIF_VA-TX-0";
+
+			cpu {
+				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+			};
+
+			codec {
+				sound-dai = <&lpass_va_macro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+	};
+
 	vph_pwr: vph-pwr-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vph_pwr";
@@ -596,6 +684,60 @@ &lpass_wsa_macro {
 	status = "okay";
 };
 
+&lpass_dmic01_clk {
+	drive-strength = <8>;
+	bias-disable;
+};
+
+&lpass_dmic01_data {
+	bias-pull-down;
+};
+
+&lpass_dmic23_clk {
+	drive-strength = <8>;
+	bias-disable;
+};
+
+&lpass_dmic23_data {
+	bias-pull-down;
+};
+
+&lpass_rx_swr_clk {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-disable;
+};
+
+&lpass_rx_swr_data {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-bus-hold;
+};
+
+&lpass_tx_swr_clk {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-disable;
+};
+
+&lpass_tx_swr_data {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-bus-hold;
+};
+
+&lpass_wsa_swr_clk {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-disable;
+};
+
+&lpass_wsa_swr_data {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-bus-hold;
+};
+
 &mdss {
 	status = "okay";
 };
-- 
2.34.1

Re: [PATCH v1 8/8] arm64: dts: qcom: qcm6490-idp: Add sound card

[Bryan O'Donoghue]

On 17/03/2025 05:41, Prasad Kumpatla wrote:
> Add the sound card node with tested playback over WSA8835 speakers,
> msm mic along with wcd9370 headset playabck and record.

I think as a reviewer I'd like a better description.

"msm mic" doesn't mean much - please specify the number of MICs and 
their type - "four digital mics"

MSM Mics are not a meaningful description.

---
bod

Re: [PATCH v1 8/8] arm64: dts: qcom: qcm6490-idp: Add sound card

[Prasad Kumpatla]

On 3/27/2025 4:42 AM, Bryan O'Donoghue wrote:
> On 17/03/2025 05:41, Prasad Kumpatla wrote:
>> Add the sound card node with tested playback over WSA8835 speakers,
>> msm mic along with wcd9370 headset playabck and record.
> 
> I think as a reviewer I'd like a better description.
> 
> "msm mic" doesn't mean much - please specify the number of MICs and 
> their type - "four digital mics"
> 
> MSM Mics are not a meaningful description.

ACK,
Will provide proper description in next patchset version.

Thanks,
Prasad>
> ---
> bod