[PATCH v3 0/2] regulator: add support for SGM3804 Dual Output driver

[PATCH v3 0/2] regulator: add support for SGM3804 Dual Output driver

[Neil Armstrong]

Add support for the SG Micro SGM3804 Single Inductor Dual Output
Buck/Boost Converter used to power LCD panels a provide positive
and negative power rails with configurable voltage and active
discharge function for each output.

The SGM3804 is powered by the enable GPIO pins inputs and only
supports I2C write messages. 
In order to add flexibility and simplify the driver, the
regmap cache is enabled and populated with default values
since we can't write registers when the 2 GPIOs are down.

This regulator is used to provide vsn and vsn power to the
Ayaneo Pocket S2 dual-DSI LCD panel.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
Changes in v3:
- Change header in c++ comment block
- Switch to regcache dirty/only instead of custom handling
- Use GPIO_ASIS to avoid turning off regulator on boot
- Use gpio cansleep
- Add my MODULE_AUTHOR and reorder the signoff
- Link to v2: https://patch.msgid.link/20260430-topic-sm8650-ayaneo-pocket-s2-sgm3804-v2-0-76108c65a560@linaro.org

Changes in v2:
- Fixed bindings subject and gpios minItems
- Fixed regulator signed-off order
- Added second MODULE_AUTHOR entry
- Added more comments on how regmap cache is configured to work
- Link to v1: https://patch.msgid.link/20260428-topic-sm8650-ayaneo-pocket-s2-sgm3804-v1-0-1d8dc7620256@linaro.org

---
KancyJoe (1):
      regulator: add SGM3804 Dual Output driver

Neil Armstrong (1):
      regulator: dt-bindings: document the SGM3804 Dual Output regulator

 .../bindings/regulator/sgmicro,sgm3804.yaml        |  77 ++++++
 drivers/regulator/Kconfig                          |   7 +
 drivers/regulator/Makefile                         |   1 +
 drivers/regulator/sgm3804-regulator.c              | 297 +++++++++++++++++++++
 4 files changed, 382 insertions(+)
---
base-commit: 39704f00f747aba3144289870b5fd8ac230a9aaf
change-id: 20260428-topic-sm8650-ayaneo-pocket-s2-sgm3804-8764fbb72eb7

Best regards,
--  
Neil Armstrong <neil.armstrong@linaro.org>

[PATCH v3 1/2] regulator: dt-bindings: document the SGM3804 Dual Output regulator

[Neil Armstrong]

Document the SG Micro SGM3804 Single Inductor Dual Output Buck/Boost
Converter used to power LCD panels a provide positive and negative
power rails with configurable voltage and active discharge function
for each output.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 .../bindings/regulator/sgmicro,sgm3804.yaml        | 77 ++++++++++++++++++++++
 1 file changed, 77 insertions(+)

diff --git a/Documentation/devicetree/bindings/regulator/sgmicro,sgm3804.yaml b/Documentation/devicetree/bindings/regulator/sgmicro,sgm3804.yaml
new file mode 100644
index 000000000000..5ea475f8f8b6
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/sgmicro,sgm3804.yaml
@@ -0,0 +1,77 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/sgmicro,sgm3804.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SG Micro SGM3804 Single Inductor Dual Output Buck/Boost Converter
+
+maintainers:
+  - Neil Armstrong <neil.armstrong@linaro.org>
+
+description:
+  The SGM3804 is a dual voltage regulator, designed to support positive/negative
+  supply for driving LCD panels. It support software-configurable output
+  switching. The output voltages can be programmed via an I2C compatible interface.
+
+properties:
+  compatible:
+    const: sgmicro,sgm3804
+
+  reg:
+    maxItems: 1
+
+  enable-gpios:
+    minItems: 2
+    description:
+      GPIO specifiers to enable the positive and negative outputs.
+
+  vin-supply: true
+
+patternProperties:
+  "^(pos|neg)$":
+    type: object
+    $ref: regulator.yaml#
+    unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - enable-gpios
+  - pos
+  - neg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        regulator@3e {
+            compatible = "sgmicro,sgm3804";
+            reg = <0x3e>;
+
+            vin-supply = <&vin_reg>;
+
+            enable-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>,
+                           <&gpio 18 GPIO_ACTIVE_HIGH>;
+
+            pos {
+                regulator-name = "outpos";
+                regulator-min-microvolt = <5000000>;
+                regulator-max-microvolt = <5000000>;
+            };
+
+            neg {
+                regulator-name = "outneg";
+                regulator-min-microvolt = <5000000>;
+                regulator-max-microvolt = <5000000>;
+            };
+        };
+    };
+...
+

-- 
2.34.1

[PATCH v3 2/2] regulator: add SGM3804 Dual Output driver

[Neil Armstrong]

From: KancyJoe <kancy2333@outlook.com>

Add support for the SG Micro SGM3804 Single Inductor Dual Output
Buck/Boost Converter used to power LCD panels a provide positive
and negative power rails with configurable voltage and active
discharge function for each output.

The SGM3804 is powered by the enable GPIO pins inputs and only
supports I2C write messages.
In order to add flexibility and simplify the driver, the
regmap cache is enabled and populated with default values
since we can't write registers when the 2 GPIOs are down.

Signed-off-by: KancyJoe <kancy2333@outlook.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 drivers/regulator/Kconfig             |   7 +
 drivers/regulator/Makefile            |   1 +
 drivers/regulator/sgm3804-regulator.c | 297 ++++++++++++++++++++++++++++++++++
 3 files changed, 305 insertions(+)

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index e8002526cfb0..9335c1bd0c5b 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -1590,6 +1590,13 @@ config REGULATOR_SUN20I
 	help
 	  This driver supports the internal LDOs in the Allwinner D1 SoC.
 
+config REGULATOR_SGM3804
+	tristate "SGMicro SGM3804 voltage regulator"
+	depends on I2C && OF
+	select REGMAP_I2C
+	help
+	  This driver supports SGMicro SGM3804 dual-output voltage regulator.
+
 config REGULATOR_SY7636A
 	tristate "Silergy SY7636A voltage regulator"
 	depends on MFD_SY7636A
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 35639f3115fd..7c345c7caee7 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -181,6 +181,7 @@ obj-$(CONFIG_REGULATOR_STM32_PWR) += stm32-pwr.o
 obj-$(CONFIG_REGULATOR_STPMIC1) += stpmic1_regulator.o
 obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o
 obj-$(CONFIG_REGULATOR_SUN20I) += sun20i-regulator.o
+obj-$(CONFIG_REGULATOR_SGM3804) += sgm3804-regulator.o
 obj-$(CONFIG_REGULATOR_SY7636A) += sy7636a-regulator.o
 obj-$(CONFIG_REGULATOR_SY8106A) += sy8106a-regulator.o
 obj-$(CONFIG_REGULATOR_SY8824X) += sy8824x.o
diff --git a/drivers/regulator/sgm3804-regulator.c b/drivers/regulator/sgm3804-regulator.c
new file mode 100644
index 000000000000..182dcf763afb
--- /dev/null
+++ b/drivers/regulator/sgm3804-regulator.c
@@ -0,0 +1,297 @@
+// SPDX-License-Identifier: GPL-2.0-only
+//
+// SGMicro SGM3804 regulator Driver
+//
+// Copyright (C) 2025 Kancy Joe <kancy2333@outlook.com>
+// Copyright (C) 2026 Linaro Limited
+// Author: Neil Armstrong <neil.armstrong@linaro.org>
+
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/gpio/consumer.h>
+
+#define SGM3804_POS_RAIL_VOLTAGE_REG	0x0
+#define SGM3804_NEG_RAIL_VOLTAGE_REG	0x1
+#define SGM3804_RAIL_DISCHARGE_REG	0x3
+
+#define RAIL_VOLTAGE_MASK	GENMASK(5, 0)
+
+#define POS_RAIL_DISCHARGE_EN	BIT(1)
+#define NEG_RAIL_DISCHARGE_EN	BIT(0)
+
+#define RAIL_VOLTAGE_INVALID		RAIL_VOLTAGE_MASK
+#define RAIL_DISCHARGE_REG_DEFAULT	(POS_RAIL_DISCHARGE_EN | NEG_RAIL_DISCHARGE_EN)
+
+#define SGM3804_VOLTAGES_COUNT	40
+
+enum {
+	SGM3804_POS_RAIL = 0,
+	SGM3804_NEG_RAIL,
+	SGM3804_RAIL_COUNT,
+};
+
+/*
+ * The registers are only writable when the gpio is enabled, so
+ * we need to use the cache for read operations and set the regmap
+ * as cache_only when both GPIOs are down.
+ */
+struct sgm3804_data {
+	struct regmap *regmap;
+	/* Protects the regcache state update */
+	struct mutex lock;
+	struct gpio_desc *gpios[SGM3804_RAIL_COUNT];
+};
+
+static const struct linear_range sgm3804_voltages[] = {
+	REGULATOR_LINEAR_RANGE(2400000, 0x20, 0x2f, 100000),
+	REGULATOR_LINEAR_RANGE(4000000, 0x00, 0x17, 100000),
+};
+
+/*
+ * The cache is populated with those hardware default values
+ * so the regmap_update_bits operation will use the cached
+ * value to build a new register value and write it when GPIOs
+ * are enabled.
+ */
+static const struct reg_default sgm3804_reg_defaults[] = {
+	{ SGM3804_POS_RAIL_VOLTAGE_REG, RAIL_VOLTAGE_INVALID },
+	{ SGM3804_NEG_RAIL_VOLTAGE_REG, RAIL_VOLTAGE_INVALID },
+	{ SGM3804_RAIL_DISCHARGE_REG, RAIL_DISCHARGE_REG_DEFAULT },
+};
+
+/* Registers are only writable */
+static bool sgm3804_writeable_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case SGM3804_POS_RAIL_VOLTAGE_REG:
+	case SGM3804_NEG_RAIL_VOLTAGE_REG:
+	case SGM3804_RAIL_DISCHARGE_REG:
+		return true;
+	default:
+		return false;
+	}
+}
+
+/*
+ * Since all registers are only writeable, regmap will only read from the cache data.
+ */
+static bool sgm3804_readable_reg(struct device *dev, unsigned int reg)
+{
+	return false;
+}
+
+static const struct regmap_config sgm3804_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = 0x03,
+	.writeable_reg = sgm3804_writeable_reg,
+	.readable_reg = sgm3804_readable_reg,
+	.cache_type = REGCACHE_MAPLE,
+	.reg_defaults = sgm3804_reg_defaults,
+	.num_reg_defaults = ARRAY_SIZE(sgm3804_reg_defaults),
+};
+
+static int sgm3804_sync_regcache_state(struct sgm3804_data *ctx)
+{
+	guard(mutex)(&ctx->lock);
+
+	/* If both GPIOs are down, IC is powered down and I2C writes will fail */
+	if (!gpiod_get_value_cansleep(ctx->gpios[SGM3804_POS_RAIL]) &&
+	    !gpiod_get_value_cansleep(ctx->gpios[SGM3804_NEG_RAIL])) {
+		regcache_cache_only(ctx->regmap, true);
+		regcache_mark_dirty(ctx->regmap);
+	} else {
+		/* At least a GPIO is up, we can write registers */
+		regcache_cache_only(ctx->regmap, false);
+		return regcache_sync(ctx->regmap);
+	}
+
+	return 0;
+}
+
+static int sgm3804_get_voltage_sel(struct regulator_dev *rdev)
+{
+	int ret;
+
+	ret = regulator_get_voltage_sel_regmap(rdev);
+	if (ret < 0)
+		return ret;
+
+	/* Force setting a voltage on probe */
+	if (ret == RAIL_VOLTAGE_INVALID)
+		return -ENOTRECOVERABLE;
+
+	return ret;
+}
+
+static int sgm3804_enable(struct regulator_dev *rdev)
+{
+	struct sgm3804_data *ctx = rdev->reg_data;
+	int ret;
+
+	ret = gpiod_set_value_cansleep(ctx->gpios[rdev_get_id(rdev)], 1);
+	if (ret)
+		return ret;
+
+	ret = sgm3804_sync_regcache_state(ctx);
+	if (ret)
+		goto err;
+
+	return 0;
+
+err:
+	gpiod_set_value(ctx->gpios[rdev_get_id(rdev)], 0);
+	return ret;
+}
+
+static int sgm3804_disable(struct regulator_dev *rdev)
+{
+	struct sgm3804_data *ctx = rdev->reg_data;
+	int ret;
+
+	ret = gpiod_set_value_cansleep(ctx->gpios[rdev_get_id(rdev)], 0);
+	if (ret)
+		return ret;
+
+	return sgm3804_sync_regcache_state(ctx);
+}
+
+static int sgm3804_is_enabled(struct regulator_dev *rdev)
+{
+	struct sgm3804_data *ctx = rdev->reg_data;
+
+	return gpiod_get_value_cansleep(ctx->gpios[rdev_get_id(rdev)]);
+}
+
+static const struct regulator_ops sgm3804_ops = {
+	.list_voltage = regulator_list_voltage_linear_range,
+	.map_voltage = regulator_map_voltage_linear_range,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = sgm3804_get_voltage_sel,
+	.set_active_discharge = regulator_set_active_discharge_regmap,
+	.enable = sgm3804_enable,
+	.disable = sgm3804_disable,
+	.is_enabled = sgm3804_is_enabled,
+};
+
+static const struct regulator_desc sgm3804_regulator_desc[] = {
+	/* Positive Output */
+	{
+		.name = "pos",
+		.of_match = "pos",
+		.supply_name = "vin",
+		.id = SGM3804_POS_RAIL,
+		.ops = &sgm3804_ops,
+		.type = REGULATOR_VOLTAGE,
+		.linear_ranges = sgm3804_voltages,
+		.n_linear_ranges = ARRAY_SIZE(sgm3804_voltages),
+		.n_voltages = SGM3804_VOLTAGES_COUNT,
+		.vsel_reg = SGM3804_POS_RAIL_VOLTAGE_REG,
+		.vsel_mask = RAIL_VOLTAGE_MASK,
+		.active_discharge_on = POS_RAIL_DISCHARGE_EN,
+		.active_discharge_mask = POS_RAIL_DISCHARGE_EN,
+		.active_discharge_reg = SGM3804_RAIL_DISCHARGE_REG,
+		.enable_time = 40000,
+		.owner = THIS_MODULE,
+	},
+	/* Negative Output */
+	{
+		.name = "neg",
+		.of_match = "neg",
+		.supply_name = "vin",
+		.id = SGM3804_NEG_RAIL,
+		.ops = &sgm3804_ops,
+		.type = REGULATOR_VOLTAGE,
+		.linear_ranges = sgm3804_voltages,
+		.n_linear_ranges = ARRAY_SIZE(sgm3804_voltages),
+		.n_voltages = SGM3804_VOLTAGES_COUNT,
+		.vsel_reg = SGM3804_NEG_RAIL_VOLTAGE_REG,
+		.vsel_mask = RAIL_VOLTAGE_MASK,
+		.active_discharge_on = NEG_RAIL_DISCHARGE_EN,
+		.active_discharge_mask = NEG_RAIL_DISCHARGE_EN,
+		.active_discharge_reg = SGM3804_RAIL_DISCHARGE_REG,
+		.enable_time = 40000,
+		.owner = THIS_MODULE,
+	},
+};
+
+static int sgm3804_probe(struct i2c_client *i2c)
+{
+	struct device *dev = &i2c->dev;
+	struct sgm3804_data *ctx;
+	int ret, i;
+
+	ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+
+	mutex_init(&ctx->lock);
+
+	ctx->regmap = devm_regmap_init_i2c(i2c, &sgm3804_regmap_config);
+	if (IS_ERR(ctx->regmap))
+		return dev_err_probe(dev, PTR_ERR(ctx->regmap),
+				     "failed to init regmap\n");
+
+	/* Set default values */
+	for (i = 0; i < ARRAY_SIZE(sgm3804_regulator_desc); i++) {
+		ctx->gpios[i] = devm_gpiod_get_index(dev, "enable",
+						     i, GPIOD_ASIS);
+		if (IS_ERR(ctx->gpios[i]))
+			return dev_err_probe(dev, PTR_ERR(ctx->gpios[i]),
+					"failed to get enable GPIO %d\n", i);
+	}
+
+	ret = sgm3804_sync_regcache_state(ctx);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < ARRAY_SIZE(sgm3804_regulator_desc); i++) {
+		struct regulator_config config = { };
+		struct regulator_dev *rdev;
+
+		config.dev = dev;
+		config.regmap = ctx->regmap;
+		config.of_node = dev->of_node;
+		config.driver_data = ctx;
+		rdev = devm_regulator_register(dev, &sgm3804_regulator_desc[i],
+					       &config);
+		if (IS_ERR(rdev))
+			return dev_err_probe(dev, PTR_ERR(rdev),
+					     "failed to register regulator %d\n", i);
+	}
+
+	return 0;
+}
+
+static const struct i2c_device_id sgm3804_id[] = {
+	{ "sgm3804" },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, sgm3804_id);
+
+static const struct of_device_id sgm3804_of_match[] = {
+	{ .compatible = "sgmicro,sgm3804" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, sgm3804_of_match);
+
+static struct i2c_driver sgm3804_regulator_driver = {
+	.driver = {
+		.name = "sgm3804",
+		.probe_type = PROBE_PREFER_ASYNCHRONOUS,
+		.of_match_table = sgm3804_of_match,
+	},
+	.probe = sgm3804_probe,
+	.id_table = sgm3804_id,
+};
+
+module_i2c_driver(sgm3804_regulator_driver);
+
+MODULE_DESCRIPTION("SGMicro SGM3804 regulator Driver");
+MODULE_AUTHOR("Kancy Joe <kancy2333@outlook.com>");
+MODULE_AUTHOR("Neil Armstrong <neil.armstrong@linaro.org>");
+MODULE_LICENSE("GPL");

-- 
2.34.1

Re: [PATCH v3 1/2] regulator: dt-bindings: document the SGM3804 Dual Output regulator

[Neil Armstrong]

On 5/4/26 14:44, Neil Armstrong wrote:
> Document the SG Micro SGM3804 Single Inductor Dual Output Buck/Boost
> Converter used to power LCD panels a provide positive and negative
> power rails with configurable voltage and active discharge function
> for each output.
> 
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
>   .../bindings/regulator/sgmicro,sgm3804.yaml        | 77 ++++++++++++++++++++++
>   1 file changed, 77 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/regulator/sgmicro,sgm3804.yaml b/Documentation/devicetree/bindings/regulator/sgmicro,sgm3804.yaml
> new file mode 100644
> index 000000000000..5ea475f8f8b6
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/regulator/sgmicro,sgm3804.yaml
> @@ -0,0 +1,77 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/regulator/sgmicro,sgm3804.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: SG Micro SGM3804 Single Inductor Dual Output Buck/Boost Converter
> +
> +maintainers:
> +  - Neil Armstrong <neil.armstrong@linaro.org>
> +
> +description:
> +  The SGM3804 is a dual voltage regulator, designed to support positive/negative
> +  supply for driving LCD panels. It support software-configurable output
> +  switching. The output voltages can be programmed via an I2C compatible interface.
> +
> +properties:
> +  compatible:
> +    const: sgmicro,sgm3804
> +
> +  reg:
> +    maxItems: 1
> +
> +  enable-gpios:
> +    minItems: 2
> +    description:
> +      GPIO specifiers to enable the positive and negative outputs.
> +
> +  vin-supply: true
> +
> +patternProperties:
> +  "^(pos|neg)$":
> +    type: object
> +    $ref: regulator.yaml#
> +    unevaluatedProperties: false
> +
> +required:
> +  - compatible
> +  - reg
> +  - enable-gpios
> +  - pos
> +  - neg
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +
> +    i2c {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        regulator@3e {
> +            compatible = "sgmicro,sgm3804";
> +            reg = <0x3e>;
> +
> +            vin-supply = <&vin_reg>;
> +
> +            enable-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>,
> +                           <&gpio 18 GPIO_ACTIVE_HIGH>;

So this fails with Rob's bot and with DTBS_CHECK with board DT but I can't make
it fail with dt_binding_check on my side.

enable-gpios: [[88, 59, 0], [88, 58, 0]] is too long

But I found out in Documentation/devicetree/bindings/gpio/gpio-consumer-common.yaml :
   enable-gpios:
     maxItems: 1
     description:
       GPIO connected to the enable control pin.

This was rather unexpected...

So I'll probably need update the bindings to mode the enable gpios in the subnodes instead.

Neil

> +
> +            pos {
> +                regulator-name = "outpos";
> +                regulator-min-microvolt = <5000000>;
> +                regulator-max-microvolt = <5000000>;
> +            };
> +
> +            neg {
> +                regulator-name = "outneg";
> +                regulator-min-microvolt = <5000000>;
> +                regulator-max-microvolt = <5000000>;
> +            };
> +        };
> +    };
> +...
> +
> 

Re: [PATCH v3 1/2] regulator: dt-bindings: document the SGM3804 Dual Output regulator

[Rob Herring (Arm)]

On Mon, 04 May 2026 14:44:05 +0200, Neil Armstrong wrote:
> Document the SG Micro SGM3804 Single Inductor Dual Output Buck/Boost
> Converter used to power LCD panels a provide positive and negative
> power rails with configurable voltage and active discharge function
> for each output.
> 
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
>  .../bindings/regulator/sgmicro,sgm3804.yaml        | 77 ++++++++++++++++++++++
>  1 file changed, 77 insertions(+)
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/regulator/sgmicro,sgm3804.example.dtb: regulator@3e (sgmicro,sgm3804): enable-gpios: [[4294967295, 17, 0], [4294967295, 18, 0]] is too long
	from schema $id: http://devicetree.org/schemas/gpio/gpio-consumer-common.yaml

doc reference errors (make refcheckdocs):

See https://patchwork.kernel.org/project/devicetree/patch/20260504-topic-sm8650-ayaneo-pocket-s2-sgm3804-v3-1-c4783443890b@linaro.org

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH v3 2/2] regulator: add SGM3804 Dual Output driver

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 335 bytes --]

On Mon, May 04, 2026 at 02:44:06PM +0200, Neil Armstrong wrote:

>  obj-$(CONFIG_REGULATOR_SUN20I) += sun20i-regulator.o
> +obj-$(CONFIG_REGULATOR_SGM3804) += sgm3804-regulator.o

The sorting is off here (and in Kconfig).

> +err:
> +	gpiod_set_value(ctx->gpios[rdev_get_id(rdev)], 0);
> +	return ret;

A stray gpiod_set_value() here.

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

Re: [PATCH v3 1/2] regulator: dt-bindings: document the SGM3804 Dual Output regulator

[Krzysztof Kozlowski]

On Mon, May 04, 2026 at 03:22:49PM +0200, Neil Armstrong wrote:
> On 5/4/26 14:44, Neil Armstrong wrote:
> > +        regulator@3e {
> > +            compatible = "sgmicro,sgm3804";
> > +            reg = <0x3e>;
> > +
> > +            vin-supply = <&vin_reg>;
> > +
> > +            enable-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>,
> > +                           <&gpio 18 GPIO_ACTIVE_HIGH>;
> 
> So this fails with Rob's bot and with DTBS_CHECK with board DT but I can't make
> it fail with dt_binding_check on my side.

Drop DT_SCHEMA_FILES and test against all bindings to reproduce this.

> 
> enable-gpios: [[88, 59, 0], [88, 58, 0]] is too long
> 
> But I found out in Documentation/devicetree/bindings/gpio/gpio-consumer-common.yaml :
>   enable-gpios:
>     maxItems: 1
>     description:
>       GPIO connected to the enable control pin.
> 
> This was rather unexpected...
> 
> So I'll probably need update the bindings to mode the enable gpios in the subnodes instead.
> 

Yes, if these GPIOs control specific regulators, convention is to put
them inside the regulator subnodes. Many other devices do it. This is a
bit different approach than with input supplies, which are supposed to
be put in top-level, even if they are dedicated to specific regulators.


Best regards,
Krzysztof