[PATCH v5 0/6] arm64: dts: qcom: Support AYN QCS8550 Devices

[PATCH v5 0/6] arm64: dts: qcom: Support AYN QCS8550 Devices

[Aaron Kling via B4 Relay]

This specifically includes:
* Odin 2 Mini
* Odin 2 Portal
* Thor

The original Odin 2 dts is not currently included as it has not yet
been verified.

The initial port was done by Teguh Sobirin for ROCKNIX and was made
available on the AYN github [0].

Support has been removed for things not yet supported by the upstream
kernel, these will be added later when the related drivers are submitted
and picked up. Such includes:

* All panels
* The Odin 2 Mini backlight and touch
* All rgb leds
* The built-in uart gamepad

[0] https://github.com/AYNTechnologies/linux/commits/sm8550/v6.17.5/

Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
---
Changes in v5:
- Fix some style reviews in patch 6 which required matching labels in
  patch 3
- Drop hdmi support in patch 4, since it doesn't work
- Link to v4: https://lore.kernel.org/r/20260323-ayn-qcs8550-v4-0-33a8ac3d53fa@gmail.com

Changes in v4:
- Fold vendor description patch into the series
- Link to v3: https://lore.kernel.org/r/20260322-ayn-qcs8550-v3-0-4afa89c20888@gmail.com

Changes in v3:
- Drop unused backlight regulator in patch 3
- Move zap shader firmware to standalone reference
- Move i2c controller enables from common to devices
- Add ABL dtbo workarounds to patch 2 as per:
  https://lore.kernel.org/linux-arm-msm/dczz4uvcq4hc6p3zb6xnrsgmfeomwliagwhf36tewdz4z6mndp@afbxzhjziiwv/
- Fix multiple property alphabetical order issues in patch 2
- Use interrupts-extended for pwm-fan in patch 2
- Ensure blank line before status in patches 2-5
- Rename spk_amp_l/r to amplifier in patch 2
- Remove a few properties that are already in the soc dtsi in patch 2
- Order tlmm nodes by pin index in patch 2
- Drop qcom,dll-config from sdhc node in patch 2
- Drop dtbo support, convert common to dtsi, and include it directly in
  device specific dts'
- Link to v2: https://lore.kernel.org/r/20260311-ayn-qcs8550-v2-0-e66986e0f0cb@gmail.com

Changes in v2:
- Drop awinic bindings dep as a duplicated patch already exists
- Change Co-authored-by tags to Co-developed-by
- Drop alias to currently unused uart15 in patch 2
- Link to v1: https://lore.kernel.org/r/20260311-ayn-qcs8550-v1-0-fe8b2faad1ea@gmail.com

---
Aaron Kling (1):
      dt-bindings: arm: qcom: Add AYN QCS8550 Devices

Teguh Sobirin (4):
      arm64: dts: qcom: Add AYN QCS8550 Common
      arm64: dts: qcom: Add AYN Odin 2 Mini
      arm64: dts: qcom: Add AYN Odin 2 Portal
      arm64: dts: qcom: Add AYN Thor

Xilin Wu (1):
      dt-bindings: vendor-prefixes: Add AYN Technologies

 Documentation/devicetree/bindings/arm/qcom.yaml    |    9 +
 .../devicetree/bindings/vendor-prefixes.yaml       |    2 +
 arch/arm64/boot/dts/qcom/Makefile                  |    3 +
 .../arm64/boot/dts/qcom/qcs8550-ayntec-common.dtsi | 1762 ++++++++++++++++++++
 .../boot/dts/qcom/qcs8550-ayntec-odin2mini.dts     |   44 +
 .../boot/dts/qcom/qcs8550-ayntec-odin2portal.dts   |   84 +
 arch/arm64/boot/dts/qcom/qcs8550-ayntec-thor.dts   |  227 +++
 7 files changed, 2131 insertions(+)
---
base-commit: db7efce4ae23ad5e42f5f55428f529ff62b86fab
change-id: 20260217-ayn-qcs8550-16c07b63de26

Best regards,
-- 
Aaron Kling <webgeek1234@gmail.com>

[PATCH v5 1/6] dt-bindings: vendor-prefixes: Add AYN Technologies

[Aaron Kling via B4 Relay]

From: Xilin Wu <wuxilin123@gmail.com>

Add an entry for AYN Technologies (https://www.ayntec.com/)

Signed-off-by: Xilin Wu <wuxilin123@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 28784d66ae7ba5..b891d6d41f198a 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -225,6 +225,8 @@ patternProperties:
     description: Axis Communications AB
   "^ayaneo,.*":
     description: Anyun Intelligent Technology (Hong Kong) Co., Ltd
+  "^ayntec,.*":
+    description: AYN Technologies Co., Ltd.
   "^azoteq,.*":
     description: Azoteq (Pty) Ltd
   "^azw,.*":

-- 
2.53.0

[PATCH v5 2/6] dt-bindings: arm: qcom: Add AYN QCS8550 Devices

[Aaron Kling via B4 Relay]

From: Aaron Kling <webgeek1234@gmail.com>

Namely:
* Odin 2
* Odin 2 Mini
* Odin 2 Portal
* Thor

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index b4943123d2e425..4a6733eaa8b14d 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -1099,6 +1099,15 @@ properties:
           - const: qcom,qcs8550
           - const: qcom,sm8550
 
+      - items:
+          - enum:
+              - ayntec,odin2
+              - ayntec,odin2mini
+              - ayntec,odin2portal
+              - ayntec,thor
+          - const: qcom,qcs8550
+          - const: qcom,sm8550
+
       - items:
           - enum:
               - ayaneo,pocket-s2

-- 
2.53.0

[PATCH v5 3/6] arm64: dts: qcom: Add AYN QCS8550 Common

[Aaron Kling via B4 Relay]

From: Teguh Sobirin <teguh@sobir.in>

This contains everything common between the AYN QCS8550 devices. It will
be included by device specific dts'.

Signed-off-by: Teguh Sobirin <teguh@sobir.in>
Co-developed-by: Aaron Kling <webgeek1234@gmail.com>
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
---
 .../arm64/boot/dts/qcom/qcs8550-ayntec-common.dtsi | 1762 ++++++++++++++++++++
 1 file changed, 1762 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs8550-ayntec-common.dtsi b/arch/arm64/boot/dts/qcom/qcs8550-ayntec-common.dtsi
new file mode 100644
index 00000000000000..e0befc8dc6dfdc
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs8550-ayntec-common.dtsi
@@ -0,0 +1,1762 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025, Teguh Sobirin.
+ */
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "qcs8550.dtsi"
+#include "pm8550.dtsi"
+#include "pm8550b.dtsi"
+#define PMK8550VE_SID 5
+#include "pm8550ve.dtsi"
+#include "pm8550vs.dtsi"
+#include "pmk8550.dtsi"
+
+/delete-node/ &aop_image_mem;
+/delete-node/ &aop_config_mem;
+/delete-node/ &camera_mem;
+/delete-node/ &ipa_fw_mem;
+/delete-node/ &ipa_gsi_mem;
+/delete-node/ &mpss_dsm_mem;
+/delete-node/ &mpss_mem;
+/delete-node/ &q6_mpss_dtb_mem;
+/delete-node/ &remoteproc_mpss;
+
+/ {
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &uart7;
+		serial1 = &uart14;
+	};
+
+	// The tzlog label is required by ABL to apply a dtbo, but it can be on any node
+	qcom_tzlog: chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&volume_up_n>;
+		pinctrl-names = "default";
+
+		key-volume-up {
+			label = "Volume Up";
+			debounce-interval = <15>;
+			gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+
+	pmic-glink {
+		compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_hs_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss_in: endpoint {
+						remote-endpoint = <&usb_dp_qmpphy_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_sbu: endpoint {
+						remote-endpoint = <&usb0_sbu_mux>;
+					};
+				};
+			};
+		};
+	};
+
+	pwm_fan: pwm-fan {
+		compatible = "pwm-fan";
+
+		fan-supply = <&vdd_fan_5v0>;
+		pwms = <&pm8550_pwm 3 50000>;
+
+		pinctrl-0 = <&fan_pwm_active>, <&fan_int>;
+		pinctrl-names = "default";
+
+		pulses-per-revolution = <4>;
+		interrupts-extended = <&tlmm 13 IRQ_TYPE_EDGE_FALLING>;
+
+		cooling-levels = <0 40 65 75 90 100 120 150 175>;
+		#cooling-cells = <2>;
+	};
+
+	reserved-memory {
+		hyp_mem: hyp-region@80000000 {
+			reg = <0 0x80000000 0 0xa00000>;
+			no-map;
+		};
+
+		cpusys_vm_mem: cpusys-vm-region@80a00000 {
+			reg = <0 0x80a00000 0 0x400000>;
+			no-map;
+		};
+
+		hyp_tags_mem: hyp-tags-region@80e00000 {
+			reg = <0 0x80e00000 0 0x3d0000>;
+			no-map;
+		};
+
+		xbl_sc_mem: xbl-sc-region@d8100000 {
+			reg = <0 0xd8100000 0 0x40000>;
+			no-map;
+		};
+
+		hyp_tags_reserved_mem: hyp-tags-reserved-region@811d0000 {
+			reg = <0 0x811d0000 0 0x30000>;
+			no-map;
+		};
+
+		xbl_dt_log_merged_mem: xbl-dt-log-merged-region@81a00000 {
+			reg = <0 0x81a00000 0 0x260000>;
+			no-map;
+		};
+
+		aop_config_merged_mem: aop-config-merged-region@81c80000 {
+			reg = <0 0x81c80000 0 0x74000>;
+			no-map;
+		};
+
+		chipinfo_mem: chipinfo-region@81cf4000 {
+			reg = <0 0x81cf4000 0 0x1000>;
+			no-map;
+		};
+
+		global_sync_mem: global-sync-region@82600000 {
+			reg = <0 0x82600000 0 0x100000>;
+			no-map;
+		};
+
+		tz_stat_mem: tz-stat-region@82700000 {
+			reg = <0 0x82700000 0 0x100000>;
+			no-map;
+		};
+
+		cpucp_fw_mem: cpucp-fw-region@d8140000 {
+			reg = <0 0xd8140000 0 0x1c0000>;
+			no-map;
+		};
+
+		qtee_mem: qtee-region@d8300000 {
+			reg = <0 0xd8300000 0 0x500000>;
+			no-map;
+		};
+
+		hwfence_shbuf: hwfence-shbuf-region@e6440000 {
+			reg = <0 0xe6440000 0 0x2dd000>;
+			no-map;
+		};
+
+		hyp_ext_reserved_mem: hyp-ext-reserved-region@ff700000 {
+			reg = <0 0xff700000 0 0x100000>;
+			no-map;
+		};
+
+		llcc_lpi_mem: llcc_lpi_region@ff800000 {
+			reg = <0 0xff800000 0 0x600000>;
+			no-map;
+		};
+
+		hyp_ext_tags_mem: hyp-ext-tags-region@fce00000 {
+			reg = <0 0xfce00000 0 0x2900000>;
+			no-map;
+		};
+	};
+
+	sound {
+		compatible = "qcom,sm8550-sndcard", "qcom,sm8450-sndcard";
+		pinctrl-0 = <&lpi_i2s3_active>;
+		pinctrl-names = "default";
+
+		model = "AYN-Odin2";
+		audio-routing = "IN1_HPHL", "HPHL_OUT",
+				"IN2_HPHR", "HPHR_OUT",
+				"AMIC2", "MIC BIAS2",
+				"TX SWR_INPUT1", "ADC2_OUTPUT";
+
+		speaker-i2s-dai-link {
+			link-name = "Primary MI2S Playback";
+
+			codec {
+				sound-dai = <&spk_amp_l>, <&spk_amp_r>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai PRIMARY_MI2S_RX>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wcd-playback-dai-link {
+			link-name = "WCD Playback";
+
+			codec {
+				sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wcd-capture-dai-link {
+			link-name = "WCD Capture";
+
+			codec {
+				sound-dai = <&wcd938x 1>, <&swr2 0>, <&lpass_txmacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		dp0-dai-link {
+			link-name = "DP0 Playback";
+
+			codec {
+				sound-dai = <&mdss_dp0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai DISPLAY_PORT_RX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+	};
+
+	thermal-zones {
+		cpu0-thermal {
+			polling-delay = <200>;
+
+			trips {
+				cpuss0_active0: cpu-active0 {
+					temperature = <50000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss0_active1: cpu-active1 {
+					temperature = <55000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss0_active2: cpu-active2 {
+					temperature = <60000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss0_active3: cpu-active3 {
+					temperature = <65000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss0_active4: cpu-active4 {
+					temperature = <70000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss0_active5: cpu-active5 {
+					temperature = <75000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss0_active6: cpu-active6 {
+					temperature = <80000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss0_active7: cpu-active7 {
+					temperature = <85000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					cooling-device = <&pwm_fan 0 1>;
+					trip = <&cpuss0_active0>;
+				};
+
+				map1 {
+					cooling-device = <&pwm_fan 1 2>;
+					trip = <&cpuss0_active1>;
+				};
+
+				map2 {
+					cooling-device = <&pwm_fan 2 3>;
+					trip = <&cpuss0_active2>;
+				};
+
+				map3 {
+					cooling-device = <&pwm_fan 3 4>;
+					trip = <&cpuss0_active3>;
+				};
+
+				map4 {
+					cooling-device = <&pwm_fan 4 5>;
+					trip = <&cpuss0_active4>;
+				};
+
+				map5 {
+					cooling-device = <&pwm_fan 5 6>;
+					trip = <&cpuss0_active5>;
+				};
+
+				map6 {
+					cooling-device = <&pwm_fan 6 7>;
+					trip = <&cpuss0_active6>;
+				};
+
+				map7 {
+					cooling-device = <&pwm_fan 7 8>;
+					trip = <&cpuss0_active7>;
+				};
+			};
+		};
+
+		cpu3-bottom-thermal {
+			polling-delay = <200>;
+
+			trips {
+				cpuss3_active0: cpu-active0 {
+					temperature = <50000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss3_active1: cpu-active1 {
+					temperature = <55000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss3_active2: cpu-active2 {
+					temperature = <60000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss3_active3: cpu-active3 {
+					temperature = <65000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss3_active4: cpu-active4 {
+					temperature = <70000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss3_active5: cpu-active5 {
+					temperature = <75000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss3_active6: cpu-active6 {
+					temperature = <80000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss3_active7: cpu-active7 {
+					temperature = <85000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					cooling-device = <&pwm_fan 0 1>;
+					trip = <&cpuss3_active0>;
+				};
+
+				map1 {
+					cooling-device = <&pwm_fan 1 2>;
+					trip = <&cpuss3_active1>;
+				};
+
+				map2 {
+					cooling-device = <&pwm_fan 2 3>;
+					trip = <&cpuss3_active2>;
+				};
+
+				map3 {
+					cooling-device = <&pwm_fan 3 4>;
+					trip = <&cpuss3_active3>;
+				};
+
+				map4 {
+					cooling-device = <&pwm_fan 4 5>;
+					trip = <&cpuss3_active4>;
+				};
+
+				map5 {
+					cooling-device = <&pwm_fan 5 6>;
+					trip = <&cpuss3_active5>;
+				};
+
+				map6 {
+					cooling-device = <&pwm_fan 6 7>;
+					trip = <&cpuss3_active6>;
+				};
+
+				map7 {
+					cooling-device = <&pwm_fan 7 8>;
+					trip = <&cpuss3_active7>;
+				};
+			};
+		};
+
+		cpu7-bottom-thermal {
+			polling-delay = <200>;
+
+			trips {
+				cpuss7_active0: cpu-active0 {
+					temperature = <50000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss7_active1: cpu-active1 {
+					temperature = <55000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss7_active2: cpu-active2 {
+					temperature = <60000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss7_active3: cpu-active3 {
+					temperature = <65000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss7_active4: cpu-active4 {
+					temperature = <70000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss7_active5: cpu-active5 {
+					temperature = <75000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss7_active6: cpu-active6 {
+					temperature = <80000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				cpuss7_active7: cpu-active7 {
+					temperature = <85000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					cooling-device = <&pwm_fan 0 1>;
+					trip = <&cpuss7_active0>;
+				};
+
+				map1 {
+					cooling-device = <&pwm_fan 1 2>;
+					trip = <&cpuss7_active1>;
+				};
+
+				map2 {
+					cooling-device = <&pwm_fan 2 3>;
+					trip = <&cpuss7_active2>;
+				};
+
+				map3 {
+					cooling-device = <&pwm_fan 3 4>;
+					trip = <&cpuss7_active3>;
+				};
+
+				map4 {
+					cooling-device = <&pwm_fan 4 5>;
+					trip = <&cpuss7_active4>;
+				};
+
+				map5 {
+					cooling-device = <&pwm_fan 5 6>;
+					trip = <&cpuss7_active5>;
+				};
+
+				map6 {
+					cooling-device = <&pwm_fan 6 7>;
+					trip = <&cpuss7_active6>;
+				};
+
+				map7 {
+					cooling-device = <&pwm_fan 7 8>;
+					trip = <&cpuss7_active7>;
+				};
+			};
+		};
+
+		gpuss-0-thermal {
+			polling-delay = <200>;
+
+			trips {
+				gpuss0_active0: gpu-active0 {
+					temperature = <50000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				gpuss0_active1: gpu-active1 {
+					temperature = <55000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				gpuss0_active2: gpu-active2 {
+					temperature = <60000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				gpuss0_active3: gpu-active3 {
+					temperature = <65000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				gpuss0_active4: gpu-active4 {
+					temperature = <70000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				gpuss0_active5: gpu-active5 {
+					temperature = <75000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				gpuss0_active6: gpu-active6 {
+					temperature = <80000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+
+				gpuss0_active7: gpu-active7 {
+					temperature = <85000>;
+					hysteresis = <4000>;
+					type = "active";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					cooling-device = <&pwm_fan 0 1>;
+					trip = <&gpuss0_active0>;
+				};
+
+				map1 {
+					cooling-device = <&pwm_fan 1 2>;
+					trip = <&gpuss0_active1>;
+				};
+
+				map2 {
+					cooling-device = <&pwm_fan 2 3>;
+					trip = <&gpuss0_active2>;
+				};
+
+				map3 {
+					cooling-device = <&pwm_fan 3 4>;
+					trip = <&gpuss0_active3>;
+				};
+
+				map4 {
+					cooling-device = <&pwm_fan 4 5>;
+					trip = <&gpuss0_active4>;
+				};
+
+				map5 {
+					cooling-device = <&pwm_fan 5 6>;
+					trip = <&gpuss0_active5>;
+				};
+
+				map6 {
+					cooling-device = <&pwm_fan 6 7>;
+					trip = <&gpuss0_active6>;
+				};
+
+				map7 {
+					cooling-device = <&pwm_fan 7 8>;
+					trip = <&gpuss0_active7>;
+				};
+			};
+		};
+	};
+
+	usb0-sbu-mux {
+		compatible = "pericom,pi3usb102", "gpio-sbu-mux";
+
+		enable-gpios = <&tlmm 140 GPIO_ACTIVE_LOW>;
+		select-gpios = <&tlmm 141 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&usb0_sbu_default>;
+		pinctrl-names = "default";
+
+		mode-switch;
+		orientation-switch;
+
+		port {
+			usb0_sbu_mux: endpoint {
+				remote-endpoint = <&pmic_glink_sbu>;
+			};
+		};
+	};
+
+	vdd_fan_5v0: vdd-fan-5v0-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_fan_5v0";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&tlmm 109 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&fan_pwr_active>;
+		pinctrl-names = "default";
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_mcu_3v3: vdd-mcu-3v3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_mcu_3v3";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+	};
+
+	vph_pwr: regulator-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	wcd938x: audio-codec {
+		compatible = "qcom,wcd9385-codec";
+
+		pinctrl-0 = <&wcd_default>;
+		pinctrl-names = "default";
+
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+		qcom,micbias4-microvolt = <1800000>;
+		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000
+							 500000 500000 500000 500000>;
+		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+		qcom,rx-device = <&wcd_rx>;
+		qcom,tx-device = <&wcd_tx>;
+
+		reset-gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
+
+		vdd-buck-supply = <&vreg_l15b_1p8>;
+		vdd-rxtx-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l15b_1p8>;
+		vdd-mic-bias-supply = <&vreg_bob1>;
+
+		#sound-dai-cells = <1>;
+	};
+
+	wcn7850-pmu {
+		compatible = "qcom,wcn7850-pmu";
+
+		pinctrl-0 = <&wlan_en>, <&bt_default>, <&pmk8550_sleep_clk>;
+		pinctrl-names = "default";
+
+		wlan-enable-gpios = <&tlmm 80 GPIO_ACTIVE_HIGH>;
+		bt-enable-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+
+		vdd-supply = <&vreg_s5g_0p8>;
+		vddio-supply = <&vreg_l15b_1p8>;
+		vddaon-supply = <&vreg_s2g_0p8>;
+		vdddig-supply = <&vreg_s4e_0p95>;
+		vddrfa1p2-supply = <&vreg_s4g_1p3>;
+		vddrfa1p8-supply = <&vreg_s6g_1p8>;
+
+		regulators {
+			vreg_pmu_rfa_cmn: ldo0 {
+				regulator-name = "vreg_pmu_rfa_cmn";
+			};
+
+			vreg_pmu_aon_0p59: ldo1 {
+				regulator-name = "vreg_pmu_aon_0p59";
+			};
+
+			vreg_pmu_wlcx_0p8: ldo2 {
+				regulator-name = "vreg_pmu_wlcx_0p8";
+			};
+
+			vreg_pmu_wlmx_0p85: ldo3 {
+				regulator-name = "vreg_pmu_wlmx_0p85";
+			};
+
+			vreg_pmu_btcmx_0p85: ldo4 {
+				regulator-name = "vreg_pmu_btcmx_0p85";
+			};
+
+			vreg_pmu_rfa_0p8: ldo5 {
+				regulator-name = "vreg_pmu_rfa_0p8";
+			};
+
+			vreg_pmu_rfa_1p2: ldo6 {
+				regulator-name = "vreg_pmu_rfa_1p2";
+			};
+
+			vreg_pmu_rfa_1p8: ldo7 {
+				regulator-name = "vreg_pmu_rfa_1p8";
+			};
+
+			vreg_pmu_pcie_0p9: ldo8 {
+				regulator-name = "vreg_pmu_pcie_0p9";
+			};
+
+			vreg_pmu_pcie_1p8: ldo9 {
+				regulator-name = "vreg_pmu_pcie_1p8";
+			};
+		};
+	};
+
+	// The arch_timer label is unused here, but is required by ABL to apply a dtbo
+	arch_timer: timer { };
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8550-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-bob1-supply = <&vph_pwr>;
+		vdd-bob2-supply = <&vph_pwr>;
+		vdd-l1-l4-l10-supply = <&vreg_s6g_1p8>;
+		vdd-l2-l13-l14-supply = <&vreg_bob1>;
+		vdd-l3-supply = <&vreg_s4g_1p3>;
+		vdd-l5-l16-supply = <&vreg_bob1>;
+		vdd-l6-l7-supply = <&vreg_bob1>;
+		vdd-l8-l9-supply = <&vreg_bob1>;
+		vdd-l11-supply = <&vreg_s4g_1p3>;
+		vdd-l12-supply = <&vreg_s6g_1p8>;
+		vdd-l15-supply = <&vreg_s6g_1p8>;
+		vdd-l17-supply = <&vreg_bob2>;
+
+		vreg_bob1: bob1 {
+			regulator-name = "vreg_bob1";
+			regulator-min-microvolt = <3296000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob2: bob2 {
+			regulator-name = "vreg_bob2";
+			regulator-min-microvolt = <2720000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p0: ldo2 {
+			regulator-name = "vreg_l2b_3p0";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_3p1: ldo5 {
+			regulator-name = "vreg_l5b_3p1";
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3104000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b_1p8: ldo6 {
+			regulator-name = "vreg_l6b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b_1p8: ldo7 {
+			regulator-name = "vreg_l7b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8b_1p8: ldo8 {
+			regulator-name = "vreg_l8b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b_2p9: ldo9 {
+			regulator-name = "vreg_l9b_2p9";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11b_1p2: ldo11 {
+			regulator-name = "vreg_l11b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12b_1p8: ldo12 {
+			regulator-name = "vreg_l12b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13b_3p0: ldo13 {
+			regulator-name = "vreg_l13b_3p0";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14b_3p2: ldo14 {
+			regulator-name = "vreg_l14b_3p2";
+			regulator-min-microvolt = <3200000>;
+			regulator-max-microvolt = <3200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15b_1p8: ldo15 {
+			regulator-name = "vreg_l15b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16b_2p8: ldo16 {
+			regulator-name = "vreg_l16b_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17b_2p5: ldo17 {
+			regulator-name = "vreg_l17b_2p5";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-l1-supply = <&vreg_s4g_1p3>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4e_0p95>;
+
+		vreg_l3c_0p9: ldo3 {
+			regulator-name = "vreg_l3c_0p9";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vdd-l1-supply = <&vreg_s4e_0p95>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4e_0p95>;
+
+		vreg_l1d_0p88: ldo1 {
+			regulator-name = "vreg_l1d_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-3 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-l1-supply = <&vreg_s4e_0p95>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4g_1p3>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+
+		vreg_s4e_0p95: smps4 {
+			regulator-name = "vreg_s4e_0p95";
+			regulator-min-microvolt = <904000>;
+			regulator-max-microvolt = <984000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5e_1p08: smps5 {
+			regulator-name = "vreg_s5e_1p08";
+			regulator-min-microvolt = <1010000>;
+			regulator-max-microvolt = <1120000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1e_0p88: ldo1 {
+			regulator-name = "vreg_l1e_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2e_0p9: ldo2 {
+			regulator-name = "vreg_l2e_0p9";
+			regulator-min-microvolt = <870000>;
+			regulator-max-microvolt = <970000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-4 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "f";
+
+		vdd-l1-supply = <&vreg_s4e_0p95>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4e_0p95>;
+		vdd-s4-supply = <&vph_pwr>;
+
+		vreg_s4f_0p5: smps4 {
+			regulator-name = "vreg_s4f_0p5";
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <700000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1f_0p9: ldo1 {
+			regulator-name = "vreg_l1f_0p9";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2f_0p88: ldo2 {
+			regulator-name = "vreg_l2f_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3f_0p88: ldo3 {
+			regulator-name = "vreg_l3f_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-5 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "g";
+
+		vdd-l1-supply = <&vreg_s4g_1p3>;
+		vdd-l2-supply = <&vreg_s4g_1p3>;
+		vdd-l3-supply = <&vreg_s4g_1p3>;
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+
+		vreg_s1g_1p2: smps1 {
+			regulator-name = "vreg_s1g_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s2g_0p8: smps2 {
+			regulator-name = "vreg_s2g_0p8";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s3g_0p7: smps3 {
+			regulator-name = "vreg_s3g_0p7";
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <1004000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s4g_1p3: smps4 {
+			regulator-name = "vreg_s4g_1p3";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1352000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5g_0p8: smps5 {
+			regulator-name = "vreg_s5g_0p8";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1004000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s6g_1p8: smps6 {
+			regulator-name = "vreg_s6g_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1g_1p2: ldo1 {
+			regulator-name = "vreg_l1g_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3g_1p2: ldo3 {
+			regulator-name = "vreg_l3g_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&gpi_dma1 {
+	status = "okay";
+};
+
+&gpi_dma2 {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&gpu_zap_shader {
+	firmware-name = "qcom/sm8550/a740_zap.mbn";
+};
+
+&i2c_master_hub_0 {
+	status = "okay";
+};
+
+&i2c_hub_2 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	spk_amp_l: amplifier@34 {
+		compatible = "awinic,aw88166";
+		reg = <0x34>;
+		#sound-dai-cells = <0>;
+		reset-gpios = <&tlmm 103 GPIO_ACTIVE_LOW>;
+		awinic,audio-channel = <0>;
+		awinic,sync-flag;
+		sound-name-prefix = "SPK_L";
+	};
+
+	spk_amp_r: amplifier@35 {
+		compatible = "awinic,aw88166";
+		reg = <0x35>;
+		#sound-dai-cells = <0>;
+		reset-gpios = <&tlmm 100 GPIO_ACTIVE_LOW>;
+		awinic,audio-channel = <1>;
+		awinic,sync-flag;
+		sound-name-prefix = "SPK_R";
+	};
+};
+
+&iris {
+	status = "okay";
+};
+
+&lpass_tlmm {
+	lpi_i2s3_active: lpi_i2s3-active-state {
+		sck-pins {
+			pins = "gpio12";
+			function = "i2s3_clk";
+			drive-strength = <8>;
+			bias-disable;
+			output-high;
+		};
+
+		ws-pins {
+			pins = "gpio13";
+			function = "i2s3_ws";
+			drive-strength = <8>;
+			bias-disable;
+			output-high;
+		};
+
+		data0-pins {
+			pins = "gpio17";
+			function = "i2s3_data";
+			drive-strength = <8>;
+			bias-disable;
+			output-high;
+		};
+
+		data1-pins {
+			pins = "gpio18";
+			function = "i2s3_data";
+			drive-strength = <8>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&lpass_vamacro {
+	qcom,dmic-sample-rate = <4800000>;
+};
+
+&lpass_wsamacro {
+	status = "disabled";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dsi1 {
+	vdda-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+
+	display_panel: panel@0 {
+		reg = <0>;
+
+		port {
+			panel1_in: endpoint {
+				remote-endpoint = <&mdss_dsi1_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi1_out {
+	remote-endpoint = <&panel1_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi1_phy {
+	vdds-supply = <&vreg_l1e_0p88>;
+
+	status = "okay";
+};
+
+&pcie0 {
+	perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+
+	pinctrl-0 = <&pcie0_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcieport0 {
+	wifi@0 {
+		compatible = "pci17cb,1107";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+		vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+		vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+	};
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&vreg_l1e_0p88>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&pm8550_gpios {
+	fan_pwm_active: fan-pwm-active-state {
+		pins = "gpio8";
+		function = "func1";
+		input-disable;
+		output-enable;
+		output-low;
+		bias-disable;
+		power-source = <1>;
+	};
+
+	sdc2_card_det_n: sdc2-card-det-n-state {
+		pins = "gpio12";
+		function = "normal";
+		input-enable;
+		output-disable;
+		bias-pull-up;
+		power-source = <1>;
+	};
+
+	volume_up_n: volume-up-n-state {
+		pins = "gpio6";
+		function = "normal";
+		power-source = <1>;
+		bias-pull-up;
+		input-enable;
+	};
+};
+
+&pm8550_pwm {
+	status = "okay";
+
+	pm8550_multi_led: multi-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@1 {
+			reg = <1>;
+			color = <LED_COLOR_ID_RED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@3 {
+			reg = <3>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+	};
+};
+
+&pm8550b_eusb2_repeater {
+	qcom,tune-usb2-disc-thres = /bits/ 8 <0x6>;
+	qcom,tune-usb2-amplitude = /bits/ 8 <0xb>;
+	qcom,tune-usb2-preem = /bits/ 8 <0x3>;
+	vdd18-supply = <&vreg_l15b_1p8>;
+	vdd3-supply = <&vreg_l5b_3p1>;
+};
+
+&pmk8550_gpios {
+	pmk8550_sleep_clk: sleep-clk-state {
+		pins = "gpio3";
+		function = "func1";
+		input-disable;
+		output-enable;
+		bias-disable;
+		power-source = <0>;
+	};
+
+	pwm_backlight_default: pwm-backlight-default-state {
+		pins = "gpio5";
+		function = "func3";
+		input-disable;
+		output-low;
+		output-enable;
+		bias-disable;
+		power-source = <0>;
+		qcom,drive-strength = <2>;
+	};
+};
+
+&pmk8550_rtc {
+	nvmem-cells = <&rtc_offset>;
+	nvmem-cell-names = "offset";
+};
+
+&pmk8550_sdam_2 {
+	rtc_offset: rtc-offset@bc {
+		reg = <0xbc 0x4>;
+	};
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+
+	status = "okay";
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/sm8550/ayntec/cdsp.mbn",
+			"qcom/sm8550/ayntec/cdsp_dtb.mbn";
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
+	pinctrl-names = "default", "sleep";
+	vmmc-supply = <&vreg_l9b_2p9>;
+	vqmmc-supply = <&vreg_l8b_1p8>;
+	no-sdio;
+	no-mmc;
+
+	status = "okay";
+};
+
+&sleep_clk {
+	clock-frequency = <32764>;
+};
+
+&swr1 {
+	status = "okay";
+
+	wcd_rx: codec@0,4 {
+		compatible = "sdw20217010d00";
+		reg = <0 4>;
+		qcom,rx-port-mapping = <1 2 3 4 5>;
+	};
+};
+
+&swr2 {
+	status = "okay";
+
+	wcd_tx: codec@0,3 {
+		compatible = "sdw20217010d00";
+		reg = <0 3>;
+		qcom,tx-port-mapping = <2 2 3 4>;
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <32 8>;
+
+	mcu_en_active: mcu-en-active-state {
+		pins = "gpio12";
+		function = "gpio";
+		bias-pull-down;
+	};
+
+	fan_int: fan-int-state {
+		pins = "gpio13";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	ts_s_rst_default: ts-s-rst-default-state {
+		pins = "gpio14";
+		function = "gpio";
+		bias-pull-up;
+		drive-strength = <8>;
+	};
+
+	ts_s_rst_sleep: ts-s-rst-sleep-state {
+		pins = "gpio14";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+
+	ts_s_int_default: ts-s-int-default-state {
+		pins = "gpio15";
+		function = "gpio";
+		bias-pull-up;
+		drive-strength = <8>;
+	};
+
+	ts_s_int_sleep: ts-s-int-sleep-state {
+		pins = "gpio15";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+
+	ts_p_rst_default: ts-p-rst-default-state {
+		pins = "gpio24";
+		function = "gpio";
+		bias-pull-up;
+		drive-strength = <8>;
+	};
+
+	ts_p_rst_sleep: ts-p-rst-sleep-state {
+		pins = "gpio24";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+
+	ts_p_int_default: ts-p-int-default-state {
+		pins = "gpio25";
+		function = "gpio";
+		bias-pull-up;
+		drive-strength = <8>;
+	};
+
+	ts_p_int_sleep: ts-p-int-sleep-state {
+		pins = "gpio25";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+
+	wlan_en: wlan-en-state {
+		pins = "gpio80";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-down;
+	};
+
+	bt_default: bt-default-state {
+		bt-en-pins {
+			pins = "gpio81";
+			function = "gpio";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		sw-ctrl-pins {
+			pins = "gpio82";
+			function = "gpio";
+			bias-pull-down;
+		};
+	};
+
+	dsi_p_te_active: dsi-p-te-active-state {
+		pins = "gpio86";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	dsi_p_te_suspend: dsi-s-te-suspend-state {
+		pins = "gpio86";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	dsi_s_te_active: dsi-s-te-active-state {
+		pins = "gpio87";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	dsi_s_te_suspend: dsi-s-te-suspend-state {
+		pins = "gpio87";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	wcd_default: wcd-reset-n-active-state {
+		pins = "gpio108";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+
+	fan_pwr_active: fan-pwr-active-state {
+		pins = "gpio109";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	dsi_p_rst_active: dsi-p-rst-active-state {
+		pins = "gpio133";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	dsi_p_rst_suspend: dsi-p-rst-suspend-state {
+		pins = "gpio133";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	dsi_s_rst_active: dsi-s-rst-active-state {
+		pins = "gpio137";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	dsi_s_rst_suspend: dsi-s-rst-suspend-state {
+		pins = "gpio137";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	usb0_sbu_default: usb0-sbu-state {
+		oe-n-pins {
+			pins = "gpio140";
+			function = "gpio";
+			bias-disable;
+			drive-strength = <16>;
+			output-high;
+		};
+
+		sel-pins {
+			pins = "gpio141";
+			function = "gpio";
+			bias-disable;
+			drive-strength = <16>;
+		};
+	};
+};
+
+&uart7 {
+	status = "okay";
+};
+
+&uart14 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn7850-bt";
+
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+
+		max-speed = <3200000>;
+	};
+};
+
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+	vcc-supply = <&vreg_l17b_2p5>;
+	vcc-max-microamp = <1300000>;
+	vccq-supply = <&vreg_l1g_1p2>;
+	vccq-max-microamp = <1200000>;
+	vdd-hba-supply = <&vreg_l3g_1p2>;
+
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l1d_0p88>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_hsphy {
+	phys = <&pm8550b_eusb2_repeater>;
+
+	vdd-supply = <&vreg_l1e_0p88>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_dp_qmpphy {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3f_0p88>;
+
+	status = "okay";
+};
+
+&usb_dp_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss_in>;
+};
+
+&xo_board {
+	clock-frequency = <76800000>;
+};

-- 
2.53.0

[PATCH v5 4/6] arm64: dts: qcom: Add AYN Odin 2 Mini

[Aaron Kling via B4 Relay]

From: Teguh Sobirin <teguh@sobir.in>

The AYN Odin 2 Mini is a high-performance Android-based handheld gaming
console powered by the Qualcomm Snapdragon 8 Gen 2 processor featuring a
5-inch mini-led touchscreen.

Signed-off-by: Teguh Sobirin <teguh@sobir.in>
Co-developed-by: Aaron Kling <webgeek1234@gmail.com>
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |  1 +
 .../boot/dts/qcom/qcs8550-ayntec-odin2mini.dts     | 44 ++++++++++++++++++++++
 2 files changed, 45 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 4ba8e730641949..aceb84a060f80e 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -184,6 +184,7 @@ qcs8300-ride-el2-dtbs := qcs8300-ride.dtb monaco-el2.dtbo
 
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs8300-ride-el2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-aim300-aiot.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-ayntec-odin2mini.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs9100-ride.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs9100-ride-r3.dtb
 
diff --git a/arch/arm64/boot/dts/qcom/qcs8550-ayntec-odin2mini.dts b/arch/arm64/boot/dts/qcom/qcs8550-ayntec-odin2mini.dts
new file mode 100644
index 00000000000000..cc894bdd0c9020
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs8550-ayntec-odin2mini.dts
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025, Teguh Sobirin.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "qcs8550-ayntec-common.dtsi"
+
+&{/} {
+	model = "AYN Odin 2 Mini";
+	compatible = "ayntec,odin2mini", "qcom,qcs8550", "qcom,sm8550";
+
+	vdd_disp_2v8: vdd-disp-2v8-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_disp_2v8";
+
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+
+		gpio = <&tlmm 142 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+/* There is an hdmi bridge on i2c_hub_0@48, but it is not currently supported */
+
+&remoteproc_adsp {
+	firmware-name = "qcom/sm8550/ayntec/odin2mini/adsp.mbn",
+			"qcom/sm8550/ayntec/odin2mini/adsp_dtb.mbn";
+
+	status = "okay";
+};
+
+&spk_amp_l {
+	firmware-name = "qcom/sm8550/ayntec/odin2mini/aw883xx_acf.bin";
+};
+
+&spk_amp_r {
+	firmware-name = "qcom/sm8550/ayntec/odin2mini/aw883xx_acf.bin";
+};
+

-- 
2.53.0

[PATCH v5 5/6] arm64: dts: qcom: Add AYN Odin 2 Portal

[Aaron Kling via B4 Relay]

From: Teguh Sobirin <teguh@sobir.in>

The AYN Odin 2 Portal is a high-performance Android-based handheld gaming
console powered by the Qualcomm Snapdragon 8 Gen 2 processor featuring a
7-inch OLED touchscreen.

Signed-off-by: Teguh Sobirin <teguh@sobir.in>
Co-developed-by: Aaron Kling <webgeek1234@gmail.com>
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |  1 +
 .../boot/dts/qcom/qcs8550-ayntec-odin2portal.dts   | 84 ++++++++++++++++++++++
 2 files changed, 85 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index aceb84a060f80e..6bfc4554580bd5 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -185,6 +185,7 @@ qcs8300-ride-el2-dtbs := qcs8300-ride.dtb monaco-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs8300-ride-el2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-aim300-aiot.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-ayntec-odin2mini.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-ayntec-odin2portal.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs9100-ride.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs9100-ride-r3.dtb
 
diff --git a/arch/arm64/boot/dts/qcom/qcs8550-ayntec-odin2portal.dts b/arch/arm64/boot/dts/qcom/qcs8550-ayntec-odin2portal.dts
new file mode 100644
index 00000000000000..bd6ba0ab941d33
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs8550-ayntec-odin2portal.dts
@@ -0,0 +1,84 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025, Teguh Sobirin.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "qcs8550-ayntec-common.dtsi"
+
+&{/} {
+	model = "AYN Odin 2 Portal";
+	compatible = "ayntec,odin2portal", "qcom,qcs8550", "qcom,sm8550";
+
+	vdd_bl_5v0: vdd-bl-5v0-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_bl_5v0";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&tlmm 52 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vdd_disp_2v8: vdd-disp-2v8-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_disp_2v8";
+
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+
+		gpio = <&tlmm 142 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&i2c4 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	touchscreen@38 {
+		compatible = "focaltech,ft5426";
+		reg = <0x38>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+
+		reset-gpios = <&tlmm 24 GPIO_ACTIVE_LOW>;
+
+		vcc-supply = <&vreg_l14b_3p2>;
+		iovcc-supply = <&vreg_l12b_1p8>;
+
+		pinctrl-0 = <&ts_p_rst_default &ts_p_int_default>;
+		pinctrl-1 = <&ts_p_rst_sleep &ts_p_int_sleep>;
+		pinctrl-names = "default", "sleep";
+
+		touchscreen-size-x = <1080>;
+		touchscreen-size-y = <1920>;
+		touchscreen-swapped-x-y;
+		touchscreen-inverted-y;
+	};
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/sm8550/ayntec/odin2portal/adsp.mbn",
+			"qcom/sm8550/ayntec/odin2portal/adsp_dtb.mbn";
+
+	status = "okay";
+};
+
+&spk_amp_l {
+	firmware-name = "qcom/sm8550/ayntec/odin2portal/aw883xx_acf.bin";
+};
+
+&spk_amp_r {
+	firmware-name = "qcom/sm8550/ayntec/odin2portal/aw883xx_acf.bin";
+};
+

-- 
2.53.0

[PATCH v5 6/6] arm64: dts: qcom: Add AYN Thor

[Aaron Kling via B4 Relay]

From: Teguh Sobirin <teguh@sobir.in>

The AYN Thor is a high-performance Android-based handheld gaming console
powered by the Qualcomm Snapdragon 8 Gen 2 processor featuring dual
AMOLED touchscreens.

Signed-off-by: Teguh Sobirin <teguh@sobir.in>
Co-developed-by: Aaron Kling <webgeek1234@gmail.com>
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
---
 arch/arm64/boot/dts/qcom/Makefile                |   1 +
 arch/arm64/boot/dts/qcom/qcs8550-ayntec-thor.dts | 227 +++++++++++++++++++++++
 2 files changed, 228 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 6bfc4554580bd5..6feecd62e01546 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -186,6 +186,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= qcs8300-ride-el2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-aim300-aiot.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-ayntec-odin2mini.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-ayntec-odin2portal.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-ayntec-thor.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs9100-ride.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs9100-ride-r3.dtb
 
diff --git a/arch/arm64/boot/dts/qcom/qcs8550-ayntec-thor.dts b/arch/arm64/boot/dts/qcom/qcs8550-ayntec-thor.dts
new file mode 100644
index 00000000000000..641146a9a7798e
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs8550-ayntec-thor.dts
@@ -0,0 +1,227 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025, Teguh Sobirin.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "qcs8550-ayntec-common.dtsi"
+
+&{/} {
+	model = "AYN Thor";
+	compatible = "ayntec,thor", "qcom,qcs8550", "qcom,sm8550";
+
+	vdd_bl_5v0: vdd-bl-5v0-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_bl_5v0";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&tlmm 52 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vdd_disp_1v8: vdd-disp-1v8-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_disp_1v8";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vdd_disp1_2v8: vdd-disp1-2v8-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_disp1_2v8";
+
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+
+		gpio = <&tlmm 142 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vdd_disp2_2v8: vdd-disp2-2v8-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_disp2_2v8";
+
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+
+		gpio = <&tlmm 143 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vdd_ts_3v0: vdd-ts-3v0-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_ts_3v0";
+
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+
+		gpio = <&tlmm 144 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vdd_ts_1v8: vdd-ts-1v8-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_ts_1v8";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 102 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&gpio_keys {
+	pinctrl-0 = <&volume_up_n &key_ayn_n>;
+
+	key-ayn {
+		label = "AYN Key";
+		debounce-interval = <15>;
+		gpios = <&tlmm 41 GPIO_ACTIVE_LOW>;
+		linux,code = <KEY_F24>;
+		linux,can-disable;
+	};
+
+	switch-lid {
+		label = "Hall Lid Sensor";
+		gpios = <&tlmm 17 GPIO_ACTIVE_LOW>;
+		linux,input-type = <EV_SW>;
+		linux,code = <SW_LID>;
+		linux,can-disable;
+		wakeup-source;
+	};
+};
+
+&i2c4 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	touchscreen@38 {
+		compatible = "focaltech,ft5426";
+		reg = <0x38>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+
+		reset-gpios = <&tlmm 24 GPIO_ACTIVE_LOW>;
+
+		vcc-supply = <&vreg_l14b_3p2>;
+		iovcc-supply = <&vreg_l12b_1p8>;
+
+		pinctrl-0 = <&ts_p_rst_default &ts_p_int_default>;
+		pinctrl-1 = <&ts_p_rst_sleep &ts_p_int_sleep>;
+		pinctrl-names = "default", "sleep";
+
+		touchscreen-size-x = <1080>;
+		touchscreen-size-y = <1920>;
+		touchscreen-swapped-x-y;
+		touchscreen-inverted-x;
+	};
+};
+
+&i2c_hub_3 {
+	clock-frequency = <100000>;
+
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	touchscreen@38 {
+		compatible = "focaltech,ft5452";
+		reg = <0x38>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
+
+		reset-gpios = <&tlmm 14 GPIO_ACTIVE_LOW>;
+
+		vcc-supply = <&vdd_ts_3v0>;
+		iovcc-supply = <&vdd_ts_1v8>;
+
+		pinctrl-0 = <&ts_s_rst_default &ts_s_int_default>;
+		pinctrl-1 = <&ts_s_rst_sleep &ts_s_int_sleep>;
+		pinctrl-names = "default", "sleep";
+
+		touchscreen-size-x = <1080>;
+		touchscreen-size-y = <1240>;
+		touchscreen-swapped-x-y;
+		touchscreen-inverted-x;
+	};
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	panel@0 {
+		reg = <0>;
+
+		port {
+			panel0_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel0_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	vdds-supply = <&vreg_l1e_0p88>;
+
+	status = "okay";
+};
+
+&mdss_dsi1_out {
+	qcom,te-source = "mdp_vsync_s";
+};
+
+&pm8550_multi_led {
+	status = "disabled";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/sm8550/ayntec/thor/adsp.mbn",
+			"qcom/sm8550/ayntec/thor/adsp_dtb.mbn";
+
+	status = "okay";
+};
+
+&spk_amp_l {
+	firmware-name = "qcom/sm8550/ayntec/thor/aw883xx_acf.bin";
+};
+
+&spk_amp_r {
+	firmware-name = "qcom/sm8550/ayntec/thor/aw883xx_acf.bin";
+};
+
+&tlmm {
+	key_ayn_n: key-ayn-n-state {
+		pins = "gpio41";
+		function = "gpio";
+		bias-pull-up;
+		output-disable;
+	};
+};

-- 
2.53.0

Re: [PATCH v5 6/6] arm64: dts: qcom: Add AYN Thor

[Konrad Dybcio]

On 4/8/26 9:41 PM, Aaron Kling via B4 Relay wrote:
> From: Teguh Sobirin <teguh@sobir.in>
> 
> The AYN Thor is a high-performance Android-based handheld gaming console
> powered by the Qualcomm Snapdragon 8 Gen 2 processor featuring dual
> AMOLED touchscreens.
> 
> Signed-off-by: Teguh Sobirin <teguh@sobir.in>
> Co-developed-by: Aaron Kling <webgeek1234@gmail.com>
> Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad

Re: [PATCH v5 3/6] arm64: dts: qcom: Add AYN QCS8550 Common

[Konrad Dybcio]

On 4/8/26 9:41 PM, Aaron Kling via B4 Relay wrote:
> From: Teguh Sobirin <teguh@sobir.in>
> 
> This contains everything common between the AYN QCS8550 devices. It will
> be included by device specific dts'.
> 
> Signed-off-by: Teguh Sobirin <teguh@sobir.in>
> Co-developed-by: Aaron Kling <webgeek1234@gmail.com>
> Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
> ---

[...]

> +	// The tzlog label is required by ABL to apply a dtbo, but it can be on any node

I don't know if the policy changed, but I think C-style (/* Foo */)
comments are still preferred

[...]


> +	// The arch_timer label is unused here, but is required by ABL to apply a dtbo
> +	arch_timer: timer { };

ditto

[...]

> +&pm8550_gpios {
> +	fan_pwm_active: fan-pwm-active-state {
> +		pins = "gpio8";
> +		function = "func1";
> +		input-disable;
> +		output-enable;
> +		output-low;

Looks like this should be a regulator then, probably?

[...]

> +	wcd_default: wcd-reset-n-active-state {
> +		pins = "gpio108";
> +		function = "gpio";
> +		drive-strength = <16>;
> +		bias-disable;
> +		output-low;

no need for this property

> +	};
> +
> +	fan_pwr_active: fan-pwr-active-state {
> +		pins = "gpio109";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-disable;
> +		output-low;

likewise, especially since it's the opposite of the active state
defined in the vreg node

[...]

> +	usb0_sbu_default: usb0-sbu-state {
> +		oe-n-pins {
> +			pins = "gpio140";
> +			function = "gpio";
> +			bias-disable;
> +			drive-strength = <16>;
> +			output-high;

This is probably not required too.. unless there's a hw bug?

fwiw 16 mA is a very high drive-strength - does this come from vendor
sources?

Konrad

Re: [PATCH v5 3/6] arm64: dts: qcom: Add AYN QCS8550 Common

[Aaron Kling]

On Fri, Apr 24, 2026 at 7:11 AM Konrad Dybcio
<konrad.dybcio@oss.qualcomm.com> wrote:
>
> On 4/8/26 9:41 PM, Aaron Kling via B4 Relay wrote:
> > From: Teguh Sobirin <teguh@sobir.in>
> >
> > This contains everything common between the AYN QCS8550 devices. It will
> > be included by device specific dts'.
> >
> > Signed-off-by: Teguh Sobirin <teguh@sobir.in>
> > Co-developed-by: Aaron Kling <webgeek1234@gmail.com>
> > Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
> > ---
>
> [...]
>
> > +     // The tzlog label is required by ABL to apply a dtbo, but it can be on any node
>
> I don't know if the policy changed, but I think C-style (/* Foo */)
> comments are still preferred

Ack

> [...]
>
>
> > +     // The arch_timer label is unused here, but is required by ABL to apply a dtbo
> > +     arch_timer: timer { };
>
> ditto

Ack

> [...]
>
> > +&pm8550_gpios {
> > +     fan_pwm_active: fan-pwm-active-state {
> > +             pins = "gpio8";
> > +             function = "func1";
> > +             input-disable;
> > +             output-enable;
> > +             output-low;
>
> Looks like this should be a regulator then, probably?

Mmm, what would it be tied to, then? The fan already has a reg. I
presume just modeling it as an always on reg tied to nothing is
undesirable. I also have no idea what the voltage would be.

> [...]
>
> > +     wcd_default: wcd-reset-n-active-state {
> > +             pins = "gpio108";
> > +             function = "gpio";
> > +             drive-strength = <16>;
> > +             bias-disable;
> > +             output-low;
>
> no need for this property

I'll start with saying that I know basically nothing about qcom
hardware design and what the average pinmuxing layout looks like. But
I do note that a lot of existing devices have this exact same node,
for example the sm8550 hdk [0]. Is there something that makes these
devices different? Or is this unnecessary everywhere?

> > +     };
> > +
> > +     fan_pwr_active: fan-pwr-active-state {
> > +             pins = "gpio109";
> > +             function = "gpio";
> > +             drive-strength = <2>;
> > +             bias-disable;
> > +             output-low;
>
> likewise, especially since it's the opposite of the active state
> defined in the vreg node

Ack, this one makes sense since the fan power sequence will set stuff
as necessary.

> [...]
>
> > +     usb0_sbu_default: usb0-sbu-state {
> > +             oe-n-pins {
> > +                     pins = "gpio140";
> > +                     function = "gpio";
> > +                     bias-disable;
> > +                     drive-strength = <16>;
> > +                     output-high;
>
> This is probably not required too.. unless there's a hw bug?
>
> fwiw 16 mA is a very high drive-strength - does this come from vendor
> sources?

I do not see any pinmux for gpio140 in the downstream dt or anything
matching pi3usb102 at all, I'm not sure how it's handled there. The
original source of this dt was written before there was a public gpl
code release from AYN. I do see other qcom users of the pi3usb102
doing similar however, for example the sc8280xp crd [1]. So I've got
the same question as above: is there something different here, or is
it possible other existing copies of this are also wrong?

Aaron

[0] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm64/boot/dts/qcom/sm8550-hdk.dts?h=v7.0#n1302
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts?h=v7.0#n1175

Re: [PATCH v5 3/6] arm64: dts: qcom: Add AYN QCS8550 Common

[Konrad Dybcio]

On 4/27/26 12:01 AM, Aaron Kling wrote:
> On Fri, Apr 24, 2026 at 7:11 AM Konrad Dybcio
> <konrad.dybcio@oss.qualcomm.com> wrote:
>>
>> On 4/8/26 9:41 PM, Aaron Kling via B4 Relay wrote:
>>> From: Teguh Sobirin <teguh@sobir.in>
>>>
>>> This contains everything common between the AYN QCS8550 devices. It will
>>> be included by device specific dts'.
>>>
>>> Signed-off-by: Teguh Sobirin <teguh@sobir.in>
>>> Co-developed-by: Aaron Kling <webgeek1234@gmail.com>
>>> Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
>>> ---

[...]
>>> +&pm8550_gpios {
>>> +     fan_pwm_active: fan-pwm-active-state {
>>> +             pins = "gpio8";
>>> +             function = "func1";
>>> +             input-disable;
>>> +             output-enable;
>>> +             output-low;
>>
>> Looks like this should be a regulator then, probably?
> 
> Mmm, what would it be tied to, then? The fan already has a reg. I
> presume just modeling it as an always on reg tied to nothing is
> undesirable. I also have no idea what the voltage would be.

Or maybe it's some sort of reset/enable GPIO. Or an enable pin to
whatever feeds into VDD_FAN_5V0. It's hard to tell indeed.

> 
>> [...]
>>
>>> +     wcd_default: wcd-reset-n-active-state {
>>> +             pins = "gpio108";
>>> +             function = "gpio";
>>> +             drive-strength = <16>;
>>> +             bias-disable;
>>> +             output-low;
>>
>> no need for this property
> 
> I'll start with saying that I know basically nothing about qcom
> hardware design and what the average pinmuxing layout looks like. But
> I do note that a lot of existing devices have this exact same node,
> for example the sm8550 hdk [0]. Is there something that makes these
> devices different? Or is this unnecessary everywhere?

That's my understanding.

[...]

>>> +     usb0_sbu_default: usb0-sbu-state {
>>> +             oe-n-pins {
>>> +                     pins = "gpio140";
>>> +                     function = "gpio";
>>> +                     bias-disable;
>>> +                     drive-strength = <16>;
>>> +                     output-high;
>>
>> This is probably not required too.. unless there's a hw bug?
>>
>> fwiw 16 mA is a very high drive-strength - does this come from vendor
>> sources?
> 
> I do not see any pinmux for gpio140 in the downstream dt or anything
> matching pi3usb102 at all, I'm not sure how it's handled there. The
> original source of this dt was written before there was a public gpl
> code release from AYN. I do see other qcom users of the pi3usb102
> doing similar however, for example the sc8280xp crd [1]. So I've got
> the same question as above: is there something different here, or is
> it possible other existing copies of this are also wrong?

You can retrieve the settings from your device at runtime,
/sys/kernel/debug/gpio will read back the hw settings

As for the CRD, I don't know. It may as well be board-specific.

Konrad

Re: [PATCH v5 3/6] arm64: dts: qcom: Add AYN QCS8550 Common

[Aaron Kling]

On Mon, Apr 27, 2026 at 9:45 AM Konrad Dybcio
<konrad.dybcio@oss.qualcomm.com> wrote:
>
> On 4/27/26 12:01 AM, Aaron Kling wrote:
> > On Fri, Apr 24, 2026 at 7:11 AM Konrad Dybcio
> > <konrad.dybcio@oss.qualcomm.com> wrote:
> >>
> >> On 4/8/26 9:41 PM, Aaron Kling via B4 Relay wrote:
> >>> From: Teguh Sobirin <teguh@sobir.in>
> >>>
> >>> This contains everything common between the AYN QCS8550 devices. It will
> >>> be included by device specific dts'.
> >>>
> >>> Signed-off-by: Teguh Sobirin <teguh@sobir.in>
> >>> Co-developed-by: Aaron Kling <webgeek1234@gmail.com>
> >>> Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
> >>> ---
>
> [...]
> >>> +&pm8550_gpios {
> >>> +     fan_pwm_active: fan-pwm-active-state {
> >>> +             pins = "gpio8";
> >>> +             function = "func1";
> >>> +             input-disable;
> >>> +             output-enable;
> >>> +             output-low;
> >>
> >> Looks like this should be a regulator then, probably?
> >
> > Mmm, what would it be tied to, then? The fan already has a reg. I
> > presume just modeling it as an always on reg tied to nothing is
> > undesirable. I also have no idea what the voltage would be.
>
> Or maybe it's some sort of reset/enable GPIO. Or an enable pin to
> whatever feeds into VDD_FAN_5V0. It's hard to tell indeed.

Talking to someone working on the downstream kernel for these devices,
the purpose of this is to set the pin to 'func1' or pwm4 output. It's
not a regulator or reset or something that needs otherwise modeled.

> >
> >> [...]
> >>
> >>> +     wcd_default: wcd-reset-n-active-state {
> >>> +             pins = "gpio108";
> >>> +             function = "gpio";
> >>> +             drive-strength = <16>;
> >>> +             bias-disable;
> >>> +             output-low;
> >>
> >> no need for this property
> >
> > I'll start with saying that I know basically nothing about qcom
> > hardware design and what the average pinmuxing layout looks like. But
> > I do note that a lot of existing devices have this exact same node,
> > for example the sm8550 hdk [0]. Is there something that makes these
> > devices different? Or is this unnecessary everywhere?
>
> That's my understanding.
>
> [...]
>
> >>> +     usb0_sbu_default: usb0-sbu-state {
> >>> +             oe-n-pins {
> >>> +                     pins = "gpio140";
> >>> +                     function = "gpio";
> >>> +                     bias-disable;
> >>> +                     drive-strength = <16>;
> >>> +                     output-high;
> >>
> >> This is probably not required too.. unless there's a hw bug?
> >>
> >> fwiw 16 mA is a very high drive-strength - does this come from vendor
> >> sources?
> >
> > I do not see any pinmux for gpio140 in the downstream dt or anything
> > matching pi3usb102 at all, I'm not sure how it's handled there. The
> > original source of this dt was written before there was a public gpl
> > code release from AYN. I do see other qcom users of the pi3usb102
> > doing similar however, for example the sc8280xp crd [1]. So I've got
> > the same question as above: is there something different here, or is
> > it possible other existing copies of this are also wrong?
>
> You can retrieve the settings from your device at runtime,
> /sys/kernel/debug/gpio will read back the hw settings
>
> As for the CRD, I don't know. It may as well be board-specific.

I got pointed in the right direction to see this on downstream. The
active drive strength on gpio140/141 is 8. Does this seem more
reasonable?

Aaron