Devicetree
 help / color / mirror / Atom feed
From: Dinh Nguyen <dinguyen@kernel.org>
To: Tanmay Kathpalia <tanmay.kathpalia@altera.com>,
	linux-mmc@vger.kernel.org
Cc: ulfh@kernel.org, adrian.hunter@intel.com, krzk+dt@kernel.org,
	robh@kernel.org, conor+dt@kernel.org, p.zabel@pengutronix.de,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH v4 2/8] arm64: dts: agilex5: add SD/eMMC host controller
Date: Wed, 19 Aug 2026 08:04:45 -0500	[thread overview]
Message-ID: <fcc5c96a-5b68-4eb3-bee2-952aa9029631@kernel.org> (raw)
In-Reply-To: <20260810190025.25045-3-tanmay.kathpalia@altera.com>



On 8/10/26 14:00, Tanmay Kathpalia wrote:
> The Agilex5 HPS includes a Cadence SD6HC that drives either an SD card
> or eMMC, depending on the SOCDK daughter card. It uses separate SDMCLK
> (CIU) and L4_MP (BIU) clocks, and has three resets for the host
> controller, Combo PHY, and SDMMC OCP bridge. DMA for this controller
> requires the SMMU (stream ID 5), so the SOCDK board enables it.
> 
> On the SOCDK OOBE card the slot is SD-only: fixed 3.3 V card supply and
> a GPIO-selected 3.3 V / 1.8 V I/O supply for UHS-I signalling up to
> SDR104.
> 
> Signed-off-by: Tanmay Kathpalia <tanmay.kathpalia@altera.com>
> ---
> Depends on commit ab45ecfab540 ("dt-bindings: reset: altr: add
> COMBOPHY_RESET for Agilex5"), which is already in mainline via the
> reset tree. It is not yet in mmc/next; apply or merge that commit when
> building/testing this patch on top of mmc/next.
> 
>   .../arm64/boot/dts/intel/socfpga_agilex5.dtsi | 25 ++++++++++++
>   .../boot/dts/intel/socfpga_agilex5_socdk.dts  | 38 ++++++++++++++++++-
>   2 files changed, 62 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/intel/socfpga_agilex5.dtsi b/arch/arm64/boot/dts/intel/socfpga_agilex5.dtsi
> index b06c6d5d60ee..5ccbd7bf2034 100644
> --- a/arch/arm64/boot/dts/intel/socfpga_agilex5.dtsi
> +++ b/arch/arm64/boot/dts/intel/socfpga_agilex5.dtsi
> @@ -300,6 +300,31 @@ portb: gpio-controller@0 {
>   			};
>   		};
>   
> +		/*
> +		 * Shared SD/eMMC controller node. On the SOCDK OOBE daughter-card
> +		 * this is used for SD card operation; on the SOCDK eMMC daughter-card
> +		 * it is configured for eMMC.
> +		 */
> +		emmc: mmc@10808000 {
> +			compatible = "altr,agilex5-sd6hc", "cdns,sd6hc";
> +			reg = <0x10808000 0x1000>;
> +			/*
> +			 * "ciu" (SDMCLK) is listed first so it is selected as the
> +			 * primary clock by the SDHCI platform layer; the SD6HC PHY
> +			 * timing calculations are derived from this clock rate.
> +			 */
> +			clocks = <&clkmgr AGILEX5_SDMCLK>, <&clkmgr AGILEX5_L4_MP_CLK>;
> +			clock-names = "ciu", "biu";
> +			dma-coherent;
> +			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> +			iommus = <&smmu 5>;
> +			resets = <&rst SDMMC_RESET>, <&rst COMBOPHY_RESET>,
> +				 <&rst SDMMC_OCP_RESET>;
> +			reset-names = "sdhc-reset", "combophy", "sdmmc-ocp";
> +
> +			status = "disabled";
> +		};
> +
>   		nand: nand-controller@10b80000 {
>   			compatible = "cdns,hp-nfc";
>   			reg = <0x10b80000 0x10000>,
> diff --git a/arch/arm64/boot/dts/intel/socfpga_agilex5_socdk.dts b/arch/arm64/boot/dts/intel/socfpga_agilex5_socdk.dts
> index 57d3c5807c65..f37038066922 100644
> --- a/arch/arm64/boot/dts/intel/socfpga_agilex5_socdk.dts
> +++ b/arch/arm64/boot/dts/intel/socfpga_agilex5_socdk.dts
> @@ -36,9 +36,37 @@ memory@80000000 {
>   		/* We expect the bootloader to fill in the reg */
>   		reg = <0x0 0x80000000 0x0 0x0>;
>   	};
> +
> +	vqmmc_io_reg: regulator-1p8v {
> +		compatible = "regulator-gpio";
> +		gpios = <&portb 3 GPIO_ACTIVE_HIGH>;
> +		gpios-states = <0>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-min-microvolt = <1800000>;
> +		regulator-name = "vqmmc-io";
> +		states = <1800000 0x1>,
> +			 <3300000 0x0>;
> +	};
> +
> +	vmmc_reg: regulator-fixed-3p3v {
> +		compatible = "regulator-fixed";
> +		regulator-always-on;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-name = "vcc-sd";
> +	};
>   };
>   
> -&gpio0 {
> +&emmc {
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	disable-wp;
> +	max-frequency = <200000000>;
> +	no-mmc;
> +	sd-uhs-sdr104;
> +	vmmc-supply = <&vmmc_reg>;
> +	vqmmc-supply = <&vqmmc_io_reg>;
> +
>   	status = "okay";
>   };
>   
> @@ -59,6 +87,10 @@ emac2_phy0: ethernet-phy@0 {
>   	};
>   };
>   
> +&gpio0 {
> +	status = "okay";
> +};
> +
>   &gpio1 {
>   	status = "okay";
>   };
> @@ -100,6 +132,10 @@ root: partition@4200000 {
>   	};
>   };
>   
> +&smmu {
> +	status = "okay";
> +};
> +

you should no longer need this because of

10cf797f3f8a ("arm64: dts: socfpga: agilex5: Enable the SMMU")

Thanks,
Dinh


  reply	other threads:[~2026-08-19 13:04 UTC|newest]

Thread overview: 14+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-08-10 19:00 [PATCH v4 0/8] mmc: sdhci-cadence: add SD6HC support and Agilex5 enablement Tanmay Kathpalia
2026-08-10 19:00 ` [PATCH v4 1/8] dt-bindings: mmc: add Cadence SD6HC binding Tanmay Kathpalia
2026-08-12 10:29   ` Krzysztof Kozlowski
2026-08-10 19:00 ` [PATCH v4 2/8] arm64: dts: agilex5: add SD/eMMC host controller Tanmay Kathpalia
2026-08-19 13:04   ` Dinh Nguyen [this message]
2026-08-10 19:00 ` [PATCH v4 3/8] dt-bindings: arm: altera: add Agilex5 SOCDK eMMC board variant Tanmay Kathpalia
2026-08-10 19:10   ` sashiko-bot
2026-08-10 19:18     ` Kathpalia, Tanmay
2026-08-10 19:00 ` [PATCH v4 4/8] arm64: dts: agilex5: add SOCDK eMMC daughter board Tanmay Kathpalia
2026-08-10 19:00 ` [PATCH v4 5/8] mmc: sdhci-cadence: rename SD4HC symbols for SD6HC groundwork Tanmay Kathpalia
2026-08-10 19:00 ` [PATCH v4 6/8] mmc: sdhci-cadence: refactor driver structure for V6 controller support Tanmay Kathpalia
2026-08-10 19:00 ` [PATCH v4 7/8] mmc: sdhci-cadence: add Cadence SD6HC support Tanmay Kathpalia
2026-08-10 19:18   ` sashiko-bot
2026-08-10 19:00 ` [PATCH v4 8/8] mmc: sdhci-cadence: add Altera Agilex5 " Tanmay Kathpalia

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=fcc5c96a-5b68-4eb3-bee2-952aa9029631@kernel.org \
    --to=dinguyen@kernel.org \
    --cc=adrian.hunter@intel.com \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=krzk+dt@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mmc@vger.kernel.org \
    --cc=p.zabel@pengutronix.de \
    --cc=robh@kernel.org \
    --cc=tanmay.kathpalia@altera.com \
    --cc=ulfh@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox