* Re: [PATCH] ARM: dts: imx6qdl-gw5910: add support for bcm4330-bt
From: Shawn Guo @ 2020-05-20 2:18 UTC (permalink / raw)
To: Tim Harvey
Cc: Rob Herring, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-arm-kernel, linux-kernel
In-Reply-To: <1589320455-23844-1-git-send-email-tharvey@gateworks.com>
On Tue, May 12, 2020 at 02:54:15PM -0700, Tim Harvey wrote:
> The Sterling-LWB has a BCM4330 which has a UART based bluetooth
> HCI. Add support for binding to the bcm_hci driver to take care
> of handling the shutdown gpio and loading firmware.
>
> Because the shutdown gpio is more of an enable than a regulator
> go ahead and replace the regulator with a shutdown-gpio.
>
> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Applied, thanks.
^ permalink raw reply
* Re: [PATCH] ARM: dts: imx6qdl-gw5904: add lsm9ds1 iio imu/magn support
From: Shawn Guo @ 2020-05-20 2:18 UTC (permalink / raw)
To: Tim Harvey
Cc: Rob Herring, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-arm-kernel, linux-kernel
In-Reply-To: <1589317196-8864-1-git-send-email-tharvey@gateworks.com>
On Tue, May 12, 2020 at 01:59:56PM -0700, Tim Harvey wrote:
> Add one node for the accel/gyro i2c device and another for the separate
> magnetometer device in the lsm9ds1.
>
> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Applied, thanks.
^ permalink raw reply
* Re: [PATCH] ARM: dts: imx6qdl-gw560x: add lsm9ds1 iio imu/magn support
From: Shawn Guo @ 2020-05-20 2:16 UTC (permalink / raw)
To: Tim Harvey
Cc: Rob Herring, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-arm-kernel, linux-kernel
In-Reply-To: <1589317177-8703-1-git-send-email-tharvey@gateworks.com>
On Tue, May 12, 2020 at 01:59:37PM -0700, Tim Harvey wrote:
> Add one node for the accel/gyro i2c device and another for the separate
> magnetometer device in the lsm9ds1.
>
> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Applied, thanks.
^ permalink raw reply
* [PATCH 3/3] arm64: dts: imx8mp: add mu node
From: peng.fan @ 2020-05-20 2:04 UTC (permalink / raw)
To: shawnguo, fabio.estevam, kernel, aisheng.dong, robh+dt, sboyd
Cc: linux-arm-kernel, linux-kernel, linux-imx, leonard.crestez,
daniel.baluta, l.stach, devicetree, linux-clk, Peng Fan
In-Reply-To: <1589940278-3680-1-git-send-email-peng.fan@nxp.com>
From: Peng Fan <peng.fan@nxp.com>
Add mu node to let A53 could communicate with M Core.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8mp.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
index 73535601261e..0b127a25657a 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
@@ -621,6 +621,15 @@
status = "disabled";
};
+ mu: mailbox@30aa0000 {
+ compatible = "fsl,imx6sx-mu";
+ reg = <0x30aa0000 0x10000>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_MU_ROOT>;
+ clock-names = "mu";
+ #mbox-cells = <2>;
+ };
+
i2c5: i2c@30ad0000 {
compatible = "fsl,imx8mp-i2c", "fsl,imx21-i2c";
#address-cells = <1>;
--
2.16.4
^ permalink raw reply related
* [PATCH 2/3] clk: imx8mp: add mu root clk
From: peng.fan @ 2020-05-20 2:04 UTC (permalink / raw)
To: shawnguo, fabio.estevam, kernel, aisheng.dong, robh+dt, sboyd
Cc: linux-arm-kernel, linux-kernel, linux-imx, leonard.crestez,
daniel.baluta, l.stach, devicetree, linux-clk, Peng Fan
In-Reply-To: <1589940278-3680-1-git-send-email-peng.fan@nxp.com>
From: Peng Fan <peng.fan@nxp.com>
Add mu root clk for mu mailbox usage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
drivers/clk/imx/clk-imx8mp.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/clk/imx/clk-imx8mp.c b/drivers/clk/imx/clk-imx8mp.c
index 41469e2cc3de..95eeb9eef70c 100644
--- a/drivers/clk/imx/clk-imx8mp.c
+++ b/drivers/clk/imx/clk-imx8mp.c
@@ -677,6 +677,7 @@ static int imx8mp_clocks_probe(struct platform_device *pdev)
hws[IMX8MP_CLK_I2C2_ROOT] = imx_clk_hw_gate4("i2c2_root_clk", "i2c2", ccm_base + 0x4180, 0);
hws[IMX8MP_CLK_I2C3_ROOT] = imx_clk_hw_gate4("i2c3_root_clk", "i2c3", ccm_base + 0x4190, 0);
hws[IMX8MP_CLK_I2C4_ROOT] = imx_clk_hw_gate4("i2c4_root_clk", "i2c4", ccm_base + 0x41a0, 0);
+ hws[IMX8MP_CLK_MU_ROOT] = imx_clk_hw_gate4("mu_root_clk", "ipg_root", ccm_base + 0x4210, 0);
hws[IMX8MP_CLK_OCOTP_ROOT] = imx_clk_hw_gate4("ocotp_root_clk", "ipg_root", ccm_base + 0x4220, 0);
hws[IMX8MP_CLK_PCIE_ROOT] = imx_clk_hw_gate4("pcie_root_clk", "pcie_aux", ccm_base + 0x4250, 0);
hws[IMX8MP_CLK_PWM1_ROOT] = imx_clk_hw_gate4("pwm1_root_clk", "pwm1", ccm_base + 0x4280, 0);
--
2.16.4
^ permalink raw reply related
* [PATCH 1/3] arm64: dts: imx8m: add mu node
From: peng.fan @ 2020-05-20 2:04 UTC (permalink / raw)
To: shawnguo, fabio.estevam, kernel, aisheng.dong, robh+dt, sboyd
Cc: linux-arm-kernel, linux-kernel, linux-imx, leonard.crestez,
daniel.baluta, l.stach, devicetree, linux-clk, Peng Fan
In-Reply-To: <1589940278-3680-1-git-send-email-peng.fan@nxp.com>
From: Peng Fan <peng.fan@nxp.com>
Add mu node to let A53 could communicate with M Core.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8mm.dtsi | 9 +++++++++
arch/arm64/boot/dts/freescale/imx8mn.dtsi | 9 +++++++++
arch/arm64/boot/dts/freescale/imx8mq.dtsi | 9 +++++++++
3 files changed, 27 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
index f3bbefe3e59f..9722f76d8c3f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -771,6 +771,15 @@
status = "disabled";
};
+ mu: mailbox@30aa0000 {
+ compatible = "fsl,imx6sx-mu";
+ reg = <0x30aa0000 0x10000>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MM_CLK_MU_ROOT>;
+ clock-names = "mu";
+ #mbox-cells = <2>;
+ };
+
usdhc1: mmc@30b40000 {
compatible = "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
reg = <0x30b40000 0x10000>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mn.dtsi b/arch/arm64/boot/dts/freescale/imx8mn.dtsi
index fb63a98fdff5..5f30f1d50460 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mn.dtsi
@@ -671,6 +671,15 @@
status = "disabled";
};
+ mu: mailbox@30aa0000 {
+ compatible = "fsl,imx6sx-mu";
+ reg = <0x30aa0000 0x10000>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_MU_ROOT>;
+ clock-names = "mu";
+ #mbox-cells = <2>;
+ };
+
usdhc1: mmc@30b40000 {
compatible = "fsl,imx8mn-usdhc", "fsl,imx7d-usdhc";
reg = <0x30b40000 0x10000>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
index 1d15680a4962..e969fcbbd15f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
@@ -956,6 +956,15 @@
status = "disabled";
};
+ mu: mailbox@30aa0000 {
+ compatible = "fsl,imx6sx-mu";
+ reg = <0x30aa0000 0x10000>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MQ_CLK_MU_ROOT>;
+ clock-names = "mu";
+ #mbox-cells = <2>;
+ };
+
usdhc1: mmc@30b40000 {
compatible = "fsl,imx8mq-usdhc",
"fsl,imx7d-usdhc";
--
2.16.4
^ permalink raw reply related
* [PATCH 0/3] imx8m: add mu support
From: peng.fan @ 2020-05-20 2:04 UTC (permalink / raw)
To: shawnguo, fabio.estevam, kernel, aisheng.dong, robh+dt, sboyd
Cc: linux-arm-kernel, linux-kernel, linux-imx, leonard.crestez,
daniel.baluta, l.stach, devicetree, linux-clk, Peng Fan
From: Peng Fan <peng.fan@nxp.com>
patch 1,3 is to add mu node
Patch 2 is to add mu root clk for i.MX8MP
Patch 1,3 is not merged, since patch 3 depends on patch 2 to make mu work.
Peng Fan (3):
arm64: dts: imx8m: add mu node
clk: imx8mp: add mu root clk
arm64: dts: imx8mp: add mu node
arch/arm64/boot/dts/freescale/imx8mm.dtsi | 9 +++++++++
arch/arm64/boot/dts/freescale/imx8mn.dtsi | 9 +++++++++
arch/arm64/boot/dts/freescale/imx8mp.dtsi | 9 +++++++++
arch/arm64/boot/dts/freescale/imx8mq.dtsi | 9 +++++++++
drivers/clk/imx/clk-imx8mp.c | 1 +
5 files changed, 37 insertions(+)
--
2.16.4
^ permalink raw reply
* [PATCH 4/4] arm64: dts: imx8mp: add i2c aliases
From: peng.fan @ 2020-05-20 2:02 UTC (permalink / raw)
To: shawnguo, fabio.estevam, kernel, aisheng.dong
Cc: linux-arm-kernel, linux-kernel, linux-imx, leonard.crestez,
daniel.baluta, l.stach, devicetree, Peng Fan
In-Reply-To: <1589940166-736-1-git-send-email-peng.fan@nxp.com>
From: Peng Fan <peng.fan@nxp.com>
The devices could be enumerated properly with aliases.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8mp.dtsi | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
index 014205fc24f6..73535601261e 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
@@ -23,6 +23,12 @@
gpio2 = &gpio3;
gpio3 = &gpio4;
gpio4 = &gpio5;
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ i2c3 = &i2c4;
+ i2c4 = &i2c5;
+ i2c5 = &i2c6;
mmc0 = &usdhc1;
mmc1 = &usdhc2;
mmc2 = &usdhc3;
--
2.16.4
^ permalink raw reply related
* [PATCH 3/4] arm64: dts: imx8mm: sort the aliases
From: peng.fan @ 2020-05-20 2:02 UTC (permalink / raw)
To: shawnguo, fabio.estevam, kernel, aisheng.dong
Cc: linux-arm-kernel, linux-kernel, linux-imx, leonard.crestez,
daniel.baluta, l.stach, devicetree, Peng Fan
In-Reply-To: <1589940166-736-1-git-send-email-peng.fan@nxp.com>
From: Peng Fan <peng.fan@nxp.com>
Sort the aliases alphabetically.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8mm.dtsi | 16 ++++++++--------
1 file changed, 8 insertions(+), 8 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
index c63685ae80ee..f3bbefe3e59f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -18,10 +18,18 @@
aliases {
ethernet0 = &fec1;
+ gpio0 = &gpio1;
+ gpio1 = &gpio2;
+ gpio2 = &gpio3;
+ gpio3 = &gpio4;
+ gpio4 = &gpio5;
i2c0 = &i2c1;
i2c1 = &i2c2;
i2c2 = &i2c3;
i2c3 = &i2c4;
+ mmc0 = &usdhc1;
+ mmc1 = &usdhc2;
+ mmc2 = &usdhc3;
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
@@ -29,14 +37,6 @@
spi0 = &ecspi1;
spi1 = &ecspi2;
spi2 = &ecspi3;
- mmc0 = &usdhc1;
- mmc1 = &usdhc2;
- mmc2 = &usdhc3;
- gpio0 = &gpio1;
- gpio1 = &gpio2;
- gpio2 = &gpio3;
- gpio3 = &gpio4;
- gpio4 = &gpio5;
};
cpus {
--
2.16.4
^ permalink raw reply related
* [PATCH 2/4] arm64: dts: imx8mq: Add ethernet alias
From: peng.fan @ 2020-05-20 2:02 UTC (permalink / raw)
To: shawnguo, fabio.estevam, kernel, aisheng.dong
Cc: linux-arm-kernel, linux-kernel, linux-imx, leonard.crestez,
daniel.baluta, l.stach, devicetree, Peng Fan
In-Reply-To: <1589940166-736-1-git-send-email-peng.fan@nxp.com>
From: Peng Fan <peng.fan@nxp.com>
Add ethernet alias, so bootloader code can use this to find the
primary ethernet device, and set the MAC address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8mq.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
index 9d3c9693d713..1d15680a4962 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
@@ -20,6 +20,7 @@
#size-cells = <2>;
aliases {
+ ethernet0 = &fec1;
gpio0 = &gpio1;
gpio1 = &gpio2;
gpio2 = &gpio3;
--
2.16.4
^ permalink raw reply related
* [PATCH 1/4] arm64: dts: imx8mq: Add mmc aliases
From: peng.fan @ 2020-05-20 2:02 UTC (permalink / raw)
To: shawnguo, fabio.estevam, kernel, aisheng.dong
Cc: linux-arm-kernel, linux-kernel, linux-imx, leonard.crestez,
daniel.baluta, l.stach, devicetree, Peng Fan
In-Reply-To: <1589940166-736-1-git-send-email-peng.fan@nxp.com>
From: Peng Fan <peng.fan@nxp.com>
Add mmc aliases for kernel usage
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8mq.dtsi | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
index bab88369be1b..9d3c9693d713 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
@@ -29,6 +29,8 @@
i2c1 = &i2c2;
i2c2 = &i2c3;
i2c3 = &i2c4;
+ mmc0 = &usdhc1;
+ mmc1 = &usdhc2;
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
--
2.16.4
^ permalink raw reply related
* [PATCH 0/4] arm64: dts: imx8m: dtb aliases update
From: peng.fan @ 2020-05-20 2:02 UTC (permalink / raw)
To: shawnguo, fabio.estevam, kernel, aisheng.dong
Cc: linux-arm-kernel, linux-kernel, linux-imx, leonard.crestez,
daniel.baluta, l.stach, devicetree, Peng Fan
From: Peng Fan <peng.fan@nxp.com>
Minor patchset to update device tree aliases
Peng Fan (4):
arm64: dts: imx8mq: Add mmc aliases
arm64: dts: imx8mq: Add ethernet alias
arm64: dts: imx8mm: sort the aliases
arm64: dts: imx8mp: add i2c aliases
arch/arm64/boot/dts/freescale/imx8mm.dtsi | 16 ++++++++--------
arch/arm64/boot/dts/freescale/imx8mp.dtsi | 6 ++++++
arch/arm64/boot/dts/freescale/imx8mq.dtsi | 3 +++
3 files changed, 17 insertions(+), 8 deletions(-)
--
2.16.4
^ permalink raw reply
* Re: [PATCH v2 1/2] dt-bindings: chrome: Add cros-ec-typec mux props
From: Prashant Malani @ 2020-05-20 1:51 UTC (permalink / raw)
To: linux-kernel
Cc: heikki.krogerus, Benson Leung,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Enric Balletbo i Serra, Guenter Roeck, Rob Herring
In-Reply-To: <20200518071707.161843-1-pmalani@chromium.org>
Hi Rob,
On Mon, May 18, 2020 at 12:17:04AM -0700, Prashant Malani wrote:
> Add properties for mode, orientation and USB data role switches for
> Type C connectors. When available, these will allow the Type C connector
> class port driver to configure the various switches according to USB PD
> information (like orientation, alt mode etc.) provided by the Chrome OS
> EC controller.
>
> Signed-off-by: Prashant Malani <pmalani@chromium.org>
> Acked-By: Benson Leung <bleung@chromium.org>
Sorry, looks like I made a typo while adding the "Acked-by" from a
previous version.
I have uploaded v3 with this fixed.
Thanks,
> ---
>
> Changes in v2:
> - Added more text to the switch descriptions, explaining their purpose,
> and relation to the Type C connector class framework.
>
> .../bindings/chrome/google,cros-ec-typec.yaml | 40 ++++++++++++++++++-
> 1 file changed, 39 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/chrome/google,cros-ec-typec.yaml b/Documentation/devicetree/bindings/chrome/google,cros-ec-typec.yaml
> index 6d7396ab8bee..800c005a0e44 100644
> --- a/Documentation/devicetree/bindings/chrome/google,cros-ec-typec.yaml
> +++ b/Documentation/devicetree/bindings/chrome/google,cros-ec-typec.yaml
> @@ -21,7 +21,34 @@ properties:
> const: google,cros-ec-typec
>
> connector:
> - $ref: /schemas/connector/usb-connector.yaml#
> + allOf:
> + - $ref: /schemas/connector/usb-connector.yaml#
> + - type: object
> + properties:
> + mode-switch:
> + description: Reference to a DT node for the USB Type C Multiplexer
> + for this connector. This switch controls the data lines routing
> + for this connector for various operation modes, including
> + Alternate Modes. This switch is assumed registered with the Type C
> + connector class framework by its driver. The Type C connector
> + class framework assumes that the mode switch property uses this
> + name.
> +
> + orientation-switch:
> + description: Reference to a DT node for the USB Type C orientation
> + switch for this connector. This switch controls routing the
> + correct data pairs depending on the cable plug orientation from
> + this connector to the USB / Alternate Mode controllers. This
> + switch is assumed registered with the Type C connector class
> + framework by its driver. The Type C connector class framework
> + assumes that the orientation switch property uses this name.
> +
> + usb-role-switch:
> + description: Reference to a DT node for the USB Data role switch
> + for this connector. This switch is assumed registered with the
> + Type C connector class framework by its driver. The Type C
> + connector class framework assumes that the USB role switch
> + property uses this name.
>
> required:
> - compatible
> @@ -49,6 +76,17 @@ examples:
> data-role = "dual";
> try-power-role = "source";
> };
> +
> + connector@1 {
> + compatible = "usb-c-connector";
> + reg = <1>;
> + power-role = "dual";
> + data-role = "host";
> + try-power-role = "source";
> + mode-switch = <&typec_mux>;
> + orientation-switch = <&typec_orientation_switch>;
> + usb-role-switch = <&typec_mux>;
> + };
> };
> };
> };
> --
> 2.26.2.761.g0e0b3e54be-goog
>
^ permalink raw reply
* Re: [PATCH 1/2] ARM: dts: imx51: Add src node interrupt
From: Shawn Guo @ 2020-05-20 1:45 UTC (permalink / raw)
To: Anson Huang
Cc: robh+dt, s.hauer, kernel, festevam, devicetree, linux-arm-kernel,
linux-kernel, Linux-imx
In-Reply-To: <1589250307-29662-1-git-send-email-Anson.Huang@nxp.com>
On Tue, May 12, 2020 at 10:25:06AM +0800, Anson Huang wrote:
> Interrupt is a required property according to SRC binding, add
> it for SRC node.
>
> Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Applied both, thanks.
^ permalink raw reply
* [PATCH v4 4/5] dt-bindings: arm: amlogic: add support for the Beelink GT-King Pro
From: Christian Hewitt @ 2020-05-20 1:43 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Kevin Hilman, devicetree,
linux-arm-kernel, linux-amlogic, linux-kernel
Cc: Christian Hewitt
In-Reply-To: <20200520014329.12469-1-christianshewitt@gmail.com>
The Shenzen AZW (Beelink) GT-King Pro is based on the Amlogic W400 reference
board with an S922X chip.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index cd7a081a4f17..db35e0d0134c 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -150,6 +150,7 @@ properties:
items:
- enum:
- azw,gtking
+ - azw,gtking-pro
- hardkernel,odroid-n2
- khadas,vim3
- ugoos,am6
--
2.17.1
^ permalink raw reply related
* [PATCH v4 3/5] arm64: dts: meson-g12b-gtking: add initial device-tree
From: Christian Hewitt @ 2020-05-20 1:43 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Kevin Hilman, devicetree,
linux-arm-kernel, linux-amlogic, linux-kernel
Cc: Christian Hewitt
In-Reply-To: <20200520014329.12469-1-christianshewitt@gmail.com>
The Shenzen AZW (Beelink) GT-King is based on the Amlogic W400 reference
board with an S922X chip.
- 4GB LPDDR4 RAM
- 64GB eMMC storage
- 10/100/1000 Base-T Ethernet
- AP6356S Wireless (802.11 a/b/g/n/ac, BT 4.1)
- HDMI 2.1 video
- S/PDIF optical output
- Analogue audio output
- 1x USB 2.0 port
- 2x USB 3.0 ports
- IR receiver
- 1x micro SD card slot
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../boot/dts/amlogic/meson-g12b-gtking.dts | 145 ++++++++++++++++++
2 files changed, 146 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index af883e0bfb9c..8c9e9dfa5da3 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts
new file mode 100644
index 000000000000..eeb7bc5539ef
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts
@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ * Copyright (c) 2019 Christian Hewitt <christianshewitt@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b-w400.dtsi"
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+ compatible = "azw,gtking", "amlogic,g12b";
+ model = "Beelink GT-King";
+
+ spdif_dit: audio-codec-1 {
+ #sound-dai-cells = <0>;
+ compatible = "linux,spdif-dit";
+ status = "okay";
+ sound-name-prefix = "DIT";
+ };
+
+ sound {
+ compatible = "amlogic,axg-sound-card";
+ model = "G12B-GTKING";
+ audio-aux-devs = <&tdmout_b>;
+ audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+ "TDMOUT_B IN 1", "FRDDR_B OUT 1",
+ "TDMOUT_B IN 2", "FRDDR_C OUT 1",
+ "TDM_B Playback", "TDMOUT_B OUT",
+ "SPDIFOUT IN 0", "FRDDR_A OUT 3",
+ "SPDIFOUT IN 1", "FRDDR_B OUT 3",
+ "SPDIFOUT IN 2", "FRDDR_C OUT 3";
+
+ assigned-clocks = <&clkc CLKID_MPLL2>,
+ <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>;
+ assigned-clock-parents = <0>, <0>, <0>;
+ assigned-clock-rates = <294912000>,
+ <270950400>,
+ <393216000>;
+ status = "okay";
+
+ dai-link-0 {
+ sound-dai = <&frddr_a>;
+ };
+
+ dai-link-1 {
+ sound-dai = <&frddr_b>;
+ };
+
+ dai-link-2 {
+ sound-dai = <&frddr_c>;
+ };
+
+ /* 8ch hdmi interface */
+ dai-link-3 {
+ sound-dai = <&tdmif_b>;
+ dai-format = "i2s";
+ dai-tdm-slot-tx-mask-0 = <1 1>;
+ dai-tdm-slot-tx-mask-1 = <1 1>;
+ dai-tdm-slot-tx-mask-2 = <1 1>;
+ dai-tdm-slot-tx-mask-3 = <1 1>;
+ mclk-fs = <256>;
+
+ codec {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+ };
+ };
+
+ /* spdif hdmi or toslink interface */
+ dai-link-4 {
+ sound-dai = <&spdifout>;
+
+ codec-0 {
+ sound-dai = <&spdif_dit>;
+ };
+
+ codec-1 {
+ sound-dai = <&tohdmitx TOHDMITX_SPDIF_IN_A>;
+ };
+ };
+
+ /* spdif hdmi interface */
+ dai-link-5 {
+ sound-dai = <&spdifout_b>;
+
+ codec {
+ sound-dai = <&tohdmitx TOHDMITX_SPDIF_IN_B>;
+ };
+ };
+
+ /* hdmi glue */
+ dai-link-6 {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+ codec {
+ sound-dai = <&hdmi_tx>;
+ };
+ };
+ };
+};
+
+&arb {
+ status = "okay";
+};
+
+&clkc_audio {
+ status = "okay";
+};
+
+&frddr_a {
+ status = "okay";
+};
+
+&frddr_b {
+ status = "okay";
+};
+
+&frddr_c {
+ status = "okay";
+};
+
+&spdifout {
+ pinctrl-0 = <&spdif_out_h_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&spdifout_b {
+ status = "okay";
+};
+
+&tdmif_b {
+ status = "okay";
+};
+
+&tdmout_b {
+ status = "okay";
+};
+
+&tohdmitx {
+ status = "okay";
+};
--
2.17.1
^ permalink raw reply related
* [PATCH v4 5/5] arm64: dts: meson-g12b-gtking-pro: add initial device-tree
From: Christian Hewitt @ 2020-05-20 1:43 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Kevin Hilman, devicetree,
linux-arm-kernel, linux-amlogic, linux-kernel
Cc: Christian Hewitt
In-Reply-To: <20200520014329.12469-1-christianshewitt@gmail.com>
The Shenzen AZW (Beelink) GT-King Pro is based on the Amlogic W400
reference board with an S922X chip.
- 4GB LPDDR4 RAM
- 64GB eMMC storage
- 10/100/1000 Base-T Ethernet
- AP6356S Wireless (802.11 a/b/g/n/ac, BT 4.1)
- HDMI 2.1 video
- Analogue audio output
- 1x RS232 port
- 2x USB 2.0 port
- 2x USB 3.0 ports
- IR receiver
- 1x micro SD card slot
- 1x Power on/off button
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../dts/amlogic/meson-g12b-gtking-pro.dts | 125 ++++++++++++++++++
2 files changed, 126 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 8c9e9dfa5da3..5cac4d1d487d 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -4,6 +4,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking-pro.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts
new file mode 100644
index 000000000000..f0c56a16af3d
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts
@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ * Copyright (c) 2019 Christian Hewitt <christianshewitt@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b-w400.dtsi"
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+ compatible = "azw,gtking", "amlogic,g12b";
+ model = "Beelink GT-King Pro";
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <100>;
+
+ power-button {
+ label = "power";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ white {
+ label = "power:white";
+ gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ sound {
+ compatible = "amlogic,axg-sound-card";
+ model = "G12B-GTKING-PRO";
+ audio-aux-devs = <&tdmout_b>;
+ audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+ "TDMOUT_B IN 1", "FRDDR_B OUT 1",
+ "TDMOUT_B IN 2", "FRDDR_C OUT 1",
+ "TDM_B Playback", "TDMOUT_B OUT";
+
+ assigned-clocks = <&clkc CLKID_MPLL2>,
+ <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>;
+ assigned-clock-parents = <0>, <0>, <0>;
+ assigned-clock-rates = <294912000>,
+ <270950400>,
+ <393216000>;
+ status = "okay";
+
+ dai-link-0 {
+ sound-dai = <&frddr_a>;
+ };
+
+ dai-link-1 {
+ sound-dai = <&frddr_b>;
+ };
+
+ dai-link-2 {
+ sound-dai = <&frddr_c>;
+ };
+
+ /* 8ch hdmi interface */
+ dai-link-3 {
+ sound-dai = <&tdmif_b>;
+ dai-format = "i2s";
+ dai-tdm-slot-tx-mask-0 = <1 1>;
+ dai-tdm-slot-tx-mask-1 = <1 1>;
+ dai-tdm-slot-tx-mask-2 = <1 1>;
+ dai-tdm-slot-tx-mask-3 = <1 1>;
+ mclk-fs = <256>;
+
+ codec {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+ };
+ };
+
+ dai-link-4 {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+ codec {
+ sound-dai = <&hdmi_tx>;
+ };
+ };
+ };
+};
+
+&arb {
+ status = "okay";
+};
+
+&clkc_audio {
+ status = "okay";
+};
+
+&frddr_a {
+ status = "okay";
+};
+
+&frddr_b {
+ status = "okay";
+};
+
+&frddr_c {
+ status = "okay";
+};
+
+&tdmif_b {
+ status = "okay";
+};
+
+&tdmout_b {
+ status = "okay";
+};
+
+&tohdmitx {
+ status = "okay";
+};
--
2.17.1
^ permalink raw reply related
* [PATCH v4 2/5] dt-bindings: arm: amlogic: add support for the Beelink GT-King
From: Christian Hewitt @ 2020-05-20 1:43 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Kevin Hilman, devicetree,
linux-arm-kernel, linux-amlogic, linux-kernel
Cc: Christian Hewitt
In-Reply-To: <20200520014329.12469-1-christianshewitt@gmail.com>
The Shenzen AZW (Beelink) GT-King is based on the Amlogic W400 reference
board with an S922X chip.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index 47badda69ef5..cd7a081a4f17 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -149,6 +149,7 @@ properties:
- description: Boards with the Amlogic Meson G12B S922X SoC
items:
- enum:
+ - azw,gtking
- hardkernel,odroid-n2
- khadas,vim3
- ugoos,am6
--
2.17.1
^ permalink raw reply related
* [PATCH v4 1/5] arm64: dts: meson: convert ugoos-am6 to common w400 dtsi
From: Christian Hewitt @ 2020-05-20 1:43 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Kevin Hilman, devicetree,
linux-arm-kernel, linux-amlogic, linux-kernel
Cc: Christian Hewitt
In-Reply-To: <20200520014329.12469-1-christianshewitt@gmail.com>
Convert the Ugoos AM6 dts into meson-g12b-w400.dtsi, and then create
a new AM6 dts that references it. This is in preparation for several
new G12B devices that will share the common w400 dtsi.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
.../boot/dts/amlogic/meson-g12b-ugoos-am6.dts | 375 +---------------
.../boot/dts/amlogic/meson-g12b-w400.dtsi | 423 ++++++++++++++++++
2 files changed, 424 insertions(+), 374 deletions(-)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-ugoos-am6.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-ugoos-am6.dts
index de257c1b6d9d..a8331330011a 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-ugoos-am6.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-ugoos-am6.dts
@@ -7,42 +7,13 @@
/dts-v1/;
-#include "meson-g12b.dtsi"
-#include "meson-g12b-s922x.dtsi"
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include "meson-g12b-w400.dtsi"
#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
/ {
compatible = "ugoos,am6", "amlogic,s922x", "amlogic,g12b";
model = "Ugoos AM6";
- aliases {
- serial0 = &uart_AO;
- ethernet0 = ðmac;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- memory@0 {
- device_type = "memory";
- reg = <0x0 0x0 0x0 0x40000000>;
- };
-
- emmc_pwrseq: emmc-pwrseq {
- compatible = "mmc-pwrseq-emmc";
- reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
- };
-
- sdio_pwrseq: sdio-pwrseq {
- compatible = "mmc-pwrseq-simple";
- reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
- clocks = <&wifi32k>;
- clock-names = "ext_clock";
- };
-
spdif_dit: audio-codec-1 {
#sound-dai-cells = <0>;
compatible = "linux,spdif-dit";
@@ -50,154 +21,6 @@
sound-name-prefix = "DIT";
};
- flash_1v8: regulator-flash_1v8 {
- compatible = "regulator-fixed";
- regulator-name = "FLASH_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- vin-supply = <&vcc_3v3>;
- regulator-always-on;
- };
-
- main_12v: regulator-main_12v {
- compatible = "regulator-fixed";
- regulator-name = "12V";
- regulator-min-microvolt = <12000000>;
- regulator-max-microvolt = <12000000>;
- regulator-always-on;
- };
-
- vcc_5v: regulator-vcc_5v {
- compatible = "regulator-fixed";
- regulator-name = "VCC_5V";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- vin-supply = <&main_12v>;
-
- gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
- enable-active-high;
- };
-
- vcc_1v8: regulator-vcc_1v8 {
- compatible = "regulator-fixed";
- regulator-name = "VCC_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- vin-supply = <&vcc_3v3>;
- regulator-always-on;
- };
-
- vcc_3v3: regulator-vcc_3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VCC_3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- vin-supply = <&vddao_3v3>;
- regulator-always-on;
- /* FIXME: actually controlled by VDDCPU_B_EN */
- };
-
- vddcpu_a: regulator-vddcpu-a {
- /*
- * MP1653 Regulator.
- */
- compatible = "pwm-regulator";
-
- regulator-name = "VDDCPU_A";
- regulator-min-microvolt = <721000>;
- regulator-max-microvolt = <1022000>;
-
- vin-supply = <&main_12v>;
-
- pwms = <&pwm_ab 0 1250 0>;
- pwm-dutycycle-range = <100 0>;
-
- regulator-boot-on;
- regulator-always-on;
- };
-
- vddcpu_b: regulator-vddcpu-b {
- /*
- * MP1652 Regulator.
- */
- compatible = "pwm-regulator";
-
- regulator-name = "VDDCPU_B";
- regulator-min-microvolt = <721000>;
- regulator-max-microvolt = <1022000>;
-
- vin-supply = <&main_12v>;
-
- pwms = <&pwm_AO_cd 1 1250 0>;
- pwm-dutycycle-range = <100 0>;
-
- regulator-boot-on;
- regulator-always-on;
- };
-
- usb1_pow: regulator-usb1-pow {
- compatible = "regulator-fixed";
- regulator-name = "USB1_POW";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- vin-supply = <&vcc_5v>;
-
- /* connected to SY6280A Power Switch */
- gpio = <&gpio GPIOA_8 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- usb_pwr_en: regulator-usb-pwr-en {
- compatible = "regulator-fixed";
- regulator-name = "USB_PWR_EN";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- vin-supply = <&vcc_5v>;
-
- /* Connected to USB3 Type-A Port power enable */
- gpio = <&gpio GPIOAO_7 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vddao_1v8: regulator-vddao-1v8 {
- compatible = "regulator-fixed";
- regulator-name = "VDDAO_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- vin-supply = <&vddao_3v3>;
- regulator-always-on;
- };
-
- vddao_3v3: regulator-vddao-3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VDDAO_3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- vin-supply = <&main_12v>;
- regulator-always-on;
- };
-
- cvbs-connector {
- compatible = "composite-video-connector";
-
- port {
- cvbs_connector_in: endpoint {
- remote-endpoint = <&cvbs_vdac_out>;
- };
- };
- };
-
- hdmi-connector {
- compatible = "hdmi-connector";
- type = "a";
-
- port {
- hdmi_connector_in: endpoint {
- remote-endpoint = <&hdmi_tx_tmds_out>;
- };
- };
- };
-
sound {
compatible = "amlogic,axg-sound-card";
model = "G12B-UGOOS-AM6";
@@ -277,110 +100,16 @@
};
};
};
-
- wifi32k: wifi32k {
- compatible = "pwm-clock";
- #clock-cells = <0>;
- clock-frequency = <32768>;
- pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
- };
};
&arb {
status = "okay";
};
-&cec_AO {
- pinctrl-0 = <&cec_ao_a_h_pins>;
- pinctrl-names = "default";
- status = "disabled";
- hdmi-phandle = <&hdmi_tx>;
-};
-
-&cecb_AO {
- pinctrl-0 = <&cec_ao_b_h_pins>;
- pinctrl-names = "default";
- status = "okay";
- hdmi-phandle = <&hdmi_tx>;
-};
-
&clkc_audio {
status = "okay";
};
-&cpu0 {
- cpu-supply = <&vddcpu_b>;
- operating-points-v2 = <&cpu_opp_table_0>;
- clocks = <&clkc CLKID_CPU_CLK>;
- clock-latency = <50000>;
-};
-
-&cpu1 {
- cpu-supply = <&vddcpu_b>;
- operating-points-v2 = <&cpu_opp_table_0>;
- clocks = <&clkc CLKID_CPU_CLK>;
- clock-latency = <50000>;
-};
-
-&cpu100 {
- cpu-supply = <&vddcpu_a>;
- operating-points-v2 = <&cpub_opp_table_1>;
- clocks = <&clkc CLKID_CPUB_CLK>;
- clock-latency = <50000>;
-};
-
-&cpu101 {
- cpu-supply = <&vddcpu_a>;
- operating-points-v2 = <&cpub_opp_table_1>;
- clocks = <&clkc CLKID_CPUB_CLK>;
- clock-latency = <50000>;
-};
-
-&cpu102 {
- cpu-supply = <&vddcpu_a>;
- operating-points-v2 = <&cpub_opp_table_1>;
- clocks = <&clkc CLKID_CPUB_CLK>;
- clock-latency = <50000>;
-};
-
-&cpu103 {
- cpu-supply = <&vddcpu_a>;
- operating-points-v2 = <&cpub_opp_table_1>;
- clocks = <&clkc CLKID_CPUB_CLK>;
- clock-latency = <50000>;
-};
-
-&cvbs_vdac_port {
- cvbs_vdac_out: endpoint {
- remote-endpoint = <&cvbs_connector_in>;
- };
-};
-
-&ext_mdio {
- external_phy: ethernet-phy@0 {
- /* Realtek RTL8211F (0x001cc916) */
- reg = <0>;
- max-speed = <1000>;
-
- reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
- reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
-
- interrupt-parent = <&gpio_intc>;
- /* MAC_INTR on GPIOZ_14 */
- interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
- };
-};
-
-ðmac {
- pinctrl-0 = <ð_pins>, <ð_rgmii_pins>;
- pinctrl-names = "default";
- status = "okay";
- phy-mode = "rgmii";
- phy-handle = <&external_phy>;
- amlogic,tx-delay-ns = <2>;
-};
-
&frddr_a {
status = "okay";
};
@@ -393,112 +122,10 @@
status = "okay";
};
-&hdmi_tx {
- status = "okay";
- pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
- pinctrl-names = "default";
- hdmi-supply = <&vcc_5v>;
-};
-
-&hdmi_tx_tmds_port {
- hdmi_tx_tmds_out: endpoint {
- remote-endpoint = <&hdmi_connector_in>;
- };
-};
-
&ir {
- status = "okay";
- pinctrl-0 = <&remote_input_ao_pins>;
- pinctrl-names = "default";
linux,rc-map-name = "rc-khadas";
};
-&pwm_ab {
- pinctrl-0 = <&pwm_a_e_pins>;
- pinctrl-names = "default";
- clocks = <&xtal>;
- clock-names = "clkin0";
- status = "okay";
-};
-
-&pwm_AO_cd {
- pinctrl-0 = <&pwm_ao_d_e_pins>;
- pinctrl-names = "default";
- clocks = <&xtal>;
- clock-names = "clkin1";
- status = "okay";
-};
-
-&pwm_ef {
- pinctrl-0 = <&pwm_e_pins>;
- pinctrl-names = "default";
- clocks = <&xtal>;
- clock-names = "clkin0";
- status = "okay";
-};
-
-/* SDIO */
-&sd_emmc_a {
- status = "okay";
- pinctrl-0 = <&sdio_pins>;
- pinctrl-1 = <&sdio_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
- #address-cells = <1>;
- #size-cells = <0>;
-
- bus-width = <4>;
- cap-sd-highspeed;
- sd-uhs-sdr50;
- max-frequency = <100000000>;
-
- non-removable;
- disable-wp;
-
- mmc-pwrseq = <&sdio_pwrseq>;
-
- vmmc-supply = <&vddao_3v3>;
- vqmmc-supply = <&vddao_1v8>;
-
- brcmf: wifi@1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
- };
-};
-
-/* SD card */
-&sd_emmc_b {
- status = "okay";
- pinctrl-0 = <&sdcard_c_pins>;
- pinctrl-1 = <&sdcard_clk_gate_c_pins>;
- pinctrl-names = "default", "clk-gate";
-
- bus-width = <4>;
- cap-sd-highspeed;
- max-frequency = <50000000>;
- disable-wp;
-
- cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
- vmmc-supply = <&vddao_3v3>;
- vqmmc-supply = <&vddao_3v3>;
-};
-
-/* eMMC */
-&sd_emmc_c {
- status = "okay";
- pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
- pinctrl-1 = <&emmc_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
-
- bus-width = <8>;
- cap-mmc-highspeed;
- max-frequency = <100000000>;
- disable-wp;
-
- mmc-pwrseq = <&emmc_pwrseq>;
- vmmc-supply = <&vcc_3v3>;
- vqmmc-supply = <&flash_1v8>;
-};
-
&spdifout {
pinctrl-0 = <&spdif_out_h_pins>;
pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi
new file mode 100644
index 000000000000..98b70d216a6f
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi
@@ -0,0 +1,423 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ * Copyright (c) 2019 Christian Hewitt <christianshewitt@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b.dtsi"
+#include "meson-g12b-s922x.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+
+/ {
+ aliases {
+ serial0 = &uart_AO;
+ ethernet0 = ðmac;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
+
+ flash_1v8: regulator-flash_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "FLASH_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ main_12v: regulator-main_12v {
+ compatible = "regulator-fixed";
+ regulator-name = "12V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ };
+
+ vcc_5v: regulator-vcc_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&main_12v>;
+
+ gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
+ enable-active-high;
+ };
+
+ vcc_1v8: regulator-vcc_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ /* FIXME: actually controlled by VDDCPU_B_EN */
+ };
+
+ vddcpu_a: regulator-vddcpu-a {
+ /*
+ * MP1653 Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU_A";
+ regulator-min-microvolt = <721000>;
+ regulator-max-microvolt = <1022000>;
+
+ vin-supply = <&main_12v>;
+
+ pwms = <&pwm_ab 0 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vddcpu_b: regulator-vddcpu-b {
+ /*
+ * MP1652 Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU_B";
+ regulator-min-microvolt = <721000>;
+ regulator-max-microvolt = <1022000>;
+
+ vin-supply = <&main_12v>;
+
+ pwms = <&pwm_AO_cd 1 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ usb1_pow: regulator-usb1-pow {
+ compatible = "regulator-fixed";
+ regulator-name = "USB1_POW";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v>;
+
+ /* connected to SY6280A Power Switch */
+ gpio = <&gpio GPIOA_8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ usb_pwr_en: regulator-usb-pwr-en {
+ compatible = "regulator-fixed";
+ regulator-name = "USB_PWR_EN";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v>;
+
+ /* Connected to USB3 Type-A Port power enable */
+ gpio = <&gpio GPIOAO_7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vddao_1v8: regulator-vddao-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&main_12v>;
+ regulator-always-on;
+ };
+
+ cvbs-connector {
+ compatible = "composite-video-connector";
+
+ port {
+ cvbs_connector_in: endpoint {
+ remote-endpoint = <&cvbs_vdac_out>;
+ };
+ };
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+
+ wifi32k: wifi32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+ };
+};
+
+&cec_AO {
+ pinctrl-0 = <&cec_ao_a_h_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+ pinctrl-0 = <&cec_ao_b_h_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&cpu0 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu100 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu101 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu102 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu103 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cvbs_vdac_port {
+ cvbs_vdac_out: endpoint {
+ remote-endpoint = <&cvbs_connector_in>;
+ };
+};
+
+&ext_mdio {
+ external_phy: ethernet-phy@0 {
+ /* Realtek RTL8211F (0x001cc916) */
+ reg = <0>;
+ max-speed = <1000>;
+
+ reset-assert-us = <10000>;
+ reset-deassert-us = <30000>;
+ reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+
+ interrupt-parent = <&gpio_intc>;
+ /* MAC_INTR on GPIOZ_14 */
+ interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+ðmac {
+ pinctrl-0 = <ð_pins>, <ð_rgmii_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ phy-mode = "rgmii";
+ phy-handle = <&external_phy>;
+ amlogic,tx-delay-ns = <2>;
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+ pinctrl-names = "default";
+ hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
+&ir {
+ status = "okay";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+};
+
+&pwm_ab {
+ pinctrl-0 = <&pwm_a_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin0";
+ status = "okay";
+};
+
+&pwm_AO_cd {
+ pinctrl-0 = <&pwm_ao_d_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin1";
+ status = "okay";
+};
+
+&pwm_ef {
+ pinctrl-0 = <&pwm_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin0";
+ status = "okay";
+};
+
+/* SDIO */
+&sd_emmc_a {
+ status = "okay";
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ sd-uhs-sdr50;
+ max-frequency = <100000000>;
+
+ non-removable;
+ disable-wp;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddao_1v8>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_c_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddao_3v3>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ max-frequency = <100000000>;
+ disable-wp;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&flash_1v8>;
+};
+
+&uart_A {
+ status = "okay";
+ pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+ max-speed = <2000000>;
+ clocks = <&wifi32k>;
+ clock-names = "lpo";
+ };
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+ dr_mode = "host";
+ vbus-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy0 {
+ phy-supply = <&usb1_pow>;
+};
+
+&usb2_phy1 {
+ phy-supply = <&usb1_pow>;
+};
--
2.17.1
^ permalink raw reply related
* [PATCH v4 0/5] arm64: dts: meson: add W400 dtsi and GT-King/Pro devices
From: Christian Hewitt @ 2020-05-20 1:43 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Kevin Hilman, devicetree,
linux-arm-kernel, linux-amlogic, linux-kernel
Cc: Christian Hewitt
This series combines patch 2 from [1] which converts the existing Ugoos
AM6 device-tree to a common W400 dtsi and dts, and then reworks the
Beelink GT-King/GT-King Pro series from [2] to use the dtsi, but this
time without the offending common audio dtsi approach. I've carried
forwards acks on bindings from Rob as these did not change.
v4 - rebased against Kevin's v5.8/dt64 branch
v3 - amend author full-name on bindings patch
[1] https://patchwork.kernel.org/patch/11497105/
[2] https://patchwork.kernel.org/project/linux-amlogic/list/?series=273483
Christian Hewitt (5):
arm64: dts: meson: convert ugoos-am6 to common w400 dtsi
dt-bindings: arm: amlogic: add support for the Beelink GT-King
arm64: dts: meson-g12b-gtking: add initial device-tree
dt-bindings: arm: amlogic: add support for the Beelink GT-King Pro
arm64: dts: meson-g12b-gtking-pro: add initial device-tree
.../devicetree/bindings/arm/amlogic.yaml | 2 +
arch/arm64/boot/dts/amlogic/Makefile | 2 +
.../dts/amlogic/meson-g12b-gtking-pro.dts | 125 ++++++
.../boot/dts/amlogic/meson-g12b-gtking.dts | 145 ++++++
.../boot/dts/amlogic/meson-g12b-ugoos-am6.dts | 375 +---------------
.../boot/dts/amlogic/meson-g12b-w400.dtsi | 423 ++++++++++++++++++
6 files changed, 698 insertions(+), 374 deletions(-)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi
--
2.17.1
^ permalink raw reply
* Re: [PATCH 1/2] arm64: dts: imx8mq: Add src node interrupts
From: Shawn Guo @ 2020-05-20 1:32 UTC (permalink / raw)
To: Anson Huang
Cc: robh+dt, s.hauer, kernel, festevam, horia.geanta, peng.fan,
l.stach, agx, leonard.crestez, andrew.smirnov, jun.li, devicetree,
linux-arm-kernel, linux-kernel, Linux-imx
In-Reply-To: <1589012271-12740-1-git-send-email-Anson.Huang@nxp.com>
On Sat, May 09, 2020 at 04:17:50PM +0800, Anson Huang wrote:
> Interrupts is a required property according to SRC binding, add
> it for SRC node.
>
> Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Applied both, thanks.
^ permalink raw reply
* Re: [PATCH V3 00/10] clk: imx: fixes and improve for i.MX8M
From: Shawn Guo @ 2020-05-20 1:27 UTC (permalink / raw)
To: peng.fan
Cc: s.hauer, leonard.crestez, abel.vesa, aisheng.dong, kernel,
festevam, linux-imx, Anson.Huang, linux-arm-kernel, linux-kernel,
linux-clk, devicetree
In-Reply-To: <1588830979-11586-1-git-send-email-peng.fan@nxp.com>
On Thu, May 07, 2020 at 01:56:09PM +0800, peng.fan@nxp.com wrote:
> From: Peng Fan <peng.fan@nxp.com>
>
> Patches rebased on for-next
>
> V3:
> Add R-b tag for patch 1-6,10
> Use clk_mux_ops in patch 7, explain more details in commit log
> Boot test on i.MX8MM/N/MQ/P
>
> V2:
> Patch 7, drop wait after write, add one line comment for write twice
>
> V1:
> Patch 1,2 is to fix the lockdep warning reported by Leonard
> Patch 3 is to fix pll mux bit
> Patch 4 is align with other i.MX8M using gate
> Patch 5 is to simplify i.MX8MP clk root using composite
>
> Patch 3~5 is actually https://patchwork.kernel.org/patch/11402761/
> with a minimal change to patch 5 here.
>
> Patch 6 is to use composite core clk for A53 clk root
> Patch 7,8,9 is actually to fix CORE/BUS clk slice issue.
> This issue is triggerred after we update U-Boot to include
> the A53 clk fixes to sources from PLL, not from A53 root clk,
> because of the signoff timing is 1GHz. U-Boot set the A53 root
> mux to 2, sys pll2 500MHz. Kernel will set the A53 root mux to
> 4, sys pll1 800MHz, then gate off sys pll2 500MHz. Then kernel
> will gate off A53 root because clk_ignore_unsed, A53 directly sources
> PLL, so it is ok to gate off A53 root. However when gate off A53
> root clk, system hang, because the original mux sys pll2 500MHz
> gated off with CLK_OPS_PARENT_ENABLE flag.
>
> It is lucky that we not met issue for other core/bus clk slice
> except A53 ROOT core slice. But it is always triggerred after
> U-Boot and Linux both switch to use ARM PLL for A53 core, but
> have different mux settings for A53 root clk slice.
>
> So the three patches is to address this issue.
>
> Patch 10 is make memrepair as critical.
>
> Peng Fan (10):
> arm64: dts: imx8m: assign clocks for A53
> clk: imx8m: drop clk_hw_set_parent for A53
> clk: imx: imx8mp: fix pll mux bit
> clk: imx8mp: Define gates for pll1/2 fixed dividers
> clk: imx8mp: use imx8m_clk_hw_composite_core to simplify code
> clk: imx8m: migrate A53 clk root to use composite core
> clk: imx: add mux ops for i.MX8M composite clk
> clk: imx: add imx8m_clk_hw_composite_bus
> clk: imx: use imx8m_clk_hw_composite_bus for i.MX8M bus clk slice
Applied 1 ~ 9, thanks.
> clk: imx8mp: mark memrepair clock as critical
^ permalink raw reply
* Re: [PATCH] arm64: dts: freescale: sl28: enable LPUART1
From: Shawn Guo @ 2020-05-20 1:14 UTC (permalink / raw)
To: Michael Walle
Cc: linux-kernel, devicetree, linux-arm-kernel, Li Yang, Rob Herring
In-Reply-To: <20200505150037.32573-1-michael@walle.cc>
On Tue, May 05, 2020 at 05:00:37PM +0200, Michael Walle wrote:
> Now that the LPUART has support for the LS1028A SoC, also enable it on
> our board.
>
> Signed-off-by: Michael Walle <michael@walle.cc>
> ---
>
> Hi Shawn,
>
> After adding/fixing the LPUART support for the LS1028A I've forgot to send
> this patch to actually enable the LPUART on our boards. It would be great
> if this could make it into the fixes queue for the -rc. If not its also ok.
We only take critical bug fixes at this point. Applied it for -next.
Shawn
^ permalink raw reply
* Re: [PATCH] arm64: dts: imx8mm: Add node for SPDIF
From: Shawn Guo @ 2020-05-20 1:05 UTC (permalink / raw)
To: Adam Ford
Cc: linux-arm-kernel, aford, Rob Herring, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team,
devicetree, linux-kernel
In-Reply-To: <20200502132011.196045-1-aford173@gmail.com>
On Sat, May 02, 2020 at 08:20:11AM -0500, Adam Ford wrote:
> The i.MX8M Mini can support SPIDF which is very similar to the
> IP used on the i.MX35.
>
> This patch adds the SPIF node.
>
> Signed-off-by: Adam Ford <aford173@gmail.com>
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> index d46e727fc362..00aad55ece65 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> @@ -358,6 +358,29 @@ micfil: micfil@30080000 {
> status = "disabled";
> };
>
> + spdif1: spdif@30090000 {
It should be in a patch series with previous micfil one, as it cannot be
applied independently.
> + compatible = "fsl,imx8mm-spdif", "fsl,imx35-spdif";
> + reg = <0x30090000 0x10000>;
> + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk IMX8MM_CLK_AUDIO_AHB>, /* core */
> + <&clk IMX8MM_CLK_24M>, /* rxtx0 */
> + <&clk IMX8MM_CLK_SPDIF1>, /* rxtx1 */
> + <&clk IMX8MM_CLK_DUMMY>, /* rxtx2 */
> + <&clk IMX8MM_CLK_DUMMY>, /* rxtx3 */
> + <&clk IMX8MM_CLK_DUMMY>, /* rxtx4 */
> + <&clk IMX8MM_CLK_AUDIO_AHB>, /* rxtx5 */
> + <&clk IMX8MM_CLK_DUMMY>, /* rxtx6 */
> + <&clk IMX8MM_CLK_DUMMY>, /* rxtx7 */
> + <&clk IMX8MM_CLK_DUMMY>; /* spba */
> + clock-names = "core", "rxtx0",
> + "rxtx1", "rxtx2",
> + "rxtx3", "rxtx4",
> + "rxtx5", "rxtx6",
> + "rxtx7", "spba";
> + dmas = <&sdma2 28 18 0>, <&sdma2 29 18 0>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
Have a newline between nodes.
Shawn
> gpio1: gpio@30200000 {
> compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio";
> reg = <0x30200000 0x10000>;
> --
> 2.25.1
>
^ permalink raw reply
* Re: [PATCH] arm64: dts: imx8mm: Add support for micfil
From: Shawn Guo @ 2020-05-20 1:03 UTC (permalink / raw)
To: Adam Ford
Cc: linux-arm-kernel, aford, Rob Herring, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team,
Catalin Marinas, Will Deacon, devicetree, linux-kernel
In-Reply-To: <20200502125949.194032-2-aford173@gmail.com>
On Sat, May 02, 2020 at 07:59:48AM -0500, Adam Ford wrote:
> The i.MX8M Mini has supports the MICFIL digital interface.
> It's a 16-bit audio signal from a PDM microphone bitstream.
> The driver is already in the kernel, but the node is missing.
>
> This patch adds the micfil node.
>
> Signed-off-by: Adam Ford <aford173@gmail.com>
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> index c63685ae80ee..d46e727fc362 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> @@ -339,6 +339,25 @@ sai6: sai@30060000 {
> status = "disabled";
> };
>
> + micfil: micfil@30080000 {
Find a generic node name, audio-controller maybe?
Shawn
> + compatible = "fsl,imx8mm-micfil";
> + reg = <0x30080000 0x10000>;
> + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk IMX8MM_CLK_PDM_IPG>,
> + <&clk IMX8MM_CLK_PDM_ROOT>,
> + <&clk IMX8MM_AUDIO_PLL1_OUT>,
> + <&clk IMX8MM_AUDIO_PLL2_OUT>,
> + <&clk IMX8MM_CLK_EXT3>;
> + clock-names = "ipg_clk", "ipg_clk_app",
> + "pll8k", "pll11k", "clkext3";
> + dmas = <&sdma2 24 25 0x80000000>;
> + dma-names = "rx";
> + status = "disabled";
> + };
> +
> gpio1: gpio@30200000 {
> compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio";
> reg = <0x30200000 0x10000>;
> --
> 2.25.1
>
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox