* [PATCH net-next v4 1/2] dt-bindings: net: ti: k3-am654-cpsw-nuss: Add ti,j722s-cpsw-nuss compatible
From: Nora Schiffer @ 2026-04-07 10:48 UTC (permalink / raw)
To: Andrew Lunn, David S. Miller, Eric Dumazet, Jakub Kicinski,
Paolo Abeni
Cc: Nishanth Menon, Vignesh Raghavendra, Tero Kristo,
Siddharth Vadapalli, Roger Quadros, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, netdev, devicetree,
linux-kernel, linux-arm-kernel, linux, Nora Schiffer
The J722S CPSW3G is mostly identical to the AM64's, but additionally
supports SGMII. The AM64 compatible ti,am642-cpsw-nuss is used as a
fallback.
Signed-off-by: Nora Schiffer <nora.schiffer@ew.tq-group.com>
---
v2: keep ti,am642-cpsw-nuss as a fallback
v3: resubmission for net-next, no changes
v4: remove redundant items: level
.../bindings/net/ti,k3-am654-cpsw-nuss.yaml | 19 ++++++++++++-------
1 file changed, 12 insertions(+), 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml b/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml
index a959c1d7e643a..c409c6310ed40 100644
--- a/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml
+++ b/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml
@@ -53,13 +53,18 @@ properties:
"#size-cells": true
compatible:
- enum:
- - ti,am642-cpsw-nuss
- - ti,am654-cpsw-nuss
- - ti,j7200-cpswxg-nuss
- - ti,j721e-cpsw-nuss
- - ti,j721e-cpswxg-nuss
- - ti,j784s4-cpswxg-nuss
+ oneOf:
+ - enum:
+ - ti,am642-cpsw-nuss
+ - ti,am654-cpsw-nuss
+ - ti,j7200-cpswxg-nuss
+ - ti,j721e-cpsw-nuss
+ - ti,j721e-cpswxg-nuss
+ - ti,j784s4-cpswxg-nuss
+ - items:
+ - enum:
+ - ti,j722s-cpsw-nuss
+ - const: ti,am642-cpsw-nuss
reg:
maxItems: 1
--
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
https://www.tq-group.com/
^ permalink raw reply related
* [PATCH net-next v4 2/2] net: ethernet: ti: am65-cpsw: add support for J722S SoC family
From: Nora Schiffer @ 2026-04-07 10:48 UTC (permalink / raw)
To: Andrew Lunn, David S. Miller, Eric Dumazet, Jakub Kicinski,
Paolo Abeni
Cc: Nishanth Menon, Vignesh Raghavendra, Tero Kristo,
Siddharth Vadapalli, Roger Quadros, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, netdev, devicetree,
linux-kernel, linux-arm-kernel, linux, Nora Schiffer
In-Reply-To: <191e9f7e3a6c14eabe891a98c5fb646766479c0a.1775558273.git.nora.schiffer@ew.tq-group.com>
The J722S CPSW3G is mostly identical to the AM64's, but additionally
supports SGMII.
Signed-off-by: Nora Schiffer <nora.schiffer@ew.tq-group.com>
---
v2: drop AM64_CPSW_QUIRK_CUT_THRU flag, which is a downstream ti-linux feature
v3: resubmission for net-next, no changes
v4: no changes
SGMII operation also requires changes to the phy-j721e-wiz and gmii-sel drivers:
https://lore.kernel.org/lkml/cover.1775045279.git.nora.schiffer@ew.tq-group.com/
drivers/net/ethernet/ti/am65-cpsw-nuss.c | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/drivers/net/ethernet/ti/am65-cpsw-nuss.c b/drivers/net/ethernet/ti/am65-cpsw-nuss.c
index d9400599e80a4..7ac75fc8cdcf4 100644
--- a/drivers/net/ethernet/ti/am65-cpsw-nuss.c
+++ b/drivers/net/ethernet/ti/am65-cpsw-nuss.c
@@ -3468,6 +3468,13 @@ static const struct am65_cpsw_pdata am64x_cpswxg_pdata = {
.fdqring_mode = K3_RINGACC_RING_MODE_RING,
};
+static const struct am65_cpsw_pdata j722s_cpswxg_pdata = {
+ .quirks = AM64_CPSW_QUIRK_DMA_RX_TDOWN_IRQ,
+ .ale_dev_id = "am64-cpswxg",
+ .fdqring_mode = K3_RINGACC_RING_MODE_RING,
+ .extra_modes = BIT(PHY_INTERFACE_MODE_SGMII),
+};
+
static const struct am65_cpsw_pdata j7200_cpswxg_pdata = {
.quirks = 0,
.ale_dev_id = "am64-cpswxg",
@@ -3495,6 +3502,7 @@ static const struct of_device_id am65_cpsw_nuss_of_mtable[] = {
{ .compatible = "ti,am654-cpsw-nuss", .data = &am65x_sr1_0},
{ .compatible = "ti,j721e-cpsw-nuss", .data = &j721e_pdata},
{ .compatible = "ti,am642-cpsw-nuss", .data = &am64x_cpswxg_pdata},
+ { .compatible = "ti,j722s-cpsw-nuss", .data = &j722s_cpswxg_pdata},
{ .compatible = "ti,j7200-cpswxg-nuss", .data = &j7200_cpswxg_pdata},
{ .compatible = "ti,j721e-cpswxg-nuss", .data = &j721e_cpswxg_pdata},
{ .compatible = "ti,j784s4-cpswxg-nuss", .data = &j784s4_cpswxg_pdata},
--
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
https://www.tq-group.com/
^ permalink raw reply related
* Re: [PATCH 1/2] arm64: dts: qcom: kodiak: Add iface clock for ice sdhc
From: Kuldeep Singh @ 2026-04-07 11:09 UTC (permalink / raw)
To: Konrad Dybcio, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel
In-Reply-To: <8ea92c00-56ca-47cd-95aa-dbf49ecf4118@oss.qualcomm.com>
>> diff --git a/arch/arm64/boot/dts/qcom/kodiak.dtsi b/arch/arm64/boot/dts/qcom/kodiak.dtsi
>> index dda4697a61b7..5e6b659e8719 100644
>> --- a/arch/arm64/boot/dts/qcom/kodiak.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/kodiak.dtsi
>> @@ -1082,7 +1082,8 @@ sdhc_ice: crypto@7c8000 {
>> compatible = "qcom,sc7280-inline-crypto-engine",
>> "qcom,inline-crypto-engine";
>> reg = <0x0 0x007c8000 0x0 0x18000>;
>> - clocks = <&gcc GCC_SDCC1_ICE_CORE_CLK>;
>> + clocks = <&gcc GCC_SDCC1_ICE_CORE_CLK>, <&gcc GCC_SDCC1_AHB_CLK>;
>> + clock-names = "core", "iface";
>
> nit: one a line would be preferred, please fix that up as you seemingly
> need a v2 anyway
Hi Konrad, Didn't get your comment completely.
Do I need to send v2 to just fix clock entries in 2 lines?
Or some other comment to address and send v2 for that?
I don't see any other comment on patchset to address.
Kindly clarify.
--
Regards
Kuldeep
^ permalink raw reply
* Re: [PATCH 1/5] arm64: dts: qcom: sm8550: add PCIe MHI register regions and port labels
From: Konrad Dybcio @ 2026-04-07 11:05 UTC (permalink / raw)
To: jsandom, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel
In-Reply-To: <20260404-rb5gen2-dts-v1-1-895f8fc494fc@axon.com>
On 4/4/26 11:50 AM, Joe Sandom via B4 Relay wrote:
> From: Joe Sandom <jsandom@axon.com>
>
> Add the MHI register regions to the pcie0 and pcie1 controller nodes
> so that the MHI bus layer can access controller registers directly.
>
> Also add labels to the root port nodes (pcie0_port0, pcie1_port0) to
> allow board DTS files to reference them for adding endpoint devices
> to each pcie root port.
>
> Signed-off-by: Joe Sandom <jsandom@axon.com>
> ---
> arch/arm64/boot/dts/qcom/sm8550.dtsi | 14 ++++++++------
> 1 file changed, 8 insertions(+), 6 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
> index 912525e9bca6f5e1cbb8887ee0bf9e39650dc4ff..d4caf4d00832d7f1e8f65bf2bc873cddadc42168 100644
> --- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
> @@ -1964,8 +1964,9 @@ pcie0: pcie@1c00000 {
> <0 0x60000000 0 0xf1d>,
> <0 0x60000f20 0 0xa8>,
> <0 0x60001000 0 0x1000>,
> - <0 0x60100000 0 0x100000>;
> - reg-names = "parf", "dbi", "elbi", "atu", "config";
> + <0 0x60100000 0 0x100000>,
> + <0 0x01C03000 0 0x1000>;
lowercase hex please, both places
> + reg-names = "parf", "dbi", "elbi", "atu", "config", "mhi";
Since you're touching this part of the file anyway and others asked for
more changes.. could you please break up the reg-names that you're
editing such that there's one entry per line and they're aligned on
the opening quote, i.e.
reg-names = "foo",
"bar",
...
?
FWIW the reg ranges you added are OK
Konrad
^ permalink raw reply
* Re: [PATCH v2 2/2] interconnect: qcom: add Hawi interconnect provider driver
From: Konrad Dybcio @ 2026-04-07 10:54 UTC (permalink / raw)
To: Vivek Aknurwar, Georgi Djakov, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, linux-pm, devicetree, linux-kernel, Mike Tipton,
Krzysztof Kozlowski
In-Reply-To: <20260406-icc-hawi-v2-2-6cfee87a1d25@oss.qualcomm.com>
On 4/7/26 1:04 AM, Vivek Aknurwar wrote:
> Add driver for the Qualcomm interconnect buses found in Hawi
> based platforms. The topology consists of several NoCs that are
> controlled by a remote processor that collects the aggregated
> bandwidth for each master-slave pair.
>
> Signed-off-by: Vivek Aknurwar <vivek.aknurwar@oss.qualcomm.com>
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
> ---
You lost my and Dmitry's r-bs from v1
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Konrad
^ permalink raw reply
* Re: [PATCH 04/19] dt-bindings: display/panel: ilitek,ili9881c: describe Waveshare panel
From: Krzysztof Kozlowski @ 2026-04-07 10:46 UTC (permalink / raw)
To: Dmitry Baryshkov, Neil Armstrong, Jessica Zhang, David Airlie,
Simona Vetter, Maarten Lankhorst, Maxime Ripard,
Thomas Zimmermann, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Cong Yang, Ondrej Jirman, Javier Martinez Canillas, Jagan Teki,
Liam Girdwood, Mark Brown, Linus Walleij, Bartosz Golaszewski
Cc: dri-devel, devicetree, linux-kernel, linux-gpio
In-Reply-To: <20260401-waveshare-dsi-touch-v1-4-5e9119b5a014@oss.qualcomm.com>
On 01/04/2026 09:26, Dmitry Baryshkov wrote:
>
> diff --git a/Documentation/devicetree/bindings/display/panel/ilitek,ili9881c.yaml b/Documentation/devicetree/bindings/display/panel/ilitek,ili9881c.yaml
> index d979701a00a8..42e35986fbf6 100644
> --- a/Documentation/devicetree/bindings/display/panel/ilitek,ili9881c.yaml
> +++ b/Documentation/devicetree/bindings/display/panel/ilitek,ili9881c.yaml
> @@ -24,6 +24,7 @@ properties:
> - raspberrypi,dsi-7inch
> - startek,kd050hdfia020
> - tdo,tl050hdv35
> + - waveshare,7.0-dsi-touch-a
> - wanchanglong,w552946aaa
One more thing, this looks misplace/unsorted.
Best regards,
Krzysztof
^ permalink raw reply
* Re: [PATCH 03/19] dt-bindings: display/panel: jadard,jd9365da-h3: describe Waveshare panel
From: Krzysztof Kozlowski @ 2026-04-07 10:46 UTC (permalink / raw)
To: Dmitry Baryshkov, Neil Armstrong, Jessica Zhang, David Airlie,
Simona Vetter, Maarten Lankhorst, Maxime Ripard,
Thomas Zimmermann, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Cong Yang, Ondrej Jirman, Javier Martinez Canillas, Jagan Teki,
Liam Girdwood, Mark Brown, Linus Walleij, Bartosz Golaszewski
Cc: dri-devel, devicetree, linux-kernel, linux-gpio
In-Reply-To: <20260401-waveshare-dsi-touch-v1-3-5e9119b5a014@oss.qualcomm.com>
On 01/04/2026 09:26, Dmitry Baryshkov wrote:
> Describe Waveshare DSI panels which use JD9365 as a panel controller.
>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
> ---
> .../devicetree/bindings/display/panel/jadard,jd9365da-h3.yaml | 6 ++++++
> 1 file changed, 6 insertions(+)
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Best regards,
Krzysztof
^ permalink raw reply
* Re: [PATCH 1/2] dt-bindings: net: Add schema for LAN75XX compatible USB Ethernet controllers
From: Krzysztof Kozlowski @ 2026-04-07 10:46 UTC (permalink / raw)
To: Thomas Richard
Cc: Andrew Lunn, David S. Miller, Eric Dumazet, Jakub Kicinski,
Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Aaro Koskinen, Andreas Kemnade, Kevin Hilman, Roger Quadros,
Tony Lindgren, Thomas Petazzoni, netdev, devicetree, linux-kernel,
linux-omap
In-Reply-To: <c2026868-35ff-4b5e-a0e2-bf6b3f6b75ce@bootlin.com>
On 07/04/2026 10:34, Thomas Richard wrote:
>>
>>> + - enum:
>>> + - usb424,7500
>>> + - usb424,7505
>>
>> But you should notice that this is exactly the same as 95xx, so why it
>> cannot go there? Because of the wildcard 95xx naming? That's not a
>> reason.
>
> Yes I noticed. I did not put them in 95xx because it is not the same
> driver. Isn't that a valid reason?
Not really a valid reason. If you split driver into two, do you split
bindings? Or merge drivers? Bindings here describe the hardware, not the
driver layout.
Best regards,
Krzysztof
^ permalink raw reply
* Re: [PATCH 2/2] arm64: dts: qcom: monaco: Add iface clock for ice sdhc
From: Konrad Dybcio @ 2026-04-07 10:45 UTC (permalink / raw)
To: Kuldeep Singh, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel
In-Reply-To: <20260406-ice_emmc_clock_addition-v1-2-e7b237bf7a69@oss.qualcomm.com>
On 4/6/26 6:30 PM, Kuldeep Singh wrote:
> Qualcomm in-line crypto engine (ICE) platform driver specifies and votes
> for its own resources. Before accessing ICE hardware during probe, to
> avoid potential unclocked register access issues (when clk_ignore_unused
> is not passed on the kernel command line), in addition to the 'core'
> clock the 'iface' clock should also be turned on by the driver.
>
> As bindings allow to specify 2 clocks, add iface clock now.
>
> Signed-off-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Konrad
^ permalink raw reply
* Re: [PATCH 1/2] arm64: dts: qcom: kodiak: Add iface clock for ice sdhc
From: Konrad Dybcio @ 2026-04-07 10:45 UTC (permalink / raw)
To: Kuldeep Singh, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel
In-Reply-To: <20260406-ice_emmc_clock_addition-v1-1-e7b237bf7a69@oss.qualcomm.com>
On 4/6/26 6:30 PM, Kuldeep Singh wrote:
> Qualcomm in-line crypto engine (ICE) platform driver specifies and votes
> for its own resources. Before accessing ICE hardware during probe, to
> avoid potential unclocked register access issues (when clk_ignore_unused
> is not passed on the kernel command line), in addition to the 'core'
> clock the 'iface' clock should also be turned on by the driver.
>
> As bindings allow to specify 2 clocks, add iface clock now.
>
> Signed-off-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
> ---
> arch/arm64/boot/dts/qcom/kodiak.dtsi | 3 ++-
> 1 file changed, 2 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/kodiak.dtsi b/arch/arm64/boot/dts/qcom/kodiak.dtsi
> index dda4697a61b7..5e6b659e8719 100644
> --- a/arch/arm64/boot/dts/qcom/kodiak.dtsi
> +++ b/arch/arm64/boot/dts/qcom/kodiak.dtsi
> @@ -1082,7 +1082,8 @@ sdhc_ice: crypto@7c8000 {
> compatible = "qcom,sc7280-inline-crypto-engine",
> "qcom,inline-crypto-engine";
> reg = <0x0 0x007c8000 0x0 0x18000>;
> - clocks = <&gcc GCC_SDCC1_ICE_CORE_CLK>;
> + clocks = <&gcc GCC_SDCC1_ICE_CORE_CLK>, <&gcc GCC_SDCC1_AHB_CLK>;
> + clock-names = "core", "iface";
nit: one a line would be preferred, please fix that up as you seemingly
need a v2 anyway
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Konrad
^ permalink raw reply
* Re: [PATCH 4/4] arm64: dts: qcom: x1e80100-dell-xps13-9345: introduce EC
From: Konrad Dybcio @ 2026-04-07 10:43 UTC (permalink / raw)
To: Aleksandrs Vinarskis
Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Hans de Goede, Ilpo Järvinen,
Bryan O'Donoghue, linux-arm-msm, devicetree, linux-kernel,
platform-driver-x86, laurentiu.tudor1, Abel Vesa, Tobias Heider,
Val Packett
In-Reply-To: <oZ3ETRlKitLSlV93KwI5jlHnDIykdpHxhzThD4pT8FVvY48Y0jrPqDuwI81Zrwy8nwXe7DR0ZUKBTEN9SO8bsPa5xBNWlaNS8u_DG6Kcntc=@vinarskis.com>
On 4/2/26 2:52 PM, Aleksandrs Vinarskis wrote:
>
> On Wednesday, April 1st, 2026 at 11:21, Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> wrote:
>
>> On 4/1/26 9:33 AM, Aleksandrs Vinarskis wrote:
>>> Describe embedded controller, its interrupt and required thermal zones.
>>> Add EC's reset GPIO to reserved range, as triggering it during device
>>> operation leads to unrecoverable and unusable state.
>>>
>>> Signed-off-by: Aleksandrs Vinarskis <alex@vinarskis.com>
>>> ---
>>
>> [...]
>>
>>> + io-channels = <&pmk8550_vadc PM8350_ADC7_GPIO3_100K_PU(1)>,
>>> + <&pmk8550_vadc PM8350_ADC7_GPIO4_100K_PU(1)>,
>>> + <&pmk8550_vadc PM8350_ADC7_AMUX_THM1_100K_PU(1)>,
>>> + <&pmk8550_vadc PM8350_ADC7_AMUX_THM2_100K_PU(1)>,
>>> + <&pmk8550_vadc PM8350_ADC7_AMUX_THM3_100K_PU(1)>,
>>> + <&pmk8550_vadc PM8350_ADC7_AMUX_THM4_100K_PU(1)>,
>>> + <&pmk8550_vadc PM8350_ADC7_AMUX_THM5_100K_PU(1)>;
>>> +
>>> + io-channel-names = "sys_therm0", "sys_therm1", "sys_therm2",
>>> + "sys_therm3", "sys_therm4", "sys_therm5",
>>> + "sys_therm6";
>>
>> nit: one a line please, without a separating \n between x and x-names
>
> Will drop \n. One a line as in:
> io-channel-names = "sys_therm0",
> "sys_therm1",
> "sys_therm2",
> ...
> ?
Yes please
[...]
>>> &tlmm {
>>> gpio-reserved-ranges = <44 4>, /* SPI11 (TPM) */
>>> + <65 1>, /* EC Reset */
>>
>> Is that a "this may not be accessed" or rather "you can, but it has dire
>> consequences"?
>
> The latter. Triggering EC reset appears to leave it in un-initialized state.
> When analyzing i2c dumps I noticed UEFI sends some data to EC prior to
> Windows driver loading, I am assuming its required for EC configuration.
> When resetting EC from userpsace:
> - Keyboard, Trackpad, touch-row power is out. WiFi connection drops. Dell's
> UEFI allows disabling many peripherals, EC can 'veto' their resets and/or
> power supplies. It appears in default reset state it kill some/all outputs
> - Holding power button does not reboot laptop, it looks as if it asserts and
> holds EC in reset until released. During this time fans spin to max speed.
> - Device can be recovered only by disassembly and battery removal.
>
>>
>> Would the EC driver/binding benefit from having a reference to that pin?
>
> It will not be used by the driver, and it would greatly inconvenience user
> if triggered manually. I would make the reset pin as inaccessible as
> possible, but if you say its cleaner to reference it to EC driver and just
> not use it, I could do that as well.
I would assume the EC is powered from some always-on rail, or that it can
at least somehow sustain entry into all the various low power modes and we
won't have to re-initialize it from Linux, but that's only a guess
That said, like you suggest, exposing that pin currently causes more harm
than good and we can always circle back and revert this in the future, should
that become desired, perhaps with the only caveat being that users of old DTs
(i.e. without that description) would not get the ability to reset the EC on
demand
Konrad
^ permalink raw reply
* [PATCH V11 12/12] arm64: dts: imx95: Add Root Port node and PERST property
From: Sherry Sun @ 2026-04-07 10:41 UTC (permalink / raw)
To: robh, krzk+dt, conor+dt, Frank.Li, s.hauer, kernel, festevam,
lpieralisi, kwilczynski, mani, bhelgaas, hongxing.zhu, l.stach
Cc: imx, linux-pci, linux-arm-kernel, devicetree, linux-kernel
In-Reply-To: <20260407104154.2842132-1-sherry.sun@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
.../boot/dts/freescale/imx95-15x15-evk.dts | 5 +++++
.../boot/dts/freescale/imx95-19x19-evk.dts | 10 +++++++++
arch/arm64/boot/dts/freescale/imx95.dtsi | 22 +++++++++++++++++++
3 files changed, 37 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx95-15x15-evk.dts b/arch/arm64/boot/dts/freescale/imx95-15x15-evk.dts
index e4649d7f9122..7d820a0f80b2 100644
--- a/arch/arm64/boot/dts/freescale/imx95-15x15-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx95-15x15-evk.dts
@@ -553,6 +553,7 @@ &netcmix_blk_ctrl {
&pcie0 {
pinctrl-0 = <&pinctrl_pcie0>;
pinctrl-names = "default";
+ /* This property is deprecated, use reset-gpios from the Root Port node. */
reset-gpio = <&gpio5 13 GPIO_ACTIVE_LOW>;
vpcie-supply = <®_m2_pwr>;
vpcie3v3aux-supply = <®_m2_pwr>;
@@ -567,6 +568,10 @@ &pcie0_ep {
status = "disabled";
};
+&pcie0_port0 {
+ reset-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+};
+
&sai1 {
assigned-clocks = <&scmi_clk IMX95_CLK_AUDIOPLL1_VCO>,
<&scmi_clk IMX95_CLK_AUDIOPLL2_VCO>,
diff --git a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
index 041fd838fabb..6f193cf04119 100644
--- a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
@@ -540,6 +540,7 @@ &netc_timer {
&pcie0 {
pinctrl-0 = <&pinctrl_pcie0>;
pinctrl-names = "default";
+ /* This property is deprecated, use reset-gpios from the Root Port node. */
reset-gpio = <&i2c7_pcal6524 5 GPIO_ACTIVE_LOW>;
vpcie-supply = <®_pcie0>;
vpcie3v3aux-supply = <®_pcie0>;
@@ -554,9 +555,14 @@ &pcie0_ep {
status = "disabled";
};
+&pcie0_port0 {
+ reset-gpios = <&i2c7_pcal6524 5 GPIO_ACTIVE_LOW>;
+};
+
&pcie1 {
pinctrl-0 = <&pinctrl_pcie1>;
pinctrl-names = "default";
+ /* This property is deprecated, use reset-gpios from the Root Port node. */
reset-gpio = <&i2c7_pcal6524 16 GPIO_ACTIVE_LOW>;
vpcie-supply = <®_slot_pwr>;
vpcie3v3aux-supply = <®_slot_pwr>;
@@ -570,6 +576,10 @@ &pcie1_ep {
status = "disabled";
};
+&pcie1_port0 {
+ reset-gpios = <&i2c7_pcal6524 16 GPIO_ACTIVE_LOW>;
+};
+
&sai1 {
#sound-dai-cells = <0>;
pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/freescale/imx95.dtsi b/arch/arm64/boot/dts/freescale/imx95.dtsi
index 71394871d8dd..0cc6644f98bb 100644
--- a/arch/arm64/boot/dts/freescale/imx95.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx95.dtsi
@@ -1890,6 +1890,17 @@ pcie0: pcie@4c300000 {
iommu-map-mask = <0x1ff>;
fsl,max-link-speed = <3>;
status = "disabled";
+
+ pcie0_port0: pcie@0 {
+ compatible = "pciclass,0604";
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ bus-range = <0x01 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ };
};
pcie0_ep: pcie-ep@4c300000 {
@@ -1967,6 +1978,17 @@ pcie1: pcie@4c380000 {
iommu-map-mask = <0x1ff>;
fsl,max-link-speed = <3>;
status = "disabled";
+
+ pcie1_port0: pcie@0 {
+ compatible = "pciclass,0604";
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ bus-range = <0x01 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ };
};
pcie1_ep: pcie-ep@4c380000 {
--
2.37.1
^ permalink raw reply related
* [PATCH V11 11/12] arm64: dts: imx8dxl/qm/qxp: Add Root Port node and PERST property
From: Sherry Sun @ 2026-04-07 10:41 UTC (permalink / raw)
To: robh, krzk+dt, conor+dt, Frank.Li, s.hauer, kernel, festevam,
lpieralisi, kwilczynski, mani, bhelgaas, hongxing.zhu, l.stach
Cc: imx, linux-pci, linux-arm-kernel, devicetree, linux-kernel
In-Reply-To: <20260407104154.2842132-1-sherry.sun@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
.../boot/dts/freescale/imx8-ss-hsio.dtsi | 11 ++++++++++
arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 5 +++++
arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 10 +++++++++
.../boot/dts/freescale/imx8qm-ss-hsio.dtsi | 22 +++++++++++++++++++
arch/arm64/boot/dts/freescale/imx8qxp-mek.dts | 5 +++++
5 files changed, 53 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-hsio.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-hsio.dtsi
index 469de8b536b5..009990b2e559 100644
--- a/arch/arm64/boot/dts/freescale/imx8-ss-hsio.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8-ss-hsio.dtsi
@@ -78,6 +78,17 @@ pcieb: pcie@5f010000 {
power-domains = <&pd IMX_SC_R_PCIE_B>;
fsl,max-link-speed = <3>;
status = "disabled";
+
+ pcieb_port0: pcie@0 {
+ compatible = "pciclass,0604";
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ bus-range = <0x01 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ };
};
pcieb_ep: pcie-ep@5f010000 {
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
index bc62ae5ca812..39108a915f96 100644
--- a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
@@ -675,6 +675,7 @@ &pcie0 {
phy-names = "pcie-phy";
pinctrl-0 = <&pinctrl_pcieb>;
pinctrl-names = "default";
+ /* This property is deprecated, use reset-gpios from the Root Port node. */
reset-gpio = <&lsio_gpio4 0 GPIO_ACTIVE_LOW>;
vpcie-supply = <®_pcieb>;
vpcie3v3aux-supply = <®_pcieb>;
@@ -691,6 +692,10 @@ &pcie0_ep {
status = "disabled";
};
+&pcieb_port0 {
+ reset-gpios = <&lsio_gpio4 0 GPIO_ACTIVE_LOW>;
+};
+
&sai0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sai0>;
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
index 011a89d85961..f706c86137c0 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
@@ -810,6 +810,7 @@ &pciea {
phy-names = "pcie-phy";
pinctrl-0 = <&pinctrl_pciea>;
pinctrl-names = "default";
+ /* This property is deprecated, use reset-gpios from the Root Port node. */
reset-gpio = <&lsio_gpio4 29 GPIO_ACTIVE_LOW>;
vpcie-supply = <®_pciea>;
vpcie3v3aux-supply = <®_pciea>;
@@ -817,15 +818,24 @@ &pciea {
status = "okay";
};
+&pciea_port0 {
+ reset-gpios = <&lsio_gpio4 29 GPIO_ACTIVE_LOW>;
+};
+
&pcieb {
phys = <&hsio_phy 1 PHY_TYPE_PCIE 1>;
phy-names = "pcie-phy";
pinctrl-0 = <&pinctrl_pcieb>;
pinctrl-names = "default";
+ /* This property is deprecated, use reset-gpios from the Root Port node. */
reset-gpio = <&lsio_gpio5 0 GPIO_ACTIVE_LOW>;
status = "disabled";
};
+&pcieb_port0 {
+ reset-gpios = <&lsio_gpio5 0 GPIO_ACTIVE_LOW>;
+};
+
&qm_pwm_lvds0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm_lvds0>;
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-ss-hsio.dtsi b/arch/arm64/boot/dts/freescale/imx8qm-ss-hsio.dtsi
index f2c94cdb682b..2e4fbfe0ca16 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-ss-hsio.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8qm-ss-hsio.dtsi
@@ -41,6 +41,17 @@ pcie0: pciea: pcie@5f000000 {
power-domains = <&pd IMX_SC_R_PCIE_A>;
fsl,max-link-speed = <3>;
status = "disabled";
+
+ pciea_port0: pcie@0 {
+ compatible = "pciclass,0604";
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ bus-range = <0x01 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ };
};
pcie0_ep: pciea_ep: pcie-ep@5f000000 {
@@ -91,6 +102,17 @@ pcie1: pcieb: pcie@5f010000 {
power-domains = <&pd IMX_SC_R_PCIE_B>;
fsl,max-link-speed = <3>;
status = "disabled";
+
+ pcieb_port0: pcie@0 {
+ compatible = "pciclass,0604";
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ bus-range = <0x01 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ };
};
sata: sata@5f020000 {
diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
index 623169f7ddb5..489e174df4c4 100644
--- a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
@@ -730,6 +730,7 @@ &pcie0 {
phy-names = "pcie-phy";
pinctrl-0 = <&pinctrl_pcieb>;
pinctrl-names = "default";
+ /* This property is deprecated, use reset-gpios from the Root Port node. */
reset-gpios = <&lsio_gpio4 0 GPIO_ACTIVE_LOW>;
vpcie-supply = <®_pcieb>;
vpcie3v3aux-supply = <®_pcieb>;
@@ -746,6 +747,10 @@ &pcie0_ep {
status = "disabled";
};
+&pcieb_port0 {
+ reset-gpios = <&lsio_gpio4 0 GPIO_ACTIVE_LOW>;
+};
+
&scu_key {
status = "okay";
};
--
2.37.1
^ permalink raw reply related
* [PATCH V11 10/12] arm64: dts: imx8mq: Add Root Port node and PERST property
From: Sherry Sun @ 2026-04-07 10:41 UTC (permalink / raw)
To: robh, krzk+dt, conor+dt, Frank.Li, s.hauer, kernel, festevam,
lpieralisi, kwilczynski, mani, bhelgaas, hongxing.zhu, l.stach
Cc: imx, linux-pci, linux-arm-kernel, devicetree, linux-kernel
In-Reply-To: <20260407104154.2842132-1-sherry.sun@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8mq-evk.dts | 10 +++++++++
arch/arm64/boot/dts/freescale/imx8mq.dtsi | 22 ++++++++++++++++++++
2 files changed, 32 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
index d48f901487d4..e7d87ea81b69 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
@@ -369,6 +369,7 @@ mipi_dsi_out: endpoint {
&pcie0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pcie0>;
+ /* This property is deprecated, use reset-gpios from the Root Port node. */
reset-gpio = <&gpio5 28 GPIO_ACTIVE_LOW>;
clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>,
<&pcie0_refclk>,
@@ -389,9 +390,14 @@ &pcie0_ep {
status = "disabled";
};
+&pcie0_port0 {
+ reset-gpios = <&gpio5 28 GPIO_ACTIVE_LOW>;
+};
+
&pcie1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pcie1>;
+ /* This property is deprecated, use reset-gpios from the Root Port node. */
reset-gpio = <&gpio5 12 GPIO_ACTIVE_LOW>;
clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>,
<&pcie0_refclk>,
@@ -414,6 +420,10 @@ &pcie1_ep {
status = "disabled";
};
+&pcie1_port0 {
+ reset-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
+};
+
&pgc_gpu {
power-supply = <&sw1a_reg>;
};
diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
index 6a25e219832c..e60872aeeb49 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
@@ -1768,6 +1768,17 @@ pcie0: pcie@33800000 {
assigned-clock-rates = <250000000>, <100000000>,
<10000000>;
status = "disabled";
+
+ pcie0_port0: pcie@0 {
+ compatible = "pciclass,0604";
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ bus-range = <0x01 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ };
};
pcie0_ep: pcie-ep@33800000 {
@@ -1846,6 +1857,17 @@ pcie1: pcie@33c00000 {
assigned-clock-rates = <250000000>, <100000000>,
<10000000>;
status = "disabled";
+
+ pcie1_port0: pcie@0 {
+ compatible = "pciclass,0604";
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ bus-range = <0x01 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ };
};
pcie1_ep: pcie-ep@33c00000 {
--
2.37.1
^ permalink raw reply related
* [PATCH V11 09/12] arm64: dts: imx8mp: Add Root Port node and PERST property
From: Sherry Sun @ 2026-04-07 10:41 UTC (permalink / raw)
To: robh, krzk+dt, conor+dt, Frank.Li, s.hauer, kernel, festevam,
lpieralisi, kwilczynski, mani, bhelgaas, hongxing.zhu, l.stach
Cc: imx, linux-pci, linux-arm-kernel, devicetree, linux-kernel
In-Reply-To: <20260407104154.2842132-1-sherry.sun@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8mp-evk.dts | 5 +++++
arch/arm64/boot/dts/freescale/imx8mp.dtsi | 11 +++++++++++
2 files changed, 16 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
index 2feb5b18645c..a7f3acdc36d1 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
@@ -770,6 +770,7 @@ &pcie_phy {
&pcie0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pcie0>;
+ /* This property is deprecated, use reset-gpios from the Root Port node. */
reset-gpio = <&gpio2 7 GPIO_ACTIVE_LOW>;
vpcie-supply = <®_pcie0>;
vpcie3v3aux-supply = <®_pcie0>;
@@ -783,6 +784,10 @@ &pcie0_ep {
status = "disabled";
};
+&pcie0_port0 {
+ reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+};
+
&pwm1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
index 90d7bb8f5619..5ce2825182fd 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
@@ -2265,6 +2265,17 @@ pcie0: pcie: pcie@33800000 {
phys = <&pcie_phy>;
phy-names = "pcie-phy";
status = "disabled";
+
+ pcie0_port0: pcie@0 {
+ compatible = "pciclass,0604";
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ bus-range = <0x01 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ };
};
pcie0_ep: pcie_ep: pcie-ep@33800000 {
--
2.37.1
^ permalink raw reply related
* [PATCH V11 08/12] arm64: dts: imx8mm: Add Root Port node and PERST property
From: Sherry Sun @ 2026-04-07 10:41 UTC (permalink / raw)
To: robh, krzk+dt, conor+dt, Frank.Li, s.hauer, kernel, festevam,
lpieralisi, kwilczynski, mani, bhelgaas, hongxing.zhu, l.stach
Cc: imx, linux-pci, linux-arm-kernel, devicetree, linux-kernel
In-Reply-To: <20260407104154.2842132-1-sherry.sun@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi | 5 +++++
arch/arm64/boot/dts/freescale/imx8mm.dtsi | 11 +++++++++++
2 files changed, 16 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
index 8be44eaf4e1e..e03aba825c18 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
@@ -533,6 +533,7 @@ &pcie_phy {
&pcie0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pcie0>;
+ /* This property is deprecated, use reset-gpios from the Root Port node. */
reset-gpio = <&gpio4 21 GPIO_ACTIVE_LOW>;
clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&pcie0_refclk>,
<&clk IMX8MM_CLK_PCIE1_AUX>;
@@ -559,6 +560,10 @@ &pcie0_ep {
status = "disabled";
};
+&pcie0_port0 {
+ reset-gpios = <&gpio4 21 GPIO_ACTIVE_LOW>;
+};
+
&sai2 {
#sound-dai-cells = <0>;
pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
index 4cc5ad01d0e2..5cf2998d396d 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -1370,6 +1370,17 @@ pcie0: pcie@33800000 {
phys = <&pcie_phy>;
phy-names = "pcie-phy";
status = "disabled";
+
+ pcie0_port0: pcie@0 {
+ compatible = "pciclass,0604";
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ bus-range = <0x01 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ };
};
pcie0_ep: pcie-ep@33800000 {
--
2.37.1
^ permalink raw reply related
* [PATCH V11 07/12] arm: dts: imx7d: Add Root Port node and PERST property
From: Sherry Sun @ 2026-04-07 10:41 UTC (permalink / raw)
To: robh, krzk+dt, conor+dt, Frank.Li, s.hauer, kernel, festevam,
lpieralisi, kwilczynski, mani, bhelgaas, hongxing.zhu, l.stach
Cc: imx, linux-pci, linux-arm-kernel, devicetree, linux-kernel
In-Reply-To: <20260407104154.2842132-1-sherry.sun@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts | 5 +++++
arch/arm/boot/dts/nxp/imx/imx7d.dtsi | 11 +++++++++++
2 files changed, 16 insertions(+)
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts b/arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts
index a370e868cafe..0046b276b8b9 100644
--- a/arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts
@@ -456,10 +456,15 @@ display_out: endpoint {
};
&pcie {
+ /* This property is deprecated, use reset-gpios from the Root Port node. */
reset-gpio = <&extended_io 1 GPIO_ACTIVE_LOW>;
status = "okay";
};
+&pcie_port0 {
+ reset-gpios = <&extended_io 1 GPIO_ACTIVE_LOW>;
+};
+
®_1p0d {
vin-supply = <&sw2_reg>;
};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d.dtsi b/arch/arm/boot/dts/nxp/imx/imx7d.dtsi
index d961c61a93af..3c5c1f2c1460 100644
--- a/arch/arm/boot/dts/nxp/imx/imx7d.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7d.dtsi
@@ -155,6 +155,17 @@ pcie: pcie@33800000 {
reset-names = "pciephy", "apps", "turnoff";
fsl,imx7d-pcie-phy = <&pcie_phy>;
status = "disabled";
+
+ pcie_port0: pcie@0 {
+ compatible = "pciclass,0604";
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ bus-range = <0x01 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ };
};
};
};
--
2.37.1
^ permalink raw reply related
* [PATCH V11 06/12] arm: dts: imx6sx: Add Root Port node and PERST property
From: Sherry Sun @ 2026-04-07 10:41 UTC (permalink / raw)
To: robh, krzk+dt, conor+dt, Frank.Li, s.hauer, kernel, festevam,
lpieralisi, kwilczynski, mani, bhelgaas, hongxing.zhu, l.stach
Cc: imx, linux-pci, linux-arm-kernel, devicetree, linux-kernel
In-Reply-To: <20260407104154.2842132-1-sherry.sun@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi | 5 +++++
arch/arm/boot/dts/nxp/imx/imx6sx.dtsi | 11 +++++++++++
2 files changed, 16 insertions(+)
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi
index 3e238d8118fa..338de4d144b2 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi
@@ -282,11 +282,16 @@ codec: wm8962@1a {
&pcie {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pcie>;
+ /* This property is deprecated, use reset-gpios from the Root Port node. */
reset-gpio = <&gpio2 0 GPIO_ACTIVE_LOW>;
vpcie-supply = <®_pcie_gpio>;
status = "okay";
};
+&pcie_port0 {
+ reset-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+};
+
&lcdif1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lcd>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
index aefae5a3a6be..5484c398aa37 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
@@ -1470,6 +1470,17 @@ pcie: pcie@8ffc000 {
power-domains = <&pd_disp>, <&pd_pci>;
power-domain-names = "pcie", "pcie_phy";
status = "disabled";
+
+ pcie_port0: pcie@0 {
+ compatible = "pciclass,0604";
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ bus-range = <0x01 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ };
};
};
};
--
2.37.1
^ permalink raw reply related
* [PATCH V11 05/12] arm: dts: imx6qdl: Add Root Port node and PERST property
From: Sherry Sun @ 2026-04-07 10:41 UTC (permalink / raw)
To: robh, krzk+dt, conor+dt, Frank.Li, s.hauer, kernel, festevam,
lpieralisi, kwilczynski, mani, bhelgaas, hongxing.zhu, l.stach
Cc: imx, linux-pci, linux-arm-kernel, devicetree, linux-kernel
In-Reply-To: <20260407104154.2842132-1-sherry.sun@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi | 5 +++++
arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi | 11 +++++++++++
arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts | 5 +++++
3 files changed, 21 insertions(+)
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi
index ba29720e3f72..fe9046c03ddd 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi
@@ -754,11 +754,16 @@ lvds0_out: endpoint {
&pcie {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pcie>;
+ /* This property is deprecated, use reset-gpios from the Root Port node. */
reset-gpio = <&gpio7 12 GPIO_ACTIVE_LOW>;
vpcie-supply = <®_pcie>;
status = "okay";
};
+&pcie_port0 {
+ reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
+};
+
&pwm1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
index 4dc2c410cf61..9438862b9927 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
@@ -302,6 +302,17 @@ pcie: pcie@1ffc000 {
<&clks IMX6QDL_CLK_PCIE_REF_125M>;
clock-names = "pcie", "pcie_bus", "pcie_phy";
status = "disabled";
+
+ pcie_port0: pcie@0 {
+ compatible = "pciclass,0604";
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ bus-range = <0x01 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ };
};
aips1: bus@2000000 { /* AIPS1 */
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts
index c5b220aeaefd..6b12cab7175f 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts
@@ -45,10 +45,15 @@ MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1
};
&pcie {
+ /* This property is deprecated, use reset-gpios from the Root Port node. */
reset-gpio = <&max7310_c 5 GPIO_ACTIVE_LOW>;
status = "okay";
};
+&pcie_port0 {
+ reset-gpios = <&max7310_c 5 GPIO_ACTIVE_LOW>;
+};
+
&sata {
status = "okay";
};
--
2.37.1
^ permalink raw reply related
* [PATCH V11 04/12] PCI: imx6: Add support for parsing the reset property in new Root Port binding
From: Sherry Sun @ 2026-04-07 10:41 UTC (permalink / raw)
To: robh, krzk+dt, conor+dt, Frank.Li, s.hauer, kernel, festevam,
lpieralisi, kwilczynski, mani, bhelgaas, hongxing.zhu, l.stach
Cc: imx, linux-pci, linux-arm-kernel, devicetree, linux-kernel
In-Reply-To: <20260407104154.2842132-1-sherry.sun@nxp.com>
The current DT binding for pci-imx6 specifies the 'reset-gpios' property
in the host bridge node. However, the PERST# signal logically belongs to
individual Root Ports rather than the host bridge itself. This becomes
important when supporting PCIe KeyE connector and PCI power control
framework for pci-imx6 driver, which requires properties to be specified
in Root Port nodes.
Add support for parsing 'reset-gpios' from Root Port child nodes using
the common helper pci_host_common_parse_ports(), and update the reset
GPIO handling to use the parsed port list from bridge->ports. To
maintain DT backwards compatibility, fallback to the legacy method of
parsing the host bridge node if the reset property is not present in the
Root Port node.
Since now the reset GPIO is obtained with GPIOD_ASIS flag, it may be in
input mode, using gpiod_direction_output() instead of
gpiod_set_value_cansleep() to ensure the reset GPIO is properly
configured as output before setting its value.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
drivers/pci/controller/dwc/pci-imx6.c | 75 +++++++++++++++++++++------
1 file changed, 60 insertions(+), 15 deletions(-)
diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index d99da7e42590..dd8f9c0fcec4 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -34,6 +34,7 @@
#include <linux/pm_runtime.h>
#include "../../pci.h"
+#include "../pci-host-common.h"
#include "pcie-designware.h"
#define IMX8MQ_GPR_PCIE_REF_USE_PAD BIT(9)
@@ -152,7 +153,6 @@ struct imx_lut_data {
struct imx_pcie {
struct dw_pcie *pci;
- struct gpio_desc *reset_gpiod;
struct clk_bulk_data *clks;
int num_clks;
bool supports_clkreq;
@@ -1224,6 +1224,32 @@ static void imx_pcie_disable_device(struct pci_host_bridge *bridge,
imx_pcie_remove_lut(imx_pcie, pci_dev_id(pdev));
}
+static int imx_pcie_parse_legacy_binding(struct imx_pcie *pcie)
+{
+ struct device *dev = pcie->pci->dev;
+ struct pci_host_bridge *bridge = pcie->pci->pp.bridge;
+ struct pci_host_port *port;
+ struct gpio_desc *reset;
+
+ reset = devm_gpiod_get_optional(dev, "reset", GPIOD_ASIS);
+ if (IS_ERR(reset))
+ return PTR_ERR(reset);
+
+ if (!reset)
+ return 0;
+
+ port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
+ if (!port)
+ return -ENOMEM;
+
+ port->reset = reset;
+ INIT_LIST_HEAD(&port->list);
+ list_add_tail(&port->list, &bridge->ports);
+
+ return devm_add_action_or_reset(dev, pci_host_common_delete_ports,
+ &bridge->ports);
+}
+
static void imx_pcie_vpcie_aux_disable(void *data)
{
struct regulator *vpcie_aux = data;
@@ -1233,13 +1259,22 @@ static void imx_pcie_vpcie_aux_disable(void *data)
static void imx_pcie_assert_perst(struct imx_pcie *imx_pcie, bool assert)
{
- if (assert) {
- gpiod_set_value_cansleep(imx_pcie->reset_gpiod, 1);
- } else {
- if (imx_pcie->reset_gpiod) {
- msleep(PCIE_T_PVPERL_MS);
- gpiod_set_value_cansleep(imx_pcie->reset_gpiod, 0);
- msleep(PCIE_RESET_CONFIG_WAIT_MS);
+ struct dw_pcie *pci = imx_pcie->pci;
+ struct pci_host_bridge *bridge = pci->pp.bridge;
+ struct pci_host_port *port;
+
+ if (!bridge)
+ return;
+
+ list_for_each_entry(port, &bridge->ports, list) {
+ if (assert) {
+ gpiod_direction_output(port->reset, 1);
+ } else {
+ if (port->reset) {
+ msleep(PCIE_T_PVPERL_MS);
+ gpiod_direction_output(port->reset, 0);
+ msleep(PCIE_RESET_CONFIG_WAIT_MS);
+ }
}
}
}
@@ -1249,8 +1284,25 @@ static int imx_pcie_host_init(struct dw_pcie_rp *pp)
struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
struct device *dev = pci->dev;
struct imx_pcie *imx_pcie = to_imx_pcie(pci);
+ struct pci_host_bridge *bridge = pp->bridge;
int ret;
+ if (bridge && list_empty(&bridge->ports)) {
+ /* Parse Root Port nodes if present */
+ ret = pci_host_common_parse_ports(dev, bridge);
+ if (ret) {
+ if (ret != -ENOENT) {
+ dev_err(dev, "Failed to parse Root Port nodes: %d\n", ret);
+ return ret;
+ }
+
+ /* Fallback to legacy binding for DT backwards compatibility */
+ ret = imx_pcie_parse_legacy_binding(imx_pcie);
+ if (ret)
+ return ret;
+ }
+ }
+
imx_pcie_assert_perst(imx_pcie, true);
/* Keep 3.3Vaux supply enabled for the entire PCIe controller lifecycle */
@@ -1704,13 +1756,6 @@ static int imx_pcie_probe(struct platform_device *pdev)
return PTR_ERR(imx_pcie->phy_base);
}
- /* Fetch GPIOs */
- imx_pcie->reset_gpiod = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
- if (IS_ERR(imx_pcie->reset_gpiod))
- return dev_err_probe(dev, PTR_ERR(imx_pcie->reset_gpiod),
- "unable to get reset gpio\n");
- gpiod_set_consumer_name(imx_pcie->reset_gpiod, "PCIe reset");
-
/* Fetch clocks */
imx_pcie->num_clks = devm_clk_bulk_get_all(dev, &imx_pcie->clks);
if (imx_pcie->num_clks < 0)
--
2.37.1
^ permalink raw reply related
* [PATCH V11 03/12] PCI: imx6: Assert PERST# before enabling regulators
From: Sherry Sun @ 2026-04-07 10:41 UTC (permalink / raw)
To: robh, krzk+dt, conor+dt, Frank.Li, s.hauer, kernel, festevam,
lpieralisi, kwilczynski, mani, bhelgaas, hongxing.zhu, l.stach
Cc: imx, linux-pci, linux-arm-kernel, devicetree, linux-kernel
In-Reply-To: <20260407104154.2842132-1-sherry.sun@nxp.com>
The PCIe endpoint may start responding or driving signals as soon as
its supply is enabled, even before the reference clock is stable.
Asserting PERST# before enabling the regulator ensures that the
endpoint remains in reset throughout the entire power-up sequence,
until both power and refclk are known to be stable and link
initialization can safely begin.
Currently, the driver enables the vpcie3v3aux regulator in
imx_pcie_probe() before PERST# is asserted in imx_pcie_host_init(),
which may cause PCIe endpoint undefined behavior during early
power-up. However, there is no issue so far because PERST# is
requested as GPIOD_OUT_HIGH in imx_pcie_probe(), which guarantees
that PERST# is asserted before enabling the vpcie3v3aux regulator.
This is prepare for the upcoming changes that will parse the reset
property using the new Root Port binding, which will use GPIOD_ASIS
when requesting the reset GPIO. With GPIOD_ASIS, the GPIO state is not
guaranteed, so explicit sequencing is required.
Fix the power sequencing by:
1. Moving vpcie3v3aux regulator enable from probe to
imx_pcie_host_init(), where it can be properly sequenced with PERST#.
2. Moving imx_pcie_assert_perst() before regulator and clock enable to
ensure correct ordering.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
drivers/pci/controller/dwc/pci-imx6.c | 49 +++++++++++++++++++++------
1 file changed, 39 insertions(+), 10 deletions(-)
diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index 915061ea75b9..d99da7e42590 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -168,6 +168,8 @@ struct imx_pcie {
u32 tx_swing_full;
u32 tx_swing_low;
struct regulator *vpcie;
+ struct regulator *vpcie_aux;
+ bool vpcie_aux_enabled;
struct regulator *vph;
void __iomem *phy_base;
@@ -1222,6 +1224,13 @@ static void imx_pcie_disable_device(struct pci_host_bridge *bridge,
imx_pcie_remove_lut(imx_pcie, pci_dev_id(pdev));
}
+static void imx_pcie_vpcie_aux_disable(void *data)
+{
+ struct regulator *vpcie_aux = data;
+
+ regulator_disable(vpcie_aux);
+}
+
static void imx_pcie_assert_perst(struct imx_pcie *imx_pcie, bool assert)
{
if (assert) {
@@ -1242,6 +1251,24 @@ static int imx_pcie_host_init(struct dw_pcie_rp *pp)
struct imx_pcie *imx_pcie = to_imx_pcie(pci);
int ret;
+ imx_pcie_assert_perst(imx_pcie, true);
+
+ /* Keep 3.3Vaux supply enabled for the entire PCIe controller lifecycle */
+ if (imx_pcie->vpcie_aux && !imx_pcie->vpcie_aux_enabled) {
+ ret = regulator_enable(imx_pcie->vpcie_aux);
+ if (ret) {
+ dev_err(dev, "failed to enable vpcie_aux regulator: %d\n",
+ ret);
+ return ret;
+ }
+ imx_pcie->vpcie_aux_enabled = true;
+
+ ret = devm_add_action_or_reset(dev, imx_pcie_vpcie_aux_disable,
+ imx_pcie->vpcie_aux);
+ if (ret)
+ return ret;
+ }
+
if (imx_pcie->vpcie) {
ret = regulator_enable(imx_pcie->vpcie);
if (ret) {
@@ -1251,25 +1278,24 @@ static int imx_pcie_host_init(struct dw_pcie_rp *pp)
}
}
+ ret = imx_pcie_clk_enable(imx_pcie);
+ if (ret) {
+ dev_err(dev, "unable to enable pcie clocks: %d\n", ret);
+ goto err_reg_disable;
+ }
+
if (pp->bridge && imx_check_flag(imx_pcie, IMX_PCIE_FLAG_HAS_LUT)) {
pp->bridge->enable_device = imx_pcie_enable_device;
pp->bridge->disable_device = imx_pcie_disable_device;
}
imx_pcie_assert_core_reset(imx_pcie);
- imx_pcie_assert_perst(imx_pcie, true);
if (imx_pcie->drvdata->init_phy)
imx_pcie->drvdata->init_phy(imx_pcie);
imx_pcie_configure_type(imx_pcie);
- ret = imx_pcie_clk_enable(imx_pcie);
- if (ret) {
- dev_err(dev, "unable to enable pcie clocks: %d\n", ret);
- goto err_reg_disable;
- }
-
if (imx_pcie->phy) {
ret = phy_init(imx_pcie->phy);
if (ret) {
@@ -1782,9 +1808,12 @@ static int imx_pcie_probe(struct platform_device *pdev)
of_property_read_u32(node, "fsl,max-link-speed", &pci->max_link_speed);
imx_pcie->supports_clkreq = of_property_read_bool(node, "supports-clkreq");
- ret = devm_regulator_get_enable_optional(&pdev->dev, "vpcie3v3aux");
- if (ret < 0 && ret != -ENODEV)
- return dev_err_probe(dev, ret, "failed to enable Vaux supply\n");
+ imx_pcie->vpcie_aux = devm_regulator_get_optional(&pdev->dev, "vpcie3v3aux");
+ if (IS_ERR(imx_pcie->vpcie_aux)) {
+ if (PTR_ERR(imx_pcie->vpcie_aux) != -ENODEV)
+ return PTR_ERR(imx_pcie->vpcie_aux);
+ imx_pcie->vpcie_aux = NULL;
+ }
imx_pcie->vpcie = devm_regulator_get_optional(&pdev->dev, "vpcie");
if (IS_ERR(imx_pcie->vpcie)) {
--
2.37.1
^ permalink raw reply related
* [PATCH V11 02/12] PCI: host-generic: Add common helpers for parsing Root Port properties
From: Sherry Sun @ 2026-04-07 10:41 UTC (permalink / raw)
To: robh, krzk+dt, conor+dt, Frank.Li, s.hauer, kernel, festevam,
lpieralisi, kwilczynski, mani, bhelgaas, hongxing.zhu, l.stach
Cc: imx, linux-pci, linux-arm-kernel, devicetree, linux-kernel
In-Reply-To: <20260407104154.2842132-1-sherry.sun@nxp.com>
Introduce generic helper functions to parse Root Port device tree nodes
and extract common properties like reset GPIOs. This allows multiple
PCI host controller drivers to share the same parsing logic.
Define struct pci_host_port to hold common Root Port properties
(currently only reset GPIO descriptor) and add
pci_host_common_parse_ports() to parse Root Port nodes from device tree.
Also add the 'ports' list to struct pci_host_bridge for better maintain
parsed Root Port information.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
drivers/pci/controller/pci-host-common.c | 77 ++++++++++++++++++++++++
drivers/pci/controller/pci-host-common.h | 16 +++++
drivers/pci/probe.c | 1 +
include/linux/pci.h | 1 +
4 files changed, 95 insertions(+)
diff --git a/drivers/pci/controller/pci-host-common.c b/drivers/pci/controller/pci-host-common.c
index d6258c1cffe5..0fb6991dde7b 100644
--- a/drivers/pci/controller/pci-host-common.c
+++ b/drivers/pci/controller/pci-host-common.c
@@ -9,6 +9,7 @@
#include <linux/kernel.h>
#include <linux/module.h>
+#include <linux/gpio/consumer.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_pci.h>
@@ -17,6 +18,82 @@
#include "pci-host-common.h"
+/**
+ * pci_host_common_delete_ports - Cleanup function for port list
+ * @data: Pointer to the port list head
+ */
+void pci_host_common_delete_ports(void *data)
+{
+ struct list_head *ports = data;
+ struct pci_host_port *port, *tmp;
+
+ list_for_each_entry_safe(port, tmp, ports, list)
+ list_del(&port->list);
+}
+EXPORT_SYMBOL_GPL(pci_host_common_delete_ports);
+
+/**
+ * pci_host_common_parse_port - Parse a single Root Port node
+ * @dev: Device pointer
+ * @bridge: PCI host bridge
+ * @node: Device tree node of the Root Port
+ *
+ * Returns: 0 on success, negative error code on failure
+ */
+static int pci_host_common_parse_port(struct device *dev,
+ struct pci_host_bridge *bridge,
+ struct device_node *node)
+{
+ struct pci_host_port *port;
+ struct gpio_desc *reset;
+
+ reset = devm_fwnode_gpiod_get(dev, of_fwnode_handle(node),
+ "reset", GPIOD_ASIS, "PERST#");
+ if (IS_ERR(reset))
+ return PTR_ERR(reset);
+
+ port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
+ if (!port)
+ return -ENOMEM;
+
+ port->reset = reset;
+ INIT_LIST_HEAD(&port->list);
+ list_add_tail(&port->list, &bridge->ports);
+
+ return 0;
+}
+
+/**
+ * pci_host_common_parse_ports - Parse Root Port nodes from device tree
+ * @dev: Device pointer
+ * @bridge: PCI host bridge
+ *
+ * This function iterates through child nodes of the host bridge and parses
+ * Root Port properties (currently only reset GPIO).
+ *
+ * Returns: 0 on success, -ENOENT if no ports found, other negative error codes
+ * on failure
+ */
+int pci_host_common_parse_ports(struct device *dev, struct pci_host_bridge *bridge)
+{
+ int ret = -ENOENT;
+
+ for_each_available_child_of_node_scoped(dev->of_node, of_port) {
+ if (!of_node_is_type(of_port, "pci"))
+ continue;
+ ret = pci_host_common_parse_port(dev, bridge, of_port);
+ if (ret)
+ return ret;
+ }
+
+ if (ret)
+ return ret;
+
+ return devm_add_action_or_reset(dev, pci_host_common_delete_ports,
+ &bridge->ports);
+}
+EXPORT_SYMBOL_GPL(pci_host_common_parse_ports);
+
static void gen_pci_unmap_cfg(void *ptr)
{
pci_ecam_free((struct pci_config_window *)ptr);
diff --git a/drivers/pci/controller/pci-host-common.h b/drivers/pci/controller/pci-host-common.h
index b5075d4bd7eb..37714bedb625 100644
--- a/drivers/pci/controller/pci-host-common.h
+++ b/drivers/pci/controller/pci-host-common.h
@@ -12,6 +12,22 @@
struct pci_ecam_ops;
+/**
+ * struct pci_host_port - Generic Root Port properties
+ * @list: List node for linking multiple ports
+ * @reset: GPIO descriptor for PERST# signal
+ *
+ * This structure contains common properties that can be parsed from
+ * Root Port device tree nodes.
+ */
+struct pci_host_port {
+ struct list_head list;
+ struct gpio_desc *reset;
+};
+
+void pci_host_common_delete_ports(void *data);
+int pci_host_common_parse_ports(struct device *dev, struct pci_host_bridge *bridge);
+
int pci_host_common_probe(struct platform_device *pdev);
int pci_host_common_init(struct platform_device *pdev,
struct pci_host_bridge *bridge,
diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
index eaa4a3d662e8..629ae08b7d35 100644
--- a/drivers/pci/probe.c
+++ b/drivers/pci/probe.c
@@ -677,6 +677,7 @@ static void pci_init_host_bridge(struct pci_host_bridge *bridge)
{
INIT_LIST_HEAD(&bridge->windows);
INIT_LIST_HEAD(&bridge->dma_ranges);
+ INIT_LIST_HEAD(&bridge->ports);
/*
* We assume we can manage these PCIe features. Some systems may
diff --git a/include/linux/pci.h b/include/linux/pci.h
index 8f63de38f2d2..a73ea81ce88f 100644
--- a/include/linux/pci.h
+++ b/include/linux/pci.h
@@ -636,6 +636,7 @@ struct pci_host_bridge {
int domain_nr;
struct list_head windows; /* resource_entry */
struct list_head dma_ranges; /* dma ranges resource list */
+ struct list_head ports; /* Root Port list (pci_host_port) */
#ifdef CONFIG_PCI_IDE
u16 nr_ide_streams; /* Max streams possibly active in @ide_stream_ida */
struct ida ide_stream_ida;
--
2.37.1
^ permalink raw reply related
* [PATCH V11 01/12] dt-bindings: PCI: fsl,imx6q-pcie: Add reset GPIO in Root Port node
From: Sherry Sun @ 2026-04-07 10:41 UTC (permalink / raw)
To: robh, krzk+dt, conor+dt, Frank.Li, s.hauer, kernel, festevam,
lpieralisi, kwilczynski, mani, bhelgaas, hongxing.zhu, l.stach
Cc: imx, linux-pci, linux-arm-kernel, devicetree, linux-kernel
In-Reply-To: <20260407104154.2842132-1-sherry.sun@nxp.com>
Update fsl,imx6q-pcie.yaml to include the standard reset-gpios property
for the Root Port node.
The reset-gpios property is already defined in pci-bus-common.yaml for
PERST#, so use it instead of the local reset-gpio property. Keep the
existing reset-gpio property in the bridge node for backward
compatibility, but mark it as deprecated.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
---
.../bindings/pci/fsl,imx6q-pcie.yaml | 32 +++++++++++++++++++
1 file changed, 32 insertions(+)
diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
index 12a01f7a5744..d1a2526f43dc 100644
--- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
+++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
@@ -59,16 +59,34 @@ properties:
- const: dma
reset-gpio:
+ deprecated: true
description: Should specify the GPIO for controlling the PCI bus device
reset signal. It's not polarity aware and defaults to active-low reset
sequence (L=reset state, H=operation state) (optional required).
+ This property is deprecated, instead of referencing this property from the
+ host bridge node, use the reset-gpios property from the root port node.
reset-gpio-active-high:
+ deprecated: true
description: If present then the reset sequence using the GPIO
specified in the "reset-gpio" property is reversed (H=reset state,
L=operation state) (optional required).
+ This property is deprecated along with the reset-gpio property above, use
+ the reset-gpios property from the root port node.
type: boolean
+ pcie@0:
+ description:
+ Describe the i.MX6 PCIe Root Port.
+ type: object
+ $ref: /schemas/pci/pci-pci-bridge.yaml#
+
+ properties:
+ reg:
+ maxItems: 1
+
+ unevaluatedProperties: false
+
required:
- compatible
- reg
@@ -229,6 +247,7 @@ unevaluatedProperties: false
examples:
- |
#include <dt-bindings/clock/imx6qdl-clock.h>
+ #include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
pcie: pcie@1ffc000 {
@@ -255,5 +274,18 @@ examples:
<&clks IMX6QDL_CLK_LVDS1_GATE>,
<&clks IMX6QDL_CLK_PCIE_REF_125M>;
clock-names = "pcie", "pcie_bus", "pcie_phy";
+
+ pcie_port0: pcie@0 {
+ compatible = "pciclass,0604";
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ bus-range = <0x01 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
+ };
};
...
--
2.37.1
^ permalink raw reply related
* [PATCH V11 00/12] pci-imx6: Add support for parsing the reset property in new Root Port binding
From: Sherry Sun @ 2026-04-07 10:41 UTC (permalink / raw)
To: robh, krzk+dt, conor+dt, Frank.Li, s.hauer, kernel, festevam,
lpieralisi, kwilczynski, mani, bhelgaas, hongxing.zhu, l.stach
Cc: imx, linux-pci, linux-arm-kernel, devicetree, linux-kernel
This patch set adds support for parsing the reset property in new Root Port
binding in pci-imx6 driver, similar to the implementation in the qcom pcie
driver[1].
Also introduce generic helper functions to parse Root Port device tree
nodes and extract common properties like reset GPIOs. This allows multiple
PCI host controller drivers to share the same parsing logic.
Define struct pci_host_port to hold common Root Port properties
(currently only reset GPIO descriptor) and add
pci_host_common_parse_ports() to parse Root Port nodes from device tree.
Also add the 'ports' list to struct pci_host_bridge for better maintain
parsed Root Port information.
The plan is to add the wake-gpio property to the root port in subsequent
patches. Also, the vpcie-supply property will be moved to the root port
node later based on the refactoring patch set for the PCI pwrctrl
framework[2].
The initial idea is to adopt the Manivannan’s recent PCIe M.2 KeyE
connector support patch set[3] and PCI power control framework patches[2],
and extend them to the pcie-imx6 driver. Since the new M.2/pwrctrl model is
implemented based on Root Ports and requires the pwrctrl driver to bind to
a Root Port device, we need to introduce a Root Port child node on i.MX
boards that provide an M.2 connector.
To follow a more standardized DT structure, it also makes sense to move
the reset-gpios and wake-gpios properties into the Root Port node. These
signals logically belong to the Root Port rather than the host bridge,
and placing them there aligns with the new M.2/pwrctrl model.
Regarding backward compatibility, as Frank suggested, I will not remove
the old reset-gpio property from existing DTS files to avoid function
break.
For new i.MX platforms — such as the upcoming i.MX952-evk will add
vpcie-supply, reset-gpios, and wake-gpios directly under the Root Port
node.
Therefore, driver updates are needed to support both the legacy
properties and the new standardized Root Port based layout.
[1] https://lore.kernel.org/linux-pci/20250702-perst-v5-0-920b3d1f6ee1@qti.qualcomm.com/
[2] https://lore.kernel.org/linux-pci/20260115-pci-pwrctrl-rework-v5-0-9d26da3ce903@oss.qualcomm.com/
[3] https://lore.kernel.org/linux-pci/20260112-pci-m2-e-v4-0-eff84d2c6d26@oss.qualcomm.com/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
Changes in V11:
1. Call pci_host_common_parse_ports() API from pci-imx6 driver instead of dwc
common layer as Mani suggested.
2. Improve the commit message of patch#3 to avoid confusion as Mani suggested.
Changes in V10:
1. Use gpiod_direction_output() instead of gpiod_set_value_cansleep() to
ensure the reset GPIO is properly configured as output before setting
its value in patch#5 as now the reset GPIO is obtained with
GPIOD_ASIS flag.
Changes in V9:
1. Improve the error handling in pci_host_common_parse_ports() as Mani suggested.
2. Move the list_empty check and the comment to imx_pcie_host_init() to make it
clear that imx_pcie_parse_legacy_binding() is a fallback as Mani suggested.
3. Export pci_host_common_delete_ports() so that it can be called by
imx_pcie_parse_legacy_binding().
Changes in V8:
1. Add back the cleanup function pci_host_common_delete_ports() to properly
handles the ports list instead of simply using pci_free_resource_list().
2. Improve the patch#4 commit message.
3. Remove the irrelevant code change in patch#4.
Changes in V7:
1. Change to use GPIOD_ASIS when requesting perst gpio as Mani suggested.
using bridge->dev.
2. Add a seperate patch to move vpcie3v3aux regulator enable from probe to
imx_pcie_host_init() and move imx_pcie_assert_perst() before regulator and
clock enable for pci-imx6.
3. Add device pointer parameter for pci_host_common_parse_port() instead of
Changes in V6:
1. Drop the pre-allocate pci_host_bridge struct changes in dw_pcie_host_init()
and imx_pcie_probe().
2. Parse Root Port nodes in dw_pcie_host_init() as Frank and Mani suggested.
3. Move the imx_pcie_parse_legacy_binding() from imx_pcie_probe() to
imx_pcie_host_init(), so that dw_pcie_host_init() parse Root Port first, if
no Root Port nodes were parsed(indicated by empty ports list), then parse
legacy binding.
4. Add device pointer parameter for pci_host_common_parse_ports().
5. Add NULL pointer check for reset gpio in imx_pcie_parse_legacy_binding().
Changes in V5:
1. Add the Root Port list(pci_host_port) to struct pci_host_bridge for better
maintain parsed Root Port information.
2. Delete the pci_host_common_delete_ports() as now the Root Port list in
pci_host_bridge can be cleared by pci_release_host_bridge_dev().
3. Change the common API pci_host_common_parse_ports() pass down struct
pci_host_bridge *.
4. Modify dw_pcie_host_init() to allow drivers to pre-allocate pci_host_bridge
struct when needed.
5. Allocate bridge early in imx_pcie_probe() to parse Root Ports.
Changes in V4:
1. Add common helpers for parsing Root Port properties in pci-host-common.c in
patch#2.
2. Call common pci_host_common_parse_ports() and pci_host_common_delete_ports()
in pci-imx6 driver.
3. Use PCIE_T_PVPERL_MS and PCIE_RESET_CONFIG_WAIT_MS instead of magic number
100 in patch#3 as Manivannan suggested.
4. Use "PERST#" instead of "PCIe reset" for the reset gpio lable in patch#3.
Changes in V3:
1. Improve the patch#2 commit message as Frank suggested.
2. Add Reviewed-by tag for patch#1.
Changes in V2:
1. Improve the patch#1 commit message as Frank suggested.
2. Also mark the reset-gpio-active-high property as deprecated in
imx6q-pcie DT binding as Rob suggested.
3. The imx_pcie_delete_ports() has been moved up so that the
imx_pcie_parse_ports() can call this helper function in error handling.
4. Keep the old reset-gpio property in the host bridge node for the
existing dts files and add comments to avoid confusion.
---
Sherry Sun (12):
dt-bindings: PCI: fsl,imx6q-pcie: Add reset GPIO in Root Port node
PCI: host-generic: Add common helpers for parsing Root Port properties
PCI: imx6: Assert PERST# before enabling regulators
PCI: imx6: Add support for parsing the reset property in new Root Port
binding
arm: dts: imx6qdl: Add Root Port node and PERST property
arm: dts: imx6sx: Add Root Port node and PERST property
arm: dts: imx7d: Add Root Port node and PERST property
arm64: dts: imx8mm: Add Root Port node and PERST property
arm64: dts: imx8mp: Add Root Port node and PERST property
arm64: dts: imx8mq: Add Root Port node and PERST property
arm64: dts: imx8dxl/qm/qxp: Add Root Port node and PERST property
arm64: dts: imx95: Add Root Port node and PERST property
.../bindings/pci/fsl,imx6q-pcie.yaml | 32 +++++
.../arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi | 5 +
arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi | 11 ++
.../arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts | 5 +
arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi | 5 +
arch/arm/boot/dts/nxp/imx/imx6sx.dtsi | 11 ++
arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts | 5 +
arch/arm/boot/dts/nxp/imx/imx7d.dtsi | 11 ++
.../boot/dts/freescale/imx8-ss-hsio.dtsi | 11 ++
arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 5 +
arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi | 5 +
arch/arm64/boot/dts/freescale/imx8mm.dtsi | 11 ++
arch/arm64/boot/dts/freescale/imx8mp-evk.dts | 5 +
arch/arm64/boot/dts/freescale/imx8mp.dtsi | 11 ++
arch/arm64/boot/dts/freescale/imx8mq-evk.dts | 10 ++
arch/arm64/boot/dts/freescale/imx8mq.dtsi | 22 ++++
arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 10 ++
.../boot/dts/freescale/imx8qm-ss-hsio.dtsi | 22 ++++
arch/arm64/boot/dts/freescale/imx8qxp-mek.dts | 5 +
.../boot/dts/freescale/imx95-15x15-evk.dts | 5 +
.../boot/dts/freescale/imx95-19x19-evk.dts | 10 ++
arch/arm64/boot/dts/freescale/imx95.dtsi | 22 ++++
drivers/pci/controller/dwc/pci-imx6.c | 124 ++++++++++++++----
drivers/pci/controller/pci-host-common.c | 77 +++++++++++
drivers/pci/controller/pci-host-common.h | 16 +++
drivers/pci/probe.c | 1 +
include/linux/pci.h | 1 +
27 files changed, 433 insertions(+), 25 deletions(-)
--
2.37.1
^ permalink raw reply
* Re: [PATCH WIP v3 11/11] arm64: dts: qcom: sdm845-google: Add STM FTS touchscreen support
From: Konrad Dybcio @ 2026-04-07 10:40 UTC (permalink / raw)
To: david, Dmitry Torokhov, Maxime Coquelin, Alexandre Torgue,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Henrik Rydberg,
Bjorn Andersson, Konrad Dybcio
Cc: Petr Hodina, linux-input, linux-stm32, linux-arm-kernel,
linux-kernel, Krzysztof Kozlowski, devicetree, linux-arm-msm,
phone-devel
In-Reply-To: <20260403-stmfts5-v3-11-5da768cfd201@ixit.cz>
On 4/3/26 7:08 PM, David Heidelberg via B4 Relay wrote:
> From: Petr Hodina <petr.hodina@protonmail.com>
>
> Basic touchscreen connected to second i2c bus.
I was really hoping for an advanced touchscreen!
> Signed-off-by: Petr Hodina <petr.hodina@protonmail.com>
> Co-developed-by: David Heidelberg <david@ixit.cz>
> Signed-off-by: David Heidelberg <david@ixit.cz>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Konrad
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox