* [PATCH v3 0/4] arm64: dts: rockchip: add Forlinx OK3568-C
@ 2026-11-18 23:29 Dmitry Yashin
2026-11-18 23:29 ` [PATCH v3 1/4] dt-bindings: arm: rockchip: add Forlinx FET3568-C Dmitry Yashin
` (3 more replies)
0 siblings, 4 replies; 6+ messages in thread
From: Dmitry Yashin @ 2026-11-18 23:29 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
Cc: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel,
Krzysztof Kozlowski, Dmitry Yashin
This series add support for Forlinx OK3568-C board based on FET3568-C SoM
(rk3568). Patches 1-3 add .dtsi for FET3568-C and .dts for OK3568-C.
Patch 4 adds .dtso for FIT-PCIE-SATA adapter that allows to connect
SATA drives to the board.
Note: tested on v1.1 board. On v1.2 RTL8211F phys use dedicated
crystal oscillator instead of 25 MHz reference clock from SoC. Patch
should be compatible with both revisions, as in [1] solution.
[1] https://lore.kernel.org/all/20250704-rk3576-rock4d-phy-handling-fixes-v1-1-1d64130c4139@kernel.org/
---
Changes in v3:
- dropped rfkill-gpio dt-binding patch as not appropriate
- dropped rfkill-gpio node from the board's device tree
- Link to v2: https://patch.msgid.link/20261016-ok3568-c-v2-0-068d68430e6d@gmail.com
Changes in v2:
- added patch for rfkill-gpio's dt-binding with reset-gpios property to
suppress dt warnings
- removed mmc-pwrseq. AW-CM358SM has only power management PDn pin
for both wifi and bt. Using shared wifi_bt_reg_on regulator fixes
bluetooth failure on cold boots
- added bluetooth wakein/wakeout pins
- moved leds/common.h to the SoM dtsi
- switched gmac's phy-mode to rgmii-id
- added rfkill-gpio for modem reset
- dropped unused wifi and bt pinctrl's
- Link to v1: https://patch.msgid.link/20260930-ok3568-c-v1-0-a0ffd55f5c95@gmail.com
To: Rob Herring <robh@kernel.org>
To: Krzysztof Kozlowski <krzk+dt@kernel.org>
To: Conor Dooley <conor+dt@kernel.org>
To: Heiko Stuebner <heiko@sntech.de>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
---
Dmitry Yashin (4):
dt-bindings: arm: rockchip: add Forlinx FET3568-C
arm64: dts: rockchip: add Forlinx FET3568-C
arm64: dts: rockchip: add Forlinx OK3568-C
arm64: dts: rockchip: add FIT-PCIE-SATA overlay
.../devicetree/bindings/arm/rockchip.yaml | 7 +
arch/arm64/boot/dts/rockchip/Makefile | 6 +
arch/arm64/boot/dts/rockchip/rk3568-fet3568-c.dtsi | 332 ++++++++++++
.../rockchip/rk3568-ok3568-c-fit-pcie-sata.dtso | 16 +
arch/arm64/boot/dts/rockchip/rk3568-ok3568-c.dts | 566 +++++++++++++++++++++
5 files changed, 927 insertions(+)
---
base-commit: 72d3fcf802c45d00b300f25b848a93c3a2bd7c7e
change-id: 20260930-ok3568-c-c095925b1e26
Best regards,
--
Dmitry Yashin <dmt.yashin@gmail.com>
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v3 1/4] dt-bindings: arm: rockchip: add Forlinx FET3568-C
2026-11-18 23:29 [PATCH v3 0/4] arm64: dts: rockchip: add Forlinx OK3568-C Dmitry Yashin
@ 2026-11-18 23:29 ` Dmitry Yashin
2026-11-18 23:29 ` [PATCH v3 2/4] arm64: dts: " Dmitry Yashin
` (2 subsequent siblings)
3 siblings, 0 replies; 6+ messages in thread
From: Dmitry Yashin @ 2026-11-18 23:29 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
Cc: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel,
Krzysztof Kozlowski, Dmitry Yashin
FET3568-C is an System on Module made by Forlinx based on Rockchip RK3568.
This SoM used by OK3568-C Board.
FET3568-C features:
- Rockchip RK3568
- DDR4 1/2/4/8 GB
- eMMC 8/16/32/64 GB
- RK809 PMIC
Add devicetree binding for Forlinx FET3568-C SoM.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Dmitry Yashin <dmt.yashin@gmail.com>
---
Documentation/devicetree/bindings/arm/rockchip.yaml | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index a799bb843f74..30a6794861cc 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -324,6 +324,13 @@ properties:
- const: firefly,rk3568-roc-pc
- const: rockchip,rk3568
+ - description: Forlinx FET3568-C SoM
+ items:
+ - enum:
+ - forlinx,ok3568-c
+ - const: forlinx,fet3568-c
+ - const: rockchip,rk3568
+
- description: Forlinx FET3588-C SoM
items:
- enum:
--
2.56.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v3 2/4] arm64: dts: rockchip: add Forlinx FET3568-C
2026-11-18 23:29 [PATCH v3 0/4] arm64: dts: rockchip: add Forlinx OK3568-C Dmitry Yashin
2026-11-18 23:29 ` [PATCH v3 1/4] dt-bindings: arm: rockchip: add Forlinx FET3568-C Dmitry Yashin
@ 2026-11-18 23:29 ` Dmitry Yashin
2026-11-18 23:29 ` [PATCH v3 3/4] arm64: dts: rockchip: add Forlinx OK3568-C Dmitry Yashin
2026-11-18 23:29 ` [PATCH v3 4/4] arm64: dts: rockchip: add FIT-PCIE-SATA overlay Dmitry Yashin
3 siblings, 0 replies; 6+ messages in thread
From: Dmitry Yashin @ 2026-11-18 23:29 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
Cc: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel,
Dmitry Yashin
FET3568-C is an System on Module made by Forlinx based on Rockchip RK3568.
This SoM used by OK3568-C Board.
FET3568-C features:
- Rockchip RK3568
- DDR4 1/2/4/8 GB
- eMMC 8/16/32/64 GB
- RK809 PMIC
Add devicetree for Forlinx FET3568-C SoM.
Signed-off-by: Dmitry Yashin <dmt.yashin@gmail.com>
---
arch/arm64/boot/dts/rockchip/rk3568-fet3568-c.dtsi | 332 +++++++++++++++++++++
1 file changed, 332 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-fet3568-c.dtsi b/arch/arm64/boot/dts/rockchip/rk3568-fet3568-c.dtsi
new file mode 100644
index 000000000000..9a3e810c46b5
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3568-fet3568-c.dtsi
@@ -0,0 +1,332 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "rk3568.dtsi"
+
+/ {
+ compatible = "forlinx,fet3568-c", "rockchip,rk3568";
+
+ aliases {
+ mmc0 = &sdhci;
+ };
+
+ chosen: chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ color = <LED_COLOR_ID_BLUE>;
+ default-state = "on";
+ function = LED_FUNCTION_HEARTBEAT;
+ gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led0_pin>;
+ };
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ vdd_cpu: regulator@1c {
+ compatible = "tcs,tcs4525";
+ reg = <0x1c>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc5v0>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk809: pmic@20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+ assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+ #clock-cells = <1>;
+ clocks = <&cru I2S1_MCLKOUT_TX>;
+ clock-names = "mclk";
+ clock-output-names = "rk809-clkout1", "rk809-clkout2";
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int>, <&i2s1m0_mclk>;
+ #sound-dai-cells = <0>;
+ system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc3v3>;
+ vcc2-supply = <&vcc3v3>;
+ vcc3-supply = <&vcc3v3>;
+ vcc4-supply = <&vcc3v3>;
+ vcc5-supply = <&vcc3v3>;
+ vcc6-supply = <&vcc3v3>;
+ vcc7-supply = <&vcc3v3>;
+ vcc8-supply = <&vcc3v3>;
+ vcc9-supply = <&vcc3v3>;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-name = "vdd_logic";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-name = "vdd_gpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdd_npu: DCDC_REG4 {
+ regulator-name = "vdd_npu";
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG5 {
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_image: LDO_REG1 {
+ regulator-name = "vdda0v9_image";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda_0v9: LDO_REG2 {
+ regulator-name = "vdda_0v9";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-name = "vdda0v9_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-name = "vccio_acodec";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-name = "vccio_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-name = "vcc3v3_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcca_1v8: LDO_REG7 {
+ regulator-name = "vcca_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG8 {
+ regulator-name = "vcca1v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcca1v8_image: LDO_REG9 {
+ regulator-name = "vcca1v8_image";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v3: SWITCH_REG1 {
+ regulator-name = "vcc_3v3";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_sd: SWITCH_REG2 {
+ regulator-name = "vcc3v3_sd";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&pinctrl {
+ leds {
+ led0_pin: led0-pin {
+ rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int: pmic-int {
+ rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
+
+&sdhci {
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ max-frequency = <200000000>;
+ mmc-hs200-1_8v;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <0>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
--
2.56.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v3 3/4] arm64: dts: rockchip: add Forlinx OK3568-C
2026-11-18 23:29 [PATCH v3 0/4] arm64: dts: rockchip: add Forlinx OK3568-C Dmitry Yashin
2026-11-18 23:29 ` [PATCH v3 1/4] dt-bindings: arm: rockchip: add Forlinx FET3568-C Dmitry Yashin
2026-11-18 23:29 ` [PATCH v3 2/4] arm64: dts: " Dmitry Yashin
@ 2026-11-18 23:29 ` Dmitry Yashin
2026-11-18 23:53 ` sashiko-bot
2026-11-18 23:29 ` [PATCH v3 4/4] arm64: dts: rockchip: add FIT-PCIE-SATA overlay Dmitry Yashin
3 siblings, 1 reply; 6+ messages in thread
From: Dmitry Yashin @ 2026-11-18 23:29 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
Cc: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel,
Dmitry Yashin
OK3568-C is the carrier board for FET3568-C System on Module.
OK3568-C features:
2x 1GbE Realtek RTL8211F Ethernet
1x HDMI Type A out
1x Edp and LVDS headers
2x USB Type C (2.0 and debug console)
1x USB 3.0 OTG Type A (2.0 part is multiplexed with Type C)
1x USB 3.0 M.2 M Key (4G/5G modem)
2x USB 2.0 Type A
1x PCIE 3.0 PCIe (2 lanes)
1x PCIE 2.1 PCIe (1 lane)
1x TF scard slot
1x MIPI CSI
1x MIPI DSI
2x CAN 2.0
1x RTC
1x earphone output and Speaker output, 1x mic.
50-pin expansion header
ADC keys
onboard WiFi And BT (AW-CM358SM)
Add support for Forlinx OK3568-C board.
Signed-off-by: Dmitry Yashin <dmt.yashin@gmail.com>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
arch/arm64/boot/dts/rockchip/rk3568-ok3568-c.dts | 566 +++++++++++++++++++++++
2 files changed, 567 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index e7936a21c118..48c83f79f83b 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -155,6 +155,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-mecsbc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5c.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5s.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-odroid-m1.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-ok3568-c.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-photonicat.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-qnap-ts233.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-qnap-ts233-pcb-12-11.dtbo
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-ok3568-c.dts b/arch/arm64/boot/dts/rockchip/rk3568-ok3568-c.dts
new file mode 100644
index 000000000000..94f08fdc1143
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3568-ok3568-c.dts
@@ -0,0 +1,566 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3568-fet3568-c.dtsi"
+
+/ {
+ model = "Forlinx OK3568-C";
+ compatible = "forlinx,ok3568-c", "forlinx,fet3568-c", "rockchip,rk3568";
+
+ aliases {
+ ethernet0 = &gmac0;
+ ethernet1 = &gmac1;
+ mmc1 = &sdmmc0;
+ };
+
+ adc-keys-0 {
+ compatible = "adc-keys";
+ io-channels = <&saradc 0>;
+ io-channel-names = "buttons";
+ keyup-threshold-microvolt = <1750000>;
+ poll-interval = <100>;
+
+ button-volume-up {
+ label = "V+/Recovery";
+ linux,code = <KEY_VOLUMEUP>;
+ press-threshold-microvolt = <1750>;
+ };
+
+ button-volume-down {
+ label = "V-";
+ linux,code = <KEY_VOLUMEDOWN>;
+ press-threshold-microvolt = <297500>;
+ };
+
+ button-menu {
+ label = "Menu";
+ linux,code = <KEY_MENU>;
+ press-threshold-microvolt = <980000>;
+ };
+
+ button-escape {
+ label = "ESC";
+ linux,code = <KEY_ESC>;
+ press-threshold-microvolt = <1305500>;
+ };
+ };
+
+ hdmi-con {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ /* DSC557-0344FI1 clock generator */
+ pcie30_refclk: pcie-clock-generator {
+ compatible = "gated-fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ clock-output-names = "pcie30_refclk";
+ vdd-supply = <&vcc3v3_pi6c_oe>;
+ };
+
+ rk809-sound {
+ compatible = "simple-audio-card";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hp_detect>;
+ simple-audio-card,name = "Analog RK809";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,hp-det-gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
+ simple-audio-card,mclk-fs = <256>;
+ simple-audio-card,widgets =
+ "Headphone", "Headphones",
+ "Speaker", "Speaker",
+ "Microphone", "Onboard Microphone",
+ "Microphone", "Headset Microphone";
+ simple-audio-card,routing =
+ "Headphones", "HPOL",
+ "Headphones", "HPOR",
+ "Speaker", "SPKO",
+ "MICL", "Onboard Microphone",
+ "MICR", "Headset Microphone";
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1_8ch>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&rk809>;
+ };
+ };
+
+ vcc12v_dcin: regulator-12v-vcc-dcin {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc12v_dcin";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc1v8_wifi_bt_reg_on: regulator-1v8-vcc-wifi-bt-reg-on {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio3 RK_PD4 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_reg_on>;
+ off-on-delay-us = <20000>;
+ regulator-name = "vcc1v8_wifi_bt_reg_on";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ startup-delay-us = <200>;
+ };
+
+ vcc1v8: regulator-1v8-vcc {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc3v3>;
+ };
+
+ vcc3v3_pi6c_oe: regulator-3v3-vcc-pi6c-oe {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pi6c_oe>;
+ regulator-name = "vcc3v3_pi6c_oe";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <5000>;
+ };
+
+ vcc3v3_pcie20: regulator-3v3-vcc-pcie20 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_pcie20";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0>;
+ };
+
+ vcc3v3_pcie30: regulator-3v3-vcc-pcie30 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_pcie30";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0>;
+ };
+
+ vcc3v3: regulator-3v3-vcc {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0>;
+ };
+
+ vcc4v2_5g: regulator-4v2-vcc-5g {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio1 RK_PB1 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&modem_5g_pwr>;
+ regulator-name = "vcc4v2_5g";
+ regulator-min-microvolt = <4200000>;
+ regulator-max-microvolt = <4200000>;
+ startup-delay-us = <50000>;
+ vin-supply = <&vcc5v0>;
+ };
+
+ vcc5v0: regulator-5v0-vcc {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+};
+
+&can0 {
+ compatible = "rockchip,rk3568v3-canfd", "rockchip,rk3568v2-canfd";
+ assigned-clocks = <&cru CLK_CAN0>;
+ assigned-clock-rates = <300000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&can0m0_pins>;
+ status = "okay";
+};
+
+&can1 {
+ compatible = "rockchip,rk3568v3-canfd", "rockchip,rk3568v2-canfd";
+ assigned-clocks = <&cru CLK_CAN1>;
+ assigned-clock-rates = <300000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&can1m1_pins>;
+ status = "okay";
+};
+
+&combphy0 {
+ status = "okay";
+};
+
+&combphy1 {
+ status = "okay";
+};
+
+&combphy2 {
+ status = "okay";
+};
+
+&gmac0 {
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy0>;
+ phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac0_miim
+ &gmac0_tx_bus2
+ &gmac0_rx_bus2
+ &gmac0_rgmii_clk
+ &gmac0_rgmii_bus
+ &gmac0_clkinout
+ ð0_pins>;
+ status = "okay";
+};
+
+&gmac1 {
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy1>;
+ phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1m1_miim
+ &gmac1m1_tx_bus2
+ &gmac1m1_rx_bus2
+ &gmac1m1_rgmii_clk
+ &gmac1m1_rgmii_bus
+ &gmac1m1_clkinout
+ ð1m1_pins>;
+ status = "okay";
+};
+
+&hdmi {
+ avdd-0v9-supply = <&vdda0v9_image>;
+ avdd-1v8-supply = <&vcca1v8_image>;
+ status = "okay";
+};
+
+&hdmi_in {
+ hdmi_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi>;
+ };
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&hdmi_sound {
+ status = "okay";
+};
+
+&i2c3 {
+ status = "okay";
+
+ pcf8563: rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&i2s0_8ch {
+ status = "okay";
+};
+
+&i2s1_8ch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1m0_sclktx
+ &i2s1m0_lrcktx
+ &i2s1m0_sdi0
+ &i2s1m0_sdo0>;
+ rockchip,trcm-sync-tx-only;
+ status = "okay";
+};
+
+&mdio0 {
+ rgmii_phy0: ethernet-phy@1 {
+ compatible = "ethernet-phy-id001c.c916";
+ reg = <0x1>;
+ clocks = <&cru CLK_MAC0_OUT>;
+ assigned-clocks = <&cru CLK_MAC0_OUT>;
+ assigned-clock-rates = <25000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_phy0_rst>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <100000>;
+ reset-gpios = <&gpio3 RK_PA4 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&mdio1 {
+ rgmii_phy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-id001c.c916";
+ reg = <0x1>;
+ clocks = <&cru CLK_MAC1_OUT>;
+ assigned-clocks = <&cru CLK_MAC1_OUT>;
+ assigned-clock-rates = <25000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_phy1_rst>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <100000>;
+ reset-gpios = <&gpio3 RK_PA2 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&pcie2x1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie20m0_pins>;
+ reset-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_pcie20>;
+ status = "okay";
+};
+
+&pcie30phy {
+ status = "okay";
+};
+
+&pcie3x2 {
+ clocks = <&cru ACLK_PCIE30X2_MST>, <&cru ACLK_PCIE30X2_SLV>,
+ <&cru ACLK_PCIE30X2_DBI>, <&cru PCLK_PCIE30X2>,
+ <&cru CLK_PCIE30X2_AUX_NDFT>,
+ <&cru CLK_PCIE30X2_PIPE_DFT>,
+ <&pcie30_refclk>;
+ clock-names = "aclk_mst", "aclk_slv",
+ "aclk_dbi", "pclk", "aux",
+ "pipe", "ref";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie30x2m0_pins>;
+ reset-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_pcie30>;
+ status = "okay";
+};
+
+&pinctrl {
+ bluetooth {
+ bt_wake_host: bt-wake-host {
+ rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ host_wake_bt: host-wake-bt {
+ rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ ethernet {
+ rgmii_phy0_rst: rgmii-phy0-rst {
+ rockchip,pins = <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ rgmii_phy1_rst: rgmii-phy1-rst {
+ rockchip,pins = <3 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ modem {
+ modem_5g_pwr: modem-5g-pwr {
+ rockchip,pins = <1 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ /* Drop pcie20_clkreqnm0 pin. Used as DSC557-0344FI1 enable-gpio instead. */
+ pcie20 {
+ pcie20m0_pins: pcie20m0-pins {
+ rockchip,pins =
+ /* pcie20_perstnm0 */
+ <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>,
+ /* pcie20_wakenm0 */
+ <0 RK_PB5 3 &pcfg_pull_none>;
+ };
+ };
+
+ pcie30x2 {
+ pcie30x2m0_pins: pcie30x2m0-pins {
+ rockchip,pins =
+ /* pcie30x2_clkreqnm0 */
+ <0 RK_PA6 2 &pcfg_pull_none>,
+ /* pcie30x2_perstnm0 */
+ <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>,
+ /* pcie30x2_wakenm0 */
+ <0 RK_PC5 3 &pcfg_pull_none>;
+ };
+
+ pi6c_oe: pi6c-oe {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sound {
+ hp_detect: hp-detect {
+ rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ wifi {
+ wifi_reg_on: wifi-reg-on {
+ rockchip,pins = <3 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmuio1-supply = <&vcc3v3_pmu>;
+ pmuio2-supply = <&vcc3v3_pmu>;
+ vccio1-supply = <&vccio_acodec>;
+ vccio2-supply = <&vcc_1v8>;
+ vccio3-supply = <&vccio_sd>;
+ vccio4-supply = <&vcc_1v8>;
+ vccio5-supply = <&vcc_3v3>;
+ vccio6-supply = <&vcc_1v8>;
+ vccio7-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcca_1v8>;
+ status = "okay";
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ disable-wp;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc3v3_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+/* WiFi part of the AW-CM358SM connected with SDIO */
+&sdmmc2 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc2m0_bus4 &sdmmc2m0_clk &sdmmc2m0_cmd>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc3v3>;
+ vqmmc-supply = <&vcc1v8_wifi_bt_reg_on>;
+ status = "okay";
+};
+
+/* BT part of the AW-CM358SM connected with UART */
+&uart8 {
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart8m0_xfer &uart8m0_ctsn &uart8m0_rtsn>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "nxp,88w8987-bt";
+ device-wakeup-gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PD3 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-names = "wakeup";
+ nxp,wakein-pin = /bits/ 8 <18>;
+ nxp,wakeout-pin = /bits/ 8 <19>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_wake_host &host_wake_bt>;
+ vcc-supply = <&vcc1v8_wifi_bt_reg_on>;
+ wakeup-source;
+ };
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ extcon = <&usb2phy0>;
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usb_host1_xhci {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usb2phy0 {
+ status = "okay";
+};
+
+&usb2phy0_host {
+ phy-supply = <&vcc4v2_5g>;
+ status = "okay";
+};
+
+&usb2phy0_otg {
+ phy-supply = <&vcc5v0>;
+ status = "okay";
+};
+
+&usb2phy1 {
+ status = "okay";
+};
+
+&usb2phy1_host {
+ phy-supply = <&vcc5v0>;
+ status = "okay";
+};
+
+&usb2phy1_otg {
+ phy-supply = <&vcc5v0>;
+ status = "okay";
+};
+
+&vop {
+ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi_in_vp0>;
+ };
+};
--
2.56.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v3 4/4] arm64: dts: rockchip: add FIT-PCIE-SATA overlay
2026-11-18 23:29 [PATCH v3 0/4] arm64: dts: rockchip: add Forlinx OK3568-C Dmitry Yashin
` (2 preceding siblings ...)
2026-11-18 23:29 ` [PATCH v3 3/4] arm64: dts: rockchip: add Forlinx OK3568-C Dmitry Yashin
@ 2026-11-18 23:29 ` Dmitry Yashin
3 siblings, 0 replies; 6+ messages in thread
From: Dmitry Yashin @ 2026-11-18 23:29 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
Cc: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel,
Dmitry Yashin
FIT-PCIE-SATA V1.0 is an adapter that included with OK3568-C board
and allows to connect SATA drives to the device.
Add overlay to use combphy2 in SATA mode.
Signed-off-by: Dmitry Yashin <dmt.yashin@gmail.com>
---
arch/arm64/boot/dts/rockchip/Makefile | 5 +++++
.../boot/dts/rockchip/rk3568-ok3568-c-fit-pcie-sata.dtso | 16 ++++++++++++++++
2 files changed, 21 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 48c83f79f83b..45e94a44107e 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -155,6 +155,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-mecsbc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5c.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5s.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-odroid-m1.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-ok3568-c-fit-pcie-sata.dtbo
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-ok3568-c.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-photonicat.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-qnap-ts233.dtb
@@ -275,6 +276,10 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-lion-haikou-haikou-video-demo.dtb
rk3368-lion-haikou-haikou-video-demo-dtbs := rk3368-lion-haikou.dtb \
rk3368-lion-haikou-video-demo.dtbo
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-ok3568-c-fit-pcie-sata.dtb
+rk3568-ok3568-c-fit-pcie-sata-dtbs := rk3568-ok3568-c.dtb \
+ rk3568-ok3568-c-fit-pcie-sata.dtbo
+
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou-haikou-video-demo.dtb
rk3399-puma-haikou-haikou-video-demo-dtbs := rk3399-puma-haikou.dtb \
rk3399-puma-haikou-video-demo.dtbo
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-ok3568-c-fit-pcie-sata.dtso b/arch/arm64/boot/dts/rockchip/rk3568-ok3568-c-fit-pcie-sata.dtso
new file mode 100644
index 000000000000..474488ea994b
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3568-ok3568-c-fit-pcie-sata.dtso
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * FIT-PCIE-SATA V1.0 is an adapter that included with OK3568-C
+ * board and allows to connect SATA drives to the device.
+ */
+
+/dts-v1/;
+/plugin/;
+
+&pcie2x1 {
+ status = "disabled";
+};
+
+&sata2 {
+ status = "okay";
+};
--
2.56.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v3 3/4] arm64: dts: rockchip: add Forlinx OK3568-C
2026-11-18 23:29 ` [PATCH v3 3/4] arm64: dts: rockchip: add Forlinx OK3568-C Dmitry Yashin
@ 2026-11-18 23:53 ` sashiko-bot
0 siblings, 0 replies; 6+ messages in thread
From: sashiko-bot @ 2026-11-18 23:53 UTC (permalink / raw)
To: Dmitry Yashin; +Cc: devicetree, robh, conor+dt
Thank you for your contribution! Sashiko AI review found 2 potential
issues to consider:
- [Medium] arm64: dts: rockchip: conflicting GPIO polarity in
vcc1v8_wifi_bt_reg_on
- [Medium] arm64: dts: rockchip: missing assigned-clocks on gmac0/1 in
rk3568-ok3568-c
--
commit b8a53fc702b227f666755566c4fdee7cf810512c
Author: Dmitry Yashin <dmt.yashin@gmail.com>
arm64: dts: rockchip: add Forlinx OK3568-C
This commit adds a devicetree for the Forlinx OK3568-C carrier board,
which hosts the FET3568-C System on Module.
> diff --git a/arch/arm64/boot/dts/rockchip/rk3568-ok3568-c.dts b/arch/arm64/boot/dts/rockchip/rk3568-ok3568-c.dts
> new file mode 100644
> index 0000000000000..94f08fdc11433
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3568-ok3568-c.dts
> @@ -0,0 +1,566 @@
[ ... ]
> + vcc1v8_wifi_bt_reg_on: regulator-1v8-vcc-wifi-bt-reg-on {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpios = <&gpio3 RK_PD4 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_reg_on>;
> + off-on-delay-us = <20000>;
> + regulator-name = "vcc1v8_wifi_bt_reg_on";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + startup-delay-us = <200>;
> + };
[Severity: Medium]
Does vcc1v8_wifi_bt_reg_on specify conflicting polarities with both
enable-active-high and GPIO_ACTIVE_LOW?
For regulator-fixed nodes with enable-active-high, of_gpio_quirk_polarity()
emits a runtime warning and strips OF_GPIO_ACTIVE_LOW. If the hardware
enable signal is active-low, enable-active-high should be dropped so the
regulator does not invert the polarity and keep the WiFi/BT module powered
off; if it is active-high, gpios should use GPIO_ACTIVE_HIGH.
[ ... ]
> +&gmac0 {
> + clock_in_out = "output";
> + phy-handle = <&rgmii_phy0>;
> + phy-mode = "rgmii-id";
> + pinctrl-names = "default";
> + pinctrl-0 = <&gmac0_miim
> + &gmac0_tx_bus2
> + &gmac0_rx_bus2
> + &gmac0_rgmii_clk
> + &gmac0_rgmii_bus
> + &gmac0_clkinout
> + ð0_pins>;
> + status = "okay";
> +};
> +
> +&gmac1 {
> + clock_in_out = "output";
> + phy-handle = <&rgmii_phy1>;
> + phy-mode = "rgmii-id";
> + pinctrl-names = "default";
> + pinctrl-0 = <&gmac1m1_miim
> + &gmac1m1_tx_bus2
> + &gmac1m1_rx_bus2
> + &gmac1m1_rgmii_clk
> + &gmac1m1_rgmii_bus
> + &gmac1m1_clkinout
> + ð1m1_pins>;
> + status = "okay";
> +};
[Severity: Medium]
Should gmac0 and gmac1 configure assigned-clocks, assigned-clock-parents,
and assigned-clock-rates for RGMII clock output?
On RK3568, rk_gmac_clk_init() does not program the GMAC clock muxes or the
125 MHz base rate in RGMII output mode, and SCLK_GMAC0/1_RGMII_SPEED lacks
CLK_SET_RATE_PARENT so runtime link speed changes only switch dividers on
SCLK_GMAC0/1_RX_TX. Without assigned-clocks in the devicetree to parent
SCLK_GMAC0/1_RX_TX to SCLK_GMAC0/1_RGMII_SPEED and set SCLK_GMAC0/1 to
125 MHz (via CLK_MAC0/1_2TOP), RGMII clock generation depends on the
bootloader having already configured both clock trees.
--
Sashiko AI review · https://sashiko.dev/#/patchset/20261119-ok3568-c-v3-0-071840643591@gmail.com?part=3
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2026-11-18 23:53 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-11-18 23:29 [PATCH v3 0/4] arm64: dts: rockchip: add Forlinx OK3568-C Dmitry Yashin
2026-11-18 23:29 ` [PATCH v3 1/4] dt-bindings: arm: rockchip: add Forlinx FET3568-C Dmitry Yashin
2026-11-18 23:29 ` [PATCH v3 2/4] arm64: dts: " Dmitry Yashin
2026-11-18 23:29 ` [PATCH v3 3/4] arm64: dts: rockchip: add Forlinx OK3568-C Dmitry Yashin
2026-11-18 23:53 ` sashiko-bot
2026-11-18 23:29 ` [PATCH v3 4/4] arm64: dts: rockchip: add FIT-PCIE-SATA overlay Dmitry Yashin
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox