* [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support
@ 2026-05-17 7:43 Svyatoslav Ryhel
2026-05-17 7:43 ` [PATCH v1 1/6] dt-bindings: leds: Document TI LM3533 LED controller Svyatoslav Ryhel
` (6 more replies)
0 siblings, 7 replies; 18+ messages in thread
From: Svyatoslav Ryhel @ 2026-05-17 7:43 UTC (permalink / raw)
To: Lee Jones, Daniel Thompson, Jingoo Han, Pavel Machek, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Jonathan Cameron,
David Lechner, Nuno Sá, Andy Shevchenko, Helge Deller,
Svyatoslav Ryhel
Cc: dri-devel, linux-leds, devicetree, linux-kernel, linux-iio,
linux-fbdev
Convert LM3533 to OF bindings, add missing VIN supply, add support for
setting mapping mode and LED sources based on device tree.
Svyatoslav Ryhel (6):
dt-bindings: leds: Document TI LM3533 LED controller
mfd: lm3533: Convert to use OF bindings
mfd: lm3533: Add support for VIN power supply
mfd: lm3533: set DMA mask
video: backlight: lm3533_bl: Set initial mapping mode from DT
video: leds: backlight: lm3533: Support getting LED sources from DT
.../leds/backlight/ti,lm3533-backlight.yaml | 68 +++++
.../bindings/leds/ti,lm3533-leds.yaml | 66 ++++
.../devicetree/bindings/leds/ti,lm3533.yaml | 190 ++++++++++++
drivers/iio/light/lm3533-als.c | 123 +++-----
drivers/leds/leds-lm3533.c | 117 ++++++--
drivers/mfd/lm3533-core.c | 281 +++++++-----------
drivers/video/backlight/lm3533_bl.c | 123 ++++++--
include/linux/mfd/lm3533.h | 52 +---
8 files changed, 660 insertions(+), 360 deletions(-)
create mode 100644 Documentation/devicetree/bindings/leds/backlight/ti,lm3533-backlight.yaml
create mode 100644 Documentation/devicetree/bindings/leds/ti,lm3533-leds.yaml
create mode 100644 Documentation/devicetree/bindings/leds/ti,lm3533.yaml
--
2.51.0
^ permalink raw reply [flat|nested] 18+ messages in thread* [PATCH v1 1/6] dt-bindings: leds: Document TI LM3533 LED controller 2026-05-17 7:43 [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support Svyatoslav Ryhel @ 2026-05-17 7:43 ` Svyatoslav Ryhel 2026-05-17 13:44 ` Jonathan Cameron 2026-05-17 7:43 ` [PATCH v1 2/6] mfd: lm3533: Convert to use OF bindings Svyatoslav Ryhel ` (5 subsequent siblings) 6 siblings, 1 reply; 18+ messages in thread From: Svyatoslav Ryhel @ 2026-05-17 7:43 UTC (permalink / raw) To: Lee Jones, Daniel Thompson, Jingoo Han, Pavel Machek, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko, Helge Deller, Svyatoslav Ryhel Cc: dri-devel, linux-leds, devicetree, linux-kernel, linux-iio, linux-fbdev Document the LM3533 - a complete power source for backlight, keypad and indicator LEDs in smartphone handsets. The high-voltage inductive boost converter provides the power for two series LED strings display backlight and keypad functions. Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> --- .../leds/backlight/ti,lm3533-backlight.yaml | 68 +++++++ .../bindings/leds/ti,lm3533-leds.yaml | 66 ++++++ .../devicetree/bindings/leds/ti,lm3533.yaml | 190 ++++++++++++++++++ 3 files changed, 324 insertions(+) create mode 100644 Documentation/devicetree/bindings/leds/backlight/ti,lm3533-backlight.yaml create mode 100644 Documentation/devicetree/bindings/leds/ti,lm3533-leds.yaml create mode 100644 Documentation/devicetree/bindings/leds/ti,lm3533.yaml diff --git a/Documentation/devicetree/bindings/leds/backlight/ti,lm3533-backlight.yaml b/Documentation/devicetree/bindings/leds/backlight/ti,lm3533-backlight.yaml new file mode 100644 index 000000000000..866b0fb8ed04 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/backlight/ti,lm3533-backlight.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/leds/backlight/ti,lm3533-backlight.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TI LM3533 high voltage series LED strings + +description: + This is part of the TI LM3533 MFD device. It represents two high voltage series + LED strings for display backlight controlled by the TI LM3533. + +maintainers: + - Svyatoslav Ryhel <clamor95@gmail.com> + +allOf: + - $ref: /schemas/leds/backlight/common.yaml# + +properties: + compatible: + const: ti,lm3533-backlight + + reg: + description: Control bank selection (0 = bank A, 1 = bank B). + maximum: 1 + + led-max-microamp: + description: maximum current in uA with a 800 uA step. + minimum: 5000 + maximum: 29800 + default: 5000 + + led-sources: + description: | + HVLED strings associated with this control bank: + 0 - HVLED1 + 1 - HVLED2 + minItems: 1 + maxItems: 2 + items: + maximum: 1 + + ti,pwm-config-mask: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Control Bank PWM Configuration Register mask that allows to configure + PWM input in Zones 0-4 + BIT(0) - PWM Input is enabled + BIT(1) - PWM Input is enabled in Zone 0 + BIT(2) - PWM Input is enabled in Zone 1 + BIT(3) - PWM Input is enabled in Zone 2 + BIT(4) - PWM Input is enabled in Zone 3 + BIT(5) - PWM Input is enabled in Zone 4 + + ti,linear-mapping-mode: + description: + Enable linear mapping mode. If disabled, then it will use exponential + mapping mode in which the ramp up/down appears to have a more uniform + transition to the human eye. + type: boolean + +required: + - compatible + - reg + +unevaluatedProperties: false + +# see ti,lm3533.yaml for an example diff --git a/Documentation/devicetree/bindings/leds/ti,lm3533-leds.yaml b/Documentation/devicetree/bindings/leds/ti,lm3533-leds.yaml new file mode 100644 index 000000000000..a582d7d2f955 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/ti,lm3533-leds.yaml @@ -0,0 +1,66 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/leds/ti,lm3533-leds.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TI LM3533 low voltage control banks for individual LEDs + +description: + This is part of the TI LM3533 MFD device. It represents four low voltage + control banks for individual LEDs provided by the TI LM3533. + +maintainers: + - Svyatoslav Ryhel <clamor95@gmail.com> + +allOf: + - $ref: /schemas/leds/common.yaml# + +properties: + compatible: + const: ti,lm3533-leds + + reg: + description: + Control bank selection (2 = bank C, 3 = bank D, 4 = bank E, 5 = bank F). + minimum: 2 + maximum: 5 + + led-max-microamp: + description: maximum current in uA with a 800 uA step. + minimum: 5000 + maximum: 29800 + default: 5000 + + led-sources: + description: | + LVLED associated with this control bank. May be more than 1 source per bank. + 0 - LVLED1 + 1 - LVLED2 + 2 - LVLED3 + 3 - LVLED4 + 4 - LVLED5 + minItems: 1 + maxItems: 5 + items: + maximum: 5 + + ti,pwm-config-mask: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Control Bank PWM Configuration Register mask that allows to configure + PWM input in Zones 0-4 + BIT(0) - PWM Input is enabled + BIT(1) - PWM Input is enabled in Zone 0 + BIT(2) - PWM Input is enabled in Zone 1 + BIT(3) - PWM Input is enabled in Zone 2 + BIT(4) - PWM Input is enabled in Zone 3 + BIT(5) - PWM Input is enabled in Zone 4 + +required: + - compatible + - reg + +unevaluatedProperties: false + +# see ti,lm3533.yaml for an example diff --git a/Documentation/devicetree/bindings/leds/ti,lm3533.yaml b/Documentation/devicetree/bindings/leds/ti,lm3533.yaml new file mode 100644 index 000000000000..2e200f172400 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/ti,lm3533.yaml @@ -0,0 +1,190 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/leds/ti,lm3533.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TI LM3533 Complete Lighting Power Solution + +description: > + The LM3533 is a complete power source for backlight, keypad, and indicator LEDs + in smartphone handsets. The high-voltage inductive boost converter provides the + power for two high voltage series LED strings for display backlight and four low + voltage control banks for individual LEDs. Additionally, LM3533 features an ALS + sensor support. + + https://www.ti.com/product/LM3533 + +maintainers: + - Svyatoslav Ryhel <clamor95@gmail.com> + +properties: + compatible: + const: ti,lm3533 + + reg: + maxItems: 1 + + enable-gpios: + description: GPIO connected to the HWEN pin. + maxItems: 1 + + vin-supply: + description: Supply connected to the IN line (2.7 V to 5.5 V). + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + ti,boost-ovp-microvolt: + description: boost OVP select (16V, 24V, 32V, 40V) + enum: [ 16000000, 24000000, 32000000, 40000000 ] + default: 16000000 + + ti,boost-freq-hz: + description: boost frequency select (500KHz or 1MHz) + enum: [ 500000, 1000000 ] + default: 500000 + + light-sensor: + type: object + additionalProperties: false + + properties: + compatible: + const: ti,lm3533-als + + interrupts: + maxItems: 1 + + ti,resistor-ohm: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Internal configuration resister value when ALS is in Analog Sensor + mode and PWM mode is disabled. + minimum: 1575 + maximum: 200000 + + ti,pwm-mode: + type: boolean + description: + Switch for mode in which ALS is running. If this property is set + then ALS is running in PWM mode, internal resistor value is set to + high-impedance (0) and ti,resistor-ohm property is ignored. + + required: + - compatible + + anyOf: + - required: + - ti,resistor-ohm + - required: + - ti,pwm-mode + +patternProperties: + "^backlight@[01]$": + $ref: /schemas/leds/backlight/ti,lm3533-backlight.yaml# + + "^led@[2-5]$": + $ref: /schemas/leds/ti,lm3533-leds.yaml# + +required: + - compatible + - reg + - light-sensor + - backlight@0 + - backlight@1 + - led@2 + - led@3 + - led@4 + - led@5 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + led-controller@36 { + compatible = "ti,lm3533"; + reg = <0x36>; + + enable-gpios = <&gpio 110 GPIO_ACTIVE_HIGH>; + vin-supply = <&vdd_3v3_bat>; + + ti,boost-ovp-microvolt = <24000000>; + ti,boost-freq-hz = <500000>; + + #address-cells = <1>; + #size-cells = <0>; + + backlight@0 { + compatible = "ti,lm3533-backlight"; + reg = <0>; + + default-brightness = <113>; + + led-max-microamp = <23400>; + led-sources = <0>; + }; + + backlight@1 { + compatible = "ti,lm3533-backlight"; + reg = <1>; + + default-brightness = <113>; + + led-max-microamp = <23400>; + led-sources = <1>; + }; + + led@2 { + compatible = "ti,lm3533-leds"; + reg = <2>; + + led-max-microamp = <23400>; + led-sources = <0>; + }; + + led@3 { + compatible = "ti,lm3533-leds"; + reg = <3>; + + led-max-microamp = <23400>; + led-sources = <1>; + }; + + led@4 { + compatible = "ti,lm3533-leds"; + reg = <4>; + + led-max-microamp = <23400>; + led-sources = <2>; + }; + + led@5 { + compatible = "ti,lm3533-leds"; + reg = <5>; + + led-max-microamp = <23400>; + led-sources = <3 4>; + }; + + light-sensor { + compatible = "ti,lm3533-als"; + + interrupt-parent = <&gpio>; + interrupts = <80 IRQ_TYPE_LEVEL_LOW>; + + ti,pwm-mode; + }; + }; + }; +... -- 2.51.0 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH v1 1/6] dt-bindings: leds: Document TI LM3533 LED controller 2026-05-17 7:43 ` [PATCH v1 1/6] dt-bindings: leds: Document TI LM3533 LED controller Svyatoslav Ryhel @ 2026-05-17 13:44 ` Jonathan Cameron 2026-05-17 14:26 ` Svyatoslav Ryhel 0 siblings, 1 reply; 18+ messages in thread From: Jonathan Cameron @ 2026-05-17 13:44 UTC (permalink / raw) To: Svyatoslav Ryhel Cc: Lee Jones, Daniel Thompson, Jingoo Han, Pavel Machek, Rob Herring, Krzysztof Kozlowski, Conor Dooley, David Lechner, Nuno Sá, Andy Shevchenko, Helge Deller, dri-devel, linux-leds, devicetree, linux-kernel, linux-iio, linux-fbdev On Sun, 17 May 2026 10:43:01 +0300 Svyatoslav Ryhel <clamor95@gmail.com> wrote: > Document the LM3533 - a complete power source for backlight, keypad and > indicator LEDs in smartphone handsets. The high-voltage inductive boost > converter provides the power for two series LED strings display backlight > and keypad functions. > > Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> Hi Svyatoslav, I focused on the ALS part.. A few comments. > +# see ti,lm3533.yaml for an example > diff --git a/Documentation/devicetree/bindings/leds/ti,lm3533.yaml b/Documentation/devicetree/bindings/leds/ti,lm3533.yaml > new file mode 100644 > index 000000000000..2e200f172400 > --- /dev/null > +++ b/Documentation/devicetree/bindings/leds/ti,lm3533.yaml > @@ -0,0 +1,190 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/leds/ti,lm3533.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: TI LM3533 Complete Lighting Power Solution > + > +description: > > + The LM3533 is a complete power source for backlight, keypad, and indicator LEDs > + in smartphone handsets. The high-voltage inductive boost converter provides the > + power for two high voltage series LED strings for display backlight and four low > + voltage control banks for individual LEDs. Additionally, LM3533 features an ALS > + sensor support. Mention it is an interface for an external ALS. > + light-sensor: > + type: object > + additionalProperties: false > + > + properties: > + compatible: > + const: ti,lm3533-als > + > + interrupts: > + maxItems: 1 > + > + ti,resistor-ohm: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: > + Internal configuration resister value when ALS is in Analog Sensor > + mode and PWM mode is disabled. Good to note why this is a firmware thing rather than a userspace controlled thing. I looked it up, it's because expectation is the input is a current from the external analog ALS and these are used to convert it to a voltage with target range. > + minimum: 1575 > + maximum: 200000 > + > + ti,pwm-mode: > + type: boolean > + description: > + Switch for mode in which ALS is running. If this property is set > + then ALS is running in PWM mode, internal resistor value is set to > + high-impedance (0) and ti,resistor-ohm property is ignored. I'd mention the ALS is an external device - so this is saying what interface thing thing connected is using. > + > + required: > + - compatible > + > + anyOf: > + - required: > + - ti,resistor-ohm > + - required: > + - ti,pwm-mode > + > +patternProperties: > + "^backlight@[01]$": > + $ref: /schemas/leds/backlight/ti,lm3533-backlight.yaml# > + > + "^led@[2-5]$": > + $ref: /schemas/leds/ti,lm3533-leds.yaml# > + > +required: > + - compatible > + - reg > + - light-sensor > + - backlight@0 > + - backlight@1 Similar for the led nodes. > + - led@2 > + - led@3 > + - led@4 > + - led@5 Curious - why are all the led nodes required? What if some aren't wired to anything? > + > +additionalProperties: false ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v1 1/6] dt-bindings: leds: Document TI LM3533 LED controller 2026-05-17 13:44 ` Jonathan Cameron @ 2026-05-17 14:26 ` Svyatoslav Ryhel 0 siblings, 0 replies; 18+ messages in thread From: Svyatoslav Ryhel @ 2026-05-17 14:26 UTC (permalink / raw) To: Jonathan Cameron Cc: Lee Jones, Daniel Thompson, Jingoo Han, Pavel Machek, Rob Herring, Krzysztof Kozlowski, Conor Dooley, David Lechner, Nuno Sá, Andy Shevchenko, Helge Deller, dri-devel, linux-leds, devicetree, linux-kernel, linux-iio, linux-fbdev нд, 17 трав. 2026 р. о 16:45 Jonathan Cameron <jic23@kernel.org> пише: > > On Sun, 17 May 2026 10:43:01 +0300 > Svyatoslav Ryhel <clamor95@gmail.com> wrote: > > > Document the LM3533 - a complete power source for backlight, keypad and > > indicator LEDs in smartphone handsets. The high-voltage inductive boost > > converter provides the power for two series LED strings display backlight > > and keypad functions. > > > > Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> > Hi Svyatoslav, > > I focused on the ALS part.. A few comments. > > > +# see ti,lm3533.yaml for an example > > diff --git a/Documentation/devicetree/bindings/leds/ti,lm3533.yaml b/Documentation/devicetree/bindings/leds/ti,lm3533.yaml > > new file mode 100644 > > index 000000000000..2e200f172400 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/leds/ti,lm3533.yaml > > @@ -0,0 +1,190 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/leds/ti,lm3533.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: TI LM3533 Complete Lighting Power Solution > > + > > +description: > > > + The LM3533 is a complete power source for backlight, keypad, and indicator LEDs > > + in smartphone handsets. The high-voltage inductive boost converter provides the > > + power for two high voltage series LED strings for display backlight and four low > > + voltage control banks for individual LEDs. Additionally, LM3533 features an ALS > > + sensor support. > Mention it is an interface for an external ALS. > Noted, thank you! > > + light-sensor: > > + type: object > > + additionalProperties: false > > + > > + properties: > > + compatible: > > + const: ti,lm3533-als > > + > > + interrupts: > > + maxItems: 1 > > + > > + ti,resistor-ohm: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + description: > > + Internal configuration resister value when ALS is in Analog Sensor > > + mode and PWM mode is disabled. > > Good to note why this is a firmware thing rather than a userspace controlled > thing. I looked it up, it's because expectation is the input is a current from > the external analog ALS and these are used to convert it to a voltage with target > range. > I will include your explanation. > > + minimum: 1575 > > + maximum: 200000 > > + > > + ti,pwm-mode: > > + type: boolean > > + description: > > + Switch for mode in which ALS is running. If this property is set > > + then ALS is running in PWM mode, internal resistor value is set to > > + high-impedance (0) and ti,resistor-ohm property is ignored. > I'd mention the ALS is an external device - so this is saying what interface thing > thing connected is using. > Noted > > + > > + required: > > + - compatible > > + > > + anyOf: > > + - required: > > + - ti,resistor-ohm > > + - required: > > + - ti,pwm-mode > > + > > +patternProperties: > > + "^backlight@[01]$": > > + $ref: /schemas/leds/backlight/ti,lm3533-backlight.yaml# > > + > > + "^led@[2-5]$": > > + $ref: /schemas/leds/ti,lm3533-leds.yaml# > > + > > +required: > > + - compatible > > + - reg > > + - light-sensor > > + - backlight@0 > > + - backlight@1 > > Similar for the led nodes. > > > + - led@2 > > + - led@3 > > + - led@4 > > + - led@5 > > Curious - why are all the led nodes required? What if some aren't wired to anything? > This is limitations of mfd devices. If it has subnodes, all subnodes must be present to reflect mfd composition. Unused nodes should be disabled. However, I have asked Lee if he is fine if I will program dynamic mfd composition based on the device tree. If he is fine, "required" props/nodes list will be reduced. > > + > > +additionalProperties: false > ^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v1 2/6] mfd: lm3533: Convert to use OF bindings 2026-05-17 7:43 [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support Svyatoslav Ryhel 2026-05-17 7:43 ` [PATCH v1 1/6] dt-bindings: leds: Document TI LM3533 LED controller Svyatoslav Ryhel @ 2026-05-17 7:43 ` Svyatoslav Ryhel 2026-05-17 7:55 ` Andy Shevchenko 2026-05-17 11:10 ` Svyatoslav Ryhel 2026-05-17 7:43 ` [PATCH v1 3/6] mfd: lm3533: Add support for VIN power supply Svyatoslav Ryhel ` (4 subsequent siblings) 6 siblings, 2 replies; 18+ messages in thread From: Svyatoslav Ryhel @ 2026-05-17 7:43 UTC (permalink / raw) To: Lee Jones, Daniel Thompson, Jingoo Han, Pavel Machek, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko, Helge Deller, Svyatoslav Ryhel Cc: dri-devel, linux-leds, devicetree, linux-kernel, linux-iio, linux-fbdev Since there are no users of this driver via platform data, remove the platform data support and switch to using Device Tree bindings. Additionally, optimize functions used only by platform data. Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> --- drivers/iio/light/lm3533-als.c | 123 +++++-------- drivers/leds/leds-lm3533.c | 60 ++++--- drivers/mfd/lm3533-core.c | 257 +++++++++------------------- drivers/video/backlight/lm3533_bl.c | 52 ++++-- include/linux/mfd/lm3533.h | 51 +----- 5 files changed, 202 insertions(+), 341 deletions(-) diff --git a/drivers/iio/light/lm3533-als.c b/drivers/iio/light/lm3533-als.c index 99f0b903018c..853abb96e13f 100644 --- a/drivers/iio/light/lm3533-als.c +++ b/drivers/iio/light/lm3533-als.c @@ -16,15 +16,18 @@ #include <linux/module.h> #include <linux/mutex.h> #include <linux/mfd/core.h> +#include <linux/mod_devicetable.h> #include <linux/platform_device.h> +#include <linux/property.h> #include <linux/slab.h> #include <linux/uaccess.h> +#include <linux/units.h> #include <linux/mfd/lm3533.h> -#define LM3533_ALS_RESISTOR_MIN 1 -#define LM3533_ALS_RESISTOR_MAX 127 +#define LM3533_ALS_RESISTOR_MIN 1575 +#define LM3533_ALS_RESISTOR_MAX 200000 #define LM3533_ALS_CHANNEL_CURRENT_MAX 2 #define LM3533_ALS_THRESH_MAX 3 #define LM3533_ALS_ZONE_MAX 4 @@ -56,6 +59,9 @@ struct lm3533_als { atomic_t zone; struct mutex thresh_mutex; + + bool pwm_mode; + u32 r_select; }; @@ -714,64 +720,6 @@ static const struct attribute_group lm3533_als_attribute_group = { .attrs = lm3533_als_attributes }; -static int lm3533_als_set_input_mode(struct lm3533_als *als, bool pwm_mode) -{ - u8 mask = LM3533_ALS_INPUT_MODE_MASK; - u8 val; - int ret; - - if (pwm_mode) - val = mask; /* pwm input */ - else - val = 0; /* analog input */ - - ret = lm3533_update(als->lm3533, LM3533_REG_ALS_CONF, val, mask); - if (ret) { - dev_err(&als->pdev->dev, "failed to set input mode %d\n", - pwm_mode); - return ret; - } - - return 0; -} - -static int lm3533_als_set_resistor(struct lm3533_als *als, u8 val) -{ - int ret; - - if (val < LM3533_ALS_RESISTOR_MIN || val > LM3533_ALS_RESISTOR_MAX) { - dev_err(&als->pdev->dev, "invalid resistor value\n"); - return -EINVAL; - } - - ret = lm3533_write(als->lm3533, LM3533_REG_ALS_RESISTOR_SELECT, val); - if (ret) { - dev_err(&als->pdev->dev, "failed to set resistor\n"); - return ret; - } - - return 0; -} - -static int lm3533_als_setup(struct lm3533_als *als, - const struct lm3533_als_platform_data *pdata) -{ - int ret; - - ret = lm3533_als_set_input_mode(als, pdata->pwm_mode); - if (ret) - return ret; - - /* ALS input is always high impedance in PWM-mode. */ - if (!pdata->pwm_mode) { - ret = lm3533_als_set_resistor(als, pdata->r_select); - if (ret) - return ret; - } - - return 0; -} - static int lm3533_als_setup_irq(struct lm3533_als *als, void *dev) { u8 mask = LM3533_ALS_INT_ENABLE_MASK; @@ -784,7 +732,8 @@ static int lm3533_als_setup_irq(struct lm3533_als *als, void *dev) return ret; } - ret = request_threaded_irq(als->irq, NULL, lm3533_als_isr, + ret = devm_request_threaded_irq(&als->pdev->dev, als->irq, NULL, + lm3533_als_isr, IRQF_TRIGGER_LOW | IRQF_ONESHOT, dev_name(&als->pdev->dev), dev); if (ret) { @@ -828,7 +777,6 @@ static const struct iio_info lm3533_als_info = { static int lm3533_als_probe(struct platform_device *pdev) { - const struct lm3533_als_platform_data *pdata; struct lm3533 *lm3533; struct lm3533_als *als; struct iio_dev *indio_dev; @@ -838,12 +786,6 @@ static int lm3533_als_probe(struct platform_device *pdev) if (!lm3533) return -EINVAL; - pdata = dev_get_platdata(&pdev->dev); - if (!pdata) { - dev_err(&pdev->dev, "no platform data\n"); - return -EINVAL; - } - indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*als)); if (!indio_dev) return -ENOMEM; @@ -852,31 +794,52 @@ static int lm3533_als_probe(struct platform_device *pdev) indio_dev->channels = lm3533_als_channels; indio_dev->num_channels = ARRAY_SIZE(lm3533_als_channels); indio_dev->name = dev_name(&pdev->dev); - iio_device_set_parent(indio_dev, pdev->dev.parent); indio_dev->modes = INDIO_DIRECT_MODE; als = iio_priv(indio_dev); als->lm3533 = lm3533; als->pdev = pdev; - als->irq = lm3533->irq; + als->irq = platform_get_irq_optional(pdev, 0); atomic_set(&als->zone, 0); mutex_init(&als->thresh_mutex); platform_set_drvdata(pdev, indio_dev); - if (als->irq) { + if (als->irq > 0) { ret = lm3533_als_setup_irq(als, indio_dev); if (ret) return ret; } - ret = lm3533_als_setup(als, pdata); + device_property_read_u32(&pdev->dev, "ti,resistor-value-ohm", + &als->r_select); + + als->r_select = clamp(als->r_select, LM3533_ALS_RESISTOR_MIN, + LM3533_ALS_RESISTOR_MAX); + als->r_select = DIV_ROUND_UP(2 * MICRO, 10 * als->r_select); + + als->pwm_mode = device_property_read_bool(&pdev->dev, "ti,pwm-mode"); + + ret = lm3533_update(lm3533, LM3533_REG_ALS_CONF, als->pwm_mode ? + LM3533_ALS_INPUT_MODE_MASK : 0, + LM3533_ALS_INPUT_MODE_MASK); if (ret) - goto err_free_irq; + return dev_err_probe(&pdev->dev, ret, + "failed to set input mode %d\n", + als->pwm_mode); + + /* ALS input is always high impedance in PWM-mode. */ + if (!als->pwm_mode) { + ret = lm3533_write(lm3533, LM3533_REG_ALS_RESISTOR_SELECT, + (u8)als->r_select); + if (ret) + return dev_err_probe(&pdev->dev, ret, + "failed to set resistor\n"); + } ret = lm3533_als_enable(als); if (ret) - goto err_free_irq; + return ret; ret = iio_device_register(indio_dev); if (ret) { @@ -888,9 +851,6 @@ static int lm3533_als_probe(struct platform_device *pdev) err_disable: lm3533_als_disable(als); -err_free_irq: - if (als->irq) - free_irq(als->irq, indio_dev); return ret; } @@ -903,13 +863,18 @@ static void lm3533_als_remove(struct platform_device *pdev) lm3533_als_set_int_mode(indio_dev, false); iio_device_unregister(indio_dev); lm3533_als_disable(als); - if (als->irq) - free_irq(als->irq, indio_dev); } +static const struct of_device_id lm3533_als_match_table[] = { + { .compatible = "ti,lm3533-als" }, + { } +}; +MODULE_DEVICE_TABLE(of, lm3533_als_match_table); + static struct platform_driver lm3533_als_driver = { .driver = { .name = "lm3533-als", + .of_match_table = lm3533_als_match_table, }, .probe = lm3533_als_probe, .remove = lm3533_als_remove, diff --git a/drivers/leds/leds-lm3533.c b/drivers/leds/leds-lm3533.c index 45795f2a1042..f6345bc1f443 100644 --- a/drivers/leds/leds-lm3533.c +++ b/drivers/leds/leds-lm3533.c @@ -10,8 +10,10 @@ #include <linux/module.h> #include <linux/leds.h> #include <linux/mfd/core.h> +#include <linux/mod_devicetable.h> #include <linux/mutex.h> #include <linux/platform_device.h> +#include <linux/property.h> #include <linux/slab.h> #include <linux/mfd/lm3533.h> @@ -48,6 +50,9 @@ struct lm3533_led { struct mutex mutex; unsigned long flags; + + u32 max_current; + u32 pwm; }; @@ -632,22 +637,20 @@ static const struct attribute_group *lm3533_led_attribute_groups[] = { NULL }; -static int lm3533_led_setup(struct lm3533_led *led, - struct lm3533_led_platform_data *pdata) +static int lm3533_led_setup(struct lm3533_led *led) { int ret; - ret = lm3533_ctrlbank_set_max_current(&led->cb, pdata->max_current); + ret = lm3533_ctrlbank_set_max_current(&led->cb, led->max_current); if (ret) return ret; - return lm3533_ctrlbank_set_pwm(&led->cb, pdata->pwm); + return lm3533_ctrlbank_set_pwm(&led->cb, led->pwm); } static int lm3533_led_probe(struct platform_device *pdev) { struct lm3533 *lm3533; - struct lm3533_led_platform_data *pdata; struct lm3533_led *led; int ret; @@ -657,30 +660,30 @@ static int lm3533_led_probe(struct platform_device *pdev) if (!lm3533) return -EINVAL; - pdata = dev_get_platdata(&pdev->dev); - if (!pdata) { - dev_err(&pdev->dev, "no platform data\n"); - return -EINVAL; - } - - if (pdev->id < 0 || pdev->id >= LM3533_LVCTRLBANK_COUNT) { - dev_err(&pdev->dev, "illegal LED id %d\n", pdev->id); - return -EINVAL; - } + if (pdev->id < LM3533_LVCTRLBANK_MIN || pdev->id > LM3533_LVCTRLBANK_MAX) + return dev_err_probe(&pdev->dev, -EINVAL, + "illegal LED id %d\n", pdev->id); led = devm_kzalloc(&pdev->dev, sizeof(*led), GFP_KERNEL); if (!led) return -ENOMEM; led->lm3533 = lm3533; - led->cdev.name = pdata->name; - led->cdev.default_trigger = pdata->default_trigger; led->cdev.brightness_set_blocking = lm3533_led_set; led->cdev.brightness_get = lm3533_led_get; led->cdev.blink_set = lm3533_led_blink_set; led->cdev.brightness = LED_OFF; led->cdev.groups = lm3533_led_attribute_groups; - led->id = pdev->id; + led->id = pdev->id - LM3533_LVCTRLBANK_MIN; + + led->cdev.name = devm_kasprintf(&pdev->dev, GFP_KERNEL, "%s-%d", + pdev->name, led->id); + if (!led->cdev.name) + return -ENOMEM; + + led->cdev.default_trigger = "none"; + device_property_read_string(&pdev->dev, "linux,default-trigger", + &led->cdev.default_trigger); mutex_init(&led->mutex); @@ -694,15 +697,23 @@ static int lm3533_led_probe(struct platform_device *pdev) platform_set_drvdata(pdev, led); - ret = led_classdev_register(pdev->dev.parent, &led->cdev); + ret = led_classdev_register(&pdev->dev, &led->cdev); if (ret) { - dev_err(&pdev->dev, "failed to register LED %d\n", pdev->id); + dev_err(&pdev->dev, "failed to register LED %d\n", led->id); return ret; } led->cb.dev = led->cdev.dev; - ret = lm3533_led_setup(led, pdata); + device_property_read_u32(&pdev->dev, "led-max-microamp", + &led->max_current); + led->max_current = clamp(led->max_current, LM3533_LED_MAX_CURRENT_MIN, + LM3533_LED_MAX_CURRENT_MAX); + + led->pwm = 0; + device_property_read_u32(&pdev->dev, "ti,pwm-config-mask", &led->pwm); + + ret = lm3533_led_setup(led); if (ret) goto err_deregister; @@ -739,9 +750,16 @@ static void lm3533_led_shutdown(struct platform_device *pdev) lm3533_led_set(&led->cdev, LED_OFF); /* disable blink */ } +static const struct of_device_id lm3533_led_match_table[] = { + { .compatible = "ti,lm3533-leds" }, + { } +}; +MODULE_DEVICE_TABLE(of, lm3533_led_match_table); + static struct platform_driver lm3533_led_driver = { .driver = { .name = "lm3533-leds", + .of_match_table = lm3533_led_match_table, }, .probe = lm3533_led_probe, .remove = lm3533_led_remove, diff --git a/drivers/mfd/lm3533-core.c b/drivers/mfd/lm3533-core.c index 0a2409d00b2e..83ebd780f39d 100644 --- a/drivers/mfd/lm3533-core.c +++ b/drivers/mfd/lm3533-core.c @@ -14,19 +14,26 @@ #include <linux/gpio/consumer.h> #include <linux/i2c.h> #include <linux/mfd/core.h> +#include <linux/mod_devicetable.h> +#include <linux/property.h> #include <linux/regmap.h> #include <linux/seq_file.h> #include <linux/slab.h> #include <linux/uaccess.h> +#include <linux/units.h> #include <linux/mfd/lm3533.h> #define LM3533_BOOST_OVP_MASK 0x06 #define LM3533_BOOST_OVP_SHIFT 1 +#define LM3533_BOOST_OVP_MIN 16000000 +#define LM3533_BOOST_OVP_MAX 40000000 #define LM3533_BOOST_FREQ_MASK 0x01 #define LM3533_BOOST_FREQ_SHIFT 0 +#define LM3533_BOOST_FREQ_MIN 500000 +#define LM3533_BOOST_FREQ_MAX 1000000 #define LM3533_BL_ID_MASK 1 #define LM3533_LED_ID_MASK 3 @@ -42,42 +49,14 @@ #define LM3533_REG_MAX 0xb2 - -static struct mfd_cell lm3533_als_devs[] = { - { - .name = "lm3533-als", - .id = -1, - }, -}; - -static struct mfd_cell lm3533_bl_devs[] = { - { - .name = "lm3533-backlight", - .id = 0, - }, - { - .name = "lm3533-backlight", - .id = 1, - }, -}; - -static struct mfd_cell lm3533_led_devs[] = { - { - .name = "lm3533-leds", - .id = 0, - }, - { - .name = "lm3533-leds", - .id = 1, - }, - { - .name = "lm3533-leds", - .id = 2, - }, - { - .name = "lm3533-leds", - .id = 3, - }, +static struct mfd_cell lm3533_child_devices[] = { + MFD_CELL_OF("lm3533-als", NULL, NULL, 0, 0, "ti,lm3533-als"), + MFD_CELL_OF_REG("lm3533-backlight", NULL, NULL, 0, 0, "ti,lm3533-backlight", 0), + MFD_CELL_OF_REG("lm3533-backlight", NULL, NULL, 0, 1, "ti,lm3533-backlight", 1), + MFD_CELL_OF_REG("lm3533-leds", NULL, NULL, 0, 0, "ti,lm3533-leds", 2), + MFD_CELL_OF_REG("lm3533-leds", NULL, NULL, 0, 1, "ti,lm3533-leds", 3), + MFD_CELL_OF_REG("lm3533-leds", NULL, NULL, 0, 2, "ti,lm3533-leds", 4), + MFD_CELL_OF_REG("lm3533-leds", NULL, NULL, 0, 3, "ti,lm3533-leds", 5), }; int lm3533_read(struct lm3533 *lm3533, u8 reg, u8 *val) @@ -132,35 +111,6 @@ int lm3533_update(struct lm3533 *lm3533, u8 reg, u8 val, u8 mask) } EXPORT_SYMBOL_GPL(lm3533_update); -static int lm3533_set_boost_freq(struct lm3533 *lm3533, - enum lm3533_boost_freq freq) -{ - int ret; - - ret = lm3533_update(lm3533, LM3533_REG_BOOST_PWM, - freq << LM3533_BOOST_FREQ_SHIFT, - LM3533_BOOST_FREQ_MASK); - if (ret) - dev_err(lm3533->dev, "failed to set boost frequency\n"); - - return ret; -} - - -static int lm3533_set_boost_ovp(struct lm3533 *lm3533, - enum lm3533_boost_ovp ovp) -{ - int ret; - - ret = lm3533_update(lm3533, LM3533_REG_BOOST_PWM, - ovp << LM3533_BOOST_OVP_SHIFT, - LM3533_BOOST_OVP_MASK); - if (ret) - dev_err(lm3533->dev, "failed to set boost ovp\n"); - - return ret; -} - /* * HVLED output config -- output hvled controlled by backlight bl */ @@ -376,136 +326,45 @@ static struct attribute_group lm3533_attribute_group = { .attrs = lm3533_attributes }; -static int lm3533_device_als_init(struct lm3533 *lm3533) +static int lm3533_device_init(struct lm3533 *lm3533) { - struct lm3533_platform_data *pdata = dev_get_platdata(lm3533->dev); + struct device *dev = lm3533->dev; int ret; - if (!pdata->als) - return 0; - - lm3533_als_devs[0].platform_data = pdata->als; - lm3533_als_devs[0].pdata_size = sizeof(*pdata->als); + lm3533_enable(lm3533); - ret = mfd_add_devices(lm3533->dev, 0, lm3533_als_devs, 1, NULL, - 0, NULL); + ret = lm3533_update(lm3533, LM3533_REG_BOOST_PWM, + lm3533->boost_freq << LM3533_BOOST_FREQ_SHIFT, + LM3533_BOOST_FREQ_MASK); if (ret) { - dev_err(lm3533->dev, "failed to add ALS device\n"); - return ret; - } - - lm3533->have_als = 1; - - return 0; -} - -static int lm3533_device_bl_init(struct lm3533 *lm3533) -{ - struct lm3533_platform_data *pdata = dev_get_platdata(lm3533->dev); - int i; - int ret; - - if (!pdata->backlights || pdata->num_backlights == 0) - return 0; - - if (pdata->num_backlights > ARRAY_SIZE(lm3533_bl_devs)) - pdata->num_backlights = ARRAY_SIZE(lm3533_bl_devs); - - for (i = 0; i < pdata->num_backlights; ++i) { - lm3533_bl_devs[i].platform_data = &pdata->backlights[i]; - lm3533_bl_devs[i].pdata_size = sizeof(pdata->backlights[i]); + dev_err(dev, "failed to set boost frequency\n"); + goto err_disable; } - ret = mfd_add_devices(lm3533->dev, 0, lm3533_bl_devs, - pdata->num_backlights, NULL, 0, NULL); + ret = lm3533_update(lm3533, LM3533_REG_BOOST_PWM, + lm3533->boost_ovp << LM3533_BOOST_OVP_SHIFT, + LM3533_BOOST_OVP_MASK); if (ret) { - dev_err(lm3533->dev, "failed to add backlight devices\n"); - return ret; - } - - lm3533->have_backlights = 1; - - return 0; -} - -static int lm3533_device_led_init(struct lm3533 *lm3533) -{ - struct lm3533_platform_data *pdata = dev_get_platdata(lm3533->dev); - int i; - int ret; - - if (!pdata->leds || pdata->num_leds == 0) - return 0; - - if (pdata->num_leds > ARRAY_SIZE(lm3533_led_devs)) - pdata->num_leds = ARRAY_SIZE(lm3533_led_devs); - - for (i = 0; i < pdata->num_leds; ++i) { - lm3533_led_devs[i].platform_data = &pdata->leds[i]; - lm3533_led_devs[i].pdata_size = sizeof(pdata->leds[i]); + dev_err(dev, "failed to set boost ovp\n"); + goto err_disable; } - ret = mfd_add_devices(lm3533->dev, 0, lm3533_led_devs, - pdata->num_leds, NULL, 0, NULL); + ret = devm_mfd_add_devices(dev, 0, lm3533_child_devices, + ARRAY_SIZE(lm3533_child_devices), + NULL, 0, NULL); if (ret) { - dev_err(lm3533->dev, "failed to add LED devices\n"); - return ret; - } - - lm3533->have_leds = 1; - - return 0; -} - -static int lm3533_device_setup(struct lm3533 *lm3533, - struct lm3533_platform_data *pdata) -{ - int ret; - - ret = lm3533_set_boost_freq(lm3533, pdata->boost_freq); - if (ret) - return ret; - - return lm3533_set_boost_ovp(lm3533, pdata->boost_ovp); -} - -static int lm3533_device_init(struct lm3533 *lm3533) -{ - struct lm3533_platform_data *pdata = dev_get_platdata(lm3533->dev); - int ret; - - dev_dbg(lm3533->dev, "%s\n", __func__); - - if (!pdata) { - dev_err(lm3533->dev, "no platform data\n"); - return -EINVAL; + dev_err(dev, "failed to add MFD devices: %d\n", ret); + goto err_disable; } - lm3533->hwen = devm_gpiod_get(lm3533->dev, NULL, GPIOD_OUT_LOW); - if (IS_ERR(lm3533->hwen)) - return dev_err_probe(lm3533->dev, PTR_ERR(lm3533->hwen), "failed to request HWEN GPIO\n"); - gpiod_set_consumer_name(lm3533->hwen, "lm3533-hwen"); - - lm3533_enable(lm3533); - - ret = lm3533_device_setup(lm3533, pdata); - if (ret) + ret = sysfs_create_group(&dev->kobj, &lm3533_attribute_group); + if (ret) { + dev_err(dev, "failed to create sysfs attributes\n"); goto err_disable; - - lm3533_device_als_init(lm3533); - lm3533_device_bl_init(lm3533); - lm3533_device_led_init(lm3533); - - ret = sysfs_create_group(&lm3533->dev->kobj, &lm3533_attribute_group); - if (ret < 0) { - dev_err(lm3533->dev, "failed to create sysfs attributes\n"); - goto err_unregister; } return 0; -err_unregister: - mfd_remove_devices(lm3533->dev); err_disable: lm3533_disable(lm3533); @@ -517,8 +376,6 @@ static void lm3533_device_exit(struct lm3533 *lm3533) dev_dbg(lm3533->dev, "%s\n", __func__); sysfs_remove_group(&lm3533->dev->kobj, &lm3533_attribute_group); - - mfd_remove_devices(lm3533->dev); lm3533_disable(lm3533); } @@ -589,7 +446,40 @@ static int lm3533_i2c_probe(struct i2c_client *i2c) return PTR_ERR(lm3533->regmap); lm3533->dev = &i2c->dev; - lm3533->irq = i2c->irq; + + lm3533->hwen = devm_gpiod_get_optional(lm3533->dev, "enable", + GPIOD_OUT_LOW); + if (IS_ERR(lm3533->hwen)) + return dev_err_probe(lm3533->dev, PTR_ERR(lm3533->hwen), + "failed to get HWEN GPIO\n"); + + device_property_read_u32(lm3533->dev, "ti,boost-ovp-microvolt", + &lm3533->boost_ovp); + + lm3533->boost_ovp = clamp(lm3533->boost_ovp, LM3533_BOOST_OVP_MIN, + LM3533_BOOST_OVP_MAX); + lm3533->boost_ovp = lm3533->boost_ovp / (8 * MICRO) - 2; + + device_property_read_u32(lm3533->dev, "ti,boost-freq-hz", + &lm3533->boost_freq); + + lm3533->boost_freq = clamp(lm3533->boost_freq, LM3533_BOOST_FREQ_MIN, + LM3533_BOOST_FREQ_MAX); + lm3533->boost_freq = lm3533->boost_freq / (500 * KILO) - 1; + + device_for_each_child_node_scoped(lm3533->dev, child) { + if (!fwnode_device_is_available(child)) + continue; + + if (fwnode_device_is_compatible(child, "ti,lm3533-als")) + lm3533->have_als = true; + + if (fwnode_device_is_compatible(child, "ti,lm3533-backlight")) + lm3533->have_backlights = true; + + if (fwnode_device_is_compatible(child, "ti,lm3533-leds")) + lm3533->have_leds = true; + } return lm3533_device_init(lm3533); } @@ -603,6 +493,12 @@ static void lm3533_i2c_remove(struct i2c_client *i2c) lm3533_device_exit(lm3533); } +static const struct of_device_id lm3533_match_table[] = { + { .compatible = "ti,lm3533" }, + { } +}; +MODULE_DEVICE_TABLE(of, lm3533_match_table); + static const struct i2c_device_id lm3533_i2c_ids[] = { { "lm3533" }, { } @@ -612,6 +508,7 @@ MODULE_DEVICE_TABLE(i2c, lm3533_i2c_ids); static struct i2c_driver lm3533_i2c_driver = { .driver = { .name = "lm3533", + .of_match_table = lm3533_match_table, }, .id_table = lm3533_i2c_ids, .probe = lm3533_i2c_probe, diff --git a/drivers/video/backlight/lm3533_bl.c b/drivers/video/backlight/lm3533_bl.c index babfd3ceec86..42da652df58d 100644 --- a/drivers/video/backlight/lm3533_bl.c +++ b/drivers/video/backlight/lm3533_bl.c @@ -9,7 +9,9 @@ #include <linux/module.h> #include <linux/init.h> +#include <linux/mod_devicetable.h> #include <linux/platform_device.h> +#include <linux/property.h> #include <linux/backlight.h> #include <linux/slab.h> @@ -27,6 +29,9 @@ struct lm3533_bl { struct lm3533_ctrlbank cb; struct backlight_device *bd; int id; + + u32 max_current; + u32 pwm; }; @@ -246,25 +251,24 @@ static struct attribute_group lm3533_bl_attribute_group = { .attrs = lm3533_bl_attributes }; -static int lm3533_bl_setup(struct lm3533_bl *bl, - struct lm3533_bl_platform_data *pdata) +static int lm3533_bl_setup(struct lm3533_bl *bl) { int ret; - ret = lm3533_ctrlbank_set_max_current(&bl->cb, pdata->max_current); + ret = lm3533_ctrlbank_set_max_current(&bl->cb, bl->max_current); if (ret) return ret; - return lm3533_ctrlbank_set_pwm(&bl->cb, pdata->pwm); + return lm3533_ctrlbank_set_pwm(&bl->cb, bl->pwm); } static int lm3533_bl_probe(struct platform_device *pdev) { struct lm3533 *lm3533; - struct lm3533_bl_platform_data *pdata; struct lm3533_bl *bl; struct backlight_device *bd; struct backlight_properties props; + char *name = NULL; int ret; dev_dbg(&pdev->dev, "%s\n", __func__); @@ -273,12 +277,6 @@ static int lm3533_bl_probe(struct platform_device *pdev) if (!lm3533) return -EINVAL; - pdata = dev_get_platdata(&pdev->dev); - if (!pdata) { - dev_err(&pdev->dev, "no platform data\n"); - return -EINVAL; - } - if (pdev->id < 0 || pdev->id >= LM3533_HVCTRLBANK_COUNT) { dev_err(&pdev->dev, "illegal backlight id %d\n", pdev->id); return -EINVAL; @@ -295,13 +293,20 @@ static int lm3533_bl_probe(struct platform_device *pdev) bl->cb.id = lm3533_bl_get_ctrlbank_id(bl); bl->cb.dev = NULL; /* until registered */ + name = devm_kasprintf(&pdev->dev, GFP_KERNEL, "%s-%d", + pdev->name, pdev->id); + if (!name) + return -ENOMEM; + memset(&props, 0, sizeof(props)); props.type = BACKLIGHT_RAW; props.max_brightness = LM3533_BL_MAX_BRIGHTNESS; - props.brightness = pdata->default_brightness; - bd = devm_backlight_device_register(&pdev->dev, pdata->name, - pdev->dev.parent, bl, &lm3533_bl_ops, - &props); + props.brightness = LM3533_BL_MAX_BRIGHTNESS; + device_property_read_u32(&pdev->dev, "default-brightness", + &props.brightness); + + bd = devm_backlight_device_register(&pdev->dev, name, &pdev->dev, + bl, &lm3533_bl_ops, &props); if (IS_ERR(bd)) { dev_err(&pdev->dev, "failed to register backlight device\n"); return PTR_ERR(bd); @@ -320,7 +325,15 @@ static int lm3533_bl_probe(struct platform_device *pdev) backlight_update_status(bd); - ret = lm3533_bl_setup(bl, pdata); + device_property_read_u32(&pdev->dev, "led-max-microamp", + &bl->max_current); + bl->max_current = clamp(bl->max_current, LM3533_LED_MAX_CURRENT_MIN, + LM3533_LED_MAX_CURRENT_MAX); + + bl->pwm = 0; + device_property_read_u32(&pdev->dev, "ti,pwm-config-mask", &bl->pwm); + + ret = lm3533_bl_setup(bl); if (ret) goto err_sysfs_remove; @@ -381,10 +394,17 @@ static void lm3533_bl_shutdown(struct platform_device *pdev) lm3533_ctrlbank_disable(&bl->cb); } +static const struct of_device_id lm3533_bl_match_table[] = { + { .compatible = "ti,lm3533-backlight" }, + { } +}; +MODULE_DEVICE_TABLE(of, lm3533_bl_match_table); + static struct platform_driver lm3533_bl_driver = { .driver = { .name = "lm3533-backlight", .pm = &lm3533_bl_pm_ops, + .of_match_table = lm3533_bl_match_table, }, .probe = lm3533_bl_probe, .remove = lm3533_bl_remove, diff --git a/include/linux/mfd/lm3533.h b/include/linux/mfd/lm3533.h index 69059a7a2ce5..3aa962d4c747 100644 --- a/include/linux/mfd/lm3533.h +++ b/include/linux/mfd/lm3533.h @@ -15,6 +15,9 @@ #define LM3533_ATTR_RW(_name) \ DEVICE_ATTR(_name, S_IRUGO | S_IWUSR , show_##_name, store_##_name) +#define LM3533_LED_MAX_CURRENT_MIN 5000 +#define LM3533_LED_MAX_CURRENT_MAX 29800 + struct device; struct gpio_desc; struct regmap; @@ -25,7 +28,9 @@ struct lm3533 { struct regmap *regmap; struct gpio_desc *hwen; - int irq; + + u32 boost_ovp; + u32 boost_freq; unsigned have_als:1; unsigned have_backlights:1; @@ -38,50 +43,6 @@ struct lm3533_ctrlbank { int id; }; -struct lm3533_als_platform_data { - unsigned pwm_mode:1; /* PWM input mode (default analog) */ - u8 r_select; /* 1 - 127 (ignored in PWM-mode) */ -}; - -struct lm3533_bl_platform_data { - char *name; - u16 max_current; /* 5000 - 29800 uA (800 uA step) */ - u8 default_brightness; /* 0 - 255 */ - u8 pwm; /* 0 - 0x3f */ -}; - -struct lm3533_led_platform_data { - char *name; - const char *default_trigger; - u16 max_current; /* 5000 - 29800 uA (800 uA step) */ - u8 pwm; /* 0 - 0x3f */ -}; - -enum lm3533_boost_freq { - LM3533_BOOST_FREQ_500KHZ, - LM3533_BOOST_FREQ_1000KHZ, -}; - -enum lm3533_boost_ovp { - LM3533_BOOST_OVP_16V, - LM3533_BOOST_OVP_24V, - LM3533_BOOST_OVP_32V, - LM3533_BOOST_OVP_40V, -}; - -struct lm3533_platform_data { - enum lm3533_boost_ovp boost_ovp; - enum lm3533_boost_freq boost_freq; - - struct lm3533_als_platform_data *als; - - struct lm3533_bl_platform_data *backlights; - int num_backlights; - - struct lm3533_led_platform_data *leds; - int num_leds; -}; - extern int lm3533_ctrlbank_enable(struct lm3533_ctrlbank *cb); extern int lm3533_ctrlbank_disable(struct lm3533_ctrlbank *cb); -- 2.51.0 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH v1 2/6] mfd: lm3533: Convert to use OF bindings 2026-05-17 7:43 ` [PATCH v1 2/6] mfd: lm3533: Convert to use OF bindings Svyatoslav Ryhel @ 2026-05-17 7:55 ` Andy Shevchenko 2026-05-17 10:11 ` Svyatoslav Ryhel 2026-05-17 11:10 ` Svyatoslav Ryhel 1 sibling, 1 reply; 18+ messages in thread From: Andy Shevchenko @ 2026-05-17 7:55 UTC (permalink / raw) To: Svyatoslav Ryhel Cc: Lee Jones, Daniel Thompson, Jingoo Han, Pavel Machek, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko, Helge Deller, dri-devel, linux-leds, devicetree, linux-kernel, linux-iio, linux-fbdev On Sun, May 17, 2026 at 10:43:02AM +0300, Svyatoslav Ryhel wrote: > Since there are no users of this driver via platform data, remove the > platform data support and switch to using Device Tree bindings. > Additionally, optimize functions used only by platform data. This is a mixture of at least (!) three patches: - devm conversion - the change of some constants - the rest -- With Best Regards, Andy Shevchenko ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v1 2/6] mfd: lm3533: Convert to use OF bindings 2026-05-17 7:55 ` Andy Shevchenko @ 2026-05-17 10:11 ` Svyatoslav Ryhel 0 siblings, 0 replies; 18+ messages in thread From: Svyatoslav Ryhel @ 2026-05-17 10:11 UTC (permalink / raw) To: Andy Shevchenko Cc: Lee Jones, Daniel Thompson, Jingoo Han, Pavel Machek, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko, Helge Deller, dri-devel, linux-leds, devicetree, linux-kernel, linux-iio, linux-fbdev нд, 17 трав. 2026 р. о 10:55 Andy Shevchenko <andriy.shevchenko@intel.com> пише: > > On Sun, May 17, 2026 at 10:43:02AM +0300, Svyatoslav Ryhel wrote: > > Since there are no users of this driver via platform data, remove the > > platform data support and switch to using Device Tree bindings. > > Additionally, optimize functions used only by platform data. > > This is a mixture of at least (!) three patches: Maybe you can make a list of how to split it then. I have tried to make it complete and remain readable. I am open to your suggestions. > - devm conversion This will be dropped. > - the change of some constants If you mean LM3533_ALS_RESISTOR_MIN and LM3533_ALS_RESISTOR_MAX they are used explicitly in r_select value. Previously it was passed via pdata as register value and now it is obtained from the device tree as resistance in Ohms and register value is actually calculated. Naturally ALS_RESISTOR boundaries changed. > - the rest > > -- > With Best Regards, > Andy Shevchenko > > ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v1 2/6] mfd: lm3533: Convert to use OF bindings 2026-05-17 7:43 ` [PATCH v1 2/6] mfd: lm3533: Convert to use OF bindings Svyatoslav Ryhel 2026-05-17 7:55 ` Andy Shevchenko @ 2026-05-17 11:10 ` Svyatoslav Ryhel 1 sibling, 0 replies; 18+ messages in thread From: Svyatoslav Ryhel @ 2026-05-17 11:10 UTC (permalink / raw) To: Lee Jones Cc: Daniel Thompson, Jingoo Han, Rob Herring, Pavel Machek, Krzysztof Kozlowski, Conor Dooley, David Lechner, Jonathan Cameron, Nuno Sá, Helge Deller, dri-devel, linux-leds, devicetree, linux-kernel, linux-iio, linux-fbdev, Svyatoslav Ryhel, Andy Shevchenko нд, 17 трав. 2026 р. о 10:43 Svyatoslav Ryhel <clamor95@gmail.com> пише: > > Since there are no users of this driver via platform data, remove the > platform data support and switch to using Device Tree bindings. > Additionally, optimize functions used only by platform data. > > Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> > --- > drivers/iio/light/lm3533-als.c | 123 +++++-------- > drivers/leds/leds-lm3533.c | 60 ++++--- > drivers/mfd/lm3533-core.c | 257 +++++++++------------------- > drivers/video/backlight/lm3533_bl.c | 52 ++++-- > include/linux/mfd/lm3533.h | 51 +----- > 5 files changed, 202 insertions(+), 341 deletions(-) > > diff --git a/drivers/iio/light/lm3533-als.c b/drivers/iio/light/lm3533-als.c > index 99f0b903018c..853abb96e13f 100644 > --- a/drivers/iio/light/lm3533-als.c > +++ b/drivers/iio/light/lm3533-als.c > @@ -16,15 +16,18 @@ > #include <linux/module.h> > #include <linux/mutex.h> > #include <linux/mfd/core.h> > +#include <linux/mod_devicetable.h> > #include <linux/platform_device.h> > +#include <linux/property.h> > #include <linux/slab.h> > #include <linux/uaccess.h> > +#include <linux/units.h> > > #include <linux/mfd/lm3533.h> > > > -#define LM3533_ALS_RESISTOR_MIN 1 > -#define LM3533_ALS_RESISTOR_MAX 127 > +#define LM3533_ALS_RESISTOR_MIN 1575 > +#define LM3533_ALS_RESISTOR_MAX 200000 > #define LM3533_ALS_CHANNEL_CURRENT_MAX 2 > #define LM3533_ALS_THRESH_MAX 3 > #define LM3533_ALS_ZONE_MAX 4 > @@ -56,6 +59,9 @@ struct lm3533_als { > > atomic_t zone; > struct mutex thresh_mutex; > + > + bool pwm_mode; > + u32 r_select; > }; > > > @@ -714,64 +720,6 @@ static const struct attribute_group lm3533_als_attribute_group = { > .attrs = lm3533_als_attributes > }; > > -static int lm3533_als_set_input_mode(struct lm3533_als *als, bool pwm_mode) > -{ > - u8 mask = LM3533_ALS_INPUT_MODE_MASK; > - u8 val; > - int ret; > - > - if (pwm_mode) > - val = mask; /* pwm input */ > - else > - val = 0; /* analog input */ > - > - ret = lm3533_update(als->lm3533, LM3533_REG_ALS_CONF, val, mask); > - if (ret) { > - dev_err(&als->pdev->dev, "failed to set input mode %d\n", > - pwm_mode); > - return ret; > - } > - > - return 0; > -} > - > -static int lm3533_als_set_resistor(struct lm3533_als *als, u8 val) > -{ > - int ret; > - > - if (val < LM3533_ALS_RESISTOR_MIN || val > LM3533_ALS_RESISTOR_MAX) { > - dev_err(&als->pdev->dev, "invalid resistor value\n"); > - return -EINVAL; > - } > - > - ret = lm3533_write(als->lm3533, LM3533_REG_ALS_RESISTOR_SELECT, val); > - if (ret) { > - dev_err(&als->pdev->dev, "failed to set resistor\n"); > - return ret; > - } > - > - return 0; > -} > - > -static int lm3533_als_setup(struct lm3533_als *als, > - const struct lm3533_als_platform_data *pdata) > -{ > - int ret; > - > - ret = lm3533_als_set_input_mode(als, pdata->pwm_mode); > - if (ret) > - return ret; > - > - /* ALS input is always high impedance in PWM-mode. */ > - if (!pdata->pwm_mode) { > - ret = lm3533_als_set_resistor(als, pdata->r_select); > - if (ret) > - return ret; > - } > - > - return 0; > -} > - > static int lm3533_als_setup_irq(struct lm3533_als *als, void *dev) > { > u8 mask = LM3533_ALS_INT_ENABLE_MASK; > @@ -784,7 +732,8 @@ static int lm3533_als_setup_irq(struct lm3533_als *als, void *dev) > return ret; > } > > - ret = request_threaded_irq(als->irq, NULL, lm3533_als_isr, > + ret = devm_request_threaded_irq(&als->pdev->dev, als->irq, NULL, > + lm3533_als_isr, > IRQF_TRIGGER_LOW | IRQF_ONESHOT, > dev_name(&als->pdev->dev), dev); > if (ret) { > @@ -828,7 +777,6 @@ static const struct iio_info lm3533_als_info = { > > static int lm3533_als_probe(struct platform_device *pdev) > { > - const struct lm3533_als_platform_data *pdata; > struct lm3533 *lm3533; > struct lm3533_als *als; > struct iio_dev *indio_dev; > @@ -838,12 +786,6 @@ static int lm3533_als_probe(struct platform_device *pdev) > if (!lm3533) > return -EINVAL; > > - pdata = dev_get_platdata(&pdev->dev); > - if (!pdata) { > - dev_err(&pdev->dev, "no platform data\n"); > - return -EINVAL; > - } > - > indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*als)); > if (!indio_dev) > return -ENOMEM; > @@ -852,31 +794,52 @@ static int lm3533_als_probe(struct platform_device *pdev) > indio_dev->channels = lm3533_als_channels; > indio_dev->num_channels = ARRAY_SIZE(lm3533_als_channels); > indio_dev->name = dev_name(&pdev->dev); > - iio_device_set_parent(indio_dev, pdev->dev.parent); > indio_dev->modes = INDIO_DIRECT_MODE; > > als = iio_priv(indio_dev); > als->lm3533 = lm3533; > als->pdev = pdev; > - als->irq = lm3533->irq; > + als->irq = platform_get_irq_optional(pdev, 0); > atomic_set(&als->zone, 0); > mutex_init(&als->thresh_mutex); > > platform_set_drvdata(pdev, indio_dev); > > - if (als->irq) { > + if (als->irq > 0) { > ret = lm3533_als_setup_irq(als, indio_dev); > if (ret) > return ret; > } > > - ret = lm3533_als_setup(als, pdata); > + device_property_read_u32(&pdev->dev, "ti,resistor-value-ohm", > + &als->r_select); > + > + als->r_select = clamp(als->r_select, LM3533_ALS_RESISTOR_MIN, > + LM3533_ALS_RESISTOR_MAX); > + als->r_select = DIV_ROUND_UP(2 * MICRO, 10 * als->r_select); > + > + als->pwm_mode = device_property_read_bool(&pdev->dev, "ti,pwm-mode"); > + > + ret = lm3533_update(lm3533, LM3533_REG_ALS_CONF, als->pwm_mode ? > + LM3533_ALS_INPUT_MODE_MASK : 0, > + LM3533_ALS_INPUT_MODE_MASK); > if (ret) > - goto err_free_irq; > + return dev_err_probe(&pdev->dev, ret, > + "failed to set input mode %d\n", > + als->pwm_mode); > + > + /* ALS input is always high impedance in PWM-mode. */ > + if (!als->pwm_mode) { > + ret = lm3533_write(lm3533, LM3533_REG_ALS_RESISTOR_SELECT, > + (u8)als->r_select); > + if (ret) > + return dev_err_probe(&pdev->dev, ret, > + "failed to set resistor\n"); > + } > > ret = lm3533_als_enable(als); > if (ret) > - goto err_free_irq; > + return ret; > > ret = iio_device_register(indio_dev); > if (ret) { > @@ -888,9 +851,6 @@ static int lm3533_als_probe(struct platform_device *pdev) > > err_disable: > lm3533_als_disable(als); > -err_free_irq: > - if (als->irq) > - free_irq(als->irq, indio_dev); > > return ret; > } > @@ -903,13 +863,18 @@ static void lm3533_als_remove(struct platform_device *pdev) > lm3533_als_set_int_mode(indio_dev, false); > iio_device_unregister(indio_dev); > lm3533_als_disable(als); > - if (als->irq) > - free_irq(als->irq, indio_dev); > } > > +static const struct of_device_id lm3533_als_match_table[] = { > + { .compatible = "ti,lm3533-als" }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, lm3533_als_match_table); > + > static struct platform_driver lm3533_als_driver = { > .driver = { > .name = "lm3533-als", > + .of_match_table = lm3533_als_match_table, > }, > .probe = lm3533_als_probe, > .remove = lm3533_als_remove, > diff --git a/drivers/leds/leds-lm3533.c b/drivers/leds/leds-lm3533.c > index 45795f2a1042..f6345bc1f443 100644 > --- a/drivers/leds/leds-lm3533.c > +++ b/drivers/leds/leds-lm3533.c > @@ -10,8 +10,10 @@ > #include <linux/module.h> > #include <linux/leds.h> > #include <linux/mfd/core.h> > +#include <linux/mod_devicetable.h> > #include <linux/mutex.h> > #include <linux/platform_device.h> > +#include <linux/property.h> > #include <linux/slab.h> > > #include <linux/mfd/lm3533.h> > @@ -48,6 +50,9 @@ struct lm3533_led { > > struct mutex mutex; > unsigned long flags; > + > + u32 max_current; > + u32 pwm; > }; > > > @@ -632,22 +637,20 @@ static const struct attribute_group *lm3533_led_attribute_groups[] = { > NULL > }; > > -static int lm3533_led_setup(struct lm3533_led *led, > - struct lm3533_led_platform_data *pdata) > +static int lm3533_led_setup(struct lm3533_led *led) > { > int ret; > > - ret = lm3533_ctrlbank_set_max_current(&led->cb, pdata->max_current); > + ret = lm3533_ctrlbank_set_max_current(&led->cb, led->max_current); > if (ret) > return ret; > > - return lm3533_ctrlbank_set_pwm(&led->cb, pdata->pwm); > + return lm3533_ctrlbank_set_pwm(&led->cb, led->pwm); > } > > static int lm3533_led_probe(struct platform_device *pdev) > { > struct lm3533 *lm3533; > - struct lm3533_led_platform_data *pdata; > struct lm3533_led *led; > int ret; > > @@ -657,30 +660,30 @@ static int lm3533_led_probe(struct platform_device *pdev) > if (!lm3533) > return -EINVAL; > > - pdata = dev_get_platdata(&pdev->dev); > - if (!pdata) { > - dev_err(&pdev->dev, "no platform data\n"); > - return -EINVAL; > - } > - > - if (pdev->id < 0 || pdev->id >= LM3533_LVCTRLBANK_COUNT) { > - dev_err(&pdev->dev, "illegal LED id %d\n", pdev->id); > - return -EINVAL; > - } > + if (pdev->id < LM3533_LVCTRLBANK_MIN || pdev->id > LM3533_LVCTRLBANK_MAX) > + return dev_err_probe(&pdev->dev, -EINVAL, > + "illegal LED id %d\n", pdev->id); > > led = devm_kzalloc(&pdev->dev, sizeof(*led), GFP_KERNEL); > if (!led) > return -ENOMEM; > > led->lm3533 = lm3533; > - led->cdev.name = pdata->name; > - led->cdev.default_trigger = pdata->default_trigger; > led->cdev.brightness_set_blocking = lm3533_led_set; > led->cdev.brightness_get = lm3533_led_get; > led->cdev.blink_set = lm3533_led_blink_set; > led->cdev.brightness = LED_OFF; > led->cdev.groups = lm3533_led_attribute_groups; > - led->id = pdev->id; > + led->id = pdev->id - LM3533_LVCTRLBANK_MIN; > + > + led->cdev.name = devm_kasprintf(&pdev->dev, GFP_KERNEL, "%s-%d", > + pdev->name, led->id); > + if (!led->cdev.name) > + return -ENOMEM; > + > + led->cdev.default_trigger = "none"; > + device_property_read_string(&pdev->dev, "linux,default-trigger", > + &led->cdev.default_trigger); > > mutex_init(&led->mutex); > > @@ -694,15 +697,23 @@ static int lm3533_led_probe(struct platform_device *pdev) > > platform_set_drvdata(pdev, led); > > - ret = led_classdev_register(pdev->dev.parent, &led->cdev); > + ret = led_classdev_register(&pdev->dev, &led->cdev); > if (ret) { > - dev_err(&pdev->dev, "failed to register LED %d\n", pdev->id); > + dev_err(&pdev->dev, "failed to register LED %d\n", led->id); > return ret; > } > > led->cb.dev = led->cdev.dev; > > - ret = lm3533_led_setup(led, pdata); > + device_property_read_u32(&pdev->dev, "led-max-microamp", > + &led->max_current); > + led->max_current = clamp(led->max_current, LM3533_LED_MAX_CURRENT_MIN, > + LM3533_LED_MAX_CURRENT_MAX); > + > + led->pwm = 0; > + device_property_read_u32(&pdev->dev, "ti,pwm-config-mask", &led->pwm); > + > + ret = lm3533_led_setup(led); > if (ret) > goto err_deregister; > > @@ -739,9 +750,16 @@ static void lm3533_led_shutdown(struct platform_device *pdev) > lm3533_led_set(&led->cdev, LED_OFF); /* disable blink */ > } > > +static const struct of_device_id lm3533_led_match_table[] = { > + { .compatible = "ti,lm3533-leds" }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, lm3533_led_match_table); > + > static struct platform_driver lm3533_led_driver = { > .driver = { > .name = "lm3533-leds", > + .of_match_table = lm3533_led_match_table, > }, > .probe = lm3533_led_probe, > .remove = lm3533_led_remove, > diff --git a/drivers/mfd/lm3533-core.c b/drivers/mfd/lm3533-core.c > index 0a2409d00b2e..83ebd780f39d 100644 > --- a/drivers/mfd/lm3533-core.c > +++ b/drivers/mfd/lm3533-core.c > @@ -14,19 +14,26 @@ > #include <linux/gpio/consumer.h> > #include <linux/i2c.h> > #include <linux/mfd/core.h> > +#include <linux/mod_devicetable.h> > +#include <linux/property.h> > #include <linux/regmap.h> > #include <linux/seq_file.h> > #include <linux/slab.h> > #include <linux/uaccess.h> > +#include <linux/units.h> > > #include <linux/mfd/lm3533.h> > > > #define LM3533_BOOST_OVP_MASK 0x06 > #define LM3533_BOOST_OVP_SHIFT 1 > +#define LM3533_BOOST_OVP_MIN 16000000 > +#define LM3533_BOOST_OVP_MAX 40000000 > > #define LM3533_BOOST_FREQ_MASK 0x01 > #define LM3533_BOOST_FREQ_SHIFT 0 > +#define LM3533_BOOST_FREQ_MIN 500000 > +#define LM3533_BOOST_FREQ_MAX 1000000 > > #define LM3533_BL_ID_MASK 1 > #define LM3533_LED_ID_MASK 3 > @@ -42,42 +49,14 @@ > > #define LM3533_REG_MAX 0xb2 > > - > -static struct mfd_cell lm3533_als_devs[] = { > - { > - .name = "lm3533-als", > - .id = -1, > - }, > -}; > - > -static struct mfd_cell lm3533_bl_devs[] = { > - { > - .name = "lm3533-backlight", > - .id = 0, > - }, > - { > - .name = "lm3533-backlight", > - .id = 1, > - }, > -}; > - > -static struct mfd_cell lm3533_led_devs[] = { > - { > - .name = "lm3533-leds", > - .id = 0, > - }, > - { > - .name = "lm3533-leds", > - .id = 1, > - }, > - { > - .name = "lm3533-leds", > - .id = 2, > - }, > - { > - .name = "lm3533-leds", > - .id = 3, > - }, > +static struct mfd_cell lm3533_child_devices[] = { > + MFD_CELL_OF("lm3533-als", NULL, NULL, 0, 0, "ti,lm3533-als"), > + MFD_CELL_OF_REG("lm3533-backlight", NULL, NULL, 0, 0, "ti,lm3533-backlight", 0), > + MFD_CELL_OF_REG("lm3533-backlight", NULL, NULL, 0, 1, "ti,lm3533-backlight", 1), > + MFD_CELL_OF_REG("lm3533-leds", NULL, NULL, 0, 0, "ti,lm3533-leds", 2), > + MFD_CELL_OF_REG("lm3533-leds", NULL, NULL, 0, 1, "ti,lm3533-leds", 3), > + MFD_CELL_OF_REG("lm3533-leds", NULL, NULL, 0, 2, "ti,lm3533-leds", 4), > + MFD_CELL_OF_REG("lm3533-leds", NULL, NULL, 0, 3, "ti,lm3533-leds", 5), > }; > > int lm3533_read(struct lm3533 *lm3533, u8 reg, u8 *val) > @@ -132,35 +111,6 @@ int lm3533_update(struct lm3533 *lm3533, u8 reg, u8 val, u8 mask) > } > EXPORT_SYMBOL_GPL(lm3533_update); > > -static int lm3533_set_boost_freq(struct lm3533 *lm3533, > - enum lm3533_boost_freq freq) > -{ > - int ret; > - > - ret = lm3533_update(lm3533, LM3533_REG_BOOST_PWM, > - freq << LM3533_BOOST_FREQ_SHIFT, > - LM3533_BOOST_FREQ_MASK); > - if (ret) > - dev_err(lm3533->dev, "failed to set boost frequency\n"); > - > - return ret; > -} > - > - > -static int lm3533_set_boost_ovp(struct lm3533 *lm3533, > - enum lm3533_boost_ovp ovp) > -{ > - int ret; > - > - ret = lm3533_update(lm3533, LM3533_REG_BOOST_PWM, > - ovp << LM3533_BOOST_OVP_SHIFT, > - LM3533_BOOST_OVP_MASK); > - if (ret) > - dev_err(lm3533->dev, "failed to set boost ovp\n"); > - > - return ret; > -} > - > /* > * HVLED output config -- output hvled controlled by backlight bl > */ > @@ -376,136 +326,45 @@ static struct attribute_group lm3533_attribute_group = { > .attrs = lm3533_attributes > }; > > -static int lm3533_device_als_init(struct lm3533 *lm3533) > +static int lm3533_device_init(struct lm3533 *lm3533) > { > - struct lm3533_platform_data *pdata = dev_get_platdata(lm3533->dev); > + struct device *dev = lm3533->dev; > int ret; > > - if (!pdata->als) > - return 0; > - > - lm3533_als_devs[0].platform_data = pdata->als; > - lm3533_als_devs[0].pdata_size = sizeof(*pdata->als); > + lm3533_enable(lm3533); > > - ret = mfd_add_devices(lm3533->dev, 0, lm3533_als_devs, 1, NULL, > - 0, NULL); > + ret = lm3533_update(lm3533, LM3533_REG_BOOST_PWM, > + lm3533->boost_freq << LM3533_BOOST_FREQ_SHIFT, > + LM3533_BOOST_FREQ_MASK); > if (ret) { > - dev_err(lm3533->dev, "failed to add ALS device\n"); > - return ret; > - } > - > - lm3533->have_als = 1; > - > - return 0; > -} > - > -static int lm3533_device_bl_init(struct lm3533 *lm3533) > -{ > - struct lm3533_platform_data *pdata = dev_get_platdata(lm3533->dev); > - int i; > - int ret; > - > - if (!pdata->backlights || pdata->num_backlights == 0) > - return 0; > - > - if (pdata->num_backlights > ARRAY_SIZE(lm3533_bl_devs)) > - pdata->num_backlights = ARRAY_SIZE(lm3533_bl_devs); > - > - for (i = 0; i < pdata->num_backlights; ++i) { > - lm3533_bl_devs[i].platform_data = &pdata->backlights[i]; > - lm3533_bl_devs[i].pdata_size = sizeof(pdata->backlights[i]); > + dev_err(dev, "failed to set boost frequency\n"); > + goto err_disable; > } > > - ret = mfd_add_devices(lm3533->dev, 0, lm3533_bl_devs, > - pdata->num_backlights, NULL, 0, NULL); > + ret = lm3533_update(lm3533, LM3533_REG_BOOST_PWM, > + lm3533->boost_ovp << LM3533_BOOST_OVP_SHIFT, > + LM3533_BOOST_OVP_MASK); > if (ret) { > - dev_err(lm3533->dev, "failed to add backlight devices\n"); > - return ret; > - } > - > - lm3533->have_backlights = 1; > - > - return 0; > -} > - > -static int lm3533_device_led_init(struct lm3533 *lm3533) > -{ > - struct lm3533_platform_data *pdata = dev_get_platdata(lm3533->dev); > - int i; > - int ret; > - > - if (!pdata->leds || pdata->num_leds == 0) > - return 0; > - > - if (pdata->num_leds > ARRAY_SIZE(lm3533_led_devs)) > - pdata->num_leds = ARRAY_SIZE(lm3533_led_devs); > - > - for (i = 0; i < pdata->num_leds; ++i) { > - lm3533_led_devs[i].platform_data = &pdata->leds[i]; > - lm3533_led_devs[i].pdata_size = sizeof(pdata->leds[i]); > + dev_err(dev, "failed to set boost ovp\n"); > + goto err_disable; > } > > - ret = mfd_add_devices(lm3533->dev, 0, lm3533_led_devs, > - pdata->num_leds, NULL, 0, NULL); > + ret = devm_mfd_add_devices(dev, 0, lm3533_child_devices, > + ARRAY_SIZE(lm3533_child_devices), > + NULL, 0, NULL); Question to Lee Jones. Would you find acceptable if the driver will build cell list dynamically based on the nodes in the device tree? This is LED controller after all, not all leds can be populated and same LED control bank can be linked to all LVLEDs for example. If you are ok, would this implementation satisfy you? struct mfd_cell lm3533_cells[LM3533_CELLS_MAX]; u32 count = 0, reg; int ret; device_for_each_child_node_scoped(lm3533->dev, child) { if (!fwnode_device_is_available(child)) continue; if (count >= LM3533_CELLS_MAX) break; if (fwnode_device_is_compatible(child, "ti,lm3533-als")) { lm3533_cells[count].name = "lm3533-als"; lm3533_cells[count].id = PLATFORM_DEVID_NONE; lm3533_cells[count].of_compatible = "ti,lm3533-als"; lm3533->have_als = true; } if (fwnode_device_is_compatible(child, "ti,lm3533-backlight")) { ret = fwnode_property_read_u32(child, "reg", ®); if (ret || reg > LM3533_HVLED_ID_MAX) { dev_err(dev, "invalid backlight reg %d\n", reg); continue; } lm3533_cells[count].name = "lm3533-backlight"; lm3533_cells[count].id = reg; lm3533_cells[count].of_compatible = "ti,lm3533-backlight"; lm3533->have_backlights = true; } if (fwnode_device_is_compatible(child, "ti,lm3533-leds")) { ret = fwnode_property_read_u32(child, "reg", ®); if (ret || reg < LM3533_HVLED_ID_MAX || reg > LM3533_LVLED_ID_MAX) { dev_err(dev, "invalid LED reg %d\n", reg); continue; } lm3533_cells[count].name = "lm3533-leds"; lm3533_cells[count].id = reg - LM3533_HVLED_ID_MAX; lm3533_cells[count].of_compatible = "ti,lm3533-leds"; lm3533->have_leds = true; } count++; } > if (ret) { > - dev_err(lm3533->dev, "failed to add LED devices\n"); > - return ret; > - } > - > - lm3533->have_leds = 1; > - > - return 0; > -} > - > -static int lm3533_device_setup(struct lm3533 *lm3533, > - struct lm3533_platform_data *pdata) > -{ > - int ret; > - > - ret = lm3533_set_boost_freq(lm3533, pdata->boost_freq); > - if (ret) > - return ret; > - > - return lm3533_set_boost_ovp(lm3533, pdata->boost_ovp); > -} > - > -static int lm3533_device_init(struct lm3533 *lm3533) > -{ > - struct lm3533_platform_data *pdata = dev_get_platdata(lm3533->dev); > - int ret; > - > - dev_dbg(lm3533->dev, "%s\n", __func__); > - > - if (!pdata) { > - dev_err(lm3533->dev, "no platform data\n"); > - return -EINVAL; > + dev_err(dev, "failed to add MFD devices: %d\n", ret); > + goto err_disable; > } > > - lm3533->hwen = devm_gpiod_get(lm3533->dev, NULL, GPIOD_OUT_LOW); > - if (IS_ERR(lm3533->hwen)) > - return dev_err_probe(lm3533->dev, PTR_ERR(lm3533->hwen), "failed to request HWEN GPIO\n"); > - gpiod_set_consumer_name(lm3533->hwen, "lm3533-hwen"); > - > - lm3533_enable(lm3533); > - > - ret = lm3533_device_setup(lm3533, pdata); > - if (ret) > + ret = sysfs_create_group(&dev->kobj, &lm3533_attribute_group); > + if (ret) { > + dev_err(dev, "failed to create sysfs attributes\n"); > goto err_disable; > - > - lm3533_device_als_init(lm3533); > - lm3533_device_bl_init(lm3533); > - lm3533_device_led_init(lm3533); > - > - ret = sysfs_create_group(&lm3533->dev->kobj, &lm3533_attribute_group); > - if (ret < 0) { > - dev_err(lm3533->dev, "failed to create sysfs attributes\n"); > - goto err_unregister; > } > > return 0; > > -err_unregister: > - mfd_remove_devices(lm3533->dev); > err_disable: > lm3533_disable(lm3533); > > @@ -517,8 +376,6 @@ static void lm3533_device_exit(struct lm3533 *lm3533) > dev_dbg(lm3533->dev, "%s\n", __func__); > > sysfs_remove_group(&lm3533->dev->kobj, &lm3533_attribute_group); > - > - mfd_remove_devices(lm3533->dev); > lm3533_disable(lm3533); > } > > @@ -589,7 +446,40 @@ static int lm3533_i2c_probe(struct i2c_client *i2c) > return PTR_ERR(lm3533->regmap); > > lm3533->dev = &i2c->dev; > - lm3533->irq = i2c->irq; > + > + lm3533->hwen = devm_gpiod_get_optional(lm3533->dev, "enable", > + GPIOD_OUT_LOW); > + if (IS_ERR(lm3533->hwen)) > + return dev_err_probe(lm3533->dev, PTR_ERR(lm3533->hwen), > + "failed to get HWEN GPIO\n"); > + > + device_property_read_u32(lm3533->dev, "ti,boost-ovp-microvolt", > + &lm3533->boost_ovp); > + > + lm3533->boost_ovp = clamp(lm3533->boost_ovp, LM3533_BOOST_OVP_MIN, > + LM3533_BOOST_OVP_MAX); > + lm3533->boost_ovp = lm3533->boost_ovp / (8 * MICRO) - 2; > + > + device_property_read_u32(lm3533->dev, "ti,boost-freq-hz", > + &lm3533->boost_freq); > + > + lm3533->boost_freq = clamp(lm3533->boost_freq, LM3533_BOOST_FREQ_MIN, > + LM3533_BOOST_FREQ_MAX); > + lm3533->boost_freq = lm3533->boost_freq / (500 * KILO) - 1; > + > + device_for_each_child_node_scoped(lm3533->dev, child) { > + if (!fwnode_device_is_available(child)) > + continue; > + > + if (fwnode_device_is_compatible(child, "ti,lm3533-als")) > + lm3533->have_als = true; > + > + if (fwnode_device_is_compatible(child, "ti,lm3533-backlight")) > + lm3533->have_backlights = true; > + > + if (fwnode_device_is_compatible(child, "ti,lm3533-leds")) > + lm3533->have_leds = true; > + } > > return lm3533_device_init(lm3533); > } > @@ -603,6 +493,12 @@ static void lm3533_i2c_remove(struct i2c_client *i2c) > lm3533_device_exit(lm3533); > } > > +static const struct of_device_id lm3533_match_table[] = { > + { .compatible = "ti,lm3533" }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, lm3533_match_table); > + > static const struct i2c_device_id lm3533_i2c_ids[] = { > { "lm3533" }, > { } > @@ -612,6 +508,7 @@ MODULE_DEVICE_TABLE(i2c, lm3533_i2c_ids); > static struct i2c_driver lm3533_i2c_driver = { > .driver = { > .name = "lm3533", > + .of_match_table = lm3533_match_table, > }, > .id_table = lm3533_i2c_ids, > .probe = lm3533_i2c_probe, > diff --git a/drivers/video/backlight/lm3533_bl.c b/drivers/video/backlight/lm3533_bl.c > index babfd3ceec86..42da652df58d 100644 > --- a/drivers/video/backlight/lm3533_bl.c > +++ b/drivers/video/backlight/lm3533_bl.c > @@ -9,7 +9,9 @@ > > #include <linux/module.h> > #include <linux/init.h> > +#include <linux/mod_devicetable.h> > #include <linux/platform_device.h> > +#include <linux/property.h> > #include <linux/backlight.h> > #include <linux/slab.h> > > @@ -27,6 +29,9 @@ struct lm3533_bl { > struct lm3533_ctrlbank cb; > struct backlight_device *bd; > int id; > + > + u32 max_current; > + u32 pwm; > }; > > > @@ -246,25 +251,24 @@ static struct attribute_group lm3533_bl_attribute_group = { > .attrs = lm3533_bl_attributes > }; > > -static int lm3533_bl_setup(struct lm3533_bl *bl, > - struct lm3533_bl_platform_data *pdata) > +static int lm3533_bl_setup(struct lm3533_bl *bl) > { > int ret; > > - ret = lm3533_ctrlbank_set_max_current(&bl->cb, pdata->max_current); > + ret = lm3533_ctrlbank_set_max_current(&bl->cb, bl->max_current); > if (ret) > return ret; > > - return lm3533_ctrlbank_set_pwm(&bl->cb, pdata->pwm); > + return lm3533_ctrlbank_set_pwm(&bl->cb, bl->pwm); > } > > static int lm3533_bl_probe(struct platform_device *pdev) > { > struct lm3533 *lm3533; > - struct lm3533_bl_platform_data *pdata; > struct lm3533_bl *bl; > struct backlight_device *bd; > struct backlight_properties props; > + char *name = NULL; > int ret; > > dev_dbg(&pdev->dev, "%s\n", __func__); > @@ -273,12 +277,6 @@ static int lm3533_bl_probe(struct platform_device *pdev) > if (!lm3533) > return -EINVAL; > > - pdata = dev_get_platdata(&pdev->dev); > - if (!pdata) { > - dev_err(&pdev->dev, "no platform data\n"); > - return -EINVAL; > - } > - > if (pdev->id < 0 || pdev->id >= LM3533_HVCTRLBANK_COUNT) { > dev_err(&pdev->dev, "illegal backlight id %d\n", pdev->id); > return -EINVAL; > @@ -295,13 +293,20 @@ static int lm3533_bl_probe(struct platform_device *pdev) > bl->cb.id = lm3533_bl_get_ctrlbank_id(bl); > bl->cb.dev = NULL; /* until registered */ > > + name = devm_kasprintf(&pdev->dev, GFP_KERNEL, "%s-%d", > + pdev->name, pdev->id); > + if (!name) > + return -ENOMEM; > + > memset(&props, 0, sizeof(props)); > props.type = BACKLIGHT_RAW; > props.max_brightness = LM3533_BL_MAX_BRIGHTNESS; > - props.brightness = pdata->default_brightness; > - bd = devm_backlight_device_register(&pdev->dev, pdata->name, > - pdev->dev.parent, bl, &lm3533_bl_ops, > - &props); > + props.brightness = LM3533_BL_MAX_BRIGHTNESS; > + device_property_read_u32(&pdev->dev, "default-brightness", > + &props.brightness); > + > + bd = devm_backlight_device_register(&pdev->dev, name, &pdev->dev, > + bl, &lm3533_bl_ops, &props); > if (IS_ERR(bd)) { > dev_err(&pdev->dev, "failed to register backlight device\n"); > return PTR_ERR(bd); > @@ -320,7 +325,15 @@ static int lm3533_bl_probe(struct platform_device *pdev) > > backlight_update_status(bd); > > - ret = lm3533_bl_setup(bl, pdata); > + device_property_read_u32(&pdev->dev, "led-max-microamp", > + &bl->max_current); > + bl->max_current = clamp(bl->max_current, LM3533_LED_MAX_CURRENT_MIN, > + LM3533_LED_MAX_CURRENT_MAX); > + > + bl->pwm = 0; > + device_property_read_u32(&pdev->dev, "ti,pwm-config-mask", &bl->pwm); > + > + ret = lm3533_bl_setup(bl); > if (ret) > goto err_sysfs_remove; > > @@ -381,10 +394,17 @@ static void lm3533_bl_shutdown(struct platform_device *pdev) > lm3533_ctrlbank_disable(&bl->cb); > } > > +static const struct of_device_id lm3533_bl_match_table[] = { > + { .compatible = "ti,lm3533-backlight" }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, lm3533_bl_match_table); > + > static struct platform_driver lm3533_bl_driver = { > .driver = { > .name = "lm3533-backlight", > .pm = &lm3533_bl_pm_ops, > + .of_match_table = lm3533_bl_match_table, > }, > .probe = lm3533_bl_probe, > .remove = lm3533_bl_remove, > diff --git a/include/linux/mfd/lm3533.h b/include/linux/mfd/lm3533.h > index 69059a7a2ce5..3aa962d4c747 100644 > --- a/include/linux/mfd/lm3533.h > +++ b/include/linux/mfd/lm3533.h > @@ -15,6 +15,9 @@ > #define LM3533_ATTR_RW(_name) \ > DEVICE_ATTR(_name, S_IRUGO | S_IWUSR , show_##_name, store_##_name) > > +#define LM3533_LED_MAX_CURRENT_MIN 5000 > +#define LM3533_LED_MAX_CURRENT_MAX 29800 > + > struct device; > struct gpio_desc; > struct regmap; > @@ -25,7 +28,9 @@ struct lm3533 { > struct regmap *regmap; > > struct gpio_desc *hwen; > - int irq; > + > + u32 boost_ovp; > + u32 boost_freq; > > unsigned have_als:1; > unsigned have_backlights:1; > @@ -38,50 +43,6 @@ struct lm3533_ctrlbank { > int id; > }; > > -struct lm3533_als_platform_data { > - unsigned pwm_mode:1; /* PWM input mode (default analog) */ > - u8 r_select; /* 1 - 127 (ignored in PWM-mode) */ > -}; > - > -struct lm3533_bl_platform_data { > - char *name; > - u16 max_current; /* 5000 - 29800 uA (800 uA step) */ > - u8 default_brightness; /* 0 - 255 */ > - u8 pwm; /* 0 - 0x3f */ > -}; > - > -struct lm3533_led_platform_data { > - char *name; > - const char *default_trigger; > - u16 max_current; /* 5000 - 29800 uA (800 uA step) */ > - u8 pwm; /* 0 - 0x3f */ > -}; > - > -enum lm3533_boost_freq { > - LM3533_BOOST_FREQ_500KHZ, > - LM3533_BOOST_FREQ_1000KHZ, > -}; > - > -enum lm3533_boost_ovp { > - LM3533_BOOST_OVP_16V, > - LM3533_BOOST_OVP_24V, > - LM3533_BOOST_OVP_32V, > - LM3533_BOOST_OVP_40V, > -}; > - > -struct lm3533_platform_data { > - enum lm3533_boost_ovp boost_ovp; > - enum lm3533_boost_freq boost_freq; > - > - struct lm3533_als_platform_data *als; > - > - struct lm3533_bl_platform_data *backlights; > - int num_backlights; > - > - struct lm3533_led_platform_data *leds; > - int num_leds; > -}; > - > extern int lm3533_ctrlbank_enable(struct lm3533_ctrlbank *cb); > extern int lm3533_ctrlbank_disable(struct lm3533_ctrlbank *cb); > > -- > 2.51.0 > ^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v1 3/6] mfd: lm3533: Add support for VIN power supply 2026-05-17 7:43 [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support Svyatoslav Ryhel 2026-05-17 7:43 ` [PATCH v1 1/6] dt-bindings: leds: Document TI LM3533 LED controller Svyatoslav Ryhel 2026-05-17 7:43 ` [PATCH v1 2/6] mfd: lm3533: Convert to use OF bindings Svyatoslav Ryhel @ 2026-05-17 7:43 ` Svyatoslav Ryhel 2026-05-17 7:43 ` [PATCH v1 4/6] mfd: lm3533: set DMA mask Svyatoslav Ryhel ` (3 subsequent siblings) 6 siblings, 0 replies; 18+ messages in thread From: Svyatoslav Ryhel @ 2026-05-17 7:43 UTC (permalink / raw) To: Lee Jones, Daniel Thompson, Jingoo Han, Pavel Machek, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko, Helge Deller, Svyatoslav Ryhel Cc: dri-devel, linux-leds, devicetree, linux-kernel, linux-iio, linux-fbdev Add support for 2.7V-5.5V VIN power supply. Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> --- drivers/mfd/lm3533-core.c | 22 ++++++++++++++++++++-- include/linux/mfd/lm3533.h | 1 + 2 files changed, 21 insertions(+), 2 deletions(-) diff --git a/drivers/mfd/lm3533-core.c b/drivers/mfd/lm3533-core.c index 83ebd780f39d..131eb1a1c8eb 100644 --- a/drivers/mfd/lm3533-core.c +++ b/drivers/mfd/lm3533-core.c @@ -173,14 +173,25 @@ static int lm3533_set_lvled_config(struct lm3533 *lm3533, u8 lvled, u8 led) return ret; } -static void lm3533_enable(struct lm3533 *lm3533) +static int lm3533_enable(struct lm3533 *lm3533) { + int ret; + + ret = regulator_enable(lm3533->vin_supply); + if (ret) { + dev_err(lm3533->dev, "failed to enable vin power supply\n"); + return ret; + } + gpiod_set_value(lm3533->hwen, 1); + + return 0; } static void lm3533_disable(struct lm3533 *lm3533) { gpiod_set_value(lm3533->hwen, 0); + regulator_disable(lm3533->vin_supply); } enum lm3533_attribute_type { @@ -331,7 +342,9 @@ static int lm3533_device_init(struct lm3533 *lm3533) struct device *dev = lm3533->dev; int ret; - lm3533_enable(lm3533); + ret = lm3533_enable(lm3533); + if (ret) + return ret; ret = lm3533_update(lm3533, LM3533_REG_BOOST_PWM, lm3533->boost_freq << LM3533_BOOST_FREQ_SHIFT, @@ -453,6 +466,11 @@ static int lm3533_i2c_probe(struct i2c_client *i2c) return dev_err_probe(lm3533->dev, PTR_ERR(lm3533->hwen), "failed to get HWEN GPIO\n"); + lm3533->vin_supply = devm_regulator_get(lm3533->dev, "vin"); + if (IS_ERR(lm3533->vin_supply)) + return dev_err_probe(lm3533->dev, PTR_ERR(lm3533->vin_supply), + "failed to get vin-supply\n"); + device_property_read_u32(lm3533->dev, "ti,boost-ovp-microvolt", &lm3533->boost_ovp); diff --git a/include/linux/mfd/lm3533.h b/include/linux/mfd/lm3533.h index 3aa962d4c747..e355a3ac982e 100644 --- a/include/linux/mfd/lm3533.h +++ b/include/linux/mfd/lm3533.h @@ -28,6 +28,7 @@ struct lm3533 { struct regmap *regmap; struct gpio_desc *hwen; + struct regulator *vin_supply; u32 boost_ovp; u32 boost_freq; -- 2.51.0 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v1 4/6] mfd: lm3533: set DMA mask 2026-05-17 7:43 [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support Svyatoslav Ryhel ` (2 preceding siblings ...) 2026-05-17 7:43 ` [PATCH v1 3/6] mfd: lm3533: Add support for VIN power supply Svyatoslav Ryhel @ 2026-05-17 7:43 ` Svyatoslav Ryhel 2026-05-17 7:43 ` [PATCH v1 5/6] video: backlight: lm3533_bl: Set initial mapping mode from DT Svyatoslav Ryhel ` (2 subsequent siblings) 6 siblings, 0 replies; 18+ messages in thread From: Svyatoslav Ryhel @ 2026-05-17 7:43 UTC (permalink / raw) To: Lee Jones, Daniel Thompson, Jingoo Han, Pavel Machek, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko, Helge Deller, Svyatoslav Ryhel Cc: dri-devel, linux-leds, devicetree, linux-kernel, linux-iio, linux-fbdev Missing coherent_dma_mask assigning triggers the following warning in dmesg: [ 3.287872] platform lm3533-backlight.0: DMA mask not set Since this warning might be elevated to an error in the future, set coherent_dma_mask to zero because both the core and cells do not utilize DMA. Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> --- drivers/mfd/lm3533-core.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/mfd/lm3533-core.c b/drivers/mfd/lm3533-core.c index 131eb1a1c8eb..c7914afd564c 100644 --- a/drivers/mfd/lm3533-core.c +++ b/drivers/mfd/lm3533-core.c @@ -499,6 +499,10 @@ static int lm3533_i2c_probe(struct i2c_client *i2c) lm3533->have_leds = true; } + /* Parent I2C controller uses DMA, LM3533 and child devices do not */ + i2c->dev.coherent_dma_mask = 0; + i2c->dev.dma_mask = &i2c->dev.coherent_dma_mask; + return lm3533_device_init(lm3533); } -- 2.51.0 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v1 5/6] video: backlight: lm3533_bl: Set initial mapping mode from DT 2026-05-17 7:43 [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support Svyatoslav Ryhel ` (3 preceding siblings ...) 2026-05-17 7:43 ` [PATCH v1 4/6] mfd: lm3533: set DMA mask Svyatoslav Ryhel @ 2026-05-17 7:43 ` Svyatoslav Ryhel 2026-05-17 7:43 ` [PATCH v1 6/6] video: leds: backlight: lm3533: Support getting LED sources " Svyatoslav Ryhel 2026-05-17 7:59 ` [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support Andy Shevchenko 6 siblings, 0 replies; 18+ messages in thread From: Svyatoslav Ryhel @ 2026-05-17 7:43 UTC (permalink / raw) To: Lee Jones, Daniel Thompson, Jingoo Han, Pavel Machek, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko, Helge Deller, Svyatoslav Ryhel Cc: dri-devel, linux-leds, devicetree, linux-kernel, linux-iio, linux-fbdev Add support to obtain the initial mapping mode from DT instead of leaving it unconfigured. Additionally, update the linear sysfs code, which uses a similar coding pattern. Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> --- drivers/video/backlight/lm3533_bl.c | 32 ++++++++++++++++------------- 1 file changed, 18 insertions(+), 14 deletions(-) diff --git a/drivers/video/backlight/lm3533_bl.c b/drivers/video/backlight/lm3533_bl.c index 42da652df58d..be9114b7e0ad 100644 --- a/drivers/video/backlight/lm3533_bl.c +++ b/drivers/video/backlight/lm3533_bl.c @@ -22,6 +22,7 @@ #define LM3533_BL_MAX_BRIGHTNESS 255 #define LM3533_REG_CTRLBANK_AB_BCONF 0x1a +#define CTRLBANK_AB_BCONF_MODE(n) BIT(2 * (n) + 1) struct lm3533_bl { @@ -32,6 +33,7 @@ struct lm3533_bl { u32 max_current; u32 pwm; + bool linear; }; @@ -135,8 +137,9 @@ static ssize_t show_linear(struct device *dev, struct device_attribute *attr, char *buf) { struct lm3533_bl *bl = dev_get_drvdata(dev); + int id = lm3533_bl_get_ctrlbank_id(bl); + u8 mask = CTRLBANK_AB_BCONF_MODE(id); u8 val; - u8 mask; int linear; int ret; @@ -144,8 +147,6 @@ static ssize_t show_linear(struct device *dev, if (ret) return ret; - mask = 1 << (2 * lm3533_bl_get_ctrlbank_id(bl) + 1); - if (val & mask) linear = 1; else @@ -159,23 +160,16 @@ static ssize_t store_linear(struct device *dev, const char *buf, size_t len) { struct lm3533_bl *bl = dev_get_drvdata(dev); + int id = lm3533_bl_get_ctrlbank_id(bl); unsigned long linear; - u8 mask; - u8 val; int ret; if (kstrtoul(buf, 0, &linear)) return -EINVAL; - mask = 1 << (2 * lm3533_bl_get_ctrlbank_id(bl) + 1); - - if (linear) - val = mask; - else - val = 0; - - ret = lm3533_update(bl->lm3533, LM3533_REG_CTRLBANK_AB_BCONF, val, - mask); + ret = lm3533_update(bl->lm3533, LM3533_REG_CTRLBANK_AB_BCONF, + linear ? CTRLBANK_AB_BCONF_MODE(id) : 0, + CTRLBANK_AB_BCONF_MODE(id)); if (ret) return ret; @@ -253,8 +247,15 @@ static struct attribute_group lm3533_bl_attribute_group = { static int lm3533_bl_setup(struct lm3533_bl *bl) { + int id = lm3533_bl_get_ctrlbank_id(bl); int ret; + ret = lm3533_update(bl->lm3533, LM3533_REG_CTRLBANK_AB_BCONF, + bl->linear ? CTRLBANK_AB_BCONF_MODE(id) : 0, + CTRLBANK_AB_BCONF_MODE(id)); + if (ret) + return ret; + ret = lm3533_ctrlbank_set_max_current(&bl->cb, bl->max_current); if (ret) return ret; @@ -333,6 +334,9 @@ static int lm3533_bl_probe(struct platform_device *pdev) bl->pwm = 0; device_property_read_u32(&pdev->dev, "ti,pwm-config-mask", &bl->pwm); + bl->linear = device_property_read_bool(&pdev->dev, + "ti,linear-mapping-mode"); + ret = lm3533_bl_setup(bl); if (ret) goto err_sysfs_remove; -- 2.51.0 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v1 6/6] video: leds: backlight: lm3533: Support getting LED sources from DT 2026-05-17 7:43 [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support Svyatoslav Ryhel ` (4 preceding siblings ...) 2026-05-17 7:43 ` [PATCH v1 5/6] video: backlight: lm3533_bl: Set initial mapping mode from DT Svyatoslav Ryhel @ 2026-05-17 7:43 ` Svyatoslav Ryhel 2026-05-17 7:59 ` [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support Andy Shevchenko 6 siblings, 0 replies; 18+ messages in thread From: Svyatoslav Ryhel @ 2026-05-17 7:43 UTC (permalink / raw) To: Lee Jones, Daniel Thompson, Jingoo Han, Pavel Machek, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko, Helge Deller, Svyatoslav Ryhel Cc: dri-devel, linux-leds, devicetree, linux-kernel, linux-iio, linux-fbdev Add Control Bank to HVLED/LVLED muxing support based on the led-sources defined in the device tree. Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> --- drivers/leds/leds-lm3533.c | 55 +++++++++++++++++++++++++++-- drivers/video/backlight/lm3533_bl.c | 39 +++++++++++++++++++- 2 files changed, 91 insertions(+), 3 deletions(-) diff --git a/drivers/leds/leds-lm3533.c b/drivers/leds/leds-lm3533.c index f6345bc1f443..c4eaf30880a1 100644 --- a/drivers/leds/leds-lm3533.c +++ b/drivers/leds/leds-lm3533.c @@ -7,6 +7,7 @@ * Author: Johan Hovold <jhovold@gmail.com> */ +#include <linux/bits.h> #include <linux/module.h> #include <linux/leds.h> #include <linux/mfd/core.h> @@ -26,6 +27,12 @@ #define LM3533_ALS_CHANNEL_LV_MIN 1 #define LM3533_ALS_CHANNEL_LV_MAX 2 +#define LM3533_REG_OUTPUT_CONF1 0x10 +#define OUTPUT_CONF1_MASK GENMASK(7, 2) +#define OUTPUT_CONF1_SHIFT 2 +#define LM3533_REG_OUTPUT_CONF2 0x11 +#define OUTPUT_CONF2_MASK GENMASK(3, 0) +#define OUTPUT_CONF2_SHIFT 6 #define LM3533_REG_CTRLBANK_BCONF_BASE 0x1b #define LM3533_REG_PATTERN_ENABLE 0x28 #define LM3533_REG_PATTERN_LOW_TIME_BASE 0x71 @@ -40,7 +47,7 @@ #define LM3533_REG_CTRLBANK_BCONF_ALS_CHANNEL_MASK 0x01 #define LM3533_LED_FLAG_PATTERN_ENABLE 1 - +#define LM3533_MAX_LEDS 5 struct lm3533_led { struct lm3533 *lm3533; @@ -53,6 +60,9 @@ struct lm3533_led { u32 max_current; u32 pwm; + + u32 num_leds; + u32 leds[LM3533_MAX_LEDS]; }; @@ -639,7 +649,30 @@ static const struct attribute_group *lm3533_led_attribute_groups[] = { static int lm3533_led_setup(struct lm3533_led *led) { - int ret; + u32 output_cfg_shift = 0; + u32 output_cfg_val = 0; + int ret, i; + + if (led->num_leds) { + for (i = 0; i < led->num_leds; i++) { + output_cfg_shift = led->leds[i] * 2; + output_cfg_val |= led->id << output_cfg_shift; + } + + /* LVLED1, LVLED2 and LVLED3 */ + ret = lm3533_update(led->lm3533, LM3533_REG_OUTPUT_CONF1, + output_cfg_val << OUTPUT_CONF1_SHIFT, + OUTPUT_CONF1_MASK); + if (ret) + return ret; + + /* LVLED4 and LVLED5 */ + ret = lm3533_update(led->lm3533, LM3533_REG_OUTPUT_CONF1, + output_cfg_val >> OUTPUT_CONF2_SHIFT, + OUTPUT_CONF2_MASK); + if (ret) + return ret; + } ret = lm3533_ctrlbank_set_max_current(&led->cb, led->max_current); if (ret) @@ -713,6 +746,24 @@ static int lm3533_led_probe(struct platform_device *pdev) led->pwm = 0; device_property_read_u32(&pdev->dev, "ti,pwm-config-mask", &led->pwm); + led->num_leds = device_property_count_u32(&pdev->dev, "led-sources"); + + /* + * If led-sources property is not set then either this Control Bank uses + * its default LVLED or is not linked to any LVLED at all. + */ + if (led->num_leds <= 0 || led->num_leds > LM3533_MAX_LEDS) + led->num_leds = 0; + + if (led->num_leds > 0 && led->num_leds < LM3533_MAX_LEDS) { + ret = device_property_read_u32_array(&pdev->dev, "led-sources", + led->leds, led->num_leds); + if (ret) { + dev_err(&pdev->dev, "failed to get led-sources\n"); + goto err_deregister; + } + } + ret = lm3533_led_setup(led); if (ret) goto err_deregister; diff --git a/drivers/video/backlight/lm3533_bl.c b/drivers/video/backlight/lm3533_bl.c index be9114b7e0ad..2898cb229643 100644 --- a/drivers/video/backlight/lm3533_bl.c +++ b/drivers/video/backlight/lm3533_bl.c @@ -7,6 +7,7 @@ * Author: Johan Hovold <jhovold@gmail.com> */ +#include <linux/bits.h> #include <linux/module.h> #include <linux/init.h> #include <linux/mod_devicetable.h> @@ -21,9 +22,12 @@ #define LM3533_HVCTRLBANK_COUNT 2 #define LM3533_BL_MAX_BRIGHTNESS 255 +#define LM3533_REG_OUTPUT_CONF1 0x10 +#define OUTPUT_CONF1_MASK GENMASK(1, 0) #define LM3533_REG_CTRLBANK_AB_BCONF 0x1a #define CTRLBANK_AB_BCONF_MODE(n) BIT(2 * (n) + 1) +#define LM3533_MAX_LED_STRINGS 2 struct lm3533_bl { struct lm3533 *lm3533; @@ -34,6 +38,9 @@ struct lm3533_bl { u32 max_current; u32 pwm; bool linear; + + u32 num_leds; + u32 led_strings[LM3533_MAX_LED_STRINGS]; }; @@ -248,7 +255,8 @@ static struct attribute_group lm3533_bl_attribute_group = { static int lm3533_bl_setup(struct lm3533_bl *bl) { int id = lm3533_bl_get_ctrlbank_id(bl); - int ret; + u32 output_cfg_val = 0; + int ret, i; ret = lm3533_update(bl->lm3533, LM3533_REG_CTRLBANK_AB_BCONF, bl->linear ? CTRLBANK_AB_BCONF_MODE(id) : 0, @@ -256,6 +264,16 @@ static int lm3533_bl_setup(struct lm3533_bl *bl) if (ret) return ret; + if (bl->num_leds) { + for (i = 0; i < bl->num_leds; i++) + output_cfg_val |= id << bl->led_strings[i]; + + ret = lm3533_update(bl->lm3533, LM3533_REG_OUTPUT_CONF1, + output_cfg_val, OUTPUT_CONF1_MASK); + if (ret) + return ret; + } + ret = lm3533_ctrlbank_set_max_current(&bl->cb, bl->max_current); if (ret) return ret; @@ -337,6 +355,25 @@ static int lm3533_bl_probe(struct platform_device *pdev) bl->linear = device_property_read_bool(&pdev->dev, "ti,linear-mapping-mode"); + bl->num_leds = device_property_count_u32(&pdev->dev, "led-sources"); + + /* + * If led-sources property is not set then either this Control Bank uses + * its default HVLED or is not linked to any HVLED at all. + */ + if (bl->num_leds <= 0 || bl->num_leds > LM3533_MAX_LED_STRINGS) + bl->num_leds = 0; + + if (bl->num_leds > 0 && bl->num_leds < LM3533_MAX_LED_STRINGS) { + ret = device_property_read_u32_array(&pdev->dev, "led-sources", + bl->led_strings, + bl->num_leds); + if (ret) { + dev_err(&pdev->dev, "failed to get led-sources\n"); + goto err_sysfs_remove; + } + } + ret = lm3533_bl_setup(bl); if (ret) goto err_sysfs_remove; -- 2.51.0 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support 2026-05-17 7:43 [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support Svyatoslav Ryhel ` (5 preceding siblings ...) 2026-05-17 7:43 ` [PATCH v1 6/6] video: leds: backlight: lm3533: Support getting LED sources " Svyatoslav Ryhel @ 2026-05-17 7:59 ` Andy Shevchenko 2026-05-17 10:13 ` Svyatoslav Ryhel 6 siblings, 1 reply; 18+ messages in thread From: Andy Shevchenko @ 2026-05-17 7:59 UTC (permalink / raw) To: Svyatoslav Ryhel Cc: Lee Jones, Daniel Thompson, Jingoo Han, Pavel Machek, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko, Helge Deller, dri-devel, linux-leds, devicetree, linux-kernel, linux-iio, linux-fbdev On Sun, May 17, 2026 at 10:43:00AM +0300, Svyatoslav Ryhel wrote: > Convert LM3533 to OF bindings, add missing VIN supply, add support for > setting mapping mode and LED sources based on device tree. How is this being different to https://lore.kernel.org/lkml/20250218132702.114669-1-clamor95@gmail.com/ ? What about this comment https://lore.kernel.org/lkml/ZmBcvtLCzllQDWVX@hovoldconsulting.com/ ? Have you talked to Bjorn A and Johan? -- With Best Regards, Andy Shevchenko ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support 2026-05-17 7:59 ` [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support Andy Shevchenko @ 2026-05-17 10:13 ` Svyatoslav Ryhel 2026-05-17 10:20 ` Andy Shevchenko 0 siblings, 1 reply; 18+ messages in thread From: Svyatoslav Ryhel @ 2026-05-17 10:13 UTC (permalink / raw) To: Andy Shevchenko Cc: Lee Jones, Daniel Thompson, Jingoo Han, Pavel Machek, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko, Helge Deller, dri-devel, linux-leds, devicetree, linux-kernel, linux-iio, linux-fbdev нд, 17 трав. 2026 р. о 10:59 Andy Shevchenko <andriy.shevchenko@intel.com> пише: > > On Sun, May 17, 2026 at 10:43:00AM +0300, Svyatoslav Ryhel wrote: > > Convert LM3533 to OF bindings, add missing VIN supply, add support for > > setting mapping mode and LED sources based on device tree. > > How is this being different to > https://lore.kernel.org/lkml/20250218132702.114669-1-clamor95@gmail.com/ > ? > I have decided to have a fresh look, this is continuation. > What about this comment > https://lore.kernel.org/lkml/ZmBcvtLCzllQDWVX@hovoldconsulting.com/ > ? Have you talked to Bjorn A and Johan? > No, but since grep -r "lm3533_platform_data" * gives 0 results there are no platform_data users of lm3533. > -- > With Best Regards, > Andy Shevchenko > > ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support 2026-05-17 10:13 ` Svyatoslav Ryhel @ 2026-05-17 10:20 ` Andy Shevchenko 2026-05-17 10:34 ` Svyatoslav Ryhel 0 siblings, 1 reply; 18+ messages in thread From: Andy Shevchenko @ 2026-05-17 10:20 UTC (permalink / raw) To: Svyatoslav Ryhel Cc: Lee Jones, Daniel Thompson, Jingoo Han, Pavel Machek, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko, Helge Deller, dri-devel, linux-leds, devicetree, linux-kernel, linux-iio, linux-fbdev On Sun, May 17, 2026 at 01:13:22PM +0300, Svyatoslav Ryhel wrote: > нд, 17 трав. 2026 р. о 10:59 Andy Shevchenko <andriy.shevchenko@intel.com> пише: > > On Sun, May 17, 2026 at 10:43:00AM +0300, Svyatoslav Ryhel wrote: > > > Convert LM3533 to OF bindings, add missing VIN supply, add support for > > > setting mapping mode and LED sources based on device tree. > > > > How is this being different to > > https://lore.kernel.org/lkml/20250218132702.114669-1-clamor95@gmail.com/ > > ? > > I have decided to have a fresh look, this is continuation. Then it should be something like v4? > > What about this comment > > https://lore.kernel.org/lkml/ZmBcvtLCzllQDWVX@hovoldconsulting.com/ > > ? Have you talked to Bjorn A and Johan? > > No, but since grep -r "lm3533_platform_data" * gives 0 results there > are no platform_data users of lm3533. Johan was against driver removal (while it sounds logical due to above) and referred to some other patches from somebody else. I think you need to synchronise with the people to have a clear roadmap that all stakeholders are agree with. With that, the split and other technical issues can be solved during the normal process. -- With Best Regards, Andy Shevchenko ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support 2026-05-17 10:20 ` Andy Shevchenko @ 2026-05-17 10:34 ` Svyatoslav Ryhel 2026-05-17 10:40 ` Andy Shevchenko 0 siblings, 1 reply; 18+ messages in thread From: Svyatoslav Ryhel @ 2026-05-17 10:34 UTC (permalink / raw) To: Andy Shevchenko Cc: Lee Jones, Daniel Thompson, Jingoo Han, Pavel Machek, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko, Helge Deller, dri-devel, linux-leds, devicetree, linux-kernel, linux-iio, linux-fbdev нд, 17 трав. 2026 р. о 13:20 Andy Shevchenko <andriy.shevchenko@intel.com> пише: > > On Sun, May 17, 2026 at 01:13:22PM +0300, Svyatoslav Ryhel wrote: > > нд, 17 трав. 2026 р. о 10:59 Andy Shevchenko <andriy.shevchenko@intel.com> пише: > > > On Sun, May 17, 2026 at 10:43:00AM +0300, Svyatoslav Ryhel wrote: > > > > Convert LM3533 to OF bindings, add missing VIN supply, add support for > > > > setting mapping mode and LED sources based on device tree. > > > > > > How is this being different to > > > https://lore.kernel.org/lkml/20250218132702.114669-1-clamor95@gmail.com/ > > > ? > > > > I have decided to have a fresh look, this is continuation. > > Then it should be something like v4? > That was more than a year ago, lets start fresh. Those patches are gone, though I did add many of suggestions from there. > > > What about this comment > > > https://lore.kernel.org/lkml/ZmBcvtLCzllQDWVX@hovoldconsulting.com/ > > > ? Have you talked to Bjorn A and Johan? > > > > No, but since grep -r "lm3533_platform_data" * gives 0 results there > > are no platform_data users of lm3533. > > Johan was against driver removal (while it sounds logical due to above) and > referred to some other patches from somebody else. I think you need to > synchronise with the people to have a clear roadmap that all stakeholders > are agree with. With that, the split and other technical issues can be solved > during the normal process. > And this discussion was 2 years ago, and "This device is used in a bunch of Sony phones and Bjorn A posted a series adding devicetree bindings a few years ago" They have had more than enough time, don't you think? You would definitely know if there were any activity since you are IIO reviewer and would be included, were there any activity? > -- > With Best Regards, > Andy Shevchenko > > ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support 2026-05-17 10:34 ` Svyatoslav Ryhel @ 2026-05-17 10:40 ` Andy Shevchenko 2026-05-17 10:44 ` Svyatoslav Ryhel 0 siblings, 1 reply; 18+ messages in thread From: Andy Shevchenko @ 2026-05-17 10:40 UTC (permalink / raw) To: Svyatoslav Ryhel Cc: Lee Jones, Daniel Thompson, Jingoo Han, Pavel Machek, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko, Helge Deller, dri-devel, linux-leds, devicetree, linux-kernel, linux-iio, linux-fbdev On Sun, May 17, 2026 at 01:34:32PM +0300, Svyatoslav Ryhel wrote: > нд, 17 трав. 2026 р. о 13:20 Andy Shevchenko <andriy.shevchenko@intel.com> пише: > > On Sun, May 17, 2026 at 01:13:22PM +0300, Svyatoslav Ryhel wrote: > > > нд, 17 трав. 2026 р. о 10:59 Andy Shevchenko <andriy.shevchenko@intel.com> пише: > > > > On Sun, May 17, 2026 at 10:43:00AM +0300, Svyatoslav Ryhel wrote: > > > > > Convert LM3533 to OF bindings, add missing VIN supply, add support for > > > > > setting mapping mode and LED sources based on device tree. > > > > > > > > How is this being different to > > > > https://lore.kernel.org/lkml/20250218132702.114669-1-clamor95@gmail.com/ > > > > ? > > > > > > I have decided to have a fresh look, this is continuation. > > > > Then it should be something like v4? > > That was more than a year ago, lets start fresh. Those patches are > gone, though I did add many of suggestions from there. > > > > > What about this comment > > > > https://lore.kernel.org/lkml/ZmBcvtLCzllQDWVX@hovoldconsulting.com/ > > > > ? Have you talked to Bjorn A and Johan? > > > > > > No, but since grep -r "lm3533_platform_data" * gives 0 results there > > > are no platform_data users of lm3533. > > > > Johan was against driver removal (while it sounds logical due to above) and > > referred to some other patches from somebody else. I think you need to > > synchronise with the people to have a clear roadmap that all stakeholders > > are agree with. With that, the split and other technical issues can be solved > > during the normal process. > > And this discussion was 2 years ago, and > > "This device is used in a bunch of Sony phones and Bjorn A posted a > series adding devicetree bindings a few years ago" > > They have had more than enough time, don't you think? You would > definitely know if there were any activity since you are IIO reviewer > and would be included, were there any activity? At least it's polite to Cc them your version. -- With Best Regards, Andy Shevchenko ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support 2026-05-17 10:40 ` Andy Shevchenko @ 2026-05-17 10:44 ` Svyatoslav Ryhel 0 siblings, 0 replies; 18+ messages in thread From: Svyatoslav Ryhel @ 2026-05-17 10:44 UTC (permalink / raw) To: Andy Shevchenko Cc: Lee Jones, Daniel Thompson, Jingoo Han, Pavel Machek, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko, Helge Deller, dri-devel, linux-leds, devicetree, linux-kernel, linux-iio, linux-fbdev, johan нд, 17 трав. 2026 р. о 13:40 Andy Shevchenko <andriy.shevchenko@intel.com> пише: > > On Sun, May 17, 2026 at 01:34:32PM +0300, Svyatoslav Ryhel wrote: > > нд, 17 трав. 2026 р. о 13:20 Andy Shevchenko <andriy.shevchenko@intel.com> пише: > > > On Sun, May 17, 2026 at 01:13:22PM +0300, Svyatoslav Ryhel wrote: > > > > нд, 17 трав. 2026 р. о 10:59 Andy Shevchenko <andriy.shevchenko@intel.com> пише: > > > > > On Sun, May 17, 2026 at 10:43:00AM +0300, Svyatoslav Ryhel wrote: > > > > > > Convert LM3533 to OF bindings, add missing VIN supply, add support for > > > > > > setting mapping mode and LED sources based on device tree. > > > > > > > > > > How is this being different to > > > > > https://lore.kernel.org/lkml/20250218132702.114669-1-clamor95@gmail.com/ > > > > > ? > > > > > > > > I have decided to have a fresh look, this is continuation. > > > > > > Then it should be something like v4? > > > > That was more than a year ago, lets start fresh. Those patches are > > gone, though I did add many of suggestions from there. > > > > > > > What about this comment > > > > > https://lore.kernel.org/lkml/ZmBcvtLCzllQDWVX@hovoldconsulting.com/ > > > > > ? Have you talked to Bjorn A and Johan? > > > > > > > > No, but since grep -r "lm3533_platform_data" * gives 0 results there > > > > are no platform_data users of lm3533. > > > > > > Johan was against driver removal (while it sounds logical due to above) and > > > referred to some other patches from somebody else. I think you need to > > > synchronise with the people to have a clear roadmap that all stakeholders > > > are agree with. With that, the split and other technical issues can be solved > > > during the normal process. > > > > And this discussion was 2 years ago, and > > > > "This device is used in a bunch of Sony phones and Bjorn A posted a > > series adding devicetree bindings a few years ago" > > > > They have had more than enough time, don't you think? You would > > definitely know if there were any activity since you are IIO reviewer > > and would be included, were there any activity? > > At least it's polite to Cc them your version. > I assume yes, I have added Johan but there is no email for Bjorn A. > -- > With Best Regards, > Andy Shevchenko > > ^ permalink raw reply [flat|nested] 18+ messages in thread
end of thread, other threads:[~2026-05-17 14:27 UTC | newest] Thread overview: 18+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2026-05-17 7:43 [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support Svyatoslav Ryhel 2026-05-17 7:43 ` [PATCH v1 1/6] dt-bindings: leds: Document TI LM3533 LED controller Svyatoslav Ryhel 2026-05-17 13:44 ` Jonathan Cameron 2026-05-17 14:26 ` Svyatoslav Ryhel 2026-05-17 7:43 ` [PATCH v1 2/6] mfd: lm3533: Convert to use OF bindings Svyatoslav Ryhel 2026-05-17 7:55 ` Andy Shevchenko 2026-05-17 10:11 ` Svyatoslav Ryhel 2026-05-17 11:10 ` Svyatoslav Ryhel 2026-05-17 7:43 ` [PATCH v1 3/6] mfd: lm3533: Add support for VIN power supply Svyatoslav Ryhel 2026-05-17 7:43 ` [PATCH v1 4/6] mfd: lm3533: set DMA mask Svyatoslav Ryhel 2026-05-17 7:43 ` [PATCH v1 5/6] video: backlight: lm3533_bl: Set initial mapping mode from DT Svyatoslav Ryhel 2026-05-17 7:43 ` [PATCH v1 6/6] video: leds: backlight: lm3533: Support getting LED sources " Svyatoslav Ryhel 2026-05-17 7:59 ` [PATCH v1 0/6] mfd: lm3533: convert to OF bindings, improve support Andy Shevchenko 2026-05-17 10:13 ` Svyatoslav Ryhel 2026-05-17 10:20 ` Andy Shevchenko 2026-05-17 10:34 ` Svyatoslav Ryhel 2026-05-17 10:40 ` Andy Shevchenko 2026-05-17 10:44 ` Svyatoslav Ryhel
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox