[PATCH v7 04/10] misc: amd-sbi: Use regmap subsystem

[Akshay Gupta <akshay.gupta@amd.com>]

- regmap subsystem provides multiple benefits over direct smbus APIs
- subsystem adds another abstraction layer on top of struct i2c_client to
  make it easy to read or write registers.
- The subsystem can be helpful in following cases
  - Different types of bus (i2c/i3c), we have plans to support i3c.
  - Different Register address size (1byte/2byte)

Reviewed-by: Naveen Krishna Chatradhi <naveenkrishna.chatradhi@amd.com>
Signed-off-by: Akshay Gupta <akshay.gupta@amd.com>
---
Changes since v4:
- Previously patch 2
Changes since v1:
- Previously patch 3
- Remove "__packed" from data structure

 drivers/misc/amd-sbi/rmi-core.c | 29 ++++++++++++-----------------
 drivers/misc/amd-sbi/rmi-core.h |  3 ++-
 drivers/misc/amd-sbi/rmi-i2c.c  | 25 ++++++++++++++++---------
 3 files changed, 30 insertions(+), 27 deletions(-)

diff --git a/drivers/misc/amd-sbi/rmi-core.c b/drivers/misc/amd-sbi/rmi-core.c
index 74456756270c..663ab9176d95 100644
--- a/drivers/misc/amd-sbi/rmi-core.c
+++ b/drivers/misc/amd-sbi/rmi-core.c
@@ -9,6 +9,7 @@
 #include <linux/err.h>
 #include <linux/i2c.h>
 #include <linux/mutex.h>
+#include <linux/regmap.h>
 #include "rmi-core.h"
 
 /* Mask for Status Register bit[1] */
@@ -21,6 +22,7 @@
 int rmi_mailbox_xfer(struct sbrmi_data *data,
 		     struct sbrmi_mailbox_msg *msg)
 {
+	unsigned int bytes;
 	int i, ret, retry = 10;
 	int sw_status;
 	u8 byte;
@@ -28,14 +30,12 @@ int rmi_mailbox_xfer(struct sbrmi_data *data,
 	mutex_lock(&data->lock);
 
 	/* Indicate firmware a command is to be serviced */
-	ret = i2c_smbus_write_byte_data(data->client,
-					SBRMI_INBNDMSG7, START_CMD);
+	ret = regmap_write(data->regmap, SBRMI_INBNDMSG7, START_CMD);
 	if (ret < 0)
 		goto exit_unlock;
 
 	/* Write the command to SBRMI::InBndMsg_inst0 */
-	ret = i2c_smbus_write_byte_data(data->client,
-					SBRMI_INBNDMSG0, msg->cmd);
+	ret = regmap_write(data->regmap, SBRMI_INBNDMSG0, msg->cmd);
 	if (ret < 0)
 		goto exit_unlock;
 
@@ -46,8 +46,7 @@ int rmi_mailbox_xfer(struct sbrmi_data *data,
 	 */
 	for (i = 0; i < 4; i++) {
 		byte = (msg->data_in >> i * 8) & 0xff;
-		ret = i2c_smbus_write_byte_data(data->client,
-						SBRMI_INBNDMSG1 + i, byte);
+		ret = regmap_write(data->regmap, SBRMI_INBNDMSG1 + i, byte);
 		if (ret < 0)
 			goto exit_unlock;
 	}
@@ -56,8 +55,7 @@ int rmi_mailbox_xfer(struct sbrmi_data *data,
 	 * Write 0x01 to SBRMI::SoftwareInterrupt to notify firmware to
 	 * perform the requested read or write command
 	 */
-	ret = i2c_smbus_write_byte_data(data->client,
-					SBRMI_SW_INTERRUPT, TRIGGER_MAILBOX);
+	ret = regmap_write(data->regmap, SBRMI_SW_INTERRUPT, TRIGGER_MAILBOX);
 	if (ret < 0)
 		goto exit_unlock;
 
@@ -67,8 +65,7 @@ int rmi_mailbox_xfer(struct sbrmi_data *data,
 	 * of the requested command
 	 */
 	do {
-		sw_status = i2c_smbus_read_byte_data(data->client,
-						     SBRMI_STATUS);
+		ret = regmap_read(data->regmap, SBRMI_STATUS, &sw_status);
 		if (sw_status < 0) {
 			ret = sw_status;
 			goto exit_unlock;
@@ -79,8 +76,6 @@ int rmi_mailbox_xfer(struct sbrmi_data *data,
 	} while (retry--);
 
 	if (retry < 0) {
-		dev_err(&data->client->dev,
-			"Firmware fail to indicate command completion\n");
 		ret = -EIO;
 		goto exit_unlock;
 	}
@@ -92,11 +87,11 @@ int rmi_mailbox_xfer(struct sbrmi_data *data,
 	 */
 	if (msg->read) {
 		for (i = 0; i < 4; i++) {
-			ret = i2c_smbus_read_byte_data(data->client,
-						       SBRMI_OUTBNDMSG1 + i);
+			ret = regmap_read(data->regmap,
+					  SBRMI_OUTBNDMSG1 + i, &bytes);
 			if (ret < 0)
 				goto exit_unlock;
-			msg->data_out |= ret << i * 8;
+			msg->data_out |= bytes << i * 8;
 		}
 	}
 
@@ -104,8 +99,8 @@ int rmi_mailbox_xfer(struct sbrmi_data *data,
 	 * BMC must write 1'b1 to SBRMI::Status[SwAlertSts] to clear the
 	 * ALERT to initiator
 	 */
-	ret = i2c_smbus_write_byte_data(data->client, SBRMI_STATUS,
-					sw_status | SW_ALERT_MASK);
+	ret = regmap_write(data->regmap, SBRMI_STATUS,
+			   sw_status | SW_ALERT_MASK);
 
 exit_unlock:
 	mutex_unlock(&data->lock);
diff --git a/drivers/misc/amd-sbi/rmi-core.h b/drivers/misc/amd-sbi/rmi-core.h
index 27165d3bb20f..bbb6bb1cefde 100644
--- a/drivers/misc/amd-sbi/rmi-core.h
+++ b/drivers/misc/amd-sbi/rmi-core.h
@@ -9,6 +9,7 @@
 #include <linux/mutex.h>
 #include <linux/i2c.h>
 #include <linux/platform_device.h>
+#include <linux/regmap.h>
 
 /* SB-RMI registers */
 enum sbrmi_reg {
@@ -47,7 +48,7 @@ enum sbrmi_msg_id {
 
 /* Each client has this additional data */
 struct sbrmi_data {
-	struct i2c_client *client;
+	struct regmap *regmap;
 	struct mutex lock;
 	u32 pwr_limit_max;
 };
diff --git a/drivers/misc/amd-sbi/rmi-i2c.c b/drivers/misc/amd-sbi/rmi-i2c.c
index 9ad4c8093399..7a9801273a4c 100644
--- a/drivers/misc/amd-sbi/rmi-i2c.c
+++ b/drivers/misc/amd-sbi/rmi-i2c.c
@@ -13,24 +13,24 @@
 #include <linux/module.h>
 #include <linux/mutex.h>
 #include <linux/of.h>
+#include <linux/regmap.h>
 #include "rmi-core.h"
 
-static int sbrmi_enable_alert(struct i2c_client *client)
+static int sbrmi_enable_alert(struct sbrmi_data *data)
 {
-	int ctrl;
+	int ctrl, ret;
 
 	/*
 	 * Enable the SB-RMI Software alert status
 	 * by writing 0 to bit 4 of Control register(0x1)
 	 */
-	ctrl = i2c_smbus_read_byte_data(client, SBRMI_CTRL);
-	if (ctrl < 0)
-		return ctrl;
+	ret = regmap_read(data->regmap, SBRMI_CTRL, &ctrl);
+	if (ret < 0)
+		return ret;
 
 	if (ctrl & 0x10) {
 		ctrl &= ~0x10;
-		return i2c_smbus_write_byte_data(client,
-						 SBRMI_CTRL, ctrl);
+		return regmap_write(data->regmap, SBRMI_CTRL, ctrl);
 	}
 
 	return 0;
@@ -55,17 +55,24 @@ static int sbrmi_i2c_probe(struct i2c_client *client)
 {
 	struct device *dev = &client->dev;
 	struct sbrmi_data *data;
+	struct regmap_config sbrmi_i2c_regmap_config = {
+		.reg_bits = 8,
+		.val_bits = 8,
+	};
 	int ret;
 
 	data = devm_kzalloc(dev, sizeof(struct sbrmi_data), GFP_KERNEL);
 	if (!data)
 		return -ENOMEM;
 
-	data->client = client;
 	mutex_init(&data->lock);
 
+	data->regmap = devm_regmap_init_i2c(client, &sbrmi_i2c_regmap_config);
+	if (IS_ERR(data->regmap))
+		return PTR_ERR(data->regmap);
+
 	/* Enable alert for SB-RMI sequence */
-	ret = sbrmi_enable_alert(client);
+	ret = sbrmi_enable_alert(data);
 	if (ret < 0)
 		return ret;
 
-- 
2.25.1