Linux I2C development
 help / color / mirror / Atom feed
From: Wolfram Sang <wsa+renesas@sang-engineering.com>
To: Jie Li <lj29312931@gmail.com>, Linus Walleij <linusw@kernel.org>
Cc: wsa@kernel.org, linux-i2c@vger.kernel.org,
	linux-gpio@vger.kernel.org, linux-kernel@vger.kernel.org,
	Jie Li <jie.i.li@nokia.com>
Subject: Re: [PATCH v4 2/2] i2c: core: support recovery for single-ended GPIOs
Date: Sat, 9 May 2026 12:10:15 +0200	[thread overview]
Message-ID: <af8IB46ST70lXVsk@shikoro> (raw)
In-Reply-To: <20260509091208.18346-3-jie.i.li@nokia.com>

[-- Attachment #1: Type: text/plain, Size: 1399 bytes --]

On Sat, May 09, 2026 at 11:12:08AM +0200, Jie Li wrote:
> Currently, i2c_init_recovery() only assigns the set_sda/set_scl
> hooks if gpiod_get_direction() returns GPIO_LINE_DIRECTION_OUT.
> 
> This logic fails on certain SoC controllers where open-drain lines
> in a high-impedance state are physically reported as inputs. This
> leads to a "deadlock" where the I2C core refuses to assign the
> recovery hooks because it incorrectly assumes the pins are
> input-only, even though they are fully capable of driving the bus
> low for recovery.
> 
> Update the recovery initialization to use the new
> gpiod_is_single_ended() helper. If a GPIO is configured as
> open-drain or open-source in the firmware, it is safe to assume
> it can be used for bus recovery, even if the current hardware
> direction is reported as input.
> 
> Signed-off-by: Jie Li <jie.i.li@nokia.com>
> Reviewed-by: Linus Walleij <linusw@kernel.org>
> Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

I overlooked that the change with GPIO_LINE_DIRECTION_OUT I suggested
for this patch is at the same location as commit[1]. I already pushed
out said commit for -rc3 and it is, thus, already in -next, too. No big
harm, but there will be a little conflict when applying. Sorry, Linus!

[1] b47bc7c022dd ("i2c: Compare the return value of gpiod_get_direction against GPIO_LINE_DIRECTION_OUT")


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

  reply	other threads:[~2026-05-09 10:10 UTC|newest]

Thread overview: 22+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-01-14 14:13 [PATCH v1 0/2] i2c: add support for forced SDA recovery Jie Li
2026-01-14 14:13 ` [PATCH v1 1/2] i2c: core: add "force-set-sda" flag for open-drain SDA without "FLAG_IS_OUT" bit Jie Li
2026-01-14 14:13 ` [PATCH v1 2/2] dt-bindings: i2c: add force-set-sda property Jie Li
2026-01-16 14:14   ` Krzysztof Kozlowski
2026-01-15  9:27 ` [PATCH v1 0/2] i2c: add support for forced SDA recovery Linus Walleij
2026-01-15 13:12   ` 李杰
2026-01-16 13:59     ` Linus Walleij
2026-01-25 19:51       ` [PATCH v2 0/2] i2c: improve bus recovery for single-ended GPIOs Jie Li
2026-01-25 19:51         ` [PATCH v2 1/2] gpiolib: add gpiod_is_single_ended() helper Jie Li
2026-01-27  9:46           ` Linus Walleij
2026-01-25 19:51         ` [PATCH v2 2/2] i2c: core: support recovery for single-ended GPIOs Jie Li
2026-01-27  9:47           ` Linus Walleij
2026-02-01 11:18             ` [PATCH v3 0/2] i2c: improve bus " Jie Li
2026-02-01 11:18               ` [PATCH v3 1/2] gpiolib: add gpiod_is_single_ended() helper Jie Li
2026-02-01 11:18               ` [PATCH v3 2/2] i2c: core: support recovery for single-ended GPIOs Jie Li
2026-05-04 12:14                 ` Wolfram Sang
2026-05-09  9:12                   ` [PATCH v4 0/2] i2c: improve bus " Jie Li
2026-05-09  9:12                     ` [PATCH v4 1/2] gpiolib: add gpiod_is_single_ended() helper Jie Li
2026-05-09  9:12                     ` [PATCH v4 2/2] i2c: core: support recovery for single-ended GPIOs Jie Li
2026-05-09 10:10                       ` Wolfram Sang [this message]
2026-05-11  7:25                         ` 李杰
2026-04-22 18:47               ` [PATCH v3 0/2] i2c: improve bus " 李杰

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=af8IB46ST70lXVsk@shikoro \
    --to=wsa+renesas@sang-engineering.com \
    --cc=jie.i.li@nokia.com \
    --cc=linusw@kernel.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-i2c@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=lj29312931@gmail.com \
    --cc=wsa@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox