From: "Randy.Dunlap" <rddunlap@osdl.org>
To: linux-ia64@vger.kernel.org
Subject: Re: IA64 test report:USB mouse donesn't work : 2.4.26 /Lion
Date: Tue, 25 May 2004 15:02:09 +0000 [thread overview]
Message-ID: <20040525080209.4ef5271a.rddunlap@osdl.org> (raw)
In-Reply-To: <6E0C289723A0564F9A8279E236E8565F0766858F@pdsmsx402.pd.intel.com>
On Tue, 25 May 2004 20:07:12 +0800 Yu, Luming wrote:
|
| After executing kudzu, and removing the PS/2 mouse configuration, the
| USB mouse works pretty well.(I'm sorry for I diden't notice this point
| beofre.)
| So this issue is gone.
|
| The interesting thing is that PS/2 and USB mouse can work together
| under 2.6. But 2.4 cannot.
Interesting in what way? or do you mean on this particular platform?
In general, it's expected that PS/2 and USB mice can and do work
together, in 2.6 and 2.4.
| Thanks,
| Luming
|
| >-----Original Message-----
| >From: linux-ia64-owner@vger.kernel.org
| >[mailto:linux-ia64-owner@vger.kernel.org] On Behalf Of Wang, Zhenyu Z
| >Sent: Thursday, May 13, 2004 4:05 PM
| >To: linux-ia64@vger.kernel.org; Brown, Len
| >Cc: linux-acpi
| >Subject: IA64 test report:USB mouse donesn't work : 2.4.26
| >/Lion 2004-5-12: 9/10 pass
| >
| >ACPI Test Report for 2.4 ia64 kernel + latest ACPI
| > ============| > Hardware Configuration:
| > -----------------------
| > System Name: ACPI-LION
| > System Type: 4 way 800M Itanium, Lion
| > M/B revision: N/A
| > Processor version: N/A
| > Firmware Versions: N/A
| > I/O configuration summary:
| > QLogic QLA12160, Seagate ST39205LC boot drive
| > IDE floppy and CDROM
| > Serial console
| > PS/2 keyboard and mouse
| > USB mouse
| > Ethernet Pro 100
| >
| > Software Configuration:
| > -----------------------
| > 1.Bk pull form lia64.bkbits.net/linux-ia64-2.4 on 4/28
| >(Shanghai time)
| > 2.Bk pull from
| >linux-acpi.bkbits.net/linux-acpi-test-2.4.26 on 4/28 (Shanghai time)
| >
| > ACPI Features Tested: (prioritized).
| > --------------------
| > 1. Boot off SCSI disk tested ok
| > 2. PS/2 keyboard tested ok
| > 3. ATI (run X window system) tested ok
| > 4. PS/2 mouse tested ok
| > 5. USB mouse Doesn't work (Both
| >CONFIG_USB_UHCI_ALT and CONFIG_USB_UHCI failed)
| > 6. NIC (eg. Ping or ftp) tested ok
| > 7. IDE (eg. r/w floppy or CDROM) tested ok
| > 8. SCI (eg. Press power button) tested ok
| > 9. Soft Power off tested ok
| > 10. serial console tested ok
| >
| >Linux version 2.4.26 (root@acpi-lion) (gcc version 3.2) #3 SMP Wed May
| >12 22:39:29 CST 2004
| >EFI v1.02 by INTEL: SALsystab=0x5ff26170 ACPI=0x5fe963e8 ACPI
| >2.0=0x5fe96630 MPS=0x5ffd0000 SMBIOS=0xf00a0
| >ACPI: RSDP (v002 INTEL ) @
| >0x000000005fe96630
| >ACPI: XSDT (v001 INTEL SR460AC 0x00000003 MSFT 0x0100000a) @
| >0x000000005fe96658
| >ACPI: FADT (v003 INTEL SR460AC 0x00000006 MSFT 0x0100000a) @
| >0x000000005fe96700
| >ACPI: MADT (v001 INTEL SR460AC 0x0000000a MSFT 0x0100000a) @
| >0x000000005fe96838
| >ACPI: DSDT (v001 INTEL SR460AC4 0x00000006 MSFT 0x0100000a) @
| >0x0000000000000000
| >efi.trim_top: ignoring 4KB of memory at 0x0 due to granule hole at 0x0
| >efi.trim_top: ignoring 448KB of memory at 0x1000 due to granule hole at
| >0x0
| >efi.trim_top: ignoring 4KB of memory at 0x71000 due to granule hole at
| >0x0
| >efi.trim_top: ignoring 8KB of memory at 0x72000 due to granule hole at
| >0x0
| >efi.trim_top: ignoring 100KB of memory at 0x87000 due to
| >granule hole at
| >0x0
| >efi.trim_bottom: ignoring 15360KB of memory at 0x100000 due to granule
| >hole at 0x0
| >SAL v3.00: oem=INTEL MSL REF SAL , product| >SAL: entry: pal_proc=0x5ff48010, sal_proc=0x5feb53e0
| >SAL: Platform features BusLock IRQ_Redirection
| >SAL: AP wakeup using external interrupt vector 0xf0
| >booting generic kernel on platform dig
| >CPU 0: 51 virtual and 44 physical address bits
| >iosapic_system_init: Disabling PC-AT compatible 8259 interrupts
| >ACPI: Local APIC address 0xc0000000fee00000
| >ACPI: LSAPIC (acpi_id[0x00] lsapic_id[0x00] lsapic_eid[0x00] enabled)
| >CPU 0 (0x0000) enabled (BSP)
| >ACPI: LSAPIC (acpi_id[0x01] lsapic_id[0x03] lsapic_eid[0x00] enabled)
| >CPU 1 (0x0300) enabled
| >ACPI: LSAPIC (acpi_id[0x02] lsapic_id[0x01] lsapic_eid[0x00] enabled)
| >CPU 2 (0x0100) enabled
| >ACPI: LSAPIC (acpi_id[0x03] lsapic_id[0x02] lsapic_eid[0x00] enabled)
| >CPU 3 (0x0200) enabled
| >ACPI: LSAPIC (acpi_id[0x04] lsapic_id[0xaa] lsapic_eid[0x00] disabled)
| >CPU 4 (0xaa00) disabled
| >ACPI: LSAPIC (acpi_id[0x05] lsapic_id[0xaa] lsapic_eid[0x00] disabled)
| >CPU 5 (0xaa00) disabled
| >ACPI: LSAPIC (acpi_id[0x06] lsapic_id[0xaa] lsapic_eid[0x00] disabled)
| >CPU 6 (0xaa00) disabled
| >ACPI: LSAPIC (acpi_id[0x07] lsapic_id[0xaa] lsapic_eid[0x00] disabled)
| >CPU 7 (0xaa00) disabled
| >ACPI: IOSAPIC (id[0x4] global_irq_base[0x0] address[00000000fec00000])
| > IOSAPIC v2.1, address 0xfec00000, GSIs 0x0-0x3f
| >ACPI: PLAT_INT_SRC (low edge type[0x1] id[0x0002] eid[0x0]
| >iosapic_vector[0x2] global_irq[0x3d]
| >PLATFORM int 0x1: GSI 0x3d(low,edge) -> CPU 0x0200 vector 2
| >ACPI: PLAT_INT_SRC (low level type[0x3] id[0x0002] eid[0x0]
| >iosapic_vector[0x1e] global_irq[0x3c]
| >PLATFORM int 0x3: GSI 0x3c(low,level) -> CPU 0x0200 vector 30
| >ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
| >register_intr: changing vector 39 from IO-SAPIC-edge to IO-SAPIC-level
| >4 CPUs available, 8 CPUs total
| >On node 0 totalpages: 96473
| >zone(0): 96473 pages.
| >zone(1): 0 pages.
| >zone(2): 0 pages.
| >Building zonelist for node : 0
| >Kernel command line: BOOT_IMAGE=scsi0:\EFI\redhat\vmlinux.24
| >root=/dev/sda2 console=ttyS0,9600n8 console=tty0 ro
| >FPSWA interface at 0x5fb34010, revision 1.12
| >CPU 0: base freq\x133.332MHz, ITC ratio\x12/2, ITC freqy9.996MHz
| >Console: colour VGA+ 80x25
| >Calibrating delay loop... 797.80 BogoMIPS
| >Placing software IO TLB between 0xe000000001848000 - 0xe000000001a48000
| >Memory: 1533024k/1543568k available (5939k code, 10608k reserved, 2890k
| >data, 512k init)
| >Dentry cache hash table entries: 131072 (order: 7, 2097152 bytes)
| >Inode cache hash table entries: 131072 (order: 7, 2097152 bytes)
| >Mount cache hash table entries: 1024 (order: 0, 16384 bytes)
| >Buffer cache hash table entries: 131072 (order: 6, 1048576 bytes)
| >Page-cache hash table entries: 131072 (order: 6, 1048576 bytes)
| >POSIX conformance testing by UNIFIX
| >Boot processor id 0x0/0x0
| >SMP: starting up secondaries.
| >CPU 1: 51 virtual and 44 physical address bits
| >CPU 1: base freq\x133.332MHz, ITC ratio\x12/2, ITC freqy9.996MHz
| >Calibrating delay loop... 797.80 BogoMIPS
| >CPU 1: synchronized ITC with CPU 0 (last diff 0 cycles, maxerr 558
| >cycles)
| >CPU1: CPU has booted.
| >CPU 2: 51 virtual and 44 physical address bits
| >CPU 2: base freq\x133.332MHz, ITC ratio\x12/2, ITC freqy9.996MHz
| >Calibrating delay loop... 797.80 BogoMIPS
| >CPU 2: synchronized ITC with CPU 0 (last diff 0 cycles, maxerr 558
| >cycles)
| >CPU2: CPU has booted.
| >CPU 3: 51 virtual and 44 physical address bits
| >CPU 3: base freq\x133.332MHz, ITC ratio\x12/2, ITC freqy9.996MHz
| >Calibrating delay loop... 797.80 BogoMIPS
| >CPU 3: synchronized ITC with CPU 0 (last diff 0 cycles, maxerr 558
| >cycles)
| >CPU3: CPU has booted.
| >Before bogomips.
| >Total of 4 processors activated (3189.20 BogoMIPS).
| >Waiting on wait_init_idle (map = 0xe)
| >All processors have done init_idle
| >ACPI: Subsystem revision 20040326
| >PCI: Using SAL to access configuration space
| > tbxface-0117 [03] acpi_load_tables : ACPI Tables successfully
| >acquired
| >Parsing all Control
| >Methods:.......................................................
| >.........
| >...............................................................
| >.........
| >......................................
| >Table [DSDT](id F004) - 934 Objects with 101 Devices 174 Methods 19
| >Regions
| >ACPI Namespace successfully loaded at root e000000004c23718
| >evxfevnt-0093 [04] acpi_enable : Transition to ACPI mode
| >successful
| >evgpeblk-0867 [06] ev_create_gpe_block : GPE 00 to 15 [_GPE]
| >2 regs at
| >0000000000000C0C on int 9
| >evgpeblk-0925 [06] ev_create_gpe_block : Found 2 Wake, Enabled 0
| >Runtime GPEs in this block
| >evgpeblk-0867 [06] ev_create_gpe_block : GPE 16 to 31 [_GPE]
| >2 regs at
| >0000000000000C16 on int 9
| >evgpeblk-0925 [06] ev_create_gpe_block : Found 0 Wake, Enabled 1
| >Runtime GPEs in this block
| >Completing Region/Field/Buffer/Package
| >initialization:.....................................................
| >Initialized 19/19 Regions 0/0 Fields 24/24 Buffers 10/12 Packages (943
| >nodes)
| >Executing all Device _STA and_INI
| >methods:.......................................................
| >.........
| >..................................
| >98 Devices found containing: 98 _STA, 7 _INI methods
| >ACPI: Interpreter enabled
| >ACPI: Using IOSAPIC for interrupt routing
| >ACPI: System [ACPI] (supports S0 S4 S5)
| >ACPI: PCI Root Bridge [PCI0] (00:00)
| >alloc 0x0-0xcf7 from PCI IO for PCI Bus 00:00 failed
| >ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
| >ACPI: Power Resource [URP1] (off)
| >ACPI: Power Resource [URP2] (off)
| >ACPI: Power Resource [FDDP] (off)
| >ACPI: Power Resource [LPTP] (off)
| >ACPI: PCI Root Bridge [PCI1] (00:01)
| >ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT]
| >ACPI: PCI Root Bridge [PCI2] (00:04)
| >ACPI: PCI Interrupt Routing Table [\_SB_.PCI2._PRT]
| >ACPI: PCI Root Bridge [PCI3] (00:08)
| >ACPI: PCI Interrupt Routing Table [\_SB_.PCI3._PRT]
| >ACPI: PCI Root Bridge [PCI4] (00:0c)
| >ACPI: PCI Interrupt Routing Table [\_SB_.PCI4._PRT]
| >ACPI: PCI Root Bridge [PCI5] (00:0f)
| >ACPI: PCI Interrupt Routing Table [\_SB_.PCI5._PRT]
| >ACPI: PCI Root Bridge [PCI6] (00:12)
| >ACPI: PCI Interrupt Routing Table [\_SB_.PCI6._PRT]
| >ACPI: PCI Root Bridge [CBN] (00:15)
| >PCI->APIC IRQ transform: (00:03.2 INTD) -> CPU 0x0000 vector 48
| >PCI: no interrupt route for 00:00:03 pin B
| >PCI->APIC IRQ transform: (00:05.0 INTA) -> CPU 0x0000 vector 49
| >PCI->APIC IRQ transform: (00:06.0 INTA) -> CPU 0x0000 vector 50
| >PCI->APIC IRQ transform: (01:02.0 INTA) -> CPU 0x0000 vector 51
| >PCI->APIC IRQ transform: (01:0f.0 INTA) -> CPU 0x0000 vector 52
| >PCI->APIC IRQ transform: (04:0f.0 INTA) -> CPU 0x0000 vector 52
| >PCI->APIC IRQ transform: (08:0f.0 INTA) -> CPU 0x0000 vector 53
| >PCI->APIC IRQ transform: (0c:0f.0 INTA) -> CPU 0x0000 vector 53
| >PCI->APIC IRQ transform: (0f:0f.0 INTA) -> CPU 0x0000 vector 54
| >PCI->APIC IRQ transform: (12:0f.0 INTA) -> CPU 0x0000 vector 54
| >Linux NET4.0 for Linux 2.4
| >Based upon Swansea University Computer Society NET3.039
| >Initializing RT netlink socket
| >PAL Information Facility v0.5
| >EFI Variables Facility v0.06 2002-Dec-10
| >Total HugeTLB memory allocated, 0
| >Starting kswapd
| >Journalled Block Device driver loaded
| >Hugetlbfs mounted.
| >Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
| >ACPI: Power Button (FF) [PWRF]
| >ACPI: Processor [CPU0] (supports C1)
| >ACPI: Processor [CPU1] (supports C1)
| >ACPI: Processor [CPU2] (supports C1)
| >ACPI: Processor [CPU3] (supports C1)
| >pty: 256 Unix98 ptys configured
| >Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
| >DETECT_IRQ SERIAL_PCI SERIAL_ACPI enabled
| >ttyS00 at 0x03f8 (irq = 44) is a 16550A
| >ttyS01 at 0x02f8 (irq = 45) is a 16550A
| >ttyS00 at port 0x03f8 (irq = 44) is a 16550A
| >ttyS01 at port 0x02f8 (irq = 45) is a 16550A
| >EFI Time Services Driver v0.4
| >loop: loaded (max 8 devices)
| >Intel(R) PRO/1000 Network Driver - version 5.2.30.1-k1
| >Copyright (c) 1999-2004 Intel Corporation.
| >eepro100.c:v1.09j-t 9/29/99 Donald Becker
| >http://www.scyld.com/network/eepro100.html
| >eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V.
| >Savochkin
| ><saw@saw.sw.com.sg> and others
| >PCI: Found IRQ 49 for device 00:05.0
| >eth0: Intel Corp. 82557/8/9 [Ethernet Pro 100], 00:D0:B7:F9:F4:F6, IRQ
| >49.
| > Board assembly 727095-004, Physical connectors present: RJ45
| > Primary interface chip i82555 PHY #1.
| > General self-test: passed.
| > Serial sub-system self-test: passed.
| > Internal registers self-test: passed.
| > ROM checksum self-test: passed (0x04f4518b).
| >Linux agpgart interface v0.99 (c) Jeff Hartmann
| >agpgart: Maximum main memory to use for agp memory: 1403M
| >agpgart: no supported devices found.
| >[drm] Initialized r128 2.2.0 20010917 on minor 0
| >[drm] Initialized radeon 1.7.0 20020828 on minor 1
| >Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
| >ide: Assuming 33MHz system bus speed for PIO modes; override with
| >idebus=xx
| >PIIX4: IDE controller at PCI slot 00:03.1
| >PCI: Found IRQ 0 for device 00:03.1
| >PIIX4: chipset revision 1
| >PIIX4: not 100% native mode: will probe irqs later
| > ide0: BM-DMA at 0x1000-0x1007, BIOS settings: hda:pio, hdb:pio
| > ide1: BM-DMA at 0x1008-0x100f, BIOS settings: hdc:DMA, hdd:pio
| >hda: LS-120 S200 01 UHD Floppy, ATAPI FLOPPY drive
| >hdc: CD-224E, ATAPI CD/DVD-ROM drive
| >global_restore_flags: 10084a6010 (e000000004ab2490)
| >ide0 at 0x1f0-0x1f7,0x3f6 on irq 34
| >global_restore_flags: 10084a2010 (e000000004ab2490)
| >ide1 at 0x170-0x177,0x376 on irq 33
| >hdc: attached ide-cdrom driver.
| >hdc: ATAPI 24X CD-ROM drive, 128kB Cache
| >Uniform CD-ROM driver Revision: 3.12
| >hda: attached ide-floppy driver.
| >hda: No disk in drive
| >hda: 123264kB, 963/8/32 CHS, 533 kBps, 512 sector size, 720 rpm
| >SCSI subsystem driver Revision: 1.00
| >PCI: Found IRQ 51 for device 01:02.0
| >qla1280: QLA12160 found on PCI bus 1, dev 2
| >scsi(0): Reading NVRAM
| >scsi(0:0): Resetting SCSI BUS
| >scsi(0:1): Resetting SCSI BUS
| >PCI: Found IRQ 51 for device 01:02.0
| >scsi0 : QLogic QLA12160 PCI to SCSI Host Adapter: bus 1 device 2 irq 51
| > Firmware version: 10.04.32, Driver version 3.23.37
| > Vendor: SEAGATE Model: ST39205LC Rev: 5063
| > Type: Direct-Access ANSI SCSI revision: 03
| >scsi(0:0:0:0): Sync: period 9, offset 24, Wide, DT, Tagged queuing:
| >depth 255
| >scsi1 : SCSI host adapter emulation for IDE ATAPI devices
| >Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
| >SCSI device sda: 17921835 512-byte hdwr sectors (9176 MB)
| >Partition check:
| > sda: sda1 sda2 sda3
| >Fusion MPT base driver 2.05.11.03
| >Copyright (c) 1999-2003 LSI Logic Corporation
| >mptbase: 0 MPT adapters found, 0 installed.
| >Fusion MPT SCSI Host driver 2.05.11.03
| >cs4281: version v1.30.64 time 22:37:08 May 12 2004
| >cs4281: Unable to locate any cs4281 device with valid IDs 0x1013-0x6005
| >usb.c: registered new driver usbdevfs
| >usb.c: registered new driver hub
| >host/usb-uhci.c: $Revision: 1.275 $ time 22:37:51 May 12 2004
| >host/usb-uhci.c: High bandwidth mode enabled
| >PCI: Found IRQ 48 for device 00:03.2
| >host/usb-uhci.c: USB UHCI at I/O 0x6f80, IRQ 48
| >host/usb-uhci.c: Detected 2 ports
| >usb.c: new USB bus registered, assigned bus number 1
| >hub.c: USB hub found
| >hub.c: 2 ports detected
| >host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
| >usb.c: registered new driver hiddev
| >usb.c: registered new driver hid
| >hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
| >hid-core.c: USB HID support drivers
| >Linux video capture interface: v1.00
| >mice: PS/2 mouse device common for all mice
| >NET4: Linux TCP/IP 1.0 for NET4.0
| >IP Protocols: ICMP, UDP, TCP
| >IP: routing cache hash table of 32768 buckets, 512Kbytes
| >TCP: Hash tables configured (established 262144 bind 65536)
| >NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
| >EXT3-fs: INFO: recovery required on readonly filesystem.
| >EXT3-fs: write access will be enabled during recovery.
| >hub.c: new USB device 00:03.2-2, assigned address 2
| >host/usb-uhci.c: interrupt, status 2, frame# 1236
| >input: USB HID v1.00 Mouse [413c:3010] on usb1:2.0
| >(recovery.c, 256): journal_recover: JBD: recovery, exit status 0,
| >recovered transactions 675565 to 675973
| >(recovery.c, 258): journal_recover: JBD: Replayed 2841 and revoked 7/12
| >blocks
| >kjournald starting. Commit interval 5 seconds
| >EXT3-fs: recovery complete.
| >EXT3-fs: mounted filesystem with ordered data mode.
| >VFS: Mounted root (ext3 filesystem) readonly.
| >Freeing unused kernel memory: 512kB freed
| >EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
| >Adding Swap: 2040208k swap-space (priority -1)
| >ide-floppy: hda: I/O error, pc = 0, key = 2, asc = 3a, ascq = 0
| >usb.c: USB disconnect on device 00:03.2-2 address 2
| >ide-floppy: hda: I/O error, pc = 1b, key = 2, asc = 3a, ascq = 0
| >hda: No disk in drive
| >hub.c: new USB device 00:03.2-1, assigned address 3
| >host/usb-uhci.c: interrupt, status 2, frame# 792
| >input: USB HID v1.00 Mouse [413c:3010] on usb1:3.0
| >ide-floppy: hda: I/O error, pc = 0, key = 2, asc = 3a, ascq = 0
| >ide-floppy: hda: I/O error, pc = 1b, key = 2, asc = 3a, ascq = 0
| >hda: No disk in drive
| >usb.c: USB disconnect on device 00:03.2-1 address 3
| >hub.c: new USB device 00:03.2-2, assigned address 4
| >host/usb-uhci.c: interrupt, status 2, frame# 1899
| >input: USB HID v1.00 Mouse [413c:3010] on usb1:4.0
| >ide-floppy: hda: I/O error, pc = 0, key = 2, asc = 3a, ascq = 0
| >ide-floppy: hda: I/O error, pc = 1b, key = 2, asc = 3a, ascq = 0
| >hda: No disk in drive
| >ide-floppy: hda: I/O error, pc = 0, key = 2, asc = 3a, ascq = 0
| >ide-floppy: hda: I/O error, pc = 1b, key = 2, asc = 3a, ascq = 0
| >hda: No disk in drive
| >ide-floppy: hda: I/O error, pc = 0, key = 2, asc = 3a, ascq = 0
| >ide-floppy: hda: I/O error, pc = 1b, key = 2, asc = 3a, ascq = 0
| >hda: No disk in drive
| >hda: 1440kB, 2880 blocks, 512 sector size
| >hda: 1440kB, 80/2/18 CHS, 150 kBps, 512 sector size, 720 rpm
| > hda:
| > hda:
| > hda:
| > hda:
| > hda:
| >
| > CPU0 CPU1 CPU2 CPU3
| > 32: 2159 0 12 6 IO-SAPIC-edge
| >keyboard
| > 33: 988 2 30 6 IO-SAPIC-edge ide1
| > 34: 319 11 13 2 IO-SAPIC-edge ide0
| > 39: 0 0 0 0 IO-SAPIC-level acpi
| > 44: 5431 0 11 0
| >IO-SAPIC-edge serial
| > 45: 17 0 0 0
| >IO-SAPIC-edge serial
| > 48: 33 0 0 0 IO-SAPIC-level
| >usb-uhci
| > 49: 2413 9 60 16 IO-SAPIC-level eth0
| > 51: 7216 8 343 65 IO-SAPIC-level
| >qla1280
| >239: 1350648 1349963 1349429 1340144 LSAPIC timer
| >254: 58 18 55 37 LSAPIC IPI
| >NMI: 0 0 0 0
| >ERR: 0
| >
| >00:03.0 ISA bridge: Intel Corp. 82372FB PIIX5 ISA (rev 01)
| > Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
| >ParErr- Stepping- SERR+ FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Latency: 0
| >
| >00:03.1 IDE interface: Intel Corp. 82372FB PIIX5 IDE (rev 01) (prog-if
| >80 [Master])
| > Subsystem: Intel Corp.: Unknown device 414c
| > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Latency: 64
| > Region 4: I/O ports at 1000 [size\x16]
| >
| >00:03.2 USB Controller: Intel Corp. 82372FB PIIX5 USB (rev 01) (prog-if
| >00 [UHCI])
| > Subsystem: Intel Corp.: Unknown device 414c
| > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Latency: 64
| > Interrupt: pin D routed to IRQ 48
| > Region 4: I/O ports at 6f80 [size2]
| >
| >00:03.3 SMBus: Intel Corp. 82372FB PIIX5 SMBus (rev 01)
| > Subsystem: Intel Corp.: Unknown device 414c
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Interrupt: pin B routed to IRQ 0
| > Region 4: I/O ports at c000 [disabled] [size\x16]
| >
| >00:04.0 PIC: Intel Corp. 683053 Programmable Interrupt Device (rev 01)
| >(prog-if 20 [IO(X)-APIC])
| > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
| >ParErr+ Stepping- SERR+ FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Latency: 0 (2000ns min, 2000ns max)
| >
| >00:05.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100]
| >(rev 08)
| > Subsystem: Intel Corp. 82559 Fast Ethernet LAN on Motherboard
| > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
| >ParErr+ Stepping- SERR+ FastB2B-
| > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Latency: 64 (2000ns min, 14000ns max), cache line size 10
| > Interrupt: pin A routed to IRQ 49
| > Region 0: Memory at 00000000fafe0000 (32-bit, non-prefetchable)
| >[size=4K]
| > Region 1: I/O ports at 6f00 [sized]
| > Region 2: Memory at 00000000fae00000 (32-bit, non-prefetchable)
| >[size=1M]
| > Capabilities: [dc] Power Management version 2
| > Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
| >PME(D0+,D1+,D2+,D3hot+,D3cold+)
| > Status: D0 PME-Enable- DSel=0 DScale=2 PME-
| >
| >00:06.0 VGA compatible controller: ATI Technologies Inc Rage
| >XL (rev 27)
| >(prog-if 00 [VGA])
| > Subsystem: Intel Corp.: Unknown device 414c
| > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping+ SERR- FastB2B-
| > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Latency: 64 (2000ns min), cache line size 10
| > Interrupt: pin A routed to IRQ 50
| > Region 0: Memory at 00000000fb000000 (32-bit, non-prefetchable)
| >[size\x16M]
| > Region 1: I/O ports at 6800 [size%6]
| > Region 2: Memory at 00000000faff0000 (32-bit, non-prefetchable)
| >[size=4K]
| > Expansion ROM at 00000000fafc0000 [disabled] [size\x128K]
| > Capabilities: [5c] Power Management version 2
| > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
| >PME(D0-,D1-,D2-,D3hot-,D3cold-)
| > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
| >
| >00:10.0 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >01:02.0 SCSI storage controller: QLogic Corp. ISP12160 Dual Channel
| >Ultra3 SCSI Processor (rev 06)
| > Subsystem: QLogic Corp.: Unknown device 0007
| > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
| >ParErr+ Stepping- SERR+ FastB2B-
| > Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Latency: 64 (16000ns min), cache line size 10
| > Interrupt: pin A routed to IRQ 51
| > Region 0: I/O ports at 8800 [size%6]
| > Region 1: Memory at 00000000f1ff0000 (32-bit, non-prefetchable)
| >[size=4K]
| > Expansion ROM at 00000000f1fc0000 [disabled] [size\x128K]
| > Capabilities: [44] Power Management version 1
| > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
| >PME(D0-,D1-,D2-,D3hot-,D3cold-)
| > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
| >
| >01:0f.0 PCI Hot-plug controller: Intel Corp. 82466GX
| >Integrated Hot-Plug
| >Controller (IHPC) (rev 01)
| > Subsystem: Intel Corp.: Unknown device 012b
| > Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr+ Stepping- SERR+ FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Interrupt: pin A routed to IRQ 52
| > Region 0: Memory at 00000000f1fe0000 (32-bit, non-prefetchable)
| >[size%6]
| >
| >04:0f.0 PCI Hot-plug controller: Intel Corp. 82466GX
| >Integrated Hot-Plug
| >Controller (IHPC) (rev 01)
| > Subsystem: Intel Corp.: Unknown device 012b
| > Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr+ Stepping- SERR+ FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Interrupt: pin A routed to IRQ 52
| > Region 0: Memory at 00000000e7ff0000 (32-bit, non-prefetchable)
| >[size%6]
| >
| >08:0f.0 PCI Hot-plug controller: Intel Corp. 82466GX
| >Integrated Hot-Plug
| >Controller (IHPC) (rev 01)
| > Subsystem: Intel Corp.: Unknown device 012b
| > Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr+ Stepping- SERR+ FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Interrupt: pin A routed to IRQ 53
| > Region 0: Memory at 00000000ddff0000 (32-bit, non-prefetchable)
| >[size%6]
| >
| >0c:0f.0 PCI Hot-plug controller: Intel Corp. 82466GX
| >Integrated Hot-Plug
| >Controller (IHPC) (rev 01)
| > Subsystem: Intel Corp.: Unknown device 012b
| > Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr+ Stepping- SERR+ FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Interrupt: pin A routed to IRQ 53
| > Region 0: Memory at 00000000d5ff0000 (32-bit, non-prefetchable)
| >[size%6]
| >
| >0f:0f.0 PCI Hot-plug controller: Intel Corp. 82466GX
| >Integrated Hot-Plug
| >Controller (IHPC) (rev 01)
| > Subsystem: Intel Corp.: Unknown device 012b
| > Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr+ Stepping- SERR+ FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Interrupt: pin A routed to IRQ 54
| > Region 0: Memory at 00000000cdff0000 (32-bit, non-prefetchable)
| >[size%6]
| >
| >12:0f.0 PCI Hot-plug controller: Intel Corp. 82466GX
| >Integrated Hot-Plug
| >Controller (IHPC) (rev 01)
| > Subsystem: Intel Corp.: Unknown device 012b
| > Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr+ Stepping- SERR+ FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Interrupt: pin A routed to IRQ 54
| > Region 0: Memory at 00000000c5ff0000 (32-bit, non-prefetchable)
| >[size%6]
| >
| >15:00.0 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:00.1 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:00.2 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:00.3 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:00.4 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:00.5 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:00.6 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:00.7 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:01.0 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:01.1 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:01.2 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:01.3 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:01.4 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:01.5 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:01.6 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:01.7 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:04.0 Host bridge: Intel Corp. 460GX - 84460GX System Data Controller
| >(SDC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Data Controller
| >(SDC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:10.0 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:10.1 Host bridge: Intel Corp. 450NX - 82454NX/84460GX PCI Expander
| >Bridge (rev 05)
| > Subsystem: Intel Corp. 450NX - 82454NX/84460GX PCI Expander
| >Bridge
| > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
| >ParErr+ Stepping- SERR+ FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort+ >SERR- <PERR-
| > Latency: 128, cache line size 10
| >
| >15:11.0 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:12.0 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:12.1 Host bridge: Intel Corp. 460GX - 82466GX Wide and fast PCI
| >eXpander Bridge (WXB) (rev 07)
| > Subsystem: Intel Corp. 460GX - 82466GX Wide and fast PCI
| >eXpander Bridge (WXB)
| > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
| >ParErr+ Stepping- SERR+ FastB2B-
| > Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Latency: 32, cache line size 10
| > Capabilities: [90] Power Management version 2
| > Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
| >PME(D0-,D1-,D2-,D3hot-,D3cold-)
| > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
| >
| >15:13.0 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:13.1 Host bridge: Intel Corp. 460GX - 82466GX Wide and fast PCI
| >eXpander Bridge (WXB) (rev 07)
| > Subsystem: Intel Corp. 460GX - 82466GX Wide and fast PCI
| >eXpander Bridge (WXB)
| > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
| >ParErr+ Stepping- SERR+ FastB2B-
| > Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort+ >SERR- <PERR-
| > Latency: 32, cache line size 10
| > Capabilities: [90] Power Management version 2
| > Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
| >PME(D0-,D1-,D2-,D3hot-,D3cold-)
| > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
| >
| >15:14.0 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:14.1 Host bridge: Intel Corp. 460GX - 82466GX Wide and fast PCI
| >eXpander Bridge (WXB) (rev 07)
| > Subsystem: Intel Corp. 460GX - 82466GX Wide and fast PCI
| >eXpander Bridge (WXB)
| > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
| >ParErr+ Stepping- SERR+ FastB2B-
| > Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Latency: 32, cache line size 10
| > Capabilities: [90] Power Management version 2
| > Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
| >PME(D0-,D1-,D2-,D3hot-,D3cold-)
| > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
| >
| >15:15.0 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:15.1 Host bridge: Intel Corp. 460GX - 82466GX Wide and fast PCI
| >eXpander Bridge (WXB) (rev 07)
| > Subsystem: Intel Corp. 460GX - 82466GX Wide and fast PCI
| >eXpander Bridge (WXB)
| > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
| >ParErr+ Stepping- SERR+ FastB2B-
| > Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Latency: 32, cache line size 10
| > Capabilities: [90] Power Management version 2
| > Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
| >PME(D0-,D1-,D2-,D3hot-,D3cold-)
| > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
| >
| >15:16.0 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:16.1 Host bridge: Intel Corp. 460GX - 82466GX Wide and fast PCI
| >eXpander Bridge (WXB) (rev 07)
| > Subsystem: Intel Corp. 460GX - 82466GX Wide and fast PCI
| >eXpander Bridge (WXB)
| > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
| >ParErr+ Stepping- SERR+ FastB2B-
| > Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Latency: 32, cache line size 10
| > Capabilities: [90] Power Management version 2
| > Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
| >PME(D0-,D1-,D2-,D3hot-,D3cold-)
| > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
| >
| >15:17.0 Host bridge: Intel Corp. 460GX - 84460GX System Address
| >Controller (SAC) (rev 03)
| > Subsystem: Intel Corp. 460GX - 84460GX System Address Controller
| >(SAC)
| > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
| >ParErr- Stepping- SERR- FastB2B-
| > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| >
| >15:17.1 Host bridge: Intel Corp. 460GX - 82466GX Wide and fast PCI
| >eXpander Bridge (WXB) (rev 07)
| > Subsystem: Intel Corp. 460GX - 82466GX Wide and fast PCI
| >eXpander Bridge (WXB)
| > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
| >ParErr+ Stepping- SERR+ FastB2B-
| > Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
| ><TAbort- <MAbort- >SERR- <PERR-
| > Latency: 32, cache line size 10
| > Capabilities: [90] Power Management version 2
| > Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
| >PME(D0-,D1-,D2-,D3hot-,D3cold-)
| > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
| >-
| >To unsubscribe from this list: send the line "unsubscribe
| >linux-ia64" in
| >the body of a message to majordomo@vger.kernel.org
| >More majordomo info at http://vger.kernel.org/majordomo-info.html
| >
| -
| To unsubscribe from this list: send the line "unsubscribe linux-ia64" in
| the body of a message to majordomo@vger.kernel.org
| More majordomo info at http://vger.kernel.org/majordomo-info.html
--
~Randy
next prev parent reply other threads:[~2004-05-25 15:02 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-05-13 8:04 IA64 test report:USB mouse donesn't work : 2.4.26 /Lion 2004-5-12: 9/10 pass Wang, Zhenyu Z
2004-05-25 12:07 ` Yu, Luming
2004-05-25 15:02 ` Randy.Dunlap [this message]
2004-05-25 15:25 ` Yu, Luming
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20040525080209.4ef5271a.rddunlap@osdl.org \
--to=rddunlap@osdl.org \
--cc=linux-ia64@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox