From: Jonathan Cameron <jic23@kernel.org>
To: Philipp Jungkamp <p.jungkamp@gmx.net>
Cc: Jiri Kosina <jikos@kernel.org>,
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>,
linux-iio@vger.kernel.org
Subject: Re: [PATCH v4 4/4] IIO: hid-sensor-prox: Use generic usage
Date: Sat, 26 Nov 2022 19:04:29 +0000 [thread overview]
Message-ID: <20221126190429.1ca14050@jic23-huawei> (raw)
In-Reply-To: <20221124233841.3103-5-p.jungkamp@gmx.net>
On Fri, 25 Nov 2022 00:38:41 +0100
Philipp Jungkamp <p.jungkamp@gmx.net> wrote:
> Use a generic 'hsdev->usage' instead of the HID_USAGE_SENSOR_PROX to
> allow this driver to drive the Lenvo custom proximity sensor, which is
> registered under a 'custom' usage and not HID_USAGE_SENSOR_PROX.
>
> Add the Lenovo Intelligent Sensing Solution (LISS) human presence sensor
> to the platform device ids.
>
> Signed-off-by: Philipp Jungkamp <p.jungkamp@gmx.net>
I gave a tag for this - if you deliberately didn't add it, I'd expect to see
a reason why.
Ah well, here it is again.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
> ---
>
> v2:
> - Remove some unnecessary newlines in function calls.
>
> v3:
> - No change.
>
> v4:
> - Clean up switch statement.
>
> drivers/iio/light/hid-sensor-prox.c | 37 ++++++++++++++++++-----------
> 1 file changed, 23 insertions(+), 14 deletions(-)
>
> diff --git a/drivers/iio/light/hid-sensor-prox.c b/drivers/iio/light/hid-sensor-prox.c
> index f10fa2abfe72..a47591e1bad9 100644
> --- a/drivers/iio/light/hid-sensor-prox.c
> +++ b/drivers/iio/light/hid-sensor-prox.c
> @@ -61,6 +61,7 @@ static int prox_read_raw(struct iio_dev *indio_dev,
> long mask)
> {
> struct prox_state *prox_state = iio_priv(indio_dev);
> + struct hid_sensor_hub_device *hsdev;
> int report_id = -1;
> u32 address;
> int ret_type;
> @@ -75,6 +76,7 @@ static int prox_read_raw(struct iio_dev *indio_dev,
> report_id = prox_state->prox_attr.report_id;
> min = prox_state->prox_attr.logical_minimum;
> address = HID_USAGE_SENSOR_HUMAN_PRESENCE;
> + hsdev = prox_state->common_attributes.hsdev;
> break;
> default:
> report_id = -1;
> @@ -84,11 +86,8 @@ static int prox_read_raw(struct iio_dev *indio_dev,
> hid_sensor_power_state(&prox_state->common_attributes,
> true);
> *val = sensor_hub_input_attr_get_raw_value(
> - prox_state->common_attributes.hsdev,
> - HID_USAGE_SENSOR_PROX, address,
> - report_id,
> - SENSOR_HUB_SYNC,
> - min < 0);
> + hsdev, hsdev->usage, address, report_id,
> + SENSOR_HUB_SYNC, min < 0);
> hid_sensor_power_state(&prox_state->common_attributes,
> false);
> } else {
> @@ -191,10 +190,16 @@ static int prox_capture_sample(struct hid_sensor_hub_device *hsdev,
>
> switch (usage_id) {
> case HID_USAGE_SENSOR_HUMAN_PRESENCE:
> - prox_state->human_presence = *(u32 *)raw_data;
> - ret = 0;
> - break;
> - default:
> + switch (raw_len) {
> + case 1:
> + prox_state->human_presence = *(u8 *)raw_data;
> + return 0;
> + case 4:
> + prox_state->human_presence = *(u32 *)raw_data;
> + return 0;
> + default:
> + break;
> + }
> break;
> }
>
> @@ -244,7 +249,7 @@ static int hid_prox_probe(struct platform_device *pdev)
> prox_state->common_attributes.hsdev = hsdev;
> prox_state->common_attributes.pdev = pdev;
>
> - ret = hid_sensor_parse_common_attributes(hsdev, HID_USAGE_SENSOR_PROX,
> + ret = hid_sensor_parse_common_attributes(hsdev, hsdev->usage,
> &prox_state->common_attributes,
> prox_sensitivity_addresses,
> ARRAY_SIZE(prox_sensitivity_addresses));
> @@ -262,7 +267,7 @@ static int hid_prox_probe(struct platform_device *pdev)
>
> ret = prox_parse_report(pdev, hsdev,
> (struct iio_chan_spec *)indio_dev->channels,
> - HID_USAGE_SENSOR_PROX, prox_state);
> + hsdev->usage, prox_state);
> if (ret) {
> dev_err(&pdev->dev, "failed to setup attributes\n");
> return ret;
> @@ -291,8 +296,8 @@ static int hid_prox_probe(struct platform_device *pdev)
> prox_state->callbacks.send_event = prox_proc_event;
> prox_state->callbacks.capture_sample = prox_capture_sample;
> prox_state->callbacks.pdev = pdev;
> - ret = sensor_hub_register_callback(hsdev, HID_USAGE_SENSOR_PROX,
> - &prox_state->callbacks);
> + ret = sensor_hub_register_callback(hsdev, hsdev->usage,
> + &prox_state->callbacks);
> if (ret < 0) {
> dev_err(&pdev->dev, "callback reg failed\n");
> goto error_iio_unreg;
> @@ -314,7 +319,7 @@ static int hid_prox_remove(struct platform_device *pdev)
> struct iio_dev *indio_dev = platform_get_drvdata(pdev);
> struct prox_state *prox_state = iio_priv(indio_dev);
>
> - sensor_hub_remove_callback(hsdev, HID_USAGE_SENSOR_PROX);
> + sensor_hub_remove_callback(hsdev, hsdev->usage);
> iio_device_unregister(indio_dev);
> hid_sensor_remove_trigger(indio_dev, &prox_state->common_attributes);
>
> @@ -326,6 +331,10 @@ static const struct platform_device_id hid_prox_ids[] = {
> /* Format: HID-SENSOR-usage_id_in_hex_lowercase */
> .name = "HID-SENSOR-200011",
> },
> + {
> + /* Format: HID-SENSOR-tag-usage_id_in_hex_lowercase */
> + .name = "HID-SENSOR-LISS-0226",
> + },
> { /* sentinel */ }
> };
> MODULE_DEVICE_TABLE(platform, hid_prox_ids);
> --
> 2.38.1
>
next prev parent reply other threads:[~2022-11-26 18:51 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-11-24 23:38 [PATCH v4 0/4] IIO: More HID custom sensors Philipp Jungkamp
2022-11-24 23:38 ` [PATCH v4 1/4] HID: hid-sensor-custom: Allow more custom iio sensors Philipp Jungkamp
2022-11-26 19:11 ` Jonathan Cameron
2022-11-24 23:38 ` [PATCH v4 2/4] HID: hid-sensor-custom: Add LISS custom sensors Philipp Jungkamp
2022-11-26 19:11 ` Jonathan Cameron
2022-11-24 23:38 ` [PATCH v4 3/4] IIO: hid-sensor-als: Use generic usage Philipp Jungkamp
2022-11-26 19:05 ` Jonathan Cameron
2022-11-24 23:38 ` [PATCH v4 4/4] IIO: hid-sensor-prox: " Philipp Jungkamp
2022-11-26 19:04 ` Jonathan Cameron [this message]
2022-11-27 17:33 ` [PATCH v4 0/4] IIO: More HID custom sensors srinivas pandruvada
2022-12-13 22:51 ` Philipp Jungkamp
2022-12-14 9:27 ` Jonathan Cameron
2022-12-14 17:20 ` Jiri Kosina
2022-12-15 16:21 ` Jonathan Cameron
2022-12-20 14:26 ` Jiri Kosina
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20221126190429.1ca14050@jic23-huawei \
--to=jic23@kernel.org \
--cc=jikos@kernel.org \
--cc=linux-iio@vger.kernel.org \
--cc=p.jungkamp@gmx.net \
--cc=srinivas.pandruvada@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox