* [PATCHv3 2/4] Input: edt_ft5x06: use devm_* functions where appropriate
2014-01-17 12:28 Input: edt-ft5x06: Add DT support Lothar Waßmann
2014-01-17 12:28 ` [PATCHv3 1/4] DT: Add vendor prefix for Emerging Display Technologies Lothar Waßmann
@ 2014-01-17 12:28 ` Lothar Waßmann
2014-01-17 12:28 ` [PATCHv3 3/4] Input: edt-ft5x06: Add DT support Lothar Waßmann
2014-01-17 12:28 ` [PATCHv3 4/4] Input: edt-ft5x06 adjust reset delays according to datasheet Lothar Waßmann
3 siblings, 0 replies; 7+ messages in thread
From: Lothar Waßmann @ 2014-01-17 12:28 UTC (permalink / raw)
To: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Rob Landley, Dmitry Torokhov, Thierry Reding, Grant Likely,
Jonathan Cameron, Shawn Guo, Silvio F, Guennadi Liakhovetski,
Jingoo Han, Fugang Duan, Sachin Kamat, devicetree, linux-doc,
linux-kernel, linux-input
Cc: Lothar Waßmann
Simplify the error path and remove() function by using devm_*
functions for requesting gpios and irq and allocating memory.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
---
drivers/input/touchscreen/edt-ft5x06.c | 66 +++++++++++---------------------
1 files changed, 23 insertions(+), 43 deletions(-)
diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
index af0d68b..583c053 100644
--- a/drivers/input/touchscreen/edt-ft5x06.c
+++ b/drivers/input/touchscreen/edt-ft5x06.c
@@ -366,7 +366,9 @@ static int edt_ft5x06_factory_mode(struct edt_ft5x06_ts_data *tsdata)
if (!tsdata->raw_buffer) {
tsdata->raw_bufsize = tsdata->num_x * tsdata->num_y *
sizeof(u16);
- tsdata->raw_buffer = kzalloc(tsdata->raw_bufsize, GFP_KERNEL);
+ tsdata->raw_buffer = devm_kzalloc(&client->dev,
+ tsdata->raw_bufsize,
+ GFP_KERNEL);
if (!tsdata->raw_buffer) {
error = -ENOMEM;
goto err_out;
@@ -623,8 +625,9 @@ static int edt_ft5x06_ts_reset(struct i2c_client *client,
if (gpio_is_valid(reset_pin)) {
/* this pulls reset down, enabling the low active reset */
- error = gpio_request_one(reset_pin, GPIOF_OUT_INIT_LOW,
- "edt-ft5x06 reset");
+ error = devm_gpio_request_one(&client->dev, reset_pin,
+ GPIOF_OUT_INIT_LOW,
+ "edt-ft5x06 reset");
if (error) {
dev_err(&client->dev,
"Failed to request GPIO %d as reset pin, error %d\n",
@@ -723,7 +726,7 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
return error;
if (gpio_is_valid(pdata->irq_pin)) {
- error = gpio_request_one(pdata->irq_pin,
+ error = devm_gpio_request_one(&client->dev, pdata->irq_pin,
GPIOF_IN, "edt-ft5x06 irq");
if (error) {
dev_err(&client->dev,
@@ -733,12 +736,11 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
}
}
- tsdata = kzalloc(sizeof(*tsdata), GFP_KERNEL);
- input = input_allocate_device();
+ tsdata = devm_kzalloc(&client->dev, sizeof(*tsdata), GFP_KERNEL);
+ input = devm_input_allocate_device(&client->dev);
if (!tsdata || !input) {
- dev_err(&client->dev, "failed to allocate driver data.\n");
- error = -ENOMEM;
- goto err_free_mem;
+ dev_err(&client->dev, "failed to allocate input device.\n");
+ return -ENOMEM;
}
mutex_init(&tsdata->mutex);
@@ -749,7 +751,7 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
error = edt_ft5x06_ts_identify(client, tsdata->name, fw_version);
if (error) {
dev_err(&client->dev, "touchscreen probe failed\n");
- goto err_free_mem;
+ return error;
}
edt_ft5x06_ts_get_defaults(tsdata, pdata);
@@ -776,27 +778,30 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
error = input_mt_init_slots(input, MAX_SUPPORT_POINTS, 0);
if (error) {
dev_err(&client->dev, "Unable to init MT slots.\n");
- goto err_free_mem;
+ return error;
}
input_set_drvdata(input, tsdata);
i2c_set_clientdata(client, tsdata);
- error = request_threaded_irq(client->irq, NULL, edt_ft5x06_ts_isr,
- IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
- client->name, tsdata);
+ error = devm_request_threaded_irq(&client->dev, client->irq, NULL,
+ edt_ft5x06_ts_isr,
+ IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+ client->name, tsdata);
if (error) {
dev_err(&client->dev, "Unable to request touchscreen IRQ.\n");
- goto err_free_mem;
+ return error;
}
error = sysfs_create_group(&client->dev.kobj, &edt_ft5x06_attr_group);
if (error)
- goto err_free_irq;
+ return error;
error = input_register_device(input);
- if (error)
- goto err_remove_attrs;
+ if (error) {
+ sysfs_remove_group(&client->dev.kobj, &edt_ft5x06_attr_group);
+ return error;
+ }
edt_ft5x06_ts_prepare_debugfs(tsdata, dev_driver_string(&client->dev));
device_init_wakeup(&client->dev, 1);
@@ -806,40 +811,15 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
pdata->irq_pin, pdata->reset_pin);
return 0;
-
-err_remove_attrs:
- sysfs_remove_group(&client->dev.kobj, &edt_ft5x06_attr_group);
-err_free_irq:
- free_irq(client->irq, tsdata);
-err_free_mem:
- input_free_device(input);
- kfree(tsdata);
-
- if (gpio_is_valid(pdata->irq_pin))
- gpio_free(pdata->irq_pin);
-
- return error;
}
static int edt_ft5x06_ts_remove(struct i2c_client *client)
{
- const struct edt_ft5x06_platform_data *pdata =
- dev_get_platdata(&client->dev);
struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
edt_ft5x06_ts_teardown_debugfs(tsdata);
sysfs_remove_group(&client->dev.kobj, &edt_ft5x06_attr_group);
- free_irq(client->irq, tsdata);
- input_unregister_device(tsdata->input);
-
- if (gpio_is_valid(pdata->irq_pin))
- gpio_free(pdata->irq_pin);
- if (gpio_is_valid(pdata->reset_pin))
- gpio_free(pdata->reset_pin);
-
- kfree(tsdata);
-
return 0;
}
--
1.7.2.5
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCHv3 3/4] Input: edt-ft5x06: Add DT support
2014-01-17 12:28 Input: edt-ft5x06: Add DT support Lothar Waßmann
2014-01-17 12:28 ` [PATCHv3 1/4] DT: Add vendor prefix for Emerging Display Technologies Lothar Waßmann
2014-01-17 12:28 ` [PATCHv3 2/4] Input: edt_ft5x06: use devm_* functions where appropriate Lothar Waßmann
@ 2014-01-17 12:28 ` Lothar Waßmann
2014-01-17 12:28 ` [PATCHv3 4/4] Input: edt-ft5x06 adjust reset delays according to datasheet Lothar Waßmann
3 siblings, 0 replies; 7+ messages in thread
From: Lothar Waßmann @ 2014-01-17 12:28 UTC (permalink / raw)
To: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Rob Landley, Dmitry Torokhov, Thierry Reding, Grant Likely,
Jonathan Cameron, Shawn Guo, Silvio F, Guennadi Liakhovetski,
Jingoo Han, Fugang Duan, Sachin Kamat, devicetree, linux-doc,
linux-kernel, linux-input
Cc: Lothar Waßmann
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
---
.../bindings/input/touchscreen/edt-ft5x06.txt | 29 +++++
drivers/input/touchscreen/edt-ft5x06.c | 121 +++++++++++++++++---
2 files changed, 132 insertions(+), 18 deletions(-)
create mode 100644 Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
new file mode 100644
index 0000000..826b564
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
@@ -0,0 +1,29 @@
+* EDT FT5x06 Multiple Touch Controller
+
+Required properties:
+- compatible: must be "edt,ft5x06"
+- reg: i2c slave address
+- interrupt-parent: the phandle for the interrupt controller
+- interrupts: touch controller interrupt
+
+Optional properties:
+- reset-gpios: the gpio pin to be used for resetting the controller
+- wake-gpios: the gpio pin to be used for waking up the controller
+
+ The following properties provide default values for the
+ corresponding parameters (see Documentation/input/edt-ft5x06.txt)
+- edt,threshold: allows setting the "click"-threshold in the range from 20 to 80.
+- edt,gain: sensitivity (0..31) (lower value -> higher sensitivity)
+- edt,offset: edge compensation (0..31)
+- edt,report-rate: report rate (3..14) events per 100ms
+
+Example:
+
+ edt_ft5x06@38 {
+ compatible = "edt,ft5x06";
+ reg = <0x38>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <5 0>;
+ reset-gpios = <&gpio2 6 1>;
+ wake-gpios = <&gpio4 9 0>;
+ };
diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
index 583c053..ec6b3e5 100644
--- a/drivers/input/touchscreen/edt-ft5x06.c
+++ b/drivers/input/touchscreen/edt-ft5x06.c
@@ -33,6 +33,7 @@
#include <linux/debugfs.h>
#include <linux/slab.h>
#include <linux/gpio.h>
+#include <linux/of_gpio.h>
#include <linux/input/mt.h>
#include <linux/input/edt-ft5x06.h>
@@ -65,6 +66,10 @@ struct edt_ft5x06_ts_data {
u16 num_x;
u16 num_y;
+ int reset_pin;
+ int irq_pin;
+ int wake_pin;
+
#if defined(CONFIG_DEBUG_FS)
struct dentry *debug_dir;
u8 *raw_buffer;
@@ -481,7 +486,7 @@ static int edt_ft5x06_debugfs_mode_set(void *data, u64 mode)
if (mode != tsdata->factory_mode) {
retval = mode ? edt_ft5x06_factory_mode(tsdata) :
- edt_ft5x06_work_mode(tsdata);
+ edt_ft5x06_work_mode(tsdata);
}
mutex_unlock(&tsdata->mutex);
@@ -619,24 +624,37 @@ edt_ft5x06_ts_teardown_debugfs(struct edt_ft5x06_ts_data *tsdata)
static int edt_ft5x06_ts_reset(struct i2c_client *client,
- int reset_pin)
+ struct edt_ft5x06_ts_data *tsdata)
{
int error;
- if (gpio_is_valid(reset_pin)) {
+ if (gpio_is_valid(tsdata->wake_pin)) {
+ error = devm_gpio_request_one(&client->dev, tsdata->wake_pin,
+ GPIOF_OUT_INIT_LOW, "edt-ft5x06 wake");
+ if (error) {
+ dev_err(&client->dev,
+ "Failed to request GPIO %d as wake pin, error %d\n",
+ tsdata->wake_pin, error);
+ return error;
+ }
+
+ mdelay(5);
+ gpio_set_value(tsdata->wake_pin, 1);
+ }
+ if (gpio_is_valid(tsdata->reset_pin)) {
/* this pulls reset down, enabling the low active reset */
- error = devm_gpio_request_one(&client->dev, reset_pin,
+ error = devm_gpio_request_one(&client->dev, tsdata->reset_pin,
GPIOF_OUT_INIT_LOW,
"edt-ft5x06 reset");
if (error) {
dev_err(&client->dev,
"Failed to request GPIO %d as reset pin, error %d\n",
- reset_pin, error);
+ tsdata->reset_pin, error);
return error;
}
mdelay(50);
- gpio_set_value(reset_pin, 1);
+ gpio_set_value(tsdata->reset_pin, 1);
mdelay(100);
}
@@ -677,6 +695,29 @@ static int edt_ft5x06_ts_identify(struct i2c_client *client,
pdata->name <= edt_ft5x06_attr_##name.limit_high) \
edt_ft5x06_register_write(tsdata, reg, pdata->name)
+#define EDT_GET_PROP(name, var, reg) { \
+ u32 val; \
+ if (of_property_read_u32(np, name, &val) == 0) { \
+ if (val >= edt_ft5x06_attr_##var.limit_low && \
+ val <= edt_ft5x06_attr_##var.limit_high) \
+ edt_ft5x06_register_write(tsdata, reg, val); \
+ else \
+ pr_err("edt_ft5x06: property %s (%u) is out of range: %u..%u", \
+ name, val, edt_ft5x06_attr_##var.limit_low, \
+ edt_ft5x06_attr_##var.limit_high); \
+ } \
+}
+
+static void edt_ft5x06_ts_get_dt_defaults(struct device_node *np,
+ struct edt_ft5x06_ts_data *tsdata)
+{
+ /* pick up defaults from the DT data */
+ EDT_GET_PROP("edt,threshold", threshold, WORK_REGISTER_THRESHOLD);
+ EDT_GET_PROP("edt,gain", gain, WORK_REGISTER_GAIN);
+ EDT_GET_PROP("edt,offset", offset, WORK_REGISTER_OFFSET);
+ EDT_GET_PROP("edt,report-rate", report_rate, WORK_REGISTER_REPORT_RATE);
+}
+
static void
edt_ft5x06_ts_get_defaults(struct edt_ft5x06_ts_data *tsdata,
const struct edt_ft5x06_platform_data *pdata)
@@ -704,6 +745,33 @@ edt_ft5x06_ts_get_parameters(struct edt_ft5x06_ts_data *tsdata)
tsdata->num_y = edt_ft5x06_register_read(tsdata, WORK_REGISTER_NUM_Y);
}
+#ifdef CONFIG_OF
+static int edt_ft5x06_i2c_ts_probe_dt(struct device *dev,
+ struct edt_ft5x06_ts_data *tsdata)
+{
+ struct device_node *np = dev->of_node;
+
+ if (!np)
+ return -ENODEV;
+
+ /*
+ * irq_pin is not needed for DT setup.
+ * irq is associated via 'interrupts' property in DT
+ */
+ tsdata->irq_pin = -EINVAL;
+ tsdata->reset_pin = of_get_named_gpio(np, "reset-gpios", 0);
+ tsdata->wake_pin = of_get_named_gpio(np, "wake-gpios", 0);
+
+ return 0;
+}
+#else
+static inline int edt_ft5x06_i2c_ts_probe_dt(struct device *dev,
+ struct edt_ft5x06_i2c_ts_data *tsdata)
+{
+ return -ENODEV;
+}
+#endif
+
static int edt_ft5x06_ts_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
@@ -716,29 +784,42 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
dev_dbg(&client->dev, "probing for EDT FT5x06 I2C\n");
+ tsdata = devm_kzalloc(&client->dev, sizeof(*tsdata), GFP_KERNEL);
+ if (!tsdata) {
+ dev_err(&client->dev, "failed to allocate driver data.\n");
+ return -ENOMEM;
+ }
+
if (!pdata) {
- dev_err(&client->dev, "no platform data?\n");
- return -EINVAL;
+ error = edt_ft5x06_i2c_ts_probe_dt(&client->dev, tsdata);
+ if (error) {
+ dev_err(&client->dev,
+ "DT probe failed and no platform data present\n");
+ return error;
+ }
+ } else {
+ tsdata->reset_pin = pdata->reset_pin;
+ tsdata->irq_pin = pdata->irq_pin;
+ tsdata->wake_pin = -EINVAL;
}
- error = edt_ft5x06_ts_reset(client, pdata->reset_pin);
+ error = edt_ft5x06_ts_reset(client, tsdata);
if (error)
return error;
- if (gpio_is_valid(pdata->irq_pin)) {
- error = devm_gpio_request_one(&client->dev, pdata->irq_pin,
- GPIOF_IN, "edt-ft5x06 irq");
+ if (gpio_is_valid(tsdata->irq_pin)) {
+ error = devm_gpio_request_one(&client->dev, tsdata->irq_pin,
+ GPIOF_IN, "edt-ft5x06 irq");
if (error) {
dev_err(&client->dev,
"Failed to request GPIO %d, error %d\n",
- pdata->irq_pin, error);
+ tsdata->irq_pin, error);
return error;
}
}
- tsdata = devm_kzalloc(&client->dev, sizeof(*tsdata), GFP_KERNEL);
input = devm_input_allocate_device(&client->dev);
- if (!tsdata || !input) {
+ if (!input) {
dev_err(&client->dev, "failed to allocate input device.\n");
return -ENOMEM;
}
@@ -754,7 +835,11 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
return error;
}
- edt_ft5x06_ts_get_defaults(tsdata, pdata);
+ if (!pdata)
+ edt_ft5x06_ts_get_dt_defaults(client->dev.of_node, tsdata);
+ else
+ edt_ft5x06_ts_get_defaults(tsdata, pdata);
+
edt_ft5x06_ts_get_parameters(tsdata);
dev_dbg(&client->dev,
@@ -807,8 +892,8 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
device_init_wakeup(&client->dev, 1);
dev_dbg(&client->dev,
- "EDT FT5x06 initialized: IRQ pin %d, Reset pin %d.\n",
- pdata->irq_pin, pdata->reset_pin);
+ "EDT FT5x06 initialized: IRQ %d, WAKE pin %d, Reset pin %d.\n",
+ client->irq, tsdata->wake_pin, tsdata->reset_pin);
return 0;
}
--
1.7.2.5
^ permalink raw reply related [flat|nested] 7+ messages in thread